ION Director Manual
ION Director Manual
Instruction Manual
As of 2022-01-31
Instruction Manual ION Director®
Table of Contents
GET THE MOST OUT OF YOUR GHL PRODUCT .......................................................................................................................... 5
1 SAFETY INSTRUCTIONS....................................................................................................................................... 5
1.1 SAFETY OF CHILDREN AND VULNERABLE PERSONS ........................................................................................................ 6
1.2 INTENDED USE ...................................................................................................................................................... 6
2 GENERAL ............................................................................................................................................................ 8
2.1 ABOUT THIS MANUAL ............................................................................................................................................. 8
2.2 FEATURES............................................................................................................................................................. 8
2.3 SCOPE OF DELIVERY................................................................................................................................................ 8
3 CONNECTIONS OF THE ION DIRECTOR®.............................................................................................................. 9
3.1 GENERAL.............................................................................................................................................................. 9
3.2 CONNECTION OVERVIEW ....................................................................................................................................... 10
3.2.1 MUI Sensor Connection ............................................................................................................................. 10
3.2.2 PAB-Ports .................................................................................................................................................. 11
3.2.3 AUX Port .................................................................................................................................................... 11
3.2.4 Return Vent ............................................................................................................................................... 11
3.2.5 Power Supply............................................................................................................................................. 11
4 ACTIVATION ..................................................................................................................................................... 12
4.1 CONFIGURATION OPTIONS..................................................................................................................................... 12
4.1.1 Operation with GHL Doser 2.1 Stand Alone .............................................................................................. 13
4.1.2 Operation with ProfiLux Aquarium Controller and GHL Doser Maxi Stand Alone ..................................... 13
4.2 ESTABLISHING THE PAB CONNECTION ...................................................................................................................... 13
4.3 STATUS INDICATORS OF THE ION DIRECTOR® ............................................................................................................ 14
4.3.1 System-Status- LED on the housing cover ................................................................................................. 14
4.3.2 PAB Status LEDs on the Back Panel ........................................................................................................... 15
4.4 PLACING THE ION DIRECTOR® ............................................................................................................................... 15
4.5 HOW IT WORKS ................................................................................................................................................... 18
4.6 SELECTION AND ASSIGNMENT OF THE PUMPS ............................................................................................................ 19
4.7 ACTIVATION OF THE PUMPS ................................................................................................................................... 20
4.8 INSTALLING THE TUBES.......................................................................................................................................... 21
4.8.1 Installing the water filter .......................................................................................................................... 24
4.8.2 Installing the return tube .......................................................................................................................... 24
4.9 PREPARATION OF THE MUI SENSOR ........................................................................................................................ 24
4.10 INSTALLING THE MUI SENSOR ................................................................................................................................ 25
4.11 CONNECTING THE MULTI ION SENSOR ..................................................................................................................... 27
4.12 REMOVING THE MULTI ION SENSOR ........................................................................................................................ 27
5 CARRYING OUT THE MEASUREMENT ............................................................................................................... 29
5.1 ENTER SAMPLE TUBE VOLUME ................................................................................................................................ 29
5.2 PREPARE MEASUREMENT ....................................................................................................................................... 30
5.3 MANUAL MEASUREMENT ...................................................................................................................................... 31
5.4 DAILY AUTOMATED MEASUREMENT ......................................................................................................................... 32
5.5 ALARM .............................................................................................................................................................. 32
6 CONTROL ......................................................................................................................................................... 32
6.1 SIMPLE CONTROL: SWITCHING SOCKETS.................................................................................................................... 33
6.2 CONTROL VIA DOSING PUMPS ................................................................................................................................. 33
7 MEASUREMENT ACCURACY ............................................................................................................................. 33
EN 2022-01-31 2
Instruction Manual ION Director®
EN 2022-01-31 3
Instruction Manual ION Director®
Please note that the ION Director® does not have an internal controller and therefore requires
for operation a ProfiLux 3 Aquarium controller with latest firmware (6.44 or newer), a ProfiLux
4 (7.25 or newer), a GHL Doser 2 (2.1) Stand Alone or GHL Doser Maxi Stand Alone both with
firmware 1.37 or higher. GHL products and their firmware and software are subject to
continuous development, so please ensure that you always use the latest version.
For transporting liquids to the ION Director® a GHL Doser 2/2.1 (Stand Alone or Slave) with at
least 3 free pumps is required.
We are confident that our product will help make your hobby more efficient, safe, and
ultimately help you spend more time enjoying your aquarium.
EN 2022-01-31 4
Instruction Manual ION Director®
1 Safety Instructions
Please read these instructions carefully before operating the ION Director®.
GHL products are built with maximum security and safety in mind. However, product safety
for this device can only be guaranteed if you follow these guidelines.
Anyone who uses this device must become familiar with the following safety instructions and
the operation of the device.
Be sure to read also over the safety instructions provided by ProfiLux/Doser manual;
including the respective manuals of other equipment manufacturers.
TIP
General note, tip or advice.
WARNING
Important note for operation, to avoid damage to the equipment, and for
your safety.
EN 2022-01-31 5
Instruction Manual ION Director®
DANGER
Warning that non-compliance can result in injury or damage to the device.
WARNING
This equipment must not be used:
• By small children and vulnerable persons with limited physical,
sensory or mental capabilities.
• By people who are unfamiliar with the functions of this product.
The ION Director® may only be used to determine the respective ion concentrations of
aquarium water.
Make sure to place the device away from splashing water, moisture or other liquids.
WARNING
To ensure safe operation, the following guidelines must be followed.
Disregarding these safety guidelines, will result in voiding your warranty.
In which case, the manufacturer rejects any responsibility or liability for
damage!
WARNING
Moisture indicators are placed inside the unit and will change color when
exposed to excessive moisture.
Removing these indicators will void all warranty claims
EN 2022-01-31 6
Instruction Manual ION Director®
DANGER
Make sure that the power cord is plugged into a grounded outlet; otherwise
you could get an electric shock or cause a fire.
• Protect the power cable from damage (For example, twisting,
kinking, clamping). Please also pay attention to the joints and
connections to the device.
• Disconnect the power plug by pulling the plug, not the cable.
• Never attempt to disassemble, repair or alter the equipment by
yourself.
• Do not insert sharp objects into the electrical contacts and ports.
DANGER
• If the unit falls into the aquarium or has been exposed to moisture
or humidity, first turn off the power to the device via the fuse or
circuit breaker, then pull the power cord.
• Never touch the power plug with wet hands.
• If the device has become wet or dirty, thoroughly clean and dry it
with a dry cloth.
DANGER
• The device may not be operated if it has been damaged in any way
(e.g. damaged power cord or plug, liquids or objects have gotten
into the interior, device has been exposed to excessive moisture, the
normal operation is disturbed, or the device has been dropped.)
EN 2022-01-31 7
Instruction Manual ION Director®
DANGER
• Never leave your aquarium unsupervised for an extended amount
of time.
• The maximum amount of time without personal view depends on
how long your aquarium can survive without significant damage,
even when errors occur.
• Always remember that technology can fail and therefore
malfunctions can never be ruled out!
Power failures, incorrect settings, damage (For example, by water or
overvoltage) or simply an unexpected operating situation can lead to
fatal damage.
• The manufacturer declines any liability for (consequential) damage
or loss arising in connection with the use of the ION Director®, as far
as permitted by law
For your own safety, please look at the hazard prevention and safety instructions in the
chapters that follow.
2 General
2.1 About this Manual
These instructions apply to the operation of the ION Director®.
Settings are explained in this manual using the GHL Control Center PC software as an example.
Of course, all settings can just as well be made via the GHL Connect app, via the GHL cloud
service myGHL or via the web interface of the device, depending on personal preference.
2.2 Features
• 1 x Multi Ion Sensor (MUI-Sensor port), BNC-connector
• 2 x ProfiLux Aquatic Bus (PAB Western sockets)
• 1 x AUX port
• 5 x Tube connectors (Water sample, References A and B, Waste water, Vent connector)
• 1 x Power supply input (24 VDC)
EN 2022-01-31 8
Instruction Manual ION Director®
Please check to make sure all items are in perfect condition. In case of damage, immediately
contact the dealer from whom you purchased the ION Director®.
WARNING
A damaged ION Director® or components may not be put into operation
under any circumstances.
WARNING
• Connect only original accessories from GHL.
• Do not use force when plugging-in connectors. If a plug contact does
not fit check that you have chosen the correct socket and that the
orientation is correct.
DANGER
• Incorrect connection (For example inserting a USB connector into a
PAB connector) can lead to damaging the ION Director®.
• A repair caused by this, is not covered under warranty and will
therefore incur repair charges.
EN 2022-01-31 9
Instruction Manual ION Director®
DANGER
• The eight-pole Mini-DIN socket (MUI sensor input at IOND) as well as
the eight-pole Mini-DIN plug (at MUI sensor) can easily be damaged
permanently if not handled properly, e.g. when contacts are bent!
• Therefore, when plugging in the connector, make sure that the
polarity respectively the orientation is correct (arrow on connector
must be directed upwards)!
• The plug must be easy to insert, NEVER use force, insert with care!
• Mechanical damage to the plug and/or socket can lead to the
destruction of the ION Director®!
• A repair caused by this, is not covered under warranty and will
therefore incur repair charges.
EN 2022-01-31 10
Instruction Manual ION Director®
TIP
• The sensor is sensitive to interference due to the low signal level. To
obtain the best measurement results, it is therefore necessary to
ensure sufficient distance between the sensor and its cable and
sources of interference (e.g. ballasts, power lines, pumps,
entertainment electronics, etc.).
3.2.2 PAB-Ports
PAB devices are connected to the black RJ45 Western sockets. These are on the one hand the
control unit (ProfiLux 3/4/4e or GHL Doser Standalone), on the other hand possibly existing
further slave devices. Please also refer to the instructions in the operating manual of the
corresponding control unit.
To install, first connect each Y-ends of the splitter cable to the DC-connector of the ION
Director® (24 VDC, polarity: Inside +, outside -) and GHL Doser 2.1. Connect then the other end
of the splitter to the main power supply of the Doser.
Please note that the ION Director® and the GHL Doser are operated with 24 V, ProfiLux on the
other hand runs with 12 V. It is therefore not possible to tap the supply voltage for the ION
Director® from the ProfiLux.
Never connect 12 V consumers to 24 V power supplies (or vice versa), this will inevitably lead
to malfunction or destruction!
Use only the supplied original cables and power supplies for supplying power to the ION
Director® device.
EN 2022-01-31 11
Instruction Manual ION Director®
DANGER
• To establish the power supply, the supplied Power supply splitter-
cable may only be connected to the ION Director® and to the GHL
Doser 2.1 (24 V consumer) and its power supply unit.
• Under no circumstances connect 12 V consumers (e.g. ProfiLux) to 24
V power supply units (or vice versa), this will inevitably lead to
malfunction or destruction!
• A repair caused by this is not covered by warranty and is therefore
subject to a charge.
4 Activation
4.1 Configuration Options
DANGER
For conveying the liquids (sample water and referenced) to the ION
Director® only pumps of a GHL Doser 2/2.1 Slave or Stand Alone must be
used!
Never use other pumps for this purpose (also don’t use pumps of the GHL
Doser Maxi) – this may cause destruction of the ION Director®!
EN 2022-01-31 12
Instruction Manual ION Director®
To operate the device, an additional control unit (ProfiLux from model 3, GHL Doser Stand Alone
from model 2 or a GHL Maxi Doser Stand Alone) is required
4.1.2 Operation with ProfiLux Aquarium Controller and GHL Doser Maxi Stand
Alone
The ION Director® is connected to the ProfiLux 3/4 or a GHL Doser Maxi Stand Alone and a GHL
Doser 2 (2.1) Slave via the ProfiLux Aquatic Bus (PAB).
EN 2022-01-31 13
Instruction Manual ION Director®
PAB is an interference free CAN-Bus-System which allows for extremely secure data transfer
between all PAB devices such as for example ION Director® and GHL Doser 2.1. The range can
be up to 100 m (300 FT).
The required PAB cables are available in different lengths and are not included and must be
purchased. The IOND-Sets do include a PAB cable for connecting the IOND to the included
Doser.
TIP
• Be sure to obtain suitable PAB cables in the appropriate lengths to
meet your needs.
• PAB-cables are available online at GHL Store (EU) and GHL USA Shop
(US) in different lengths from 0.5 m up to 50 m.
To enable the operation of the ION Director®, the device needs to be assigned to the
respective controller. For thorough information on how to assign PAB devices please refer to
the corresponding Instruction manuals and our Knowledge Base on our website
www.aquariumcomputer.com.
The color and blink codes shown depend on the particular Firmware.
For the meaning of the blink codes, please refer to the Knowledge Base at our website
www.aquariumcomputer.com.
EN 2022-01-31 14
Instruction Manual ION Director®
Located on the back panel of the ION Director® are another two LEDs
that provide information about PAB connection status and PAB
communication status.
The upper yellow LED indicates proper communication within the PAB connection. The lower
green LED provides information about the status of the PAB communication.
Status Meaning
Make sure that the IOND cannot be affected by electromagnetic interference sources!
The ION Director® is a highly sensitive electronic measuring device. To accurately determine
ion concentration, it measures extremely low voltages with an accuracy of 10µV (that's a ten-
thousandth of a volt). Although the IOND electronics is designed to be as interference
EN 2022-01-31 15
Instruction Manual ION Director®
We therefore recommend placing the ION Director® as far as possible from potential sources
of interference. Sources of interference are:
In particular, third-party devices of non-optimal quality that do not comply with the permitted
maximum emission limits can cause problems. If you detect interference, you can take these
measures:
• Increase the distance to the interfering device (approx. 1 - 1.5m distance will usually be
sufficient).
• If this is not possible, shielding may help (simple shielding plate or aluminum foil) ...
• ... or the exchange of the strong disturbing device.
GHL products such as ProfiLux, Doser, Expansion-Box as well as cables connected to them
such as PAB cables and cables from the associated power supplies are not critical sources of
interference due to their high-quality design and they comply with all emission standards, the
ION Director® may be placed in their proximity. However, the power supplies belonging to
these GHL products should also be placed at a distance. This also applies to all other sensors
in general.
Use only the original supplied grounded power supplies for the operation of all GHL products.
These meet all requirements regarding electromagnetic interference and are grounded so
that external interference can be discharged against the ground potential of the wall outlet.
Vibrations can cause pressure changes in the measuring cell during the measurement, which
in turn can cause voltage fluctuations at the sensor in the µV range and thus lead to impaired
measurements. Vibrations are mainly generated by pumps. If vibrations or shocks during the
measurement cannot be ruled out at the installation location, the ION Director® must be
placed on a vibration-absorbing pad, e.g. on foam.
EN 2022-01-31 16
Instruction Manual ION Director®
The ION Director® as well as its accessories are destroyed by excess moisture or excess
humidity - Please observe the technical data and notes below!
Mains voltage operated devices and water can become a dangerous combination. Therefore,
it is essential to supply all mains voltage operated devices that are operated in or near the
aquarium with mains voltage via an GFCI breaker!
In order to avoid any danger, all mains-operated devices must be disconnected from the
mains; all plugs must be disconnected! When working in the aquarium, it can never be ruled
out that a heating element, a pump, or a luminaire is defective.
If the device is placed inside an aquarium cabinet, make sure that it is placed in an area free
from splashing water; moisture or liquids that can penetrate.
TIP
• Please ensure good access to the connections of the device
• Please consider the maximum cable lengths of the connected PAB
cables, sensors etc. when selecting the installation site
WARNING
• To ensure proper operation, the connection cables should never be
kinked, crimped, or positioned in an unsuitable way.
DANGER
• The ION Director® must be installed horizontally, with illuminated
GHL logo facing upwards.
• The maximum deviation from the horizontal must not exceed
+/- 3 °.
• Only when installed correctly an adequate measurement can be
carried out.
• The ION Director® may NEVER be used without a built-in MUI
sensor!
EN 2022-01-31 17
Instruction Manual ION Director®
The figure to the side shows a schematic representation of the operating principle.
The 3 tube inlets on the front of the ION Director® are connected to 3 dosing pumps of a
GHL Doser 2 (2.1). The precise dosing pumps handle the conveying of the liquids.
After starting the measuring process, first the sample tube is completely refilled, the water
previously present in the sample tube is returned to the aquarium (or the sump) through the
connection on the back (Vent). This ensures that a fresh sample is always used for the
measurement - and not older water that has been in the sample hose for a longer period of
time - and that the measurement result actually reflects the current situation in the tank; in
addition, no water is wasted during this flushing.
Afterwards, the sensor is calibrated and the measurement is carried out by slowly adding
reference liquids and the sample water.
EN 2022-01-31 18
Instruction Manual ION Director®
The sample water required for the measurement as well as the reference liquids are drained
off as wastewater (through wastewater outlet on the front of the device), this wastewater
must be collected in a separate container for later disposal.
WARNING
• ION Director® and GHL Doser (as well as ProfiLux if present) must be
positioned away and protected from splashing water and excess
humidity!
• Splashing water/saltwater and or condensing humidity (e.g.
occurring nearby the sump) will destroy the devices – this voids all
warranty claims!
• The waste water should generally be collected and disposed of.
However, it may be returned into the tank if the quantities of
reference liquids do not lead to significant or disturbing
changes of salinity or filling level.
• You may lead the return of the sample water back into the
tank.
EN 2022-01-31 19
Instruction Manual ION Director®
WARNING
When you changed settings for your device via the GCC, you must always
save them using the "Save changes" button.
For the measurement, three pumps of the GHL Doser 2.1 are required. As default, pumps 1-3
are preselected for the functions Water sample, Reference A and Reference B.
You can change that pump assignment. If you already have several Dosers in your system,
then take care when numbering the pumps that one number is not assigned more than once.
EN 2022-01-31 20
Instruction Manual ION Director®
DANGER
• Please carry out the calibration carefully.
• The pump calibration has a direct influence on the precision of the
measurement and control.
• The more precisely you perform the calibration, the more accurate
the ION measurement can be.
For safety reasons, ION measurements are only started if it is ensured that there is at least 30
ml of each Reference solution for the measurement in the respective dosing container.
Enter the container capacity. For the pumps that deliver the reference fluids (here 2 and 3),
the example shown here is 500 ml. You can also enter a minimum below which an alarm
should be triggered. The container is emptied by dosing, therefore choose Container is
emptied.
The Doser calculates the fill level indicator according to the specified capacity of 500 ml and
the filling level. If you choose a larger fluid container (for example, 1000 ml) at a later time,
then you need to save that again, so that this capacity change can be taken into account in the
level indicator.
To activate the level indicator, press the Refill container button and confirm with OK.
EN 2022-01-31 21
Instruction Manual ION Director®
Please note that depending on the chosen mounting method you need different tube lengths
between IOND and Doser. For orientation, you will find below a tabular overview of the
recommended tube lengths.
TIP
Make a note of the lengths of the 2 water sample tubes (here: sump/tank
to pump 1 and pump 1 to ION Director®) and add the two lengths. You will
need this total tube length later when determining the Sample tube volume.
In order to achieve maximum measuring accuracy, it is necessary to keep the tube to the
reference liquids as short as possible (in total max. 100 cm / 40”).
Insert the reference tubes through the pre-drilled screw caps provided and screw them onto
the reference liquid bottles. The tube ends should just touch the bottom of the bottles. These
screw caps must be used to prevent evaporation and excessive exchange with the ambient
air, otherwise the measurement results will be compromised.
The bottles with the reference liquids must be protected from strong light, otherwise the
chemical composition could change, which would affect the measurement accuracy. This
applies to both operation and storage.
Replace the reference liquids before they are too empty and air is drawn in. The level
indicators and the alarm functions of the corresponding pumps help you not to miss this
moment.
Make sure that bubbles cannot collect anywhere in the tube, for example because the tube
sags. The tube must therefore be routed steadily from the reference bottles to the
corresponding dosing pump.
EN 2022-01-31 22
Instruction Manual ION Director®
The sample tube must suck in clean water (i.e. after filtration) and must not suck in any air
and must safely be sufficiently deep below the water surface at all times. Even small bubbles
can lead to inaccurate measurement results or even premature sensor wear. The water
sample must therefore not be drawn in in areas with a strong flow, e.g. near pumps, returns,
skimmers. However, the water sample must also not be taken in "dead" corners where it may
not be possible to collect a representative sample. Lightly flowed areas without visible
turbulence and bubbles are ideal.
After connecting the tubes, the tubes of the pumps (here pumps 2 and 3), which feed the
reference liquids, must be primed. This can be done manually using the buttons on the GHL
Doser 2.1, via the app or via the GCC under Manual dosing. Pump until tubes are entirely
primed.
DANGER
• Only the enclosed Flex PVC tubes may be used, in other tubes too
large air bubbles can form.
• The sample tube must not suck in any air.
• Air bubbles in the measuring cell can lead to inaccurate
measurement results or even premature sensor wear.
• - Premature sensor wear due to the above-mentioned air in the
measuring cell is not covered by the manufacturer's warranty.
• Before activation, the connected reference tubes must be
completely primed.
• Carefully perform the priming, otherwise accurate measurement
results cannot be achieved.
• Guide the reference tubes in a way that no air bubbles can form
during operation.
EN 2022-01-31 23
Instruction Manual ION Director®
• The priming of the internal tubes will be done later (see 5 Carrying
out the Measurement).
Place the sensor in a suitable container and slowly fill it with tap water or deionized water (no
salty water!) until the front sensor slot is completely submerged (marked below as Min), do
not fill much more water than necessary for this (marked below as Max).
Allow the sensor to soak for at least 30 Minutes before proceeding to the next step.
EN 2022-01-31 24
Instruction Manual ION Director®
EN 2022-01-31 25
Instruction Manual ION Director®
Note the guide grooves on the right and left of the sensor shaft, which ensure precise
positioning.
Only if these
are met correctly the sensor can be pushed to the stop and thus sufficiently deep into the
measuring cell. Be careful and do not use force.
Max. 22mm!
Tighten the nut around the sensor as tight as possible to prevent water from escaping
and air from entering the measuring cell, use a suitable tool for this (e.g. a 24 mm
wrench).
TIP
To keep the rubber seal in the screw connection flexible and watertight, we
recommend rubbing the inside of the seal thinly with Vaseline before
installing the sensor, e.g. using a Q-tip. Do NOT remove the seal and do
EN 2022-01-31 26
Instruction Manual ION Director®
NOT loosen the nut completely. Vaseline must not touch active sensor
surfaces within the front slot.
DANGER
• Incorrect installation of the MUI sensor can destroy the ION
Director®, the sensor and surrounding items!
• The ION Director® must NEVER be used without the installed MUI
sensor!
• A defect caused by this - e.g. due to water leakage at the sensor - is
not covered by warranty, repair or replacement is therefore subject
to a charge
DANGER
• Sensor plugs (as well as all plugs) must not be moist when
connecting to the socket.
• The eight-pole Mini-DIN socket (MUI sensor input at IOND) as well
as the eight-pole Mini-DIN plug (at MUI sensor) can easily be
damaged irreparably if not handled properly, e.g. by bending
contacts!
• Therefore, when plugging in the connector, make sure that the
polarity is correct (arrow on connector must point upwards)!
• The plug must be easy to insert, NEVER use force, insert with care!
• Mechanical damage to the plug and/or socket can lead to the
destruction of the ION Director®!
• A repair caused by this is not covered by warranty and is therefore
subject to a repair charge.
The IOND has the function Empty measuring cell completely for this purpose. Execute this
function and follow the instructions (removing the tubes), then the sensor can be removed.
EN 2022-01-31 27
Instruction Manual ION Director®
If you want to store the sensor for later use, the remaining salt water from the active sensor
tip (the front, slotted area) must first be rinsed off with tap water or deionized water. This will
prevent salt crusts from forming and damaging the sensor during storage. The active sensor
tip should be kept dry during storage.
Please note that each wet-dry cycle will age the sensor faster, the sensor performance will
degrade and the ideal lifetime may no longer be reached. Therefore, remove and store the
sensor only in special cases.
When using a previously stored sensor again, prepare the sensor again as described in 4.9
Preparation of the MUI Sensor.
Place a cloth under the sensor and the screw connection to catch any residual liquid. You can
then loosen the nut (do not unscrew it completely) and remove the sensor.
DANGER
• The sensor must not be removed until the measuring cell has been
emptied!
• If the sensor has been removed without emptying the measuring
cell, the liquid in the measuring cell will leak out and may damage
the IOND and any equipment underneath!
• A repair caused by this is not covered by warranty and is therefore
subject to a repair charge.
EN 2022-01-31 28
Instruction Manual ION Director®
Carry out manual and automatic measurements only when the MUI sensor is installed
and the screw connection is screwed tight and watertight.
HINT
The measurement is only started if at least 30 ml of each reference liquid
is present!
Therefore, the ION Director® requires the exact Sample tube volume. When calculating the
volume, you are supported by a built-in tool. Just click on the calculator next to the input field
for the Sample tube volume. Enter the total tube length (including the sample tube between
the ION Director® and the dosing pump and including the tube length of the dosing pump
which is 12 cm / 4.2”) that you have connected and confirm with OK.
HINT
The inline filter volume must be added. The GHL inline filter has a volume
of 7 ml.
Example: The tube had a volume of 10 ml - then a sample tube volume of
17 ml has to be entered.
EN 2022-01-31 29
Instruction Manual ION Director®
After this step you have to wait at least 12 hours for the FIRST measurement; the sensor
needs this time for stabilization to be able to deliver precise results. After that, measurements
can be performed at any time.
EN 2022-01-31 30
Instruction Manual ION Director®
WARNING
The FIRST measurement can only be performed after at least 12 hours
after preparation of the measuring cell!
DANGER
• The sample water tube must always take water from an area
free of sediment, dirt and air bubbles! Dirt and/or sediment
will damage BOTH the dosing pumps and the IOND! In these
cases, the IOND will no longer provide a correct measurement. The
water sample tube must be positioned carefully so that only clean
water is pumped into the IOND.
• A filter must be installed before the water sample pump!
• Damages, caused by dirty sample water, are not covered by
warranty.
• It must always be ensured that there are no air bubbles in the
sample tubes, as these falsify the measurement result.
• Make sure that the tubes cannot draw air during operation.
• If you detect air in the hoses, prime them and then perform 5.2
Prepare measurement again.
EN 2022-01-31 31
Instruction Manual ION Director®
Measurements/day
As often (1 to 24) is measured daily at equal intervals
EXAMPLE
➢ You want to measure twice a day at 07:00 and 19:00.
1. Set for Measurements per day = 2
2. For Always measure at this time, set 07:00 (the second time is
automatically: 07:00 + 24h / 2 = 19:00)
NOTE
• In most cases, it will not be necessary to measure more than once
or twice a day. If the dosing pumps regulating the parameters are
used correctly and the control procedure explained below is
followed, sufficiently stable parameters can be reached.
• The more often you measure, the more reference fluids will be
consumed.
5.5 Alarm
The ION Director® can monitor the measured parameters and, if necessary, display alarms. To
do this, activate the alarm monitoring and specify the Lower and the Upper limit for the
permissible values. If measured values are outside these thresholds an alarm is triggered.
If, for safety reasons, you wish to switch off the corresponding control in the event of an
alarm, then check Deactivate control during alarm.
6 Control
Depending on the differences between the desired Nominal values and the measured actual
values (= control differences), measures can be taken that raise or lower these values.
The control is either via the influence of one or more dosing pumps and/or via switching of
sockets. Set the desired nominal values and chose one or more control methods.
EN 2022-01-31 32
Instruction Manual ION Director®
This control method is explained in more detail in the corresponding Knowledge Base article,
which you can find on our website www.aquariumcomputer.com.
7 Measurement accuracy
The ION Director® gives you the best possible accuracy for a measuring device of this class.
In many trials, the measurement process, the measurement electronics and the mechanical
design have been optimized to such an extent that the ION Director® can supply very precise
measurement results. Nevertheless, small measuring tolerances, as they occur in all
measuring devices, cannot be completely avoided.
You as a user can make a significant contribution to achieving the maximum measurement
accuracy the ION Director® can offer by ensuring the following optimal starting conditions:
For details on the duration and accuracy of the measurement as well as the consumption of
references and sample water, please refer to 11 Technical Data.
EN 2022-01-31 33
Instruction Manual ION Director®
• Many commonly used measuring methods, e.g. test kits, offer at best a reproducibility
of 5% under real conditions, an actual tolerance of 10% or more is not uncommon.
• When regulating the individual parameters, it is not important that a specific value is
permanently maintained to the ppm level; rather, it is important that the parameters
are within an optimal range.
In most cases, even several successive measurements with the same equipment show more
or less deviating results. It is therefore difficult to judge which result is the "correct" one.
This is where the ION Director® shows another strength: The measurement process is always
exactly the same, the results are calculated exactly according to scientific principles and are
more reproducible than with most other methods.
7.3 Conclusion
Every measurement is subject to tolerances, yet the ION Director® delivers a high degree of
precision when used with care.
For effective measurement and control (if used), we recommend the following:
1. ensure that the measurement achieves reasonable accuracy with appropriate effort.
2. adjust the control for each parameter (or manually dose in such a way) that the
desired optimum ranges are maintained.
3. do not select these ranges too narrowly.
8 Maintenance
The ION Director® is largely maintenance-free. It is recommended to clean the device from
dust and other contaminants.
Tubes, pumps and motors are wearing parts, the service life depends on the frequency
of use, the flow rates and the ambient conditions.
In the event of malfunction (for example, inadequate fluid delivery, loss of suction, leakage,
increased operating noise) or mechanical failure, these must be replaced.
Due to the maintenance-friendly design, all wear parts can be easily replaced by yourself, all
wearing parts are available as accessories.
EN 2022-01-31 34
Instruction Manual ION Director®
9 Warranty/Liability
You have a 2-year warranty beginning from invoice date. This applies to material and
manufacturing defects (normal wear and tear, such as occurs with sensors, is not subject to
the warranty).
We guarantee that the supplied products correspond to the specifications and that the
products do not have material resp. manufacturing defects. For the accuracy of the manuals,
we do not guarantee damages of any kind which result from improper operation or from an
unsuitable environment. Furthermore, we do not take over warranty for damages that are
caused by a false connection or excessive humidity. We assume no liability for direct
damages, indirect damages, consequential damages and third-party damages as far as it is
legally permitted. We do not take over guarantee that our product package corresponds to
the requirements of the buyer. Our warranty expires if the delivered original product is
damaged or modified.
10 Additional Information
10.1 Help and Information
Help and further information can be found on our website www.aquariumcomputer.com
(where you can use our Knowledge Base, our Download Area and our Support Forum, among
other things, free of charge), or from the dealer from whom you purchased the device.
10.2 Firmware-Update
DANGER
• Be sure to back up your data before updating!
The firmware of your GHL Devices is constantly being further developed. If you want to use
new features that are not supported by your current firmware, you can update your device.
For the update, you need the PC program GHL Control Center, which can be downloaded free
of charge from our website www.aquariumcomputer.com.
EN 2022-01-31 35
Instruction Manual ION Director®
EN 2022-01-31 36
Instruction Manual ION Director®
11 Technical Data
Input voltage 24 VDC
EN 2022-01-31 37