Scribd Logo
Upload

Welcome to Scribd!

  • Download

    Uploaded by

    Charmpas Dimitrios
    13 views5 pages

    Original Title

    Download (3)

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Flag for inappropriate content
    Download as pdf or txt
    13 views5 pages

    Download

    Uploaded by

    Charmpas Dimitrios

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Flag for inappropriate content
    Download as pdf or txt
    of 5

    TECHNICAL BULLETIN SU-15-08

    21 April 2015

    MODEL AFFECTED: UH-1H

    SUBJECT: ALTERNATE SPARE PART; SWASHPLATE


    GIMBAL RING ASSEMBLY P/N 212-010-416-101

    HELICOPTERS AFFECTED: UH-1H helicopters which are non-type certificated


    and owned and operated by other than an Armed
    Service of the United States.

    COMPLIANCE: At customer’s option, use Gimbal Ring Assembly P/N


    212-010-416-101 as an alternate spare part in lieu of
    Gimbal Ring Assembly P/N 204-010-404-003.

    DESCRIPTION:

    This Special Use (SU) Technical Bulletin (TB) provides authorization to UH-1H
    helicopter operators, as described in the HELICOPTERS AFFECTED block above, who
    wish to use Swashplate Gimbal Ring Assembly P/N 212-010-416-101 as an alternate
    spare part in lieu of Swashplate Gimbal Ring Assembly P/N 204-010-404-003.

    The assigned retirement life for the P/N 212-010-416-101 Swashplate Gimbal Ring
    Assembly when installed on the UH-1H is 9,000 hours.

    APPROVAL:

    Bell Helicopter does not authorize use of this bulletin to obtain approval from any civil
    regulatory authority for installation of P/N 212-010-416-101 Swashplate Gimbal Ring
    Assembly on any type certificated UH-1 helicopter.

    The engineering design aspects of this bulletin are Bell Helicopter Engineering
    approved.

    TB SU-15-08
    Page 1 of 5
    ECCN EAR99
    Approved for Public Release
    CONTACT INFO:

    For any questions regarding this bulletin, please contact:

    Bell Helicopter Product Support Engineering - Medium Military Helicopters


    Tel: 817-280-3548 / [email protected]

    MANPOWER:

    Approximately 3.0 man-hours are required to complete this bulletin. This estimate is
    based on hands-on time, and may vary with personnel and facilities available.

    No additional man hours are required when carried out at overhaul.

    WARRANTY:

    There is no warranty credit applicable for parts or labor associated with this bulletin.

    MATERIAL:

    Required Material:
    The following material is required for the accomplishment of this bulletin and may be
    obtained through your Bell Helicopter Textron Supply Center.

    Part Number Nomenclature Qty

    204-011-457-003 Washer 6
    204-011-463-001 Bolt 2
    204-011-463-003 Bolt 2
    212-010-416-101 Gimbal Ring Assembly 1

    Consumable Material:
    The following material is required to accomplish this bulletin, but may not require
    ordering, depending on the operator’s consumable material stock levels. This material
    may be obtained through your Bell Helicopter Textron Supply Center.

    Part Number Nomenclature Qty Reference *

    MIL-R-46082,TYI50CC Sealant AR C-352


    MILS46163TY11GRM Sealant AR C-299
    MS14145L5 Nut 4
    MS21318-13 Drive Screw 2
    MS24665-155 Cotter Pin 4
    NAS1149F0563P Washer 2
    * C-XXX numbers refer to the consumables list in BHT-ALL-SPM Standard Practices Manual

    TB SU-15-08
    Page 2 of 5
    ECCN EAR99
    Approved for Public Release
    SPECIAL TOOLS:

    None required

    WEIGHT AND BALANCE:

    Not Affected.

    ELECTRICAL LOAD DATA:

    Not affected.

    REFERENCES:

    TM 55-1520-210-23-1 AVUM & AVIM Maintenance Instructions


    TM 55-1520-210-23P-1 AVUM & AVIM Repair Parts and Special Tools List
    DMWR 55-1520-210 Aircraft Depot Maintenance Work Requirement
    DMWR 55-1615-221, Swashplate and Support Assembly
    Alert Service Bulletin UH-1H-15-12
    Technical Bulletin SU-95-4, Rev B

    PUBLICATIONS AFFECTED:

    TM 55-1520-210-23P-1 AVUM & AVIM Repair Parts and Special Tools List

    ACCOMPLISHMENT INSTRUCTIONS:

    1. Place swashplate and support assembly on a suitable work table.

    2. If the gimbal ring assembly is being replaced as part of a complete assembly


    overhaul, refer to DMWR 55-1615-221, Swashplate and Support Assembly, for
    procedures except as noted in steps 3.b. and 3.c. below.

    3. If the gimbal ring assembly is being replaced only, disassemble and reassemble
    swashplate and support assembly only as necessary to remove and replace the
    gimbal ring. Refer to DMWR 55-1615-221 for procedures except as noted in steps
    3.a, 3.b, and 3.c below.

    a. Refer to Figure 1. Visually inspect all parts for serviceability or evidence of


    damage; repair and/or replace unserviceable parts as required. Parts noted on
    Figure 1 as REPLACE are to be replaced regardless of serviceability.

    b. After removal of the old gimbal ring and verifying the shimming requirements of
    the bearing and liner assemblies of the P/N 212-010-416-101 Gimbal Ring:

    TB SU-15-08
    Page 3 of 5
    ECCN EAR99
    Approved for Public Release
    CAUTION

    In the following steps, ensure that no sealant is allowed to


    enter bearings.

    (1) Apply sealant (C-352) sparingly to the faying surfaces of the bearing and
    liner assemblies and shims.

    (2) Apply sealant (C-299) sparingly to the faying surfaces of the P/N NAS6203-
    1H Bolts.

    -NOTE-

    Refer to Figure 1, notes 1 and 2. Install P/N 204-011-457-


    003 Washer with chamfer toward bolt head and, when
    installed under nut, install with chamfer toward lug.

    c. Install bearing liner assemblies and shims, and torque bolts while sealant
    remains wet.

    d. Reassemble remainder of Swashplate and Support Assembly as required.

    4. Ensure P/N 212-010-416-101 Gimbal Ring Assembly historical record card (HRC)
    shows the airworthiness life as 9,000 hours.

    5. Revise swashplate and support assembly historical records to show installation of


    the 212-010-416-101 gimbal ring and its retirement life.

    8. Make an entry in helicopter historical service records indicating compliance with this
    Technical Bulletin.

    7. Refer to BHT-205A1-CR&O for P/N 212-010-416-101 Gimbal Ring Assembly


    damage repair limits and repair procedures. Damage limits noted in TM 55-1520-
    210-23-1, DMWR 55-1520-210, and/or DMWR 55-1615-221 apply only to P/N 204-
    010-404-003.

    8. Refer to Figure 1 for P/N 212-010-416-101 Gimbal Ring Assembly detail parts and
    attaching hardware.

    TB SU-15-08
    Page 4 of 5
    ECCN EAR99
    Approved for Public Release
    TB SU-15-08
    Page 5 of 5
    ECCN EAR99
    Approved for Public Release

    You might also like