Scribd Logo
Upload

Welcome to Scribd!

  • 12 views

    ME 3301 1113 Revision Assignment

    Uploaded by

    engineer.mohammedtahhan

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Flag for inappropriate content

    ME 3301 1113 Revision Assignment

    Uploaded by

    engineer.mohammedtahhan
    12 views14 pages

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Flag for inappropriate content
    Download as pdf or txt
    12 views14 pages

    ME 3301 1113 Revision Assignment

    Uploaded by

    engineer.mohammedtahhan

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Flag for inappropriate content
    Download as pdf or txt
    of 14

    Islamic University ‫اجلامعة اإلسالمية‬

    Faculty of Engineering
    Department of
    ‫كليه اهلندسة‬
    Mechanical Engineering ‫قسم اهلندسة امليكانيكية‬

    ME 3301_1113

    Mechanical Engineering Drawing

    Date (6th March 2022)

    Submission Date: 9th March 2022

    Revision/Reinforcement Assignment

    Name of the Student: _____________________________________

    ID #: ___________________________________________________

    Question No. CO/PI Maximum Marks Awarded


    Marks
    1 CO 1: [abet_PI_6_39] 100
    2 CO 2:[abet_PI_6_40] 100
    3 CO 3:[abet_PI_6_38] 50
    4 CO 3:[abet_PI_6_43] 50
    Score 300

    Final submission will be accepted in a single pdf file.


    Caution:
    • ONLY Handwritten/handsketched answers acceptable
    • Copying among students/copying material from internet will be penalised

    Page 1 of 14
    Q.1.
    1.a) Explain the following 2D Drafting AutoCAD Commands/Geomtric entities with 3 x 20
    the help of hand sketched simple line diagrams. (The explanation should contain
    step-wsie execution of these commands). (2 points for Explanation, 1 Point for
    Line Diagram)
    i) Line at any angle
    ii) Circle ( Center-Radius | 2-Point | 3 Point | Tan-Tan_Radius )
    iii) Polygon
    iv) Ellipse
    v) Isocircle
    vi) Move
    vii) Rotate
    viii) Trim/Extend
    ix) Offset
    x) Mirror
    xi) ArrayRect
    xii) ArrayPolar
    xiii) Scale
    xiv) Fillet
    xv) Chamfer
    xvi) LineType Scale
    xvii) Match Properities
    xviii) Hatch (Angle and Scale)
    xix) Align
    xx) Draw Order

    Page 2 of 14
    Space for Q.1.a)

    Page 3 of 14
    Space for Q.1.a)

    Page 4 of 14
    Space for Q.1.a)

    Page 5 of 14
    1.b) Explain the utility of the following highlighted fields in the dimstylemanager. 3 x 10
    Take help of simple diagrams and dimensions to show before and after effects.

    Page 6 of 14
    Page 7 of 14
    Page 8 of 14
    Page 9 of 14
    1.c) Make a detailed flow chart for the procedure you follow for 10
    plotting a drawing in AutoCAD in a pdf file.

    Page 10 of 14
    Q.2. 2.a) 4 x 10
    Explain the purpose of the following standard line types in Engineering Drawing
    in your own words.

    Page 11 of 14
    2.b) Sketch the standard represenetation and dimensional entities for the following hole 10 x 2
    types.
    i) Countesunk Hole
    ii) Counterbore Hole

    Page 12 of 14
    2.c) Draw the standard symbols/indications in Engineering drawing for the following 8x5
    tolerancing parameters. Also provide their interpretations.
    i) Straightness
    ii) Flatness
    iii) Circularity
    iv) Perpendicularity
    v) Symmetry

    Page 13 of 14
    Q.3. a) Produce an orthographic representation of the following component in 1st Angle 50+50
    Projection.
    b) Reproduce the component in Isometric Projection with dimensions.

    Page 14 of 14

    You might also like