Bode 100 User Manual ENU10060503
Bode 100 User Manual ENU10060503
User Manual
2 OMICRON Lab
Contents
Contents
1 Safety instructions 10
1.1 Operator qualifications ................................................................................................................ 10
1.2 Rules for use ............................................................................................................................... 11
1.3 Designated use ........................................................................................................................... 11
1.4 Disclaimer ................................................................................................................................... 11
1.5 Cleaning ...................................................................................................................................... 11
2 Compliance statements and recycling 12
2.1 Compliance statement ................................................................................................................ 12
2.2 Information for disposal and recycling ......................................................................................... 12
3 Bode 100 and accessories 13
3.1 Delivered items ........................................................................................................................... 13
3.2 Optional accessories ................................................................................................................... 14
4 Technical data 15
4.1 Absolute maximum ratings .......................................................................................................... 15
4.2 Bode 100 specifications .............................................................................................................. 16
4.3 Power requirements .................................................................................................................... 17
4.4 System requirements .................................................................................................................. 17
4.5 Environmental requirements ....................................................................................................... 18
4.6 Mechanical data .......................................................................................................................... 18
5 Device overview 19
5.1 Connectors .................................................................................................................................. 19
5.2 Block diagram ............................................................................................................................. 21
5.3 Functional description ................................................................................................................. 22
5.4 Hardware revisions ..................................................................................................................... 22
6 Bode Analyzer Suite introduction 23
6.1 Start screen ................................................................................................................................. 23
6.2 Main window ............................................................................................................................... 24
6.2.1 Measurement configuration .......................................................................................... 26
6.2.2 Trace configuration ....................................................................................................... 28
6.2.3 Ribbon controls ............................................................................................................. 30
6.2.4 Status bar ..................................................................................................................... 32
6.3 Chart context menu ..................................................................................................................... 33
6.4 Options menu .............................................................................................................................. 34
6.5 Hardware setup ........................................................................................................................... 37
7 Measurement types and applications 39
7.1 Gain measurement introduction .................................................................................................. 40
7.2 Impedance measurement introduction ........................................................................................ 42
7.3 Vector Network Analysis ............................................................................................................ 46
7.3.1 Transmission / Reflection ............................................................................................ 46
7.3.2 Gain / Phase ................................................................................................................. 52
7.3.3 Reflection with external coupler .................................................................................... 53
7.4 Impedance analysis ................................................................................................................... 54
7.4.1 One-Port ....................................................................................................................... 54
7.4.2 Impedance Adapter ...................................................................................................... 64
7.4.3 Shunt-Thru .................................................................................................................... 69
7.4.4 Shunt-Thru with series resistance ............................................................................... 71
7.4.5 Series-Thru ................................................................................................................... 72
7.4.6 Voltage/Current ............................................................................................................. 73
OMICRON Lab 3
7.4.7 External Bridge ............................................................................................................. 74
8 Calibration 75
8.1 Internal device calibration ........................................................................................................... 75
8.2 Performing a Gain Calibration ..................................................................................................... 76
8.2.1 Calibrating a Transmission (S21) measurement .......................................................... 77
8.2.2 Calibrating a Gain/Phase measurement ....................................................................... 79
8.3 Performing an Impedance Calibration ........................................................................................ 81
8.3.1 Calibrating a Reflection or One-Port Impedance measurement ................................... 84
8.3.2 Calibrating an External Coupler or External Bridge measurement ............................... 86
8.3.3 Calibrating an Impedance Adapter measurement ........................................................ 88
8.3.4 Calibrating a Shunt-Thru or Series-Thru measurement ............................................... 90
8.3.5 Calibrating a Voltage/Current measurement ................................................................ 92
8.4 Further calibration information ................................................................................................... 93
8.4.1 Difference between Full-Range and User-Range calibration ....................................... 93
8.4.2 Enabling and disabling a calibration ............................................................................. 95
8.4.3 Re-performing a calibration .......................................................................................... 96
8.4.4 Full-Range calibration below 10 Hz .............................................................................. 96
8.4.5 Automatic deletion of calibration ................................................................................... 97
8.4.6 Saving calibration data ................................................................................................. 97
9 Bode Analyzer Suite functions 98
9.1 Exporting and saving measurement data or settings .................................................................. 98
9.1.1 Loading and saving the equipment configuration ........................................................ 98
9.1.2 Use the copy to clipboard functions to export data ....................................................... 98
9.1.3 Exporting measurement data to CSV or Excel files ...................................................... 100
9.1.4 Generating a Touchstone file ........................................................................................ 102
9.1.5 Generate a PDF report ................................................................................................. 103
9.2 Signal source settings ................................................................................................................. 104
9.3 Using the interactive chart ........................................................................................................... 107
9.3.1 Configure the diagrams ................................................................................................ 107
9.3.2 Zooming the measurement curve ................................................................................ 109
9.3.3 Optimize the axis scaling ............................................................................................. 112
9.4 Working with cursors and the cursor grid .................................................................................... 115
9.5 Using the memory traces ............................................................................................................ 117
9.6 Using the trace configuration ...................................................................................................... 121
9.7 Cursor calculations ...................................................................................................................... 123
9.7.1 Non-Invasive Stability Measurement ............................................................................ 123
9.7.2 Fres-Q Calculation ........................................................................................................ 125
9.8 Averaging .................................................................................................................................... 127
9.9 Using probes ............................................................................................................................... 128
9.10 Unwrapped phase ....................................................................................................................... 131
9.11 Check for updates ....................................................................................................................... 133
10 Automation interface 134
11 Troubleshooting 135
Support 136
4 OMICRON Lab
Index
Index
Chart
.bode file ...................................................... 98
Context menu ......................................... 33
.bode3 file ................................................... 98
Chart ......................................................... 107
.bodex file ................................................... 98
Cleaning ...................................................... 11
COM ......................................................... 134
A Compensation ............................................ 75
B D
Block diagram ............................................. 21
Data / Memory ........................................... 121
B-SMC ........................................................ 64
Deletion of calibration .................................. 97
B-WIC ......................................................... 64
Delivered Items ........................................... 13
Disposal ...................................................... 12
C
Calibration ............................................. 75, 96 E
Full-Range .............................................. 75
Email (OMICRON Lab email address) ..... 136
User-Range ............................................ 75
Examples ..................................................... 23
Calibration .......................................
75, 84, 86, 88, 90, 92, 95, 96 Excel ......................................................... 100
OMICRON Lab 5
External Bridge ........................................... 74 Internal device calibration ........................... 75
External coupler .......................................... 53 Internal path compensation ........................ 75
External probes ......................................... 128
J
F Jump to Max .............................................. 115
Factory calibration ...................................... 75 Jump to Zero .............................................. 115
Features ...................................................... 98 Jump to Min ............................................... 115
Fres-Q ....................................................... 125
Full-Range ................................................... 75
Full-Range ...................................... 93, 95, 96
L
LabVIEW .................................................. 134
Function principle ........................................ 22
Level unit .................................................. 104
Loop Gain ................................................... 52
G
Gain Calibration .......................................... 76
Gain/Phase ................................................. 52
M
Matlab ....................................................... 134
Get from zoom .......................................... 109
Measurement configuration ........................ 26
Measurement modes ................................... 39
H External coupler .................................... 53
External Bridge ...................................... 74
Hardware setup .......................................... 37
Gain/Phase ............................................ 52
Hotline ...................................................... 136
Impedance Adapter ............................... 64
One-Port ................................................ 54
I Series-Thru ............................................
Shunt-Thru ............................................
72
69
Icons ........................................................... 30 Shunt-Thru with series resistance ......... 71
Impedance Adapter .............................. 64, 88 Transmission / Reflection ...................... 46
Voltage/Current ..................................... 73
Impedance Analysis
Impedance Adapter ................................ 64 Measurement trace .................................... 121
Shunt-Thru with series resistance ......... 71 Memory curves .......................................... 117
Impedance calibration ................................ 81 Memory traces .......................................... 117
Impedance Measurement
Result formats ................................. 40, 42
Impedance Analysis
N
One-Port ................................................ 54 NISM .......................................................... 123
Shunt-Thru ............................................. 69 Noise reduction .......................................... 127
6 OMICRON Lab
Index
R
Recycling .................................................... 12
Reflection .................................................... 84
OMICRON Lab 7
T Z
Technical Data ............................................. 15 Zooming .................................................... 109
Absolute maximum ratings .................... 15
Bode 100 specifications ........................ 16
Environmental Requirements ................ 18
Mechanical data .................................... 18
Power Requirements ............................. 17
System requirements ............................ 17
Temperature range ................................ 18
Technical support ...................................... 136
Thru calibration ..................................... 77, 79
Touchstone ............................................... 102
Trace configuration .............................. 28, 121
Trace math ................................................. 121
Transmission / Reflection ........................... 46
Troubleshooting ........................................ 135
U
Unwrap phase ........................................... 131
Update informer ......................................... 133
User-Range ................................................. 75
User-Range .......................................... 93, 95
V
Voltage/Current ..................................... 73, 92
W
Web (OMICRON Lab website) ................. 136
Welcome screen ......................................... 23
Window ....................................................... 24
8 OMICRON Lab
Contents
Index 5
OMICRON Lab 9
1 Safety instructions
Before operating Bode 100 and its accessories, read the following safety instructions carefully. If you
do not understand some safety instructions, contact OMICRON Lab before proceeding. When working
with Bode 100, observe all safety instructions in this document. You are responsible for every
application that makes use of an OMICRON or OMICRON Lab product. Any miss-operation can result
in damage to property or persons. Maintenance and repair of Bode 100 and its accessories is only
permitted by qualified experts either at OMICRON Lab or at certified repair centers.
Following these instructions will help you to prevent danger, repair costs and possible down time due
to incorrect operation. Furthermore, it ensures the reliability and life-cycle of Bode 100.
Use Bode 100 in observance of all existing safety requirements from national standards for
accident prevention and environmental protection.
Reading the Bode 100 manual alone does not release you from the duty of complying with all national
and international safety regulations relevant for working with Bode 100, for example, the regulation
EN50191 "Erection and Operation of Electrical Test Equipment”.
WARNING
Bode 100 is a SELV device (SELV = Safety Extra Low Voltage according to IEC
60950).
► Do not apply hazardous voltage levels >50 VDC or >25 VAC to the inputs of
Bode 100.
► Ensure that voltage and current probes used with Bode 100 are properly grounded
in accordance with their manufacturer's guidelines.
► When working with voltage or current probes, always connect the Bode 100's
ground terminal (available for HW Rev. 2 or higher) with a solid connection of at
least 3.6 mm² cross-section and not longer than 10 m to the ground terminal in the
laboratory.
► Be aware that no indication on Bode 100 shows that the output is active. This could
be especially critical if amplifiers are connected to Bode 100.
10 OMICRON Lab
Safety instructions
1.4 Disclaimer
The advisory procedures and information contained within this document have been compiled as a
guide to the safe and effective operation of Bode 100. It has been prepared in conjunction with
application engineers and the collective experience of the manufacturer.
The in-service conditions for the use of Bode 100 may vary between customers and end-users.
Consequently, this document is offered as a guide only. It shall be used in conjunction with the
customers own safety procedures, maintenance program, engineering judgment, and training
qualifications.
Using Bode 100 or its accessories in a manner not specified by the manufacturer may result in
damage to property or persons.
1.5 Cleaning
Use a cloth dampened with isopropanol alcohol to clean Bode 100 and its accessories.
OMICRON Lab 11
2 Compliance statements and recycling
12 OMICRON Lab
Bode 100 and accessories
Bode 100
multi functional test set Bode Analyzer Suite on DVD Wide-range AC power supply
including mains input plugs for
different national standards
BNC 50 Ω load (m) Bode 100 Quick Start Guide Multilingual safety instructions
The delivered items may vary a bit from the look shown above. Please refer to the packing
list received with the Bode 100 for further information
OMICRON Lab 13
3.2 Optional accessories
B-WIT 100 Wideband Injection Transformer
The B-WIT 100 is used to inject signals into control loops. Its main
application is in the stability analysis of switched mode power
supplies and linear voltage regulators.
B-AMP 12 amplifier
12 dB amplifier to boost the output signal of Bode 100 for
applications where more than 13 dBm are needed.
For more information on the above mentioned Bode 100 accessories and recommended
accessories manufactured by partner companies visit www.omicron-lab.com.
14 OMICRON Lab
Technical data
4 Technical data
In this section you can find the most important technical data for the Bode 100 Revision 2.
Technical data can change without notice.
You can download a detailed technical data sheet for Bode 100 from the OMICRON Lab website
www.omicron-lab.com → Bode 100 → Technical Data
OMICRON Lab 15
4.2 Bode 100 specifications
In this section you can find the most important technical data for the Bode 100. This
technical data is valid for Bode 100 R2 (Hardware revision 2). To find out what hardware
revision you use, please check 5.4 Hardware revisions on page 22.
Technical data can change without notice. You can download a detailed technical data sheet
from the OMICRON Lab website www.omicron-lab.com → Bode 100 → Technical Data
Characteristic Rating
OUTPUT
Voltage range -30 dBm...13 dBm
7 mVrms...1 Vrms at 50 Ω load
14 mVrms...2 Vrms at high impedance load
Frequency range 1 Hz...50 MHz
Wave form sinusoidal
Source impedance 50 Ω
Connector BNC
INPUT CH 1, INPUT CH 2
AC measurement range 100 mVrms full scale with 0 dB input attenuation
10 Vrms full scale with 40 dB input attenuation
Frequency range 1 Hz...50 MHz
Input impedance Selectable via software:
• 50 Ω
• 1 MΩ ±2% || 40...55 pF
Connectors BNC
Input attenuators Selectable via software:
0 dB, 10 dB, 20 dB, 30 dB, 40 dB
Receiver bandwidth Selectable via software:
1 Hz, 3 Hz, 10 Hz, 30 Hz, 100 Hz, 300 Hz, 1 kHz,
3 kHz , 5 kHz*
*only Bode 100 R2
Dynamic Range > 100 dB (10 Hz receiver bandwidth)
Gain Error < 0.1 dB (calibrated)
Phase Error < 0.5 ° (calibrated)
PC interface
Universal serial bus USB 2.0 or higher
Connector USB type B socket
16 OMICRON Lab
Technical data
Characteristic Rating
DC input
Supply voltage range +9 ... 24 V
Minimum DC supply power 10 W
Connector Coaxial power socket
Inner Diameter: 2.5 mm
Outer Diameter: 5.5 mm
Polarity
We strongly recommend you to use the power supply delivered with Bode 100.
OMICRON Lab 17
4.5 Environmental requirements
Table 4-5: Environmental requirements
Characteristic Rating
Dimensions (w x h x d) without connectors 26 cm x 5 cm x 26.5 cm / 10.25 " x 2 " x 10.5 "
Weight < 2 kg / 4.4 lbs
18 OMICRON Lab
Device overview
5 Device overview
Bode 100 is a USB controlled vector network analyzer. The system consists of the Bode 100 hardware
and the Bode Analyzer Suite software. In the following the Bode 100 hardware is described in detail.
To learn more about the Bode Analyzer Suite, please check out 6.1 Start screen on page 23 ff.
5.1 Connectors
CAUTION
To ensure save operation and to prevent injuries it is recommended to connect
Bode 100 to ground using the ground connector at the rear panel at all times.
NOTICE
To avoid damage of Bode 100 make sure that the absolute maximum ratings defined in chapter
4.1 Absolute maximum ratings on page 15 are not exceeded at any time.
For save operation it is strongly recommended only to use the power supply delivered with
Bode 100.
Bode 100 provides the following three connectors at the front panel:
• OUTPUT: signal output (BNC socket)
• CH 1: channel 1 signal input (BNC socket)
• CH 2: channel 2 signal input (BNC socket)
OMICRON Lab 19
Bode 100 provides the following three connectors at the rear panel:
• DC power input:
input for DC voltages from 10 V to 24 V (5.0 mm power supply plug with 2.5 mm pin)
• USB: data interface (USB type B port)
20 OMICRON Lab
Device overview
• Signal source:
The signal source of Bode 100 consists of an adjustable DDS sine-wave generator and adjustable
amplifiers. The output impedance of Bode 100 is 50 Ω.
Internal reference connections allow to directly connect the source signal to the receivers.
• Channel inputs:
Each of the Bode 100 input features adjustable attenuators for best signal / noise ratio and
software-switchable termination. Channel termination can be either 50 Ω or 1 MΩ. Without 50 Ω
terminations the inputs are AC coupled.
• Down conversion & sampling:
The input signal is down-converted to an intermediate frequency and sampled by a 24bit ADC.
The sampled data is sent to the PC and evaluated by the Bode Analyzer Suite.
More details on the hardware configuration can be found in 6.5 Hardware setup on page 37.
OMICRON Lab 21
5.3 Functional description
The flexible hardware concept of Bode 100 allows to use it for several applications such as:
• Transmission / Reflection measurements
• Gain / Phase (transfer function) measurements
• Impedance measurements
The device operates in a wide frequency range from 1 Hz to 50 MHz. Bode 100 creates a sine-wave
at a frequency and measures two voltages. The creation of the sine wave and both voltage
measurements are synchronized such that magnitude and phase relation of the two measured
voltages can be derived.
From the magnitude and phase ratio of the two voltages, the Bode Analyzer Suite calculates
Impedance, Reflection, Admittance, Transmission or complex Gain values of the DUT (Device Under
Test).
For a complete list of all possible measurements that you can perform with Bode 100
see 7 Measurement types and applications on page 39.
Your identification plate might look slightly different. The important information is visible in the
Option field. If Option is Rev. 2, you are using a Bode 100 R2. If Option is empty, you are
using a Bode 100 R1.
22 OMICRON Lab
Bode Analyzer Suite introduction
Step-by-step examples
Hint: Get a quick introduction to the Bode Analyzer Suite and how to use Bode 100 by following the
step-by-step examples. The following examples are available in this manual:
• Perform a Transmission / Reflection measurement on the IF filter DUT,
see Transmission / Reflection measurement example on page 47.
• Perform a one-port impedance measurement on the Quartz filter DUT,
see One-Port measurement example on page 56
• Measure impedance of an inductor using the impedance adapter,
see Impedance Adapter example on page 64
OMICRON Lab 23
The Start screen allows the following user interactions:
• Choose the device to use (1.). This field is only visible if you have a Bode 100 device connected to
your PC.
• Open a recent file or other file (2.). On your first start-up the demo-files are listed here. Check out
the examples that explain the content of the demo-files.
• Select one of the available measurement modes (3.) and start a measurement.
Hint: If you prefer to automatically start a measurement instead of entering the Start screen,
choose your default startup measurement mode by clicking on Set default startup and
choosing your preferred startup mode. You can also choose a .bode3 file to be your default
startup configuration.
24 OMICRON Lab
Bode Analyzer Suite introduction
OMICRON Lab 25
6.2.1 Measurement configuration
Frequency
In Frequency sweep mode you can change either Start
frequency and Stop frequency or Center and Span.
Get from zoom updates Start frequency and Stop
frequency with the current zoom window range.
Furthermore, the sweep mode can be Linear or
Logarithmic and the number of points in the sweep can
be chosen.
In Fixed Frequency mode only the Source frequency
can be adjusted. In this case the Bode 100 will display a
vector chart instead of a frequency dependent chart.
Source level
Choose between a constant or variable output level
(shaped level) and set the source level. The variable
output level feature is only available in Frequency
sweep mode. It allows to define different source levels
for different frequency points. To learn more about the
source control, refer to 9.2 Signal source settings on
page 104.
Attenuators
Set the input attenuators for Receiver 1 (Channel 1) and
Receiver 2 (Channel 2). If the measurement mode
supports two measurements (Transmission and
Reflection) you can set the attenuators for each
measurement. Possible attenuator values are 0 dB,
10 dB, 30 dB and 40 dB. Increase the attenuators when
you experience an overload, reduce the attenuators to
improve signal to noise ratio.
Receiver bandwidth
Set the maximum Receiver bandwidth used for the
measurement. Receiver bandwidth will be reduced
internally if the measurement frequency is smaller than
the Receiver bandwidth setting.
Select a high Receiver bandwidth to increase
measurement speed.
Reduce Receiver bandwidth to reduce noise and to
catch narrow-band resonances.
26 OMICRON Lab
Bode Analyzer Suite introduction
Nominal impedance
The nominal impedance or characteristic impedance
value is used to calculate the Reflection factor. See also
7.2 Impedance measurement introduction on page 42.
Note that this field is only visible if a reflection
measurement is performed.
Measurement mode
Shows what measurement mode is currently used. All
available measurement modes are explained in
7 Measurement types and applications on page 39.
OMICRON Lab 27
6.2.2 Trace configuration
In a Frequency Sweep measurement, the right hand side of the Bode Analyzer Suite shows the Trace
configuration. The Trace configuration allows to choose what measurement (Gain, Impedance,
Reflection, Admittance) is performed and how it is displayed in the chart.
Trace configuration box: The Trace configuration box displays the trace-name
and contains the following trace-display settings:
Measurement: Impedance, defines that Trace 1
measures impedance.
Display: Measurement, indicates that the chart shows
the measured trace.
Note that memory curves are displayed as well.
Format: Magnitude, defines that Trace 1 displays the
Magnitude of Impedance.
Ymax: 100 Ω, The upper limit of the y-axis displayed in
the diagram.
Ymin: 1 mΩ, The lower limit of the y-axis displayed in
the diagram.
Y-axis scale : Log(Y), Currently the y-axis is set to a
logarithmic scaling.
Learn more about the trace configuration box in
9.6 Using the trace configuration on page 121.
Memory configuration box: The memory configuration box allows to control the
memory curves:
Hint: By clicking the inner border of the Measurement configuration or Trace configuration
you can collapse these configuration areas to create a bigger chart area. You can fold out
the configurations anytime by clicking the respective areas at the side of the chart area. For
more details refer to the figure below.
28 OMICRON Lab
Bode Analyzer Suite introduction
OMICRON Lab 29
6.2.3 Ribbon controls
The Bode Analyzer Suite ribbons feature the following commands:
Home ribbon
Memory ribbon
30 OMICRON Lab
Bode Analyzer Suite introduction
Hide all available memory traces. They will not be shown in the
diagram.
You can find more information about the use of the memory traces in 9.5 Using the memory traces on
page 117.
View ribbon
Cursor ribbon
OMICRON Lab 31
6.2.4 Status bar
The Status bar has several displays and interactive control elements. These are:
Source indicator
The source indicator shows if the signal source of Bode 100 is
switched on. By moving the mouse over the indicator, a pop-up
allows to change between Auto off and Always on setting. More
details regarding the source setting can be found in 9.2 Signal
source settings on page 104.
Overload indicators
The overload indicators show the signal level at the receivers of
Bode 100. Red color indicates an overload of the receiver. An
overload warning will be shown in the chart in such a case.
Internal device calibration indicator
Shows the date of the last performed internal device calibration.
Move the mouse over the indicator in order to perform a new
internal device calibration.
Device connection indicator
Displays the serial number of the connected device. If no device is
connected, "No device" is shown. Move the mouse over the
indicator in order to search or re-connect to a Bode 100 device.
32 OMICRON Lab
Bode Analyzer Suite introduction
OMICRON Lab 33
6.4 Options menu
The Options menu allows you to modify several functions of the Bode Analyzer Suite. You can access
the Options menu by either clicking the icon in the top right corner of the Bode Analyzer Suite's
main window or by clicking File → Options.
General:
Default level unit: allows you to change the unit for Bode 100's
source level setting. You can choose dBm, Vpp or Vrms.
34 OMICRON Lab
Bode Analyzer Suite introduction
Logging:
Log Level:This function allows you to define the severity level of
the events stored in the log-file. Default is Warning.
UDP Logging: allows you to enable event logging via UDP and to
define the used UDP port.
Logging to a file: allows you to enable the logging of events to a
log file and to define the location of the log file on your computer's
hard drive.
Common:
Allows you to enable the device selection in the start up screen and
to change your preference in relation to the Customer Experience
Improvement Program.
Chart:
In this section you can optimize the size of the text fonts and the
thickness of the measurement traces in the exported chart .
Further on, you can enable the inclusion of the chart legend and
the cursor grid. In addition the position of the cursor grid in the
exported chart and the image file format can be defined.
Data:
In this section you can choose the decimal separator and the field
separator for the clipboard export.
Find more information in 9.1.2 Use the copy to clipboard functions
to export data on page 98.
In this section you can define several parameters for the CSV-
Export, Excel-Export and Touchstone-Export of the measured
data. These parameters are the default values that will be used for
all future exports you perform.
Find out more in 9.1.3 Exporting measurement data to CSV or
Excel files on page 100.
Here you can choose if comments, the cursor table, the chart
legend or shaped level are included in the report or not.
Additionally, you can choose if you want to use a custom report or
the standard report. Finally you can select if the report should be
opened after its generation and the program that should be used to
display the report.
Detailed information is available in 9.1.5 Generate a PDF report on
page 103.
OMICRON Lab 35
In the Chart section of the Options Menu you can change the following settings:
The sections in this unit allow you to optimize the quality and
appearance of the charts displayed in the Bode Analyzer Suite.
Further on, you can select if the axis labels are displayed in
scientific or engineering format.
General:
Here you can select the maximum number of memory traces,
the default memory line pattern (e.g. solid or dashed) as well as
if the deletion of a memory trace needs to be confirmed or not.
Alternating memory trace color mode:
By enabling this mode you can make it easier to find out to which
trace a memory belongs. If activated each memory alternates the
memory color and the color of the trace it belongs to as shown
below:
Hint: Click to switch back to the default settings of all options at any
time.
36 OMICRON Lab
Bode Analyzer Suite introduction
By clicking on the Hardware setup icon , the hardware setup dialog is opened.
The hardware setup dialog shows the internal connections of Bode 100 as well as the external
connection to the DUT. Depending on the selected measurement mode, hardware settings such as
Channel termination, Receiver connection or an external Probe factor can be changed by clicking on
the icons shown in the Hardware setup dialog.
Depending on the measurement mode, some of the following settings can be changed by the user:
• Source mode: Choose between Auto off or Always on. More details on the source behavior of
Bode 100 can be found in 9.2 Signal source settings on page 104.
• Source level: Set the constant source level or the reference level when the shaped level function
is used.
• Receiver bandwidth: Select the receiver bandwidth used for the measurement.
OMICRON Lab 37
• DUT settling time: Time between applying the measurement signal and starting to measure at the
receiver. A DUT settling time is needed if the DUT introduces a significant time delay before the
output reaches its final reaction to the input stimulus.
• Attenuator 1 and Attenuator 2: Select the input attenuators.
• Reference switch: Receiver 1 and Receiver 2 can be connected either internally or externally
depending on the measurement mode.
• Termination switch: When switched on, the Channel 1 and Channel 2 inputs are terminated with
50 Ω. If the switch is open, the input impedance is 1 MΩ.
• Probe 1 and Probe 2: Some measurement modes allow you to manually enter a probe factor. For
more details on using probes see 9.9 Using probes on page 128.
38 OMICRON Lab
Measurement types and applications
Impedance Analysis
The Impedance Analysis Tab contains the following measurement types:
1. One-Port
2. Impedance Adapter
3. Shunt-Thru
4. Shunt-Thru with series resistance
5. Series-Thru
6. Voltage / Current
7. External Bridge
In the following chapters all measurement types are explained in detail.
OMICRON Lab 39
7.1 Gain measurement introduction
Bode 100 offers two different ways of measuring Gain. Either with the internal reference or the
external reference. Internal reference means that Receiver 1 is internally connected to the Bode 100
signal source picking up the source voltage. External reference means that Receiver 1 is routed to the
front panel input Channel 1.
Depending on the Receiver 1 connection, Gain is measured as shown in the following table:
Where V0 is the internal source voltage. If Gain therefore equals the transfer function of a 2-
Channel 2 is terminated with 50 Ω (default), Gain port DUT if Channel 1 is connected to the DUT
equals the scattering parameter S21 of a two-port input port and Channel 2 is connected to the DUT
DUT (Port 1 is connected to Bode 100 output and output port.
port 2 is connected to Bode 100 Channel 2).
The following two measurement modes can be used to perform a Gain measurement:
1. Transmission / Reflection: This mode allows both, measurements with internal and external
reference connection.
2. Gain / Phase: Is used to measure Gain from Channel 1 to Channel 2 (Frequency Response
Measurement).
Since the gain result is a complex number you can choose how gain shall be displayed. You can
select the result formats by clicking the drop down Format in the trace configuration box.
40 OMICRON Lab
Measurement types and applications
OMICRON Lab 41
7.2 Impedance measurement introduction
Bode 100 offers several ways of measuring Impedance, Reflection or Admittance. Impedance,
Reflection and Admittance are directly related to each other by the following equations:
Z0 can be changed by the user in the measurement configuration. The nominal impedance
Z0 field is only visible if a measurement trace is set to Reflection.
The Impedance Analysis modes allow you to display the measurement results in various formats. You
can select the result formats by clicking the drop down Format in the trace configuration box.
Depending on the chosen measurement the following result formats are available:
42 OMICRON Lab
Measurement types and applications
OMICRON Lab 43
Reflection Coefficient Result Formats
44 OMICRON Lab
Measurement types and applications
where R is the real part of the impedance (resistance) and X the imaginary part of the
impedance (reactance).
ω is the angular frequency with the frequency f.
tan(d) of impedance
Admittance Y:
where G is the real part of the admittance (conductance) and B the imaginary part of
the admittance (susceptance).
ω is the angular frequency with the frequency f.
tan(d) of admittance
OMICRON Lab 45
Reflection Coefficient Γ:
Tg as well as Q(Tg) are calculated in the same way as for the gain measurement (see 7.1 Gain
measurement introduction on page 40).
Therefore some hardware settings are available twice. Once for the Gain measurement and once for
the Impedance measurement.
Also the hardware setup dialog is available twice. Once for the Gain measurement and once for the
impedance measurement.
For details on how the Gain is calculated, please check 7.1 Gain measurement introduction on
page 40.
46 OMICRON Lab
Measurement types and applications
Typical applications
Typical applications for the Transmission / Reflection measurement mode are:
• Measuring Transmission and Reflection of filters such as IF filters or EMI filters.
• Comparing results from measurements with internal and external reference connection
(the Transmission / Reflection measurement mode is the only measurement mode that allows
changing the Receiver 1 connection).
• Measuring Gain of RF amplifiers in the 50 Ω domain.
OMICRON Lab 47
Now start the Bode Analyzer Suite and enter the Transmission / Reflection measurement mode by
clicking on .
Before starting the measurement set the Start and Stop frequency to the values shown below:
After setting the Start and Stop frequency the Center frequency as well as the frequency
Span are set automatically. Alternatively you can enter the Span and Center and the Start
and Stop frequency are updated accordingly
Now you are ready to start your first measurement. Simply click in the home ribbon. As a result you
will see a first measurement comparable to the one shown in the figure below.
48 OMICRON Lab
Measurement types and applications
Trace 1 (red curve) shows the Magnitude of the Gain (= Magnitude of S21) while Trace 2 (blue curve)
shows the Magnitude of Reflection (= Magnitude of S11). You can change Format for both traces to
display other results such as Phase or Real and Imaginary components
To optimize the chart you can right click onto the chart and select Optimize as shown below. For more
information on the chart's context menu check out 6.3 Chart context menu on page 33.
OMICRON Lab 49
Figure 7-3: Context menu of chart
50 OMICRON Lab
Measurement types and applications
Further on you can use the cursors to perform measurements. To do so simply drag the cursors to the
point you want to measure (1.) and check out the results in the cursor grid (2.) as shown in 7-4 on
page 51. For more cursor functions visit 9.4 Working with cursors and the cursor grid on page 115.
Congratulations you have performed your first measurement with the Bode 100. You can load the
settings for the measurement by clicking File → Open → and then navigating to: "%APPDATA%
\OMICRON Lab\Bode Analyzer Suite\Demo Files\". The file you will need is: TransRefl_IF-
Filter.bode3
Hint: The Transmission / Reflection is the most flexible measurement setup for the
Bode 100. By selecting this setup you can switch between internal and external reference.
Further on, you can switch the input impedance of input CH1 and input CH2 between 50 Ω
and high impedance.
OMICRON Lab 51
7.3.2 Gain / Phase
The Gain / Phase measurement mode is designed to measure the transfer function of a DUT using the
external reference connection. This means that both Channel 1 and Channel 2 are active.
Gain therefore equals the transfer function of a 2-port DUT if Channel 1 is connected to the DUT input
port and Channel 2 is connected to the DUT output port. The inputs Channel 1 and Channel 2 are set
to 1 MΩ by default.
Details on the gain measurement can be found in 7.1 Gain measurement introduction on page 40.
Calibration
The Gain / Phase measurement mode does not require calibration to perform a measurement.
However, to remove the influence of probes and cables Gain (Thru) calibration is recommended. For
more details regarding the Gain calibration please refer to 8 Calibration on page 75.
Typical applications
Typical applications for the Gain / Phase measurement mode are:
• Measuring the transfer function of filters or other circuits.
• Measuring in-circuit transfer functions using high-impedance probes.
• Measuring the transfer function of amplifiers etc.
• Measuring loop stability of power supplies.
52 OMICRON Lab
Measurement types and applications
Measurement example
For detailed measurement examples using the Gain / Phase measurement mode, please check out
the application notes at www.omicron-lab.com/BodeManualAppNotes. The following application notes
use the Gain / Phase measurement mode:
• DC/DC Converter Stability Measurements
• Bipolar Transistor AC Current Gain Measurement
• Op-Amp measurements
• PSRR Measurement
• And many more...
Calibration
Please note that the external coupler measurement mode requires an impedance calibration (Open,
Short, Load). For more details on how to perform an impedance calibration see 8.3.2 Calibrating an
External Coupler or External Bridge measurement on page 86.
Typical applications
Typical applications for the external coupler measurement mode are:
• Measuring medium-wave antennas.
• Measuring impedance with high-power amplifiers.
Measurement example
For a detailed measurement example using the external coupler measurement mode, please check
out the medium wave antenna measurement application note at
www.omicron-lab.com/BodeManualAppNotes.
OMICRON Lab 53
7.4 Impedance analysis
7.4.1 One-Port
The One-Port measurement mode is designed to perform quick impedance, admittance and reflection
measurements. One advantage of the One-Port impedance measurement mode is that no external
calibration is required. Bode 100 can measure impedance directly at the output port.
Measurement information
Bode 100 derives the impedance by evaluating the internal source voltage and the output voltage.
Receiver 1 as well as Receiver 2 are internally connected. General details on impedance
measurements with Bode 100 can be found in 7.2 Impedance measurement introduction on page 42.
54 OMICRON Lab
Measurement types and applications
Since the output impedance of Bode 100 is 50 Ω, the one-port measurement provides highest
sensitivity for a DUT having an impedance close to 50 Ω. The method is generally suitable to measure
impedance values between roughly 500 mΩ and 10 kΩ.
For measurements close to the limits of this method it is highly recommended to perform a careful
User-Range calibration to achieve best results.
Calibration
The One-Port impedance measurement mode does not require calibration to perform a measurement.
However, to achieve highest accuracy a calibration is recommended. Furthermore a calibration allows
to move the reference plane from the output port of Bode 100 to the end of a connection cable. This
compensates the effect of the connection cable.
For more details on how to perform an Impedance calibration please refer to 8.3.1 Calibrating a
Reflection or One-Port Impedance measurement on page 84.
Typical applications
Typical applications for the One-Port impedance measurement mode are:
• Measuring impedance of passive components.
• Measuring impedance of cables, piezo-elements or any one-port DUT.
OMICRON Lab 55
One-Port measurement example
In this measurement example we will determine the series ans parallel resonance frequency of a 12
MHz quartz filter. Further on, we will display the quartz filter's reflection curve in a Smith chart.
Connect the input IN 2 of the test object "Quartz Filter" to the OUTPUT of Bode 100 using a BNC
cable. Further on, connect the BNC short delivered with Bode 100 to the corresponding output OUT 2.
The complete setup is shown in the figure below.
Figure 7-6: Connecting the test object Quartz Filter to Bode 100
Now start the Bode Analyzer Suite and enter the One-Port measurement mode by clicking Impedance
56 OMICRON Lab
Measurement types and applications
Before starting the measurement set the Center frequency, frequency Span and the Number of
points to the values shown below.
Further on, select sweep linear:
Now click in the home ribbon. As a result you will see a first measurement comparable to the one
shown in the figure below.
OMICRON Lab 57
Figure 7-7: Impedance measurement of the test object Quartz Filter
Trace 1 (red curve) shows the Magnitude of the Quartz Filter's impedance while Trace 2 (blue curve)
shows the Phase of the Quartz Filter's impedance.
Before continuing the measurement please switch of Trace 2 by unchecking the corresponding check
box .
To determine the parallel and series resonance of the Quartz filter we need to zoom in. You can do this
by clicking into the chart on the top left corner of the intended zoom area, keep the mouse button
pressed and pull it to the lower right corner of the intended zoom area as shown.
58 OMICRON Lab
Measurement types and applications
In the zoomed window you will see that you are not having enough frequency points. By pressing
you can set the start and stop frequency of the measurement to
match the zoomed window. Right Click into the chart and select Optimize. Repeat these steps until
you achieve a chart as shown in 7-8 on page 59
Figure 7-8: Optimizing the frequency resolution with Get from zoom
For more information on the zoom functions and optimizing check out 9.3.2 Zooming the
measurement curve on page 109 and 6.3 Chart context menu on page 33.
OMICRON Lab 59
After you have optimized the chart you can measure the series resonance and parallel resonance
using the cursors. To do so right-click into the chart area close to the red curve and choose Cursor 1
and then Jump to Min (Trace 1). Then right-click into the chart area once more and choose Cursor 2
and then Jump to Max (Trace 1)
For more information on cursor functions visit 9.4 Working with cursors and the cursor grid on
page 115.
60 OMICRON Lab
Measurement types and applications
Figure 7-10: Series and parallel resonance frequency of the quartz filter
To determine the series and parallel resonance frequencies check out the cursor grid as shown in
7-8 on page 59:
• Series resonance frequency (Cursor 1 - green): 11.996768 MHz
• Parallel resonance frequency (Cursor 2 - orange): 11.998572 MHz
• Offset between the series and parallel resonance frequency (Delta C2-C1): 1.8 kHz
Your measurement results can be slightly different since each quartz filter behaves a little bit
different.
One characteristic of resonance frequencies is that the inductances and capacitances compensate
each other. This means that at the series and parallel resonance the impedance of our quartz filter
should be purely resistive. An elegant way to check this is to display the quartz filters reflection curve
as a Smith chart.
OMICRON Lab 61
Smith charts were developed at a time when it was still difficult to directly measure the frequency
swept impedance of measurement objects. The Smith chart is used to determine the impedance at a
certain point of the reflection curve. To display the Smith chart of our quartz filter's impedance apply
the settings shown below to Trace 1:
After applying the settings a smith chart like the one shown below will be displayed:
62 OMICRON Lab
Measurement types and applications
As you can see both cursors are very close to the horizontal (=resistive) axis of the Smith chart.
However, you can also see that the imaginary part for both measurements is not exactly 0 Ω. The
reason for this is the chosen number of frequency points and the frequency resolution resulting from it.
Fell free to use more points and zooming to determine the exact frequencies at which the imaginary
part of the impedance becomes 0 Ω
Congratulations you have performed your impedance measurement with the Bode 100. You can
load the settings for the measurement by clicking File → Open → and then navigating to:
"%APPDATA%\OMICRON Lab\Bode Analyzer Suite\Demo Files\".
The file you will need is: OnePort_Quartz-Filter.bode3.
OMICRON Lab 63
7.4.2 Impedance Adapter
The impedance adapter measurement mode is especially designed for measurements with the
OMICRON Lab impedance test fixtures B-WIC and B-SMC. The impedance adapter measurement
mode ensures that Bode 100 is configured correctly to achieve best results when measuring with both
B-WIC and B-SMC.
Calibration
The impedance adapter measurement mode requires impedance (open, short, load) calibration.
For more details on how to calibrate the B-WIC or B-SMC impedance adapter, please refer to
8.3.3 Calibrating an Impedance Adapter measurement on page 88.
Measurement information
With B-WIC and B-SMC, the dynamic range of both input channels is used. This widens the usable
impedance measurement range to 20 mΩ to 600 kΩ.
It is recommended to use the 0.5 m BNC cables delivered with Bode 100 to connect B-WIC or B-SMC
to the Bode 100.
B-WIC and B-SMC are designed to measure physically small DUTs. Stray-fields between the DUT and
the grounded housing of the impedance adapters might introduce a systematic measurement error.
The error is negligible when measuring physically small objects. To measure physically big DUTs it is
recommended to use a grounded measurement configuration such as shown in 7.2.1 One-Port on
page 54.
Typical applications
Typical applications for the impedance adapter measurement mode are:
• Measuring impedance of capacitors, inductors and other passives (THT and SMC).
• Measuring impedance piezo-elements or quartz elements.
64 OMICRON Lab
Measurement types and applications
Before you can start a measurement you have to perform a Full range calibration. To do so please
follow the steps described in Impedance Adapter Calibration on page 88.
After having performed the calibration please put the inductor you want to measure into the
impedance measurement adapter as shown in 7-12 on page 65.
Since it is not known in what frequence range the examined inductor is working please change the
stop frequency to 50 MHz.
OMICRON Lab 65
Now click in the home ribbon. As a result you will see a first measurement comparable to the one
shown in the figure below. For sure your result will look different since you are using a different
inductor.
66 OMICRON Lab
Measurement types and applications
Trace 1 (red curve) shows the Magnitude of the inductor's impedance while Trace 2 (blue curve)
shows the phase of the inductor's impedance. The magnitude curve is rising with 20 dB per decade,
this indicates that we are really measuring an inductor. To measure the resistance Rs and inductance
Ls of the inductor simply change the format for Trace 1 and Trace 2 as shown.
To get a better view on the Ls and Rs it is recommended to switch to two diagrams. To do so follow
the instructions described in 9.3.1 Configure the diagrams on page 107.
OMICRON Lab 67
Well, and now we have our result:
Figure 7-14: Measurement of a 15µH inductor with the B-WIC impedance adapter
By using the cursors we can gather the following information on the measured inductor:
• The inductor has an inductance of 15 µH up to 220 kHz
• The resistance of the inductor starts around 20 mΩ and rises up to 2 Ω at 220 kHz
• Above 220 kHz the inductance starts to drop and slightly above 50 MHz the inductor will have its
resonance frequency and become capacitive.
68 OMICRON Lab
Measurement types and applications
Congratulations you have successfully used the B-WIC impedance measurement adapter with the
Bode 100. You can load the settings for the measurement by clicking File → Open → and then
navigating to: "%APPDATA%\OMICRON Lab\Bode Analyzer Suite\Demo Files\".
The file you will need is: ImpAdapt_Inductor.bode3.
Attention: Since your setup will be different the file should only be used to explore the different
measurement formats offered by Bode 100. Before you execute an own measurement you will have
toperform a new calibration.
For a detailed measurement example using the impedance adapter measurement mode to
measure capacitors, please check out the ESR measurement application note at
www.omicron-lab.com/BodeManualAppNotes
7.4.3 Shunt-Thru
The Shunt-Thru measurement mode is especially suitable to measure very small impedance values. It
is basically an S21 transmission measurement in a special configuration. The impedance is calculated
from the measured S21 parameter.
Measurement information
Bode 100 measures S21 gain and calculates impedance Z using the equation:
The Shunt-Thru measurement configuration emulates a 4-wire kelvin connection. The output drives a
current thru the device under test that is shunted between the output signal and GND. Channel 2
measures the voltage drop that occurs at the DUT. This measurement mode offers highest sensitivity
for low-impedance value DUT. The recommended impedance measurement range starts at roughly
1 mΩ. With amplifiers or pre-amplifiers also µΩ measurements can be performed.
Shunt-Thru measurement configuration offers low sensitivity for high impedance DUTs. It is not
recommended to measure impedance values much higher than 100 Ω.
The Shunt-Thru configuration inherently suffers a ground-loop error at low frequencies. The
current flowing thru the cable shield of the connection to Channel 2 ground introduces a
measurement error that can become significant at frequencies below 10 kHz to 100 kHz
when measuring very low impedance values. To suppress respectively reduce the ground-
OMICRON Lab 69
loop error at low frequencies, use a common-mode choke or common-mode transformer or
an active isolation device. Note that the Shunt-Thru transformation from S21 to impedance
assumes 50 Ω as source impedance and input impedance.
To improve signal to noise ratio for very low impedance measurements, you can use a 50 Ω
amplifier at the Output of Bode 100 as shown in the image below. Use calibration to remove
the amplifier gain and phase shift.
Calibration
The Shunt-Thru measurement is basically a Gain measurement that is transformed to an impedance.
Therefore two calibrations are possible. Either a Thru-calibration or an Open, Short, Load calibration.
Thru calibration calibrates the underlying S21 measurement and removes the gain/phase shift of the
cable connection, common mode choke or amplifier.
Open, Short, Load calibration shifts the reference plane directly to the calibration plane.
For more details on calibrating a Shunt-Thru measurement, please refer to 8.3.4 Calibrating a Shunt-
Thru or Series-Thru measurement on page 90.
Typical applications
A typical application for the Shunt-Thru measurement mode is the ESR measurement of ultra-low ESR
decoupling caps.
70 OMICRON Lab
Measurement types and applications
Measurement information
Bode 100 measures S21 gain and calculates impedance Z using the equation:
Compared to the normal Shunt-Thru measurement mode, the series resistors increase the maximum
measurable impedance. This is of advantage when one needs to measure from roughly 10 mΩ to
some kΩs.
The higher the series Resistors Rs are chosen, the higher the maximum recommended impedance is.
However, at the same time the lower impedance limit rises.
OMICRON Lab 71
The following table shows some Rs values and their influence on the impedance measurement range:
The Shunt-Thru with series resistor configuration suffers from the same systematic error as
the normal Shunt-Thru configuration. Please refer to 7.2.3 Shunt-Thru on page 69 for more
details about the cable-braid-error.
Calibration
The Shunt-Thru with series resistor measurement requires at least one Thru calibration.
Thru calibration must be performed with the series resistors included.
For more details on calibrating a Shunt-Thru measurement, please refer to 8.3.4 Calibrating a Shunt-
Thru or Series-Thru measurement on page 90.
7.4.5 Series-Thru
The Series-Thru measurement configuration is especially suitable to measure very high impedance
values. It is basically an S21 transmission measurement in a special configuration. The impedance is
calculated from the measured S21 parameter.
Measurement information
Bode 100 measures S21 gain and calculates impedance Z using the equation:
The Series-Thru configuration offers high sensitivity for high-impedance DUTs. Impedance values in
the MΩ region can be measured. Using an output amplifier further increases the upper impedance
measurement limit.
Shunt-Thru measurement configuration is not suitable for low-impedance DUTs. It is not
recommended to measure impedance values below roughly 1 kΩ.
One advantage of the series-thru connection is that a shielded test-setup can easily be constructed.
72 OMICRON Lab
Measurement types and applications
Calibration
The Series-Thru measurement is basically a Gain measurement that is transformed to an impedance.
Therefore two calibrations are possible. Either a Thru-calibration or an Open, Short, Load calibration.
Thru calibration calibrates the underlying S21 measurement and removes the effect of the cable
connection to the DUT.
Open, Short, Load calibration shifts the reference plane directly to the calibration plane.
For more details on calibrating a Series-Thru measurement, please refer to 8.3.4 Calibrating a Shunt-
Thru or Series-Thru measurement on page 90.
Typical applications
A typical application for the Series-Thru measurement is the measurement of DUTs with low
conductivity (high impedance).
7.4.6 Voltage/Current
The Voltage/Current measurement mode is basically a Gain measurement with external reference
similar to the Gain/Phase measurement mode. However, the fact that the Gain is treated as an
impedance result offers all impedance result formats such as L, C and Q calculations.
Measurement information
Bode 100 measures Gain and transforms it directly to impedance Z using:
The voltage/current measurement is very flexible. The usable impedance measurement range cannot
be generalized since it strongly depends on the used probes and connections. Using highly sensitive
current sensing, very high impedance values can be measured. Using very sensitive voltage
measurements, very low impedance values can be measured.
Calibration
The Voltage/Current measurement is basically a Gain measurement that is transformed to an
impedance. Therefore two calibrations are possible. Either a Thru-calibration or an Open, Short, Load
calibration.
Thru calibration calibrates the underlying gain measurement and removes gain and phase shifts of the
probes. A 1 Ω resistor is needed to perform a Thru calibration in the Voltage/Current measurement
mode.
Open, Short, Load calibration shifts the reference plane directly to the calibration plane.
OMICRON Lab 73
For more details on calibrating a Voltage/Current measurement, please refer to 8.3.5 Calibrating a
Voltage/Current measurement on page 92.
Typical applications
The Voltage/Current measurement is suitable for a high variety of measurement applications. It is the
mode of choice for every impedance measurement that measures voltage and current separately.
Typical measurements are:
• Input impedance measurement of active circuits such as power supplies.
• Output impedance measurement of active circuits such as power supplies.
Measurement example
For detailed measurement examples using the voltage/current measurement mode, please check out
the Non-Invasive stability application note at www.omicron-lab.com/BodeManualAppNotes.
Calibration
The external bridge measurement mode requires impedance (open, short, load) calibration.
For more details on how to calibrate the an external bridge, please refer to 8.3.2 Calibrating an
External Coupler or External Bridge measurement on page 86.
Measurement information
The external bridge measurement mode is similar to the Impedance Adapter measurement mode but
allows you to change the channel termination and input attenuators to adjust them according to your
needs.
Measurement example
For a detailed measurement example using the external bridge measurement mode, please check out
the High-impedance measurement application note at www.omicron-lab.com/BodeManualAppNotes.
74 OMICRON Lab
Calibration
8 Calibration
This section explains how to compensate unwanted effects of the measurement setup and how to
improve the accuracy of your measurement results. Bode 100 offers the following possibilities to
calibrate a test setup or the device itself:
External calibration
External calibration can be used to compensate e.g. the frequency response of probes, cables or the
test setup. Depending on the used measurement mode Bode 100 offers Gain calibration as well as
Impedance calibration.
Hint: To achieve maximum accuracy, do not change the attenuators after having performed
an external calibration.
Press the button Click here to perform a new internal device calibration and the device will start a
new internal calibration. The calibration takes roughly 1 min. During the calibration you cannot perform
any measurements with Bode 100.
OMICRON Lab 75
8.2 Performing a Gain Calibration
Gain calibration (also called Thru calibration) is used to remove the gain and phase error introduced
by the connections between the measurement instrument and the DUT in a gain or transmission
measurement.
To achieve maximum accuracy, do not change the attenuators after having performed an
external calibration.
Hint: Thru calibration can also be used in impedance measurements that are based on a
gain measurement. These measurement modes are e.g. Shunt-Thru, Series-Thru or Voltage/
Current. When performing a Thru calibration in such a mode, the underlying gain
measurement is calibrated and afterwards the calibrated gain result is transformed to
impedance.
3. The calibration dialog opens and the calibration state shows Not Performed.
4. Ensure that the calibration setup is connected properly and press Start.
5. Wait until the calibration has completed and the calibration state shows Performed.
76 OMICRON Lab
Calibration
The Transmission / Reflection mode offers the possibility to measure Transmission and
Reflection sequentially.
Note: The gain or Thru calibration is only applied to the gain measurement. If you want to
calibrate the Impedance, Reflection or Admittance measurement, refer to 8.3.1 Calibrating a
Reflection or One-Port measurement (see page 84).
In the Transmission / Reflection measurement mode Channel 1 is not in use by default. Receiver 1 is
connected internally to the signal source through the internal reference. The Channel 2 termination is
set to 50 Ω, therefore by default the Gain result equals the transmission S-parameter S21 from the
OUTPUT port to the CH2 port. If you choose to measure with the External reference connection,
please refer to 8.2.2 Calibrating a Gain/Phase measurement on page 79.
OMICRON Lab 77
The following picture shows a typical transmission calibration setup. The DUT is replaced by a Thru-
connector.
The factory calibration of Bode 100 moves the reference plane exactly between two cables
of 0.5 m length. So you can measure S21 using the delivered cables having a well calibrated
test-setup.
78 OMICRON Lab
Calibration
Figure 8-2: Thru calibration setup for gain/phase measurement with BNC cables.
The following picture shows a typical gain calibration setup using external voltage probes. Both probes
must be connected to the same signal during Thru calibration.
OMICRON Lab 79
Figure 8-3: Thru calibration setup for gain/phase measurement using scope probes.
Hint: If you use external scope probes, you can also adjust the probes manually using the
compensation screw at the probe tip. To do so, perform a continuous gain/phase sweep over
the frequency range of interest and adjust the probe compensation until you receive a flat
0 dB and 0 ° line. Mark the probes with Channel 1 and Channel 2 such that you can re-use
the similarly adjusted probes.
Hint: When measuring a transfer function directly in a circuit you can always check your
calibration by connecting both probes to the same point in the circuit. The result must show
0 dB and 0 °. Please note that this measurement might be influenced by additional noise
from the circuit.
80 OMICRON Lab
Calibration
To achieve maximum accuracy, do not change the attenuators after having performed an
external calibration.
3. In the calibration dialog, the calibration state shows Not Performed for all three calibration points.
Wait until the Open calibration has completed and the calibration state shows Performed.
OMICRON Lab 81
6. Close the calibration dialog after Open, Short and Load have been performed.
This means that the calibration is active now. You can connect your DUT and perform a calibrated
measurement.
82 OMICRON Lab
Calibration
In the Advanced Settings region you can change the following values:
1. The Load Resistor value represents the value of the resistor used for Load calibration.
2. Short Delay Time is the time delay of the Short element used for Short calibration.
• The default settings for Load Resistor and Short Delay Time depend on the
measurement mode.
• If you change a value from its default a warning sign will be shown
• Changing Load Resistor or Short Delay Time will delete the corresponding calibration!
OMICRON Lab 83
8.3.1 Calibrating a Reflection or One-Port Impedance measurement
In this section you learn how to calibrate an Impedance, Reflection or Admittance measurement in the
Transmission / Reflection measurement mode or in the One-Port impedance measurement
mode.
The Transmission / Reflection mode offers the possibility to measure Transmission and Reflection
sequentially. Please note that the Impedance (Open/Short/Load) calibration is only applied to a
Impedance, Reflection or Admittance measurement. If you want to calibrate a Gain measurement
please refer to 8.2.1 Calibrating a Transmission (S21) measurement (see page 77).
In the Transmission / Reflection measurement mode or in the One-Port impedance measurement
mode both receivers are internally connected to the 50 Ω source resistance. Bode 100 is internally
calibrated such that it measures the Impedance/Reflection directly at the OUTPUT port of the device.
The reference plane is directly at the OUTPUT port (BNC connector).
When connecting a DUT with a coaxial cable, the cable introduces additional impedance and time-
delay. To compensate these effects, the reference plane can be moved to the end of the cable by
performing an Open/Short/Load calibration at the end of the cable.
Figure 8-4: Shifting the reference plane by performing Open, Short and Load Calibration
84 OMICRON Lab
Calibration
Hint: The load delivered with the Bode 100 is marked with its exact impedance. You can
improve the calibration accuracy by entering this value in the Advanced Settings area.
The Short Delay Time in the Advanced Settings area has been chosen to match the Short
elements delivered with Bode 100. If your short is marked with Rosenberger you can set the
Short Delay Time to 40 ps, if it is marked with Radiall to 60 ps.
OMICRON Lab 85
8.3.2 Calibrating an External Coupler or External Bridge
measurement
In this section you learn how to calibrate an Impedance, Reflection or Admittance measurement in the
External Coupler measurement mode or in the External Bridge impedance measurement mode.
In the External Coupler measurement mode and the External Bridge impedance measurement
mode both receivers are connected to the input Channel 1 and Channel 2. Therefore all three ports of
Bode 100 must be used in these measurement modes.
A directional coupler or a resistive measurement bridge is never ideal and therefore introduces errors
caused by e.g. the frequency response of the coupler or bridge. By using Open, Short and Load
calibration, a Reference plane at the output of the coupler or bridge can be established such that all
frequency dependencies of the coupler or bridge are compensated. In the following example we show
how to remove an external measurement bridge by performing Open, Short and Load calibration at
the measurement port of the bridge. The same method can be applied to a directional coupler having
forward and reflected ports.
The External Coupler measurement mode as well as the External Bridge measurement
mode require an impedance calibration. You cannot start a measurement without having
performed Open, Short and Load calibration.
Figure 8-5: Removing a coupler / bridge by performing Open, Short and Load Calibration
86 OMICRON Lab
Calibration
OMICRON Lab 87
8.3.3 Calibrating an Impedance Adapter measurement
In this section you learn how to calibrate an Impedance, Reflection or Admittance measurement in the
Impedance Adapter measurement mode.
In the External Coupler measurement mode and the External Bridge impedance measurement
mode both receivers are connected to the input Channel 1 and Channel 2 at the front panel of
Bode 100.
The Impedance Adapter measurement mode is designed for component impedance measurements
performed with the B-WIC and B-SMC impedance test-fixtures from OMICRON Lab.
B-WIC and B-SMC contain a resistive measurement bridge, which is specifically optimized for
Bode 100.
The Impedance Adapter measurement mode requires impedance calibration. You cannot
start a measurement without having Open, Short and Load calibration performed.
Figure 8-6: Calibrating the B-WIC impedance test fixture by performing Open, Short and Load
Calibration
The following pictures show how to perform Open, Short and Load calibration steps for the B-WIC and
B-SMC impedance test fixtures. Note that in the Impedance Adapter measurement mode the default
value for Load Resistor is 100 Ω and the default value for Short Delay Time is 0 ps.
88 OMICRON Lab
Calibration
OMICRON Lab 89
8.3.4 Calibrating a Shunt-Thru or Series-Thru measurement
In this section you learn how to calibrate an Impedance, Reflection or Admittance measurement in the
Shunt-Thru or Series-Thru measurement mode.
Shunt-Thru and Series-Thru are based on a S21 Transmission measurement. Bode 100 measures
S21 and the Bode Analyzer Suite calculates impedance from the S21 measurement. Details on the
calculation can be found in 7.2.3 Shunt-Thru on page 69 and 7.2.5 Series-Thru on page 72.
You can either calibrate the underlying S21 measurement using Thru calibration or you can use Open/
Short/Load calibration to move the reference plane directly to the DUT.
Calibrating Open/Short/Load:
Open calibration.
90 OMICRON Lab
Calibration
Short calibration.
Note that the inductance of the short connection
is assumed to be zero. Short Delay Time is 0 s by
default. This means that inductance of the short
connection will be subtracted from the
measurement result. This might be important to
consider when you try measuring several nH of
parasitic inductance.
Load calibration.
Default Load Resistor value is 50 Ω.
Calibrating Open/Short/Load:
Open calibration.
Note that the capacitance of the Open is
assumed to be zero. If you try to measure very
low capacitance, the parasitic capacitance of the
Open can introduce an error. Try keeping it as
small as possible.
Short calibration.
Note that the inductance of the short connection
is assumed to be zero. Short Delay Time is 0 s by
default.
OMICRON Lab 91
Load calibration.
Default Load Resistor value is 50 Ω.
For more details and practical examples on how to perform calibration in the Shunt-Thru or Series-
Thru measurement mode, please refer to the corresponding application notes on www.omicron-
lab.com.
92 OMICRON Lab
Calibration
Calibrating Open/Short/Load:
Open calibration.
Short calibration.
Note that the inductance of the short connection
is assumed to be zero. Short Delay Time is 0 s by
default.
Load calibration.
Default Load Resistor value setting is 50 Ω.
For more details and practical examples on how to perform calibration in the Voltage/Current
measurement mode, please refer to the corresponding application notes on
www.omicron-lab.com.
OMICRON Lab 93
Figure 8-7: User-Range calibration; measurement frequencies and calibration frequencies are
congruent.
Figure 8-8: Full-Range calibration; correction factors are interpolated at measurement frequencies.
If Full-Range calibration is applied, the correction factors are available at the pre-defined frequencies
only. Correction factors for the measurement frequencies are calculated by interpolating between the
measured points.
94 OMICRON Lab
Calibration
Full-Range Gain calibration is not performed (not available) and not active.
The icon has no background fill and no border.
User-Range calibration and Full-Range calibration can be performed and activated at the
same time. However, if a valid User-Range calibration has been performed, the Bode
Analyzer Suite will automatically choose the User-Range calibration to be active.
Example:
OMICRON Lab 95
8.4.3 Re-performing a calibration
A calibration can be performed by clicking on the corresponding calibration icon in the Home ribbon.
• Clicking on a calibration icon (e.g. Full-Range Gain calibration ) opens the calibration
dialog
• The calibration icon turns green indicating that the calibration is now active .
From now on, this calibration is used for the measurement.
To re-performed a calibration, open the calibration dialog by clicking on the arrow on the
If you decide that frequencies between 1 Hz and 10 Hz must be included in the Full-Range
calibration, you must set the Start Frequency to a value <10 Hz before executing the Full-
Range calibration.
If a Full-Range calibration has been performed at a Start Frequency >10 Hz and Start
Frequency is changed to a value <10 Hz after calibration, the correction value at 10 Hz
will be extrapolated to 1 Hz. This is indicated by an orange Full-Range calibration icon.
Re-performing calibration will run the calibration from 1 Hz and the icon will turn green
again.
Note that the calibration takes significantly longer when it starts at 1 Hz.
96 OMICRON Lab
Calibration
The Bode Analyzer Suite attempts to load the calibration from the bode-file even when the
calibration has been performed with a different Bode 100 device.
OMICRON Lab 97
9 Bode Analyzer Suite functions
The following chapters contain information about important features of the Bode Analyzer Suite. Read
through these chapters to learn how to use Bode 100 efficiently.
This functionality allows you to store multiple equipment configurations for repetitive
measurement tasks. With the equipment configurations stored, you can load the respective
files for each measurement instead of setting the Bode 100 manually.
A file saved by the Bode Analyzer Suite 3 has the file extension .bode3. The Bode Analyzer Suite 3
supports loading files with the following file extensions:
• .bode3 files created with Bode Analyzer Suite 3
• .bodex files created with Bode Analyzer Suite 2.42 or 2.43
• .bodz files created with Bode Analyzer Suite 2.41
• .bode files created with Bode Analyzer Suite 2.41 or older
You can save and load .bode3 files on different Bode 100 devices. Note, however, that
calibration data might be deleted when opening the .bode3 file with a different hardware
revision. More details can be found in Hardware incompatibilities between Bode 100 R1 and
Bode 100 R2 on page 97.
98 OMICRON Lab
Bode Analyzer Suite functions
This will place an image file of the clicked diagram to the Microsoft Windows clipboard that can be
pasted to e.g. Microsoft Word. All frequency sweep charts, fixed frequency charts and the shaped
level chart can be copied as an image to the clipboard.
Hint: You can configure how the chart image looks like by using the Options →
Clipboard.
OMICRON Lab 99
Copy trace data to the clipboard
Right-click either in the chart or directly on the trace name to copy the measured data to the clipboard.
Copied data can directly be pasted in a spreadsheet program for further
data processing.
Hint: You can configure the decimal separator and the field separator under Options →
Clipboard.
Right-click in the chart and select . This will copy a text block to the
clipboard that contains the current equipment settings. The text block is similar to the settings header
included in the CSV or Excel file export.
Include settings header Include a header in the csv file that contains device
settings.
Note: The height of the header is not constant. Please
take care when parsing the csv file automatically.
Include active memory traces All memories that are currently visible in the Bode
Analyzer Suite will be exported to the csv file.
Include output level Includes the output level as the second column (after
frequency) of the csv file. Might be important for shaped
level measurements.
Include real & imaginary values Real and Imaginary are included independently of the
currently chosen display format in the GUI.
Decimal separator Choose your decimal separator of choice.
Field separator Configure the separator between two values / fields.
Open file after saving Activate this function to open the exported file with an
external program. When activated a text box appears
that allows you to choose your program file. Leave the
text box empty to use the default Windows program.
Press this button to store your settings for future
exports. You can find the default settings also in the
options dialog accessible in the main window via .
Press the Save as button to specify a file name and
save your export file.
Include settings header Include a header in the csv file that contains device
settings. Note: The height of the header is not constant.
Please take care when parsing the csv file
automatically.
Include active memory traces All memories that are currently visible in the
Bode Analyzer Suite will be exported to the csv file.
Include output level Includes the output level as the first column of the csv
file. Might be important for shaped level measurements.
Include real & imaginary values Real and Imaginary are included independently of the
currently chosen display format in the GUI.
Open file after saving Activate this function to open the exported file with an
external program. When activated a text box appears
that allows you to choose your program file. Leave the
text box empty to use the default windows program.
Press this button to store your settings for future
exports. You can find the default settings also in the
options dialog accessible in the main window via .
Press the Save as button to specify a file name and
save your export file.
You can change the source mode either in the hardware setup or by moving the mouse over the
source indicator in the status bar .
The source indicator shows both, the current setting and if the source is on or off. A gray background
indicates that the source is switched off. A green background color indicates that the signal source is
running. The following states are possible:
You can also choose Vrms or Vpp as output unit however, please don't forget that the real
output voltage of Bode 100 depends on the impedance connected to the output. The inner
50 Ω source impedance of Bode 100 introduces a voltage drop that depends on the
impedance connected at the output port.
The output level unit can be changed in the options. Click on and select the default level unit of
your choice: .
You can choose Vrms which is the root mean square of the output voltage at 50 Ω load. Again the real
output voltage depends on the load you connect to the output. The internal source voltage is 2 times
higher than the displayed value. Choose Vpp to display the output voltage in peak-to-peak voltage.
Again, the value is valid when a 50 Ω load connected to the output.
Changing the level unit only affects new files / measurements that are created after changing
the unit. The level unit is part of the settings stored in the .bode3 file.
Shaped level
The shaped level feature of Bode 100 allows changing the output level over frequency.
To use the shaped level feature, click on the slider selector to switch between constant and variable
level .
After switching to variable, the Output level text field changes its name to Reference level and the
In the shaped level dialog you can perform the following actions:
1. Interactive shaped level diagram
Shows the shaped level curve. Use your mouse to enter new shaped level points by double-
clicking or right-clicking into the diagram. Shaped level points can be moved by drag-and-drop in
the diagram. The blue line in the diagram shows the reference level line which allows you to shift
the entire shaped level curve up and down.
2. Shaped level points table
The table contains all shaped level points. Points added via mouse click into the diagram will show
up in the table. You can also use the table to enter new points manually.
3. Reference level
The reference level allows you to shift the entire shaped level curve up and down by either
entering a different reference level value or by moving the blue reference level line in the diagram.
Figure 9-2: Output level limited to the minimum output level of the device
It is not always possible to display two traces in one diagram. If one of the two traces is set
to a Polar, Smith or Nyquist diagram, automatically two diagrams will be displayed.
Figure 9-4: Displaying two traces in a separate diagram setting the chart setup to One axis per chart
Figure 9-5: Zooming in by click and drag from top-left to bottom right
Whenever you have zoomed in the diagram, the axis label shows additional arrows to indicate that a
zoom is active.
Figure 9-6: Zooming out by click and drag from bottom-right to top-left
Alternatively you can right-click into the chart and use the function in the context
menu of the chart as shown below.
Figure 9-7: Increasing the frequency resolution in a zoom window using Get from zoom
Figure 9-8: Manually configuring the axis limits via the trace configuration
Diagrams such as Polar, Nyquist or Smith have more axis settings to allow to choose the
visible range in the diagram.
If you don't want to click every time the measurement curve changes, you can use the
function available in the context menu of the chart.
When activated, automatically adjusts the axis limits whenever the measurement
results change. To display that the Auto Optimize is activated, the Ymax and Ymin text color is
changed to green :
Reset axes
If you want to reset the chart axes to the default values, right-click into the chart and use
.
• Switch cursors on and off by clicking on the checkbox besides the cursor name .
• Set the cursor frequency by clicking into the frequency field and manually entering a frequency
.
• Move the cursor to a specific measurement result by entering the desired value in the Trace
column .
• You can also enter a delta value and the second cursor will try to find a frequency where the delta
value can be achieved.
If an entered value cannot be found, the following information is shown.
.
If multiple solutions are present (e.g. more than one zero-crossing and you entered 0 into the cursor
grid), you can right click into the cursor grid and click to search the next solution from
the current frequency to right (higher frequency).
Hint: Jump to max or min always searches the global max or min in the visible chart region.
To find a local max or min, you can zoom into that region and re-perform Jump to Max.
Figure 9-11: Using memory curves to see changes in the measurement and to compare different
curves
You can use multiple memories to determine the change of your DUT depending on a parameter. The
following figure shows an example of how the parallel resonance frequency of the quartz filter changes
when touching it.
Hints:
• Double-clicking the Memory name allows you to change the name of the memory.
• When you hover over the memory name on the memory configuration box, the
corresponding memory curve will be highlighted in the diagram.
The memory configuration box gives you information on when the memory was stored and allows you
to control the memory curves.
• Click the checkbox next to the name to switch the memory curve on or off.
• Right-click the green area and use the context menu to change the memory style or color.
• Update the memory data with the current measurement data by clicking .
Options
The following options can be configured in the memory options. Go to the options dialog and select
Increasing the number of memory traces might impact your software performance.
Especially when you use a high number of points and many memory traces.
• Confirm the deletion of memory traces: When this checkbox is checked, the software will ask
for confirmation when deleting a memory trace.
• Default memory line pattern: Change the memory line styles according to your preference.
• Alternating memory trace color mode: Activate this option to color-code the memory curves
with the corresponding trace color. With this mode it is easier to distinguish between multiple
memories when more than one trace is shown in a diagram.
The Trace configuration box allows you to perform the following settings:
• Measurement: Configure what measurement the trace performs. Depending on the measurement
mode you can select between Gain, Impedance, Reflection and Admittance.
• Display: Choose if you want to see the measurement result, a math result or only the memory
curves.
• Format: Choose the desired result format how to display the measurement or math result. For
more details on the possible result formats, please refer to Gain Result Formats on page 41 and
Impedance Result Formats on page 42.
• Axis limits: Configure the axis limits of the diagrams. Please check out: 9.3.3 Optimize the axis
scaling on page 112.
• Y-axis scale: Choose either a linear Y-axis or a logarithmic Y-axis. In addition you can set it to
Log(|Y|) to avoid the logarithms of negative numbers.
• Disable or enable the measurement trace by clicking on the check-box besides the trace name
.
• Rename the trace by double-clicking on the trace name.
• Change the trace style (color, line style, trace markers) by right-clicking on the trace header area.
You can choose the two operands and the operator. The measurement data as well as memory data is
available as operand. The available operators are: +, -, *, /.
Notes:
• The operation is always performed on the complex measurement or memory value. The
display format is later on derived from the outcome of the math result.
• Please note that a division equals a subtraction in logarithmic domain. So if you choose
Measurement / Memory 1, in the Magnitude(dB) plot you will see the difference between
Measurement and Memory 1 in dB.
• A multiplication equals an summation in logarithmic domain. So if you choose
Measurement * Memory 1, in the Magnitude(dB) plot you will see the sum of
Measurement and Memory 1 in dB.
• If the frequency points of the two operands don't match, an info icon will be shown in the
trace header . Either linear interpolation will be used to find the needed
operand values or the values will be skipped.
As a next step, follow the instruction in the GUI and place Cursor 1 to the peak in the Q(Tg) result. The
phase margin calculation method shows the phase margin result in the cursor ribbon as shown in the
following figure:
To measure the resonance frequency and Q-factor of a resonance curve, go to the cursor ribbon and
select the Fres-Q calculation method as shown below:
As a next step, select the format and trace you want to use for the cursor calculation from the ribbon
interface as shown in the example below:
In this example we want to calculate the resonance frequency and Q-factor based on the Real part of
the values in Trace 1. As an alternative also the Magnitude can be used. If multiple traces contain
values or if a memory is linked to the cursor table, then the calculation can also be applied to these
curves.
Figure 9-14: Contactless resonance frequency and q-factor measurement of a 125 kHz RFID tag
The result in this example indicates a resonance frequency of 129.25 kHz and a Q-factor of 24.5.
To learn more about contactless resonance frequency and Q-factor measurements of RFID
transponders, please refer to the corresponding application note available at www.omicron-
lab.com/BodeManualAppNotes.
9.8 Averaging
Bode Analyzer Suite offers averaging to reduce measurement noise.
Averaging can be activated by clicking on the Average measurement icon in the View ribbon.
When averaging is active, the icon turns green.
The average factor influences the averaging method. A higher average factor offers a higher noise
reduction but requires more sweeps to complete.
The following figure shows an example where a Gain measurement is averaged (Green icon) and 4
sweeps have already been completed. The average factor is set to 10. Six more sweeps should be
completed to achieve the full noise reduction in this case.
The new averaged result is calculated using the new measured value and the previous averaged
result. N is the average factor that must be ≥2.
The influence of an old measurement will become lower and lower but will never completely
disappear (exponentially decaying moving average).
If your measurement result has changed, you can use Reset averaging to restart the
averaging and remove the influence of previous measurement results.
Averaging is performed sweep to sweep. This means that at least 2 sweeps are necessary to calculate
an averaged result.
Averaging is calculated using the complex measurement result.
Memory traces
Whenever you activate averaging, two memory buttons are available to copy data to the memory
traces.
WARNING
Check safety instructions before measuring circuits connected to or producing
hazardous voltages >50 VDC or >25 VAC.
NOTICE
Bode 100 inputs are AC coupled with a maximum allowed DC voltage of 50 VDC. A standard,
passive, 10:1 probe with 9 MΩ tip-resistor cannot be used to connect Bode 100 to higher DC
voltages! The DC-voltage will not be divided by 10 can destroy the AC coupling capacitor and
damage the input circuitry!
1 MΩ 10:1 probes are recommended. 1 MΩ probes feature a divider in the probe that lowers
DC voltage as well. Furthermore 1 MΩ probes provide a lower impedance path that reduces
channel-channel crosstalk and noise.
If a probe has a different probe factor than 1:1, you can configure the probe factor in the hardware
setup dialog for each channel separately. To do so, enter the hardware setup dialog by clicking on the
To configure the probe factor, you can use the combo-box. Click on the arrow and select one of the
pre-defined probe factors:
Alternatively you can enter an arbitrary probe factor by marking the text and entering your probe ratio
as shown in the examples below:
Figure 9-16: Phase-wrap effect caused by the fact that phase can only be measured between -180°
and +180°
Figure 9-17: Unwrapped phase result shows the total phase shift of the IF filter DUT
Hint: Optionally you can limit the unwrapping to a specific frequency range. Use the Begin
and End check boxes and corresponding entry fields to define a frequency range in that the
phase shall be unwrapped. This is especially useful when the phase result contains a lot of
noise in a specific frequency range.
If a newer version is available, the Bode Analyzer Suite will inform you by showing an
information screen.
NuGet package
If you are a .NET developer, you might be interested in using the Automation Interface in form of the
NuGet package OmicronLab.VectorNetworkAnalysis.AutomationInterface.
In any case the installation of the Bode Analyzer Suite or the Bode Automation Interface is
required! The installation will install the USB driver that is needed to access Bode 100.
For more information regarding automating the Bode 100, check out our web page:
www.omicron-lab.com or have a look at the Automation Interface reference available online at:
www.omicron-lab.com/BodeAutomationInterfaceHelp.
11 Troubleshooting
Connection issues
In case you are not able to start a measurement with Bode 100, please check the following points:
1. Check if the green power LED at the front panel is on.
In case that the LED is not lit execute the following steps:
a. Check if the Wide-range AC power supply is plugged correctly into the mains socket.
b. Check if the DC connector of the power supply is properly plugged into the Bode 100.
c. Check the output voltage of the DC connector with a volt-meter.
2. Check if the communication between the Bode Analyzer Suite and the Bode 100 has been
successfully established. To do so, check if the serial number of your Bode 100 is displayed in the
start screen (see figure6-1 on page 23, or the right bottom corner of the main window
(see figure6-2 on page 24). In case you cannot see any Bode 100 serial
number, please execute the steps below:
a. Check if the USB cable is properly plugged into the computer and the Bode 100.
b. Try disconnecting and re-connecting the USB cable.
c. If this does not help, avoid USB hubs and plug Bode 100 directly into an USB port of your
computer.
d. Try to connect Bode 100 to a different USB port of your computer. Some USB 3 ports are
known to have problems with Revision 1 of Bode 100.
e. Move the mouse over the icon in the status bar and then click
Software problems
In case you run into software issues such as crashes or unexpected behavior, please contact the
OMICRON Lab Support.
To help the support team, you can include the log file of the Bode Analyzer Suite in your support
request. The log file is normally located at: C:\ProgramData\OMICRON Lab\Bode Analyzer\Logs\Bode
Analyzer Suite.log.
In case you are still experiencing problems do not hesitate to contact us. We are looking
forward to support you. Check out the following Support section for further information on
how to contact us.
www.omicron-lab.com/support
[email protected]
At our technical support hotline, you can reach well-educated technicians for all of your questions.
Competent and free of charge.
Make use of our technical support hotlines:
Additionally, you can find the OMICRON Lab Service Center or Sales Partner closest to you at
www.omicron-lab.com → Contact.
OMICRON Lab
OMICRON electronics GmbH, Oberes Ried 1, 6833 Klaus, Austria. +43 59495.
Index
Chart
.bode file ...................................................... 98
Context menu ......................................... 33
.bode3 file ................................................... 98
Chart ......................................................... 107
.bodex file ................................................... 98
Cleaning ...................................................... 11
COM ......................................................... 134
A Compensation ............................................ 75
B D
Block diagram ............................................. 21
Data / Memory ........................................... 121
B-SMC ........................................................ 64
Deletion of calibration .................................. 97
B-WIC ......................................................... 64
Delivered Items ........................................... 13
Disposal ...................................................... 12
C
Calibration ............................................. 75, 96 E
Full-Range .............................................. 75
Email (OMICRON Lab email address) ..... 136
User-Range ............................................ 75
Examples ..................................................... 23
Calibration ........ 75, 84, 86, 88, 90, 92, 95, 96
Excel ......................................................... 100
J
F Jump to Max .............................................. 115
Factory calibration ...................................... 75 Jump to Zero .............................................. 115
Features ...................................................... 98 Jump to Min ............................................... 115
Fres-Q ....................................................... 125
Full-Range ................................................... 75
Full-Range ...................................... 93, 95, 96
L
LabVIEW .................................................. 134
Function principle ........................................ 22
Level unit .................................................. 104
Loop Gain ................................................... 52
G
Gain Calibration .......................................... 76
Gain/Phase ................................................. 52
M
Matlab ....................................................... 134
Get from zoom .......................................... 109
Measurement configuration ........................ 26
Measurement modes ................................... 39
H External coupler .................................... 53
External Bridge ...................................... 74
Hardware setup .......................................... 37
Gain/Phase ............................................ 52
Hotline ...................................................... 136
Impedance Adapter ............................... 64
One-Port ................................................ 54
I Series-Thru ............................................
Shunt-Thru ............................................
72
69
Icons ........................................................... 30 Shunt-Thru with series resistance ......... 71
Impedance Adapter .............................. 64, 88 Transmission / Reflection ...................... 46
Voltage/Current ..................................... 73
Impedance Analysis
Impedance Adapter ................................ 64 Measurement trace .................................... 121
Shunt-Thru with series resistance ......... 71 Memory curves .......................................... 117
Impedance calibration ................................ 81 Memory traces .......................................... 117
Impedance Measurement
Result formats ................................. 40, 42
Impedance Analysis
N
One-Port ................................................ 54 NISM .......................................................... 123
Shunt-Thru ............................................. 69 Noise reduction .......................................... 127
R
Recycling .................................................... 12
Reflection .................................................... 84
U
Unwrap phase ........................................... 131
Update informer ......................................... 133
User-Range ................................................. 75
User-Range .......................................... 93, 95
V
Voltage/Current ..................................... 73, 92
W
Web (OMICRON Lab website) ................. 136
Welcome screen ......................................... 23
Window ....................................................... 24
[email protected]
www.omicron-lab.com