Professional Documents
Culture Documents
SM 66
SM 66
The battery, starting, and charging systems in the vehicle operate with one another and must be tested as a
complete system. In order for the engine to start and the battery to maintain its charge properly, all of the
components that are used in these systems must perform within specifications. It is important that the battery,
starting, and charging systems be thoroughly tested and inspected any time a battery needs to be charged or
replaced. The cause of abnormal battery discharge, overcharging or early battery failure must be diagnosed and
corrected before a battery is replaced and before a vehicle is returned to service. The service information for
these systems has been separated within this service information to make it easier to locate the specific
information you are seeking. However, when attempting to diagnose any of these systems, it is important that
you keep their interdependency in mind.
The diagnostic procedures used for the battery, starting, and charging systems include the most basic
conventional diagnostic methods, to the more sophisticated On-Board Diagnostics (OBD) built into the
Powertrain Control Module (PCM). Use of an induction-type milliampere ammeter, a volt/ohmmeter, a battery
charger, a carbon pile rheostat (load tester) and a 12-volt test lamp may be required. All OBD-sensed systems
are monitored by the PCM. Each monitored circuit is assigned a Diagnostic Trouble Code (DTC). The PCM
will store a DTC in electronic memory for any inoperative system it detects. For the proper charging system on-
board diagnostic test procedures, refer to DIAGNOSIS AND TESTING .
The Micro 420 automotive battery system tester is designed to help diagnose the cause of a defective battery.
For directions on using the Micro 420 battery tester. Refer to BATTERY, STANDARD PROCEDURE.
SPECIFICATIONS
SPECIFICATIONS
The battery Group Size number, the Cold Cranking Amperage (CCA) rating, and the Reserve Capacity (RC)
rating or Ampere-Hours (AH) rating can be found on the original equipment battery label. Be certain that a
replacement battery has the correct Group Size number, as well as CCA, and RC or AH ratings that equal or
exceed the original equipment specification for the vehicle being serviced. Battery sizes and ratings are
discussed in more detail below.
Group Size - The outside dimensions and terminal placement of the battery conform to standards
established by the Battery Council International (BCI). Each battery is assigned a BCI Group Size
number to help identify a correctly-sized replacement.
Cold Cranking Amperage - The Cold Cranking Amperage (CCA) rating specifies how much current (in
amperes) the battery can deliver for thirty seconds at -18° C (0° F). Terminal voltage must not fall below
7.2 volts during or after the thirty second discharge period. The CCA required is generally higher as
engine displacement increases, depending also upon the starter current draw requirements.
Reserve Capacity - The Reserve Capacity (RC) rating specifies the time (in minutes) it takes for battery
terminal voltage to fall below 10.5 volts, at a discharge rate of 25 amperes. RC is determined with the
battery fully-charged at 26.7° C (80° F). This rating estimates how long the battery might last after a
charging system failure, under minimum electrical load.
Ampere-Hours - The Ampere-Hours (AH) rating specifies the current (in amperes) that a battery can
deliver steadily for twenty hours, with the voltage in the battery not falling below 10.5 volts. This rating
is also sometimes identified as the twenty-hour discharge rating.
Load Test Amperage - The Load Test Amperage rating specifies the current (in amperes) that a battery
should be tested at with the battery load test equipment. This value should always be 50 percent of the
CCA. For example: if the CCA for this battery is 600 amps, the Load Test Amperage is 50 percent of that
or 300 amps.
CLEANING
CLEANING
The following information details the recommended cleaning procedures for the battery and related
components. In addition to the maintenance schedules, it is recommended that these procedures be performed
any time the battery or related components must be removed for vehicle service. Refer to MAINTENANCE
SCHEDULES, DESCRIPTION .
Fig. 1: Cleaning Battery Cable Terminal Clamps
Courtesy of CHRYSLER GROUP, LLC
1. Clean the battery cable terminal clamps (2) of all corrosion. Remove any corrosion using a wire brush or
a post and terminal cleaning tool (1), and a sodium bicarbonate (baking soda) and warm water cleaning
solution.
2. Clean the battery tray and battery hold-down hardware of all corrosion. Remove any corrosion using a
wire brush and a sodium bicarbonate (baking soda) and warm water cleaning solution. Paint any exposed
bare metal.
5. Clean any corrosion from the battery terminal posts with a wire brush or a post and terminal cleaner (1),
and a sodium bicarbonate (baking soda) and warm water cleaning solution.
INSPECTION
INSPECTION
The following information details the recommended inspection procedures for the battery and related
components. In addition to the maintenance schedules. Refer to MAINTENANCE SCHEDULES,
DESCRIPTION . It is recommended that these procedures be performed any time the battery or related
components must be removed for vehicle service.
1. Inspect the battery cable terminal clamps for damage. Replace any battery cable that has a damaged or
deformed terminal clamp.
2. Inspect the battery tray and battery hold down hardware for damage. Replace any damaged parts.
3. Slide the thermal guard off of the battery case (if equipped). Inspect the battery case for cracks or other
damage that could result in electrolyte leaks. Also, check the battery terminal posts for looseness.
Batteries with damaged cases or loose terminal posts must be replaced.
4. Inspect the battery thermal guard (if equipped) for tears, cracks, deformation or other damage. Replace
any battery thermal guard that has been damaged.
5. If the battery is discharged, charge as required. For the proper battery charging procedures, refer to
BATTERY, STANDARD PROCEDURE.
BATTERY
DIAGNOSIS AND TESTING
The Midtronics GR8 battery tester is designed to help diagnose the cause of an inoperative battery. For
instructions on the use of the Midtronics GR8 battery tester, refer to BATTERY, STANDARD
PROCEDURE.
A battery that will not accept a charge is inoperative, and must be replaced. Further testing is not required. A
fully-charged battery must be load tested to determine its cranking capacity. A battery that is fully-charged, but
does not pass the load test, is inoperative and must be replaced.
NOTE: Completely discharged batteries may take several hours to accept a charge. For
the proper battery charging procedures, refer to STANDARD PROCEDURE.
STANDARD PROCEDURE
BATTERY CHARGING
Battery charging is the means by which the battery can be restored to its full voltage potential. A battery is
fully-charged when:
Midtronics (special tool #GR8-1220KIT-CHRY, AGM Battery Tester/Charger Station) tester indicates
battery is OK.
All of the battery cells are gassing freely during battery charging.
Open-circuit voltage of the battery is 12.65 volts or above.
WARNING: Never exceed twenty amperes when charging a cold (-1° C [30° F] or
lower) battery. The battery may arc internally and explode. Personal injury
and/or vehicle damage may result.
WARNING: If the battery shows signs of freezing, leaking, loose posts, do not test,
assist-boost, or charge. The battery may arc internally and explode.
Personal injury and/or vehicle damage may result.
WARNING: Explosive hydrogen gas forms in and around the battery. Do not smoke,
use flame, or create sparks near the battery. Personal injury and/or
vehicle damage may result.
WARNING: The battery contains sulfuric acid, which is poisonous and caustic. Avoid
contact with the skin, eyes, or clothing. In the event of contact, flush with
water and call a physician immediately. Keep out of the reach of children.
WARNING: If the battery is equipped with removable cell caps, be certain that each of
the cell caps is in place and tight before the battery is returned to service.
Personal injury and possible vehicle damage may result from loose or
missing cell caps.
CAUTION: Always disconnect and isolate the battery negative cable before charging
a battery. Do not exceed sixteen volts while charging a battery. Damage to
the vehicle electrical system components may result.
CAUTION: Battery electrolyte will bubble inside the battery case during normal
battery charging. Electrolyte boiling or being discharged from the battery
vents indicates a battery overcharging condition. Immediately reduce the
charging rate or turn off the charger to evaluate the battery condition.
Damage to the battery may result from overcharging.
CAUTION: The battery should not be hot to the touch. If the battery feels hot to the
touch, turn off the charger and let the battery cool before continuing the
charging operation. Damage to the battery may result.
After the battery has been charged to 12.65 volts or greater, perform a load test to determine the battery
cranking capacity. For the proper battery load test procedures, refer to BATTERY, STANDARD
PROCEDURE. If the battery will endure a load test, return the battery to service. If the battery will not endure
a load test, it is inoperative and must be replaced.
Clean and inspect the battery hold-down, tray, terminals, posts, and top before completing battery service. For
the proper battery system cleaning and inspection procedures, refer to CLEANING and INSPECTION.
The following procedure should be used to recharge a completely discharged battery. Unless this procedure is
properly followed, a good battery may be needlessly replaced.
1. Measure the voltage at the battery posts with a voltmeter, accurate to 1/10 (0.10) volt. If the reading is
below ten volts, the battery charging current will be low. It could take some time before the battery
accepts a current greater than a few milliamperes. Such low current may not be detectable on the
ammeters built into many battery chargers.
2. Disconnect and isolate the battery negative cable. Connect the Midtronics (special tool #GR8-1220KIT-
CHRY, AGM Battery Tester/Charger Station).
NOTE: Some battery chargers are equipped with polarity-sensing circuitry. This
circuitry protects the battery charger and the battery from being damaged
if they are improperly connected. If the battery state-of-charge is too low
for the polarity-sensing circuitry to detect, the battery charger will not
operate. This makes it appear that the battery will not accept charging
current. See the instructions provided by the manufacturer of the battery
charger for details on how to bypass the polarity-sensing circuitry.
3. Battery chargers vary in the amount of voltage and current they provide. The amount of time required for
a battery to accept measurable charging current at various voltages is shown in the Charge Rate Table. If
the charging current is still not measurable at the end of the charging time, the battery is inoperative and
must be replaced. If the charging current is measurable during the charging time, the battery may be good
and the charging should be completed in the normal manner.
The time required to charge a battery will vary, depending upon the following factors:
Battery Capacity - A completely discharged heavy-duty battery requires twice the charging time of a
small capacity battery.
Temperature - A longer time will be needed to charge a battery at -18° C (0° F) than at 27° C (80° F).
When a fast battery charger is connected to a cold battery, the current accepted by the battery will be very
low at first. As the battery warms, it will accept a higher charging current rate (amperage).
Charger Capacity - A battery charger that supplies only five amperes will require a longer charging
time. A battery charger that supplies twenty amperes or more will require a shorter charging time.
State-Of-Charge - A completely discharged battery requires more charging time than a partially
discharged battery. Electrolyte is nearly pure water in a completely discharged battery. At first, the
charging current (amperage) will be low. As the battery charges, the specific gravity of the electrolyte
will gradually rise.
The Battery Charging Time Table gives an indication of the time required to charge a typical battery at room
temperature based upon the battery state-of-charge and the charger capacity.
Always use the Midtronics GR8 Instruction Manual that was supplied with the tester as a reference. If the
Instruction Manual is not available the following procedure can be used:
WARNING: Always wear appropriate eye protection and use extreme caution when
working with batteries.
BATTERY TESTING
1. If testing the battery OUT-OF-VEHICLE, clean the battery terminals with a wire brush before testing.
Refer to CLEANING. If the battery is equipped with side post terminals, install and tighten the supplied
lead terminal stud adapters. Do not use steel bolts. Failure to properly install the stud adapters, or using
stud adapters that are dirty or worn-out may result in false test readings.
2. If testing the battery IN-THE-VEHICLE, make certain all of the vehicle accessory loads are OFF,
including the ignition. Connect the Midtronics GR8 directly to the battery posts.
NOTE: Multiple batteries connected in parallel must have the ground cable
disconnected to perform a battery test. Failure to disconnect may result in
false battery test readings.
3. Using the ARROW key select in or out of vehicle testing and press ENTER to make a selection.
4. If not selected, choose the Cold Cranking Amp (CCA) battery rating. Or select the appropriate battery
rating for your area (see menu). The tester will then run its self programmed test of the battery and
display the results. Refer to the test result table noted below.
5. While viewing the battery test result, press the CODE button and the tester will prompt you for the last 4
digits of the VIN. Use the UP/DOWN arrow buttons to scroll to the correct character; then press ENTER
to select and move to the next digit. Then press the ENTER button to view the SERVICE CODE.
Pressing the CODE button a second time will return you to the test results.
NOTE: The SERVICE CODE is required on every warranty claim submitted for battery
replacement.
Inspect the battery for damages and check the electrolyte level. Always use the necessary safety precautions
when working with batteries to prevent severe injury or death. Follow all manufacturers' instructions and BCI
(Battery Council International) safety recommendations, which include the following precautions:
MAIN MENU
The Main Menu is the starting point for all tools and utilities, which are depicted as icons. Some icons lead
directly to the function they represent, while others are menu icons that lead to two or more options.
Automatically tests, charges, and provides battery decision using the information you select in a series of
screens. Start here to generate warranty codes.
Fig. 5: Battery Tester Main Menu Icon 2
Courtesy of CHRYSLER GROUP, LLC
Maintains battery voltage at 13.5 volts to provide uninterrupted reprogramming of ECUs and retain vehicle
system settings.
Fig. 7: Battery Tester Main Menu Icon 4
Courtesy of CHRYSLER GROUP, LLC
Includes a utility to view and print a test counter, a data transfer utility, the software version and date, the
Midtronics GR8 serial number for the control module, and current wireless channel.
The Setup Menu lets you customize options in the Midtronics GR8 to suit your needs.
Fig. 9: Battery Tester Main Menu Icon 6
Courtesy of CHRYSLER GROUP, LLC
Provides a list of topics and definitions. Also includes Midtronics Customer Service phone numbers.
CHARGE/TEST MENU
Automatically tests and charges battery, starting, and charging system. Generates a warranty code for Replace
and Bad Cell decisions.
Fig. 11: Charge/Test Menu Icon 2
Courtesy of CHRYSLER GROUP, LLC
Pre Delivery Inspection (PDI): For testing delivered vehicles and lot maintenance. Uses the same inputs as a
diagnostic charge.
Dual Battery Charge mode allows the charger to be used with dual battery systems.
Fig. 13: Charge/Test Menu Icon 4
Courtesy of CHRYSLER GROUP, LLC
Makes high output current available to boost charge an in-vehicle battery and assist in starting the engine.
Provides a timed charge that ranges from 5 to 120 minutes or a continuous charge that ends when you press the
STOP key.
Fig. 15: Charge/Test Menu Icon 6
Courtesy of CHRYSLER GROUP, LLC
In this mode the charger can provide a trickle charge for long term, low amp battery charging.
Generates 15-digit warranty codes for physically defective batteries or customer good will.
Fig. 17: GR8 Battery Tester
Courtesy of CHRYSLER GROUP, LLC
1. Control module: Backlit graphical display and keypad for data entry.
2. ON/OFF switch: ON/OFF switch Turns power on and off to the GR8.
3. STATUS light: Lights in conjunction with beeping alarm to indicate transitions and warnings.
4. Data card slot: For future upgrades via a data card. The slot contains a plastic filler card for protection.
BATTERY DECISIONS
1. Battery Decisions
2. Select Rating
3. Measured capacity
4. Measured voltage
5. Good Range
NOTE: The warranty code screen will only be displayed for REPLACE BATTERY
and BAD CELL-REPLACE decisions.
A REPLACE BATTERY or BAD CELL-REPLACE decision gives you the option of generating a warranty
code. For Chrysler vehicles model year 2011 or later, enter that warranty code into your wiTECH in the
Midtronics warranty code validation routine.
A battery open-circuit voltage (no load) test will show the approximate state-of-charge of a battery. This test
can be used in place of the hydrometer test when a hydrometer is not available, or for maintenance-free batteries
with non-removable cell caps.
Before proceeding with this test, completely charge the battery. Refer to BATTERY, STANDARD
PROCEDURE.
1. Before measuring the open-circuit voltage, the surface charge must be removed from the battery. Turn on
the headlamps for fifteen seconds, then allow up to five minutes for the battery voltage to stabilize.
2. Disconnect and isolate both battery cables, negative cable first.
3. Using a voltmeter connected to the battery posts measure the open-circuit voltage.
Refer to the Open-Circuit Voltage Table below. This voltage reading will indicate the battery state-of-charge,
but will not reveal its cranking capacity. If a battery has an open-circuit voltage reading of 12.4 volts or greater,
it may be load tested to reveal its cranking capacity. Refer to BATTERY, STANDARD PROCEDURE.
The term Ignition-Off Draw (IOD) identifies a normal condition where power is being drained from the battery
with the ignition switch in the Off position. A normal vehicle electrical system will draw from five to thirty-five
milliamperes (0.005 to 0.035 ampere) with the ignition switch in the Off position, and all non-ignition
controlled circuits in proper working order. Up to thirty-five milliamperes are needed to enable the memory
functions for the Powertrain Control Module (PCM), digital clock, electronically tuned radio, and other
modules which may vary with the vehicle equipment.
A vehicle that has not been operated for approximately twenty days, may discharge the battery to an inadequate
level. When a vehicle will not be used for twenty days or more (stored), remove the IOD fuse from the Totally
Integrated Power Module (TIPM). This will reduce battery discharging.
If the IOD is over thirty-five milliamperes, the problem must be found and corrected before replacing a battery.
In most cases, the battery can be charged and returned to service after the excessive IOD condition has been
corrected.
1. Verify that all electrical accessories are off. Turn off all lamps, remove the ignition key, and close all
doors. If the vehicle is equipped with an illuminated entry system or an electronically tuned radio, allow
the electronic timer function of these systems to automatically shut off (time out). This may take up to ten
minutes. Refer to the Electronic Module Ignition-Off Draw Table for more information.
2. Determine that the underhood lamp is operating properly, then disconnect the lamp wire harness
connector or remove the lamp bulb.
3. Turn off all electrical accessories.
4. Disconnect the battery negative cable.
WARNING: Do not open any doors, or turn on any electrical accessories. Failure
to do so can result in possible serious or fatal injury.
CAUTION: Do not open any doors, or turn on any electrical accessories with the
lowest milliampere scale selected, or the multi-meter may be
damaged.
5. Connect a 10 amp fused jumper wire between the negative battery cable and the negative battery post.
6. Turn the ignition key ON and then OFF and wait 10 minutes for all systems to enter sleep mode.
NOTE: Do not break the connection between the 10 amp fused jumper wire and
the battery. If the connection between the battery negative terminal post
and the negative cable terminal clamp is lost during any part of the IOD
test, the electronic timer function will be activated and all of the tests will
have to be repeated.
7. Set an electronic digital multi-meter to its highest amperage scale. Connect the multi-meter to the battery
negative cable terminal clamp and the battery negative terminal post, but not on the jumper connection.
8. Remove the 10 amp jumper wire without breaking the digital multi-meter connection.
9. The multi-meter leads must be securely clamped to the battery negative cable terminal clamp and the
battery negative terminal post, but not the 10 amp jumper wire.
10. The high-amperage IOD reading on the multi-meter should be very low or nonexistent, depending upon
the electrical equipment in the vehicle. If the amperage reading remains high, remove and replace each
fuse or circuit breaker in the TIPM, one at a time until the amperage reading becomes very low, or
nonexistent. Refer to the appropriate wiring information for complete TIPM, circuit breaker, and circuit
identification. This will isolate each circuit and identify the circuit that is the source of the high-amperage
IOD. If the amperage reading remains high after removing and replacing each fuse, disconnect the wire
harness from the generator. If the amperage reading now becomes very low or nonexistent, diagnose and
repair the Charging System as necessary. After the high-amperage IOD has been corrected, switch the
multi-meter to progressively lower amperage scales and, if necessary, repeat the fuse and circuit breaker
remove-and-replace process to identify and correct all sources of excessive IOD. It is now safe to select
the lowest milliampere scale of the multi-meter to check the low-amperage IOD.
11. Observe the multi-meter reading. The low-amperage IOD should not exceed thirty-five milliamperes
(0.035 ampere). If the current draw exceeds thirty-five milliamperes, isolate each circuit using the fuse
and circuit breaker remove-and-replace process in. Refer to 10. The multi-meter reading will drop to
within the acceptable limit when the source of the excessive current draw is disconnected. Repair this
circuit as required; whether a wiring short, incorrect switch adjustment, or an inoperative component is
the cause.
REMOVAL
REMOVAL
WARNING: Wear a suitable pair of rubber gloves (not the household type) when
removing a battery by hand. Safety glasses should also be worn. If the
battery is cracked or leaking, the electrolyte can burn the skin and eyes.
1. Turn the ignition switch to the Off position. Be certain that all electrical accessories are turned off.
2. Disconnect the battery negative cable from the battery.
3. Disconnect the battery positive cable from the battery.
4. Remove the battery thermal cover (1).
5. Remove the battery hold down retaining bolt (2) and battery hold down (3).
6. Remove the battery (4) from the battery tray.
INSTALLATION
INSTALLATION
1. Clean and inspect the battery (2). For the proper procedures, refer to CLEANING and INSPECTION.
CAUTION: Be certain that the battery cable terminal clamps are connected to the
correct battery terminal posts. Reversed battery polarity may damage
electrical components of the vehicle.
2. Position the battery into the battery tray. Ensure that the battery positive and negative terminal posts are
correctly positioned. The battery cable terminal clamps must reach the correct battery terminal post
without stretching the cables.
3. Position the battery hold down (3) and install the retaining bolt (2).
4. Clean the battery cable terminal clamps and the battery terminal posts. For the proper procedures, refer to
CLEANING.
5. Connect the battery positive cable to the battery. Tighten to 4 N.m (35 in. lbs.).
6. Connect the battery negative cable to the battery. Tighten to 4 N.m (35 in. lbs.).
7. Apply a thin coating of petroleum jelly or chassis grease to the exposed surfaces of the battery cable
terminal clamps and the battery terminal posts.
8. Obtain an appropriate scan tool and check the PCM for any stored battery disconnect trouble codes. Clear
codes if required.
CABLES, BATTERY
DIAGNOSIS AND TESTING
A voltage drop test will determine if there is excessive resistance in the battery cable terminal connections or
the battery cables. If excessive resistance is found in the battery cable connections, the connection point should
be disassembled, cleaned of all corrosion or foreign material, then reassembled. Following reassembly, check
the voltage drop for the battery cable connection and the battery cable again to confirm repair.
When performing the voltage drop test, it is important to remember that the voltage drop is giving an indication
of the resistance between the two points at which the voltmeter probes are attached. EXAMPLE: When testing
the resistance of the battery positive cable, touch the voltmeter leads to the battery positive cable terminal clamp
and to the battery positive cable eyelet terminal at the starter solenoid B(+) terminal stud. If you probe the
battery positive terminal post and the battery positive cable eyelet terminal at the starter solenoid B(+) terminal
stud, you are reading the combined voltage drop in the battery positive cable terminal clamp-to-terminal post
connection and the battery positive cable.
TESTING
The following operation will require a voltmeter accurate to 1/10 (0.10) volt. Before performing this test, be
certain that the following procedures are accomplished:
1. Connect the positive lead of the voltmeter (1) to the battery negative terminal post. Connect the negative
lead of the voltmeter to the battery negative cable terminal clamp. Rotate and hold the ignition switch in
the Start position. Observe the voltmeter. If voltage is detected, correct the poor connection between the
battery negative cable terminal clamp and the battery negative terminal post.
NOTE: If the vehicle is equipped with two 12v batteries, step #1 must be
performed twice, once for each battery.
2. Connect the positive lead of the voltmeter (1) to the battery positive terminal post. Connect the negative
lead of the voltmeter to the battery positive cable terminal clamp. Rotate and hold the ignition switch in
the Start position. Observe the voltmeter. If voltage is detected, correct the poor connection between the
battery positive cable terminal clamp and the battery positive terminal post.
NOTE: If the vehicle is equipped with two 12v batteries, step #2 must be
performed twice, once for each battery.
Fig. 25: Checking Voltage Between Battery & Starter
Courtesy of CHRYSLER GROUP, LLC
3. Connect the voltmeter (2) to measure between the battery positive cable terminal clamp (1) and the starter
solenoid (3) B(+) terminal stud. Rotate and hold the ignition switch in the Start position. Observe the
voltmeter. If the reading is above 0.2 volt, clean and tighten the battery positive cable eyelet terminal
connection at the starter solenoid B(+) terminal stud. Repeat the test. If the reading is still above 0.2 volt,
replace the faulty battery positive cable.
NOTE: If the vehicle is equipped with two 12v batteries, step #3 must be
performed twice, once for each battery.
4. Connect the voltmeter (1) to measure between the battery (2) negative cable terminal clamp and a good
clean ground on the engine block (3). Rotate and hold the ignition switch in the Start position. Observe
the voltmeter. If the reading is above 0.2 volt, clean and tighten the battery negative cable eyelet terminal
connection to the engine block. Repeat the test. If the reading is still above 0.2 volt, replace the faulty
battery negative cable.
NOTE: If the vehicle is equipped with two 12v batteries, step #4 must be
performed twice, once for each battery.
REMOVAL
REMOVAL
NEGATIVE
1. Turn the ignition switch to the Off position. Be certain that all electrical accessories are turned off.
2. Disconnect and isolate the battery negative cable terminal clamp (3).
3. Remove the bolt (4) securing the negative cable to the left front fender.
Fig. 28: Removing/Installing Negative Battery Cable
Courtesy of CHRYSLER GROUP, LLC
4. One at a time, trace the battery cable retaining pushpins (3), fasteners and routing clips until the cable is
free from the vehicle.
5. Remove the bolt (4) securing the negative cable to the engine.
6. Remove the bolt (6) securing the negative cable to the left frame rail.
7. Remove the battery negative cable from the vehicle.
POSITIVE
10. Remove the nut (5) securing the cable to the starter solenoid (6).
11. Lower the vehicle.
12. Lift the terminal cap (4) and remove the nut (3) securing the cable (1) to the alternator (2).
13. Disconnect any remaining pushpins securing the cable to the vehicle.
14. Remove the battery positive cable from the vehicle.
INSTALLATION
INSTALLATION
NEGATIVE
Fig. 32: Removing/Installing Negative Battery Cable
Courtesy of CHRYSLER GROUP, LLC
5. Install the bolt (4) securing the negative cable (3) to the left front fender.
6. Connect the battery negative cable terminal clamp (3).
7. Check the vehicle for normal operation.
POSITIVE
7. Connect the battery cable retaining pushpins (1) securing the cable to the left frame rail.
8. Lower the vehicle.
Fig. 37: Identifying Battery Cables & Components
Courtesy of CHRYSLER GROUP, LLC
9. Install the battery cable retaining pushpin (8) securing the cable to the battery tray.
10. Install the wire harness connector (7) pushpin into the Totally Integrated Power Module (TIPM) (5)
housing.
11. Connect the wire harness connector (6) at the TIPM.
12. Install the nut (9) securing the cable to the TIPM.
13. Connect the battery positive cable terminal clamp (1).
14. Connect the battery negative cable terminal clamp (3).
15. Check the vehicle for normal operation.
RETAINER, BATTERY
REMOVAL
REMOVAL
CAUTION: Never operate a vehicle without a battery hold down device properly
installed. Damage to the vehicle, components and battery could result.
1. Verify that the ignition switch and all accessories are OFF.
2. Disconnect and isolate the battery negative cable.
3. Remove the bolt (6) from the battery hold down bracket (5) and remove the bracket from the vehicle.
INSTALLATION
INSTALLATION
1. Clean and inspect the battery hold down bracket (5) and bolt (6). Refer to CLEANING.
2. Position the battery hold down bracket in the battery tray.
CAUTION: Be certain that the hold down bracket is properly positioned in the
battery tray before tightening the hold down bolt or damage to the
battery and tray may result.
TRAY, BATTERY
REMOVAL
REMOVAL
Fig. 40: Removing/Installing Battery Tray (Left Side) 1 Of 2
Courtesy of CHRYSLER GROUP, LLC
1. Remove the battery (3) from the battery tray. Refer to BATTERY, REMOVAL.
2. Remove the Totally Integrated Power Module (TIPM) (5). Refer to MODULE, TOTALLY
INTEGRATED POWER (TIPM), REMOVAL .
3. Disconnect the wire harness retainers from the battery tray assembly.
4. Disconnect the purge solenoid (6) from its mounting bracket.
5. Remove the anti-lock brake controller (if equipped) retaining bolts and support the brake controller with
mechanics wire. It is not necessary to completely remove the anti-lock brake control unit.
6. Remove the left front wheelhouse splash shield. Refer to SHIELD, SPLASH, FRONT
WHEELHOUSE, REMOVAL .
Fig. 41: Removing/Installing Battery Tray (Left Side) 2 Of 2
Courtesy of CHRYSLER GROUP, LLC
7. Mark the location of the cruise servo (3) (if equipped) and remove the retaining screws. Position the servo
out of the way.
8. Disconnect the left front fender ground wire.
9. Remove the remaining battery tray retaining bolts (2).
10. Remove the battery tray from the vehicle.
INSTALLATION
INSTALLATION
Fig. 42: Removing/Installing Battery Tray (Left Side) 2 Of 2
Courtesy of CHRYSLER GROUP, LLC
1. Position the battery tray assembly (1) and install the retaining bolts (2).
2. Connect the left front fender ground wire.
3. Install the cruise servo (3) (if equipped) and retaining screws.
4. Install the left front wheelhouse splash shield. Refer to SHIELD, SPLASH, FRONT WHEELHOUSE,
INSTALLATION .