Abaqus Tube To Tube Modeling
Abaqus Tube To Tube Modeling
no
Modeling Tube-to-Tube
August 19 - 2010
www.lhe.no/download/Abaqus_Tube-to-Tube_modeling.pdf
www.lhe.no
Modeling Tube-to-Tube
August 19 - 2010
In our model, the 2 m inner pipe is defined as the Slide Line, and the 1m outer pipe has got contact elements attached to its nodes. Only the 10 lower nodes of Beam-2m are included in the slide line, meaning that the upper part of Beam-2m is not in contact with Beam-1m. It doesnt matter if the mesh is native (imported into CAE) or modeled in CAE. You can see in the input file that Beam-1m has a native mesh.
www.lhe.no/download/Abaqus_Tube-to-Tube_modeling.pdf
www.lhe.no
Modeling Tube-to-Tube
August 19 - 2010
Use contact Element of Type=ITT21 together with 2-dimensional beam, pipe or truss elements, and Type=ITT31 together with three-dimensional beam, pipe or truss elements. Elset = TTT will not be recognized outside the Instance. Remember to define later, see step 2. Step 2: Defining element set for contact elements (optional) Since the ELSET for the contact elements (ELSET=TTT) is defined inside the Instance, an ELSET will have to be created outside the Instance too, so that the element set can be recognized when connected to the slide line. In our model, we are using the same name (TTT). *Elset, elset=TTT, instance=Beam-1m, generate 11,21, 1 Step 3: Defining Element Properties for contact elements Defining Contact element properties is very simple, since there is only the radial clearance that needs to be defined. *Interface, Elset=TTT 0.001 Here, you are giving Elset=TTT defined above (the contact elements attached to Beam1m) the radial clearance 0.001 m. Normally, the radial clearance is equal to the space between the inner diameter of the outer pipe and the outer diameter of inner pipe, but in this case we have a liner or something in between. See Figure 3 for details on radial clearance.
Step 4: Defining Slide Line Finally, the slide line needs to be defined. The slide line consists of nodes only. In our case, the inner pipe is the slide line. Figure 4 show the Slide Line. NOTE: Since the nodes of the Beam-2m is defined inside the part, we need to include the part name with the node numbers. This would not be necessary if you created the input file without parts and instances. www.lhe.no/download/Abaqus_Tube-to-Tube_modeling.pdf 3
www.lhe.no
Modeling Tube-to-Tube
August 19 - 2010
Choosing which pipe will have the slide line: In the case of internal tube-to-tube contact, the slide line can be placed on the inner tube or the outer tube. Generally the slide line should be associated with the outer tube. However, if the inner tube is stiffer than the outer tube, the slide line should be attached to the inner tube. Note: In our model it was defined the wrong way, i.e. inner/ least stiff tube is slide line. *SLIDE LINE, ELSET=TTT, TYPE=LINEAR Beam-2m.1, Beam-2m.2, Beam-2m.3, Beam-2m.4, Beam-2m.5, Beam-2m.6, Beam-2m.7, Beam-2m.8, Beam-2m.9, Beam-2m.10, Beam-2m.11 In the *Slide Line command, you are connecting the nodes in the slide line with ELSET=TTT. Set TYPE=LINEAR to define a slide line made up of linear elements (B31), and TYPE=PARABOLIC to define a slide line made up of parabolic elements (B32 )
www.lhe.no/download/Abaqus_Tube-to-Tube_modeling.pdf
www.lhe.no
Modeling Tube-to-Tube
August 19 - 2010
Results
Displacement on top of Beam-2m is listed in Table 1. Three radial clearance values have been run: 0.1 mm, 1 mm and 5 mm. Figure 5 show the deformation plot for 1 mm radial clearance.
Table 1. Deformation on top of Beam-2m
0.1 mm 5.42 mm
1 mm 6.41 mm
5 mm 8.42 mm
www.lhe.no/download/Abaqus_Tube-to-Tube_modeling.pdf
www.lhe.no
Modeling Tube-to-Tube
August 19 - 2010
INPUT FILE
The inputfile shown below can be downloaded here (www.lhe.no/download/TTTtest.inp). An inputfile with opposite slide line (outer tube/pipe is slide line) can be downloaded here (www.lhe.no/download/TTT-test1.inp) ******************** INPUT FILE STARTS HERE ******************** *Heading Modeling Tube-to-Tube using Parts and Instances ** ** August 19, 2010 ** Created by Lars Hansen, L Hansen Engineering ** www.lhe.no ** ** PARTS *Part, name=Beam-1m-P *End Part ** *Part, name=Beam-2m-P *Node 1, 0., 0.0, 0. 2, 0., 0.1, 0. 3, 0., 0.2, 0. 4, 0., 0.3, 0. 5, 0., 0.4, 0. 6, 0., 0.5, 0. 7, 0., 0.6, 0. 8, 0., 0.7, 0. 9, 0., 0.8, 0. 10, 0., 0.9, 0. 11, 0., 1.0, 0. 12, 0., 1.1, 0. 13, 0., 1.2, 0. 14, 0., 1.3, 0. 15, 0., 1.4, 0. 16, 0., 1.5, 0. 17, 0., 1.6, 0. 18, 0., 1.7, 0. 19, 0., 1.8, 0. 20, 0., 1.9, 0. 21, 0., 2.0, 0. *Element, type=B31 1, 1, 2 2, 2, 3 www.lhe.no/download/Abaqus_Tube-to-Tube_modeling.pdf 6
www.lhe.no
Modeling Tube-to-Tube
August 19 - 2010
3, 3, 4 4, 4, 5 5, 5, 6 6, 6, 7 7, 7, 8 8, 8, 9 9, 9, 10 10, 10, 11 11, 11, 12 12, 12, 13 13, 13, 14 14, 14, 15 15, 15, 16 16, 16, 17 17, 17, 18 18, 18, 19 19, 19, 20 20, 20, 21 *Nset, nset=_PickedSet2, internal, generate 1, 21, 1 *Elset, elset=_PickedSet2, internal, generate 1, 20, 1 ** Section: Wellhead-20inx0_835in Profile: Casing-20inx0835in *Beam General Section, elset=_PickedSet2, poisson = 0.3, section=GENERAL 0.0324349, 0.0039912, 0.00282221, 0.0039912, 0.00798242 0.,0.,-1. 2.1e+11, 8.07692e+10 *End Part ** ** ** ASSEMBLY ** *Assembly, name=Assembly ** ** *Instance, name=Beam-2m, part=Beam-2m-P *End Instance ** *Instance, name=Beam-1m, part=Beam-1m-P *Node 1, 0., 0.0, 0. 2, 0., 0.1, 0. 3, 0., 0.2, 0. 4, 0., 0.3, 0. 5, 0., 0.4, 0. 6, 0., 0.5, 0. www.lhe.no/download/Abaqus_Tube-to-Tube_modeling.pdf 7
www.lhe.no
Modeling Tube-to-Tube
August 19 - 2010
7, 0., 0.6, 0. 8, 0., 0.7, 0. 9, 0., 0.8, 0. 10, 0., 0.9, 0. 11, 0., 1.0, 0. *Element, type=B31 1, 1, 2 2, 2, 3 3, 3, 4 4, 4, 5 5, 5, 6 6, 6, 7 7, 7, 8 8, 8, 9 9, 9, 10 10, 10, 11 *Element, type=ITT21, ELSET=TTT 11, 1 12, 2 13, 3 14, 4 15, 5 16, 6 17, 7 18, 8 19, 9 20, 10 21, 11 *Nset, nset=_PickedSet3, internal, generate 1, 11, 1 *Elset, elset=_PickedSet3, internal, generate 1, 10, 1 ** Section: Conductor-30inx1in Profile: Casing-30inx1in *Beam General Section, elset=_PickedSet3, poisson = 0.3, section=GENERAL 0.0587781, 0.0039912, 0.00282221, 0.0039912, 0.00798242 0.,0.,-1. 2.1e+11, 8.07692e+10 *INTERFACE, ELSET=TTT 0.001 *End Instance ** *SLIDE LINE, ELSET=TTT, TYPE=LINEAR Beam-2m.1, Beam-2m.2, Beam-2m.3, Beam-2m.4, Beam-2m.5, Beam-2m.6, Beam-2m.7, Beam-2m.8, Beam-2m.9, Beam-2m.10, Beam-2m.11 ** www.lhe.no/download/Abaqus_Tube-to-Tube_modeling.pdf 8
www.lhe.no
Modeling Tube-to-Tube
August 19 - 2010
*Elset, elset=TTT, instance=Beam-1m, generate 11,21, 1 *Nset, nset=Beam-2m-bottom, internal, instance=Beam-2m 1, *Nset, nset=Beam-1m-bottom, internal, instance=Beam-1m 1, *Nset, nset=Beam-2m-top, internal, instance=Beam-2m 21, *End Assembly ** ** MATERIALS ** *Material, name=Steel *Density 7810., *Elastic 2.1e+11, 0.3 ** ---------------------------------------------------------------** ** STEP: Bending ** *Step, name=Bending, nlgeom=YES *Static 0.1, 1., 1e-05, 1. ** ** BOUNDARY CONDITIONS ** *Boundary Beam-1m-bottom, ENCASTRE Beam-2m-bottom, ENCASTRE ** ** LOADS ** *Cload Beam-2m-top, 1, 1000000. ** ** OUTPUT REQUESTS ** *Restart, write, frequency=0 ** ** FIELD OUTPUT: F-Output-1 ** *Output, field, variable=PRESELECT ** *End Step
www.lhe.no/download/Abaqus_Tube-to-Tube_modeling.pdf