Professional Documents
Culture Documents
HP LaserJet 3200 Service Manual
HP LaserJet 3200 Service Manual
service manual
LaserJet all-in-one
Service manual
Copyright Information 2000 Hewlett-Packard Company All Rights Reserved. Reproduction, adaptations, or translation without prior written permission is prohibited except as allowed under copyright laws. Part number C7052-90923 First edition, September 2000 Printed in USA
Trademark Credits Microsoft, Windows, and MSDOS are U.S. registered trademarks of Microsoft Corporation. ENERGY STAR is a U.S. registered service mark of the U.S. EPA. All other products mentioned herein may be trademarks of their respective companies.
Use only a grounded electrical outlet when connecting the HP LaserJet 3200 product to a power source. If you dont know whether the outlet is grounded, check with a qualified electrician. Do not touch the contacts on the end of the telephone cord or any of the sockets on the HP LaserJet 3200 product. Replace damaged cords immediately. Never install telephone wiring during a lightning storm. Unplug this product from wall outlets and telephone jacks before cleaning. Do not install or use this product near water or when you are wet. Install the product securely on a stable surface. Install the product in a protected location where no one can step on or trip over the line cord and the line cord will not be damaged. If the product does not operate normally, see the online user guide. Refer all servicing questions to qualified personnel.
Warranty The information contained in this document is subject to change without notice. Hewlett-Packard makes no warranty of any kind with respect to this information. HEWLETT-PACKARD SPECIFICALLY DISCLAIMS THE IMPLIED WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Hewlett-Packard shall not be liable for any direct, indirect, incidental, consequential, or other damage alleged in connection with the furnishing or use of this information. NOTICE TO U.S. GOVERNMENT USERS: RESTRICTED RIGHTS COMMERCIAL COMPUTER SOFTWARE: Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (c) (1)(ii) of the Rights in Technical Data Clause at DFARS 52.227-7013.
8 9
Safety Information WARNING! Potential Shock Hazard Always follow basic safety precautions when using this product to reduce risk of injury from fire or electric shock. 1 Read and understand all instructions in the user guide. Observe all warnings and instructions marked on the product. 11 10
Information regarding FCC Class B, Parts 15 and 68 requirements can be found in the user guide.
Contents
1 Product information
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hardware description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Firmware description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Product specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Model and serial numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Product overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Warranty statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hewlett-Packard limited warranty statement . . . . . . . . . . . . . . . . . . . . . . . . . . . Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Toner cartridge information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Additional product stewardship . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Environmental conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 14 15 16 19 20 23 23 25 26 27 27
3 Maintenance
Life expectancies of consumables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cleaning and maintaining the equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cleaning the product . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cleaning the scanner path . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Recalibrating the scanner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . User-replaceable parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 53 54 57 59 60
EN
4 Operational overview
Basic functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Optical system. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Formatter system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Draft mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MEt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Enhanced I/O . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page Protect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PJL Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Printer functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Engine control unit/power system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Image formation system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Printer paper feed system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Basic sequence of operation (formatter-to-printer) . . . . . . . . . . . . . . . . . . . . . . . . . . 62 63 65 66 66 66 66 67 67 68 69 74 77 82
4 Chapter - Contents
EN
Pickup roller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Paper-pickup assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Kick plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Separation pad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Bottom assemblies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Formatter pan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Formatter and LIU. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ECU pan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Paper-feed assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6 Troubleshooting
Basic troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Errors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Image formation troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Checking the toner cartridge. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Solving image-quality problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Solving paper feed problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Functional checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Engine test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Half-self-test functional check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Drum rotation functional check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Heating element check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . High-voltage power supply check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Paper path check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Service mode functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Secondary service menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Developers menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Diagnostic mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . NVRAM init . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PJL software commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Troubleshooting tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Internal reports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Printing all fax reports at once . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . T.30 protocol trace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Repetitive image defect ruler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Document scanner recalibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Main wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Locations of connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146 149 156 156 157 164 167 167 168 169 170 171 173 174 174 175 176 178 178 181 181 182 183 191 192 194 196
How to use the parts lists and diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Common hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Assembly locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Covers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Trays and bins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . External covers and panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Document scanner assemblies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Document scanner assemblies. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Document feeder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Upper guide assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Internal assemblies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Internal components (1 of 4). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Internal components (2 of 4). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Internal components (3 of 4). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Internal components (4 of 4). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Feeder assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Electrical components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Alphabetical parts list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Numerical parts list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
203 204 205 206 207 209 210 211 213 215 216 217 219 221 223 225 227 228 233
Index
6 Chapter - Contents
EN
Figures
Figure 1. Figure 2. Figure 3. Figure 4. Figure 5. Figure 6. Figure 7. Figure 8. Figure 9. Figure 10. Figure 11. Figure 12. Figure 13. Figure 14. Figure 15. Figure 16. Figure 17. Figure 18. Figure 19. Figure 20. Figure 21. Figure 22. Figure 23. Figure 24. Figure 25. Figure 26. Figure 27. Figure 28. Figure 29. Figure 30. Figure 31. Figure 32. Figure 33. Figure 34. Figure 35. Figure 36. Figure 37. Figure 38. Figure 39. Figure 40. Figure 41.
EN
Model and serial number label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Front and side view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Top view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Rear view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Product dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Basic configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 Document scanner path . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 Printer unit functional block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 68 ECU loads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 Overview of laser/scanner operation . . . . . . . . . . . . . . . . . . . . . . . . . . 71 High-voltage power supply circuit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 Image formation block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 Printer path . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78 Solenoid, photosensors, and switches . . . . . . . . . . . . . . . . . . . . . . . . . 80 General timing diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83 DIMMs removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89 Back cover removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 Right side cover removal (1 of 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91 Right side cover removal (2 of 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92 Internal paper guide removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94 Top cover removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95 Printer door removal (1 of 4). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96 Printer door removal (2 of 4). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97 Printer door removal (3 of 4). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98 Printer door removal (4 of 4). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99 Document scanner assembly removal (1 of 3) . . . . . . . . . . . . . . . . . . 100 Document scanner assembly removal (2 of 3) . . . . . . . . . . . . . . . . . . 101 Document scanner assembly removal (3 of 3) . . . . . . . . . . . . . . . . . . 102 Contact image sensor removal (1 of 2) . . . . . . . . . . . . . . . . . . . . . . . 103 Contact image sensor removal (2 of 2) . . . . . . . . . . . . . . . . . . . . . . . 104 Document scanner pickup roller removal . . . . . . . . . . . . . . . . . . . . . . 105 Document scanner separation pad removal. . . . . . . . . . . . . . . . . . . . 106 Document scanner motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107 Upper guide assembly removal (1 of 4) . . . . . . . . . . . . . . . . . . . . . . . 108 Upper guide assembly removal (2 of 4) . . . . . . . . . . . . . . . . . . . . . . . 109 Upper guide assembly removal (3 of 4) . . . . . . . . . . . . . . . . . . . . . . . 110 Upper guide assembly removal (4 of 4) . . . . . . . . . . . . . . . . . . . . . . . 111 Control panel/scanner board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112 Laser/scanner assembly removal. . . . . . . . . . . . . . . . . . . . . . . . . . . . 113 Output roller removal (1 of 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114 Figures 7
Figure 42. Figure 43. Figure 44. Figure 45. Figure 46. Figure 47. Figure 48. Figure 49. Figure 50. Figure 51. Figure 52. Figure 53. Figure 54. Figure 55. Figure 56. Figure 57. Figure 58. Figure 59. Figure 60. Figure 61. Figure 62. Figure 63. Figure 64. Figure 65. Figure 66. Figure 67. Figure 68. Figure 69. Figure 70. Figure 71. Figure 72. Figure 73. Figure 74. Figure 75. Figure 76. Figure 77. Figure 78. Figure 79. Figure 80. Figure 81. Figure 82. Figure 83. Figure 84. Figure 85. Figure 86. Figure 87. Figure 88.
Output roller removal (2 of 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Delivery assembly removal (1 of 2) . . . . . . . . . . . . . . . . . . . . . . . . . . Delivery assembly removal (2 of 2) . . . . . . . . . . . . . . . . . . . . . . . . . . Paper exit-sensor flag removal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fusing element removal (1 of 4). . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fusing element metal clips reinstallation . . . . . . . . . . . . . . . . . . . . . . Fusing element removal (2 of 4). . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fusing element removal (3 of 4). . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fusing element removal (4 of 4). . . . . . . . . . . . . . . . . . . . . . . . . . . . . Gear train motor (1 of 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Gear train motor (2 of 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Gear train motor (3 of 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Solenoid removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pressure roller removal (1 of 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pressure roller removal (2 of 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Transfer roller removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Paper-pickup assembly removal (1 of 2) . . . . . . . . . . . . . . . . . . . . . . Paper-pickup assembly removal (2 of 2) . . . . . . . . . . . . . . . . . . . . . . Kick plate removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Separation pad removal (1 of 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Separation pad removal (2 of 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Formatter pan removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Formatter and LIU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ECU pan removal (1 of 2). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ECU pan removal (2 of 2). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Paper-feed assembly removal (1 of 3) . . . . . . . . . . . . . . . . . . . . . . . . Paper-feed assembly removal (2 of 3) . . . . . . . . . . . . . . . . . . . . . . . . Paper-feed assembly removal (3 of 3) . . . . . . . . . . . . . . . . . . . . . . . . Engine test switch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Toner cartridge high-voltage connection points . . . . . . . . . . . . . . . . . High-voltage connector assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . Overriding SW301 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . NVRAM PJL factory variables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Example of a successfully sent fax. . . . . . . . . . . . . . . . . . . . . . . . . . . Example of a successfully received fax . . . . . . . . . . . . . . . . . . . . . . . Repetitive image defect ruler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Main wiring (1 of 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Main wiring (2 of 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Locations of connectors (1 of 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Locations of connectors (2 of 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Locations of connectors (3 of 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Assembly locations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Trays and bins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . External covers and panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Document scanner assemblies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Document feeder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Upper guide assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 132 133 134 135 136 137 138 139 140 141 142 143 167 171 172 173 179 189 190 191 194 195 196 197 197 205 206 208 210 212 214
EN
8 Chapter - Figures
Figure 89. Figure 90. Figure 91. Figure 92. Figure 93. Figure 94.
Internal components (1 of 4). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Internal components (2 of 4). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Internal components (3 of 4). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Internal components (4 of 4). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Feeder assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Electrical components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
EN
10 Chapter - Figures
EN
Tables
Table 1. Table 2. Table 3. Table 4. Table 5. Table 6. Table 7. Table 8. Table 9. Table 10. Table 11. Table 12. Table 13. Table 14. Table 15. Table 16. Table 17. Table 18. Table 19. Table 20. Table 21. Table 22. Table 23. Table 24. Table 25. Table 26. Table 27. Table 28. Table 29. Table 30. Table 31. Table 32. Table 33. Table 34. Table 35. Physical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Environmental specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Power specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Operating acoustical emissions (per ISO 9296) specifications . . . . . . 18 Skew specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Control panel error messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Media types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Life expectancies of consumables . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 Basic troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146 Control panel error messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149 Communication errors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155 Solving image-quality problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157 Solving paper feed problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164 Diagnostic mode key sequences . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176 Fax phase sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185 Appropriate responses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 186 Fax abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 187 Authorized parts resellers in the United States . . . . . . . . . . . . . . . . . 200 Technical support Web sites . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 201 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 202 Common fasteners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 204 Trays and bins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 207 External covers and panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 209 Document scanner assemblies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 211 Document feeder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 213 Upper guide assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 215 Internal components (1 of 4). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 217 Internal components (2 of 4). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 219 Internal components (3 of 4). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 221 Internal components (4 of 4). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 223 Feeder assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 225 Electrical components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 227 Alphabetical parts list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 228 Numerical parts list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 233
EN
Tables 11
12 Chapter - Tables
EN
Product information
Chapter contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Hardware description . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Firmware description . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Product specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Model and serial numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Product overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Warranty statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Declaration of Conformity. . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Toner cartridge information . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Additional product stewardship . . . . . . . . . . . . . . . . . . . . . . . 27 Environmental conformity . . . . . . . . . . . . . . . . . . . . . . . 27
EN
Chapter contents 13
Introduction
The HP LaserJet 3200 product is a powerful business tool with the capabilities of a full range of office equipment. With the HP LaserJet 3200 product, you can:
l l
PrintPrint documents easily with the laser quality you have come to expect from an HP LaserJet printer. FaxUse the HP LaserJet 3200 product as a standalone fax machine to send and receive faxes, as well as perform advanced tasks such as forwarding faxes to other locations. Use the software to send faxes from and receive them to your computer. CopyMake superior laser-quality copies. You can make up to 99 copies of a 30-page original. You can also enlarge, reduce, adjust contrast, and collate. ScanScan important documents to create electronic files. Use softwareUse the software to print, fax, copy, or scan. Also use the software to store and organize scanned documents.
l l
Hardware description
The HP LaserJet 3200 product provides 1200 dot-per-inch (dpi) printing, plus scanning capabilities. The scanner scans at 600 dpi/ 24 bits per pixel (bpp) and contains a document feeder that holds up to 30 pages. The HP LaserJet 3200 product prints nine pages per minute (ppm). It provides an excellent Windows printing solution, ease of use, and higher performance. With 1200 dpi printing resolution, the HP LaserJet 3200 product has exceptional text and graphics print quality. The simplified control panel and improved paper handling make this product very simple to use. There is one main media input tray with a 125-sheet capacity for continuous, multiple-page printing. Manual, single-sheet printing is possible through the single-sheet input tray. Both trays are centerjustified for all supported paper sizes. The output tray holds up to 100 sheets. The HP LaserJet 3200 product has a very fast first-page-out, at less than eighteen seconds. The formatter board contains 12 MB of ROM, 8 MB of RAM, and a 32-bit MCF5202 chip. There is one DIMM slot available for DIMM expansion (supporting an 8 MB, 16 MB, 32 MB, or
EN
64 MB DIMM). The HP LaserJet 3200 product engine has a 1,000 average (10,000 peak) page-per-month duty cycle and has no fan. The toner life for the HP LaserJet 3200 product is 2,500 pages.
Firmware description
The firmware in the HP LaserJet 3200 product includes:
l l l l l
Enhanced PCL 6 with status readback 45 fonts in Intellifont format, plus Cyrillic Full-page 600 dpi bitmap Pixel placement, mosaic characters Memory Enhancement technology (MEt) with hardware compression/decompression
The HP LaserJet 3200 product firmware also has REt and EconoMode functionality. Scan capability includes 600 dpi and 24-bit color.
EN
Introduction 15
Product specifications
Table 1. Physical specifications Category
Height Depth Width Weight (cartridge installed)
Specification
272 mm (10.71 inches) without supports attached; 404 mm (15.91 inches) with supports attached 390 mm (15.36 inches) without supports attached; 598 mm (23.55 inches) with supports attached 384 mm (15.12 inches) 10.6 kilograms (23.37 pounds)
Specification
Printer plugged into an AC outlet: l Temperature: 15 to 32.5 degrees Celsius (C); 59 to 90.5 degrees Fahrenheit (F) l Humidity: 20 to 80 percent relative humidity (no condensation) Printer unplugged from an AC outlet: l Temperature: 0 to 40 degrees C (32 to 104 degrees F) l Humidity: 10 to 90 percent relative humidity (no condensation)
Storage environment
EN
Specification
100 to 120 Volts alternating current (Vac), 50/60 Hz (2%; 127 Vac, 60 Hz NOM 200 watts
Specification
1200 dpi 600 dpi optical, with 256 levels of gray and 24-bit color Standard: 203 by 98 dpi Fine: 203 by 196 dpi Superfine: 300 by 300 dpi (no halftone) Photo: 300 by 300 dpi (halftone enabled) 9 ppm 9 ppm
EN
Product specifications 17
Specification
6.3 bels (B) 57 decibels (dB) 48 dB
Specification
0.6% (1.5 mm over 250 mm in length) 0.64% (1.2 mm over 190 mm in width) 1.2%
EN
Figure 1.
EN
Product overview
4 3
1 Figure 2. Front and side view 1 2 3 4 5 Front paper path door Document output slot Control panel/document release door Printer door Printer door release latches
EN
8 7 6 9
10 Figure 3. Top view 6 7 8 9 Document feeder tray Paper output bin Single-sheet input tray Paper input tray
EN
Product overview 21
13
14
15 12 17 16
Figure 4.
Rear view 11 Phone line connectors 12 Power cable connector 13 Model and serial number label 14 Memory door 15 Parallel cable connector 16 USB connector
EN
Warranty statement
This warranty gives specific legal rights. There may also be other rights which vary from area to area. See the user guide for further warranty information or see the warranty card included with the printer.
4 5
HP MAKES NO OTHER EXPRESS WARRANTY OR CONDITION WHETHER WRITTEN OR ORAL. TO THE EXTENT ALLOWED BY LOCAL LAW, ANY IMPLIED WARRANTY OR CONDITION OR MERCHANTABILITY, SATISFACTORY QUALITY, OR FITNESS FOR A PARTICULAR
EN
Warranty statement 23
PURPOSE IS LIMITED TO THE DURATION OF THE EXPRESS WARRANTY SET FORTH ABOVE. Some countries, states or provinces do not allow limitations on the duration of an implied warranty, so the above limitation or exclusion might not apply to you. This warranty gives you specific legal rights and you might also have other rights that vary from country to country, state to state, or province to province. 7 TO THE EXTENT ALLOWED BY LOCAL LAW, THE REMEDIES IN THIS WARRANTY STATEMENT ARE YOUR SOLE AND EXCLUSIVE REMEDIES. EXCEPT AS INDICATED ABOVE, IN NO EVENT WILL HP OR ITS SUPPLIERS BE LIABLE FOR LOSS OF DATA OR FOR DIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL (INCLUDING LOST PROFIT OR DATA), OR OTHER DAMAGE, WHETHER BASED IN CONTRACT, TORT, OR OTHERWISE. Some countries, states or provinces do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
EN
Declaration of Conformity
Declaration of Conformity
according to ISO/IEC Guide 22 and EN 45014 Manufacturers Name: Manufacturers Address: declares, that the product Product Name: Model Number: Product Options: HP LaserJet 3200 product C7052A, 7053A, 7055A (Printer/Fax/Scanner/Copier) ALL Hewlett-Packard Company 11311 Chinden Boulevard Boise, Idaho 83714-1021, USA
conforms to the following Product Specifications: Safety: EMC: IEC 950:1991+A1+A2+A3+A4/EN 60950:1992+A1+A2+A3+A4+A11 IEC60825-1:1993+A1/EN 60825-1:1994+A11 Class 1 Laser/LED Product CISPR 22:1997/EN 55022:1998 Class B1 CISPR 24:1997/EN 55024:1998 IEC 61000-3-2:1995/EN61000-3-2:1995 IEC61000-3-3:1994/EN61000-3-3:1995 FCC Title 47 CFR, Part 15 Class B2 / ICES-003, Issue 2 AS / NZS 3548:1995
Supplementary Information: The product herewith complies with the requirements of the Low Voltage Directive 73/23/EEC, the EMC Directive 89/336/EEC, and the R&TTE Directive 1999/5/EC (Annex II) and carries the CE-marking accordingly. 1) 2) The product was tested in a typical configuration with Hewlett-Packard Personal Computer Systems. This Device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. April 18, 2000
EN
Declaration of Conformity 25
Repairs resulting from the use of refilled toner cartridges are not covered under Hewlett-Packard warranty or maintenance contracts. Hewlett-Packard has no control or process to ensure that a refilled toner cartridge functions at the high level of reliability of a new HP LaserJet toner cartridge. Hewlett-Packard also cannot predict the long term reliability effect on the printer from using different toner formulations found in refilled cartridges. The print quality of HP LaserJet toner cartridges influences the customers perception of the printer. Hewlett-Packard has no control over the actual print quality of a refilled toner cartridge.
EN
EN
EN
Chapter contents
Operating environment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Identifying product components . . . . . . . . . . . . . . . . . . . . . . . 31 Control panel lights and keys . . . . . . . . . . . . . . . . . . . . 31 Using the control panel menu structure . . . . . . . . . . . . 33 Control panel error messages . . . . . . . . . . . . . . . . . . . . . . . . 35 Selecting media . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Selecting media to print . . . . . . . . . . . . . . . . . . . . . . . . 43 Selecting media to fax, copy, or scan. . . . . . . . . . . . . . 44 Loading media . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Loading media to fax, copy, or scan. . . . . . . . . . . . . . . 45 Loading media to be printed . . . . . . . . . . . . . . . . . . . . . 48 Selecting the output path . . . . . . . . . . . . . . . . . . . . . . . 50
EN
Chapter contents 29
Operating environment
Place the product on a sturdy, level surface in a well-ventilated area that meets the following environmental requirements:
l l l l
temperature: 15 to 32.5 degrees C (59 to 90.5 degrees F) humidity: 20 to 80 percent relative humidity (no condensation) away from direct sunlight, open flames, and ammonia fumes sufficient space around the product to allow for proper access and ventilation, as shown in the figure below:
Figure 5.
Product dimensions
2 1
10
6 19 18 17 16
7 11
12 15 14 13
Figure 6.
Control panel 1 2 Error lightwhen solid, indicates an error condition. Ready lightwhen solid, indicates the product is ready and has no error conditions; when blinking, indicates that the product is processing a job. Control panel displaydisplays messages or Menu settings. Enter/Menuuse to gain access to the Menu, save a selection, or go down one level in the Menu settings. Back spaceuse to go up one level in the Menu settings or to backspace when typing text. < (back arrow)use to scroll back through items at the same Menu level, move back through text. > (forward arrow)use to scroll forward through items at the same Menu level; also use to insert a space when typing text or scroll forward.
3 4 5 6 7
EN
8 9
Stop/Clearstops or clears any action in progress or exits the Menu settings. Scanstarts scanning documents loaded in the document feeder.
10 Copystarts the copy function. 11 One-touch keypaduse the keys on the one-touch keypad to store frequently dialed fax numbers. 12 Fax/Senduse to start sending paper faxes. 13 Volumeuse to adjust the line monitor volume for incoming and outgoing fax connection sounds. 14 Speed-Dialpress this key, plus a one-, two- or three-digit code to fax to previously stored fax numbers. 15 Redial/Pausepress to redial the last fax number or use to insert a pause into a fax number. 16 Numeric keysuse to enter fax numbers. Also use to add letters when typing a name in the fax header or for speed-dials. 17 Reduce/Enlargeuse to adjust the size of the current copy job. 18 Resolutionuse to adjust the resolution, or sharpness, for the current fax or copy job. 19 Contrastuse to adjust the contrast, or difference between light and dark areas, for the current fax or copy job.
EN
EN
Main Menu
Fax job status Fax functions
Submenu
Send fax later Stop receive to PC Reprint last faxes Polling receive Clear stored faxes Time/date Fax header Default quality Default contrast Default collation Default # of copies Default reduce/enlarge Demo page Fax activity log Fax call report Speed dial report Menu structure Configuration report Block fax list PCL font list All fax reports Speed dials Fax send setup Fax receive setup All faxes Default paper size Print density Volume settings Scan calibration Print T.30 trace Restore defaults Cleaning mode
Reports
Fax setup
Common settings
Service
EN
Cause
The product is waiting for you to press a programmed one-touch key or enter a speed-dial code to a group-dial code. The one-touch key or speed-dial code has not been programmed and therefore cannot be added to a group.
Solution
Begin adding fax numbers to the group-dial code. See Programming group-dial codes in the online user guide. Press ENTER/MENU to program the one-touch or speeddial. If you want to program a group-dial, press STOP/CLEAR and use the control panel menu to create a new group. Press STOP/CLEAR if you do not want to program the one-touch or speed-dial. Disconnect the power cable from the product, wait at least 30 seconds, then reconnect the power cable and wait for the product to initialize. If the message does not clear, see chapter 6, Troubleshooting. Disconnect the power cable from the product, wait at least 30 seconds, then reconnect the power cable and wait for the product to initialize. If the message does not clear, see chapter 6, Troubleshooting. Disconnect the power cable from the product, wait at least 30 seconds, then reconnect the power cable and wait for the product to initialize. If the message does not clear, see chapter 6, Troubleshooting. Disconnect the power cable from the product, wait at least 30 seconds, then reconnect the power cable and wait for the product to initialize. If the message does not clear, see chapter 6, Troubleshooting.
50 FUSER ERROR
51 LASER ERROR
52 SCANNER ERROR
53 PRINTER ERROR
EN
Cause
The product has experienced an internal hardware error.
Solution
Disconnect the power cable from the product, wait at least 30 seconds, then reconnect the power cable and wait for the product to initialize. If the message does not clear, see chapter 6, Troubleshooting. Disconnect the power cable from the product, wait at least 30 seconds, then reconnect the power cable and wait for the product to initialize. If the message does not clear, see chapter 6, Troubleshooting. Disconnect the power cable from the product, wait at least 30 seconds, then reconnect the power cable and wait for the product to initialize. If the message does not clear, see chapter 6, Troubleshooting. Disconnect the power cable from the product, wait at least 30 seconds, then reconnect the power cable and wait for the product to initialize. If the message does not clear, see chapter 6, Troubleshooting. Disconnect the power cable from the product, wait at least 30 seconds, then reconnect the power cable and wait for the product to initialize. If the message does not clear, see chapter 6, Troubleshooting. Disconnect the power cable from the product, wait at least 30 seconds, then reconnect the power cable and wait for the product to initialize. If the message does not clear, see chapter 6, Troubleshooting. Pull the document release door open, remove the jammed item, and close the door. Then, clear the items in the document feeder tray and start over.
55 DC CONTROLLER ERROR
79 SERVICE (####)
80 SERVICE (####)
81 SERVICE (####)
The STOP/CLEAR key was pressed to cancel the current job while pages were feeding from the document feeder. The cancel process will not automatically clear the document feeder.
EN
Solution
Pull the document release door open, remove the jammed item, and close the door. Then, clear the items in the document feeder tray and start over.
Pull the document release door open, remove the jammed item, and close the door. Then, clear the items in the document feeder tray and start over. Allow the product to retry sending the fax. Unplug the product telephone cord from the wall, plug in a telephone, and try making a call. Plug the product phone cord into a jack for another phone line. See chapter 6, Troubleshooting. Continue completing the collated copy job. Wait for the product to finish the current job. Press ENTER/MENU to resume the job. Open the document release door, clear the jam, close the document release door, and reload the paper into the document feeder tray. Remove and reload the media into the document feeder tray.
COMMUNICATION ERROR
The product does not have enough memory to complete the collated copy job. The product is currently in use. There was an internal error in the product. A piece of media is jammed in the document feeder tray.
DEVICE BUSY. TRY AGAIN LATER DEVICE ERROR. PRESS [ENTER] TO RESUME DOCUMENT FEEDER JAM
EN
Cause
Attempts to redial a fax number failed or the redial on no answer option was turned off.
Solution
Call the recipient to ensure that fax machine is on and ready. Check that you are dialing the correct fax number. Check that the redial option is enabled. Unplug the telephone cord from both the product and the wall and replug the cord. Unplug the product telephone cord from the wall, plug in a telephone, and try making a call. Plug the product phone cord into a jack for another phone line. See chapter 6, Troubleshooting. Allow the product to retry sending the fax. Call the recipient to ensure that fax machine is on and ready. Check that you are dialing the correct fax number. Check that the redial on no answer option is enabled. Unplug the product telephone cord from the wall, plug in a telephone, and try making a call. Plug the product phone cord into a jack for another phone line. See chapter 6, Troubleshooting. Print all of the faxes and have the sender resend the fax. Cancel all fax jobs or clear the faxes from memory (see Clearing faxes from memory in the online user guide). Print all received faxes or wait until all pending faxes are sent. Cancel all fax jobs or clear the faxes from memory (see Clearing faxes from memory in the online user guide).
You tried to send a fax, but the receiving fax line did not answer. The product attempts to redial after a few minutes.
During the fax transmission, the product ran out of memory. Only the pages that fit into memory will be printed.
During the fax job, the memory filled. All pages of the fax have to be in memory for a fax job to work correctly. Only the pages that fit into memory were sent.
EN
Cause
An error occurred while trying to receive a fax.
Solution
Ask the sender to resend the fax. Try faxing back to sender or another fax machine. Check that the telephone cord is securely connected by unplugging and replugging the cord. Check for a dial tone on the phone line by pressing FAX/ SEND. Make sure the phone is working by disconnecting the product, plugging in a telephone to the phone line, and making a voice call. Connect the product to a different phone line. Try resending the fax. Try faxing to another fax number. Check that the telephone cord is securely connected by unplugging and replugging the cord. Check for a dial tone on the phone line by pressing FAX/ SEND. Make sure the phone is working by disconnecting the product, plugging in a telephone to the phone line, and making a voice call. Connect the product to a different phone line. Enter one-touch keys (programmed as an individual speed dial) or speed-dial codes to a group-dial Resend to the ad hoc group using less fax numbers. Wait for the product to finish the cleaning cycle. The message will clear when the cycle is finished. Reenter the date. Reenter the time. Reenter any desired job settings.
The speed-dial code you entered is programmed for a group. Adding a group-dial to another group-dial is not allowed. The maximum number of fax numbers that can be added to an ad hoc group is 20. The product is running an internal cleaning cycle. An invalid date was entered, such as June 35. An invalid time was entered, such as 25:99 PM. The product has cleared job settings.
GROUP IS FULL. [FAX] TO START IN CLEANING MODE. PLEASE WAIT 1-3 MIN. INVALID DATE INVALID TIME JOB SETTINGS CLEARED
EN
Cause
The product completed making one copy. The remaining copies have been canceled because of low product memory.
The product memory has been almost completely filled. The product could not detect a dial tone.
NO DOCUMENT SENT
The fax forwarding setting is on and the product unsuccessfully received a fax because of low memory or some other reason. The product deleted the incomplete received data before attempting to forward the deleted data. The product answered the incoming call but could not determine that the caller was a fax machine.
NO FAX DETECTED
Allow the product to retry sending the fax. Unplug the product telephone cord from the wall, plug in a telephone, and try making a call. Plug the product phone cord into a jack for another phone line. See chapter 6, Troubleshooting. Receive a fax before attempting to use this option. Wait until the current job is finished before starting a new job.
NO FAX PAGES IN MEMORY TO REPRINT NOT ENOUGH MEMORY. TRY AGAIN LATER
The product attempted to execute Reprint Last Fax when nothing was in memory. There is not enough memory to start a new job.
EN
Cause
The product has detected a power failure and is performing a self-test.
Solution
The product should go back to the ready state on its own. If this message does not go away in a couple of minutes, disconnect the power cable from the product, wait at least 30 seconds, then reconnect the power cable and wait for the product to initialize. Press ENTER/MENU to clear the error. The product should return to the ready state.
The product has detected a power failure and the last update to the fax settings was corrupted. The product is resetting all fax settings to the factory default settings. The product has detected a power failure and is printing all of the faxes that it did not previously print. The product has detected a power failure and has also detected unsent faxes and will try to resend them. The DIMM in the indicated slot has failed. The product has detected that a jam has occurred. The printer door is open or the toner cartridge is not installed properly. The paper input tray is empty.
The product prints all of the received faxes that it did not previously print. Once the faxes are printed, the product will return to the ready state. The product resents the unsent faxes. Once the faxes are sent, the product will return to the ready state. Turn off the product and check the indicated DIMM. Clear the jam. The job should continue to print. If it does not, try reprinting the job. Make sure the printer door is closed. Check the toner cartridge for proper installation. Load media. If media is already loaded, remove it. Check for and remove any jam, and then reload the stack of media in the paper input tray. Reload the paper in the paper input tray and press ENTER/ MENU to continue the job.
POWER OFF. CHECK DIMM #[1-3] PRINTER PAPER JAM CLEAR PAPER PATH PRINTER DOOR OPEN OR NO TONER CARTRIDGE PRINTER PAPER TRAY IS EMPTY. ADD PAPER
EN
Cause
The fax line to which you were sending a fax was busy. The product has cancelled sending the fax.
Solution
Call the recipient to ensure that fax machine is on and ready. Check that you are dialing the correct fax number. Check that the redial on busy option is enabled. Press and hold STOP/CLEAR for seven seconds to check for a dial tone. Unplug the product telephone cord from the wall, plug in a telephone, and try making a call. Plug the product phone cord into a jack for another phone line. See chapter 6, Troubleshooting. Allow the product to retry sending the fax. Call the recipient to ensure that fax machine is on and ready. Check that you are dialing the correct fax number. Unplug the product telephone cord from the wall, plug in a telephone, and try making a call. Plug the product phone cord into a jack for another phone line. See chapter 6, Troubleshooting. Wait until the PC scan has finished, or cancel the scan from the computer software, or press STOP/CLEAR. Check the connection cable and try the scan again.
The fax line to which you were sending a fax was busy. The product automatically redials the busy number. (See Changing how the product redials in the online user guide.)
EN
Selecting media
Selecting media to print
You can use paper with up to 100% recycled fiber content if it meets HPs specifications. To order HP paper or the Print Media Guide for HP LaserJet printers, see Ordering parts and supplies on page 200. Highly textured stock might not print evenly. Very glossy papers might jam or repel toner. Multipart forms can wrinkle or get jammed in the product. And paper in poor condition, such as paper with tears, wrinkles, or bent edges, can jam. Avoid envelopes that have a very slick finish, ones that have self-stick adhesives, or those with clasps or windows. Also avoid envelopes with thick, irregular, or curled edges, or areas that are wrinkled, torn, or otherwise damaged. Use a sturdy envelope of approximately 16- to 27-pound (7.25 to 12.25 kg) weight. Use tightly constructed envelopes and make sure the folds are sharply creased. The paper input tray can hold up to 125 sheets of 20 lb (75 g/m2) print media. The single-sheet input tray is designed for one sheet. Both can be adjusted to hold media measuring from 3 by 5 inches (76.2 by 127 mm) to 8.5 by 14 inches (216 by 356 mm). This includes, but is not limited to, the following paper and envelope sizes: Table 8. Media types Paper type
Letter Legal Executive A4 COM10 Envelopes DL Envelopes C5 Envelopes B5 Envelopes Monarch Envelopes Other custom size media
Metric
216 by 279 mm 216 by 356 mm 184 by 267 mm 210 by 297 mm 105 by 241 mm 110 by 220 mm 162 by 229 mm 176 by 250 mm 98.5 by 190.5 mm custom
English
8.5 by 11 in 8.5 by 14 in 7.25 by 10.5 in 8.25 by 11.75 in 4.125 by 9.5 in 4.33 by 8.67 in 6.4 by 9 in 6.9 by 9.85 in 3.875 by 7.5 in custom
EN
Selecting media 43
Remove self-stick notes. Remove staples and paper clips. Straighten any curls or wrinkles in documents before putting them into the document feeder tray. Do not insert any document with glue, correction fluid, or wet ink on it. Do not insert gum-backed paper or labels. Place documents with tears, perforations, or punch holes in a carrier sheet, which you can buy or make. (See To load special items on page 46.) Avoid multiple-copy forms.
EN
Loading media
The following sections explain how to load media for sending and receiving faxes, copying, scanning, and printing.
EN
Loading media 45
Do one of the following: Place the item in a carrier sheet. You can buy a carrier sheet, or you can make one by taping a transparency and piece of paper together along one of the short sides. Insert the item to be faxed, copied, or scanned into the carrier, and insert the carrier into the document feeder tray, taped edge first. - Or -
Using clear tape, tape the leading and trailing edges of the item to a sheet of letter- or A4-size paper. If the item is not square or rectangular, tape all edges of the item to the paper. - Or -
If you have use of a full-size copier, copy the item first and then send the copy through the scanner. Adjust the guides in the document feeder tray to fit the size of the item you are loading.
EN
Locate the special media lever (see figure 3 on page 21) on the top edge of the control panel and move it to the right. The special media lever opens the document feeder mechanism, allowing you to feed thick items, one at a time, into the document scanner.
Note Move the special media lever back to the left after special items have been fed. A stack of regular pages sent with the lever to the right feed in multiples and cause jams.
CAUTION Do not move the lever after the product has begun sending the page. 4 Load only one sheet at a time, leading edge first, face down, into the document feeder tray.
Note If you are loading a business card, load it long edge first.
EN
Loading media 47
2 2
Note When adding media to an existing stack in the paper input tray, always remove the existing media and realign it with the new media before loading to reduce multiple feeds or jams.
Note If you have loaded special media, make sure to choose the lower paper output path. See To select the output path on page 50 3 Readjust the guides to center the stack.
EN
2 3
Note If you have loaded special media, make sure to choose the lower paper output path. See To select the output path on page 50.
EN
Loading media 49
To use the paper output bin, make sure that the front paper path door is closed. - Or -
To use the front paper output slot, open the front paper path door. All printed media coming out of the front paper output slot will be in reverse order. If you open the front paper path door and media does not go through the front paper output slot, make sure the front paper path door is all the way open.
Note Keep the area in front of the front paper output slot clear so that media can easily exit the slot.
EN
Maintenance
Chapter contents
Life expectancies of consumables . . . . . . . . . . . . . . . . . . . . . 52 Cleaning and maintaining the equipment . . . . . . . . . . . . . . . . 53 Cleaning the product . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 Cleaning the scanner path . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 Recalibrating the scanner . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 User-replaceable parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
EN
Chapter contents 51
Printer transfer roller Printer pickup roller Printer separation pad Printer subpads Fusing element Pressure roller
Document scanner pickup RG5-5401-000CN roller assembly Document scanner separation pad kit Document scanner feed roller and document scanner delivery roller RY7-5055-000CN RG5-5399-000CN (Document scanner assembly)
* The estimated toner cartridge life is based on letter- or A4-sized paper with an average of 5% toner coverage and a medium density setting. Toner cartridge life can be extended further by conserving toner using draft mode settings.
52 Chapter 3 - Maintenance
EN
Any time a new toner cartridge is installed. After printing approximately 2,500 pages. Whenever print quality problems appear.
Clean the outside of the printer with a water-dampened cloth. Clean the inside with only a dry, lint-free cloth (such as lens tissues). To avoid permanent damage to the toner cartridge, do not use ammonia-based cleaners on or around the HP LaserJet 3200 product. WARNING! When cleaning around the printer door area, avoid touching the heating element. It might be very hot and can cause burns. Do not touch the surface of the transfer roller. Contaminants on the roller can cause print quality problems. Be careful not to touch the glass surface of the image sensor. If you inadvertently touch the glass, clean it according to the instructions on the following pages.
CAUTION
Note
EN
The device displays the message IN CLEANING MODE until this process is completed.
54 Chapter 3 - Maintenance
EN
Note
If toner spills on carpets or upholstery, remove it using a clean cloth dipped in cold water. Hot water can set toner into fabric. Before cleaning the HP LaserJet 3200 product and replacing the pickup roller, disconnect it from the power source.
WARNING!
CAUTION Using ammonia-based cleaners on or around the HP LaserJet 3200 product can cause damage to it. Also, do not touch the long black sponge roller in the bottom. Touching it can reduce the print quality of output. 2 Use the two latches on the printer door to open it. Clean the inside of the HP LaserJet 3200 product with a dry, lint-free cloth. Remove all dust, spilled toner, and particles of paper.
Note Only use a dry, lint-free cloth to remove dust and toner. Using a vacuum or other device to clean inside the product can damage it.
Note If toner gets on your clothing, wipe it off with a dry cloth and wash clothing in cold water. Hot water and the heat of the dryer sets toner into the fabric.
EN
Note If you notice excessive amounts of toner inside the HP LaserJet 3200 product, the toner cartridge might be defective. Use HP LaserJet toner cartridges to ensure high quality printing and to reduce incidents of excessive toner. 4 Locate the light gray pickup roller near the center in the opening and then rotate the bottom of the pickup roller towards the front of the printer.
CAUTION Do not touch the long black sponge roller inside the product. Touching it can reduce the print quality of output. 5 6 Gently pull the pickup roller straight out. Replace the pickup roller with a new roller (part number RG2-4026000CN). Replace the toner cartridge and close the printer door.
7 7
56 Chapter 3 - Maintenance
EN
WARNING! Alcohol is flammable. Keep it away from open flame. Allow the alcohol to dry completely before closing the printer and plugging in the power cord.
CAUTION If you must use alcohol, only use a very small amount. Exposing internal parts to dripping alcohol can damage them. 3 If the long strip of glass opposite the long, white strip is dirty, clean it with a dry cotton swab. If there is still something on the glass strip, dab a swab in a small amount of isopropyl alcohol and gently clean the glass.
EN
Inspect each of the six rollers in the scanner area for dirt or debris. Clean any dirty rollers with a lint-free cloth (such as lens tissues) dampened with a small amount of isopropyl alcohol.
CAUTION Do not spray alcohol or any other liquid directly into the HP LaserJet 3200 product. Doing so can damage the product.
CAUTION As much as possible, avoid touching the white strip and glass strip with alcohol. 5 Near the top, inside edge of the document release door, inspect the two pressure feet and pad for dirt or debris. If they are dirty, clean them with a lint-free cloth sprayed with a small amount of alcohol. Using a dry, lint-free cloth, wipe rollers, pads, and feet in a side-toside motion to remove loosened dirt. After alcohol inside the scanner area has dried completely, close the document release door.
Every time you clean the scanner path, you should recalibrate the scanner. See Recalibrating the scanner on page 59.
58 Chapter 3 - Maintenance
EN
2 7 3 4
6 7
EN
User-replaceable parts
End-users can replace the printer pickup roller, printer separation pad, and document scanner separation pad when the parts near the end of their life expectancies or when users notice an increase in misfeeds in the printer path or document scanner path. Instructions for replacing the printer pickup roller and document scanner appear in chapter 5, Removal and replacement.
l l
For instructions about replacing the printer pickup roller, see Pickup roller on page 131. For instructions about replacing the document scanner separation pad, see Document scanner separation pad on page 106.
Instructions for installing a new printer separation pad are contained with the pad itself. When you receive a new separation pad (part number RF5-2886-000CN), you also receive an HP Separation Pad Installation Guide.
60 Chapter 3 - Maintenance
EN
Operational overview
Chapter contents
Basic functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 Optical system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 Formatter system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 Draft mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 MEt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 Enhanced I/O . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 PJL Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 Page Protect. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 Printer functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 Engine control unit/power system. . . . . . . . . . . . . . . . . 69 Image formation system . . . . . . . . . . . . . . . . . . . . . . . . 74 Printer paper feed system . . . . . . . . . . . . . . . . . . . . . . 77 Basic sequence of operation (formatter-to-printer) . . . . . . . . 82
EN
Chapter contents 61
Basic functions
This chapter presents a functional overview of the HP LaserJet 3200 products processes. The following systems are discussed:
l l l
optical system (document scanner) formatter printer functions ECU (engine controller unit) system/power system image formation system paper-feed system (printer) and document-feed system (document scanner)
The HP LaserJet 3200 product consists of the printer and the document scanner. Operation sequences of the printer are controlled by the ECU. Operation sequences of the document scanner are controlled by the formatter.
Figure 7.
Basic configuration
EN
Optical system
The document scanner system consists of the optical system and document pickup and feed systems. The optical system, also known as the contact image sensor, contains the following:
l l l l
light-emitting diode (LED) array contact glass rod lens array sensor array
The light source has three LEDs (red, green, and blue) and is controlled by the formatter. Light reflected from documents passes through the rod lens array and focuses on the sensor array. The sensor array consists of 5,160 phototransistors: 15 driver circuits amplify the light reception output in units of 344 phototransistors. The image data is converted and sent from the driver circuits to the formatter. The document pickup and feed systems contain a pickup roller, feed roller, and delivery roller, all of which are driven by the document scanner motor (M101).
EN
Optical system 63
Figure 8.
EN
Formatter system
The formatter is responsible for the following:
l l l l l l l
controlling the document scanner formatting and controlling faxes formatting and controlling copies receiving and processing print data from the printer interface monitoring the control panel and relaying printer status information developing and coordinating data placement and timing with the print engine communicating with the host computer through the bidirectional interface
The formatter receives print data from the bidirectional Extended Capabilities Port (ECP) mode interface or USB interface and converts it into a dot image. The ECU synchronizes the image formation system with the paper feed system and signals the formatter to send the print image data. The formatter sends the print image data (dots) in the form of a video signal and the printing process begins.
RAM
l l
One bank of Non-Volatile RAM (NVRAM) stores parameters DRAM provides temporary storage of copy, scan, and print data
EN
Formatter system 65
Control panel
l l l
two front panel status lights control panel keyboard control panel display
Draft mode
Depending on which printer driver is used, selecting draft or EconoMode from the printer driver allows the HP LaserJet 3200 product to use approximately 50% less toner, extending the life of the toner cartridge.
MEt
The Hewlett-Packard Memory Enhancement technology effectively doubles the standard memory through a variety of font and datacompression methods.
Enhanced I/O
The Enhanced I/O feature allows printer memory to be used for storing data received from the host computer. When Enhanced I/O is enabled, you can send more data to the printer in shorter amounts of time, which allows you to return to your application sooner. Enhanced I/O has the following options:
l
Autoallows the printer to use Enhanced I/O memory allocation to increase the speed of data transfer from the host computer to the printer, if necessary. Offuses the minimum amount of printer memory for storing data sent from the host computer.
EN
Page Protect
Page complexity (ruling lines, complex graphics, or dense text) can exceed the printers ability to create the page image fast enough to keep pace with the image formation process. If Page Protect is disabled and a page is too complex, the page might print in parts (for example, the top half on one page and the bottom half on the next page). Some print-data loss is likely in these instances, and the printer will display an error message. Page Protect allows the formatter to create the entire page image in page buffer memory before physically moving the paper through the printer. This process ensures that the entire page will be printed. The default setting is Auto.
PJL Overview
Printer Job Language (PJL) is an integral part of configuration, in addition to the standard Printer Command Language (PCL). With standard ECP cabling, PJL allows the printer to perform functions such as:
l
Two-way communication with the host computer through a bidirectional parallel or USB connection. The printer can tell the host such things as the control panel status. Isolation of print environment settings from one print job to the next. For example, if a print job is sent to the printer in landscape mode, the subsequent print jobs print in landscape only if they are formatted for landscape printing.
EN
Formatter system 67
Printer functions
Printer functions are divided into three groups:
l l l
Figure 9.
EN
Printer engine control paper motion monitoring and control (printing) motor
l l
Printer laser/scanner Power system AC power distribution DC power distribution overvoltage/undervoltage protection high-voltage power distribution
EN
Printer functions 69
Figure 10.
ECU loads
EN
Figure 11.
EN
Printer functions 71
+3.3 Vdc:
Formatter Laser/beam detect circuitry ECU Formatter Photosensors ECU Laser/beam detect circuitry Motor Laser scanner motor Document scanner motor Solenoid Formatter High voltage power supply
+5 Vdc:
+24 Vdc:
+24VAdc:
Fuse F101 provides overcurrent protection for the fusing system circuitry. Checking or replacing the fuse requires the removal of the ECU. Fuse F102 (found only on 110V units) provides overcurrent protection to the printer DC power supply circuitry. In addition, the +24Vdc, +3.3 Vdc, and +5Vdc power circuitry contains an overcurrent protection circuit that automatically shuts off the output voltage when an overcurrent condition occurs as a result of a short or an abnormal voltage on the load side.
EN
High-voltage power distribution The high-voltage power supply PCA applies an overlap of DC and AC voltage to the primary charging roller and the developing roller. This circuit also applies a positive or negative DC voltage to the transfer roller according to the instructions from the ECU. This circuit also controls the image density by changing the primary AC voltage and the developing AC bias according to the print density setting. High voltage is disabled when the printer door is open.
Figure 12.
EN
Printer functions 73
Figure 13.
Image formation block diagram Toner cartridge As the heart of the image formation system, the toner cartridge houses the cleaning, conditioning, and developing steps of the process. The toner cartridge contains the photosensitive primary charging roller, developing station, toner cavity, and cleaning station. Including these components (which wear, degrade, or are consumed) in the replaceable toner cartridge eliminates the need for a service call when replacement is required. The special photosensitive properties of the drum allow an image to be formed on the drum surface and then transferred to paper.
CAUTION
The printer's toner cartridge does not include a light-blocking shutter. Be careful to avoid exposing the drum to light, which can permanently damage the drum. Protect the toner cartridge whenever removing it from the printer.
EN
Step 1 Conditioning stage (primary charging). This process consists of applying a uniform negative charge to the surface of the drum with the primary charging roller located in the toner cartridge. The primary charging roller is coated with conductive rubber. An AC bias is applied to the roller to erase any residual charges from any previous image. In addition, a negative DC bias is applied by the charging roller to create a uniform negative potential on the drum surface. The amount of DC voltage is modified by the print density setting. Step 2 Writing stage (scanning exposure). During this process, a modulated laser diode projects the beam onto a rotating scanning mirror. As the mirror rotates, the beam reflects off the mirror, first through a set of focusing lenses, then off a mirror, and finally through a slot in the top of the toner cartridge, and onto the photosensitive drum. The beam sweeps the drum from left to right, discharging the negative potential wherever the beam strikes the surface. This creates a latent electrostatic image, which later is developed into a visible image. Because the beam is sweeping the entire length of the drum and the drum is rotating, the entire surface area of the drum can be covered. At the end of each sweep, the beam strikes the beam detect lens, generating the beam detect signal (BD signal). The BD signal is sent to the ECU where it is converted to an electrical signal used to synchronize the output of the next scan line of data. Step 3 Developing stage. At this stage of the process, the latent electrostatic image is present on the drum. The toner particles obtain a negative surface charge by rubbing against the developing cylinder which is connected to a negative DC supply. The negatively charged toner is attracted to the discharged (exposed, grounded) areas of the drum, and repelled from the negatively charged (unexposed) areas. Step 4 Transfer stage. During the transferring process, the toner image on the drum surface is transferred to the paper. A positive charge applied to the back of the paper by the transfer roller causes the negatively charged toner on the drum surface to be attracted to the paper. After separation, the drum is cleaned and conditioned for the next image.
EN
Printer functions 75
Step 5 Separation stage. During the separating process, the paper separates from the drum. To stabilize the feed system and prevent dropouts on the printed image at low temperature and humidity, the charge on the back of the paper is reduced by the static charge eliminator. Step 6 Fixing stage. During the fixing process, the toner is fused into the paper by heat and pressure to produce a permanent image. The paper passes between a heated fusing element and a soft pressure roller. This melts the toner and presses it into the paper. Step 7 Drum cleaning stage. The cleaning blade is in contact with the surface of the drum at all times. As the drum rotates during printing, excess toner is wiped off and stored in the waste toner receptacle.
EN
Step 1 The ECU enables the laser/scanner assembly and the motor. Paper motion begins when the ECU energizes the solenoid (SL001). Step 2 The paper pickup roller rotates once. The paper kick plate pushes the paper against the pickup roller. Step 3 The pickup roller grabs the top sheet and advances it to the feed assembly drive rollers. To ensure that only one sheet is fed, a main separation pad and two subpads hold the remainder of the stack in place. Step 4 The feed assembly drive rollers advance the paper to the paper top photosensor (PS002). This sensor informs the ECU of the exact location of the paper's leading edge, so that the image being written on the photosensitive drum can be precisely positioned on the page. Step 5 The feed assembly drive rollers then advance the paper to the transfer area where the toner image on the photosensitive drum is transferred to paper. Step 6 After the image is transferred, the paper enters the fusing assembly where heat from the fuser and pressure from the pressure roller permanently bond the toner image to paper. The paper exit sensor (PS201) determines that paper has successfully moved out of the fusing area. Step 7 The fusing assembly exit rollers deliver paper to either the paper output bin or the front paper output slot, depending upon the position of the front paper path door.
EN
Printer functions 77
Figure 14.
Printer path
EN
Jam detection
The paper-out sensor (PS001) detects the presence of media in either the single-sheet input tray or the paper input tray. The paper top sensor (PS002) and the paper delivery sensor (PS201) detect media moving through the HP LaserJet 3200 product. If a jam is detected, the ECU immediately stops the printing process and displays a jam message on the control panel. A jam can be detected under any of the following conditions:
l
Pickup delay jam. Media does not reach the paper top sensor after the pickup solenoid (SL001) has been turned on three times (the initial pickup attempt plus two retries) within 7.9 seconds. Pickup stationary jam. The paper top sensor does not detect the trailing edge of media within 7.8 seconds of detecting the leading edge. Delivery-delay jam. The paper delivery sensor does not detect the leading edge of media within 3.2 seconds after the paper top sensor detects the leading edge. Wrapping jam. The paper delivery sensor does not detect the trailing edge of media within 2.4 seconds after the paper top sensor detects the trailing edge. Delivery-stationary jam. The paper delivery sensor detects media for three seconds after the paper top sensor detects the trailing edge of the media. Initial residual-paper jam. The paper delivery sensor or the paper top sensor detect media in the initial rotation period.
EN
Printer functions 79
5
6
4 3 2 1
7 8 9
Figure 15.
Door-open switch (SW301) detects whether or not the printer door is closed and the toner cartridge is present. Printing cannot continue until the printer door is closed and the toner cartridge is in its correct position. Engine-test switch (SW201); see Engine test on page 167 for an explanation of the switch. Paper-top sensor (SL001) detects the leading and trailing edges of the paper. Synchronizes the photosensitive drum and the top of the paper. Pickup solenoid (SL001) enables the pickup roller.
2 3
EN
Paper-out sensor (PS001) senses whether or not media is loaded in the paper input tray. Paper must be loaded before printing can resume. Document sensor (PS1) detects the presence of a document in the document feeder. Document-top sensor detects the leading edge of a document in the document path. Contact image sensor. Paper-delivery sensor (PS201) senses when paper has successfully moved out of the fusing area.
6 7 8 9
EN
Printer functions 81
Period
WAIT From the power-ON until the end of the main motor initial rotation. STBY (Standby) From the end of the WAIT period or the LSTR period until the pickup command is input from the formatter. Or, from the end of the LSTR period until power-OFF. INTR (Initial Rotation Period) After the pickup command has been input from the formatter until the paper reaches the paper top sensor. PRINT (Print) From the end of the initial rotation until the primary voltage goes OFF.
Purpose
To clear the drum surface of potential and to clean the transfer charging roller. To keep the printer ready to print.
Remarks
Detects whether or not the cartridge is installed.
To stabilize the photosensitive drum sensitivity in preparation for printing. Also to clean the transfer charging roller. To form images on the photosensitive drum based on the VIDEO signals (/VDO, VDO) input from the formatter and to transfer the toner image onto the paper. To delivery the last page. Also to clean the transfer charging roller. When the pickup command is input from the formatter, the printer enters the INTR period immediately after the end of the LSTR period.
LSTR (Last Rotation Period) After the primary voltage goes OFF until the main motor stops rotating.
EN
Figure 16.
EN
EN
Chapter contents
Removal and replacement strategy . . . . . . . . . . . . . . . . . . . . 87 Required tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87 Covers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89 DIMMs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89 Back cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 Right side cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91 Left side cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93 Internal paper guide . . . . . . . . . . . . . . . . . . . . . . . . . . . 94 Top cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95 Document scanner assemblies . . . . . . . . . . . . . . . . . . . . . . . 96 Printer door. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96 Document scanner assembly . . . . . . . . . . . . . . . . . . . 100 Contact image sensor. . . . . . . . . . . . . . . . . . . . . . . . . 103 Document scanner pickup roller . . . . . . . . . . . . . . . . . 105 Document scanner separation pad. . . . . . . . . . . . . . . 106 Document scanner motor . . . . . . . . . . . . . . . . . . . . . . 107 Upper guide assembly . . . . . . . . . . . . . . . . . . . . . . . . 108 Control panel/scanner board . . . . . . . . . . . . . . . . . . . 112 Internal assemblies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113 Laser/scanner assembly. . . . . . . . . . . . . . . . . . . . . . . 113 Output roller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114 Delivery assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . 116 Paper exit-sensor flag. . . . . . . . . . . . . . . . . . . . . . . . . 118 Fusing element . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
EN
Chapter contents 85
Gear train motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124 Solenoid. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127 Pressure roller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128 Transfer roller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130 Pickup roller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131 Paper-pickup assembly . . . . . . . . . . . . . . . . . . . . . . . 132 Kick plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134 Separation pad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135 Bottom assemblies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137 Formatter pan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137 Formatter and LIU . . . . . . . . . . . . . . . . . . . . . . . . . . . 138 ECU pan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139 Paper-feed assembly. . . . . . . . . . . . . . . . . . . . . . . . . 141
EN
Note
Required tools
l l l l
#2 Phillips screwdriver with magnetic tip Small flatblade screwdriver Needle nose pliers ESD mat
CAUTION
A Posidriv screwdriver will damage screw heads on the HP LaserJet 3200 Product. Use Phillips screwdriver only.
EN
EN
Covers
DIMMs
1 2 3 Turn the HP LaserJet 3200 product so that you face the back of the product. Lift open the door at the back of the product. Push the anchors on each side away from the DIMMs.
Figure 17.
DIMMs removal 4 5 If there is a DIMM in slot 1, lift it straight up to remove it, and then place it on an ESD mat. Repeat step 4 for the DIMM in slot 2 (memory DIMM) and slot 3 (ROM DIMM).
Note
When reinstalling DIMMs, they must be reinstalled to the slots from which they were removed. 6 After you remove the DIMMs, press the anchors back to their closed position. If the anchors remain in the open position, they can interfere with smooth removal of the back cover. Covers 89
EN
Back cover
1 2 3 Remove the DIMMs (see page 89). Remove two screws from the deep holes (callout 1) in the back cover. Remove a third screw (callout 2) from inside the door on the rear of the product.
2 1
Figure 18.
In one motion, lift the back cover up and pull it away from the product.
EN
2 1
Figure 19.
EN
Covers 91
Release three latches: at the top (callout 1) at the front (callout 2) at the back (callout 3)
2 1
2 3
Figure 20.
Rotate the top of the cover away from the product, and then lift the cover off.
Note
You might have to lift the right side of the product slightly to remove the cover.
EN
Note
You might have to lift the left side of the product slightly to remove the cover.
EN
Covers 93
Figure 21.
EN
Top cover
1 2 3 Remove the DIMMs, the back, right, and left covers, and the internal paper guide (see pages 89 through 94). Remove two screws (callout 1), one from each side of the top cover. Release two latches (callout 2), one at each side of the cover.
2 1
Figure 22.
EN
Covers 95
Callout 2 also shows a metal clip that helps to hold the formatter pan on the ECU pan.
2 2 1
Figure 23.
EN
Lift the formatter pan up slightly, toward the right side of the product, and then rotate the formatter pan down so that it rests on the ESD mat. Release the scanner cable cover (callout 1) by pushing it in the direction of the arrow, and then lift the cover away from the product. Release the connector stay, and then pull the flat, flexible cable (callout 2) out of its connector on the formatter.
Note
The cable is notched so that it clears the speaker. Make sure the cable is reattached in the correct orientation when you reassemble the product.
2 1
Figure 24.
EN
Remove the grounding screw (callout 1) from the flat metal grounding strap.
2 1
Figure 25.
10 Release the flat cable and the strap together from the cable guide. 11 Lift the formatter pan back into place. 12 Replace the three screws in the formatter pan.
EN
13 Tip the product back down so that it rests on its feet. 14 On the right side of the printer door, pull up on the front output door arm (callout 1) to separate it from the front output door. 15 On each side of the printer door, release the tab securing the hinge clip (callout 2) to the hinge, and pull the clip away from the printer door.
2 1
Figure 26. Printer door removal (4 of 4)
16 Open the printer door approximately halfway, and then lift the printer door off of its hinges. Note As you lift the printer door away from the product, make sure that the flat, flexible cable moves smoothly through the slot in the product.
EN
2 1
Figure 27.
Document scanner assembly removal (1 of 3) 3 4 Open the document release door. Rotate the plastic strap at the left side of the printer door clockwise to release the strap.
To reinstall
Make sure you rethread the grounding strap and cable correctly. Failure to do so can damage the cable.
EN
Remove the document scanner guide by lifting it up while pressing the two tabs (callout 1) at the left side of the assembly.
2 1
Figure 28.
EN
6 7
Remove two screws (callout 1) from the document scanner assembly. Use a flatblade screwdriver to press the tab (callout 2) at the center of the assembly, and lift the assembly off of the printer door.
Note
Make sure the contact image sensor cable, at the left side of the product, moves smoothly through the slot as you remove the document scanner assembly.
2 1
Figure 29.
EN
2 1
Figure 30.
EN
Release the contact image sensor with its mounting plate and cover by removing the two screws (callout 1) from the mounting plate and cover.
2 1
Figure 31.
4 5
Lift up the contact image sensor together with its mounting plate and cover. Disconnect the cable from the bottom of the contact image sensor.
Note
Clean the scanner glass after the contact image sensor is reinstalled.
EN
Figure 32.
Lift the right end of the pickup roller shaft out of its mounting; the left end should follow easily.
Note
Once the pickup roller shaft has been removed, parts can easily fall off of the shaft. Upon reinstallation, make sure that all of the parts have been replaced on the shaft in the correct order.
EN
Figure 33.
EN
2 3
2 1 2
Figure 34.
EN
2 3
2 1
Figure 35.
EN
5 6
Place the upper guide assembly on the ESD mat so that the assembly rests on the control panel. Use a flatblade screwdriver to release three tabs (callout 1) on the control panel cover, and then rotate the upper guide assembly up and away from the tabs to separate it from the control panel cover.
2 1
Figure 36.
EN
7 8
Disconnect one cable (callout 1) from the control panel PCB. Remove one screw (callout 2) to release the ground strap.
2 1
Figure 37.
EN
Press the tab (callout 1) down, and then slide the upper guide assembly to the right to release it from the control panel assembly.
2 1
Figure 38.
EN
2 3
2 1
Figure 39.
4 Note
New control panel/scanner boards are not shipped with cables attached. Make sure you keep your cables with the product.
EN
Internal assemblies
Laser/scanner assembly
1 2 3 4 5 Remove the DIMMs, the back, right, and left covers, the internal paper guide, and the top cover (see pages 89 through 95). Open the printer door. Remove the small foam cover over the small cable connector (callout 1) and then release the cable. Disconnect two cables and then release the cables from their cable guides. Remove four screws (callout 2) and then lift the assembly free of the printer.
2 2 1 2
Figure 40.
EN
Output roller
Note This part can be removed without disassembling any other product parts. 1 2 Open the printer door. Using a small flatblade screwdriver, release the plastic snap on the right end of the output roller.
Figure 41.
EN
3 4
Slide the roller to the right, releasing it from the gear on the left. Lift the roller out of the printer.
Figure 42.
EN
Delivery assembly
1 Note Remove the output roller (see pages 114 and 115). The springs underneath the torsion screws are not attached and can come loose during removal. 2 Remove the two screws (callout 1) in the front of the assembly.
2 1
Figure 43.
EN
Gently slide the assembly to the right, and lift it out of the printer.
Figure 44.
EN
Note
Before proceeding, examine the paper exit-sensor flag. It is important to note the position of the spring mechanism on the flag. The spring must be reinstalled to exactly this position, because installing it incorrectly will cause a control panel error message. 2 Remove the paper exit-sensor flag by pressing down on the left side and pulling up on the right side.
Figure 45.
To reinstall
Place the left side of the flag in the correct position first, then slide the right side into place, making certain the spring is on top of the flag. If the spring exerts no pressure on the flag, it might have to be resprung by giving the spring an extra turn before reinstalling. The flag should fit snugly in place.
EN
Fusing element
1 2 Remove the DIMMs, the back, right, and left covers, the internal paper guide, and the top cover (see pages 89 through 95). Also remove the output roller and the delivery assembly (see pages 114 through 117).
Note
Pay special attention to the way these metal clips are attached to the printer chassis before you remove them. This will make reassembly easier. The fusing element is held in place on each end by two metal springloaded clips. Each clip has a small white lever next to it. These levers must be in the up position. 3 Push each clip down and back, releasing it from the printer chassis.
Figure 46.
EN
Figure 47.
Note
During reassembly, make sure the metal clips are seated properly. The front of the metal clip has a small threaded hole. There is a corresponding hole on the printer chassis. Slide the front of the metal clip underneath the threaded tab on the printer chassis so that the two holes line up. Push down on the metal clip (you will feel the tension springs pushing against the clip) until the small metal tab on the back of the clip snaps into place.
EN
The fusing element has electronic cable connections on both the left and right ends, outside the printer. 4 Disconnect the small cable on the left side of the product.
Figure 48.
EN
The larger double cable on the right end is held in place by a plastic snap. 5 Press down on the top of the plastic snap with a flatblade screwdriver.
Figure 49.
Unwind the cable from the cable guides along the side of the printer.
EN
After the two cables are disconnected from the right and left sides of the printer, lift the element gently out of the printer.
Figure 50.
EN
The gear train, located behind the metal plate (gear train cover) on the left side of the printer, must be removed to gain access to the pressure roller. 2 Disconnect the motor cable connection at the back of the printer.
Figure 51.
EN
Remove the four screws (callout 1) securing the metal plate over the gear train, and very gently release it.
2 1
Figure 52.
Note
Some gears are not all held in place and can come apart during removal.
EN
Remove the two screws (callout 1) holding the gear motor to the gear-plate cover.
2 1
Figure 53. Gear train motor (3 of 3)
EN
Solenoid
1 Remove the DIMMs, the back, right, and left covers, the internal paper guide, the top cover (see pages 89 through 95), and the gear train (see pages 124 and 125). Remove the single screw (callout 1) securing the solenoid to the printer chassis.
2 1
Figure 54.
Solenoid removal
3 Note
During reassembly, rotate the clutch so that the flat spot on the clutch allows the feed roller (gear) to turn freely.
EN
Pressure roller
1 2 Remove the DIMMs, the back, right, and left covers, the internal paper guide, and the top cover (see pages 89 through 95). Remove the output roller and the delivery assembly (see pages 114 through 117), and then remove the fusing element and the gear train (see pages 119 through 125). Using a flatblade screwdriver, remove the gear from the end of the pressure roller by gently prying the small plastic tab up from the slot in the end of the roller axles.
Figure 55.
4 CAUTION
The pressure roller is covered with light contact grease. Do not get it on your clothes. See chapter 7, Parts and diagrams, for information about ordering pressure roller grease.
EN
2 1
Figure 56.
Lift the right end of the pressure roller out of the half-bushing and slowly move the roller to the right, pulling the left end of the roller axle out of the opening on the left side of the printer.
Note
The bushings are not connected to the printer chassis and can come loose during removal.
EN
Transfer roller
The transfer roller can be removed without first removing any other product parts. CAUTION Note Do not touch the black portion of the transfer roller. A grounding spring is attached to the bottom of the left end of the transfer roller. This spring can come loose during assembly or removal. 1 2 Open the printer door. Using needle nose pliers, release the transfer roller by gently squeezing the small plastic snaps on the left end of the roller.
Figure 57.
EN
Pickup roller
The pickup roller can be removed without first removing any other product parts. 1 2 Open the printer door. Rotate the bottom of the pickup roller towards the front of the printer.
To reinstall
It is possible to reinstall the pickup roller upside-down. However, for correct operation of the pickup assembly, make sure you reinstall the pickup roller to its correct position. The more rounded portion of the pickup roller should face the front of the product; the circle tab on the blue plastic should be on top, with the straight tab on the blue plastic on the bottom.
EN
Paper-pickup assembly
1 2 3 4 5 Remove the DIMMs, the back, right, and left covers, the internal paper guide, and the top cover (see pages 89 through 95). Disconnect the laser/scanner. Remove the screw attached to a bracket at the right end of the cover plate (callout 1). Remove the two top screws attached to the right and left of the plate (callout 2). Remove the two screws located underneath the plate, securing it to the paper-pickup assembly (callout 3).
2 3
2 1
Figure 58.
EN
Note
The pickup assembly is in several pieces; these pieces should be kept together. Pay close attention to how the assembly is aligned before removing it (see reassembly note on this page). 6 7 Lift the metal plate clear of the printer. Remove the paper-pickup assembly.
Figure 59.
To reinstall
When reassembling this part, you must correctly align and attach the section of the clutch without teeth to the gear.
EN
Kick plate
1 2 3 4 5 Remove the DIMMs, the back, right, and left covers, the internal paper guide, and the top cover (see pages 89 through 95). Also remove the paper pickup assembly (see pages 132 and 133). Disconnect the laser/scanner. Rotate the cam to free the kick plate. Rotate the kick plate arm up approximately 45 degrees and lift the left end up and out of the collar shaft that secures it.
Figure 60.
EN
Separation pad
1 2 3 4 Remove the DIMMs, the back, right, and left covers, the internal paper guide, and the top cover (see pages 89 through 95). Also remove the paper pickup assembly and the kick plate (see pages 132 through 134). Disconnect the laser/scanner. Lift the bottom of the white plastic tab (callout 1) on the rear of the paper-feed frame up slightly and slide it up, toward the top of the paper-feed frame. This will release the separation pad.
Figure 61.
EN
Slide the separation pad out through the brackets that secure it.
Figure 62.
EN
Bottom assemblies
Formatter pan
Note The formatter pan, which contains the formatter and the LIU, can be removed without first removing any other product parts. 1 Note Follow steps 1 through 8 on pages 96 and 97.
Be careful not to damage or break the electronic cables and connections underneath the formatter. 2 3 Remove one grounding screw (callout 1). Pull the flat flexible cable (callout 2) and the small cable (callout 3) out of their connectors.
2 2 1
2 3
Figure 63.
4 Note
EN
2 1 2 3
Figure 64.
EN
ECU pan
1 2 3 Note Remove the DIMMs, the back, right, and left covers, the internal paper guide, and the top cover (see pages 89 through 95). Remove the printer door (see pages 96 through 99), and the formatter pan (see page 137). Disconnect the ECU cable.
If the fusing element cables are connected, disconnect them before removing the ECU pan. 4 5 Remove the two screws fastened to the brackets on the sides of the pan. Remove the two screws reached through openings in the side of the black plastic printer chassis.
Figure 65.
Disconnect the small solenoid connection from the back of the ECU.
EN
7 CAUTION
Slowly lift the ECU plate away from the printer chassis.
Be very careful not to damage or break the connectors underneath the ECU plate as you lift it from the printer chassis. 8 Reach between the plate and the chassis and unwind the cables from their cable guides until there is enough slack in the cables to allow access to the bottom of the ECU plate. Unwind and disconnect all cables until the ECU board is separated from the chassis.
Figure 66.
Note
The entire ECU board can be replaced as a single unit (cables do not ship with the replacement board; if cables are damaged during removal, you will have to purchase new ones).
EN
Paper-feed assembly
1 2 3 4 5 Remove the DIMMs, the back, right, and left covers, the internal paper guide, and the top cover (see pages 89 through 95). Remove the printer door (see pages 96 through 99), the formatter pan (see page 137) and the ECU pan (see pages 139 and 140). Disconnect the two cable connections (callout 1). Partially unwind the cables from their cable guides. Remove the two screws (callout 2) securing the assembly to the printer chassis.
2 2 1
Figure 67.
Lift the paper-feed frame away from the chassis, being careful not to damage sensor flags.
To reinstall
Be sure to seat the tab into the frame.
EN
Release the snap catches inside the gear on the left end of the paper-feed roller shaft.
Figure 68.
EN
Slide the paper-feed roller to the right, and remove it from the printer chassis.
Figure 69.
EN
EN
Troubleshooting
Chapter contents
Basic troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146 Errors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149 Image formation troubleshooting . . . . . . . . . . . . . . . . . . . . . 156 Checking the toner cartridge . . . . . . . . . . . . . . . . . . . 156 Solving image-quality problems . . . . . . . . . . . . . . . . . 157 Solving paper feed problems . . . . . . . . . . . . . . . . . . . . . . . . 164 Functional checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167 Engine test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167 Half-self-test functional check. . . . . . . . . . . . . . . . . . . 168 Drum rotation functional check . . . . . . . . . . . . . . . . . . 169 Heating element check . . . . . . . . . . . . . . . . . . . . . . . . 170 High-voltage power supply check. . . . . . . . . . . . . . . . 171 Paper curl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170 Paper path check . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173 Service mode functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174 Troubleshooting tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181 Internal reports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181 Printing all fax reports at once . . . . . . . . . . . . . . . . . . 182 T.30 protocol trace . . . . . . . . . . . . . . . . . . . . . . . . . . . 183 Repetitive image defect ruler . . . . . . . . . . . . . . . . . . . 191 Document scanner recalibration. . . . . . . . . . . . . . . . . 192 Main wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 194
EN
Basic troubleshooting
Table 10. Basic troubleshooting
# Verification steps Is Power On successful?
When the product is connected to a grounded power source, the printer motor should rotate for approximately six seconds and the document scanner motor should rotate for approximately two seconds.
Possible problems
No power.
Solutions
1. Verify that the product is plugged in. 2. Verify that the power cable is functional. 3. Verify that FU102 on the ECU is not open. 4. If all of these conditions are correct, replace the ECU. 1. Verify that the toner cartridge is present. 2. Verify that the printer door is closed. 3. Verify that paper is loaded in the paper input tray. 4. Verify that printer path paper sensors are functional. 5. Verify that the motor connector J1 is seated into the ECU. 6. Verify that the motor is correctly mounted to the printer chassis. 7. If all of these conditions are correct, replace the ECU. 8. If, after replacing the ECU, the printer motor still does not rotate, replace the motor. 1. Verify that the document scanner connector is seated in the formatter. 2. Verify that the document scanner motor is correctly mounted in the document scanner assembly. 3. If these conditions are met, replace the document scanner motor. 4. If, after replacing the motor, the document scanner motor still does not rotate, replace the formatter. 5. If, after replacing the formatter, the document scanner motor still does not rotate, replace the ECU. Consult the list of common messages later in this chapter to correct the error. Verify that the control panel cable is seated into both the control panel and the formatter. If the cable is connected correctly, replace the control panel.
EN
Possible problems
Solutions
Note
Engine test is not successful.
Control panel displays an error message. Media does not move smoothly through the printer paper path. Poor print quality.
Media does not move smoothly through the document scanner path.
The telephone line is not operational or the product is not plugged into the telephone line. The telephone cable is plugged into the wrong connector. The products fax settings are set incorrectly. The LIU is not operational.
Try plugging the phone cord into the other connector. Review and reset the products fax settings. Replace the LIU. Make sure that the product is the only device on the telephone line and try again to receive the fax.
Too many telephone devices are plugged in, or telephone devices are not connected in the correct order The products fax settings are set incorrectly. The LIU is not operational.
Review and reset the products fax settings. Replace the LIU.
EN
Solutions
Uninstall and then reload the product software. Make sure you use the correct installation procedure and the correct port setting. Reconnect the cable. Reset the printer driver. Disconnect the other devices and try again to print. Reset the computers port settings.
7 8
Replace the formatter Disconnect the other devices and try again to scan. Check hardware documentation to see if the port configuration can be changed. Reset the computers port settings. If the problem persists, reset the BIOS settings in CMOS. Start HP LaserJet Director and turn on polling.
Other devices are connected to the parallel port. The computers parallelport hardware is not bidirectional. The BIOS settings for the parallel port are set incorrectly. Polling is turned off in HP LaserJet Director or HP LaserJet Director is not running.
EN
Errors
These control panel error messages are listed alphabetically. Messages are accompanied by the cause of the message and steps to resolve the error. Table 11. Control panel error messages Message
50 FUSER ERROR
Cause
The product has experienced an internal hardware error.
Solution
Disconnect the power cable from the product, wait at least 30 seconds, then reconnect the power cable and wait for the product to initialize. Check the cabling connections to the heating element. Perform the heating element check (see page 170). If the error persists, replace the heating element. If, after replacing the heating element, the error persists, replace the ECU. Disconnect the power cable from the product, wait at least 30 seconds, then reconnect the power cable and wait for the product to initialize. Check the cabling connections to the laser/scanner. Try connecting the product to a different power source or surge protector. If the error persists, replace the laser/scanner. Disconnect the power cable from the product, wait at least 30 seconds, then reconnect the power cable and wait for the product to initialize. Try connecting the product to a different power source or surge protector. If the error persists, replace the contact image sensor. If, after replacing the contact image sensor, the error persists, replace the formatter.
51 LASER ERROR
52 SCANNER ERROR
EN
Errors 149
Cause
The product has experienced an internal hardware error.
Solution
Disconnect the power cable from the product, wait at least 30 seconds, then reconnect the power cable and wait for the product to initialize. If the error persists, replace the formatter. Disconnect the power cable from the product, wait at least 30 seconds, then reconnect the power cable and wait for the product to initialize. If the error persists, replace the formatter. Disconnect the power cable from the product, wait at least 30 seconds, then reconnect the power cable and wait for the product to initialize. Check the cabling to the ECU. If the error persists, replace the ECU. Disconnect the power cable from the product, wait at least 30 seconds, then reconnect the power cable and wait for the product to initialize. If the error persists, replace the formatter. Disconnect the power cable from the product, wait at least 30 seconds, then reconnect the power cable and wait for the product to initialize. If the error persists, replace the formatter. Disconnect the power cable from the product, wait at least 30 seconds, then reconnect the power cable and wait for the product to initialize. If the error persists, replace the formatter. Disconnect the power cable from the product, wait at least 30 seconds, then reconnect the power cable and wait for the product to initialize. If the error persists, replace the formatter.
54 PRINTER ERROR
55 DC CONTROLLER ERROR
79 SERVICE (####)
80 SERVICE (####)
81 SERVICE (####)
EN
Cause
Fax communication error occurred between the product and the sender or receiver. For brief descriptions of communication errors see table 12, Communication errors, on page 155.
Solution
Allow the product to retry sending the fax. Unplug the product telephone cord from the wall, plug in a telephone, and try making a call. Plug the product phone cord into a jack for another phone line. If the error persists, replace the LIU. Open the document release door, clear the jam, close the document release door, and reload the paper into the document feeder tray. If the error persists, replace the document scanner separation pad and document scanner pickup roller. Remove and reload the media into the document feeder tray. If the error persists, replace the document scanner pickup roller. Call the recipient to ensure that fax machine is on and ready. Check that you are dialing the correct fax number. Check that the redial option is enabled. Unplug the telephone cord from both the product and the wall and replug the cord. Unplug the product telephone cord from the wall, plug in a telephone, and try making a call. Plug the product phone cord into a jack for another phone line. If the error persists, replace the LIU.
DOCUMENT FEEDER MISPICK. RELOAD MEDIA FAX DOES NOT ANSWER CANCELED SEND
Attempts to redial a fax number failed or the redial on no answer option was turned off.
EN
Errors 151
Cause
You tried to send a fax, but the receiving fax line did not answer. The product attempts to redial after a few minutes.
Solution
Allow the product to retry sending the fax. Call the recipient to ensure that fax machine is on and ready. Check that you are dialing the correct fax number. Check that the redial on no answer option is enabled. Unplug the product telephone cord from the wall, plug in a telephone, and try making a call. Plug the product phone cord into a jack for another phone line. If the error persists, replace the LIU. Unplug the telephone cord from both the product and the wall and replug the cord. Unplug the product telephone cord from the wall, plug in a telephone, and try making a call. Plug the product phone cord into a jack for another phone line. See Changing the detect dial tone setting in the online user guide. If the error persists, replace the LIU. If, after replacing the LIU, the error persists, replace the formatter. Allow the product to retry sending the fax. Unplug the product telephone cord from the wall, plug in a telephone, and try making a call. Plug the product phone cord into a jack for another phone line. If the error persists, replace the LIU.
NO DIAL TONE.
NO FAX DETECTED
The product answered the incoming call but could not determine that the caller was a fax machine.
EN
Cause
The product has detected a power failure and is performing a self-test.
Solution
The product should go back to the ready state on its own. If this message does not go away in a couple of minutes, disconnect the power cable from the product, wait at least 30 seconds, then reconnect the power cable and wait for the product to initialize. If the message reappears frequently, troubleshoot the product by following the steps in Basic troubleshooting on page 146. Unplug the product and check the indicated DIMM. Clear the jam. The job should continue to print. If it does not, try reprinting the job. If media jams frequently, see chapter 3, Maintenance. Reload the paper in the paper input tray and press ENTER/ MENU to continue the job. If the error persists, replace the printer pickup roller. Call the recipient to ensure that fax machine is on and ready. Check that you are dialing the correct fax number. Check that the redial on busy option is enabled. Press and hold STOP/CLEAR for seven seconds to check for a dial tone. Unplug the product telephone cord from the wall, plug in a telephone, and try making a call. Plug the product phone cord into a jack for another phone line. If the error persists, replace the LIU.
POWER OFF. CHECK DIMM #[1-3] PRINTER PAPER JAM CLEAR PAPER PATH
The DIMM in the indicated slot has failed. The product has detected that a jam has occurred.
The fax line to which you were sending a fax was busy. The product has cancelled sending the fax.
EN
Errors 153
Cause
The fax line to which you were sending a fax was busy. The product automatically redials the busy number. (See Changing how the product redials in the online user guide.)
Solution
Allow the product to retry sending the fax. Call the recipient to ensure that fax machine is on and ready. Check that you are dialing the correct fax number. Unplug the product telephone cord from the wall, plug in a telephone, and try making a call. Plug the product phone cord into a jack for another phone line. If the error persists, replace the LIU.
EN
EN
Errors 155
o Make sure that the toner cartridge is seated properly. o Inspect the toner cartridge for remaining toner. o Check the expiration date stamped on the toner cartridge box. o Check the toner cartridge to see if it has been disassembled or refilled. o Inspect the cartridge to see if toner is leaking through worn seals. o Check the surface of the photosensitive drum in the cartridge to see if it has been damaged or scratched. Touching the drum contaminates the photosensitive surface and can cause spotting and image defects. o Blurred areas on printed pages indicate that the photosensitive drum in the cartridge has been overexposed to light. Because overexposure to light causes permanent damage to the photosensitive drum, the cartridge should be replaced.
Note A toner cartridge weighs approximately 702 grams (24.7 ounces) when it is full and approximately 594 grams (20.9 ounces) when it is empty.
EN
Solution
To get the image to fit into this printable area, slightly reduce the size of the image.
For printing, check the reduction setting in the Print or Setup window from within the program you are using. Copied images will be clipped if the image on the original is too close to edge of the original.
The HP LaserJet 3200 product is not plugged in. The parallel cable is loose.
Make sure that the HP LaserJet 3200 product is plugged into a live wall outlet or power strip. Check that the parallel cable is securely connected between the HP LaserJet 3200 product and the computer. Adjust the contrast and resolution settings from the HP LaserJet Director. Recalibrate the product. Adjust the resolution and contrast setting(s) from the toolbox on the HP LaserJet Director. If the original was on a colored paper, including brown recycled paper, the text might not be clear. Adjust the resolution, contrast, and brightness settings from the toolbox on the HP LaserJet Director.
The contrast is not set correctly. The HP LaserJet 3200 product needs to be recalibrated. The original image is very light or very dark. The scanned image is too light or too dark because the original was on a colored paper.
EN
Solution
Redistribute the toner or replace the toner cartridge. See chapter 3, Maintenance. Make sure that the media meets specifications detailed in HPs media specifications guide. Adjust the setting from the control panel. Follow the steps in Basic troubleshooting on page 146 to isolate the problem. Clean the mirror by blowing air through the laser/scanner to remove any dust particles. Replace the laser/scanner. Follow the instructions in chapter 3, Maintenance, to recalibrate the document scanner. Replace the contact image sensor. Replace the formatter. Make sure that the media meets specifications detailed in HPs media specifications guide. Remove the paper from the paper input tray and turn it over. (The wrapper on many reams of paper has an arrow indicating the print side.) See chapter 3, Maintenance, for instructions on cleaning the product and using a cleaning page. Replace the toner cartridge if maintenance procedures do not improve print quality.
Stains or smudges appear as small, round, black dots on the front or back of a page. Sometimes inconsistent stains appear.
The media you are using does not meet HPs specifications (for example, it is too moist or too rough). You are printing on the wrong side of the paper.
The HP LaserJet 3200 product needs to be cleaned. The toner cartridge is damaged.
EN
Solution
See chapter 3, Maintenance. Replace the toner cartridge if maintenance procedures do not improve print quality. Perform the heating element check (see page 170).
If scanned images have unwanted lines through them: There is ink, glue, white-out, or some other substance on the contact image sensor. Slick paper caused the document scanner trouble in scanning. The HP LaserJet 3200 product needs to be recalibrated. See chapter 3, Maintenance.
EN
Solution
Make sure you removed the entire length of the sealing tape from the toner cartridge before you installed it. Replace the toner cartridge. See chapter 3, Maintenance. Perform the heating element check (see page 170). Perform the drum rotation functional check (see page 169). Replace the laser/scanner. See chapter 3, Maintenance. Replace the contact image sensor. Use the repetitive image defect ruler (see page 191) to determine which roller is damaged. Replace the roller. See chapter 3, Maintenance. Make sure that the media meets specifications detailed in HPs media specifications guide. Try changing to a paper with a smoother finish. Replace the toner cartridge. Replace the toner cartridge.
The HP LaserJet 3200 product needs to be cleaned. If you are using transparencies, they do not meet HPs specifications. The papers texture is too coarse. The toner cartridge is damaged, causing a repetitive black flaw on every printout. The toner cartridges photosensitive drum has been overexposed to bright light, causing repetitive defects (usually a fuzzy black area).
Character voids appear (white areas within the parts of characters that should be solid black).
The paper or transparencies do not meet HPs specifications. You are printing on the wrong surface of the paper. Poor fusing.
Make sure that the media meets specifications detailed in HPs media specifications guide. Remove the paper and turn it over. (The wrapper on many reams of paper has an arrow indicating the print side.) Check for a wrap jam in the fuser.
EN
Solution
Try changing the print density setting. If that doesnt work, change the paper type, weight, or surface finish. If background scatter occurs on an envelope, try moving the text to an area with no seams. Printing on seams can cause this problem. See To clean the print path on page 54. See Cleaning the product on page 54. See To clean the product and replace the pickup roller on page 55. Reconnect the formatter. The formatter must be connected during an engine test. Remove the cartridge and reinstall it. Replace the toner cartridge. Perform the high-voltage power supply check (see page 171). Follow the steps in Basic troubleshooting on page 146 to isolate the problem. Replace the ECU or the laser/scanner, as needed. Try reprinting the job. Adjust the print density from the control panel. Make sure that the media meets HPs specifications. Make sure that the media meets specifications detailed in HPs media specifications guide. Try a normal or best setting.
Background scatter can be caused by toner buildup on the pressure roller. Toner has spilled inside the product. The pickup roller is dirty.
An engine test was performed when the formatter was disconnected. The toner cartridge was improperly installed. The toner cartridge is defective. Continuity in the high-voltage contact points is interrupted. There is a problem in the ECU or the laser/scanner.
A single sheet of paper is defective. The print density needs to be adjusted. The moisture content of the paper is inconsistent or the paper has moist or wet spots on the surface. The paper was damaged by inconsistent manufacturing processes. A draft mode or economy mode is selected in the software.
EN
Solution
If you are printing on small-sized paper and the page is blank, try printing on larger paper to see where the image is printing. Adjust the margins accordingly. Remove the paper from the paper input bin and align the edges of the paper. Break the ream of paper by curving it into an upside-down u-shape. Try turning the paper around to feed the other end first, or use a different type of paper. Clean the pickup roller and the separation pad. If the problem persists, replace the separation pad or subpads.
Your HP LaserJet 3200 product is feeding two or more sheets of paper at a time because the paper is difficult to separate.
Check your softwares printing configuration information. If you are using a word-processing program, check for a natural page break and a forced page break that are close to each other. Make sure you removed the entire length of the sealing tape from the toner cartridge before you installed it. Replace the toner cartridge. Perform the high-voltage power supply check (see page 171). Print a self-test page. If the page is blank, follow the steps in Basic troubleshooting on page 146 to isolate the problem. Replace the laser/scanner or the ECU as needed. Remove some of the media. Be sure to center the media with the paper guides. Also, verify that the paper guides are not adjusted too tightly or too loosely against the media. Make sure that the media meets HPs specifications.
The toner cartridge was improperly installed. The toner cartridge is completely out of toner. Discontinuity exists in the high-voltage contact points. There is a problem in a part of the product.
The paper input tray is overfilled. The guides are adjusted improperly.
The papers weight or surface finish does not meet HPs specifications.
EN
Solution
See chapter 3, Maintenance.
Adjust the resolution, contrast and brightness setting(s) from the toolbox on the Document Manager. If the original was on colored paper, including brown recycled paper, the text might not be clear. Try adjusting the resolution, contrast, and brightness settings from the toolbox on the Document Manager. Replace the contact image sensor.
EN
Solution
Use the front paper output slot by opening the front paper path door. Reset the fuser mode to the default. Whenever possible, store paper in its sealed ream at room temperature. Check for broken or missing document feeder tray guides and replace as necessary. Do not try to pull the page out because you can damage the document scanner. To remove the page, open the document release door and remove the jammed media. Remove some of the media. Be sure to center the paper with the guides. Verify that the guides are not adjusted too tightly or too loosely against the paper. Check for broken or missing paper guides and replace scanner as necessary. Make sure that the media meets specifications detailed in HPs media specifications guide. Be sure to center the paper with the guides. Also, verify that the guides are not adjusted too tightly or too loosely against the paper. Check for broken or missing document feeder tray guides and replace scanner as necessary.
The papers weight or surface finish does not meet HPs specifications.
EN
Solution
Slide the guides against the sides of the stack in the paper input tray or against the single sheet in the single-sheet input tray to center the paper. Make sure the guides are not adjusted too tightly. Slide the special media lever back to the normal position. Only slide the special media lever to the right when copying or scanning special media. Always remove paper from the paper input tray before refilling it. Remove some of the sheets. The paper input tray can hold up to 125 sheets of 20-lb. (75g/m2) bond weight paper (less for heavier paper) or from 7 to 10 envelopes. Place only one sheet at a time in the single-sheet input slot. Break the ream of paper by curving it into an upside-down u-shape; this can effectively decrease multifeeds. Also try turning the paper around to feed the opposite end first, or use a different type of paper. Make sure that the media meets specifications detailed in HPs media specifications guide. Do not allow more than 100 sheets of 20lb (75g/m2) bond weight paper (less for heavier paper) to fill the paper output bin. See chapter 3, Maintenance. Replace the pickup roller. Clean the separation pad. Replace the separation pad. Check the sensors to make sure that none of them are jammed. If a sensor cannot be unjammed, replace the sensor. Perform the paper path check (see page 173) to determine which parts should be replaced.
Paper was not removed from the paper input tray before refilling the tray. The paper input tray is overfilled.
More than one sheet was placed in the single-sheet input slot. The paper was poorly cut by the manufacturer and is sticking together.
The paper does not meet HPs specifications for print media. The output capacity was exceeded in the paper output bin or front paper output slot. The pickup roller is dirty. The pickup roller is damaged. The separation pad is dirty. The separation pad is damaged. A sensor is not operating properly.
EN
Solution
Remove the document from the document feeder tray. Straighten the item, then reinsert it. Slide the guides against the sides of the item to center it. Make sure the guides are not adjusted too tightly. Remove some of the sheets. The document feeder tray can hold up to 10 pages, depending on the thickness of the pages. Make sure that the media meets specifications detailed in HPs media specifications guide. See chapter 3, Maintenance.
The item was too thick, too slick, or otherwise did not meet specifications. The document scanner pickup roller or separation pad is dirty and cannot feed the document. The document scanner pickup roller or separation pad is damaged or worn. The sensor is not operating properly.
Replace the scanner. Check the sensor to make sure it is not jammed. If a sensor cannot be unjammed, replace the scanner. Check the path for obstructions. Readjust as necessary or replace the scanner. Do not try to pull the page out because you may damage the document scanner. Open the document release door and remove the jammed media. Then, curl or roll the item in the direction of the printed side, unroll it, and reload the item.
Items loaded in the document feeder tray fall forward out of the tray.
EN
Functional checks
Engine test
The engine test is used to verify that the print engine is functioning correctly. The formatter is bypassed during an engine test, so the engine test is useful for isolating printer problems. The engine test prints vertical lines down the entire printable area of a page and is also useful for checking and adjusting registration.
Figure 70.
EN
Image formation stage (charges the drum and writes a latent image to the drum with the laser) Development stage (forms a toner image on the drum) Transfer stage (transfers the image to paper) Cleaning stage (removes excess toner from the drum) Fusing stage (applies heat and pressure to make the image on paper permanent)
The purpose of the half-self-test check is to determine which process is malfunctioning. Perform the test as follows: 1 2 Print a demonstration page (see To print a demonstration page on page 181). Open the printer door after the paper advances half-way through the printer (about 8 seconds after the motor begins rotation). The leading edge of the paper should have advanced past the toner cartridge. Remove the toner cartridge. Open the toner cartridge drum shield to view the drum surface. If a dark and distinct toner image is present on the drum surface, assume that the first two functions of the electrophotographic process are functioning (image formation and development). Troubleshoot the failure as a transfer or fixing problem.
3 4
If there is no image on the photosensitive drum, perform the following functional checks: 1 2 3 Make sure you have removed the entire length of the sealing tape from the toner cartridge before you installed the cartridge. Perform a drum rotation functional check. Perform a high-voltage power supply check.
EN
If the mark did not move, inspect the main drive assembly to make sure that it is meshing with the toner cartridge gears. If the drive gears appear functional and the drum does not move, replace the toner cartridge. Note This test is especially important if refilled toner cartridges have been used.
EN
Note
Normal resistance is 30 ohms +/- 10 ohms. 4 5 If no resistance is measured, replace the heating element. Remove the thermistor connector (see figure 48 on page 121) and measure the resistance between pins one and two.
Note
Normal resistance is 440K ohms +/- 30K ohms at 68 F (20 C). 6 If no resistance is measured, replace the heating element.
Paper curl
Paper curl is inherent to the laser printing processes, and occurs when paper is subjected to heat. Paper curl tends to relax as the paper cools while resting on a flat surface. The specification for maximum paper curl when the paper is lying flat before print is 0.2 inches (5 mm).
EN
2 1 2 2 3
Figure 71.
EN
Figure 72.
EN
Motor rotation Solenoid action Kick plate motion Paper pickup roller motion Drive roller, transfer roller, fuser roller and gear, and delivery roller motion
To override SW301
2 1
Figure 73.
Overriding SW301 1 2 3 4 5 6 Remove the printer covers Install the toner cartridge. Make sure the fuser levers on the delivery assembly are closed. Press SW301- front door interlock (callout 1). Press laser/scanner interlock switch on laser/scanner (callout 2) While SW301and laser/scanner interlock is engaged, perform an engine test to observe paper motion. (See procedures earlier in this chapter.) Functional checks 173
EN
Main menu
Secondary service
Submenu
Secondary reports
Submenu
Continuous self-test Data store report Translations Ext keypad map Red-corrected Blue-corrected Green-corrected Red-uncorrected Blue-uncorrected Green-uncorrected
Scanline data
EN
Developers menu
Use the developers menu to adjust fax data store parameters and to run various tests. Below is a hierarchical diagram of the developers menu:
Main menu
Developers menu
Submenu
R/W parameter Monitor test
Submenu
Onhook monitor Offhook monitor Eavesdrop monitor Signal pwr monitor LIU inputs LIU ID OIU outputs
LIU test
After you enter the developers menu, the control panel display should read R/W PARAMETER.
See the HP LaserJet 3200 product software technical reference for a complete list of fax data store parameters.
EN
Diagnostic mode
Use diagnostic mode to check the functionality of LEDs, the control panel display LCDs, and to check the firmware version. Note Diagnostic mode is available for firmware version 2.2 or higher.
The table below shows the tests and key sequences to perform in diagnostic mode: Table 15. Diagnostic mode key sequences To perform this test . . .
Toggle LED1 on/off Toggle LED2 on/off Access LCD pattern 1 (solid fill) Access LCD pattern 2 (empty fill) Access LCD pattern 3 (> fill) Access LCD pattern 4 (H fill) Access LCD pattern 5 (frame fill) Access LCD pattern 6 (check fill) Access LCD pattern 7 (ROM check) Access firmware version number
EN
For each key pressed during the test, a "+" character appears on the LCD (initially, five "+" characters appear on the screen to account for the 9 on the one-touch keypad and for four other spaces that have no key correspondence). When all of the keys have been pressed, the display fills with "+" characters. Pressing any other key after the display is full results in the message "OK" on the control panel display also causes both LEDs to toggle on and off.
EN
NVRAM init
NVRAM init sets all default variables stored in NVRAM back to factory default values or to a default ROM value, depending on the variable, and performs a system reset. NVRAM init resets the following:
l l l
all menu settings to factory default values including fax header and company name factory settings such as formatter number, page counts, and factory paper settings fax memoryall faxes in memory are erased
EN
The table below provides a more detailed description of the NVRAM PJL factory variables and commands and shows possible settings for each.
N V R A M P JL V a r ia b le o r C o m m a n d
DEFAULT PAPER
P o ssib le settin g s "LETTER", "LEGAL, "A4", "EXECUTIVE, "COM10, "MONARCH, "DL, "C5, "B5", "CUSTOM" " ROMAN8" , " ISOL1" , " ISOL2" , " ISOL5" , " PC8" , " PC8DN" , " PC850" , " PC852" , " PC8TK" , " WINL1" , " WINL2" , " WINL5" , " DESKTOP" , " PSTEXT" , " VNINTL" , " VNUS" , " MSPUBL" , " MATH8" , " PSMATH" , " VNMATH" , " PIFONT" , " LEGAL" , " ISO4" , " ISO6" , " ISO11" , " ISO15" , " ISO17" , " ISO21" , " ISO60" , " ISO69" , " WIN30"
ON, OFF 0-2147483647 0-2147483647 0-2147483647 None - Command None - Command
DEFAULT OEM DEFAULT PRINTPAGECOUNT DEFAULT SCANPAGECOUNT DEFAULT COPYPAGECOUNT CLEARNVRAM NVRAM INIT
Figure 74.
EN
To use these commands, you need some method to send PJL commands to the printer, either with a software tool or by copying a binary file that contains the commands from the host using a DOS box. For example, from the DOS prompt: copy /b filename lpt1 Here is an example of a file that uses one of the commands: ESC%-12345X@PJL SET SERVICEMODE=HPBOISEID @PJL command @PJL RESET Here is an example of using the NVRAMINIT command: ESC%-12345X@PJL SET SERVICEMODE=HPBOISEID @PJL NVRAMINIT @PJL RESET Note Set SERVICEMODE before trying to set the variable or you will not get the desired result. Also reset the PJL to be sure the SERVICEMODE status is cleared. To create these files, you need an editor that can insert the ESC character or is able to copy it in from a existing file. If a software tool is used, simply send the same strings in the same order as given for the example files.
EN
Troubleshooting tools
Internal reports
Use the control panel to print configuration reports and demonstration pages. The configuration report shows the settings selected from the control panel. The control panel menu structure might be a useful reference as you alter settings in the menu.
EN
Fax activity logrecent faxes sent and received, and status Billing log (if enabled)prints by billing code Block fax list (if enabled)fax numbers you have blocked Configuration reportcurrent control panel settings, including the following sections: System information Reports Fax settings User defaults Service Softswitch settings Page counts
EN
EN
Use the control panel service menu to choose T.30 Protocol Trace and then select At the end of each call. Configure another fax machine, preferably another HP LaserJet 3200 product, to the same (or similar) settings. Send a fax from the product or receive a fax to the product from the other fax machine. The fax trace report prints after the fax prints. Explanations of some of the reports column heading follow:
l l l
Start time is the time the fax begins. Match it with the fax log of errors. Type is the type of fax activity, send or receive. Mode is the transmission mode. If it begins with EC, error correction was turned on. The set of three numbers is the BAUD rate divided by 100. For example, EC144 in the mode column means that error correction was on and the transmission speed was 14,400 bps. Status explains the status of the fax: Completed means that the fax was successful. Pending faxes are in memory or are printing. Error numbers and their meanings appear in the user guide.
EN
Called station
Phase ACall setup sequence
EN
Comments
Appropriate responses
Identifying capabilities: from a manual receiver (NSC) (CIG) DTC or an auto-answer unit (TSI) DCS (NSF) (CSI) DIS (CRP) (TSI) (NSS) (PWD) (SEP) (CIG) DTC (PWD) (SUB) (TSI) DCS Mode setting command: from calling unit Poll operation Mode setting command: from manual transmitter or automatic receiver This command is always followed by phasing/ training. (TSI) DCS (NSF) (CSI) DIS (CRP) (TSI) (NSS) CFR FTT (NSC) (CIG) DTC (NSC) (CIG) DTC
(NSC) (CIG) DTC (PWD) (SEP) (CIG) DTC (TSI) DCS (TSI) (NSS) (PWD (SUB) (TSI) DCS CTC (EOR-NULL)
Mode setting command: from the transmitter to (CTR) the receiver (CRP) Indicates the next block transmission from the transmitter to the receiver The receiver (ERR) (RNR) (CRP) (ERR) (RNR) PIN (CRP)
Any one of the following: l (EOR-EOP) l (EOR-EOM) l (EOR-PRI-MPS) l (EOR-PRI-EOP) l (EOR-PRI-EOM) Any one of the following: l MPS l EOP l EOM l (PRI-MPS) l (PRI-EOP) l (PRI-EOM) (PPS-NULL)
Post-message commands
MCF RTP RTN PIP PIN (CRP) (PPR) MCF (RNR) (CRP)
Post-message command for a partial page from the transmitter to the receiver
Any one of the following: l (PPS-MPS) l (PPS-EOP) l (PPS-EOM) l (PPS-PRI-MPS) l (PPS-PRI-EOP) l (PPS-PRI-EOM) (RR)
Post-message commands for a complete page (PPR) from the transmitter to the receiver MCF (RNR) PIP PIN (CRP) Ask for the status of the receiver: from the transmitter to the receiver (RNR) (ERR) MCF PIP PIN (CRP) None
DCN
Phase E command
EN
DCN DCS DIS DTC DOM EOP EOR EQM ERR ECD FCF FCS FDM FIF FSK
Disconnect Digital command signal Digital identification signal Digital transmit command End of message End of procedure End of retransmission Eye quality monitora measure of the modem signal quality, lower numbers indicate better signals Response for end of retransmission Facsimile coded date Facsimile Frame check sequence File diagnostics message Facsimile information field Frequency shift key. Low-speed command identifier separating commands/scans; precedes command mode.
X011 1111
FTT
Failure to train. The 1.5 seconds of the Training Check X010 0010 Frame (TCF) indicates line conditions are not good enough for this modulation. Group command Group identification High-level data link control Line conditioning signals 1100 Hz 1300 Hz for 1.5 to 100 seconds 2100 Hz for 1.5 to 100 seconds 1650 or 1850 Hz
GC GI HDLC LCS
EN
XID ???
EN
555-nnnn
Example of a successfully sent fax Phase A, call establishment, does not show up on a trace report. Phase C is the phase in which faxed pages are transferred.
EN
Figure 76.
Explanation of DBM
-dBM values shown on the fax trace report are hexadecimal numbers. Convert the value to a base-10 number and then divide by 5 to check signal strength. Using the example above, where DBM=34: 34 (hex) = 52 (decimal) and 52/5 = 10.4
Assuming a negative value, -10.4 falls into the range of -10 to -43 (with -43 being a weak signal). -10.4 is, therefore, a strong signal.
EN
Developing cylinder (32 mm) Delivery roller (37.7 mm) Primary charging roller (38 mm) Transfer roller (45 mm)
Pressure roller (62.8 mm) Upper heating element film (76 mm) Toner cartridge photosensitive drum (76 mm)
Figure 77.
EN
Note If toner is the contaminant, you might have to scrape it off of the glass. Be careful not to scratch the glass. 4 At the product control panel, press the 10 on the one-touch keypad to print the demonstration page. Copy the demonstration page.
EN
10
If the vertical black or white line appears on the copy of the demonstration page, continue with steps 7 through 13 below. On the control panel, press ENTER/ MENU. Press < once to display SERVICE and press ENTER/MENU. Use the < and > keys to select SCAN CALIBRATION and press ENTER/ MENU.
7 8 12 9
10 Insert a blank, white piece of lettersized paper into the document feeder tray. 11 Press ENTER/MENU to begin the scan calibration. The HP LaserJet 3200 product pulls the piece of paper through and then prints a calibration graph. 12 Examine the calibration graph. A dip in the calibration graph can indicate an image defect. Note Dips at the ends of the calibration graph are normal. 13 Line up the calibration graph with a newly copied page. If the dip in the calibration graph corresponds to the black or white line, the contaminant is likely internal and the contact image sensor assembly should be replaced.
EN
Main wiring
Figure 78.
Main wiring (1 of 2)
EN
Figure 79.
Main wiring (2 of 2)
EN
Locations of connectors
Figure 80.
Locations of connectors (1 of 3)
EN
Figure 81.
Locations of connectors (2 of 3)
Figure 82.
Locations of connectors (3 of 3)
EN
EN
Chapter contents
Ordering parts and supplies . . . . . . . . . . . . . . . . . . . . . . . . . 200 Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200 Related documentation and software . . . . . . . . . . . . . 201 Consumables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 201 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 202 How to use the parts lists and diagrams . . . . . . . . . . . . . . . 203 Common hardware. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 204 Assembly locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 205 Covers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 206 Trays and bins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 207 External covers and panels . . . . . . . . . . . . . . . . . . . . 209 Document scanner assemblies . . . . . . . . . . . . . . . . . . . . . . 210 Document scanner assemblies . . . . . . . . . . . . . . . . . 211 Document feeder . . . . . . . . . . . . . . . . . . . . . . . . . . . . 213 Upper guide assembly . . . . . . . . . . . . . . . . . . . . . . . . 215 Internal assemblies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 216 Internal components (1 of 4). . . . . . . . . . . . . . . . . . . . 217 Internal components (2 of 4). . . . . . . . . . . . . . . . . . . . 219 Internal components (3 of 4). . . . . . . . . . . . . . . . . . . . 221 Internal components (4 of 4). . . . . . . . . . . . . . . . . . . . 223 Feeder assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . 225 Electrical components . . . . . . . . . . . . . . . . . . . . . . . . 227 Alphabetical parts list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 228 Numerical parts list. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 233
EN
Table 19. Authorized parts resellers in the United States Company name and address Contact information
Computer Parts Unlimited Inc. 3949 Heritage Oak Court Simi Valley, CA 93063 CHA (C. Hoelzle Associates) 17321 Eastman Street, Irvine, CA 92614-5523 Copylite Products Corp. New Town Commerce Centre, 4061 SW 47th Avenue Fort Lauderdale, FL 33314 Parts Now! Inc. Headquarters 3517 W. Beltline Hwy. Madison, WI 53713 Southeast Office 1085 SW 15th Ave. #5 Delray Beach, FL 33444 The Printer Works, Inc. 3481 Arden Road Hayward, CA 94545 Vance Baldwin Electronics 2701 West McNab Road Pompano Beach, FL 33069 Phone: 805-306-2500 Fax: 805-306-2597 Toll free: 800-817-5957 Phone: (949) 251-9000 Toll free: 800-959-9601 Phone: (954) 581-2470
URL
www.cpumart.com
www.chainc.com
Phone: 608-276-8688 Fax: 608-276-9593 Toll free 800-886-6688 Phone: 561-279-9280 FAX: 561-279-9122 Toll free 800-RG1-0939 (800) 832-1400
www.partsnowinc.com
www.PrinterWorks.com
Note
The companies listed in table 19 are current as of the publication date of this manual. Updated lists are available at the following website: http://www.hp.com/ssg/parts/direct_order.html
EN
Consumables
HP LaserJet 3200 product consumables are listed in chapter 3, Maintenance, in table 9 on page 52. Consumables are available directly from Hewlett-Packard at (800) 538-8787. Contact your local HP Parts Coordinator for other local phone numbers.
EN
Accessories
Table 21. Accessories Item
Dual in-line memory modules (DIMM)
Description
8 MB 16 MB 32 MB 64 MB
Part number
C4141A C4142A C4143A C3913A C4092A C2946A
Toner cartridge Cables and interface accessories 3-meter size C IEEE-1284 parallel cable 10-meter size C IEEE1284 parallel cable USB cable Power cable Telephone cable HP JetDirect Print Servers 70X 170X 300X 500X (for a Token Ring network connection) 500X (for a BNC, 10Base-T, or 10/ 100Base-TX network connection)
J3265
EN
EN
Common hardware
Screw, star
Screw, self-tapping
EN
Assembly locations
Feed assembly
Electrical components
Figure 83.
EN
Covers
Figure 84.
Part number
RB2-5407-000CN RB2-5412-000CN RB2-5423-000CN RB2-5437-000CN RB2-5471-000CN RB2-5493-000CN
Description
Support extension, document output Support, document output Support, paper output Support, document feeder Overlay (speed-dial template) Support, paper input
EN
Covers 207
Figure 85.
Part number
RB2-5434-000CN RF5-3232-000CN RB2-5485-000CN RB2-5488-000CN RB2-5489-000CN RB2-5490-000CN XA9-0302-000CN
Description
Cover, face-up Cover, rear Cover, DIMM Cover, front Cover, top Cover, right Screw, TP, M3x8
RG5-4601-020CN Single-sheet input tray assembly RG5-5391-000CN Paper input tray assembly RB2-5491-000CN RB2-5498-000CN XB4-7401-209CN Cover, left Cover, blanking Screw, tapping, truss head, M4X12
EN
Covers 209
29
Figure 86.
Part number
RB2-3354-000CN RB2-5405-000CN RB2-5406-000CN RB2-5410-000CN RF5-3236-000CN XA9-0267-000CN XA9-0591-000CN XA9-0779-000CN XA9-0870-000CN
Description
Strap, plastic Guide, document scanner Cover, cable Cover, contact image sensor Cable, flat Screw, TP, M3X6 Screw, M3X8 Screw, w/washer, M3X6 Screw, M4X10
RG5-5405-000CN Cable, flat RG5-5410-000CN Contact image sensor assembly RB2-5498-000CN RB2-5388-000CN RB2-4006-000CN RB2-5421-000CN RS6-2276-000CN C4262A XB4-7401-007CN XB4-7300-807CN Cover, blanking Plate, shield Deflector Guide, paper delivery Spring, torsion Control panel PCB Screw, tapping, pan head, M4X10 Screw, tapping, truss, head, M3X8
EN
Figure 87.
Document feeder
EN
Document feeder
Table 26. Document feeder Reference
1 2 3 4 5 6 501
Part number
HS5-0250-000CN HS5-0253-000CN XA9-0591-000CN XA9-0870-000CN
Description
Gear, 82T Gear, 21T/28T Screw, M3X8 Screw, M4X10
RG5-5400-000CN Motor assembly RG5-5401-000CN Pickup roller assembly XB2-8301-007CN Screw, w/washer, M3X10
EN
Figure 88.
Part number
HB1-3035-000CN XB4-7401-007CN
Description
Separation pad Screw, tapping, pan head, M4X10
EN
Internal assemblies
24
Figure 89.
Internal components (1 of 4)
EN
Internal components (1 of 4)
Table 28. Internal components (1 of 4) Reference
1 2 3 5 6 7 8 9 10 10A 11 12 14 15 16 17 18 19 21 22 22A 23 24
Part number
RB2-4324-000CN RB2-4017-000CN RB2-4030-000CN RB2-3951-000CN RB2-3952-000CN RB2-3953-000CN RB2-4054-000CN RB2-4055-000CN RH7-1404-000CN RB2-3959-000CN RB2-4329-000CN RY7-5051-000CN RB2-5497-000CN XA9-0779-000CN RB2-4042-000CN RB9-0538-000CN RF5-2880-000CN
Description
Sheet Cable holder Scanner cable cover Static charge eliminator Spring, torsion Spring, torsion Sheet, transfer Safety cover Motor, stepping Spring, leaf, left Seal, frame, 2 Clutch kit Hinge clip Screw, w/washer, M3X6 Spring, torsion Plate, grounding Holder, fixing
RG5-5393-000CN Formatter case assembly RG5-5392-000CN Hinge support assembly XB4-7401-007CN C7052-60004 C4261A Screw, tapping, pan head, M4X10 Line interface unit (LIU) Formatter (not pictured; see figure 64 on page 138) Screw, tapping, pan head, M4X10 RG5-4617-000CN Sensor cable
501
XB4-7401-007CN
EN
Figure 90.
Internal components (2 of 4)
EN
Internal components (2 of 4)
Table 29. Internal components (2 of 4) Reference
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 501 502
Part number
RB2-3930-000CN
Description
Shaft, pickup roller
RG5-4584-000CN Roller holder assembly RG5-4585-020CN Gear assembly RG5-5421-000CN Laser/scanner assembly RB2-3943-000CN RB2-3944-000CN RB2-3945-000CN RB2-3949-000CN RB2-3931-000CN RB2-3904-000CN RB2-4026-000CN XA9-0267-000CN XA9-0653-000CN RB2-5501-000CN RB2-5500-000CN XB4-7401-007CN XB6-7300-807CN Shaft Spring, leaf Foot Cam Roller Cover, foamy Roller, pickup Screw, TP, M3X6 Screw, w/star washer, M3X6 Sheet, light-blocking Sheet, light-blocking Screw Screw
EN
Figure 91.
Internal components (3 of 4)
EN
Internal components (3 of 4)
Table 30. Internal components (3 of 4) Reference
1 2 3 4 5 6 7 8 9 10 11 12 13 16
Part number
RB2-4219-000CN RB2-3947-000CN RF5-2832-000CN RB2-3960-000CN RB2-3961-000CN RF5-2818-000CN RF5-2819-000CN RF5-2822-000CN RF5-2830-000CN RS5-2502-000CN RB2-4016-020CN RY7-5049-000CN RS6-2122-000CN
Description
Plate, grounding Holder, pad Arm, pad Flag, sensor Spring, torsion Guide, cartridge, left Guide, cartridge, right Roller, face-up Roller, face-down Spring, compression Stop, slide Gear kit Spring, compression
EN
Figure 92.
Internal components (4 of 4)
EN
Internal components (4 of 4)
Table 31. Internal components (4 of 4) Reference
1 2 3 4 5 6 7 8 8A 8B 8C 8D 10 11 12 13 14 15 16 17 19 20 501 502 503
Part number
RY7-5050-020CN RB2-3939-020CN RB2-3940-000CN RB2-3950-000CN RB2-3956-000CN RB2-3957-060CN RB2-4222-000CN RB1-7286-000CN RB1-7287-000CN RB2-4223-000CN RF5-2823-020CN RH7-5227-000CN
Description
Subpad kit (includes left and right) Bushing, right Spring, compression Guide, transfer Bushing, left Bushing, right Roller, face up Spring, wire Spring, wire Roller, face down Roller, pressure Solenoid
Part of gear kit, part number RY7-5049-000CN on page 221. RG5-4657-020CN Transfer assembly RG5-4589-040CN Fusing element RG5-5387-000CN Metal clip, fusing element (left) RB2-3958-030CN RY7-5060-000CN RB2-4432-000CN RB2-4431-000CN XB4-7400-805CN XB4-7401-209CN XB4-7401-007CN Guide, fusing element Screw kit, delivery assembly Sub guide, right Sub guide, left Screw, tapping, truss head, M4x Screw, tapping, truss head, M4x12 Screw, tapping, pan head, M4X10
EN
Figure 93.
Feeder assembly
EN
Feeder assembly
Table 32. Feeder assembly Reference Part number Description
EN
15
Figure 94.
Electrical components
EN
Electrical components
Table 33. Electrical components Reference
1 2 3 7 8 9 10 11 12 13 14 15
Part number
RB1-7303-000CN RB2-3984-000CN RB2-3985-000CN RH2-5381-000CN VS1-5057-002CN XA9-0653-000CN XA9-0951-000CN RB2-4049-000CN RB2-4327-000CN RB2-4328-000CN
Description
Spacer ECU pan Sheet, insulating Cable, flat Connector, 2P Screw, w/star washer, M3X6 Screw, w/washer, M3X8 Plate, grounding Seal, sensor, 1 Seal, sensor, 2
RG5-5395-000CN ECU
EN
Part number
RF5-2832-000CN RB2-3956-000CN RB2-3939-020CN RB2-3957-060CN RB2-4017-000CN WT2-0307-000CN RF5-3236-000CN RG5-5405-000CN RH2-5381-000CN RB2-3949-000CN RY7-5051-000CN VS1-5057-002CN RG5-5410-000CN C4262A RB2-5498-000CN RB2-5498-000CN RB2-5406-000CN RB2-5410-000CN RB2-5485-000CN RB2-5434-000CN RB2-3904-000CN RB2-5488-000CN RB2-5491-000CN RF5-3232-000CN RB2-5490-000CN RB2-5489-000CN RB2-4006-000CN RG5-5412-000CN RG5-4593-000CN RG5-4599-030CN RG5-4586-000CN RG5-5395-000CN
Ref.
4 6 3 7 2 14 13 19 7 8 14 8 20 29 22 22 11 12 2A 1 10 3 21 2 5 4 25 24 8 9 10 15
Figure
91 92 92 92 89 86 86 86 94 90 89 94 86 86 85 86 86 86 85 85 90 85 85 85 85 85 86 86 92 94 89 94
EN
Part number
RB2-3984-000CN RG5-4581-000CN RB2-3960-000CN RB2-3945-000CN C4261A RG5-5393-000CN RG5-4589-040CN (see gear kit) RG5-4585-020CN RY7-5049-000CN HS5-0253-000CN HS5-0250-000CN RF5-2818-000CN RF5-2819-000CN RB2-5405-000CN RB2-3958-030CN RB2-5421-000CN RB2-3950-000CN RB2-5497-000CN RG5-5392-000CN RF5-2880-000CN RB2-3947-000CN RG5-5464-000CN RG5-5421-000CN C7052-60004 RG5-5387-000CN RG5-5388-000CN RG5-5400-000CN RH7-1404-000CN RB2-5471-000CN RG5-4582-060CN RG5-5391-000CN RG5-5401-000CN RB9-0538-000CN RB2-4219-000CN
Ref.
2 5 7 21 14 12 3 13 2 1 7 8 10 16 26 5 15 22 19 3 28 4 24 15 2 5 10A 5 1 8 6 18 2
Figure
94 93 91 90 89 89 92 92 90 91 87 87 91 91 86 92 86 92 89 89 89 91 86 90 89 92 92 87 89 84 91 85 87 89 91
EN
Part number
RB2-4049-000CN RB2-5388-000CN RB2-3931-000CN RG5-4584-000CN RB2-4223-000CN RB2-4222-000CN RF5-2830-000CN RF5-2822-000CN RB2-4026-000CN RF5-2823-020CN RB2-4055-000CN RG5-5415-000CN RB2-4030-000CN XB4-7401-007CN XB6-7300-807CN RY7-5060-000CN XA9-0591-000CN XA9-0591-000CN XA9-0870-000CN XA9-0870-000CN XB4-7401-007CN XB4-7401-007CN XB4-7401-007CN XB4-7401-007CN XB4-7401-007CN XB4-7400-805CN XB4-7401-209CN XB4-7401-209CN XB4-7300-807CN XA9-0267-000CN XA9-0267-000CN XA9-0302-000CN XA9-0653-000CN XA9-0653-000CN XB2-8301-007CN
Ref.
12 23 9 1 8D 8A 10 9 11 10 9 13 3 501 502 17 16 3 18 4 502 501 501 22A 503 501 502 501 503 15 12 6 14 10 501
Figure
94 86 90 90 92 92 91 91 90 92 89 90 89 90 90 92 86 87 86 87 86 88 89 89 92 92 92 85 86 86 90 85 90 94 87
EN
Part number
XA9-0779-000CN XA9-0779-000CN XA9-0951-000CN RB2-4329-000CN RB2-4327-000CN RB2-4328-000CN RG5-4617-000CN RG5-5404-000CN HB1-3035-000CN RB2-3943-000CN RB2-3930-000CN RB2-4324-000CN RB2-3985-000CN RB2-5501-000CN RB2-5500-000CN RB2-4054-000CN RG5-4601-020CN RH7-5227-000CN RB1-7303-000CN RS5-2502-000CN RS6-2122-000CN RB2-3940-000CN RB2-3944-000CN RB2-3959-000CN RS6-2276-000CN RB2-3952-000CN RB2-3953-000CN RB2-4042-000CN RB2-3961-000CN RB1-7286-000CN RB1-7287-000CN RB2-3951-000CN RB2-4016-020CN RB2-3354-000CN RB2-4431-000CN
Ref.
17 16 11 12 13 14 23 1 1A 5 2 1 3 15 16 8 7 11 1 11 16 4 6 11 27 6 7 17 6 8B 8C 5 12 9 20
Figure
86 89 94 89 94 94 89 88 88 90 90 89 94 90 90 89 85 92 94 91 91 92 90 89 86 89 89 89 91 92 92 89 91 86 92
EN
Part number
RB2-4432-000CN RY7-5050-020CN RB2-5407-000CN RB2-5437-000CN RB2-5412-000CN RB2-5493-000CN RB2-5423-000CN RG5-4657-020CN
Ref.
19 1 1 4 2 6 3 13
Figure
92 92 84 84 84 84 84 92
EN
Description
Formatter Control panel PCB Line interface unit (LIU) Separation pad Gear, 82T Gear, 21T/28T Spring, wire Spring, wire Spacer Strap, plastic Cover, foamy Shaft, pickup roller Roller Bushing, right Spring, compression Shaft Spring, leaf Foot Holder, pad Cam Guide, transfer Static charge eliminator Spring, torsion Spring, torsion Bushing, left Bushing, right Guide, fusing element Spring, leaf, left Flag, sensor Spring, torsion ECU pan Sheet, insulating
Ref.
29 24 1A 1 2 8B 8C 1 9 10 2 9 3 4 5 6 7 3 8 5 5 6 7 6 7 16 11 5 6 2 3
Figure
89 86 89 88 87 87 92 92 94 86 90 90 90 92 92 90 90 90 91 90 92 89 89 89 92 92 92 89 91 91 94 94
Description
Deflector Stop, slide Cable holder Roller, pickup Scanner cable cover Spring, torsion Plate, grounding Sheet, transfer Safety cover Plate, grounding Roller, face up Roller, face down Sheet Seal, sensor, 1 Seal, sensor, 2 Seal, frame, 2 Sub guide, left Sub guide, right Plate, shield Guide, document scanner Cover, cable Support extension, document output Cover, contact image sensor Support, document output Guide, paper delivery Support, paper output Cover, face-up Support, document feeder Overlay (speed-dial template) Cover, DIMM Cover, front Cover, top Cover, right Cover, left Support, paper input
Ref.
25 12 2 11 3 17 12 8 9 2 8A 8D 1 13 14 12 20 19 23 10 11 1 12 2 26 3 1 4 5 2A 3 4 5 21 6
Figure
86 91 89 90 89 89 94 89 89 91 92 92 89 94 94 89 92 92 86 86 86 84 86 84 86 84 85 84 84 85 85 85 85 85 84
EN
Description
Hinge clip Cover, blanking Cover, blanking Sheet, light-blocking Sheet, light-blocking Plate, grounding Guide, cartridge, left Guide, cartridge, right Roller, face-up Roller, pressure Roller, face-down Arm, pad Holder, fixing Cover, rear Cable, flat Feeder assembly Paper guide plate assembly Roller holder assembly Gear assembly Drive assembly Fusing element Delivery assembly Door sensor assembly Single-sheet input tray assembly Sensor cable Transfer assembly Metal clip, fusing element (left) Metal clip, fusing element (right) Paper input tray assembly Hinge support assembly Formatter case assembly ECU Motor assembly Pickup roller assembly Separation assembly
Ref.
15 22 22 16 15 18 7 8 9 10 10 4 19 2 13 1 1 3 10 14 8 9 7 23 13 15 2 8 22 21 15 5 6 1
Figure
89 85 86 90 90 89 91 91 91 92 91 91 89 85 86 93 91 90 90 89 92 92 94 85 89 92 92 92 85 89 89 94 87 87 88
EN
Description
Cable, flat Contact image sensor assembly Deflector link assembly Scanner cable Laser/scanner assembly Image scanner sensor, PCB assembly Cable, flat Motor, stepping Solenoid Spring, compression Spring, compression Spring, torsion Gear kit Subpad kit (includes left and right) Clutch kit Screw kit, delivery assembly Connector, 2P Cable tie Screw, TP, M3X6 Screw, TP, M3X6 Screw, TP, M3x8 Screw, M3X8 Screw, M3X8 Screw, w/star washer, M3X6 Screw, w/star washer, M3X6 Screw, w/washer, M3X6 Screw, w/washer, M3X6 Screw, M4X10 Screw, M4X10 Screw, w/washer, M3X8 Screw, w/washer, M3X10 Screw, tapping, truss, head, M3X8 Screw, tapping, truss head, M4x Screw, tapping, pan head, M4X10 Screw, tapping, pan head, M4X10
Ref.
19 20 24 13 4 28 7 10A 11 11 16 27 13 1 14 17 8 14 15 12 6 16 3 14 10 17 16 18 4 11 501 503 501 502 501
Figure
86 86 86 90 90 86 94 89 92 91 91 86 91 92 89 92 94 86 86 90 85 86 87 90 94 86 89 86 87 94 87 86 92 86 88
EN
Description
Screw, tapping, pan head, M4X10 Screw, tapping, pan head, M4X10 Screw Screw, tapping, pan head, M4X10 Screw, tapping, truss head, M4X12 Screw, tapping, truss head, M4x12 Screw
Ref.
501 22A 501 503 501 502 502
Figure
89 89 90 92 85 92 90
EN
EN
Index
A
abbreviations, fax 187 AC power distribution 72 accessories, ordering 202 acoustical emissions 18 adding paper 48 ADF (automatic document feeder) capacity 14 adjusting fax data store parameters 175 alcohol, cleaning with 57, 58 alignment, troubleshooting 162 alphabetical part number list 228 ammonia, avoiding 53 appropriate responses, fax 186 arrays, optical system 63 arrow keys 31 automatic document feeder (ADF) capacity 14 capacity ADF (automatic document feeder) 14 circuit 17 input trays 14 memory slots 15 output trays 14 carrier sheets 46 cartridges. See toner cartridges central processing unit. See CPU characters, troubleshooting 160, 161 charge eliminator 75 charging, image formation 75 checks drum rotation 169 engine 167 half self-test functional 168 heating element 170 high-voltage power supply 171 paper path 173 toner cartridge connection points 171 circuit capacity 17 cleaning alcohol 57, 58 image formation processes 76 precautions 53 print path 54 scanner path 57 toner 55 Clear key 32 clips, fusing element 120 clothing, washing toner off 55 commands, PJL 178 complex pages, detecting 67 compliance information 25 conditioning stage 75 configuration report, printing 181 conformity, declaration of 25 connection points, testing 171 connectors, identifying 22 consumables life expectancies 52 ordering 201 contact glass 63 contact image sensor (CIS) operations 63 removing 103 continuous self-test 174
B
back arrow key 31 back cover, removing 90 Back space key 31 background scatter, troubleshooting 161 beam detect (BD) signal 75 beam, laser 75 bias 75 bidirectional communications 66, 67 billing log 182 bins. See output bin; input trays black dots, troubleshooting 158 black pages, troubleshooting 161 blade, cleaning 76 blank pages, troubleshooting 162 block fax list 182 boards ECU 140 scanner 112 breaking paper 165 business cards, loading 47 buttons, control panel 31 buying. See ordering
C
cables part numbers 202 power, identifying 22 calibrating scanner 59, 192
EN
contrast key 32 troubleshooting 157 control panel error messages 35 keys 31 lights 31 menu structure 33 release door 20 removing 112 reports, printing 181 troubleshooting 146 using 33 Copy key 32 copy setup menu 34 copying loading media 45 selecting media 44 speed 17 troubleshooting 147 covers, removing back 90 left side 93 part numbers 209 right side 91 top 95 tray kits 206 CPU 65 crooked images, troubleshooting 164 curl, paper maximum 170 troubleshooting 164
D
darkness. See contrast data Page Protect 67 sending to formatter 65 storing 66 data store report 174 date menu 34 DBM 190 DC power distribution 72 declaration of conformity 25 default settings 178 defect ruler 191 delivery assembly, removing 116 delivery delay jam 79 delivery rollers life expectancy 52 testing 173 delivery stationary jam 79 demonstration page, printing 181 depth 16
developers menu 175 developing stage 75 diagnostic mode 176 diagnostics. See checks dimensions 16, 30 DIMMs part numbers 202 removing 89 slots 15 diodes, operations 63 display, control panel 31 document feeder tray identifying 21 loading 45 part numbers 213 document output slot, identifying 20 document release door, identifying 20 document scanner assemblies part numbers 210 removing 100 document scanner motor, removing 107 document scanner pickup roller life expectancy 52 removing 105 document scanner rollers, life expectancies 52 document scanner separation pad life expectancy 52 removing 106 document sensor (PS1) 81 documentation, ordering 200 doors cleaning 53 document release 20 front paper path 20, 50 identifying 20 memory 22 open sensor (SW301) 80, 173 printer, identifying 20 printer, removing 96 DOS, PJL commands 180 dots per inch (dpi). See resolution dots, troubleshooting 158 draft mode 66 DRAM, formatter 65 drive roller, testing 173 dropouts, troubleshooting 161 drum cleaning stage 76 drums operations 74, 75 testing 169 duty cycle product 15 toner cartridges 26
EN
E
EconoMode 66 ECP interface 65 ECU (Engine Control Unit) formatter to printer operations 82 image formation process 75 motor 71 operations 69 pan, removing 139 paper feeding operations 77 power system 72 replacing 140 troubleshooting 147 edges not printing 157 electrical components, part numbers 227 electrical shocks, avoiding 53 electrical specifications 17 electrostatic discharge (ESD) 87 eliminator, static charge 75 emissions acoustical 18 energy consumption 17 Engine Control Unit (ECU) formatter to printer operations 82 image formation process 75 motor 71 operations 69 pan, removing 139 paper feeding operations 77 power system 72 replacing 140 troubleshooting 147 engine test switch (SW201) 80, 167 Enhanced I/O 66 Enlarge key 32 Enter/Menu 31 envelopes printing 49 selecting 43 environmental specifications 16, 30 Error light 31 error messages 35 exchange program, parts 202 exit sensor (PS201) 77, 81 exit sensor flag, removing 118 Extended Capabilities Port (ECP) interface 65
F
faded print, troubleshooting 158 fans 15 fasteners 204 fax abbreviations 187 appropriate responses 186 phase sequence 185 fax activity report 182 EN
fax data store parameters 175 fax functions menu 34 fax setup menu 34 fax trace report 183 Fax/Send key 32 faxing loading media 45 resolution 17 selecting media 44 T.30 protocol trace report 183 features 14 feed assembly drive roller operations 77 removing 141 feed roller, life expectancy 52 feeder tray identifying 21 loading 45 part numbers 213 feeding operations, printer 77 feeding problems, troubleshooting 164 See also jams field replaceable units (FRUs) 87 fine resolution 17 firmware 15 version 176 first-page out 14 flags, exit sensor 118 flat-blade screwdrivers 87 formatter CPU 65 memory 65 operations 65 Page Protect feature 67 pan, removing 137 printer operations 82 removing 138 voltage 72 forms, multipart 43 forward arrow key 31 frequent jams, troubleshooting 165 front paper output slot 50 front paper path door identifying 20 using 50 FRUs (field replaceable units) 87 functional check, half self-test 168 fuser operations 76 fuser roller, testing 173 fuses 72 fusing element life expectancy 52 removing 119 testing 170
G
gear train motor, removing 124 glossy paper 44 graph, calibration 192 group dial report 182 guides, removing internal 94 upper assembly 108
internal paper guide, removing 94 INTR (Initial Rotation Period) 82 isopropyl alcohol, cleaning with 57
J
jams feeding problems, troubleshooting 164 frequent 165 preventing 44, 48 sensors 79 JetDirect print servers, ordering 202
H
half self-test functional check 168 halftone resolution 17 hardware capabilities 14 headers, fax menu 34 heating element life expectancy 52 removing 119 testing 170 height 16 high-voltage power supply power distribution 73 testing 171, 172 voltage 72 horizontal orientation 48 horizontal streaks, troubleshooting 160 HP JetDirect print servers, ordering 202 HP LaserJet paper 43 HP Multipurpose paper 43 humidity 16
K
keypad, one-touch 32 keys, control panel 31 kick plate operations 77 removing 134 testing 173 kits, tray 206
L
labels 44 landscape orientation 48 laser beam, operations 75 Laser/Beam Detect Circuitry voltage 72 laser/scanner assembly removing 113 service precautions 87 LaserJet paper 43 latches, printer door release 20 LCD test 176 leading edge, detecting 77 LED test 176 LEDs, operations 63 left side cover, removing 93 lenses 75 letterhead, printing 49 lever, special media identifying 21 using 47 life expectancies, consumables 52 light-emitting diodes (LEDs), operations 63 lightness. See contrast lights, control panel 31 lightweight media loading 46 troubleshooting 166 lines, troubleshooting black 159 calibration graph 192 white 158 LIU (line interface unit) removing 138
I
I/O, Enhanced 66 image formation operations 74 Page Protect 67 image quality, troubleshooting 157 initial residual paper jam 79 initializing 178 ink cartridges. See toner cartridges input trays capacity 14 feeding operations 77 identifying 21 loading 45, 48 media sizes 43 inserting media normal 45 paper input tray 48 special 46 installation requirements 30 interfaces, formatter 66 internal assemblies diagrams and part numbers 216 removing 113
EN
loading media normal 45 paper input tray 48 special 46 long pages, troubleshooting 164 LPT ports, troubleshooting 148 LSTR (Last Rotation Period) 82
N
needle nose pliers 87 negative charge 75 network accessories, ordering 202 newspaper clippings 46 noise 18 numbers See also phone numbers model 19 part 228, 233 serial 19 numeric keys 32 numerical list, part numbers 233 NVRAM init 178 NVRAM variables 178 NVRAM, formatter 65
M
magnetic screwdrivers 87 maintenance cleaning 53 consumables, life expectancies 52 recalibrating scanner 59 manual feed 49 margins, minimum 157 media lightweight 46, 166 loading 45 selecting 43, 44 special, loading 46 media jams. See jams media lever, special identifying 21 using 47 memory door, identifying 22 Enhanced I/O 66 formatter 65 removing 89 slots 15 Memory Enhancement technology (MEt) 66 menu developers 175 secondary service 174 menu structure entering 31 printing 33 using 33 messages, error 35 MEt (Memory Enhancement technology) 66 metal clips, fusing element 120 mirrors 75 misaligned print, troubleshooting 162 model numbers 19 motors gear train, removing 124 scanner, removing 107 testing 173 voltage 72 multifeeds, troubleshooting 165 See also jams multipart forms 43 Multipurpose paper 43
O
one-touch keypad 32 one-touch report 182 online support. See web sites operating environment 16, 30 operations Engine Control Unit (ECU) 69 formatter system 65 formatter to printer sequence 82 image formation system 74 optical system 63 paper feed system 77 printer 68 testing 168 optical system, operations 63 ordering accessories 202 consumables 201 documentation 200 parts 200 orientation, landscape 48 output bin, identifying 21 output path, selecting 50 output roller, removing 114 output slot identifying 20 using 50 overcurrent protection 72 overriding switches 173 overvoltage protection 72
P
Page Protect 67 pans, removing ECU 139 formatter 137
EN
paper breaking 165 curl 164, 170 feeding operations 77 LaserJet 43 lightweight 46, 166 loading 45 Multipurpose 43 selecting 43, 44 slick 44 special, loading 46 paper exit sensor (PS201) 77, 81 paper exit sensor flag, removing 118 paper feed assembly, removing 141 paper feeding problems, troubleshooting 164 paper guides, internal 94 paper input tray feeding operations 77 identifying 21 loading 48 media sizes 43 troubleshooting 165 paper jams. See jams paper out sensor (PS001) 81 paper output bin, identifying 21 paper path diagrams 78 testing 173 troubleshooting 181 paper path door, identifying 20 paper pick-up assembly, removing 132 paper pickup roller operations 77 testing 173 paper top sensor (PS002) 77, 80 parallel cable connector 22 parallel ports, troubleshooting 148 parameters 175 part numbers alphabetical list 228 numerical list 233 subassemblies 203 parts ordering 200 remanufactured 202 removing and replacing 87 paths output, selecting 50 paper 78, 173, 181 print, cleaning 54 scanner, cleaning 57 PCL (Printer Command Language) 67 perforated papers 44 phase sequence, fax 185 Phillips screwdrivers 87 phone line connectors 22
phone numbers compliance information 25 ordering consumables 201 phonebook report 182 photo resolution 17 photographs 46 photosensitive drum operations 74, 75 testing 169 phototransistor array 63 pick-up assembly, removing 132 pickup delay jam 79 pickup roller cleaning 56 life expectancy 52 operations 77 removing 105, 131 testing 173 pickup solenoid (SL001) 77, 80 pickup stationary jam 79 PJL (Printer Job Language) 67, 178 pliers 87 ports, troubleshooting LPT 148 parallel 148 Posidrive screwdrivers, avoiding 87 positive charge 75 power consumption 17 Engine Control Unit (ECU) 72 requirements 17 troubleshooting 146 power cable connectors 22 power supplies disconnecting 87 high-voltage 72, 73 testing 171 pressure roller life expectancy 52 operations 76 removing 128 preventing jams 44, 48 primary charging stage 75 PRINT 82 print cartridges. See toner cartridges print path, cleaning 54 print servers, ordering 202 printer block diagram 68 Engine Control Unit (ECU) 69 formatter operations 82 Printer Command Language (PCL) 67 printer door cleaning 53 identifying 20 removing 96
EN
Printer Job Language (PJL) 67, 178 printer pickup roller cleaning 56 life expectancy 52 operations 77 removing 131 printer separation pad life expectancy 52 operations 77 printer subpads life expectancy 52 printer transfer roller, life expectancy 52 printing complex pages, Page Protect 67 feeding operations 77 image formation operations 74 letterhead 49 loading media 48 resolution 17 selecting media 43 skew specifications 18 speed 17 troubleshooting 148 product overview 14 protocol trace report, printing 183 PS001 (paper out sensor) 81 PS002 (paper top sensor) 77, 80 PS1 (document sensor) 81 PS201 (paper exit sensor) 77, 81 purchasing. See ordering
secondary service 174 T.30 protocol trace 183 translation 174 reset 178 resistance, heating element 170 resolution key 32 maximum 17 right side cover, removing 91 rod lens array 63 rollers life expectancies 52 output, removing 114 pickup, removing 105, 131 pressure, removing 128 testing 173 transfer, removing 130 ruler, repetitive image defect 191
S
Scan key 32 scanline data 174 scanner document path 64 recalibrating 59, 192 scanner assemblies part numbers 210 removing 100 scanner board, removing 112 scanner motor, removing 107 scanner path, cleaning 57 scanner pickup roller life expectancy 52 removing 105 scanner rollers, life expectancies 52 scanner separation pad life expectancy 52 removing 106 scanning image quality, troubleshooting 163 loading media 45 operations 63 resolution 17 selecting media 44 skew specifications 18 troubleshooting 148 scanning exposure stage 75 scattered background, troubleshooting 161 screwdrivers 87 screws self-tapping 87 types of 204 sealing tape removing 168 secondary service menu 174 selecting media 43
Q
quality, troubleshooting 157
R
RAM. See memory Ready light 31 recalibrating scanner 59, 192 receipts 46 Redial/Pause key 32 redistributing toner 156 Reduce/Enlarge key 32 refilled toner cartridges 26 release latches, printer door 20 remanufactured parts 202 removing parts 87 repetitive image defect ruler 191 replacing consumables 52 parts 87 reports continuous self-test 174 data store 174 fax trace 183 menu 34 printing 181, 182 EN
self test continuous 174 self-tapping screws, installing 87 self-tests. See checks sensors contact image (CIS), operations 63 contact image (CIS), removing 103 exit flag, removing 118 feeding operations 77 jam detection 79 operations 80 separation pads life expectancies 52 operations 77 removing 106, 135 separation process 75 serial numbers 19 service menu 34 service mode 178 settings isolation, PJL 67 NVRAM variables 178 sheet metal, precautions 87 shock hazards 53 side covers, removing left 93 right 91 signals, beam detect (BD) 75 single-sheet input slot feeding operations 77 identifying 21 media sizes 43 troubleshooting 165 using 49 sizes, media 43, 44 skew specifications 18 troubleshooting 162 SL001 (pickup solenoid) 77, 80 slick papers 44 slots, memory 15 smears, troubleshooting 159, 160 smudges, troubleshooting 158 software installation, troubleshooting 148 ordering 200 solenoids operations 77, 80 removing 127 testing 173 voltage 72 sound emissions 18 space requirements 30 spare parts. See parts; consumables
special media lever identifying 21 using 47 special media, loading 46 specifications 16 speed copying 17 first-page out 14 printing 17 speed dial report 182 Speed-Dial key 32 spring mechanism, paper exit sensor flag 118 stains, troubleshooting 158 standard resolution 17 star screws 204 static charge eliminator 75 static discharge precautions 87 STBY (Standby) 82 Stop/Clear key 32 storing data 66 product 16 streaks, troubleshooting 158, 159, 160 stripes, troubleshooting 158 subpads life expectancies 52 superfine resolution 17 supplies life expectancies 52 ordering 201 SW201 (engine test switch) 80, 167 SW301 (door open sensor) 80, 173 switches door open (SW301) 80, 173 engine test (SW201) 80, 167 overriding 173 system reset 178
T
T.30 protocol trace report, printing 183 tape, removing 168 technical support web sites 201 temperature 16 tests. See checks text, troubleshooting 160, 161 theory of operations. See operations thermistor connector 170 time/date, header menu 34 toner fusing process 76 redistributing 156 saving 66 washing off clothing 55 waste, cleaning operations 76
EN
toner cartridges connection points, testing 171 defects, checking for 156 life expectancy 52 operations 74 recycling 26 redistributing 156 refilled 26 removing 87 sealing tape, removing 168 tools, required 87 top cover, removing 95 trace report, printing 183 trailing edge, detecting 79 train motor, gear 124 transfer roller cleaning 53 life expectancy 52 removing 130 testing 173 transfer stage 75 translations report 174 tray kits 206 trays. See input trays troubleshooting control panel 146 copying 147 ECU (Engine Control Unit) 147 feeding problems 164 half self-test functional test 168 image quality 157 LPT ports 148 power 146 printing 148 recalibrating scanner 192 repetitive image defect ruler 191 scanning 148 software installation 148 truss head screws 204
V
vacuuming, avoiding 55 variables, NVRAM 178 version,firmware 176 vertical streaks, troubleshooting 159 voids, troubleshooting 160 voltage Engine Control Unit (ECU) 72 overvoltage protection 72 part numbers 203 requirements 17 Volume key 32
W
WAIT 82 warranty product 23 waste toner, cleaning operations 76 web sites technical support 201 weight paper 50 product 16 white pages, troubleshooting 162 white streaks, troubleshooting 158 width 16 wiring diagram 194 wrapping jam 79 wrinkled pages, troubleshooting 164 writing stage 75
U
Universal Serial Bus. See USB unplugging 53, 87 upper guide assembly part numbers 214 removing 108 USB connector 22 operations 65
EN
EN
Copyright 2000 Hewlett-Packard Co. http://www.hp.com/support/lj3200 English Manual Part Number C7052-90923
*C7052-90923* *C7052-90923*
C7052-90923