Scribd Logo
Upload

Welcome to Scribd!

  • 2 views

    Delco 1 Bar MAP Sensor

    Uploaded by

    farmtuningecu

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Flag for inappropriate content

    Delco 1 Bar MAP Sensor

    Uploaded by

    farmtuningecu
    2 views1 page

    Original Title

    53001 Delco 1 Bar MAP sensor

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Report this Document

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Flag for inappropriate content
    Download as pdf or txt
    2 views1 page

    Delco 1 Bar MAP Sensor

    Uploaded by

    farmtuningecu

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Flag for inappropriate content
    Download as pdf or txt
    of 1

    DATASHEET PART 53001

    DELCO 1 BAR MAP SENSOR

    CALIBRATION
    Manual Calibration
    • 0.247 V = 15 kPa
    • 4.853 V = 102 kPa

    Using M1 Tune
    For M130, M150, M170, M190, M141, M142, M181 and M182.
    Use GM Delphi 1 Bar 1.0 from drop down list or use manual
    calibration.

    This One Bar Manifold Absolute Pressure Sensor is Using the ECU Manager
    suitable for engine load measurements on naturally For M84, M400, M600, M800 and M880.

    aspirated engines. Use predefined calibrations:


    • kPa: #12 Pres (kPa) Delco 100 kPa
    SPECIFICATIONS • PSI: #18 Pres (PSI) Delco 100 kPa

    The Delco pressure sensor is an analogue sensor with a 0 V to Using the Display/Logger Manager
    5 V output. The sensor signal can be wired to Analogue
    For C125, C185, C127, C187, SDL3, ADL3, CDL3
    Voltage (AV) input on compatible devices, see the Pin Table.
    Use the predefined calibration: Delco 1Bar MAP

    COMPATIBILITY
    Suitable for use with:
    • M1 Series ECUs
    • M84 ECU
    • Hundred Series ECUs
    • All MoTeC Data Loggers

    Connector
    MoTeC connector part number: 64002

    ECU AVAILABLE SIGNAL PINS

    M84 M400, M600, M800 M880 M130* M150* M170* M190* M141/M142* M181/M182*
    A15, A17, A14, A15, A16, A17, 6, 7, A14, A15, C14, C15, C16, A6, A7, A12, C42, C36, C35, C14, C15, C16, C42, C36, C35,
    A25, B22 A25, B20, B21, B22 12, 18, A16, A17, C17, C25, D20, A18, A26, C28, C29, C11, C17, C25, D20, C28, C29, C11,
    26, 35, A25, B20, D21, D22, A35, A36, C12, C6, C13, D21, D22, B10, C12, C6, C13, C7,
    36, 44 B21, B22 B10, B11, B12 A44 C7, A13, A35, B11, B12, B16, A13, A35, A34,
    A34, A41, A27, B17, B18, A3, A4, A41, A27, A28,
    A28, A29, A38 A5 A29, A38

    *Availability of some M1 series ECU pins may be limited depending on channel assignments for specific firmware Packages.

    © MoTeC Published 17 July 2018 Check for the latest version at www.motec.com 1

    You might also like