LOCTITE SI 5331 en - GL

Technical Data Sheet
LOCTITE® SI 5331™
Known as LOCTITE® 5331
June-2022
PRODUCT DESCRIPTION (lb.in) (13.3)

LOCTITE® SI 5331™ provides the following product Prevail Torque, ISO 10964:
characteristics: M10 steel nuts and bolts N·m 0.5
(lb.in) (4.42)
Technology Silicone Breakloose Torque, ISO 10964, Pre-torqued to 5 N·m:
Chemical Type Acetoxy silicone M10 steel nuts and bolts N·m 4.5
Appearance (uncured) White paste (lb.in) (39.8)
Components One component - Max. Prevail Torque, ISO 10964, Pre-torqued to 5 N·m:
requires no mixing M10 steel nuts and bolts N·m 1.0
Viscosity Medium (lb.in) (8.85)
Cure Humidity
Application Thread sealing
Strength Low
TYPICAL ENVIRONMENTAL RESISTANCE
LOCTITE® SI 5331™ is recommended for use on plastic pipe The low strength of this sealant is maintained at temperatures
threaded fittings carrying hot or cold water. This product cures up to 150 °C
at ambient temperatures under the influence of atmospheric
moisture to form a low strength flexible seal against hot and Sealing capability is maintained up to 0.3 MPa in water @ 90
°C. Tests on steel fittings using water/glycol maintained seals
cold water. cycling 20 to 90 °C for 12 months without leaking.
NSF International
Registered to NSF Category P1 for use as a sealant where there is
GENERAL INFORMATION
no possibility of food contact in and around food processing areas. This product is not recommended for use in pure oxygen
Note: This is a regional approval. Please contact your local Technical and/or oxygen rich systems and should not be selected as
Service Center for more information and clarification. a sealant for chlorine or other strong oxidizing materials.
For safe handling information on this product, consult the
TYPICAL PROPERTIES OF UNCURED MATERIAL Safety Data Sheet (SDS).
Specific Gravity @ 25 °C 1.1
Directions for use
Flash Point - See SDS
1. Apply the product to the threaded parts (these may be
Viscosity, Brookfield - RVT,25°C,mPa·s (cP): to,"as received" parts or parts cleaned with a damp cloth
Spindle 7,, speed 10 rpm 50,000 or paper towel).
2. Product should be applied to both male and female
threads and then worked into the threads to ensure good
Instant Sealing Capability wetting.
The cure speed of this product is independent of substrates but 3. For potable water systems, allow product to cure for 96
requires atmospheric humidity 40% minimum to develop full hours at 20 to 23°C prior to use.
sealing capability (0.3 MPa) within 12 hours. Instant seal
Not for product specifications
capability is 0.05 MPa water pressure as measured on 25.4
The technical data contained herein are intended as reference
mm fittings. Low temperatures do not reduce the effectiveness
only. Please contact your local quality department for
of this sealant unless the atmospheric moisture is also low.
assistance and recommendations on specifications for this
TYPICAL CURING PERFORMANCE product.
Open Time Storage

Open Time @ 25°C, minutes 5 Store product in the unopened container in a dry location.
Storage information may be indicated on the product container
labeling.
Optimal Storage: 8 °C to 21 °C. Storage below 8 °C or
TYPICAL PERFORMANCE OF CURED MATERIAL greater than 28 °C can adversely affect product properties.
Adhesive Properties Material removed from containers may be contaminated during
use. Do not return product to the original container. Henkel
After 72 hours @ 22°C
Corporation cannot assume responsibility for product which
Breakaway Torque, ISO 10964: has been contaminated or stored under conditions other than
M10 steel nuts and bolts N·m 1.5 those previously indicated. If additional information is required,
please contact your local Henkel representative.
For the most direct access to local sales and technical support visit: www.henkel.com/industrial
TDS LOCTITE® SI 5331™, June-2022
Disclaimer
The information provided in this Technical Data Sheet (TDS) including the
recommendations for use and application of the product are based on our
knowledge and experience of the product as at the date of this TDS. The product
can have a variety of different applications as well as differing application and
working conditions in your environment that are beyond our control. Henkel is,
therefore, not liable for the suitability of our product for the production processes
and conditions in respect of which you use them, as well as the intended
applications and results. We strongly recommend that you carry out your own
prior trials to confirm such suitability of our product. Any liability in respect of the
information in the Technical Data Sheet or any other written or oral
recommendation(s) regarding the concerned product is excluded, except if
otherwise explicitly agreed and except in relation to death or personal injury
caused by our negligence and any liability under any applicable mandatory
product liability law.
In case products are delivered by Henkel Belgium NV, Henkel Electronic

Materials NV, Henkel Nederland BV, Henkel Technologies France SAS and
Henkel France SA please additionally note the following:
In case Henkel would be nevertheless held liable, on whatever legal ground,
Henkel’s liability will in no event exceed the amount of the concerned delivery.
In case products are delivered by Henkel Colombiana, S.A.S. the following

disclaimer is applicable:
The information provided in this Technical Data Sheet (TDS) including the
recommendations for use and application of the product are based on our
knowledge and experience of the product as at the date of this TDS. Henkel is,
therefore, not liable for the suitability of our product for the production processes
and conditions in respect of which you use them, as well as the intended
applications and results. We strongly recommend that you carry out your own
prior trials to confirm such suitability of our product.
Any liability in respect of the information in the Technical Data Sheet or any other
written or oral recommendation(s) regarding the concerned product is excluded,
except if otherwise explicitly agreed and except in relation to death or personal
injury caused by our negligence and any liability under any applicable mandatory
product liability law.
In case products are delivered by Henkel Corporation, or Henkel Canada

Corporation, the following disclaimer is applicable:
The data contained herein are furnished for information only and are believed to
be reliable. We cannot assume responsibility for the results obtained by others
over whose methods we have no control. It is the user's responsibility to
determine suitability for the user's purpose of any production methods mentioned
herein and to adopt such precautions as may be advisable for the protection of
property and of persons against any hazards that may be involved in the handling
and use thereof. In light of the foregoing, Henkel Corporation specifically
disclaims all warranties expressed or implied, including warranties of
merchantability or fitness for a particular purpose, arising from sale or use
of Henkel Corporation’s products. Henkel Corporation specifically
disclaims any liability for consequential or incidental damages of any kind,
including lost profits. The discussion herein of various processes or
compositions is not to be interpreted as representation that they are free from
domination of patents owned by others or as a license under any Henkel
Corporation patents that may cover such processes or compositions. We
recommend that each prospective user test his proposed application before
repetitive use, using this data as a guide. This product may be covered by one or
more United States or foreign patents or patent applications.
Trademark usage
Except as otherwise noted, all trademarks in this document are trademarks of
Henkel Corporation in the U.S. and elsewhere. ® denotes a trademark registered
in the U.S. Patent and Trademark Office.
Reference 1.7
For the most direct access to local sales and technical support visit: www.henkel.com/industrial

LOCTITE SI 5331 en - GL

Uploaded by

Copyright:

Available Formats

LOCTITE SI 5331 en - GL

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

LOCTITE SI 5331 en - GL

Uploaded by

Copyright:

Available Formats

Technical Data Sheet

PRODUCT DESCRIPTION (lb.in) (13.3)

Open Time Storage

In case products are delivered by Henkel Belgium NV, Henkel Electronic

In case products are delivered by Henkel Colombiana, S.A.S. the following

In case products are delivered by Henkel Corporation, or Henkel Canada

You might also like