PHY (UNIT 4) (NOTEs)
PHY (UNIT 4) (NOTEs)
Syllabus
- Free electron theory (Qualitative)
- Opening of band gap due to internal electron diffraction due to lattice
- Band theory of solids
- Effective mass of electron
- Density of states
- Fermi Dirac distribution function
- Conductivity of conductors and semiconductors
- Position of Fermi level in intrinsic and extrinsic semiconductors (with derivations based on
carrier concentration)
- Working of PN junction on the basis of band diagram
- Expression for barrier potential (derivation)
- Ideal diode equation
- Applications of PN junction diode: Solar cell (basic principle with band diagram) IV
Characteristics and Parameters, ways of improving efficiency of solar cell
- Hall effect: Derivation for Hall voltage, Hall coefficient, applications of Hall effect
Page 1 of 27
(c) The theoretical values of mean free path of electrons as calculated from this theory do not
agree with experimental values.
(d) The theoretical values of specific heat and electronic specific heat as calculated from this
theory do not agree with experimental values.
(e) Some metals such as zinc have positive values of Hall effect. This theory could not explain
why zinc and other metals have positive value of Hall coefficient.
(f) Wiedemann-Franz law deviates at low temperature.
𝑑2 2𝑚
Schrodinger’s equation in one dimension + 2 (𝐸 − 𝑉) = 0
𝑑𝑥 2 ℏ
𝑑2
Above equations can be written as 𝑑𝑥 2
+ 𝛼 2 = 0 for 0 < 𝑥 < 𝑎,
2𝑚𝐸
where 𝛼 = √ ℏ2
Solution using Bloch Theorem
The solution of the Schrodinger’s equation for a periodic potential can be found using Bloch
theorem, which is
𝑚𝑎𝑉0 𝑏 sin 𝛼𝑎
( ℏ2
)( 𝑎
) + cos 𝛼𝑎 = cos 𝑘𝑎
The above equation provides allowed solutions to the Schrodinger’s equation. Due to cosine term,
the right hand side varies between +1 and -1 and so left hand side is also allowed to vary between
2𝑚𝐸
these two values. Thus, only certain values of are possible. As 𝛼 = √ ℏ2
, the energy E is restricted
to lie within certain ranges.
Page 2 of 27
Energy vs wave number
The relation between energy E and wave number k is a parabolic. The motion of free electron is
interrupted at certain values of k, as shown by the broken curve.
𝜋 2𝜋 3𝜋
The plot also shows discontinuities in Energy of electron at 𝑘 = ± 𝑎 , ± 𝑎 , ± 𝑎
These gaps correspond to energy bands inside the solids. Thus, the energy level of electron in the
crystal lattice is discrete.
Page 3 of 27
Valence Band
- The valence band is energy band formed by
grouping the range of energy levels of the
valence electrons that are engaged in
covalent bonding.
- In the solids, valance electrons are not
bound to any particular atom therefore, the
valance band arises from splitting of the
valance energy levels. It is common to the
entire solid.
Conduction band:
- Conduction band corresponds to the energy values of free electrons that have broken their
valence bonds and hence become free to move in the solid. It is formed by grouping the
range of energy levels of the free electrons. It is also common to the entire solid.
- The bottom of the conduction band represents the smallest energy that the electron must
possess to become free.
(a) Metals/Conductors
- In some solids a large numbers of free electrons are randomly moving in the entire solid that
belong to conduction band. These free electrons also form a temporary bond with closest ion
and are said to belong to valence band.
- Thus valence bands and conduction bands overlap and bandgap energy is zero. Electrons in
the valence band can easily move to conduction band.
- Such solids are called conductors. The examples are metals such as copper, aluminum, silver,
gold etc. Concentration of Free electrons is about 1028 electrons/m3.
- When an electrical field is applied, these large numbers of electrons easily readily jump into
conduction band and current flows in a large quantity.
- The resistivity of conductors is in between 10-8 to 10-6 (-m). The conductivity is typically of
the order of 107 (mho/m).
(b) Semiconductors
- In some solids, band gap is narrow and it is of the order of 2 eV or less. Valence electrons
acquire a small amount of energy from the vibrations of atoms and can move from valence
band to the conduction band. Thus conduction band is partially filled.
- If a potential is applied across the material, a moderate number of electrons in valence band
Page 4 of 27
jumps to conduction band. Hence current flows in a modest proportion.
- Such solids are called semiconductors e.g. silicon, germanium, etc. Free electron density is
about 1014 electrons/m3 which is very less as compared to metals.
- The resistivity of semiconductors varies from 10-4 to 10 ohms-m which depend on several
factors such as doping concentration, temperature, etc. The conductivity is typically varies
from 10-6 to 104 (mho/m).
(b) Insulators
- In some solids band gap energy is very wide (>5eV). The electrons are tightly bounded to
atoms and it would require very large amount of energy to raise an electron from valence
band to conduction band. Very few electrons can get this large amount of energy at ambient
temperature. Hence there are only a few electrons present in the conduction band.
- When potential difference is applied across them a negligible current flows and solid exhibits
very low electrical conductivity.
- Such solids are called insulators e.g. glass, wood, mica, etc. The free electron density is
negligible.
- The resistivity of insulators vary from 1012 to 1016 (-m) and conductivity is typically 10-12
(mho/m).
Page 5 of 27
𝑑2 𝐸
(ii) At the point of inflection B, the derivative 2 = 0. Hence in these regions m* . It means
𝑑𝑘
that an external field cannot exert any action on the motion of the electron in this region.
𝑑2 𝐸
(iii) Near the top of the allowed band, the derivative 𝑑𝑘 2 < 0. Therefore, the effective mass of
electron m* occupying levels near the top of the band is negative.
The number of states lying in the range of energies between 𝐸 and 𝐸 + 𝑑𝐸 is given by
4𝜋
𝑔(𝐸)𝑑𝐸 = 3
(2𝑚)3/2 𝐸1/2 𝑑𝐸
ℎ
The function 𝑔(𝐸) is known as density of states function.
Page 6 of 27
4.6 Electrical conductivity in metals
The conductivity of a material can be related to the number of
charge carriers present in the material.
Then,
𝑄 𝑛𝑒𝐴𝐿
The current through the solid, 𝐼=𝑡= 𝑡 --- (2)
Or 𝐼 = 𝑛𝑒𝐴𝑣𝑑
𝑛𝑒𝐴𝑣𝑑
Or 𝐽= 𝐴
Or 𝐽 = 𝑛𝑒𝑣𝑑
V
Now I=
R
𝐿 𝑉𝐴 1𝑉
But 𝑅 = 𝜌 , Hence 𝐼= = 𝐴
𝐴 𝜌𝐿 𝜌𝐿
The quantity is known as mobility of electrons. It indicates the ease with which electrons move in a
solid. It is defined as the drift velocity per unit electric field. The unit of mobility is m2/V.s. In metals
it is of the order of 10-3 m2/Vs and in semiconductors it is of the order of 10-1 m2/V.s.
Page 7 of 27
4.7 Electrical conductivity in semiconductors
Let us consider a sample of semiconductor across which a dc
voltage source is connected. If a potential difference is applied
across semiconductor, it generates an electric field. This causes
electrons to move towards the positive terminal and holes towards
the negative terminal of the source.
The total current density is J is given by J=I/A, where A is cross-sectional area of the sample
𝐼 𝑒𝐴𝐸(𝑛𝑒 𝜇𝑒 +𝑛ℎ 𝜇ℎ )
Thus, 𝐽=𝐴= 𝐴
This expression gives the electrical conductivity of a typical semiconductor. In general, it is linked to
the variation of mobility with temperature is too small and the large variation in electrical
conductivity is because of large variation of electron concentration with temperature.
Page 8 of 27
For a n-type semiconductor, the concentration of electrons is much greater than the concentration
of holes i.e.𝑛𝑒 ≫ 𝑛ℎ . The majority charge carriers are electrons and the contribution of holes is
neglected due to very small value.
Thus, conductivity of N-type semiconductor 𝜎𝑒 = 𝑒𝑛𝑒 𝜇𝑒
Page 9 of 27
4.8 Fermi energy and Fermi-Dirac distribution function
Fermions: Fermions are particles which have half-integer spin (like 1/2, 3/2,……) and are
indistinguishable particles. Fermions obey the Pauli Exclusion Principle and therefore cannot co-exist
in the same state at same location at the same time. Fermions include electrons, protons.
Case I: At T= 0K, for E<Ef (for the energy levels located below Fermi energy)
The quantity (E-Ef) in the equation is negative and the argument of the exponential function is -.
1 1
Thus, 𝑓(𝐸) = = 1+0 = 1
1+𝑒 −∞
f(E)=1 implies that all the levels below Ef are occupied by
electrons.
Case II: At T= 0K, for E>Ef (for the energy levels located
above Fermi energy)
The quantity (E-Ef) in the equation is positive and the
argument of the exponential function is +.
1 1
Thus, 𝑓(𝐸) = = 1+∞ = 0
1+𝑒 ∞
f(E)=0 implies that all the levels below Ef are vacant.
Case III: At T= 0K, for E=Ef (for the energy levels equal to Fermi energy)
1
The quantity (E-Ef) in the equation is zero. Thus, 𝑓(𝐸) = 1+𝑒 0/𝑜 is indeterminate.
Thus at Fermi level at T=0K, the occupation of electron has indeterminate value ranging between
zero and one.
Case IV: At T> 0K, for E=Ef (for the energy levels equal to Fermi energy above T=0K)
1 1 1
The quantity (E-Ef) in the equation is zero. Thus, 𝑓(𝐸) = = 1+1 = 2 = 0.5
1+𝑒 0
It implies that the probability of occupancy of Fermi level at any temperature above 0K is 0.5. Thus,
Fermi energy is the average energy possessed by the electrons which participate in conduction
process in conductors at temperature above 0K.
Page 10 of 27
4.9 Position of Fermi level in intrinsic semiconductor
The Fermi function f(E) gives the probability that the energy state (E) will be occupied by electron at
1
temperature (T). It is given as 𝑓(𝐸) = (𝐸−𝐸𝑓 )/𝑘𝑇 --- (1)
1+𝑒
Where, f(E) – Fermi function
E – energy of given state
Ef– Fermi energy
T – Temperature (in Kelvin) for the available state
k – Boltzmann’s constant, k=1.3806503 × 10-23 J/K0
For this derivation it is assumed that:
1. The widths of valance band and conduction band are small compared to the forbidden
energy gap Eg
2. All energy levels in conduction band have energy Ec, and all energy levels in valence band
have energy Ev.
Let nc- number of electrons in conduction band
nv- number of electrons in valence band
N- total number of electrons in both conduction and valence bands
1 1
Or 1= (𝐸𝑐− 𝐸𝑓 )/𝑘𝑇 + (𝐸𝑣− 𝐸𝑓 )/𝑘𝑇
1+𝑒 1+𝑒
𝐸 +𝐸 −2𝐸
Taking logarithm of both sides 𝑐 𝑣 𝑓 = 0
𝑘𝑇
Or 𝐸𝑐 + 𝐸𝑣 − 2𝐸𝑓=0
𝐸 +𝐸
Or 𝐸𝑓𝑖 = 𝑐 2 𝑣 --- (8)
Thus, Fermi level in intrinsic semiconductors is exactly in the middle of the forbidden energy gap
i.e.it indicates a reference level indicating the distribution of electrons and holes in intrinsic
semiconductors.
Page 11 of 27
Position of Fermi Level in Extrinsic Semiconductors (at 0K)
N-type semiconductor
- An intrinsic semiconductor is doped with a pentavalent donor impurity atom.
- The energy levels of donor atoms are very close to bottom of unfilled conduction band.
- The electrons donated by donor atoms enter into conduction band.
- The average energy of electrons increases. Thus, Fermi level shifts towards conduction band.
- At T=0K, EfN lies midway between the donor levels and the bottom of the conduction band
𝐸 +𝐸
i.e. 𝐸𝑓𝑁 = 𝑐 2 𝑑
P-type Semiconductor
- An intrinsic semiconductor is doped with a trivalent impurity atom and its energy levels are
very close to the top of filled valence band
- After doping, a deficiency of an electron is produced and it creates a hole in the valence
band.
- Thus, there is less number of electrons available in valence band the average energy of
electrons in valence band decreases. As a result Fermi level shifts down towards the valence
band.
- At T=0K, Fermi level lies midway between the acceptor levels and the top of the valence
𝐸 +𝐸
band. Thus, 𝐸𝑓𝑃 = 𝑣 𝑎
2
PN Junction diode
- A p-n junction diode is two-terminal semiconductor
device, which allows the electric current in only one
direction.
- If the diode is forward biased, it allows the electric
current flow. On the other hand, if the diode is reverse biased, it
blocks the electric current flow.
- When a junction is made between these materials, the electrons would tend to move from
n-type material to p-type material, which is known as diffusion
- The combining of electrons and holes depletes the holes in the p-region and the electrons in
the n-region near the junction. This region is known as depletion region.
- After formation of depletion region, the movement of electrons and holes across junction
stops and a potential barrier is created.
Page 12 of 27
4.10 Working of PN junction on the basis of band theory
I. Non Equilibrium State
A p-n junction diode is constructed by joining a P and N type semiconductors. When P and N type
semiconductors are in isolated from each other they are said to be in non-equilibrium state. Fermi
level of n-type semiconductor is located close to the bottom of the conduction band. Fermi level of
p-type semiconductor is located close to be top of the valence band.
At equilibrium
When equilibrium achieved, the movement of
electrons and holes across the junction stops
and a depletion region is formed. The band
edges in the two regions shift themselves so
that Fermi levels are properly aligned and
attain equilibrium. The Fermi level in N region
shifts down by an energy e.V0 whereas Fermi
level in P region shifts upward by the same
energy e.V0, where V0 is the potential barrier
across the junction.
After equilibrium is attained, the majority
electrons from N region face the potential
barrier across the junction. Thus they cannot
cross the junction and no current flows.
An external potential difference V is applied to diode in forward bias. This voltage should be greater
than potential barrier of V0. Now electrons from the source are added to N region. Hence potential
in N region rises by e(V0-V). The Fermi level of P region does down. Electrons in N region now face a
lower potential barrier. The width of potential barrier is reduced. Hence electrons from N region
cross the junction easily to enter into P region and electrons flow increases. This constitutes forward
bias current. This current increases with increase in forward bias.
Page 13 of 27
III. P-N junction under reverse bias
An external potential difference V is applied to diode in reverse bias. Due to this electrons are
removed from N region. Hence potential in N region decreases by e(V0+V). Electrons enter into P
region and hence potential in this region rises. Electrons in N region now face a higher potential
barrier. The width of potential barrier is increased. Hence electrons from N region cannot cross the
junction easily to enter into P region and electron flow decreases. However, small leakage current
flows through junction which constitutes reverse bias current.
The Fermi function f(E) gives the probability that the energy state (E) will be occupied by electron at
1
temperature (T). It is given as 𝑓(𝐸) = (𝐸−𝐸𝑓 )/𝑘𝑇 --- (1)
1+𝑒
Where, f(E) – Fermi function
E – energy of given state
Ef– Fermi energy
T – Temperature (in Kelvin) for the available state
k – Boltzmann’s constant, k=1.3806503 × 10-23 J/K0
𝑁𝑐
𝑛𝑛 = (𝐸𝑔− 𝐸𝑓 )/𝑘𝑇 --- (2)
1+𝑒
When number of particles is very small compared to the available energy levels, the probability of an
energy state being occupied by more than one electron is small. In this situation, (𝐸𝑔− 𝐸𝑓 ) ≫ 3𝑘𝑇.
Page 14 of 27
𝑁𝑐
Thus, 𝑛𝑛 = (𝐸 𝐸 )/𝑘𝑇 = 𝑁𝑐 𝑒−(𝐸𝑔− 𝐸𝑓 )/𝑘𝑇
𝑒 𝑔− 𝑓
Due to the barrier potential V0, the band gap energy on p-region increases by (Eg+eV0). The electron
concentration on p-side can be written as
𝑛𝑝 = 𝑁𝑐 exp[−{(𝐸𝑔 + 𝑒𝑉0 ) − 𝐸𝑓 }/𝑘𝑇] (2)
𝑛𝑛 𝑒𝑉
Dividing the two equations, we get 𝑛𝑝
= 𝑒𝑥𝑝 𝑘𝑇0 (3)
𝑛 𝑒𝑉0
Taking log of both sides, ln 𝑛𝑛 = 𝑘𝑇
𝑝
𝑘𝑇 𝑛
OR 𝑉0 = 𝑒
ln 𝑛𝑛 (4)
𝑝
If pp is concentration of holes in p-region, above equation can be written as
𝑘𝑇 𝑛 𝑝
𝑉0 = 𝑒 ln 𝑛𝑛𝑝𝑝 (5)
𝑝 𝑝
Let ND – concentration of donor atoms
NA – Concentration of acceptor atoms
At room temperature, all the impurities are ionized, hence: 𝑛𝑛 = 𝑁𝐷 , 𝑝𝑝 = 𝑁𝐴
Also, 𝑛𝑝 𝑝𝑝 = 𝑛𝑖2
𝑘𝑇 𝑁 𝑁
Thus, equation (5) can be written as 𝑉0 = 𝑒
ln 𝐷𝑛2 𝐴
𝑖
𝑘𝑇 𝑁𝐷 𝑁𝐴
The factor is of the dimensions of voltage and is denoted by VT, Thus 𝑉0 = 𝑉𝑇 ln
𝑒 𝑛𝑖2
Unbiased diode
(a) Current due to Diffusion
When P and N regions are brought together, due to concentration difference, holes in p-region
diffuse to n-region and electrons in n-region are diffuse to p-region.
Let, (𝐽𝑒 )𝑈𝐵
𝐷𝐹 – electron diffusion current density of unbiased diode
(𝐽ℎ )𝑈𝐵
𝐷𝐹 – hole diffusion current density of unbiased diode
Page 15 of 27
(b) Current due to drift
Due to potential barrier, electrons reaching the edge of the junction on p-side are accelerated by
electric field into n-region and similarly, holes reaching the edge of the junction on n-side are
accelerated into p-region.
Let, (𝐽𝑒 )𝑈𝐵
𝐷𝑅 – electron drift current density of unbiased diode
(𝐽ℎ )𝑈𝐵
𝐷𝑅 – hole drift current density of unbiased diode
𝑈𝐵 𝑒𝑉
And hole diffusion current density in forward bias = (𝐽ℎ )𝐹𝐵
𝐷𝐹 = (𝐽ℎ ) × 𝑒𝑥𝑝 ( 𝑘𝑇𝐹 )
𝐷𝐹
Under equilibrium
(hole diffusion current density) = (hole drift current density)
𝑈𝐵 𝑒𝑉𝐹 𝑈𝐵 𝑒𝑉𝐹
(𝐽ℎ )𝐹𝐵
𝐷𝐹 = (𝐽ℎ ) × 𝑒𝑥𝑝 ( ) = (𝐽ℎ ) × 𝑒𝑥𝑝 ( )
𝐷𝐹 𝑘𝑇 𝐷𝑅 𝑘𝑇
𝑈𝐵 𝑒𝑉𝐹 𝑈𝐵 𝑒𝑉𝐹
(𝐽𝑒 )𝐹𝐵
𝐷𝐹 = (𝐽𝑒 ) × 𝑒𝑥𝑝 ( ) = (𝐽𝑒 ) × 𝑒𝑥𝑝 ( )
𝐷𝑅 𝑘𝑇 𝐷𝐹 𝑘𝑇
The drift current density components have not changed and have the same magnitude as in
equilibrium case.
Let, (𝐽𝑒 )𝑁𝐸𝑇 - Net electron current density of unbiased diode
Therefore, the net hole current density across the forward bias junction is
𝐹𝐵
(𝐽ℎ )𝑁𝐸𝑇 = (𝐽ℎ ) − (𝐽ℎ )𝑈𝐵
𝐷𝑅
𝐷𝐹
𝑒𝑉 𝑒𝑉
(𝐽ℎ )𝑁𝐸𝑇 = (𝐽ℎ )𝑈𝐵 𝐹 𝑈𝐵 𝑈𝐵 𝐹
𝐷𝑅 × 𝑒𝑥𝑝 ( 𝑘𝑇 ) − (𝐽ℎ )𝐷𝑅 = (𝐽ℎ )𝐷𝑅 [𝑒𝑥𝑝 ( 𝑘𝑇 ) − 1]
Similarly,
𝑒𝑉𝐹
(𝐽𝑒 )𝑁𝐸𝑇 = (𝐽𝑒 )𝑈𝐵
𝐷𝑅 [𝑒𝑥𝑝 ( ) − 1]
𝑘𝑇
Let
𝐽𝑇𝑜𝑡𝑎𝑙 = Total current density across the forward bias junction
𝐽𝑇𝑜𝑡𝑎𝑙 = (𝐽ℎ ) + (𝐽𝑒 )𝑁𝐸𝑇
𝑁𝐸𝑇
𝑈𝐵 𝑒𝑉𝐹 𝑈𝐵 𝑒𝑉𝐹
𝐽𝑇𝑜𝑡𝑎𝑙 = (𝐽ℎ ) [𝑒𝑥𝑝 ( ) − 1] + (𝐽𝑒 ) [𝑒𝑥𝑝 ( ) − 1]
𝐷𝑅 𝑘𝑇 𝐷𝑅 𝑘𝑇
Page 16 of 27
𝑒𝑉𝐹 𝑈𝐵 𝑈𝐵
𝐽𝑇𝑜𝑡𝑎𝑙 = [𝑒𝑥𝑝 ( ) − 1] [(𝐽ℎ ) + (𝐽𝑒 ) ]
𝑘𝑇 𝐷𝑅 𝐷𝑅
𝑈𝐵 𝑈𝐵
Let, 𝐽0 = [(𝐽ℎ ) + (𝐽𝑒 )𝐷𝑅 ]
𝐷𝑅
𝑒𝑉
Or 𝐽 = 𝐽0 [𝑒𝑥𝑝 ( 𝑘𝑇𝐹 ) − 1]
Where, V denotes voltage (V=VF is for forward bias and V=-VR for reverse bias) and
I0 denotes reverse saturation current.
Photovoltaic Effect
- Photovoltaic effect is a process in which two dissimilar materials in close contact produce an
electrical voltage when light or other radiant energy incident on it.
- In crystals such as silicon or germanium, electrons are usually not free to move from atom to
atom. When light incident on crystal, the photons provides energy to some electrons to
become free from their bound condition. These free electrons cross the junction between
two dissimilar crystals more easily in one direction than in the other. This generates a
negative charge and negative voltage in one region as compared to other region.
- The photovoltaic effect can continue to provide voltage and current as long as light
continues to fall on the two materials.
- When the sunlight falls on the upper p-region, it generates the electron-hole pairs in both P
and N regions.
- Thickness of p-layer is small. Hence the probability of recombination of electrons and holes
is less and they immediately reach the PN junction.
Page 17 of 27
- At the junction, barrier potential attracts
electrons from p-region into n-region and holes
from n-region into p-region. This leads to an
increase in the number of holes on p-region and
electrons in the region.
- The accumulation of charges on the two sides
of the junction produces a voltage or EMF
known as photo EMF. It is known as the open
circuit voltage and is proportional to the
intensity of the incident light as well as size of
the illuminated area.
- If an external circuit is connected across the solar cell terminals, a current flows through the
circuit.
Where, Im and Vm are the values of maximum current and voltage obtained experimentally.
𝐼 ×𝑉
= Incident𝑚Light
𝑚
Power
Usually the voltage developed by a solar cell is of the order of 0.6V and the efficiency of
conversion is about 15-21% for silicon cells.
Page 18 of 27
Advantages of solar cell
1. Solar cells obtain energy from the sun and transform this into usable electricity.
2. Renewable energy - The energy can be used both to generate electricity and heat either
through solar PV system or solar thermal system.
3. Economy-friendly energy – Once the installation is made, solar cell can be operated at
almost no cost (except maintenance).
4. Environmentally friendly energy - Solar cells produces energy without pollution
5. Long term energy - PV systems often have a long life and a good durability.
6. Solar cells can be installed virtually anywhere; in a field to on a roof of building
Solar tracker
Solar tracker is the rotation of the panel so that it always directly faces the sun. However, larger the
array, more difficult will be the operation. The optimum tilt angle changes slowly as the earth
rotates on its axis
Page 19 of 27
Light Concentrators
Solar panel output power may be increased to almost 50% via a light concentrator such as a Fresnel
lens or mirror. However, installing concentrators for a large array of solar cells and orientation of the
mirror creates an additional tracking problem.
MPPT Controller
MPPT stands for Maximum Power Point Tracking. MPPT control does not turn the excess power into
heat but it turns it into additional charge current. The control senses both input voltage and current
and then adjust output to maximize power transfer.
Explanation
Let electric current is flowing flow through a slab of conductor or semiconductor along its length. A
magnetic field is applied to the slab perpendicular direction of the current flow along its thickness.
Due to the force of magnetic field (Lorentz force), the charge carriers are deflected towards opposite
edges of the slab. This generates electric field and develops potential difference across the edges of
the slab i.e. along the width of the slab. This electric field is perpendicular to the direction of flow of
current and magnetic field.
Charge carriers are now concentrated along the edges of the slab. Thus, an electric field created
along edges of the slab, say EH.
(c) Under the equilibrium of forces due to magnetic and electric field
Now, charge carriers are under the influence of two forces. One force due to magnetic field i.e. FL
and second due to electric field FE. Both forces are in opposite directions. Under equilibrium, if
magnitude of both forces is are equal and net force on charge carrier is zero.
Thus, 𝐹𝐿 = 𝐹𝐸
Substituting the values from (2) and (3) 𝐵𝑞𝑣𝑑 = 𝑞𝐸𝐻
Or 𝐸𝐻 = 𝐵𝑣𝑑 --- (4)
If VH is potential difference generated along the width of the slab due to the electric field EH, then,
𝑉𝐻
𝐸𝐻 = 𝑤
𝑉𝐻
Putting the value of EH in equation (4) = 𝐵𝑣𝑑
𝑤
Or 𝑉𝐻 = 𝐵𝑣𝑑 𝑤
𝐼 𝐼
As, 𝑣𝑑 = 𝑛𝑞𝑤𝑑 𝑉𝐻 = 𝐵 𝑛𝑞𝑤𝑑 𝑤
𝐵𝐼
Or 𝑉𝐻 = 𝑛𝑞𝑑 --- (5)
1 𝐵𝐼
Or 𝑉𝐻 = 𝑛𝑞 --- (6)
𝑑
1
Let the quantity = 𝑅𝐻 . This quantity is known as Hall coefficient.
𝑛𝑞
𝐵𝐼
Thus, Hall Voltage is given by 𝑉𝐻 = 𝑅𝐻 --- (7)
𝑑
Hence, magnitude and direction of Hall voltage is dependent on magnitude and direction of current
and magnetic field. Also, Hall voltage is inversely proportional to thickness of the slab.
Page 21 of 27
Applications of Hall Effect
(a) Determination of type of semiconductor
𝐵𝐼
The Hall voltage developed across the edges of the semiconductor is given by 𝑉𝐻 = 𝑅𝐻 or Hall
𝑑
𝑑
coefficient 𝑅𝐻 = 𝑉𝐻 𝐵𝐼
By measuring Hall voltage, the value of Hall coefficient RH can be determined.
If value of RH is positive then type of semiconductor is p-type. If RH is negative the type of
semiconductor is n-type.
(b) Determination of charge carrier concentration
𝑑
Hall coefficient is given by 𝑅𝐻 = 𝑉𝐻 𝐵𝐼
1
This value of Hall coefficient is also equal to 𝑅𝐻 = 𝑛𝑞
1
Hence, charge carrier concentration 𝑛=𝑅
𝐻𝑞
Thus, if value of RH is known, the charge carrier concentration can be found.
(c) Determination of charge carrier mobility
The electrical conductivity is given by 𝜎 = 𝑛𝑞𝜇
where is mobility of charge carrriers
𝜎
Thus, 𝜇 = 𝑛𝑞
1
As 𝑅𝐻 = 𝑛𝑞 𝜇 = 𝜎𝑅𝐻
Thus, the charge mobility can be determined using Hall coefficient.
3/4 Marks
1. Derive the expression for barrier potential for a PN junction.
2. Derive the ideal diode equation for a PN junction. [Dec 19, 4m]
3. Explain in brief how free electron theory explains electrical conductivity and thermal
conductivity of solids, and relation between electrical and thermal conductivity of solids
(Wiedemann–Franz law). What are the limitations of this theory?
4. Explain terms (a) valence band (b) conduction band (c) band gap energy.
5. Explain in brief concept of effective mass of electron. [Dec 19, 3m]
6. Explain in brief density of states.
7. What is Fermi level? Explain Fermi-Dirac probability distribution function specifying the
meaning of each symbol.
8. What is Fermi level? Show the position of Fermi level in P-type semiconductor at T=0K and
T>0 K
Page 22 of 27
9. Write the formula for the Fermi Dirac probability distribution function. Draw in the same
figure the Fermi Dirac probability versus electron energy at T=0 K, T1 and T2 (where T2> T1> 0
K). Explain the significance of the figure.
10. What is Fermi energy in a semiconductor? With the help of a labeled diagram, show the
position of Fermi level in case of a diode that is connected in forward bias.
11. Draw a neat and labeled diagram showing Fermi energy level in case of a P-type and N-type
semiconductor at 0K.
12. What is photovoltaic effect? Draw IV characteristics of solar cell and define fill factor.
[Dec 19, 3m]
13. State the advantages, limitations and applications of solar cell.
14. State any four measures to improve efficiency of solar cell. [Dec 19, 4m]
Numerical on: Solid State Physics
Formulae:
hc
1. Band gap energy = Eg = hν = λ
2. Conductivity of intrinsci semiconductor = σ = ne(μe + μh )
1
3. Resistivity of intrinsic semiconductor = ρ = ne(μ +μ )
e h
1 1
4. Resistivity of doped semiconductor = ρ = na eμh
or ρ = nd eμh
Avogadro number
5. number of atoms = Atomic weight
× density
6. Mobility = 𝜇 = 𝜎𝑅𝐻
𝑘𝑇 𝑁 𝑁
7. Barrier potential, 𝑉0 = ln 𝐷 2 𝐴
𝑒 𝑛𝑖
𝑒𝑉𝐹
8. Ideal diode equation, 𝐼 = 𝐼0 (𝑒 𝑘𝑇 − 1)
1 BI
9. Hall Voltage: VH =
ne d
Example: Calculate the energy gap of silicon (in eV), given that it is transparent to radiation of
wavelength greater than 11000 Å.
Solution:
hc 6.63 × 10−34 × 3 × 108 −19
1.80 × 10−19
Eg = hν = = = 1.80 × 10 J = = 𝟏. 𝟏𝟑 𝐞𝐕
λ 11000 × 10−10 1.6 × 10−19
Example: Calculate the number of acceptors to be added to a germanium sample to obtain the
resistivity of 8 -cm [Given µ=1600 cm2/volt-sec]
Solution:
Data: ρ = 8 Ω-cm, μh = 1600 cm2/V-s
1
Resistivity ρ =
na eμh
1 1
∴ 𝑛𝑎 = = = 4.876 × 1014 /cc
𝜌𝑒𝜇ℎ 8 × 1.6 × 10−19 × 1600
Page 23 of 27
Example: An N type semiconductor is to have resistivity 10 ohm-cm. Calculate the number of donor
atoms which must be added to achieve this. Given µd= 500 cm3/Vs
Solution:
Data: ρ = 10 Ω-cm, μd = 500 cm2/V-s, nd=?
1
Formula: 𝜎𝑛 = 𝑛𝑑 𝜇𝑑 𝑒 or 𝜎𝑛 = 𝜌 = 𝑛𝑑 𝜇𝑑 𝑒
𝑛
1 1
Thus, 𝑛𝑑 = = = 1.248 × 1015 /𝑐𝑐
𝜌𝑛 𝜇𝑑 𝑒 10×1.6×10−9 ×500
Example: A germanium sample has 4.56x1022 atoms/cc and a donor impurity in the ratio of one part
per 1010 is added to create an N type semiconductor. If the mobility of charge carriers is 3900 cm2/V-
s, find the conductivity of silicon.
Solution:
Data: Density of atoms in germanium = 4.56x1022 atoms/cc
Donor impurity = 1 atom/1010 Si atoms
Mobility of charge carriers = 3900 cm2/V-s
4.56×1022
Charge carrier density =n= = 4.56 × 1012 /𝑐𝑐
1010
Thus, conductivity = σ = n. e. μe = 4.56 × 1012 × 1.6 × 10−19 × 3900 = 2.849 × 10−3 mho/cm
Example: Calculate the conductivity of pure silicon at room temperature when concentration of
carriers is 1.6x1010 per cc [µe=1500 cm2/V-sec, µh=500 cm2/V-sec] [Dec 19, 4m]
Solution:
Given: µe=1500 cm2/V-sec, µh=500 cm2/V-sec, ni = 1.6x1010 /cm3
i = eni ( e + h )
Therefore the conductivity of pure silicon is given by
𝜎𝑖 = 1.6 × 10−19 × 1.6 × 1010 × ( 1500 + 500) = 5.126 × 10−6 mho/cm
Example: Calculate the conductivity of germanium sample if a donor impurity is added to the extent
of one part in 107 germanium atoms at room temperature. [Given: Atomic weight of germanium:
72.6, Density of Ge: 5.32 gm/cc, Avogadro Number: 6.022x1023 mol-1, mobility µ = 3800 cm2/V-s]
Solution:
The expression for conductivity is given by σ = n. e. μe
Page 24 of 27
4.412 × 1022
n= = 4.41 × 1013 /cc
109
The conductivity, therefore is,
σ = n. e. μe = 4.412 × 1013 × 1.6 × 10−19 × 3800 = 0.0268 mho/cm
Example: Calculate the potential barrier for a germanium PN junction at room temperature (270) if
both p and n regions are doped equally and to the extent of one atom per 106 germanium atoms.
[Given: Concentration of germanium atoms = 2.4x1019 /m3, Carrier concentration of intrinsic
germanium is 4.4x1028 atoms/m3, Boltzmann constant = 1.38x10-23 m2kg s-2 K-1]
Solution:
T = 270 = 300K
As intrinsic Germanium is doped equally with one atom per 106 Ge atoms,
4.4×1028
Concentration of donor and acceptor atoms ND=NA = = 4.4 × 1022 atoms/m3
106
Example: Current flowing in a PN junction is 0.2 A at room temperature (270) when a large reverse
bias voltage is applied. Calculate the current when a forward bias of 0.1 V is applied.
[Given: Boltzmann constant = 1.38x10-23 m2kg s-2 K-1]
Solution: I0 = 0.2 A = 2x10-7 A, V= 0.1 V, T = 270 = 300K
𝑒𝑉
𝐼 = 𝐼0 (𝑒 𝑘𝑇 − 1) = 2 × 10−7 (𝑒 0.1/0.0026 − 1) = 9.2 𝐴
Example: The Hall coefficient of a specimen of a doped silicon is found to be 3.66 x 10 -3 m3/C. The
resistivity of specimen is 8.93 m. Determine the mobility of the charge carriers.
Solution:
RH = 3.66 x 10-3 m3/C, =8.93 -m, =?
1 1
𝜎= =
𝜌 8.93
1
𝜇 = 𝜎𝑅𝐻 = 8.93 × 3.66 x 10−3 = 0.4098 × 10−3 cm2/V-s
Example: The Hall coefficient of a specimen of a doped silicon is found to be 3.66 x 103 m3/C. The
resistivity of specimen is 8.93 x 103 m. Determine the mobility of the charge carriers.
Solution:
RH = 3.66 x 103 m3/C, =8.93 x 103 -m, =?
1 1
𝜎 = 𝜌 = 8.93 x 103
1
𝜇 = 𝜎𝑅𝐻 = 8.93 x 103 × 3.66 x 103 = 0.4098 cm2/V-s
Example: Calculate the mobility of charge carriers in doped silicon whose conductivity is 100 per Ω-m
and the Hall coefficient is 3.6 x 10-4 m3/coulomb. [Dec 19, 4m]
Solution:
Given: σ=100 (Ohm-m)-1, RH = 3.6 x 10-4 m3/coulomb
m2
𝜇 = 𝜎 × R H = 100 × 3.6 × 10−4 = 3.6 × 10−2
V−S
Page 25 of 27
Example: The resistivity of doped silicon material is 0.009 Ω-m. The Hall coefficient is 3.6 x10-4
m3/coulomb. Assuming there is only one type of charge carriers, find the mobility and density of
charge carriers.
Solution:
RH 3.6 × 10−4 m2
Mobility μ = σR H = = = 0.04
ρ 0.009 V−S
1
Hall coefficient = R H = ne
1 1
Thus, n= R = 3.6 ×10−4 ×1.6×10−19 = 1.736 × 1022 electrons/cc
He
Example: A slab of silicon 2 cm in length, 1.5 cm wide and 2 mm thick is applied with magnetic field
of 0.4 T along its thickness. When a current of 75 A flows along the length, the voltage measured
across its width is 0.81 mV. Calculate the concentration of mobile electrons in silicon.
Solution:
Given: VH = 0.81 mV = 0.81x10-3 V, B = 0.4 T, I = 75 A, w = 1.5 cm = 1.5x10-2 m, d = 2 mm = 2x10-3 m
1 BI
VH =
ne d
1 BI 1 0.4×75
𝑛= = × = 1.851 × 107 electrons/m3
VH d 0.81×10−3 2×10−3
𝜇 m2
𝜎= ⟹ 𝜇 = 𝜎 × R H = 5.8 × 107 × 0.074 × 10−9 = 0.4292 × 10−2
RH V−S
Example: A specimen having length 1.00 cm, width 1.00 mm and thickness 0.1 mm is made to
conduct with 1.00 mA current and is placed in a magnetic field of 1.0 Wb/m2 acting along the
thickness. Calculate the Hall voltage in case of (i) N-type semiconductor with Hall coefficient -
-8 3 -10 3
3.44 x 10 m /C (ii) Aluminium with Hall coefficient of -0.3 x 10 m /C. Which of these materials is
more sensitive to Hall effect? Why?
Page 26 of 27
Data: d = 1 x 10-3m, Area A = (1 x 10-3m) x (0.1 x 10-3m) = 10-7 m2, I = 1 x 10-3 amp, B =1.0 Wb/m2,
i) For N-type semiconductor, RH = -3.44 x 10-8 m3/C
BId −8
1 × 1 × 10−3 × 1 × 10−3
VH = R H = −3.44 × 10 × = −3.44 × 10−7 V
A 10−7
= −𝟎. 𝟑𝟒𝟒 𝛍𝐕
____________________
Page 27 of 27