PI-NL2208CK - Quick Start Guide Version
PI-NL2208CK - Quick Start Guide Version
PI-NL2208CK - Quick Start Guide Version
i
Welcome
Thank you for purchasing our network video Recorder (Without Harddisk)!
This quick start guide is designed to be a reference tool for your system.
Please open the accessory bag to check the items one by one in accordance with the list below.
Contact your local retailer ASAP if something is missing or damaged in the bag.
ii
Important Safeguards and Warnings
1.Electrical safety
All installation and operation here should conform to your local electrical safety codes.
The product must be grounded to reduce the risk of electric shock.
We assume no liability or responsibility for all the fires or electrical shock caused by improper
handling or installation.
2.Transportation security
Heavy stress, violent vibration or water splash are not allowed during transportation, storage and
installation.
3.Installation
Keep upwards. Handle with care.
Do not apply power to the NVR (WITHOUT HARDDISK) before completing installation.
Do not place objects on the NVR (WITHOUT HARDDISK).
5.Environment
The NVR (WITHOUT HARDDISK) should be installed in a cool, dry place away from direct
sunlight, inflammable, explosive substances and etc.
This series product shall be transported, storage and used in the specified environments.
6. Accessories
Be sure to use all the accessories recommended by manufacturer.
Before installation, please open the package and check all the components are included.
Contact your local retailer ASAP if something is broken in your package.
7. Lithium battery
Improper battery use may result in fire, explosion, or personal injury!
When replace the battery, please make sure you are using the same model!
CAUTION
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
iii
Do not put other devices on the top of the NVR (WITHOUT HARDDISK);
Be installed in well ventilated place; do not block the vent.
Accessories
Check the accessories after opening the box:
Please refer to the packing list in the box *
iv
Table of Contents
2 Connection Sample.......................................................................................................... 6
v
1 Hardware Installation and Connection
Note: All the installation and operations here should conform to your local electric
safety rules.
1
1.4 HDD Installation
Important:
Please turn off the power before you replace the HDD.
The pictures listed below for reference only
You can refer to the User’s Manual for recommended HDD brand. Please use HDD of 7200rpm or higher.
Usually we do not recommend the PC HDD.
For detailed operation instruction, please refer to the User’s Manual included in the resources CD.
1. Loosen the screws of the upper 2. Fix four screws in the HDD 3. Place the HDD in
cover and side panel. (Turn just three rounds). accordance with the four
holes in the bottom.
4. Turn the device upside down and 5. Fix the HDD firmly. 6. Connect the HDD cable
then turn the screws in firmly. and power cable.
7. Put the cover in accordance with 8. Secure the screws in the rear
the clip and then place the upper panel and the side panel.
cover back.
④After connect the cable, put the front cover back to the device and then fix screws of the rear panel.
2
1.5 Front Panel
For detailed operation instruction, please refer to the User’s Manual included in the resources CD.
The front panel is shown as in Figure 1-1.
Figure 1-1
Please refer to the following sheet for front panel button information.
3
Backspace function: in numeral control or text control, press it for
1.5seconds to delete the previous character before the cursor.
Network
Network error occurs or there is no network connection, the light
abnormal Net
becomes red to alert you.
indicator light
HDD abnormal HDD error occurs or HDD capacity is below specified threshold
HDD
indicator light value, the light becomes red to alert you.
4
1.6 Rear Panel
The PI-NL2208K series rear panel is shown as below. See Figure 1-10.
Figure 1-10
5
2 Connection Sample
Please refer to Figure 2 for connection sample. The following figure is based on our PI-NL2208CK product.
Figure 2
6
3 GUI Operation
3.1 Boot up
Caution
Before the boot up, please make sure:
For device security, please connect the NVR (WITHOUT HARDDISK) to the power adapter first
and then connect the device to the power socket.
The rated input voltage matches the device power on-off button. Please make sure the power
wire connection is OK. Then click the power on-off button.
Always use the stable current, if necessary UPS is a best alternative measure.
After device booted up, the system goes to startup wizard interface. See Figure 3-1. Click Cancel or Next Step
button, you can see system goes to login interface.
Tips
Check the box Startup button here, system goes to startup wizard again when it boots up the next time.
Cancel the Startup button, system goes to the login interface directly when it boots up the next time.
Figure 3-1
Click Cancel button or Next Step, you can see the login interface. Please input user name and password. See Figure
3-2.
7
Username: ADMIN. Password: 12345.
You can use USB mouse to input. Click to switch between numeral, English character (small/capitalized) and
denotation.
Figure 3-2
Important:
For security reason, please modify password after you first login.
Within 30 minutes, three times login failure will result in system alarm and five times login failure will
result in account lock!
Figure 3-3
Tips
In the preview interface, for the channel of no IPC connection, you can click the icon “+” in the centre of the
interface to quickly go to the Remote Device interface. See Figure 3-4.
8
Figure 3-4
Click Device Search button, you can view the searched IP addresses at the top pane of the interface. Double click an
IP address or check one IP address and then click Add button, you can add current device to the bottom pane of the
interface. System supports batch add function.
Click Manual Add button, you can add a device directly. See Figure 3-5.
Important
Please note the manual add function is for Panasonic, CPPlus, Dahua, Sony, Dynacolor, Samsung, Axis, Arecont,
ONVIF and custom. When the type is the custom, you can just input URL address, user name and password connect
to the network camera without considering network camera manufacture. Please contact your network camera
manufacturer for the URL address.
Figure 3-5
9
4 Web Operation
Important
This series NVR (WITHOUT HARDDISK) product support the Web access and management via PC.
Web includes several modules: Monitor channel preview, record search, alarm setup, system configuration, PTZ
control, monitor window and etc.
4.2 Login
Open IE and input NVR (WITHOUT HARDDISK) address in the address column. For example, if your NVR (WITHOUT
HARDDISK) IP is 10.10.3.16, then please input http:// 10.10.3.16 in IE address column.
System pops up warning information to ask you whether install Web plug-in or not. Please click yes button.
If you can’t download the ActiveX file, please modify your IE security setup. After installation, the interface is shown
as below. See Figure 4-1.
Please input your user name and password. Default factory name is ADMIN and password is 12345.
Note: For security reasons, please modify your password after you first login.
10
Figure 4-1
For the LAN mode, after you logged in, you can see the main window. See Figure 4-2.
Click the channel name on the left side; you can view the real-time video.
Figure 4-2
11
4.3.2 WAN Login
In WAN mode, after you logged in, the interface is shown as below. See Figure 4-3.
Figure 4-3
For detailed operation information, please refer to the User’s Manual included in the resources CD.
Note
For detailed operation introduction, please refer to our resource CD included in your package for electronic
version of the User’s Manual.
Slight difference may be found in user interface.
All the designs and software here are subject to change without prior written notice.
All trademarks and registered trademarks are the properties of their respective owners.
If there is any uncertainty or controversy, please refer to the final explanation of us.
Please visit our website or contact your local service engineer for more information.
12