Green Prime

Technical Data Sheet
VValidationDate). 15141 15141 5 1

CN Other
Jotun Interior Primer (C)
Product description
Type
It is a modified acrylic water based alkali resistance sealer paint.
Features and benefits

. It is 100% free from Alkylphenol Ethoxylates (APEO).
. It has low VOC emitting very low odour.
Recommended use
Specially formulated as a sealer or primer that can be used for interior environment.
Substrate
On concrete, cement plaster, masonry.
Product data
Packaging size 5L and 15 L
Colours White
Solids 37 ±2 volume%
Application data
Remarks
Stir well before use.
Application methods
By brush, roller, airless spray or conventional spray.
Guiding data for airless spray

Nozzle tip 0.021" - 0.027"
Spray angle degrees 65° - 85°
Pressure at nozzle 140 - 190 kg/cm² (2100 psi)
Conditions during application

The temperature of the substrate should be minimum 10 °C and at least 3 °C above the dew point of the air,
measured in the vicinity of the substrate. Good ventilation is usually required in confined areas to ensure proper
drying.
Date of issue: 02.09.2014. by Jotun Group Page: 1/3
This Technical Data Sheet supersedes those previously issued.

The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) for this product.
For your nearest local Jotun office, please visit our website at www.jotun.com.
Recommended film thickness per coat

Dry Minimum 30 µm
Dry Maximum 40 µm
Wet Minimum 86 µm
Wet Maximum 114 µm
Film thickness will vary and is calculated as average.
Spreading rate per coat

Theoretical Spreading rate per coat (m²/l) : 9 - 12
Spreading rate depends on film thickness applied, type of texture, surface porosity, imperfections, temperature,
wastage during painting etc.
Thinner
Water
Dilution
The paint is ready to use after proper stirring. If thinning is required, water may be added up to a maximum of
15%
Drying times
Drying times are generally related to air circulation, temperature, film thickness and number of coats, and will
be affected correspondingly. The figures given in the table are typical with:
Good ventilation (Outdoor exposure or free circulation of air)
Typical film thickness
One coat on top of inert substrate
The given data must be considered as guidelines only. The actual drying time and time before recoating may be
shorter or longer, depending on the ambient temperature, film thickness, ventilation, humidity, underlying paint
system, requirement for early handling and mechanical strength etc.
1. Recommended data given is, for recoating with the same generic type of paint.
2. In case of multi-coat application, drying times will be influenced by the number and sequence and by the
total thickness of previous coats applied.
3. The surface should be dry and free from any contamination prior to application of the subsequent coat.
Relative Humidity (RH) 50 % 50 % 50 %
Substrate temperature 10 °C 23 °C 40 °C
Surface (touch) dry 2h 1h 0.5 h
Hard dry 8h 6h 4h
Cured 4h 2h 1h
Directions for use

Surface preparation
The substrate must be sound, clean, dry and free from dust, oil, grease, laitance etc. All traces of foam release
agents must be removed. A light sanding with suitable abrasive material is recommended before application.
Any resulting dust/loose particles must be removed.
Recommended paint system

Primer
Jotun Interior Primer(C): 1 Coat(s)

Topcoat
Strax Matt (C) or Jotaplast (C) : 2 coats
Remarks
Other systems may be specified, depending on area of use.
Storage
The product must be stored in accordance with national regulations. Keep the containers in a dry, cool, well
ventilated space and away from sources of heat and ignition. Containers must be kept tightly closed. Handle
with care.
Health and safety

Please observe the environmental and precautionary notices displayed on the container.
A Material Safety Data Sheet for the product has been issued.
Detailed information regarding health- and safety risks and precautions for the use of this product is specified in
the product's Safety Data Sheet.
First-aid measures, refer to section 4.
Handling and storage, refer to section 7.
Transport information, refer to section 14.
Regulatory information, refer to section 15.
Disclaimer
The information in this document is given to the best of Jotun's knowledge, based on laboratory testing and
practical experience. Jotun's products are considered as semi-finished goods and as such, products are often
used under conditions beyond Jotun's control. Jotun cannot guarantee anything but the quality of the product
itself. Minor product variations may be implemented in order to comply with local requirements. Jotun reserves
the right to change the given data without further notice.
Users should always consult Jotun for specific guidance on the general suitability of this product for their needs
and specific application practices.
If there is any inconsistency between different language issues of this document, the English (United Kingdom)
version will prevail.


Green Prime

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Green Prime

Uploaded by

Copyright:

Available Formats

Technical Data Sheet

VValidationDate). 15141 15141 5 1

Jotun Interior Primer (C)

Features and benefits

Guiding data for airless spray

Conditions during application

Date of issue: 02.09.2014. by Jotun Group Page: 1/3

This Technical Data Sheet supersedes those previously issued.

Recommended film thickness per coat

Spreading rate per coat

Directions for use

Recommended paint system

Date of issue: 02.09.2014. by Jotun Group Page: 2/3

This Technical Data Sheet supersedes those previously issued.

Health and safety

Date of issue: 02.09.2014. by Jotun Group Page: 3/3

This Technical Data Sheet supersedes those previously issued.

You might also like