Professional Documents
Culture Documents
Simulation of CCS (MEA Absorption) Using Aspen Plus (Good) - 2019
Simulation of CCS (MEA Absorption) Using Aspen Plus (Good) - 2019
com
ScienceDirect
The 6th International Conference on Power and Energy Systems Engineering (CPESE 2019),
20–23 September 2019, Okinawa, Japan
Abstract
Carbon dioxide emissions to the atmosphere are drastically increased due to fossil fuel-based power plants and different kinds
of industrial processes. Carbon capture is essential to maintain a better environment. Flue gas emissions from the coal-fired
power plant, gas-fired power plant, cement manufacturing industry as well as the aluminium production industry are considered
for the present study. Carbon dioxide capture model is developed and implemented in Aspen Plus to calculate the regeneration
energy requirement. The regeneration energy requirement in the stripping process in the carbon capture is calculated as 3634,
3781, 3229 and 3085 kJ/kg respectively for coal, gas, cement, and aluminium production process flue gas treating.
⃝c 2019 Published by Elsevier Ltd. This is an open access article under the CC BY-NC-ND license
(http://creativecommons.org/licenses/by-nc-nd/4.0/).
Peer-review under responsibility of the scientific committee of the 6th International Conference on Power and Energy Systems Engineering (CPESE
2019).
Keywords: Carbon capture; Aspen plus; Simulation; Regeneration energy; Flue gas
1. Introduction
Carbon dioxide (CO2 ) is known as a greenhouse gas (GHG) which absorb and emit thermal radiation. The CO2
concentration in the atmosphere has rapidly risen after the industrial revolution [1]. CO2 is the main anthropogenic
contributor for greenhouse gas effect as a result of a major contribution to the temperature rising. CO2 is produced in
large quantities by many industries which can be mainly naming as coal and gas-fired power plants, steel production,
cement production, chemical and petrochemical production, etc. [2]. There are several methods that have been
suggested by the scientists, including switching to the green energy (wind power, solar power), improving process
efficiency of the power plants, and capturing CO2 emissions of the power plants and industries [3]. However, the
most realistic option will remain as the carbon capture and storage (CCS) for several decades to maintain the green
environment [4]. CCS technology is not widely applicable due to the high energy consumption of the regeneration
process. The main idea behind this research study is to develop and implement a CO2 capture process model to
minimize the regeneration energy requirement in the CO2 mitigation process.
∗ Corresponding author.
E-mail address: [email protected] (S.P.R.A. Udara).
https://doi.org/10.1016/j.egyr.2019.11.134
2352-4847/⃝ c 2019 Published by Elsevier Ltd. This is an open access article under the CC BY-NC-ND license (http://creativecommons.org/
licenses/by-nc-nd/4.0/).
Peer-review under responsibility of the scientific committee of the 6th International Conference on Power and Energy Systems Engineering
(CPESE 2019).
660 S.P.R.A. Udara, R. Kohilan, M.A.L. Lakshan et al. / Energy Reports 6 (2020) 659–663
The post-combustion chemical absorption process is the most viable technique to capture flue gas carbon dioxide.
The acid gas mainly CO2 can be chemically captured with amine solvents by the post-combustion process. The
captured CO2 with amine solvent can be regenerated to collect as purified CO2 suing steam as the medium for the
regeneration process. However, with the current situation, the main drawback of the technology is the high amount
of energy requirement in the regeneration process. Therefore, reduction of energy requirement in the carbon capture
process is necessary to be implemented in the industries and power plants to achieve a green environment.
2. Model development
The carbon capture model is developed for flue gas stream from 500 MW coal and gas-fired power plants, Cement
industry as well as for aluminium production industry. The conditions of the flue gas stream are given in Table 1,
which is taken from the literature coal-fired power plant [5], Gas fired power plant [6], Cement industry [7], and
Aluminium industry [1].
Aspen Plus rate based model is used to develop the comprehensive process flow sheet (Fig. 1).
The process flow diagram is developed to capture 85% of CO2 from the flue gas stream. Absorber and stripper
are considered as the main two-unit operation blocks in the capture process. Inlet flue gas and the solvent are
supplied at 313 K, and absorption process is performed at 1 bar pressure for optimum operation. The rich solvent
leaving the bottom of the absorber column is heated up to 382 K using a heat exchanger unit before sending it
to the stripper section. The stripper is operating at 2 bar absolute pressure. The solvent stream is selected based
on previous studies [8]. The solvent stream condition which is used to perform the simulation studies is given in
Table 2.
The amine-based carbon capture process is implemented in Aspen Plus process simulation software as shown in
Fig. 1. Monoethanolamine (MEA) is considered as the solvent which is used for the absorption process. The main
drawback of the MEA based carbon capture process is a high amount of energy requirement in the regeneration
process, that is the re-boiler duty in the stripper column. Hence, the optimization of the capture plant is required
to install the carbon capture process in real industrial applications. Absorber and Stripper packing conditions and
operating parameters are selected from literature to perform the simulation studies [9,10]. The most important
parameters are tabulated in Table 3.
There are several simulation models available in the Aspen Plus. Due to several reasons, the Aspen Plus Rad-Frac
model is finally chosen as the best operating model. Rad-Frac is considered as the most active unit operation model
for vapour–liquid absorption and stripping section, faster simulation in comparison with other available options.
Moreover, fewer convergence problems compared to other available options in Aspen Plus with high accuracy. It is
important to select the property method in Aspen Plus to perform the calculation during the simulations [1,9,13].
Each unit operation model requires a property method to perform its calculation routes. Mainly, four different
property methods are available in the Aspen Plus for CO2 +MEA systems, which are:
ELECNRTL-handle both very low and high concentrations of aqueous and mixed solvent systems.
ENTRL-HF-similar to the ELECNRTL property method except that it uses the HF equation of state for vapour
phase calculation model.
ENTRL-HG-similar to the ELECNRTL property method except it uses the Helgeson model for standard property
calculations.
AMINES-this property method uses Kent–Eisenberg correlation for K-values and enthalpy calculation. Out
of them, the ELECNRTL model is selected for the simulation of the CO2 capture process for this study. The
ELECNRTL is the most versatile electrolyte property method as it has the capability of handling both very low and
high concentrations of aqueous and mixed solvent systems.
Hydrolysis reaction:
M E AC O O − + H2 O ↔ M E A + H C O3− (1)
Dissociation of dissolved carbon dioxide:
C O2 + 2H2 O ↔ H C O3− + H3 O + (2)
Dissociation of bicarbonate:
H C O3− + H2 O ↔ H3 O + C O32− (3)
Dissociation of protonated MEA:
M E AH + + H2 O ↔ M E A + H3 O + (4)
Ionization of water:
2H2 O ↔ O H − + H3 O + (5)
The mole fraction of each component is calculated using the above equations. The equilibrium constant which
is required for the calculations have followed Eq. (6),
Bj
ln K j = A j + + C j ln T + D j T (6)
T
According to the literature [15], constants in Eq. (6) which are corresponding to Eqs. (1)–(5) are given in Table 4.
Moreover, the solvent concentration effect on CO2 removal process also considered. It can be clearly seen that,
with the increase of solvent concentration, the required solvent flow rate is gradually decreasing, therefore required
regeneration energy for a stripper is decreasing. However, higher solvent concentration believes to have corrosive
effects in all sections, in the capture plant.
5. Conclusion
This research mainly has focused on process modelling and simulation of CO2 capture with the post-combustion
chemical absorption process. The carbon capture model is developed and implemented in the Aspen Plus process
simulation tool. The main problem of the post-combustion chemical absorption technology is a large amount of
energy requirement in the re-generating sector. Therefore, the reduction of operating cost is important to achieve
the removal process in flue gas treating. The model is developed in Aspen Plus process simulation tool to optimize
the removal process. The Electrolyte NRTL (ELECNRTL) property method is used to handle the chemical reacting
system. There are four different case studies considered for the simulation process which are, coal-fired power plant,
gas-fired power plant, cement plant as well as the aluminium industry. The required re-boiler duty was calculated
for every situation. The required regeneration energy is calculated as 3634, 3781, 3229 and 3085 kJ/kg respectively
for coal, gas, cement and aluminium production process flue gas treating.
References
[1] Udara SPR Arachchige, Dinesh K, Morten CM. Simulation of carbon dioxide capture for aluminium production process. Int J Model
Optim 2014;(4–1):43–50.
[2] Sholeh Ma’mun. Selection and cheracterization of new absorbents for Carbon Dioxide capture (Ph.D thesis), Norway: NTNU; 2005.
[3] Udara SPR Arachchige. Carbon dioxide capture by chemical absorption: energy optimization and analysis of dynamic viscosity of
solvents (Ph.D. thesis), University of South-Eastern Norway; 2019.
[4] Anderson S, Newell R. Prospects for carbon capture and storage technologies. discussion paper. In: Resources for the future. 2003.
[5] Alie CF. Co2 capture with MEA: intergrating the absorption process and steam cycle of an existing coal-fired power plant (Master
thesis), Canada: University of Waterloo; 2004.
[6] Fluor for IEA GHG Program. Improvement in power generation with post-combustion capture of CO2. In: Final report. 2004.
[7] Nazmul HSM. Techno-economic study of CO2 capture process for cement plants. (Master thesis), Ontario, Canada: University of
waterloo; 2005.
[8] Udara SPRA, Muhammad M, Melaaen MC. Optimization of post combustion carbon capture process-solvent selection. Int J Energy
Environ 2012;(3–6):861–70 (submitted for publication).
[9] Aspen Plus. Rate based model of the CO2 capture process by MEA using aspen plus. Cambridge, MA, USA: Aspen Technology Inc;
2008.
[10] Mohammad A. Carbon dioxide capture from flue gas (Ph.D. thesis), Netherland: University of Delft; 2009.
[11] Bravo JL, Rocha JA, Fair JR. Mass transfer in gauze packing. Hydrocarbon Process 1985;January:91–5.
[12] Billet R, Schultes M. Predicting mass transfer in packed columns. Chem Eng Technol 1993;(16):1–9.
[13] Aspen Plus. Aspen physical property methods. Cambridge, MA, USA: Aspen Technology Inc; 2006, p. 61–3.
[14] Freguia S. Modeling of CO2 removal from flue gas with mono-ethanolamine (Master thesis), Austin, USA: University of Texas; 2002.
[15] Liu Y, Zhang L. Watanasiri s. representing vapor-liquid equilibrium for an aqueous MEA-CO2 system using the electrolyte
nonrandom-two-liquid model. Ind Eng Chem Res 1999;38:2080–90.