Loctite 404 Eng PDF
Loctite 404 Eng PDF
2. HAZARDS IDENTIFICATION
EMERGENCY OVERVIEW
WARNING: BONDS SKIN IN SECONDS.
COMBUSTIBLE LIQUID.
CAUSES EYE IRRITATION.
MAY CAUSE RESPIRATORY IRRITATION.
SUSPECTED OF CAUSING CANCER.
PICTOGRAM(S)
Precautionary Statements
Prevention:
Obtain special instructions before use. Do not handle until all safety precautions have been
read and understood. Keep away from heat, sparks, open flames, hot surfaces - no smoking.
Avoid breathing vapors, mist, or spray. Wash affected area thoroughly after handling. Use only
outdoors or in a well-ventilated area. Wear protective gloves, clothing, eye and face protection.
Response:
IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for
breathing. Call a POISON CENTER or physician if you feel unwell. IF IN EYES: Rinse
cautiously with water for several minutes. Remove contact lenses, if present and easy to do.
Continue rinsing. IF exposed or concerned: Get medical attention. If eye irritation persists: Get
medical attention. In case of fire: Use foam, dry chemical or carbon dioxide to extinguish.
Storage:
Store in a well-ventilated place. Keep container tightly closed. Store in a well-ventilated place.
Keep cool. Store locked up.
Disposal:
Dispose of contents and/or container according to Federal, State/Provincial and local
governmental regulations.
Classification complies with OSHA Hazard Communication Standard (29 CFR 1910.1200) and is consistent with the provisions of the
United Nations Globally Harmonized System of Classification and Labeling of Chemicals (GHS).
* Exact percentages may vary or are trade secret. Concentration range is provided to assist users in providing appropriate protections.
Skin contact: Do not pull bonded skin apart. Soak in warm soapy water. Gently peel apart
using a blunt instrument. If skin is burned due to the rapid generation of heat
by a large drop, seek medical attention. If lips are bonded, apply warm water
to the lips and encourage wetting and pressure from saliva in mouth. Peel or
roll lips apart. Do not pull lips apart with direct opposing force.
Eye contact: Immediately flush with plenty of water for at least 15 minutes. Get medical
attention. If eyelids are bonded closed, release eyelashes with warm water by
covering with a wet pad. Do not force eye open. Cyanoacrylate will bond to
eye protein and will cause a lachrymatory effect which will help to debond the
adhesive. Keep eye covered until debonding is complete, usually within 1-3
days. Medical attention should be sought in case solid particles of
polymerized cyanoacrylate trapped behind the eyelid caused abrasive
damage.
Ingestion: Ensure breathing passages are not obstructed. The product will polymerize
rapidly and bond to the mouth making it almost impossible to swallow. Saliva
will separate any solidified product in several hours. Prevent the patient from
swallowing any separated mass.
Notes to physician: Surgery is not necessary to separate accidentally bonded tissues. Experience
has shown that bonded tissues are best treated by passive, non-surgical first
aid. If rapid curing has caused thermal burns they should be treated
symptomatically after adhesive is removed.
Special firefighting procedures: Wear a self-contained breathing apparatus with a full face piece operated in
pressure-demand or other positive pressure mode.
Hazardous combustion products: Trace amounts of toxic and/or irritating fumes may be released and the use of
breathing apparatus is recommended.
Environmental precautions: Ventilate area. Do not allow product to enter sewer or waterways.
Clean-up methods: Do not use cloths for mopping up. Flood with water to complete polymerization
and scrape off the floor. Cured material can be disposed of as non-hazardous
waste. Refer to Section 8 "Exposure Controls / Personal Protection" prior to
clean up.
IDH number: 135465 Product name: LOCTITE 404 INSTANT ADHESIVE known as LOCTITE® 404™ INSTANT ADHESIVE
Page 2 of 5
7. HANDLING AND STORAGE
Handling: Prevent contact with eyes, skin and clothing. Do not breathe vapor and mist.
Wash thoroughly after handling. Avoid contact with fabric or paper goods.
Contact with these materials may cause rapid polymerization which can
generate smoke and strong irritating vapors, and cause thermal burns.
Storage: Keep in a cool, well ventilated area away from heat, sparks and open flame.
Keep container tightly closed until ready for use.
Engineering controls: Use positive down-draft exhaust ventilation if general ventilation is insufficient
to maintain vapor concentration below established exposure limits.
Respiratory protection: Use a NIOSH approved supplied air respirator with an organic cartridge if the
potential to exceed established exposure limits exists.
Eye/face protection: Safety goggles or safety glasses with side shields. Full face protection should
be used if the potential for splashing or spraying of product exists.
Skin protection: Use nitrile gloves and aprons as necessary to prevent contact. Do not use
PVC, nylon or cotton.
IDH number: 135465 Product name: LOCTITE 404 INSTANT ADHESIVE known as LOCTITE® 404™ INSTANT ADHESIVE
Page 3 of 5
10. STABILITY AND REACTIVITY
Stability: Stable under recommended storage conditions.
Hazardous reactions: Rapid exothermic polymerization will occur in the presence of water, amines, alkalis and
alcohols.
Inhalation: May cause respiratory tract irritation. Exposure to vapors above the established exposure limit
results in respiratory irritation, which may lead to difficulty in breathing and tightness in the
chest.
Skin contact: Bonds skin in seconds. May cause skin irritation. Cyanoacrylates have been reported to cause
allergic reaction but due to rapid polymerization at the skin surface, an allergic response is rare.
Cyanoacrylates generate heat on solidification. In rare circumstances a large drop will burn the
skin. Cured adhesive does not present a health hazard even if bonded to the skin.
Eye contact: Irritating to eyes. Causes excessive tearing. Eyelids may bond.
Ingestion: Not expected to be harmful by ingestion. Rapidly polymerizes (solidifies) and bonds in mouth. It
is almost impossible to swallow.
Hazardous Component(s) LD50s and LC50s Immediate and Delayed Health Effects
Ethyl 2-cyanoacrylate None Irritant, Allergen, Respiratory
Oral LD50 (Rat) = 320 mg/kg
Blood, Bone Marrow, Central nervous
Oral LD50 (Mouse) = 245 mg/kg
Hydroquinone system, Developmental, Eyes, Immune
Oral LD50 (Rabbit) = 540 mg/kg
system, Irritant, Liver, Mutagen, Skin, Thyroid
Dermal LD50 (Rat) = > 900 mg/kg
OSHA Carcinogen
Hazardous Component(s) NTP Carcinogen IARC Carcinogen
(Specifically Regulated)
Ethyl 2-cyanoacrylate No No No
Hydroquinone No No No
Recommended method of disposal: Follow all local, state, federal and provincial regulations for disposal.
IDH number: 135465 Product name: LOCTITE 404 INSTANT ADHESIVE known as LOCTITE® 404™ INSTANT ADHESIVE
Page 4 of 5
International Air Transportation (ICAO/IATA)
Proper shipping name: Aviation regulated liquid, n.o.s. (Cyanoacrylate ester)
Hazard class or division: 9
Identification number: UN 3334
Packing group: III
Exceptions: (Not more than 500ml) Unrestricted
TSCA 8 (b) Inventory Status: All components are listed as active or are exempt from listing on the Toxic Substances
Control Act (TSCA) inventory.
TSCA 12 (b) Export Notification: None above reporting de minimis
California Proposition 65: No California Proposition 65 listed chemicals are known to be present.
CEPA DSL/NDSL Status: All components are listed on or are exempt from listing on the Canadian Domestic
Substances List.
DISCLAIMER: The data contained herein are furnished for information only and are believed to be reliable. However, Henkel
Corporation and its affiliates (“Henkel”) does not assume responsibility for any results obtained by persons over whose methods
Henkel has no control. It is the user’s responsibility to determine the suitability of Henkel’s products or any production methods
mentioned herein for a particular purpose, and to adopt such precautions as may be advisable for the protection of property and
persons against any hazards that may be involved in the handling and use of any Henkel’s products. In light of the foregoing,
Henkel specifically disclaims all warranties, express or implied, including warranties of merchantability and fitness for a particular
purpose, arising from sale or use of Henkel’s products. Henkel further disclaims any liability for consequential or incidental damages
of any kind, including lost profits.
This Safety Data Sheet has been generated based on OSHA Hazard Communication Standard (29 CFR 1910.1200) and provides
information in accordance with U.S. federal law only. No warranty or representation of any kind is given with respect to the
substantive or export laws of any other jurisdiction or country. Please confirm that the information provided herein conforms to the
substantive export or other law of any other jurisdiction prior to export. Please contact Henkel Product Safety and Regulatory
Affairs for additional assistance.
IDH number: 135465 Product name: LOCTITE 404 INSTANT ADHESIVE known as LOCTITE® 404™ INSTANT ADHESIVE
Page 5 of 5
Safety Data Sheet
2. HAZARDS IDENTIFICATION
EMERGENCY OVERVIEW
WARNING: BONDS SKIN IN SECONDS.
COMBUSTIBLE LIQUID.
CAUSES EYE IRRITATION.
MAY CAUSE RESPIRATORY IRRITATION.
PICTOGRAM(S)
Precautionary Statements
Prevention:
Keep aw ay from heat, sparks, open flames, hot surfaces - no smoking. Avoid breathing vapors,
mist, or spray. Wash affected area thoroughly after handling. Use only outdoors or in a w ell-
ventilated area. Wear protective gloves, eye protection, and face protection.
Response:
IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for
breathing. Call a POISON CENTER or physician if you feel unw ell. IF IN EYES: Rinse
cautiously w ith water for several minutes. Remove contact lenses, if present and easy to do.
Continue rinsing. If eye irritation persists: Get medical attention. In case of fire: Use foam, dry
chemical or carbon dioxide to extinguish.
Storage:
Store in a w ell-ventilated place. Keep container tightly closed. Store in a w ell-ventilated place.
Keep cool. Store locked up.
Disposal:
Dispose of contents and/or container according to Federal, State/Provincial and local
governmental regulations.
Classification complies w ith OSHA Hazard Communication Standard (29 CFR 1910.1200) and is consistent with the provisions of t he
United Nations Globally Harmonized System of Classification and Labeling of Chemicals (GHS).
* Exact percentages may vary or are trade secret. Concentration range is provided to assist users in providing appropriate pr otections.
Skin contact: Do not pull bonded skin apart. Soak in w arm soapy water. Gently peel apart
using a blunt instrument. If skin is burned due to the rapid generation of heat
by a large drop, seek medical attention. If lips are bonded, apply w arm water
to the lips and encourage w etting and pressure from saliva in mouth. Peel or
roll lips apart. Do not pull lips apart w ith direct opposing force.
Eye contact: Immediately flush w ith plenty of w ater for at least 15 minutes. Get medical
attention. If eyelids are bonded closed, release eyelashes with warm water by
covering w ith a w et pad. Do not force eye open. Cyanoacrylate will bond to
eye protein and w ill cause a lachrymatory effect which will help to debond the
adhesive. Keep eye covered until debonding is complete, usually w ithin 1-3
days. Medical attention should be sought in case solid particles of
polymerized cyanoacrylate trapped behind the eyelid caused abrasive
damage.
Ingestion: Ensure breathing passages are not obstructed. The product w ill polymerize
rapidly and bond to the mouth making it almost impossible to sw allow. Saliva
w ill separate any solidified product in several hours. Prevent the patient from
sw allowing any separated mass.
Notes to physician: Surgery is not necessary to separate accidentally bonded tissues. Experience
has show n that bonded tissues are best treated by passive, non-surgical first
aid. If rapid curing has caused thermal bums they should be treated
symptomatically after adhesive is removed.
Special firefighting procedures: Wear a self-contained breathing apparatus with a full face piece operated in
pressure-demand or other positive pressure mode.
Hazardous combustion products: Trace amounts of toxic and/or irritating fumes may be released and the use of
breathing apparatus is recommended.
Environm ental precautions: Ventilate area. Do not allow product to enter sew er or waterways.
Clean-up methods: Do not use cloths for mopping up. Flood w ith w ater to complete polymerization
and scrape off the floor. Cured material can be disposed of as non-hazardous
w aste. Refer to Section 8 "Exposure Controls / Personal Protection" prior to
clean up.
Engineering controls: Use positive dow n-draft exhaust ventilation if general ventilation is insufficient
to maintain vapor concentration below established exposure limits.
Respiratory protection: Use NIOSH approved respirator if there is potential to exceed exposure
limit(s). Use NIOSH approved respirator if there is potential to exceed
exposure limit(s).
Eye/face protection: Safety goggles or safety glasses with side shields. Full face protection should
be used if the potential for splashing or spraying of product exists. Safety
goggles or safety glasses with side shields. Full face protection should be
used if the potential for splashing or spraying of product exists.
Skin protection: Use nitrile gloves and aprons as necessary to prevent contact. Do not use
PVC, nylon or cotton. Use nitrile gloves and aprons as necessary to prevent
contact. Do not use PVC, nylon or cotton.
Hazardous reactions: Rapid exothermic polymerization w ill occur in the presence of water, amines, alkalis and
alcohols.
Inhalation: May cause respiratory tract irritation. Exposure to vapors above the established exposure limit
results in respiratory irritation, w hich may lead to difficulty in breathing and tightness in the
chest.
Skin contact: May cause skin irritation. Bonds skin in seconds. Cyanoacrylates have been reported to cause
allergic reaction but due to rapid polymerization at the skin surface, an allergic response is rare.
Cyanoacrylates generate heat on solidification. In rare circumstances a large drop w ill burn the
skin. Cured adhesive does not present a health hazard even if bonded to the skin.
Eye contact: Irritating to eyes. Causes excessive tearing. Eyelids may bond.
Ingestion: Not expected to be harmful by ingestion. Rapidly polymerizes (solidifies) and bonds in mouth. It
is almost impossible to sw allow.
Hazardous Component(s) LD50s and LC50s Im m ediate and Delayed Health Effects
Ethyl 2-cyanoacrylate None Irritant, Allergen, Respiratory
Siloxanes and Silicones, di-Me, reaction
None No Data
products w ith silica
OSHA Carcinogen
Hazardous Component(s) NTP Carcinogen IARC Carcinogen
(Specifically Regulated)
Ethyl 2-cyanoacrylate No No No
Siloxanes and Silicones, di-Me, reaction
No No No
products w ith silica
Recom mended method of disposal: Follow all local, state, federal and provincial regulations for disposal.
TSCA 8 (b) Inventory Status: All components are listed as active or are exempt from listing on the Toxic Substances
Control Act (TSCA) inventory.
California Proposition 65: This product contains a chemical know n to the State of California to cause birth defects or
other reproductive harm.
CEPA DSL/NDSL Status: Contains one or more components listed on the Non-Domestic Substances List. All other
components are listed on or are exempt from listing on the Domestic Substances List.
Components listed on the NDSL must be tracked by all Canadian Importers of Record as
required by Environment Canada. They may be imported into Canada in limited quantities.
Please contact Regulatory Affairs for additional details.
DISCLAIMER: The data contained herein are furnished for information only and are believed to be reliable. How ever, Henkel
Corporation and its affiliates (“Henkel”) does not assume responsibility for any results obtained by persons over whose methods
Henkel has no control. It is the user’s responsibility to determine the suitability of Henkel’s products or any production methods
mentioned herein for a particular purpose, and to adopt such precautions as may be advisable for the protection of property a nd
persons against any hazards that may be involved in the handling and use of any Henkel’s products. In light of the foregoing,
Henkel specifically disclaims all w arranties, express or implied, including w arranties of merchantability and fitness for a particular
purpose, arising from sale or use of Henkel’s products. Henkel further disclaims any liability for consequential or incidental damages
of any kind, including lost profits.
This Safety Data Sheet has been generated based on OSHA Hazard Communication Standard (29 CFR 1910.1200) and provides
information in accordance with U.S. federal law only. No w arranty or representation of any kind is given w ith respect to the
substantive or export law s of any other jurisdiction or country. Please confirm that the information provided herein conforms to the
substantive export or other law of any other jurisdiction prior to export. Please contact Henkel Product Safety and Regulatory
Affairs for additional assistance.
2. HAZARDS IDENTIFICATION
EMERGENCY OVERVIEW
WARNING: CAUSES SKIN IRRITATION.
MAY CAUSE AN ALLERGIC SKIN REACTION.
CAUSES SERIOUS EYE IRRITATION.
MAY CAUSE DAMAGE TO ORGANS THROUGH PROLONGED OR
REPEATED EXPOSURE.
PICTOGRAM(S)
Precautionary Statements
Prevention: Do not breathe vapors, mist, or spray. Wash affected area thoroughly after handling.
Contaminated work clothing should not be allowed out of the workplace. Wear protective
gloves, eye protection, and face protection.
Response: IF ON SKIN: Wash with plenty of water. IF IN EYES: Rinse cautiously with water for several
minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Get medical
attention if you feel unwell. If skin irritation or rash occurs: Get medical attention. If eye irritation
persists: Get medical attention. Take off contaminated clothing.
Storage: Not prescribed
Disposal: Dispose of contents and/or container according to Federal, State/Provincial and local
governmental regulations.
Classification complies with OSHA Hazard Communication Standard (29 CFR 1910.1200) and is consistent with the provisions of the
United Nations Globally Harmonized System of Classification and Labeling of Chemicals (GHS).
* Exact percentages may vary or are trade secret. Concentration range is provided to assist users in providing appropriate protections.
Skin contact: Immediately flush skin with plenty of water (using soap, if available). Remove
contaminated clothing and footwear. Wash clothing before reuse. Get medical
attention.
Eye contact: Rinse immediately with plenty of water, also under the eyelids, for at least 15
minutes. Get medical attention.
Special firefighting procedures: Wear self-contained breathing apparatus and full protective clothing, such as
turn-out gear. In case of fire, keep containers cool with water spray.
Unusual fire or explosion hazards: Uncontrolled polymerization may occur at high temperatures resulting in
explosions or rupture of storage containers.
Clean-up methods: Remove all sources of ignition. Evacuate and ventilate spill area; dike spill to
prevent entry into water system; wear full protective equipment during clean-
up. Soak up with inert absorbent material (e.g. sand, silica gel, acid binder,
universal binder, sawdust). Scrape up as much material as possible. Store in a
partly filled, closed container until disposal. Refer to Section 8 "Exposure
Controls / Personal Protection" prior to clean up.
IDH number: 233546 Product name: Retaining Compound 641 Medium Strength
Page 2 of 5
8. EXPOSURE CONTROLS / PERSONAL PROTECTION
Employers should complete an assessment of all workplaces to determine the need for, and selection of, proper
exposure controls and protective equipment for each task performed.
Engineering controls: Provide adequate local exhaust ventilation to maintain worker exposure below
exposure limits.
Respiratory protection: Use NIOSH approved respirator if there is potential to exceed exposure
limit(s).
Eye/face protection: Safety goggles or safety glasses with side shields. Full face protection should
be used if the potential for splashing or spraying of product exists. Safety
showers and eye wash stations should be available.
Skin protection: Use chemical resistant, impermeable clothing including gloves and either an
apron or body suit to prevent skin contact. Neoprene gloves.
Hazardous reactions: None under normal processing. Polymerization may occur at elevated temperature or in the
presence of incompatible materials.
Incompatible materials: Free radical initiators. Oxidizing agents. Reducing agents. Metal oxides. Acids. Alkalis.
Conditions to avoid: Elevated temperatures. Heat, flames, sparks and other sources of ignition. Store away from
incompatible materials.
IDH number: 233546 Product name: Retaining Compound 641 Medium Strength
Page 3 of 5
11. TOXICOLOGICAL INFORMATION
Relevant routes of exposure: Skin, Inhalation, Eyes, Ingestion
Inhalation: Inhalation of vapors or mists of the product may be irritating to the respiratory system. May
cause irritation to nose and throat.
Skin contact: Causes skin irritation. May cause allergic skin reaction.
Eye contact: Causes serious eye irritation.
Ingestion: May cause irritation to the gastrointestinal tract, mouth and mucous membranes.
Hazardous Component(s) LD50s and LC50s Immediate and Delayed Health Effects
Polyglycol dioctanoate None Irritant
Allergen, Central nervous system, Corrosive,
Cumene hydroperoxide None
Irritant, Mutagen
Saccharin Oral LD50 (Mouse) = 17 g/kg No Target Organs
Oral LD50 (Rat) = 7,800 mg/kg
Allergen, Irritant, Kidney, Liver, Mutagen,
Methyl methacrylate Oral LD50 (Rabbit) = 6,000 mg/kg
Nervous System, Respiratory
Oral LD50 (Rat) = 9,400 mg/kg
OSHA Carcinogen
Hazardous Component(s) NTP Carcinogen IARC Carcinogen
(Specifically Regulated)
Polyglycol dioctanoate No No No
Cumene hydroperoxide No No No
Saccharin No No No
Methyl methacrylate No No No
Recommended method of disposal: Follow all local, state, federal and provincial regulations for disposal.
IDH number: 233546 Product name: Retaining Compound 641 Medium Strength
Page 4 of 5
15. REGULATORY INFORMATION
United States Regulatory Information
TSCA 8 (b) Inventory Status: All components are listed as active or are exempt from listing on the Toxic Substances
Control Act (TSCA) inventory.
TSCA 12 (b) Export Notification: None above reporting de minimis
California Proposition 65: This product contains a chemical known in the State of California to cause cancer. This
product contains a chemical known to the State of California to cause birth defects or other
reproductive harm.
CEPA DSL/NDSL Status: All components are listed on or are exempt from listing on the Canadian Domestic
Substances List.
DISCLAIMER: The data contained herein are furnished for information only and are believed to be reliable. However, Henkel
Corporation and its affiliates (“Henkel”) does not assume responsibility for any results obtained by persons over whose methods
Henkel has no control. It is the user’s responsibility to determine the suitability of Henkel’s products or any production methods
mentioned herein for a particular purpose, and to adopt such precautions as may be advisable for the protection of property and
persons against any hazards that may be involved in the handling and use of any Henkel’s products. In light of the foregoing,
Henkel specifically disclaims all warranties, express or implied, including warranties of merchantability and fitness for a particular
purpose, arising from sale or use of Henkel’s products. Henkel further disclaims any liability for consequential or incidental damages
of any kind, including lost profits.
This Safety Data Sheet has been generated based on OSHA Hazard Communication Standard (29 CFR 1910.1200) and provides
information in accordance with U.S. federal law only. No warranty or representation of any kind is given with respect to the
substantive or export laws of any other jurisdiction or country. Please confirm that the information provided herein conforms to the
substantive export or other law of any other jurisdiction prior to export. Please contact Henkel Product Safety and Regulatory
Affairs for additional assistance.
IDH number: 233546 Product name: Retaining Compound 641 Medium Strength
Page 5 of 5
Safety Data Sheet
2. HAZARDS IDENTIFICATION
EMERGENCY OVERVIEW
WARNING: BONDS SKIN IN SECONDS.
COMBUSTIBLE LIQUID.
CAUSES EYE IRRITATION.
MAY CAUSE RESPIRATORY IRRITATION.
PICTOGRAM(S)
Precautionary Statements
Prevention:
Keep away from heat, sparks, open flames, hot surfaces - no smoking. Avoid breathing vapors,
mist, or spray. Wash affected area thoroughly after handling. Use only outdoors or in a well-
ventilated area. Wear protective gloves, eye protection, and face protection.
Response:
IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for
breathing. Call a POISON CENTER or physician if you feel unwell. IF IN EYES: Rinse
cautiously with water for several minutes. Remove contact lenses, if present and easy to do.
Continue rinsing. If eye irritation persists: Get medical attention. In case of fire: Use foam, dry
chemical or carbon dioxide to extinguish.
Storage:
Store in a well-ventilated place. Keep container tightly closed. Store in a well-ventilated place.
Keep cool. Store locked up.
Disposal:
Dispose of contents and/or container according to Federal, State/Provincial and local
governmental regulations.
Classification complies with OSHA Hazard Communication Standard (29 CFR 1910.1200) and is consistent with the provisions of the
United Nations Globally Harmonized System of Classification and Labeling of Chemicals (GHS).
IDH number: 680522 Product name: LOCTITE 454 INSTANT ADHESIVE GEL known as LOCTITE® QUICKTITE®
INSTANT AD
Page 1 of 5
3. COMPOSITION / INFORMATION ON INGREDIENTS
Hazardous Component(s) CAS Number Percentage*
Ethyl 2-cyanoacrylate 7085-85-0 80 - 100
Siloxanes and Silicones, di-Me, reaction
67762-90-7 5 - 10
products with silica
* Exact percentages may vary or are trade secret. Concentration range is provided to assist users in providing appropriate protections.
Skin contact: Do not pull bonded skin apart. Soak in warm soapy water. Gently peel apart
using a blunt instrument. If skin is burned due to the rapid generation of heat
by a large drop, seek medical attention. If lips are bonded, apply warm water
to the lips and encourage wetting and pressure from saliva in mouth. Peel or
roll lips apart. Do not pull lips apart with direct opposing force.
Eye contact: Immediately flush with plenty of water for at least 15 minutes. Get medical
attention. If eyelids are bonded closed, release eyelashes with warm water by
covering with a wet pad. Do not force eye open. Cyanoacrylate will bond to
eye protein and will cause a lachrymatory effect which will help to debond the
adhesive. Keep eye covered until debonding is complete, usually within 1-3
days. Medical attention should be sought in case solid particles of
polymerized cyanoacrylate trapped behind the eyelid caused abrasive
damage.
Ingestion: Ensure breathing passages are not obstructed. The product will polymerize
rapidly and bond to the mouth making it almost impossible to swallow. Saliva
will separate any solidified product in several hours. Prevent the patient from
swallowing any separated mass.
Notes to physician: Surgery is not necessary to separate accidentally bonded tissues. Experience
has shown that bonded tissues are best treated by passive, non-surgical first
aid. If rapid curing has caused thermal bums they should be treated
symptomatically after adhesive is removed.
Special firefighting procedures: Wear a self-contained breathing apparatus with a full face piece operated in
pressure-demand or other positive pressure mode.
Hazardous combustion products: Trace amounts of toxic and/or irritating fumes may be released and the use of
breathing apparatus is recommended.
Environmental precautions: Ventilate area. Do not allow product to enter sewer or waterways.
Clean-up methods: Do not use cloths for mopping up. Flood with water to complete polymerization
and scrape off the floor. Cured material can be disposed of as non-hazardous
waste. Refer to Section 8 "Exposure Controls / Personal Protection" prior to
clean up.
IDH number: 680522 Product name: LOCTITE 454 INSTANT ADHESIVE GEL known as LOCTITE® QUICKTITE®
INSTANT AD
Page 2 of 5
7. HANDLING AND STORAGE
Handling: Prevent contact with eyes, skin and clothing. Do not breathe vapor and mist.
Wash thoroughly after handling. Avoid contact with fabric or paper goods.
Contact with these materials may cause rapid polymerization which can
generate smoke and strong irritating vapors, and cause thermal burns.
Engineering controls: Use positive down-draft exhaust ventilation if general ventilation is insufficient
to maintain vapor concentration below established exposure limits.
Respiratory protection: Use NIOSH approved respirator if there is potential to exceed exposure
limit(s). Use NIOSH approved respirator if there is potential to exceed
exposure limit(s).
Eye/face protection: Safety goggles or safety glasses with side shields. Full face protection should
be used if the potential for splashing or spraying of product exists. Safety
goggles or safety glasses with side shields. Full face protection should be
used if the potential for splashing or spraying of product exists.
Skin protection: Use nitrile gloves and aprons as necessary to prevent contact. Do not use
PVC, nylon or cotton. Use nitrile gloves and aprons as necessary to prevent
contact. Do not use PVC, nylon or cotton.
IDH number: 680522 Product name: LOCTITE 454 INSTANT ADHESIVE GEL known as LOCTITE® QUICKTITE®
INSTANT AD
Page 3 of 5
10. STABILITY AND REACTIVITY
Stability: Stable under recommended storage conditions.
Hazardous reactions: Rapid exothermic polymerization will occur in the presence of water, amines, alkalis and
alcohols.
Inhalation: May cause respiratory tract irritation. Exposure to vapors above the established exposure limit
results in respiratory irritation, which may lead to difficulty in breathing and tightness in the
chest.
Skin contact: May cause skin irritation. Bonds skin in seconds. Cyanoacrylates have been reported to cause
allergic reaction but due to rapid polymerization at the skin surface, an allergic response is rare.
Cyanoacrylates generate heat on solidification. In rare circumstances a large drop will burn the
skin. Cured adhesive does not present a health hazard even if bonded to the skin.
Eye contact: Irritating to eyes. Causes excessive tearing. Eyelids may bond.
Ingestion: Not expected to be harmful by ingestion. Rapidly polymerizes (solidifies) and bonds in mouth. It
is almost impossible to swallow.
Hazardous Component(s) LD50s and LC50s Immediate and Delayed Health Effects
Ethyl 2-cyanoacrylate None Irritant, Allergen, Respiratory
Siloxanes and Silicones, di-Me, reaction
None No Data
products with silica
OSHA Carcinogen
Hazardous Component(s) NTP Carcinogen IARC Carcinogen
(Specifically Regulated)
Ethyl 2-cyanoacrylate No No No
Siloxanes and Silicones, di-Me, reaction
No No No
products with silica
Recommended method of disposal: Follow all local, state, federal and provincial regulations for disposal.
IDH number: 680522 Product name: LOCTITE 454 INSTANT ADHESIVE GEL known as LOCTITE® QUICKTITE®
INSTANT AD
Page 4 of 5
International Air Transportation (ICAO/IATA)
Proper shipping name: Aviation regulated liquid, n.o.s. (Cyanoacrylate ester)
Hazard class or division: 9
Identification number: UN 3334
Packing group: III
Exceptions: Primary packs containing less than 500ml are unregulated by this mode of
transport and may be shipped unrestricted.
TSCA 8 (b) Inventory Status: All components are listed as active or are exempt from listing on the Toxic Substances
Control Act (TSCA) inventory.
California Proposition 65: This product contains a chemical known to the State of California to cause birth defects or
other reproductive harm.
CEPA DSL/NDSL Status: Contains one or more components listed on the Non-Domestic Substances List. All other
components are listed on or are exempt from listing on the Domestic Substances List.
Components listed on the NDSL must be tracked by all Canadian Importers of Record as
required by Environment Canada. They may be imported into Canada in limited quantities.
Please contact Regulatory Affairs for additional details.
DISCLAIMER: The data contained herein are furnished for information only and are believed to be reliable. However, Henkel
Corporation and its affiliates (“Henkel”) does not assume responsibility for any results obtained by persons over whose methods
Henkel has no control. It is the user’s responsibility to determine the suitability of Henkel’s products or any production methods
mentioned herein for a particular purpose, and to adopt such precautions as may be advisable for the protection of property and
persons against any hazards that may be involved in the handling and use of any Henkel’s products. In light of the foregoing,
Henkel specifically disclaims all warranties, express or implied, including warranties of merchantability and fitness for a particular
purpose, arising from sale or use of Henkel’s products. Henkel further disclaims any liability for consequential or incidental damages
of any kind, including lost profits.
This Safety Data Sheet has been generated based on OSHA Hazard Communication Standard (29 CFR 1910.1200) and provides
information in accordance with U.S. federal law only. No warranty or representation of any kind is given with respect to the
substantive or export laws of any other jurisdiction or country. Please confirm that the information provided herein conforms to the
substantive export or other law of any other jurisdiction prior to export. Please contact Henkel Product Safety and Regulatory
Affairs for additional assistance.
IDH number: 680522 Product name: LOCTITE 454 INSTANT ADHESIVE GEL known as LOCTITE® QUICKTITE®
INSTANT AD
Page 5 of 5
Safety Data Sheet
2. HAZARDS IDENTIFICATION
EMERGENCY OVERVIEW
WARNING: CAUSES SKIN IRRITATION.
CAUSES SERIOUS EYE IRRITATION.
MAY CAUSE DAMAGE TO ORGANS THROUGH PROLONGED OR
REPEATED EXPOSURE.
PICTOGRAM(S)
Precautionary Statements
Prevention: Do not breathe dust or fumes. Wash affected area thoroughly after handling. Wear protective
gloves, eye protection, and face protection.
Response: IF ON SKIN: Wash with plenty of water. IF IN EYES: Rinse cautiously with water for several
minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Get medical
attention if you feel unwell. If skin irritation occurs: Get medical attention. If eye irritation
persists: Get medical attention. Take off contaminated clothing.
Storage: Not prescribed
Disposal: Dispose of contents and/or container according to Federal, State/Provincial and local
governmental regulations.
Classification complies with OSHA Hazard Communication Standard (29 CFR 1910.1200) and is consistent with the provisions of the
United Nations Globally Harmonized System of Classification and Labeling of Chemicals (GHS).
* Exact percentages may vary or are trade secret. Concentration range is provided to assist users in providing appropriate protections.
Skin contact: Immediately flush skin with plenty of water (using soap, if available). Remove
contaminated clothing and footwear. Wash clothing before reuse. Get medical
attention.
Eye contact: Rinse immediately with plenty of water, also under the eyelids, for at least 15
minutes. Get medical attention.
Special firefighting procedures: Wear self-contained breathing apparatus and full protective clothing, such as
turn-out gear. In case of fire, keep containers cool with water spray.
Unusual fire or explosion hazards: Uncontrolled polymerization may occur at high temperatures resulting in
explosions or rupture of storage containers.
Hazardous combustion products: Irritating organic vapours. Oxides of carbon. Toxic fluorine compounds.
Clean-up methods: Remove all sources of ignition. Evacuate and ventilate spill area; dike spill to
prevent entry into water system; wear full protective equipment during clean-
up. Soak up with inert absorbent material (e.g. sand, silica gel, acid binder,
universal binder, sawdust). Scrape up as much material as possible. Store in a
partly filled, closed container until disposal. Refer to Section 8 "Exposure
Controls / Personal Protection" prior to clean up.
IDH number: 463973 Product name: LOCTITE® Quickstix™ 561™ PST® Pipe Sealant with PTFE
Page 2 of 6
8. EXPOSURE CONTROLS / PERSONAL PROTECTION
Employers should complete an assessment of all workplaces to determine the need for, and selection of, proper
exposure controls and protective equipment for each task performed.
Engineering controls: Provide adequate local exhaust ventilation to maintain worker exposure below
exposure limits.
Respiratory protection: Use NIOSH approved respirator if there is potential to exceed exposure
limit(s).
Eye/face protection: Safety goggles or safety glasses with side shields. Full face protection should
be used if the potential for splashing or spraying of product exists. Safety
showers and eye wash stations should be available.
Skin protection: Use chemical resistant, impermeable clothing including gloves and either an
apron or body suit to prevent skin contact. Neoprene gloves.
IDH number: 463973 Product name: LOCTITE® Quickstix™ 561™ PST® Pipe Sealant with PTFE
Page 3 of 6
9. PHYSICAL AND CHEMICAL PROPERTIES
Physical state: Wax
Color: White
Odor: Mild
Odor threshold: Not available.
pH: Not applicable, Product is non-polar/aprotic.
Vapor pressure: < 10 mm hg (27 °C (80.6 °F)) < 13 mbar (25 °C (77°F)) < 0.13 mbar (20 °C
(68°F))
Boiling point/range: > 149 °C (> 300.2 °F)> 150 °C (> 302°F)
Melting point/ range: > 80 °C (> 176°F)
Specific gravity: 1.1394
Vapor density: Not applicable, Product is a solid.
Flash point: Not applicable
Flammable/Explosive limits - lower: Not available.
Flammable/Explosive limits - upper: Not available.
Autoignition temperature: Not available.
Flammability: Not applicable
Evaporation rate: Not available.
Solubility in water: Slight
Partition coefficient (n-octanol/water): Not available.
VOC content: 1.06 %; 12.06 g/l
Viscosity: Not available.
Decomposition temperature: Not available.
Hazardous reactions: None under normal processing. Polymerization may occur at elevated temperature or in the
presence of incompatible materials.
Hazardous decomposition Oxides of carbon. Toxic fluorine compounds. Irritating organic vapours.
products:
Conditions to avoid: Elevated temperatures. Heat, flames, sparks and other sources of ignition. Store away from
incompatible materials.
IDH number: 463973 Product name: LOCTITE® Quickstix™ 561™ PST® Pipe Sealant with PTFE
Page 4 of 6
Potential Health Effects/Symptoms
Inhalation: Inhalation of vapors or mists of the product may be irritating to the respiratory system.
Skin contact: Causes skin irritation. May cause allergic skin reaction.
Eye contact: Causes serious eye irritation.
Ingestion: May cause gastrointestinal tract irritation if swallowed.
Hazardous Component(s) LD50s and LC50s Immediate and Delayed Health Effects
Polyglycol dioctanoate None Irritant
Ethene, tetrafluoro-, homopolymer None No Target Organs
Silica, amorphous, fumed, crystal-free None Nuisance dust
Oral LD50 (Rat) = 5.89 g/kg Blood, Bone Marrow, Central nervous
Ethylene glycol Oral LD50 (Mouse) = 14.6 g/kg system, Developmental, Eyes, Irritant,
Dermal LD50 (Rabbit) = 9,530 mg/kg Kidney, Liver, Metabolic
Ethene, homopolymer None No Target Organs
Inhalation LC50 (Rat, 4 h) = > 6.82 mg/l
Irritant, Respiratory, Some evidence of
Titanium dioxide Inhalation LC50 (Rat, 4 h) = > 2.28 mg/l
carcinogenicity
Inhalation LC50 (Rat, 4 h) = > 3.56 mg/l
Saccharin Oral LD50 (Mouse) = 17 g/kg No Target Organs
Allergen, Central nervous system, Corrosive,
Cumene hydroperoxide None
Irritant, Mutagen
OSHA Carcinogen
Hazardous Component(s) NTP Carcinogen IARC Carcinogen
(Specifically Regulated)
Polyglycol dioctanoate No No No
Ethene, tetrafluoro-, homopolymer No No No
Silica, amorphous, fumed, crystal-free No No No
Ethylene glycol No No No
Ethene, homopolymer No No No
Titanium dioxide No Group 2B No
Saccharin No No No
Cumene hydroperoxide No No No
Recommended method of disposal: Follow all local, state, federal and provincial regulations for disposal.
IDH number: 463973 Product name: LOCTITE® Quickstix™ 561™ PST® Pipe Sealant with PTFE
Page 5 of 6
15. REGULATORY INFORMATION
United States Regulatory Information
TSCA 8 (b) Inventory Status: All components are listed as active or are exempt from listing on the Toxic Substances
Control Act (TSCA) inventory.
TSCA 12 (b) Export Notification: None above reporting de minimisNone above reporting de minimis
California Proposition 65: This product contains a chemical known in the State of California to cause cancer. This
product contains a chemical known to the State of California to cause birth defects or other
reproductive harm.
CEPA DSL/NDSL Status: All components are listed on or are exempt from listing on the Canadian Domestic
Substances List.
DISCLAIMER: The data contained herein are furnished for information only and are believed to be reliable. However, Henkel
Corporation and its affiliates (“Henkel”) does not assume responsibility for any results obtained by persons over whose methods
Henkel has no control. It is the user’s responsibility to determine the suitability of Henkel’s products or any production methods
mentioned herein for a particular purpose, and to adopt such precautions as may be advisable for the protection of property and
persons against any hazards that may be involved in the handling and use of any Henkel’s products. In light of the foregoing,
Henkel specifically disclaims all warranties, express or implied, including warranties of merchantability and fitness for a particular
purpose, arising from sale or use of Henkel’s products. Henkel further disclaims any liability for consequential or incidental damages
of any kind, including lost profits.
This Safety Data Sheet has been generated based on OSHA Hazard Communication Standard (29 CFR 1910.1200) and provides
information in accordance with U.S. federal law only. No warranty or representation of any kind is given with respect to the
substantive or export laws of any other jurisdiction or country. Please confirm that the information provided herein conforms to the
substantive export or other law of any other jurisdiction prior to export. Please contact Henkel Product Safety and Regulatory
Affairs for additional assistance.
IDH number: 463973 Product name: LOCTITE® Quickstix™ 561™ PST® Pipe Sealant with PTFE
Page 6 of 6
Safety Data Sheet
2. HAZARDS IDENTIFICATION
EMERGENCY OVERVIEW
WARNING: CAUSES SKIN IRRITATION.
MAY CAUSE AN ALLERGIC SKIN REACTION.
CAUSES SERIOUS EYE IRRITATION.
MAY CAUSE DAMAGE TO ORGANS THROUGH PROLONGED OR
REPEATED EXPOSURE.
PICTOGRAM(S)
Precautionary Statements
Prevention: Do not breathe vapors, mist, or spray. Wash affected area thoroughly after handling.
Contaminated w ork clothing should not be allow ed out of the w orkplace. Wear protective
gloves, eye protection, and face protection.
Response: IF ON SKIN: Wash w ith plenty of water. IF IN EYES: Rinse cautiously w ith water for several
minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Get medical
attention if you feel unw ell. If skin irritation or rash occurs: Get medical attention. If eye irritation
persists: Get medical attention. Take off contaminated clothing.
Storage: Not prescribed
Disposal: Dispose of contents and/or container according to Federal, State/Prov incial and local
governmental regulations.
Classification complies w ith OSHA Hazard Communication Standard (29 CFR 1910.1200) and is consistent with the provisions of t he
United Nations Globally Harmonized System of Classification and Labeling of Chemicals (GHS).
* Exact percentages may vary or are trade secret. Concentration range is provided to assist users in providing appropriate pr otections.
Skin contact: Immediately flush skin w ith plenty of w ater (using soap, if available). Remove
contaminated clothing and footwear. Wash clothing before reuse. Get medical
attention.
Eye contact: Rinse immediately w ith plenty of w ater, also under the eyelids, for at least 15
minutes. Get medical attention.
Special firefighting procedures: Wear self-contained breathing apparatus and full protective clothing, such as
turn-out gear. In case of fire, keep containers cool w ith w ater spray.
Unusual fire or explosion hazards: Uncontrolled polymerization may occur at high temperatures resulting in
explosions or rupture of storage containers.
Hazardous combustion products: Oxides of carbon. Oxides of sulfur. Oxides of nitrogen. Irritating organic
vapours.
Clean-up methods: Remove all sources of ignition. Evacuate and ventilate spill area; dike spill to
prevent entry into w ater system; w ear full protective equipment during clean-
up. Soak up w ith inert absorbent material (e.g. sand, silica gel, acid binder,
universal binder, saw dust). Scrape up as much material as possible. Store in a
partly filled, closed container until disposal. Refer to Section 8 "Exposure
Controls / Personal Protection" prior to clean up.
Engineering controls: Provide adequate local exhaust ventilation to maintain w orker exposure below
exposure limits.
Respiratory protection: Use NIOSH approved respirator if there is potential to exceed exposure
limit(s).
Eye/face protection: Safety goggles or safety glasses with side shields. Full face protection should
be used if the potential for splashing or spraying of product exists. Safety
show ers and eye wash stations should be available.
Skin protection: Use chemical resistant, impermeable clothing including gloves and either an
apron or body suit to prevent skin contact. Neoprene gloves.
Hazardous reactions: None under normal processing. Polymerization may occur at elevated temperature or in the
presence of incompatible materials.
Hazardous decomposition Oxides of carbon. Oxides of sulfur. Oxides of nitrogen. Irritating organic vapours.
products:
Conditions to avoid: Elevated temperatures. Heat, flames, sparks and other sources of ignition. Store aw ay from
incompatible materials.
Inhalation: Inhalation of vapors or mists of the product may be irritating to the respiratory system.
Skin contact: Causes skin irritation. May cause allergic skin reaction.
Eye contact: Causes serious eye irritation.
Ingestion: May cause gastrointestinal tract irritation if sw allowed.
Hazardous Component(s) LD50s and LC50s Im m ediate and Delayed Health Effects
Polyglycol dioctanoate None Irritant
Allergen, Central nervous system, Corrosive,
Cumene hydroperoxide None
Irritant, Mutagen
Saccharin Oral LD50 (Mouse) = 17 g/kg No Target Organs
Oral LD50 (Rat) = 2.91 g/kg
Cumene Central nervous system, Irritant, Lung
Oral LD50 (Rat) = 1,400 mg/kg
Oral LD50 (Rat) = 7,800 mg/kg
Allergen, Irritant, Kidney, Liver, Mutagen,
Methyl methacrylate Oral LD50 (Rabbit) = 6,000 mg/kg
Nervous System, Respiratory
Oral LD50 (Rat) = 9,400 mg/kg
OSHA Carcinogen
Hazardous Component(s) NTP Carcinogen IARC Carcinogen
(Specifically Regulated)
Polyglycol dioctanoate No No No
Cumene hydroperoxide No No No
Saccharin No No No
Reasonably Anticipated to be
Cumene Group 2B No
a Human Carcinogen.
Methyl methacrylate No No No
Recom mended method of disposal: Follow all local, state, federal and provincial regulations for disposal.
TSCA 8 (b) Inventory Status: All components are listed as active or are exempt from listing on the Toxic Substances
Control Act (TSCA) inventory.
TSCA 12 (b) Export Notification: None above reporting de minimis
California Proposition 65: This product contains a chemical know n in the State of California to cause cancer. This
product contains a chemical know n to the State of California to cause birth defects or other
reproductive harm.
CEPA DSL/NDSL Status: All components are listed on or are exempt from listing on the Canadian Domestic
Substances List.
This Safety Data Sheet has been generated based on OSHA Hazard Communication Standard (29 CFR 1910.1200) and provides
information in accordance with U.S. federal law only. No w arranty or representation of any kind is given w ith respect to the
substantive or export law s of any other jurisdiction or country. Please confirm that the information provided herein conforms to the
substantive export or other law of any other jurisdiction prior to export. Please contact Henkel Product Safety and Regulatory
Affairs for additional assistance.
2. HAZARDS IDENTIFICATION
EMERGENCY OVERVIEW
WARNING: CAUSES SKIN IRRITATION.
MAY CAUSE AN ALLERGIC SKIN REACTION.
CAUSES SERIOUS EYE IRRITATION.
SUSPECTED OF CAUSING CANCER.
MAY CAUSE DAMAGE TO ORGANS THROUGH PROLONGED OR
REPEATED EXPOSURE.
PICTOGRAM(S)
Precautionary Statements
Prevention: Obtain special instructions before use. Do not handle until all safety precautions have been
read and understood. Do not breathe vapors, mist, or spray. Wash affected area thoroughly
after handling. Contaminated work clothing should not be allowed out of the workplace. Wear
protective gloves, clothing, eye and face protection.
Response: IF ON SKIN: Wash with plenty of water. IF IN EYES: Rinse cautiously with water for several
minutes. Remove contact lenses, if present and easy to do. Continue rinsing. IF exposed or
concerned: Get medical attention. If skin irritation or rash occurs: Get medical attention. If eye
irritation persists: Get medical attention. Take off contaminated clothing.
Storage: Store locked up.
Disposal: Dispose of contents and/or container according to Federal, State/Provincial and local
governmental regulations.
IDH number: 1395405 Product name: LOCTITE® QUICKTAPE™ 249™ THREADLOCKER TAPE
Page 1 of 6
Classification complies with OSHA Hazard Communication Standard (29 CFR 1910.1200) and is consistent with the provisions of the
United Nations Globally Harmonized System of Classification and Labeling of Chemicals (GHS).
* Exact percentages may vary or are trade secret. Concentration range is provided to assist users in providing appropriate protections.
Skin contact: Remove contaminated clothing and footwear. Immediately flush skin with
plenty of water (using soap, if available). Wash clothing before reuse. Get
medical attention.
Eye contact: Rinse immediately with plenty of water, also under the eyelids, for at least 15
minutes. Get medical attention.
Special firefighting procedures: Wear self-contained breathing apparatus and full protective clothing, such as
turn-out gear.
Unusual fire or explosion hazards: In case of fire, keep containers cool with water spray.
Hazardous combustion products: Oxides of carbon. Oxides of nitrogen. Hydrogen cyanide. Hydrocarbons.
Irritating organic vapours.
IDH number: 1395405 Product name: LOCTITE® QUICKTAPE™ 249™ THREADLOCKER TAPE
Page 2 of 6
Clean-up methods: Remove all sources of ignition. Evacuate and ventilate spill area; dike spill to
prevent entry into water system; wear full protective equipment during clean-
up. Refer to Section 8 "Exposure Controls / Personal Protection" prior to clean
up. Soak up with inert absorbent material (e.g. sand, silica gel, acid binder,
universal binder, sawdust). Store in a partly filled, closed container until
disposal.
For information on product shelf life contact Henkel Customer Service at (800) 243-4874.
Engineering controls: Provide adequate local exhaust ventilation to maintain worker exposure below
exposure limits.
Respiratory protection: Use NIOSH approved respirator if there is potential to exceed exposure
limit(s).
Eye/face protection: Safety goggles or safety glasses with side shields. Safety showers and eye
wash stations should be available.
Skin protection: Use chemical resistant, impermeable clothing including gloves and either an
apron or body suit to prevent skin contact. Neoprene, Butyl-rubber, or nitrile-
rubber gloves.
IDH number: 1395405 Product name: LOCTITE® QUICKTAPE™ 249™ THREADLOCKER TAPE
Page 3 of 6
pH: Not available.
Vapor pressure: Not available.
Boiling point/range: Not available.
Melting point/ range: Not available.
Specific gravity: 1.1
Vapor density: Not available.
Flash point: Product is a solid.
Flammable/Explosive limits - lower: Not available.
Flammable/Explosive limits - upper: Not available.
Autoignition temperature: Not available.
Flammability: Not applicable
Evaporation rate: Not available.
Solubility in water: Not available.
Partition coefficient (n-octanol/water): Not available.
VOC content: 5 g/l (calculated)
Viscosity: Not available.
Decomposition temperature: Not available.
Hazardous reactions: None under normal processing. Polymerization may occur at elevated temperature or in the
presence of incompatible materials.
Hazardous decomposition Oxides of carbon. Oxides of nitrogen. Hydrocarbons. Irritating organic vapours.
products:
Incompatible materials: Strong oxidizing agents. Reducing agents. Aldehydes. Amines. Alkalis. Peroxides. Free radical
initiators.
Conditions to avoid: Heat, flames, sparks and other sources of ignition. Store away from incompatible materials.
IDH number: 1395405 Product name: LOCTITE® QUICKTAPE™ 249™ THREADLOCKER TAPE
Page 4 of 6
Potential Health Effects/Symptoms
Inhalation: Inhalation of vapors or mists of the product may be irritating to the respiratory system.
Skin contact: Causes skin irritation. May cause allergic skin reaction.
Eye contact: Causes serious eye irritation.
Ingestion: May cause gastrointestinal disturbances.
Hazardous Component(s) LD50s and LC50s Immediate and Delayed Health Effects
Silica, amorphous, fumed, crystal-free None Nuisance dust
Allergen, Central nervous system, Corrosive,
Cumene hydroperoxide Inhalation LC50 (Mouse, 4 h) = 200 mg/l
Irritant, Mutagen
Ethene, tetrafluoro-, homopolymer None No Target Organs
Saccharin Oral LD50 (Mouse) = 17 g/kg No Target Organs
Oral LD50 (Rat) = 2.91 g/kg
Cumene Oral LD50 (Rat) = 1,400 mg/kg Central nervous system, Irritant, Lung
Inhalation LC50 (Rat, 4 h) = 8000 ppm
Allergen, Blood, Kidney, Mutagen, Some
1-Acetyl-2-phenylhydrazine Oral LD50 (Mouse) = 270 mg/kg
evidence of carcinogenicity
Oral LD50 (Mouse) = 670 mg/kg
Oral LD50 (Rat) = 2,300 - 3,500 mg/kg
Methyl ethyl ketone Oral LD50 (Rat) = 4,500 - 6,800 mg/kg Irritant, Central nervous system
Dermal LD50 (Rabbit) = > 8,000 mg/kg
Inhalation LC50 (Rat, 4 h) = 11700 ppm
OSHA Carcinogen
Hazardous Component(s) NTP Carcinogen IARC Carcinogen
(Specifically Regulated)
Silica, amorphous, fumed, crystal-free No No No
Cumene hydroperoxide No No No
Ethene, tetrafluoro-, homopolymer No No No
Saccharin No No No
Reasonably Anticipated to be
Cumene Group 2B No
a Human Carcinogen.
1-Acetyl-2-phenylhydrazine No No No
Methyl ethyl ketone No No No
Recommended method of disposal: Follow all local, state, federal and provincial regulations for disposal.
Hazardous waste number: This product contains a component or components identified as hazardous
under 40 CFR 261.24. D035: Methyl Ethyl Ketone.
IDH number: 1395405 Product name: LOCTITE® QUICKTAPE™ 249™ THREADLOCKER TAPE
Page 5 of 6
International Air Transportation (ICAO/IATA)
Proper shipping name: RQ, Environmentally hazardous substance, solid, n.o.s.
Hazard class or division: 9
Identification number: UN 3077
Packing group: III
TSCA 8 (b) Inventory Status: All components are listed or are exempt from listing on the Toxic Substances Control Act
Inventory.
TSCA 12 (b) Export Notification: Ethene, tetrafluoro-, homopolymer (CAS# 9002-84-0).
California Proposition 65: This product contains a chemical known in the State of California to cause cancer. This
product contains a chemical known to the State of California to cause birth defects or other
reproductive harm.
CEPA DSL/NDSL Status: One or more components are not listed on, and are not exempt from listing on either the
Domestic Substances List or the Non-Domestic Substances List.
DISCLAIMER: The data contained herein are furnished for information only and are believed to be reliable. However, Henkel
Corporation and its affiliates (“Henkel”) does not assume responsibility for any results obtained by persons over whose methods
Henkel has no control. It is the user’s responsibility to determine the suitability of Henkel’s products or any production methods
mentioned herein for a particular purpose, and to adopt such precautions as may be advisable for the protection of property and
persons against any hazards that may be involved in the handling and use of any Henkel’s products. In light of the foregoing,
Henkel specifically disclaims all warranties, express or implied, including warranties of merchantability and fitness for a particular
purpose, arising from sale or use of Henkel’s products. Henkel further disclaims any liability for consequential or incidental damages
of any kind, including lost profits.
IDH number: 1395405 Product name: LOCTITE® QUICKTAPE™ 249™ THREADLOCKER TAPE
Page 6 of 6
Safety Data Sheet
2. HAZARDS IDENTIFICATION
EMERGENCY OVERVIEW
WARNING: CAUSES SKIN IRRITATION.
MAY CAUSE AN ALLERGIC SKIN REACTION.
CAUSES SERIOUS EYE IRRITATION.
SUSPECTED OF CAUSING CANCER.
PICTOGRAM(S)
Precautionary Statements
Prevention: Obtain special instructions before use. Do not handle until all safety precautions have been
read and understood. Avoid breathing vapors, mist, or spray. Wash affected area thoroughly
after handling. Contaminated work clothing should not be allowed out of the workplace. Wear
protective gloves, clothing, eye and face protection.
Response: IF ON SKIN: Wash with plenty of water. IF IN EYES: Rinse cautiously with water for several
minutes. Remove contact lenses, if present and easy to do. Continue rinsing. IF exposed or
concerned: Get medical attention. If skin irritation or rash occurs: Get medical attention. If eye
irritation persists: Get medical attention. Take off contaminated clothing.
Storage: Store locked up.
Disposal: Dispose of contents and/or container according to Federal, State/Provincial and local
governmental regulations.
Classification complies with OSHA Hazard Communication Standard (29 CFR 1910.1200) and is consistent with the provisions of the
United Nations Globally Harmonized System of Classification and Labeling of Chemicals (GHS).
* Exact percentages may vary or are trade secret. Concentration range is provided to assist users in providing appropriate protections.
Skin contact: Remove contaminated clothing and footwear. Immediately flush skin with
plenty of water (using soap, if available). Wash clothing before reuse. Get
medical attention.
Eye contact: Rinse immediately with plenty of water, also under the eyelids, for at least 15
minutes. Get medical attention.
Special firefighting procedures: Wear self-contained breathing apparatus and full protective clothing, such as
turn-out gear. In case of fire, keep containers cool with water spray.
Unusual fire or explosion hazards: Uncontrolled polymerization may occur at high temperatures resulting in
explosions or rupture of storage containers.
Hazardous combustion products: Oxides of carbon. Oxides of sulfur. Oxides of nitrogen. Irritating organic
fragments.
Clean-up methods: Remove all sources of ignition. Evacuate and ventilate spill area; dike spill to
prevent entry into water system; wear full protective equipment during clean-
up. Refer to Section 8 "Exposure Controls / Personal Protection" prior to clean
up. Soak up with inert absorbent material (e.g. sand, silica gel, acid binder,
universal binder, sawdust). Store in a partly filled, closed container until
disposal.
Engineering controls: Provide adequate local exhaust ventilation to maintain worker exposure below
exposure limits.
Respiratory protection: Use NIOSH approved respirator if there is potential to exceed exposure
limit(s).
Eye/face protection: Safety goggles or safety glasses with side shields. Full face protection should
be used if the potential for splashing or spraying of product exists. Safety
showers and eye wash stations should be available.
Skin protection: Use chemical resistant, impermeable clothing including gloves and either an
apron or body suit to prevent skin contact. Butyl rubber gloves. Neoprene
gloves. Natural rubber gloves.
Hazardous reactions: None under normal processing. Polymerization may occur at elevated temperature or in the
presence of incompatible materials.
Hazardous decomposition Oxides of carbon. Oxides of nitrogen. Oxides of sulfur. Irritating organic fragments.
products:
Incompatible materials: Strong oxidizing agents. Reducing agents. Strong alkalis. Oxygen scavengers. Other
polymerization initiators. Heavy metals.
Conditions to avoid: Elevated temperatures. Heat, flames, sparks and other sources of ignition. Store away from
incompatible materials.
Inhalation: Inhalation of vapors or mists of the product may be irritating to the respiratory system.
Skin contact: Causes skin irritation. May cause allergic skin reaction.
Eye contact: Causes serious eye irritation.
Ingestion: May cause gastrointestinal tract irritation if swallowed.
Hazardous Component(s) LD50s and LC50s Immediate and Delayed Health Effects
Tetramethylene dimethacrylate None Irritant, Allergen
Amorphous fumed silica None No Target Organs
Ethene, homopolymer None No Target Organs
Oral LD50 (Rabbit) = 18 g/kg
Propane-1,2-diol Oral LD50 (Mouse) = 23.9 g/kg Irritant
Oral LD50 (Rat) = 30 g/kg
Allergen, Central nervous system, Corrosive,
Cumene hydroperoxide None
Irritant, Mutagen
Allergen, Blood, Kidney, Mutagen, Some
1-Acetyl-2-phenylhydrazine Oral LD50 (Mouse) = 270 mg/kg
evidence of carcinogenicity
Oral LD50 (Rat) = 2.91 g/kg
Cumene Central nervous system, Irritant, Lung
Oral LD50 (Rat) = 1,400 mg/kg
OSHA Carcinogen
Hazardous Component(s) NTP Carcinogen IARC Carcinogen
(Specifically Regulated)
Tetramethylene dimethacrylate No No No
Amorphous fumed silica No No No
Ethene, homopolymer No No No
Propane-1,2-diol No No No
Cumene hydroperoxide No No No
1-Acetyl-2-phenylhydrazine No No No
Reasonably Anticipated to be
Cumene Group 2B No
a Human Carcinogen.
Recommended method of disposal: Follow all local, state, federal and provincial regulations for disposal.
TSCA 8 (b) Inventory Status: All components are listed or are exempt from listing on the Toxic Substances Control Act
Inventory.
TSCA 12 (b) Export Notification: None above reporting de minimis
California Proposition 65: This product contains a chemical known in the State of California to cause cancer. This
product contains a chemical known to the State of California to cause birth defects or other
reproductive harm.
CEPA DSL/NDSL Status: All components are listed on or are exempt from listing on the Canadian Domestic
Substances List.
DISCLAIMER: The data contained herein are furnished for information only and are believed to be reliable. However, Henkel
Corporation and its affiliates (“Henkel”) does not assume responsibility for any results obtained by persons over whose methods
Henkel has no control. It is the user’s responsibility to determine the suitability of Henkel’s products or any production methods
mentioned herein for a particular purpose, and to adopt such precautions as may be advisable for the protection of property and
persons against any hazards that may be involved in the handling and use of any Henkel’s products. In light of the foregoing,
Henkel specifically disclaims all warranties, express or implied, including warranties of merchantability and fitness for a particular
purpose, arising from sale or use of Henkel’s products. Henkel further disclaims any liability for consequential or incidental damages
of any kind, including lost profits.
This Safety Data Sheet has been generated based on OSHA Hazard Communication Standard (29 CFR 1910.1200) and provides
information in accordance with U.S. federal law only. No warranty or representation of any kind is given with respect to the
substantive or export laws of any other jurisdiction or country. Please confirm that the information provided herein conforms to the
substantive export or other law of any other jurisdiction prior to export. Please contact Henkel Product Safety and Regulatory
Affairs for additional assistance.
2. HAZARDS IDENTIFICATION
EMERGENCY OVERVIEW
WARNING: CAUSES SKIN IRRITATION.
CAUSES SERIOUS EYE IRRITATION.
PICTOGRAM(S)
Precautionary Statements
Prevention: Wash affected area thoroughly after handling. Wear protective gloves, eye protection, and face
protection.
Response: IF ON SKIN: Wash w ith plenty of water. IF IN EYES: Rinse cautiously w ith water for several
minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If skin irritation
occurs: Get medical attention. If eye irritation persists: Get medical attention. Take off
contaminated clothing.
Storage: Not prescribed
Disposal: Not prescribed
Classification complies w ith OSHA Hazard Communication Standard (29 CFR 1910.1200) and is consistent with the provisions of the
United Nations Globally Harmonized System of Classification and Labeling of Chemicals (GHS).
IDH number: 466863 Product name: LOCTITE LB 8065 COPPER ANTI-SEIZE STICK know n as C5-A® Copper Anti-Seize
Stick
Page 1 of 6
Distillates (petroleum), hydrotreated
64742-52-5 10 - 30
heavy naphthenic
Petroleum distillates, hydrotreated, light
64742-53-6 10 - 30
naphthenic
Quartz (SiO2) 14808-60-7 0.1 - 1
* Exact percentages may vary or are trade secret. Concentration range is provided to assist users in providing appropriate pr otections.
Skin contact: Wash w ith soap and w ater. If symptoms develop and persist, get medical
attention.
Eye contact: Immediately flush eyes w ith plenty of water for at least 15 minutes. Get
medical attention.
Ingestion: Do not induce vomiting. Aspiration may cause pulmonary edema and
pneumonitis. Get medical attention.
Clean-up methods: Refer to Section 8 "Exposure Controls / Personal Protection" prior to clean up.
For large spills absorb onto inert absorbent material and place in sealed
container for disposal. For small spills w ipe up w ith paper towel and place in
container for disposal. Scrape up as much material as possible. Clean
residue w ith soap and w ater.
IDH number: 466863 Product name: LOCTITE LB 8065 COPPER ANTI-SEIZE STICK know n as C5-A® Copper Anti-Seize
Stick
Page 2 of 6
8. EXPOSURE CONTROLS / PERSONAL PROTECTION
Em ployers should complete an assessment of all w orkplaces to determine the need for, and selection of, proper exposure
controls and protective equipment for each task performed.
Engineering controls: Use only w ith adequate ventilation. Local exhaust ventilation is recommended
w hen general ventilation is not sufficient to control airborne contamination
below occupational exposure limits.
Respiratory protection: Use NIOSH approved respirator if there is potential to exceed exposure
limit(s). Observe OSHA regulations for respirator use (29 CFR 1910.134).
Eye/face protection: Safety goggles or safety glasses with side shields. Full face protection should
be used if the potential for splashing or spraying of product exists.
Skin protection: Use impermeable gloves and protective clothing as necessary to prevent skin
contact.
IDH number: 466863 Product name: LOCTITE LB 8065 COPPER ANTI-SEIZE STICK know n as C5-A® Copper Anti-Seize
Stick
Page 3 of 6
Partition coefficient (n-octanol/water): Not determined
VOC content: 0%
Viscosity: Not available.
Decom position temperature: Not available.
Inhalation: Inhalation of copper fumes may result in metal fume fever. Symptoms include metallic taste,
discoloration of skin or hair. This product has low volatility and is not expected to cause
respiratory tract irritation during normal conditions of use. May cause respiratory tract irritation.
Abrasion of cured material such as by sanding or grinding could release respirable partic les of
silica quartz, a cancer hazard by inhalation. Normal use of this product causes no such release.
Skin contact: Causes skin irritation.
Eye contact: Causes serious eye irritation.
Ingestion: May cause gastrointestinal tract irritation if sw allowed. Principal hazard of ingestion is
aspiration into the lungs and subsequent pneumonitis.
Hazardous Component(s) LD50s and LC50s Im m ediate and Delayed Health Effects
Allergen, Blood, Central nervous system,
Developmental, Gastrointestinal, Immune
Copper None
system, Irritant, Kidney, Liver, Mutagen,
Sensory, Skin
Inhalation LC50 (Rat, 4 h) = > 2,000 mg/m3
Graphite Lung
Inhalation LC50 (Rat, 4 h) = > 2,000 mg/m3
Distillates (petroleum), hydrotreated
None Irritant
heavy naphthenic
Petroleum distillates, hydrotreated, light
None Irritant
naphthenic
Immune system, Lung, Some evidence of
Quartz (SiO2) None
carcinogenicity
OSHA Carcinogen
Hazardous Component(s) NTP Carcinogen IARC Carcinogen
(Specifically Regulated)
Copper No No No
Graphite No No No
Distillates (petroleum), hydrotreated
No No No
heavy naphthenic
Petroleum distillates, hydrotreated, light
No No No
naphthenic
Know n To Be Human
Quartz (SiO2) Group 1 Yes
Carcinogen.
IDH number: 466863 Product name: LOCTITE LB 8065 COPPER ANTI-SEIZE STICK know n as C5-A® Copper Anti-Seize
Stick
Page 4 of 6
12. ECOLOGICAL INFORMATION
Ecological inform ation: Not available.
Recom mended method of disposal: Follow all local, state, federal and provincial regulations for disposal.
TSCA 8 (b) Inventory Status: All components are listed or are exempt from listing on the Toxic Substances Control Act
Inventory.
TSCA 12 (b) Export Notification: None above reporting de minimis
California Proposition 65: This product contains a chemical know n in the State of California to cause cancer.
CEPA DSL/NDSL Status: All components are listed on or are exempt from listing on the Canadian Domestic
Substances List.
IDH number: 466863 Product name: LOCTITE LB 8065 COPPER ANTI-SEIZE STICK know n as C5-A® Copper Anti-Seize
Stick
Page 5 of 6
Prepared by: Product Safety and Regulatory Affairs
DISCLAIMER: The data contained herein are furnished for information only and are believed to be reliable. How ever, Henkel
Corporation and its affiliates (“Henkel”) does not assume responsibility for any results obtained by persons over whose methods
Henkel has no control. It is the user’s responsibility to determine the suitability of Henkel’s products or any production methods
mentioned herein for a particular purpose, and to adopt such precautions as may be advisable for the protection of property and
persons against any hazards that may be involved in the handling and use of any Henkel’s products. In light of the foregoing,
Henkel specifically disclaims all w arranties, express or implied, including w arranties of merchantability and fitness for a particular
purpose, arising from sale or use of Henkel’s products. Henkel further disclaims any liability for consequential or incidental damages
of any kind, including lost profits.
This Safety Data Sheet has been generated based on OSHA Hazard Communication Standard (29 CFR 1910.1200) and provides
information in accordance with U.S. federal law only. No w arranty or representation of any kind is given w ith respect to the
substantive or export law s of any other jurisdiction or country. Please confirm that the information provided herein conforms to the
substantive export or other law of any other jurisdiction prior to export. Please contact Henkel Product Safety and Regulatory
Affairs for additional assistance.
IDH number: 466863 Product name: LOCTITE LB 8065 COPPER ANTI-SEIZE STICK know n as C5-A® Copper Anti-Seize
Stick
Page 6 of 6