Crouse Hinds Powermate Drilling Pin Sleeve Brochure
Crouse Hinds Powermate Drilling Pin Sleeve Brochure
PowerMate™
drilling pin and
sleeve connectors
Safe. Reliable. Fast.
Connections
The ideal rig power connection solution
• Longer product life • Enhanced safety
• Reduced maintenance • Easy to install
Insulator assemblies
• Unimpeded, easy-access phase and ground terminals make wire
termination quick and easy.
• Molded-in-place markings for phase/ground and conductor strip
lengths reduce installation errors. (60, 100 and 150A only)
Exclusive features
8-point diamond cable clamps Lockout plug
• 8 points of contact around diameter of cable • Guarantees isolated power supply with
for increased grip and even distribution of OSHA compliant lockout/tagout.
pressure. • Ensures plug cannot be inserted into
• Cable jacket does not get pinched, eliminating receptacle when maintenance is being
potential for damage to internal conductors. performed downstream of power supply.
Standard materials
• Receptacle housing, plug and cord connector bodies - high
impact strength copper-free aluminum (less than 0.4% copper)
CDR-RS
• Back boxes - cast aluminum reverse service receptacle
• Insulation - fiberglass reinforced polyester (male contacts)
Easy to connect
• Sloted screwdriver
holds cap open
Spring cap
• Spring cap with stainless steel
hardware and wing nuts to
ensure proper environmental
sealing
Easy to wire
• Gaps in insulator allow easy
access to wire terminals
• Body breaks into two pieces,
facilitating cable installation
CCP3034BC–RS
Eaton's Crouse-Hinds PowerMate™ plug, 30A, 3 wire, 4 pole, 0.390-1.375" cable range, reverse service
50 ½"
75 ¾"
Amperage 100 1"
30 30 Amp 125 1-¼"
Cable range
60 60 Amp (plug & connector only)* 150 1-½"
10 100 Amp BC 0.390 to 1.375" 200 2"
150 150 Amp CD 0.875 to 1.906" 250 2-½"
200 200 Amp DE 1.250 to 2.190" 300 3"
E 1.875 to 2.500" 350 3-½"
F 2.500 to 3.000" 400 4"
G 3.000 to 3.500" 500 5"
* Cable range only applies to specific * Hub size only applies to specific
plug part numbers receptacle part numbers
Maximum horsepower for plug and receptacle combinations by Style 1 units complete the grounding circuit through the metallic plug shell,
input voltage receptacle housing or connector shell
Typical horsepower ratings Motor horsepower**
Amp
based on NEC Article 430 tables. rating 240V 480V 600V
HP ratings are based on the
largest conductor size for each 30 15 30 40
plug and receptacle combination.
60 20 40 50
style 2
3 wire
• Standard Corro-Free™ epoxy
powder coat finish for increased
3 pole CDR3033 0.390-1.375” CCP3033BC 0.390-1.375” CRC3033BC
corrosion resistance
style 1
• For optional reversed interior,
3 wire
use suffix -RS
4 pole CDR3034 0.390-1.375” CCP3034BC 0.390-1.375” CRC3034BC
style 2 • For optional rotated interior, use
suffix -P4
4 wire
4 pole CDR3044 0.390-1.375” CCP3044BC 0.390-1.375” CRC3044BC • Maximum conductor size (wire
style 1 well) 0.281”
2 wire
1-½" CEE56 CERH56 CJA510 CERC56
3 pole CDR6023 0.440-1.375” CCP6023BC 0.440-1.375” CRC6023BC
style 2
2" – – CJA610 –
3 wire
3 pole CDR6033 0.440-1.375” CCP6033BC 0.440-1.375” CRC6033BC
• Standard Corro-Free™ epoxy powder coat
style 1 finish for increased corrosion resistance
3 wire, • For optional reversed interior, use suffix -RS
4 pole CDR6034 0.440-1.375” CCP6034BC 0.440-1.375” CRC6034BC
style 2 • For optional rotated interior, use suffix -P4
4 wire • Maximum conductor size (wire well) 0.312”
4 pole CDR6044 0.440-1.375” CCP6044BC 0.440-1.375” CRC6044BC
style 1
style 2
2" CJA610
3 wire
3 pole CDR1033 0.875-1.906” CCP1033CD 0.875-1.906” CRC1033CD
• Standard Corro-Free™ epoxy
style 1
powder coat finish for increased
3 wire corrosion resistance
4 pole CDR1034 0.875-1.906” CCP1034CD 0.875-1.906” CRC1034CD
• For optional reversed interior, use
style 2 suffix -RS
4 wire • For optional rotated interior, use
4 pole CDR1044 0.875-1.906” CCP1044CD 0.875-1.906” CRC1044CD
suffix -P4
style 1
• Maximum conductor size (wire
well) 0.390”
A A A
B B B
60A, 3 pole 4.2500 4.5000 60A, 3 pole 8.1700 3.6250 60A, 3 pole 08.300 2.3125
60A, 4 pole 4.2500 4.5000 60A, 4 pole 8.1700 3.7500 60A, 4 pole 8.3000 2.3125
100A, 3 pole 5.2500 4.2500 100A, 3 pole 10.8000 3.7500 100A, 3 pole 11.5000 3.1875
100A, 4 pole 5.2500 4.2500 100A, 4 pole 10.8000 4.1250 100A, 4 pole 11.5000 3.4375
Back boxes with 60, 100, 150 & 200A angle adapters
Hub
Part number Rating Size A B C D E F
60, 100,
CJA310 1" 5.8750 8.0000 7.4375 4.8750 7.0000 15°
150A
60, 100,
CJA410 1-¼" 5.8750 8.0000 7.4375 4.8750 7.0000 15°
150A
60, 100,
CJA510 1-½" 5.8750 8.0000 7.4375 4.8750 7.0000 15°
150A
60, 100,
CJA610 2" 5.8750 8.0000 8.0000 4.8750 7.0000 15° • Back boxes are standard with Corro-Free™
150A
epoxy powder coat finish for increased
CJA520 200A 1-½" 8.0000 10.7500 9.8750 6.7500 9.5000 45° corrosion resistance
• Through feed back boxes are furnished
CJA620 200A 2" 8.0000 10.7500 9.8750 6.7500 9.5000 45°
with one close-up plug in bottom recessed
CJA720 200A 2-½" 8.0000 10.7500 9.8750 6.7500 9.5000 45° hub
• CJA back boxes are recommended when
CJAC720 200A 2-½" 8.0000 10.7500 9.8750 6.7500 9.5000 45° additional wiring space is required
• The angle adapter on CJA back boxes can
be installed at 90° rotations, making it
possible to enter hub from several
directions
powering
solutions
4 Motor Control/VFD/SCR House
Doghouse/
5 Operator's House
6 Power/Pump Station
3
7 Shale Shaker
4 2
5
8 Mud Tanks/Pumps
10
6
7 9
9 Drawworks & Top Drive
8
10 Drilling Floor
Eaton
1000 Eaton Boulevard
Cleveland, OH 44122
United States
Eaton.com
© 2018 Eaton
All Rights Reserved Eaton is a registered trademark.
Printed in USA
Publication No. 5163-0318 All other trademarks are property
March 2018 of their respective owners.