Sbea139731 1
Sbea139731 1
Sbea139731 1
TITLE
ATA 00 – FORWARD CABIN ROOF CEILING HARNESS INSPECTION
REVISION LOG
First Issue.
An appropriate entry should be made in the aircraft log book upon accomplishment.
If ownership of aircraft has changed, please, forward to new owner.
Page 1 of 23
1. PLANNING INFORMATION
A. EFFECTIVITY
All AB/AW139 from S/N 31005 to S/N 31984 (except S/N 31007, S/N 31803,
S/N 31959, S/N 31967, S/N 31969, S/N 31974, S/N 31982 and S/N 31983), from
S/N 41001 to S/N 41580 and from S/N 41801 to S/N 41806.
B. COMPLIANCE
Part I:
Within and not later than ten (10) FH from the issue date of this Service Bulletin.
Part II:
Within and not later than twenty-five (25) FH from the issue date of this Service Bulletin.
C. CONCURRENT REQUIREMENTS
N.A.
D. REASON
This Service Bulletin is issued in order to prescribe one-off inspections of the Forward
Cabin Roof Ceiling Harnesses and their installation in the area between STA 3120 and
3900 to identify potential chafing conditions.
E. DESCRIPTION
Part I of this Service Bulletin is developed to prescribe a one-off inspection of the
Forward Cabin Roof Ceiling Harnesses installation in the area between STA 3120 and
3400 to verify the proper installation of the C/As in the area.
Part II of this Service Bulletin is developed to prescribe a one-off inspection of the
harness installation in the area between STA 3400 and 3900 where the diode A77 is
located.
F. APPROVAL
The technical content of this Service Bulletin is approved under the authority of DOA nr.
EASA.21.J.005. For helicopters registered under other Aviation Authorities, before
applying the Service Bulletin, applicable Aviation Authority approval must be checked
within Leonardo Helicopters customer portal.
EASA states mandatory compliance with inspections, modifications or technical
directives and related time of compliance by means of relevant Airworthiness Directives.
If an aircraft listed in the effectivity embodies a modification or repair not LH certified and
affecting the content of this Service Bulletin, it is responsibility of the Owner/Operator to
G. MANPOWER
To comply with this Service Bulletin, the following MMH are deemed necessary:
Part I: approximately two (2) MMH;
Part II: approximately ten (10) MMH;
MMH are based on hands-on time and can change with helicopter configuration,
personnel and facilities available.
I. REFERENCES
1) PUBLICATIONS
Following Data Modules refer to AMP:
DATA MODULE DESCRIPTION PART
DM01 39-A-00-20-00-00A-120A-A Helicopter on ground for a safe I, II
maintenance.
DM02 39-A-24-91-01-00A-520A-A Circuit breaker panel - Remove I
procedure
DM03 39-A-24-91-01-00A-720A-A Circuit breaker panel - Install I
procedure
Following Data Modules refer to CSRP:
DATA MODULE DESCRIPTION PART
DM04 CSRP-A-51-21-02-02A-257A-D Waterborne chromate free I
primer (AWMS28-002) - Paint
and apply marking
DM05 CSRP-A-51-21-06-00A-644A-D Chromate conversion I
treatments of aluminum alloys
– Chromate
3) ANNEX
N.A.
J. PUBLICATIONS AFFECTED
N.A.
A. REQUIRED MATERIALS
1) PARTS
PART I
# P/N ALTERNATIVE P/N DESCRIPTION Q.TY LVL NOTE LOG P/N
1 3P5315A12931 STRIP ASSY REF . (1) -
2 AW001CL504B-N6 Support 3 .. (1) -
3 MS21075L3N MS21075L3 Nut plate 2 .. (1) -
4 NAS1097AD3-3 Rivet 0.1 kg .. (1) -
5 NAS1720H5L2A Rivet 3 .. (1) -
6 3P5315A10531 STRIP ASSY REF . (1) -
7 AW001CL504B-N6 Support 3 .. (1) -
8 MS21075L3N MS21075L3 Nut plate 2 .. (1) -
9 MS20426AD3-3 Rivet 0.1 kg .. (1) -
10 NAS1720H5L2A Rivet 3 .. (1) -
PART II
N.A.
2) CONSUMABLES
The following consumable materials, or equivalent, are necessary to accomplish this
Service Bulletin:
# SPEC./LH CODE NUMBER DESCRIPTION Q.TY NOTE PART
Aluminium Sheet AL-ALY 2024,
11 Commercial AR (2) (3) I
AMS-QQ-A-250/5, thickness 0.81 mm
Refer also to AMDI for the consumable materials required to comply with the AMP DM
referenced in the accomplishment instructions.
3) LOGISTIC MATRIX
N.A.
NOTES
(1) The quantity of items to be ordered depends on the results of the inspection.
(2) Item to be procured as local supply.
(3) As alternative it is possible to use material AMS-QQ-A-250/4 and thickness 1.02
mm.
Refer also to ITEP for the special tools required to comply with the AMP DM referenced
in the accomplishment instructions.
GENERAL NOTES
a) Place an identification tag on all components that
are re-usable, including the attaching hardware that
has been removed to gain access to the modification
area and adequately protect them until their later re-
use.
b) Shape the cables in order to prevent interference
with the structure and the other existing installations,
using where necessary suitable lacing cords and
plastic cable tiedown.
c) Let adhesive cure at room temperature for at least
24 hours.
d) All lengths are in mm.
PART I
1. In accordance with AMP DM 39-A-00-20-00-00A-120A-A, prepare the helicopter on
ground for a safe maintenance. Disconnect the battery, all electrical power sources and/or
the external power supply.
2. With reference to Figure 1 thru Figure 5 perform the inspection of the Forward Cabin Roof
Ceiling Harnesses and installation in the area between STA 3120 and 3400 as described
in the following procedure:
2.1 With reference to Figure 1 thru Figure 5, perform a visual inspection of the harness
installation on strips P/N 3P5315A10531 and 3P5315A12931 according to the
following steps:
2.1.1 In accordance with the applicable steps of AMP
DM 39-A-24-91-01-00A-520A-A and with reference to Figure 1, open the
circuit breaker panel assy without removing it.
2.1.2 With reference to Figure 1, insert the borescope inside the lightening
holes showed to access the area of the inspection.
2.1.3 Perform a visual inspection of the C/As installation.
NOTE
Perform step 3 only in case the C/As are installed as per
step 2.1.4.
3. In accordance with AMP DM 39-A-06-41-00-00A-010A-A and with reference to Figure 1
thru 5, remove all external panels, internal panels and internal liners as required to gain
access to the area affected by the installation and perform visual inspection of the C/As
and of the Torque Tube C3 and the strip installation adjustment as described in the
following procedure:
3.1 With reference to Figure 2 and Figure 3, perform a visual inspection of the C/As
fixed to strips P/N 3P5315A10531 and 3P5315A12931 according to the following
steps:
3.1.1 Check for chafing and/or damage of the cable harness.
3.1.2 In case of any finding, contact Product Support Engineering
([email protected]) in order to receive further
instruction.
3.2 With reference to Figure 2, perform a visual inspection of the Torque Tube C3
P/N 3E6711A00433. Make sure that there is no damage on the tube.
If damage is found, contact Product Support Engineering
([email protected]) in order to receive further instruction.
3.3 With reference to Figure 4 and to Figure 6 thru 9 perform strip installation
adjustment as described in the following procedure:
3.3.1 With reference to Figure 4, remove C/A from supports
AW001CL504B-N6 installed on strips P/N 3P5315A10531 and/or
P/N 3P5315A12931.
3.3.2 With reference to Figure 6 remove strips P/N 3P5315A10531 and/or
3P5315A12931 and put them on a workbench. Retain the fixing
hardware for later use.
NOTE
Perform Steps 3.3.4 ONLY in case of damage of
the strip P/N 3P5315A10531 and/or
P/N 3P5315A12931 and if replacement is
needed. Otherwise, go to step 3.3.5.
3.3.4 With reference to Figure 7, assemble strips P/N 3P5315A10531 and/or
3P5315A12931 with reference to the following procedure:
3.3.4.1 With reference to Figure 8, manufacture strips
P/N 3P5315A10551 and/or 3P5315A12951 using Aluminium
Sheet AL-ALY 2024.
3.3.4.2 In accordance to CSRP DM CSRP-A-51-21-06-00A-644A-D apply
Chromate Conversion Treatment.
3.3.4.3 With reference to Figure 8 and in accordance with CSRP DM
CSRP-A-51-21-02-02A-257A-D apply a layer of primer on strips
P/N 3P5315A10551 and/or 3P5315A12951.
3.3.4.4 With reference to Figure 7 install n°2 nut plates P/N MS21075L3N
by means of n°4 rivet P/N NAS1097AD3-3 or
P/N MS20426AD3-3 (as applicable) on strips P/N 3P5315A10551
and/or 3P5315A12951.
3.3.4.5 With Reference to Figure 7, install n° 3 new supports
AW001CL504B-N6 by means of n° 3 rivets NAS1720H5L2A on
strips P/N 3P5315A10551 and/or 3P5315A12951. Make sure they
are oriented opposite with respect to nut plates MS21075L3N.
3.3.4.6 With reference to Figure 7, countermark the obtained components
as P/N 3P5315A10531 and/or 3P5315A12931.
NOTE
Perform Step 3.3.5 ONLY in case Steps 3.3.4
was not performed.
3.3.5 With Reference to Figure 7, install n° 3 supports P/N AW001CL504B-N6
by means of n° 3 rivets NAS1720H5L2A on bracket P/N 3P5315A10531
and/or 3P5315A12931. Make sure they are oriented opposite with
respect to nut plates MS21075L3N.
3.3.6 With reference to Figure 9, fix C/As on strips P/N 3P5315A10531 and/or
3P5315A12931 by means of tie wraps.
NOTE
In case of any doubt and/or need to support,
contact Product Support Engineering
([email protected]) in order to
receive further instruction.
2.1.4 If necessary, in accordance with Figure 10 and Figure 11, re-route the
cable harnesses (using if needed also lacing cord to fix the cables with
each other) in order to respect the clearance of at least 10.0 mm from
the diode or any other surrounding structure or component.
2.2 With reference to Figure 10 and 11, perform a visual inspection of the Diode A77.
Make sure that no damage is present on the component.
2.3 In case of any finding, contact Product Support Engineering
([email protected]) in order to receive further instruction.
3. In case of findings, contact Product Support Engineering
([email protected]) to report about the results of the inspections
requested.
STA
3.120
REF
UP
LH
A77 DIODE (REF)
FWD
C
B
3P5315A10531 STRIP ASSY
(REF)
D
3P5315A12931 STRIP ASSY
(REF)
OVERHEAD PANEL (REF)
VIEW A
STRUCTURES AND SYSTEMS ARE PARTIALLY
OMITTED FOR BETTER CLARITY PURPOSE
Figure 1
S.B. N°139-731 EMERGENCY ALERT
DATE: October 11, 2022
REVISION: / Page 13 of 23
STRUCTURES AND SYSTEMS ARE PARTIALLY
OMITTED FOR BETTER CLARITY PURPOSE
VIEW C
SB139-731-002-01
Figure 2 /
S.B. N°139-731 EMERGENCY ALERT
DATE: October 11, 2022
Page 14 of 23 REVISION: /
Figure 3
S.B. N°139-731 EMERGENCY ALERT
DATE: October 11, 2022
REVISION: / Page 15 of 23
Figure 4 /
S.B. N°139-731 EMERGENCY ALERT
DATE: October 11, 2022
Page 16 of 23 REVISION: /
FWD
REVISION: /
3P5315A10531 STIRP ASSY
3P5315A12931 STRIP ASSY (REF)
(REF) A3T6 TERMINAL LUG
A4T8 TERMINAL LUG B1A3 CABLE B1A10
CABLE B1B3 B1B3 B1A4
B1B7 B1A17 B1A8
B1B8 B1A19 A3T4 TERMINAL LUG
A4T4 TERMINAL LUG B1B11 CABLE B1A8
CABLE B1B7 B1A10
BL 0,0
STA 3120
BL 800
BL-550
BL-800
BL 550
A3T12 TERMINAL LUG
A4T12 TERMINAL LUG CABLE B1A4
CABLE B1B11
A4T7 TERMINAL LUG
CABLE B1B22
A77 DIODE (REF)
VIEW D
STRUCTURES AND SYSTEMS ARE PARTIALLY
OMITTED FOR BETTER CLARITY PURPOSE
SB139-731-003-01
Page 17 of 23
Figure 6 /
S.B. N°139-731 EMERGENCY ALERT
DATE: October 11, 2022
Page 18 of 23 REVISION: /
3P5315A10531 STRIP ASSY
3P5315A10551 STRIP
MS21075L3 NUT
MS20426AD3-3 RIVET
(TYP 2 PLACES)
Ø5.00
(TYP 2 PLACES)
3P5315A12951 STRIP
SB139-731-004-01
Figure 7
S.B. N°139-731 EMERGENCY ALERT
DATE: October 11, 2022
REVISION: / Page 19 of 23
3P5315A10551 STRIP
MATERIAL AL-ALY 2024 T3
AMS-QQ-A-250/5, TH 0.81
165.0
45˚
TYP
12.0
38.7
TYP
6.0
TYP
13.3
TY .0
56.5
5
R
12.8
104.7 TYP
N˚2 EQUAL SPACE
3P5315A12951 STRIP
MATERIAL AL-ALY 2024 T3
AMS-QQ-A-250/5, TH 0.81
113.00
92.00
68.50
45.00
24.00
45˚
P.
TY
R
9 .00
TY 5.0
6.00
11.00
19.00
19.00
12.00
P. 0
112.70 12.00
137.00
SB139-731-005-01
Figure 8 /
S.B. N°139-731 EMERGENCY ALERT
DATE: October 11, 2022
Page 20 of 23 REVISION: /
Figure 9
S.B. N°139-731 EMERGENCY ALERT
DATE: October 11, 2022
REVISION: / Page 21 of 23
Figure 10 /
S.B. N°139-731 EMERGENCY ALERT
DATE: October 11, 2022
Page 22 of 23 REVISION: /
Figure 11
S.B. N°139-731 EMERGENCY ALERT
DATE: October 11, 2022
REVISION: / Page 23 of 23
Please send to the following address:
SERVICE BULLETIN COMPLIANCE FORM Date:
LEONARDO S.p.A.
CUSTOMER SUPPORT & SERVICES - ITALY Number:
Fax:
Remarks:
Information:
We request your cooperation in filling this form, in order to keep out statistical data relevant to aircraft configuration up-to-date. The form should be filled in all
its parts and sent to the above address or you can communicate the application also via Technical Bulletin Application Communication Section placed in
Leonardo AW Customer Portal - MyCommunications Area. We thank you beforehand for the information given.