HTTPSWWW - Rshydro.co - UkPDFsSiemensMAG5000 Manual PDF
HTTPSWWW - Rshydro.co - UkPDFsSiemensMAG5000 Manual PDF
SITRANS F
Introduction 1
Safety notes 2
Description 3
SITRANS F
Installing/Mounting 4
Flowmeters
SITRANS F M MAG 5000/6000 Connecting 5
Commissioning 6
Operating Instructions
Service and maintenance 7
Functions 8
Alarm, error, and system
messages 9
Troubleshooting/FAQs 10
Technical data 11
Spare parts/Accessories 12
Menu diagrams A
Appendix B
01/2010
SFIDK.PS.026.G1.02
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
with a safety alert symbol, indicates that minor personal injury can result if proper precautions are not taken.
CAUTION
without a safety alert symbol, indicates that property damage can result if proper precautions are not taken.
NOTICE
indicates that an unintended result or situation can occur if the corresponding information is not taken into
account.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by personnel qualified for the specific
task in accordance with the relevant documentation for the specific task, in particular its warning notices and
safety instructions. Qualified personnel are those who, based on their training and experience, are capable of
identifying risks and avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended
or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be adhered to. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of the Siemens AG. The remaining trademarks in this
publication may be trademarks whose use by third parties for their own purposes could violate the rights of the
owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.
1 Introduction................................................................................................................................................ 7
1.1 Preface...........................................................................................................................................7
1.2 Items supplied ................................................................................................................................7
1.3 History ............................................................................................................................................8
1.4 Further Information ........................................................................................................................9
2 Safety notes............................................................................................................................................. 11
2.1 Laws and directives .....................................................................................................................11
2.2 Installation in hazardous location.................................................................................................12
3 Description............................................................................................................................................... 13
3.1 System components ....................................................................................................................13
3.2 Operating principle.......................................................................................................................13
3.3 Applications..................................................................................................................................13
3.4 Features .......................................................................................................................................14
3.5 MAG 5000/MAG 6000 versions ...................................................................................................15
4 Installing/Mounting................................................................................................................................... 17
4.1 Installation conditions...................................................................................................................18
4.2 MAG 5000/6000 compact ............................................................................................................20
4.3 Remote installation ......................................................................................................................22
4.4 MAG 5000/6000 CT .....................................................................................................................27
4.4.1 Installing hardware key ................................................................................................................27
4.4.2 Seal device...................................................................................................................................28
4.5 Turning transmitter/keypad ..........................................................................................................29
5 Connecting .............................................................................................................................................. 33
5.1 Electrical connection ....................................................................................................................34
5.2 Connection of add-on modules ....................................................................................................35
6 Commissioning ........................................................................................................................................ 37
6.1 MAG 5000/6000 Blind..................................................................................................................37
6.2 Local user interface......................................................................................................................38
6.3 Menu structure .............................................................................................................................39
6.4 Changing password .....................................................................................................................40
6.5 Changing basic settings...............................................................................................................40
6.6 Changing operator menu setup ...................................................................................................42
6.7 Changing language......................................................................................................................43
Note
It is the responsibility of the customer that the instructions and directions provided in the
manual are read, understood and followed by the relevant personnel before installing the
device.
Inspection
1. Check for mechanical damage due to possible improper handling during shipment. All
claims for damage are to be made promptly to the shipper.
2. Make sure the scope of delivery, and the information on the type plate corresponds to the
ordering information
Device identification
83G1121.10
SITRANS F M MAGFLO
1 MAG 6000
2
Code no.: 7ME6920-1AA10-1AA0
Supply: 115/230V AC 50-60Hz 17VA
IP: 67 / NEMA 6
3
Tamb.: -20° to +60° C 4
① Code number
② Power supply
③ Enclosure rating
④ Ambient temperature
⑤ Approvals
Figure 1-1 MAG 5000/6000 type plate
1.3 History
This document describes:
● SITRANS F MAG 5000 and MAG 6000 transmitters (standard version).
● Optional versions:
– MAG 5000 Blind and MAG 6000 Blind
– MAG 5000 CT and MAG 6000 CT
– MAG 6000 SV
Documentation history
The contents of these instructions are regularly reviewed and corrections are included in
subsequent editions. We welcome all suggestions for improvement.
The following table shows the most important changes in the documentation compared to
each previous edition.
Edition Remarks
01 First edition
01/2010
Note
Alterations to the product, including opening or improper repairs of the product, are not
permitted.
If this requirement is not observed, the CE mark and the manufacturer's warranty will expire.
General requirements
Installation of the equipment must comply with national regulations. For example EN 60079-
14 for the European Community.
CE marked equipment
The CE-mark symbolizes the compliance of the device with the following guidelines:
● EMC-guideline 89/336/EEC
● Low voltage guideline 73/23/EWG
● ATEX Directive 94/9/EG
● CT: (MI-001) Directive 2004/22/EC
WARNING
Equipment used in hazardous areas must be Ex-approved and marked accordingly. It is
required that the special conditions for safe use provided in the manual and in the Ex
certificate are followed!
Ex approvals
CSA Class I, Division 2, Groups A, B, C and D. Code T5 for an ambient temperature of
+60ºC.
FM Class I, Division 2, Groups A, B, C and D and Class I, Zone 2, Group IIC indoor/outdoor
Type IP67 hazardous (classified) locations
EX requirements
It is required that:
● Electrical connections are in accordance with Elex V (VO in explosion hazardous areas)
and EN60079-14 (Installing Electrical Systems in Explosion Hazardous Areas).
● The protective cover over the power supply is properly installed. For intrinsically safe
circuits the connection area can be opened.
● Appropriate cable connectors are used for the output cicuits: intrinsically safe: blue, non-
intrinsically safe: black
● Sensor and transmitter are connected to the potential equalization. For intrinsically safe
output circuits potential equalization must be maintained along the entire connection path.
● Sensor insulation thickness is max. 100mm (only insulated sensors).
● EN50281-1-2 is considered for installation in areas with combustible dust.
● When protective earth (PE) is connected, no potential difference between the protective
earth (PE) and the potential equalization (PA) can exist, even during a fault condition.
Communication solutions
The SITRANS F USM II range of add on modules, presently including HART, Foundation
Fieldbus. MODBUS RTU RS 485, PROFIBUS PA / DP and Devicenet, are all applicable with
the SITRANS F M MAG 6000 transmitter.
3.3 Applications
The DC-powered magnetic flowmeters are suitable for measuring the flow of almost all
electrically conductive liquids, pastes, and slurries with max. 40% solids. The main
applications can be found in the following sectors:
● Water and waste water
● Chemical and pharmaceutical industries
● Food & beverage industry
● Mining, aggregates and cements industries
● Pulp and paper industry
● Steel industry
● Power generation; utility and chilled water industry
3.4 Features
Power supply
2 different types of power supply are available. A 12 ... 24 V AC/DC and a 115 ... 230 V AC
switch mode type.
Coil current module generates a pulsating magnetizing current that drives the coils in the
sensor. The current is permanently monitored and corrected. Errors or cable faults are
registered by the self-monitoring circuit.
Input circuit amplifies the flow-proportional signal from the electrodes. The input impedance
is extremely high: >1014 Ω which allows flow measurements on fluids with conductivities as
low as 5 µS/cm. Measuring errors due to cable capacitance are eliminated due to active
cable screening.
Digital signal processor converts the analog flow signal to a digital signal and suppresses
electrode noise through a digital filter. Inaccuracies in the transmitter as a result of long-term
drift and temperature drift are monitored and continuously compensated for via the self-
monitoring circuit. The analog to digital conversion takes place in an ultra low noise ASIC
with 23 bit signal resolution. This has eliminated the need for range switching. The dynamic
range of the transmitter is therefore unsurpassed with a turn down ratio of minimum 3000:1.
CAN communication
The transmitter operates internally via an internal CAN communication bus. Signals are
transferred through a signal conditioner to the display module and to/from internal/external
option modules and the dialog module.
Dialog module
The display unit consists of a 3-line display and a 6-key keypad. The display shows a flow
rate or a totalizer value as a primary reading.
Output module
The output module converts flow data to analog, digital and relay outputs. The outputs are
galvanically isolated and can be individually set to suit a particular application.
Standard version
The standard version is an IP67 version for compact or remote installation. Its robust design
ensures a long lifetime if installed outdoors.
Blind version
This version carries all the normal MAG 5000/6000 features, except those associated with
the display and keypad.
Both current and digital outputs are available.
Factory setting of current output in unit is switched off when delivered.
CT version
The MAG 5000/6000 CT version is a custody transfer-approved transmitter.
It is approved according to:
● Cold water pattern approval (MAG 5000/6000 CT):
– PTB
– OIML R 49
● Cold water pattern approval (MAG 6000 CT only):
– MI-001
● Hot water pattern approval (MAG 6000 CT only):
– PTB
● Heat meter pattern approval (MAG 6000 CT only):
– OIML R 75
● Other media than water (MAG 6000 CT only):
– OIML R 117
CAUTION
See Cable requirements (Page 68) before installing transmitter
Vibrations
Compact installation
Medium temperature must be in accordance with the graphs showing max. ambient
temperature as a function of medium temperature.
Remote installation
Cable length and type (as described in Cable requirements) must be used.
For installation conditions for sensors, see respective sensor operating instructions.
Note
System will not register flow if black plugs are not connected to connection board
A
7. Fit supply and output cables through cable glands and connect to connection plate as
shown in Electrical connection (Page 34).
Note
Check that your connection board lines up with SENSORPROM® unit, if not, move
SENSORPROM® unit to the other side of terminal box.
CAUTION
Exposing transmitter to direct sunlight may increase operating temperature above its
specified limit, and decrease display visibility.
A sunshield is available as accessory.
At sensor
1. Remove terminal box lid.
2. Remove SENSORPROM® unit from sensor terminal box and mount it in terminal box of
wall mounting unit.
4. Fit and connect electrode (1) and coil (2) cables as shown in Electrical connection
(Page 34).
Note
Unscreened cable ends must be kept as short as possible.
Electrode cable and coil cable must be kept separate to prevent interference.
WARNING
Mount terminal box lid before power up.
Wall mounting
1. Mount bracket on a wall or on a horizontal or a vertical pipe using ordinary hose clips or
duct straps.
2. Ensure that correct SENSORPROM® memory unit is mounted in wall/pipe mounting unit.
3. Fit M20 or ½" NPT cable glands for cables from bottom or sides of terminal box.
3 1
2 4
3 1
2 4
1 Electrode cable
2 Coil cable
3 Power supply
4 Output cable
1. Fit coil, electrode, supply and output cables through cable glands and connect to
connection plate as shown in Electrical connection (Page 34).
2. Fix connection plate with the two diagonally opposite screws.
3. Tighten cable glands to obtain optimum sealing.
CAUTION
When remote mounted, power supply PE wire must be connected to PE terminal ( ).
Coil cable shield must be connected to SHIELD terminal.
CAUTION
Exposing the transmitter to direct sunlight may increase the operating temperature
above its specified limit, and decrease display visibility.
A sun shield is available as accessory.
Note
Hardware key function
Setting of primary operating parameters is blocked during normal operation.
When key is mounted, access to all menu items is gained. When key is removed, primary
settings are blocked in accordance with requirements in authorisation.
Seal transmitter
CAUTION
Seal transmitter to prevent unauthorized access.
2. Drill through marked drilling holes in terminal box and transmitter/lid. Seal transmitter
externally as shown below.
Transmitter
Figure 4-9 Transmitter can be mounted with its front in either direction indicated by the arrows
without turning terminal box
Figure 4-10 Terminal box can be rotated ±90° in order to optimize viewing angle of transmitter
display/keypad
Keypad
1. Remove outer frame using a screwdriver.
4. Tighten the four screws until a mechanical stop is felt in order to obtain IP67 enclosure.
WARNING
Protective conductor terminal
The required cable is min. AGW16 or 1.5 Cu.
WARNING
Wire insulation
The insulation between the connected mains supply and 24 V AC/DC supply for the
flowmeter must at least be rated with double or reinforced insulation at mains voltage.
For field wiring installation: Ensure that the National Installation Code of the country in
which the flowmeters are installed is met.
Note
National installation code
Observe country specific installation directives for field wiring.
Note
Terminals 81 and 84 are only to be connected if special electrode cable with double
screening is used, e.g. when empty pipe function or long cables are used.
Mains supply
Mains supply 115 ... 230 V AC from building installation Class II.
WARNING
Grounding
Connect mains protective earth wire to PE terminal in accordance with diagram (due to
class 1 power supply).
Mechanical counter
Connect a 1000 µF capacitor (capacitor+ to terminal 56 and capacitor- to terminal 58) if a
mechanical counter is connected to terminals 57 and 58 (active output).
Output cables
Use screened cables if long cables are used in noisy environments.
Digital output
If internal resistance of a load exceeds 10 kΩ, connect an external 10 kΩ load resistor in
parallel to this load.
WARNING
Intrinsically safe terminals
Always ensure that distance between cables/wires is minimum 50 mm in order to avoid that
wires/terminals of intrinsically safe circuits get into contact with wires of other cables.
Fasten cables/wires in a way that they cannot get into contact with each other, not even in
case of an error. Keep wire ends as short as possible.
Note
Does not have a display. All factory settings will be uploaded from the SENSORPROM® unit
after power-up.
Changing settings
If other settings are required, a standard transmitter with display and similar power supply
can be used.
1. Unscrew and remove MAG 5000/6000 Blind.
2. Mount standard MAG 5000/6000 transmitter.
3. Change required settings via display and keypad.
All changed data will be stored in SENSORPROM® memory unit.
4. Remove standard transmitter and remount Blind transmitter.
5. Fasten screws holding transmitter.
New settings stored in SENSORPROM® memory unit will be uploaded in blind transmitter.
S Sign field
P Primary field for numeric value flow rate, Totalizer 1 or Totalizer 2)
U Unit field
T Title line with individual information according to operator or setup menu selected.
ST Subtitle line which will either add information to the title line or keep individual information
independent of the title line.
F Alarm field. Two flashing triangles will appear in case of a fault condition.
M Mode field
L Lock field
Figure 6-1 Local User Interface
Keypad
The keypad is used to set the flowmeter. The keys function as follows:
TOP UP KEY This key (when held for 2 sec.) is used to switch between
operator menu and setup menu. In transmitter setup menu,
a short press will cause a return to previous level.
FORWARD KEY This key is used to step forward through the menus. It is the
only key normally used by the operator.
BACKWARD KEY This key is used to step backwards through the menus.
CHANGE KEY With this key settings or numerical values are changed.
Operator menu
The operator menu is for daily operation. It is customized in the operator menu setup. The
transmitter always starts up in operator menu No. 1. The forward and the backward keys
are used to step through the operator menus.
Setup menu
The setup menu is for commissioning and service only. Access to the setup menu is gained
by pressing the top up key for 2 seconds. The setup menu operates in two modes:
● View mode
● Setup mode
View mode is a read-only mode. The pre-selected settings can only be scanned.
Setup mode is a read and write mode. The pre-selected settings can be scanned and
changed. Access to the setup mode is password-protected. The factory set password is
1000.
Access to a submenu in the setup menu is gained by pressing the lock key . Press the top
up key briefly to return to the previous menu. Press longer (2 sec.) to exit the setup menu
and return to operator menu No. 1.
Parameter Description
Main frequency Selection of main power supply frequency corresponding to the country in
which the flowmeter is installed (e.g. 60 Hz in America).
Flow direction Selection of correct flow direction in pipe.
Qmax Setting of measuring range, analog outputs and frequency output. Also
individual dimension-dependent setting of value, decimal point, unit and time.
Qmax 2 Setting of measuring range, analog outputs and frequency output. Also
individual dimension-dependent setting of value, decimal point, unit and time.
This menu is only visible if chosen as external digital input.
Totalizer Setting of unit and decimal point.
Low flow cut-off Setting of a percentage of selected Qmax. This filters noise in installation
reducing fluctuations in display and all outputs.
Parameter Description
Empty pipe cut-off When set to "On" the alarm will indicate when sensor is running empty. All
readings, display and outputs, will indicate zero.
Error level Selecting error level at which flowmeter will detect an error.
Note
Totalizer 2 is not visible when batch is selected as digital output.
Note
Qmax 2 is visible only when chosen as external input.
Changing units
1. Use select key to position cursor below unit.
2. Press change key until requested unit is displayed.
Note
If "Text" is selected in line 2, this line functions as a heading for the value shown in line 3.
Otherwise it shows the actual value of the reading selected.
Check transmitter
If no replacement transmitter is available, check transmitter according to the following check
table.
Power on transmitter
0 Display light on? Yes ⇒ 1
No ⇒ 2
1 Flashing error triangles? Yes ⇒ Check error table
No ⇒ 1.2
1.2 Output and display readings OK? Yes ⇒ 1.2.1
No ⇒ 1.2.2
1.2.1 Transmitter OK Check application
Check installation/sensor/earthing
connection etc.
Power on transmitter
1.2.2 Check cables/conndections OK ⇒ 1.2.1
Check connection board Not OK ⇒ correct fault
Check pins in transmitter multiplug
2 Check cables/conndections OK ⇒ 2.1
Check connection board Not OK ⇒ Correct fault
Check pins in transmitter multiplug
2.1 Output readings OK? Yes ⇒ 2.1.1
No ⇒ 2.1.2.
2.1.1 Dispaly defective Replace display
2.1.2 Transmitter defective Replace transmitter
Note
Sensor check list
Check list for sensors are included in the respective sensor operating instructions.
CAUTION
Repair and service must be carried out by approved Siemens Flow Instruments personnel
only.
Note
Siemens Flow Instrument defines sensors as non-repairable products.
Technical Support
If you have any technical questions about the device described in these Operating
Instructions and do not find the right answers, you can contact Technical Support:
● Via the Internet using the Support Request:
Support request (http://www.siemens.com/automation/support-request)
● Phone: +49 (0) 180 5050 222
Further information about our technical support is available in the Internet at
Technical support (http://support.automation.siemens.com/WW/view/en/16604318)
Additional Support
Please contact your local Siemens representative and offices if you have additional
questions about the device
Find your contact partner at:
Local contact person (http://www.automation.siemens.com/partner)
Required forms
● Delivery Note
● Cover Note for Return Delivery with the following information
Cover note
(http://cache.automation.siemens.com/dnl/zY/zY0OTg1AAAA_16604370_TxtObj/Begleits
chein_RW_AD.pdf)
– product (ordering number)
– number of devices or spare parts returned
– reason for the return
● Declaration of Decontamination
Decontamination declaration
(http://pia.khe.siemens.com/efiles/feldg/files/Service/declaration_of_decontamination_en.
pdf)
With this declaration you certify that the returned products/spare parts have been
carefully cleaned and are free from any residues.
If the device has been operated together with toxic, caustic, flammable or water-
damaging products, clean the device before return by rinsing or neutralizing. Ensure that
all cavities are free from dangerous substances. Then, double-check the device to ensure
the cleaning is completed.
We will not service a device or spare part unless the declaration of decontamination
confirms proper decontamination of the device or spare part. Shipments without a
declaration of decontamination will be cleaned professionally at your expense before
further proceeding.
You can find the forms on the Internet and on the CD delivered with the device.
7.4 Recalibration
Siemens Flow Instruments offers to recalibrate the sensor. The following calibrations are
offered as standard:
● Standard matched pair calibration
● Customer specified matched pair calibration (up to 10 points)
● Accredited matched pair calibration
Note
For recalibration the memory unit must always be returned with the sensor
Current output
In the current output menu it is possible to select current output range and time constant, see
also Current output menu diagram (Page 79).
If current output is set to "4-20 mA+Alarm", the current output will show the following mA:
● 1.3 mA (if error level is "Fatal").
● 2 mA (if error level is "Permanent").
● 3 mA (if error level is "Warning").
For setting of error level, see error level menu diagram (Page 80).
If current output is not used, it must be set to "Off".
Digital output
Digital output can be used to configure various settings:
● Pulse (volume/pulse, pulse output, pulse width, pulse polarity, and time constant), see
pulse menu diagram (Page 79).
● Frequency (frequency output, max frequency, and time constant), see frequency menu
diagram (Page 80).
● Error settings (level and number), see error level menu diagram (Page 80) and error
number menu diagram (Page 80).
● Limit settings (number of setpoints, setpoint settings, and hysteresis), see direction/limit
menu diagram (Page 81).
● Batch settings (quantity, time and counter settings, and time constant), see batch menu
diagram (Page 82).
Note
Batch settings
Only MAG 6000.
Not available in MAG 5000, MAG 5000 CT and MAG 6000 CT.
Note
When relay is set to batch function, pulse/frequency is not available on digital output.
Relay outputs
Relay output can be used to configure various settings:
● Error settings (level and number), see error level menu diagram (Page 80) and error
number menu diagram (Page 80).
● Limit settings (number of setpoints, setpoint settings, and hysteresis), see direction/limit
menu diagram (Page 81).
● Batch settings (quantity, time and counter settings, and time constant), see batch menu
diagram (Page 82).
● Cleaning (cycle time), see cleaning menu diagram (Page 82).
Note
Batch settings
Only MAG 6000.
Not available in MAG 5000, MAG 5000 CT and MAG 6000 CT.
Note
Cleaning
If a cleaning unit is installed together with transmitter, relay output must always be used
to operate this unit. It cannot be used for other purposes.
Note
Batch settings
Only MAG 6000.
Not available in MAG 5000, MAG 5000 CT and MAG 6000 CT.
Note
Manual cleaning
If the digital input is used for manual cleaning, the relay output also automatically changes to
"cleaning".
Resetting
1. Press top up key for 2 sec.
2. Enter password.
3. Use forward key or backward key to reach reset mode menu.
4. Press lock/unlock key to enter reset menu.
5. Press forward key to reach totalizer/counter to be reset or default setting menu.
6. Press lock/unlock key to start resetting.
If restoring of factory settings is required:
1. Press lock/unlock key again to confirm destruction of customized settings.
See also reset menu diagram (Page 85).
8. Press forward key and then select key and change key to key in offset value.
9. Press lock/unlock key to start adjustment.
Zero point can be adjusted manually in range -1.000 ... +1.000 m3/s. If value outside this
range is keyed in, zero point adjustment will not be implemented.
See also reset mode menu diagram (MAG 6000 SV) (Page 86).
Internal totallizers
Depending on the type of approval it is possible to reset the internal totalizers. The type of
approval is selected in the reset menu (Page 85) with the hardware key mounted. It is
possible to choose between:
● Hot/cold water
● Other liquids
Resetting of totalizers by electrical input is not possible.
Hot/cold water
● Totalizer 1 is allocated to forward flow (cannot be reset)
● Totalizer 2 is allocated to reverse flow (cannot be reset)
Other liquids
Both totalizer 1 and totalizer 2 are allocated to measure the net flow, i.e. any reverse flow will
make the totalizers count backwards.
● Totalizer 1 cannot be reset.
● Totalizer 2 can be reset if the flow velocity in the meter pipe is <0.25 m/s. When the
totalizer is reset, the pulse output register will also be reset.
Output
● When choosing hot water, changing the output settings is not allowed and the output
setting menus are not shown in display.
● When choosing cold water or other liquids, all output settings can be changed.
Excitation frequency
The MAG 6000 SV excitation frequency can be changed in sensor characteristics menu
(Page 84) to one of the following frequencies:
● 1 9/16 Hz
● 3 1/8 Hz
● 6 ¼ Hz
● 12½ Hz
● 25 Hz
● 44 Hz
Note
Calibration has been made with the frequency stored in SENSORPROM® memory unit. A
change in excitation frequency is not recommended and will always mean decreased
measuring accuracy. In some instances, however, it may be necessary to change
frequency due to pulsating flow from piston pumps or other resonance frequencies from
surroundings.
It is highly recommended to carry out a zero point adjustment after changing the excitation
frequency as the offset is affected by the frequency selected. When this is done, the
decrease in measuring accuracy can be kept below 1% o.r.
A too high frequency for the sensor used will cause a coil current alarm indication.
Error system
Transmitter system is equipped with an error and status log system with 4 groups of
information.
(I) Information - system will continue to measure as normal, relay and current outputs will not
be affected.
(W) Warning - system will continue to measure, but an event that may cause a system
malfunction and require operator attention has occurred. The cause of the error may
disappear on its own.
(P) Permanent error - may cause malfunction in the application and operator attention is
required.
(F) Fatal error - is essential for the operation of the flowmeter. Immediate operator attention
is required.
Two menus are available in service and operator menus for registration of information and
errors.
● Error pending
● Status log
Error pending
The first 9 pending errors are stored in the error pending list. When the error is corrected, it
is removed from the error pending list.
The acceptance level for "error pending" can be individually configured to a particular
application.
The acceptance level is set in the basic settings menu (Page 40).
Acceptance levels
The following three acceptance levels are selectable.
● Fatal error: Only fatal errors are registered as errors
● Permanent error: Permanent and fatal errors are registered as errors
● Warning (Default value): Warnings, permanent and fatal errors are registered as errors
Error information is displayed in title and subtitle lines, see display layout (Page 38). Title line
will show time since occurrence of error in days, hours and minutes. Subtitle line will flash
between an error text and a remedy text. Error text will indicate type of error (I, W, P or F),
error number, and error text. Remedy text will inform operator of action to take to remove
error.
Status log
The latest 9 errors are stored in the status log. Errors are stored in the status log for 180
days, even if they are corrected.
Alarm field
The alarm field on the display will always flash when an error is pending.
Error output
The digital and relay output can be activated individually error by error (error level). The relay
output is default selected to error level. An output can also be selected to activate on a single
error number.
The alarm field, error output and error pending always operate together.
The analog output turns to a 1 mA level when in the 4 ... 20 mA mode.
Operator menu
Error pending and status log are as default enabled ( ) in the operator menu.
Mode of operation and design Measuring principle Electromagnetic with pulsed constant field
Empty pipe Detection of empty pipe (special cable
required in remote mounted installation)
Excitation frequency Depends on sensor size
Electrode input impedance > 1 x 1014 Ω
Input Digital input 11 ... 30 V DC, Ri = 4.4 KΩ
Activation time 50 ms
Current IDC 11 V = 2.5 mA, IDC 30 V = 7 mA
Output Current output
Signal range 0 ... 20 mA or 4 ... 20 mA, Alarm
Load < 800 Ω
Time constant 0.1 … 30 s, adjustable (for batch: fixed at 0.1
s)
Digital output
Frequency 0 ... 10 kHz, 50% duty cycle
(uni/bidirectional)
Pulse (active) DC 24 V, 30 mA, 1 kΩ ≤ Ri ≤10 kΩ, short-
circuit protected (power supplied from
flowmeter)
Pulse (passive) DC 3 … 30 V, max. 110 mA, 200 Ω ≤ Ri ≤10
kΩ (powered from connected equipment)
Time constant 0.1 … 30 s, adjustable (for batch: fixed at 0.1
s)
Relay output
Time constant Changeover relay, same as current output
Load 42 V AC/2 A, 24 V DC/1 A
Low flow cut off 0 ... 9.9% of maximum flow
11.2 Accuracy
For accuracy reference conditions, please see below.
[±% E]
3,0
2,8
V: Flow velocity
2,6 E: Meter uncertainty as a percentage of measured value
2,4 v ≥ 0.1 m/s (0.3 ft/s) --> E: ±0.4 ± 1 mm/s *
v < 0.1 m/s (0.3 ft/s) --> E: ±(0.25/v) % of measured value
2,2
2,0 * MAG 5100 W with DN 350 ... 2000
v ≥ 0.1 m/s (0.3 ft/s) --> E: ±0.4 ± 2 mm/s
1,8
v < 0.1 m/s (0.3 ft/s) --> E: ±(0.25/v) % of measured value
1,6
1,4
1,2
1,0
0,8
0,6
0,4
0,2
0,0
0 1 2 3 4 5 6 7 8 9 10 11 12 [m/s]
Figure 11-1 MAG 5000 with MAG 1100, MAG 1100 F, MAG 5100 W, MAG 3100 and MAG 3100 P
[±% E]
1,4
V: Flow velocity
E: Meter uncertainty as a percentage of measured value
1,2 v ≥ 0.1 m/s (0.3 ft/s) --> E: ±0.2 ± 1 mm/s *
v < 0.1 m/s (0.3 ft/s) --> E: ±(0.125/v) % of measured value *
1,0 * MAG 5100 W (Order No. 7ME652...) with DN 350 ... 1200
v ≥ 0.1 m/s (0.3 ft/s) --> E: ±0.2 ± 2.5 mm/s
v < 0.1 m/s (0.3 ft/s) --> E: ±(0.25/v) % of measured value
0,8
0,6
0,4
0,2
0,0
0 1 2 3 4 5 6 7 8 9 10 11 12 [m/s]
0 3.3 6.6 9.9 13 16 20 23 26 30 33 36 39 [ft/s]
Figure 11-2 MAG 6000 with MAG 1100 (not PFA), MAG 1100 F (not PFA), MAG 5100 W, MAG 3100 and MAG 3100 P
Reference conditions
(ISO 9104 and DIN/EN 29104)
A calibration certificate is shipped with every sensor and calibration data are stored in
SENSORPROM memory unit.
4 ... 20 mA
Frequency
Pulse output
83G1082b.10.10.02
Cable kit with standard coil cable and electrode cable double
shielded (also available as low noise cable for MAG 1100
sensor )
Technical data
Coil Electrode
cable cable
Basic data No. of conductors 2 3
Min. sqr. area 0.5 mm2 0.2 mm2
Screen Yes Yes
Max. capacitance N/A 350 pF/m
Max. cable loop resistance Media temperature:
< 100 °C 40 Ω N/A
> 200 °C 6Ω N/A
Cable glands on sensor and M20x1.5 gland - Cable ø 5 ... 13 mm (0.20 ... 0.51 inches)
transmitter ½ NPT gland - cable ø 5 ... 9 mm (0.20 ... 0.35 inches)
12.2 Accessories
Description
Wall mounting unit
Description
Connection plate
Display unit
Description
Sun shield
Note
Sealing
Menus marked with gray are locked when transmitter is sealed.
1) Not at batch
A.12 Direction/limit
A.13 Batch
A.14 Cleaning
Note
Relay outputs
If cleaning unit is installed, relay outputs must always be used to operate cleaning.
Relay outputs cannot be used for other purposes
Note
MAG 6000 SV
The frequency can be set to 44 Hz in the MAG 6000 SV transmitter only.
1) Standard
2) If digital input is set to frequency
3) Not when relay is set to batch
Sensor Sensor
characteristics characteristi
Correction factor 1 0.85 ... 2.00 cs
(Page 84)
Language Language English English, German, French, Danish, Swedish, Language
Finnish, Spanish, Russian, Italian, Portuguese, mode
Polish (Page 79)
Operator menu Primary field Flow rate Flow rate, Totalizer 1, Totalizer 2 Operator
Title/subtitle lines Flow rate Flow rate, Flow rate %, Qmax, Totalizer 1, menu setup
Totalizer 2, Totalizer 1 reset, Totalizer 2 reset, (Page 78)
Batch start/paused/stop, Batch cycle counter,
Batch cycle counter reset, Sensor size, Sensor
type, Error pending, Status log, Tag No.
1): Available on MAG 6000 only.
Nominal size 50 Hz 60 Hz
mm inch BASIC SETTING OUTPUT SETUP BASIC SETTING OUTPUT SETUP
Q-max Volume/pulse Q-max Volume/pulse
B.3 Approvals/certificates
B.3.1 Certificates
All certificates are posted on the Internet. Additionally, the CE Declaration of Conformity as
well as ATEX approvals are available on the Sitrans F literature CD-ROM.
Certificates (http://support.automation.siemens.com/WW/view/en/10806951/134200)
A M
Add-on module, 13 Mains supply, 33
Add-on modules Maintenance, 45
Electrical connection:Add-on modules, 35
P
C Protective conductor terminal, 33
Communication module, (See Add-on module) Protective earth, 33
Compliance, 11
Contact person, 9
Customer Support Hotline, 46 R
Recalibration, 48
Repair, 46
D
Return procedures, 47
Decontamination, 47
Device
Identification, 8 S
Inspection, 7
Safety
Instrument safety standards, 11
Safety notes, 11
E
Service, 46
Electrical connection, 35 Support, 46
System components, 13
H
W
Hotline, 46
Wire insulation, 33
I
Internet
Contact person, 9, 47
Flowdocumentation, 9
Support, 46
Introduction, 7
L
Laws and directives, 11
A5E02338368-01
Siemens Flow Instruments A/S Subject to change without prior notice
Nordborgvej 81 Order No.: A5E02338368-01
DK-6430 Nordborg Copyright Siemens AG 01.2010
All rights reserved
www.siemens.com/processautomation