PVS-7D - NVG
PVS-7D - NVG
TECHNICAL MANUAL
UNIT AND DIRECT SUPPORT
MAINTENANCE MANUAL INCLUDING
REPAIR PARTS AND SPECIAL TOOLS LIST
NIGHT VISION GOGGLES (NVG)
AN/PVS-7B
(NSN 5855-01-228-0937) (EIC: IPS)
AND
AN/PVS-7D
(NSN 5855-01-422-5413) (EIC: N/A)
DISTRIBUTION STATEMENT C. Distribution authorized to U.S. Government agencies and their contractors.
This publication is required for administration and operational purposes, as determined 8 July 1991. Other
requests for this document shall be referred to either: Commander, U.S. Army Communications-Electronics
Command and Fort Monmouth, ATTN: AMSEL-LC-LEO-E-ED-P, Fort Monmouth, NJ 07703-5000; or
Commander, Warner-Robins Air Logistics Center/LYE, 380 2nd Street, Suite 104, Robins AFB, GA 31098-1638;
or Commandant of the Marine Corps (ARD), Washington, DC 20380-0001; or Commanding Officer, Naval Ship
Weapons Systems Engineering Station (Code L700), Port Hueneme, CA 93043-5007.
DESTRUCTION NOTICE For unclassified, limited documents, destroy by any method that will prevent
disclosure of contents or reconstruction of the document.
TM 11-5855-262-23&P-2
WARNING
Equipment Limitations
To avoid physical and equipment damage when using the Night Vision Goggles (NVG), carefully read
and understand the following safety precautions.
The NVG requires some night light (moonlight, starlight, etc.) to operate.
performance depends upon the level of light.
The level of
Night light is reduced by passing cloud cover, while operating under trees, in building
shadows, etc.
The NVG is less effective viewing into shadows and other darkened areas.
The NVG is less effective through rain, fog, sleet, snow, smoke, and other reflective
material.
The NVG will not see through dense smoke.
Adjust vehicular speed to prevent overdriving the range of view when conditions of possible
reduction or loss of vision exist.
WARNING
Do not carry batteries in pockets containing metal objects such as coins, keys, etc.
Metal objects can cause the batteries to short circuit and become very hot. In the case
of lithium batteries, a short circuit could cause them to explode.
WARNING
Danger of Explosion
The BA-5567/U lithium battery contains sulfur dioxide gas under pressure and should be handled in the
following manner:
Do not heat, puncture, disassemble, short circuit, attempt to recharge, or otherwise tamper
with the batteries.
Turn off the equipment if the battery compartment becomes unduly hot. If possible, wait
until the batteries have cooled before removing them.
The batteries have safety vents to prevent explosion. When they are venting gas, you will
smell it (very irritating) or hear the sound of gas escaping. When the safety vents have
operated, the batteries are fairly safe from bursting, but will be hot and must be handled with
care.
If you inhale sulfur dioxide, seek medical attention.
TM 11-5855-262-23&P-2
WARNING
Toxic Material
The image intensifiers phosphor screen contains toxic materials.
If an image intensifier breaks, be extremely careful to avoid inhaling the phosphor screen
material. Do not allow the material to come in contact with the mouth or open wounds on
the skin.
If the phosphor screen material contacts your skin, wash it off immediately with soap and
water.
If you inhale/swallow any phosphor screen material, drink a lot of water, induce vomiting,
and seek medical attention as soon as possible.
WARNING
Do not use any battery other than a BA-5567/U, AA alkaline, or 1.5 volt AA L91 lithium
battery in the NVG. DO NOT use any battery(ies) providing a (combined) voltage
greater than 3.0 volts.
WARNING
The IR source is a light that is invisible to the unaided eye for use during conditions of
extreme darkness. However, the light from the IR source can be detected by the enemy
using night vision devices. The IR spot/flood lens accessory does not reduce the ability
of an enemy to detect the illuminator.
WARNING
The compass illuminator can be seen by other night vision users.
WARNING
Personnel Injury
Serious injury may result if the nitrogen tank valve breaks off due to
tank upset. If the tank valve breaks, the tank can be propelled by the
escaping gas and strike you or others.
Always secure the tank to an upright support before removing the tank
valve guard and attaching the regulator valve to the tank.
WARNING
It is critical that the goggles be turned off manually before placing them in the flipped up
position in order to avoid detection by the enemy.
b
TM 11-5855-262-23&P-2
WARNING
When installing the headmount over the protective mask, be careful not to break the
protective mask seal around your face.
WARNING
Do not use contaminated eyecups. They must be replaced.
FIRST AID
For first aid or artificial respiration, see FM 21-11, First Aid for Soldiers.
c/d blank
*TM 11-5855-262-23&P-2
TECHNICAL MANUAL
No. TM 11-5855-262-23&P-2
TECHNICAL ORDER
No. 12S10-2PVS7-12
TECHNICAL MANUAL
No. 09500A-23&P/2A
TECHNICAL MANUAL
No. SW215-AT-MAB-010
i/ii blank
TM 11-5855-262-23&P-2
TABLE OF CONTENTS
Paragraph
Title
Page
Section I
1-1
1-2
1-3
1-4
1-5
1-6
1-7
1-8
Section II
1-9
1-10
1-11
1-12
Section III
1-13
1-14
1-15
CHAPTER 2
Section I
2-1
2-2
2-3
Repair Parts, Tools, Special Tools, TMDE, and Support Equipment .............. 2-1
Common Tools and Equipment...................................................................... 2-1
Special Tools, TMDE, and Support Equipment .............................................. 2-2
Repair Parts................................................................................................... 2-2
Section II
2-4
2-5
2-6
Section III
2-7
2-8
Section IV
2-9
2-10
iii
TM 11-5855-262-23&P-2
TABLE OF CONTENTS - Continued
Paragraph
Section V
2-11
2-12
iv
Title
Page
2-13
2-14
2-15
2-16
2-17
2-18
2-19
2-20
Section VI
2-21
CHAPTER 3
Section I
3-1
3-2
3-3
Section II
3-4
3-5
Section III
3-6
Servicing .......................................................................................................3-2
Scope .............................................................................................................3-2
Section IV
3-7
3-8
3-9
3-10
3-11
Troubleshooting ............................................................................................3-3
Troubleshooting..............................................................................................3-3
TS-3895A/UV Preparation for Use..................................................................3-6
Testing the NVG Using TS-3895A/UV ............................................................3-6
Electrical Troubleshooting ............................................................................3-10
Black Spot Check .........................................................................................3-12
Section V
3-12
3-13
TM 11-5855-262-23&P-2
TABLE OF CONTENTS - Continued
Paragraph
Title
Page
3-14
3-15
3-16
3-17
3-18
3-19
Section VI
3-20
3-21
APPENDIX A
A-1
A-2
A-3
A-4
A-5
A-6
A-7
REFERENCES
Scope ...........................................................................................A-1
Forms ...........................................................................................A-1
Field Manuals ...............................................................................A-1
Technical Manuals ........................................................................A-1
Miscellaneous Publications ...........................................................A-1
Marine Corps Use .........................................................................A-2
Air Force Use................................................................................A-2
APPENDIX B
Section I
B-1
B-2
B-3
B-4
Section IV
APPENDIX C
Section I
C-1
C-2
C-3
C-4
C-5
C-6
C-7
Section II
Group 00
Group 01
Group 02
Section III
Group 10
Section IV
B-5
Section II
Section III
Figure
C-1
C-2
C-3
C-4
TM 11-5855-262-23&P-2
TABLE OF CONTENTS - Continued
Paragraph
vi
Title
Page
APPENDIX D
Section I
D-1
D-2
Section II
APPENDIX E
Section I
Section II
Section III
E-1
GLOSSARY
Section I
Section II
ALPHABETICAL
INDEX
...............................................................................................Index-1
Figure
E-1
E-1
TM 11-5855-262-23&P-2
HOW TO USE THIS MANUAL
Usage
You must familiarize yourself with the entire maintenance procedure before beginning the
maintenance task. Read and follow all Warnings, Cautions and Notes.
Manual Overview
The contents of each chapter are listed at the beginning of the chapter. This listing includes the
paragraph title and page number. Additional references to the contents of this manual can be found
in the index at the back of the manual. This manual also contains the Repair Parts and Special Tools
List (RPSTL) in Appendix C for ordering repair parts. Appendix C gives details for using the RPSTL.
Special Feature
A locator is provided on the right-hand border of the front cover. This gives the location of the
information most frequently used. To find the topic UNIT TROUBLESHOOTING, open the manual to
the correct page by using the black tab on the side of the manual that lines up with the topic UNIT
TROUBLESHOOTING.
vii/viii blank
TM 11-5855-262-23&P-2
CHAPTER 1
INTRODUCTION
Page
Overview...................................................................................................................... 1-1
Scope .......................................................................................................................... 1-1
Maintenance Forms, Records, and Reports ................................................................. 1-2
Destruction of Electronic Materiel to Prevent Enemy Use ............................................ 1-2
Preparation for Storage or Shipment............................................................................ 1-2
Official Nomenclature, Names, and Designations ........................................................ 1-2
Reporting Equipment Improvement Recommendations (EIR) ...................................... 1-4
Warranty Information ................................................................................................... 1-4
Corrosion Prevention and Control (CPC) ..................................................................... 1-8
Equipment Characteristics, Capabilities, and Features ................................................ 1-9
Location and Description of Major Components......................................................... 1-10
Configuration of Image Intensifier .............................................................................. 1-15
Equipment Data ......................................................................................................... 1-16
Mechanical Functions ................................................................................................ 1-18
Optical Functions ....................................................................................................... 1-19
Electronic Circuit Function ......................................................................................... 1-19
OVERVIEW
Chapter 1 of this technical manual is intended to give you information regarding the type of equipment,
its characteristics, and the principles of operation that will help you maintain it properly. Figure 1-2
(Sheets 1 through 4), shows the storage locations of components in the carrying cases.
Type of Manual: Unit and Direct Support Maintenance including Repair Parts and Special Tools
List (RPSTL).
b.
Model Number and Equipment Name: Night Vision Goggles (NVG), AN/PVS-7B and AN/PVS-7D.
c.
Purpose of Equipment: The NVG are self-contained night vision devices that enable improved
night vision using ambient light from the night sky (moon, stars, skyglow, etc.).
1-1
TM 11-5855-262-23&P-2
1-2 MAINTENANCE FORMS, RECORDS, AND REPORTS
Department of the Army forms and procedures used for equipment maintenance will be those
prescribed by DA Pam 738-750, as contained in Maintenance Management Update. Refer to the latest
issue of DA Pam 25-30 to determine whether there are new editions, changes or additional publications
or forms pertaining to this equipment.
Marine Corps personnel refer to the on-line Marine Corps Publication Distribution System (MCPDS).
Marine Corps Ground Equipment Record Procedures. Marine Corps personnel refer to TM 4700-15/1
for disposition of forms and records required for Marine Corps equipment.
1-2
TM 11-5855-262-23&P-2
1-5 OFFICIAL NOMENCLATURE, NAMES, AND DESIGNATIONS - Continued
Table 1-1. Nomenclature Cross-Reference List.
__________________________________________________________________________________
COMMON NAME
OFFICIAL NOMENCLATURE
__________________________________________________________________________________
3X Magnifier
Magnifier Lens Assembly
Batteries
Battery, Nonrechargeable
Battery Cap
Battery Cap Assembly
Battery Cap Retainer
Retainer, Electrical
Carrying Case
Case, Infrared Equipment
Carrying Case Strap
Strapping
Chinstrap
Strap, Helmet
Collimator
Collimator, Infrared
Compass
Compass Assembly
Cross Strap
Strapping
Demist Shields
Demist Shield Assy
Eyecup
Eyecup
Goggles
Goggle Assembly
Headmount
Headset Assembly
Helmet Mount
Mount, Viewer
Image Intensifier
Image Intensifier, Night Vision
IR Spot/Flood Lens
Lens Assembly, Focusing
LIF
Filter, Infrared Light
Medium Browpad
Browpad Assy, Medium
Neck Cord
Cord, Fibrous
Neck Pad
Neck Pad Assembly
Objective Lens
Mount Assy, Objective
Objective Lens Cap
Cap, Protective, Dust
O-Ring
Packing, Preformed
Power Switch
Switch, Knob Assembly
Purge Device
Device, Purge
Purge Screw
Screw, Machine
Rear Cover
Rear Cover Assembly
Sacrificial Window
Window, Sacrificial
Screw
Screw, Machine
Shipping and Storage Case
Case, Shipping/Storage
Side Strap
Strap, Webbing
Tethering Cord
Clip, Retaining
Thick Browpad
Browpad Assy, Thick
Thin Browpad
Browpad Assy, Thin
Washer
Washer, Flat
Wired Housing
Wired Housing Assembly
__________________________________________________________________________________
1-3
TM 11-5855-262-23&P-2
1-6 REPORTING EQUIPMENT IMPROVEMENT RECOMMENDATIONS (EIR)
If your NVG needs improvement, let us know. Send us an EIR. You, the user, are the only one who
can tell us what you dont like about the design. Put it on an SF 368 Product Quality Deficiency Report.
Mail it to Commander, U.S. Army Communications-Electronics Command and Fort Monmouth, ATTN:
AMSEL-LC-LEO-D-CS-CFO, Fort Monmouth, New Jersey 07703-5000. We will send you a reply.
MARINE CORPS PERSONNEL are encouraged to submit SF 368 in accordance with MCO 4855.10
(Quality Deficiency Report).
Image tube fails the low light resolution and/or high light resolution.
Image intensifier exhibits any one, or more, of the operational defects described in
Inspection Criteria for Image Intensifier Operation as defined in the Operators
Maintenance Manual (such as, shading, edge glow, flashing, flickering or intermittent
operation).
Obvious mechanical malfunction with no evidence of severe trauma that indicates customer
damage.
The manufacturer will use the same list of criteria in verifying a defect covered by the warranty.
1-4
TM 11-5855-262-23&P-2
1-7 WARRANTY INFORMATION - Continued
Turn-in Procedures.
(1) The operator, after completing the PMCS and Troubleshooting, annotates the fault on DA
Form 2404 (Army) or OPNAV Form 4790/138 (Navy), completes the appropriate blocks and turns the
equipment into the unit maintainer. The unit maintainer will perform all applicable PMCS and
Troubleshooting before determining that the end item does not show any faults or must be sent to
Direct Support (DS)/Intermediate maintenance for further maintenance actions. If it is determined that
the end item needs Intermediate repair, the unit maintainer will annotate DA Form 2407 (Army),
OPNAV Form 4790/60 (Navy/Marine Corps), and include this form with the end item and send it to
appropriate Intermediate maintenance activity. DA Pam 738-750 outlines distribution of copies.
(2) The Direct Support (DS)/Intermediate maintenance activity performs all troubleshooting
and maintenance procedures in accordance with the maintenance manual. If a defect is identified and
the product is under warranty, per the warranty expiration date on the label, a warranty return is
initiated.
1-5
TM 11-5855-262-23&P-2
1-7 WARRANTY INFORMATION - Continued
NOTE
The NVG that fails either the service upon initial receipt of material
inspection or fails prior to the expiration of the warranty must be reported
on a Product Quality Deficiency Report (PQDR), SF 368. This will ensure
the unit submitting the PQDR will receive credit for the NVG. DA Pam
738-750 outlines distribution of copies.
NOTE
If using an automated system such as SAMS or ULLS, use the equivalent
electronic form, to track using the same procedure as for the hard copy
DA Form 2404, 2407 or DD Form 314 etc.
NOTE
For units operating under SAMS, DA Form 5504 (Maintenance Request)
and 5504-1 (Maintenance Request Continuation Sheet) are the only
forms used to file warranty claim actions. Do not use SF 368 to report
Warranty Claims. DA Pam 738-750 outlines distribution of copies.
NAVY ONLY: The item should be tagged (e. g. using the DD Form 1577-2). An OPNAV 4790/60,
VIDS/MAF shall be filled out which will include the nature of the defect, i. e., spots, flicker, edge glow,
etc. and method used to determine type and extent of defect. A product quality deficiency report,
message or form SF 368, should be filed for an IN-WARRANTY item to the FST: Commander, Code
805B-Bldg 3291 NAVSURFWARCENDIV, 300 Highway 361, Crane, IN 47522-5001. No defective
warranty items are to be shipped directly from the field to a contractor. If there are reoccurring
problems for deficient out-of-warranty assemblies, an engineering investigation, in accordance with
OPNAVINST 4790.2G, should be forwarded to the FST.
(3) Activities should follow local procedures for shipping equipment to the manufacturer. DD
Form 1149 (Requisition and Invoice/Shipping Document) will accompany all shipments to the
manufacturer's factory. The manufacturer will prepare a new DD Form 1149 for return shipment to the
relevant activity. DA Pam 738-750 outlines distribution of copies.
b.
Return Procedures. The manufacturer will repair and return all warranted equipment back to
designated activities.
To determine the manufacturer of the item, check the identification plate for the manufacturers (MFR)
CAGEC (Commercial and Government Entity Code).
CAGEC
13567 or 66868
55311 or 51298
Manufacturer
ITT, Roanoke, VA
Litton, Tempe, AZ
RSC, Korea
POC: Mr. Harry Footit
DSN 315-722-3571
[email protected]
TM 11-5855-262-23&P-2
1-7 WARRANTY INFORMATION - Continued
(1)
(a) For items manufactured by ITT (CAGEC 13567 or 66868): This is accomplished by
calling ITT at 1-800-360-6054 during regular business hours 07:30 - 11:30 and 12:30 - 16:30 Eastern
Standard (or Daylight Savings) Time, Monday through Friday. During non-business hours, voice mail
will be operative which will direct the caller to leave name and complete commercial telephone number
including appropriate area code or country/city code and a brief message. ITT will return calls within
two business days. Using voice media, ITT may be able to offer on-the-spot suggestions to help solve
a problem. If the problem cannot be resolved over the phone and the product is under warranty, ITT
will provide the caller with a Return Authorization (RA) number and appropriate shipping instructions.
(b) For items manufactured by Litton (CAGEC 55311 or 51298): This is accomplished
by calling the Litton Customer Service Representative at 1-800-569-8478 during regular business hours
07:00 15:30 Mountain Standard Time, Monday through Friday. The Litton Customer Service
Representative can also be reached at 602-303-8956 during regular business hours. During nonbusiness hours, voice mail is available which will direct the caller to leave a name, complete
commercial telephone number, to include area code or country and city codes, and a brief message.
Litton will return the call within two business days. Using voice media, Litton may be able to offer onthe-spot suggestions to solve a problem. If the problem cannot be addressed over the phone and the
product is under warranty, Litton will provide the caller with a Return Goods Authorization (RGA)
number and appropriate shipping instructions.
(2)
Because of the time zone differences, communication via E-mail may be used by any authorized
customer. This procedure can be utilized 24 hours a day with E-mail access. Prepare an E-mail with
the following information shown below and send it to:
Date:
Branch of Service:
UIC:
Direct Support/Intermediate Activity:
Address
Point of Contact:
Street and Number:
City:
State/Country:
Zip Code:
Commercial Telephone Number (include area code or country/city code):
Commercial FAX Number (include area code or country/city code):
E-mail Address:
Product Information:
Model:
Serial Number:
Reason for Return:
Data Required for E-mail and FAX Communication.
1-7
TM 11-5855-262-23&P-2
1-7 WARRANTY INFORMATION - Continued
(a) For items manufactured by ITT (CAGEC 13567 or 66868): Send the message to ITT
at [email protected] via the internet. ITT will answer via a return message providing
suggestions to help solve the problem or issue a RA number.
(b) For items manufactured by Litton (CAGEC 55311 or 51298): Send the message to
Litton at [email protected] via the Internet. Litton will respond via a return message providing
either a suggestion to solve a specific problem or a RGA number.
(3)
FAX Communication.
(a) For items manufactured by ITT (CAGEC 13567 or 66868): Send a FAX with the
same information as ITT requires for E-mail to ITT at FAX number (540) 366-9015.
(b) For items manufactured by Litton (CAGEC 55311 or 51298): Send a FAX with the
same information, as Litton requires for E-mail to Litton at FAX number 602-966-9055. Litton will
provide a response within two business days.
c.
Repair Procedures. The manufacturer will repair and return all warranted equipment back to
designated activities. An estimated cost of repair will be provided to the maintenance activity for those
items that do not fall within warranty guidelines. The manufacturer will only accept written authorization
from authorized personnel at DS/Intermediate maintenance activity prior to conducting repair.
Things to do to help speed up the return of your equipment:
1.
2.
3.
4.
Review your documents to make sure you have filled in all of the requested
information. Your documentation must clearly explain the problem(s) you are
having with the equipment.
Double check that your return address is legible on all of your documents, as well
as, the shipping package.
Make sure all of the documents, except your copies, are placed inside of the
package before being returned.
Write the RA or RGA number on the outside of your package.
Failure to follow the above guidelines will result in a delay in the return of your
equipment.
1-8
TM 11-5855-262-23&P-2
1-8 CORROSION PREVENTION AND CONTROL (CPC) - Continued
If a corrosion problem is identified, report it using Standard Form 368, Product Quality Deficiency
Report. Use keywords such as "corrosion," "rust," "deterioration," or "cracking" to ensure that the
information is identified as a CPC problem. Submit the form to the address specified in DA Pam 738750.
WARNING
Equipment Limitations
To avoid physical and equipment damage when using the NVG, carefully read and understand the
following safety precautions.
The NVG requires some night light (moonlight, starlight, etc.) to operate.
performance depends upon the level of light.
The level of
Night light is reduced by passing cloud cover, while operating under trees, in building
shadows, etc.
The NVG is less effective viewing into shadows and other darkened areas.
The NVG is less effective through rain, fog, sleet, snow, smoke, and other reflective
material.
The NVG will not see through dense smoke.
Adjust vehicular speed to prevent overdriving the range of view when conditions of possible
reduction or loss of vision exist.
CAUTION
WARNING
The IR source is a light that is invisible to the unaided eye for use during
conditions of extreme darkness. However, the light from the IR source
can be detected by the enemy using night vision devices. The IR
spot/flood lens accessory does not reduce the ability of an enemy to
detect the illuminator.
1-9
TM 11-5855-262-23&P-2
1-9 EQUIPMENT CHARACTERISTICS, CAPABILITIES, AND FEATURES - Continued
NOTE
When utilizing the NVG for driving purposes, the goggles must not be
used in the hand-held mode. The goggles must be worn in the
headmounted or helmet mounted position.
The NVG is a hand-held, headmounted, or helmet mounted night vision system that enables walking,
driving, weapon firing, short-range surveillance, map reading, vehicle maintenance, and administering
first aid in both moonlight and starlight. Each unit allows for vertical adjustment (by using head strap),
fore-and-aft adjustment, objective focus, eyepiece focus, and eye span distance adjustment. The
goggles are also equipped with an IR source and a low-battery indicator. The NVG will not be turned
off automatically when disconnected from the headmount or helmet mount. Turn off the NVG by the
power switch. There is also a high light cut-off feature that cuts off power to the goggles when they are
exposed to high levels of light for 70 30 seconds. Some units may be equipped with a removable
compass and an IR spot/flood lens.
Goggles.
The goggles (Figure 1-2, Sheet 4) consist of four primary subassemblies: an objective lens, a wired
housing, an image intensifier (not shown), and a rear cover. The wired housing contains a built-in
battery compartment, attached battery cap, and the power switch. The goggles also use the
accessories listed below.
(1) Demist Shields - The two demist shields are used to prevent the eyepiece lenses from
becoming fogged.
(2) LIF - The LIF (Figure 1-2 Sheets 1-& 2) is to be used at all times. For replacing the filter,
the container is also the wrench. The container/wrench is used to remove and replace the LIF from the
objective lens.
(3) Sacrificial Window - A replaceable sacrificial window (Figure 1-2, Sheet 4) is supplied to
protect the objective lens during operation in adverse conditions.
(4) IR Spot/Flood Lens This additional authorized item (AAL) (Figure 1-2, Sheet 4) focuses
the IR light for a narrow beam (spot) or wide-angle (flood) beam illumination.
1-10
TM 11-5855-262-23&P-2
TM 11-5855-262-23&P-2
TM 11-5855-262-23&P-2
1-13
TM 11-5855-262-23&P-2
1-14
TM 11-5855-262-23&P-2
1-10 LOCATION AND DESCRIPTION OF MAJOR COMPONENTS - Continued
(5) Compass This item (Figure 1-2, Sheets 1, 2 and 4) enables the operator to see azimuth
readings in the goggles viewing area. It is an AAL item for the AN/PVS-7B. It is a Component of End
Item (COEI) of the AN/PVS-7D.
(6) Tethering Cord This AAL item (Figure 1-2, Sheet 4) enables the user to attach the
compass or 3X-magnifier to his/herself to guard against dropping or losing these items.
(7) 3X Magnifier (AAL Item) The 3X magnifier (Figure 1-2, Sheet 4) is a lens assembly,
which can be added to the objective lens to extend the operators observation ranges.
b.
Headmount. The headmount (Figure 1-2, Sheets 1 and 2) secures the goggles to the
operators head for night viewing, and provides freehand support for use with a weapon, protective
mask or other purposes. It is adjustable and cushioned. The thin browpad used for large heads,
comes attached to the headmount and the thick or medium browpads are stored in the carrying case.
c.
Helmet Mount. The helmet mount secures the goggles to the Personal Armor System Ground
Troops (PASGT) helmet, allowing freehand support for use with a weapon, protective mask or other
purposes. The new helmet mount is made of a ruggedized metal. The old one is made of plastic. The
metal helmet mount is the only replacement available. There are four configurations of the helmet
mount. The old helmet mount (Figure 1-2, Sheet 1) attaches to the helmet using a strap and catch
assembly. The later two helmet mounts include a clip on/clip off feature, which allows for quick removal
and installation. The AN/PVS-7D helmet mount (Figure 1-2, Sheet 2) consists of a goggle mount and a
helmet mount bracket.
d.
Carrying Cases. The canvas carrying case is provided for transportation and protection of the
goggles, headmount, batteries and accessories. Two slide keepers are provided for belt attachment
and three D-rings for shoulder and leg strap attachment. A carrying case strap is also provided which
can be attached to the two D-rings on the back of the carrying case. There are two styles of carrying
cases. The old case (Figure 1-2, Sheets 1 and 3 of 4) has a hook and pile closure, and the new case
(Figure 1-2, Sheets 2 and 3 of 4) has a zipper closure.
e.
Shipping and Storage Case. The NVG are supplied in a shipping and storage case (Figure 12, Sheet 3 of 4). Batteries (not furnished) may be stored in the shipping and storage case.
NOTE
The MX-10130A image intensifier (not shown) used in the AN/PVS-7A
goggles will not work in the AN/PVS-7B and AN/PVS-7D.
1-15
TM 11-5855-262-23&P-2
1-11 CONFIGURATION OF IMAGE INTENSIFIER - Continued
ITEM
LIMITS
Interpupillary Distance
55 to 71 mm
Diopter Focus
+2 to -6 diopters
Objective Focus
25 cm to infinity
ITEM
DATA
Power Source
Battery (3 Vdc max)
Battery Requirements
1-16
TM 11-5855-262-23&P-2
1-12 EQUIPMENT DATA - Continued
Table 1-4. Mechanical Data.
ITEM
CHARACTERISTICS
ITEM
DATA
Magnification
1.0X (3X with magnifier)
Field-of-View
40 (13 with 3X magnifier)
Diopter Adjustment
+2 to -6 diopters
Focus Range
25 cm (7.9") to infinity
ITEM
DATA
1-17
TM 11-5855-262-23&P-2
Section III. Principles of Operation.
1-13 MECHANICAL FUNCTIONS
The mechanical functions of the goggles allow for differences in the physical features of individual
operators and provide for operating the NVG. These functions include the power switch, interpupillary
adjustment, eye relief adjustment, diopter adjustment, objective focus, IR spot/flood lens, compass
illumination button (underneath) and a latch, to attach or remove from mounts. The mechanical
controls are identified in Figure 1-4.
1-18
TM 11-5855-262-23&P-2
1-14 OPTICAL FUNCTIONS
The optical functions include an objective lens, an image intensifier, a collimator and two eyepiece
lenses (Figure 1-5). The objective lens collects light reflected from the night scene by the moon, stars,
or night sky, inverts the image and focuses that image on the image intensifier. The image intensifier
converts the captured light into a visible image, which is then split and re-inverted by the collimator and
transmitted to the eyepiece lenses for viewing.
1-19
TM 11-5855-262-23&P-2
1-15 ELECTRONIC CIRCUIT FUNCTIONS - Continued
ON Position
1-20
With the power switch in the OFF position, the circuit is not energized from
either the image intensifier or the IR source. Also, turn the power switch to this
position to rest after high light cut-off.
Power is drawn from the battery compartment to energize the goggles. When
the voltage drops to 2.4 Vdc, a low-battery indicator at the right eyepiece blinks
indicating approximately 30 minutes of operating time.
TM 11-5855-262-23&P-2
1-15 ELECTRONIC CIRCUIT FUNCTIONS - Continued
WARNING
The IR source is a light that is invisible to the unaided eye for use during
conditions of extreme darkness. However, the light from the IR source
can be detected by the enemy using night vision devices.
CAUTION
Do not use excessive force to place the power switch into the momentary
IR position.
NOTE
Some goggles contain an additional momentary IR function. For
momentary IR, continue to turn the power switch clockwise; past ON and
without pulling. The power switch will return to the ON position when
released.
IR/PULL Position
Power is drawn from the battery compartment to energize the goggles and IR
light source and a steady red indicator light in the left eyepiece.
c.
Automatic Shutoff. When the goggles are removed from the headmount or helmet mount while
in operation or flipped up in the mount, they will automatically shut off. To turn the goggles back on,
turn the power switch to RESET/OFF and then to ON again.
d.
High light Cut-off. The goggles will automatically cut off after 70 30 seconds of operation in
daylight or bright room light, except in fluorescent lighting. Individual bright lights (headlights,
flashlights, or other concentrated light sources) will not actuate the high light detector located on the
front of the goggles. To turn the goggles back on, turn the power switch to RESET/OFF position and
then to ON again.
1-21/22 blank
TM 11-5855-262-23&P-2
CHAPTER 2
UNIT MAINTENANCE INSTRUCTIONS
__________________________________________________________________________________
Page
Overview ......................................................................................................................2-1
Common Tools and Equipment ....................................................................................2-1
Special Tools, TMDE, and Support Equipment.............................................................2-2
Repair Parts .................................................................................................................2-2
Site and Shelter Requirements.....................................................................................2-2
Service Upon Receipt of Material .................................................................................2-2
Installation....................................................................................................................2-3
Preventive Maintenance Checks and Services (PMCS) Table .....................................2-3
Inspection Criteria for Proper Image Intensifier Operation ............................................2-3
Troubleshooting ...........................................................................................................2-3
Resolution Check Using the TS-4348/UV Test Set.......................................................2-3
Removal and Installation of Components .....................................................................2-3
Removal and Installation of Battery Cap Assembly and Battery Cap Retainer .............2-4
Removal and Installation of Browpads .........................................................................2-4
Removal and Installation of Neck Pad..........................................................................2-4
Removal and Installation of Chinstrap ..........................................................................2-6
Removal and Installation of Cross-strap .......................................................................2-6
Removal and Installation of Power Switch Knob...........................................................2-8
Removal and Installation of Magnet on Metal Helmet Mount ........................................2-8
Repainting and Refinishing Requirements..................................................................2-10
Lubrication Requirements ..........................................................................................2-10
Packing the NVG........................................................................................................2-10
OVERVIEW
This chapter contains maintenance procedures that are the responsibility of Unit Maintenance.
Operation instructions and operator maintenance can be found in TM 11-5855-262-10-2 and are not
repeated in this chapter.
The Unit level tasks include routine inspections, cleaning, visual inspection of image intensifier
performance, optional resolution test using the TS-4348/UV test set, and repair by removing and
replacing the headmount, headmount straps, and browpads, helmet mount, carrying case, sacrificial
window, demist shields, neck cord, eyecups, objective lens cap, battery cap, IR spot/flood lens, and
compass.
Section I. Repair Parts, Tools, Special Tools, TMDE, and Support Equipment.
2-1 COMMON TOOLS AND EQUIPMENT
For authorized common tools and equipment, refer to the Modified Table of Organization and
Equipment (MTOE), CTA 50-970, or CTA 8-100, as applicable to your unit.
2-1
TM 11-5855-262-23&P-2
2-2 SPECIAL TOOLS, TMDE, AND SUPPORT EQUIPMENT
Refer to Appendix B for the Maintenance Allocation Chart (MAC) for authorized maintenance and to
Appendix C for the Repair Parts and Special Tools List (RPSTL) for information on special tools, Test,
Measurement, and Diagnostic Equipment (TMDE), and support equipment required at unit
maintenance. In addition, instructions or a fabricated black spot test fixture are contained in Appendix
E.
2-2
TM 11-5855-262-23&P-2
2-6 INSTALLATION
Installation instructions are contained in TM 11-5855-262-10-2; Operator's Manual for Night Vision
Goggles (NVG), AN/PVS-7B and AN/PVS-7D.
TM 11-5855-262-23&P-2
2-12 REMOVAL AND INSTALLATION OF BATTERY CAP AND BATTERY CAP RETAINER
Inspect battery cap, retainer and O-ring for damage or loss. If damaged or missing, replace battery
cap/ battery cap retainer or O-ring per following:
(1)
(2)
Inspect battery cap for damage or corrosion, clean and/or replace as necessary.
(3)
CAUTION
If wired body pin is broken, turn in to Direct Support.
(b) Examine the battery housing for the presence of a link around the pin between the
rear cover and the battery housing. If a link is present it must be removed by carefully clipping with wire
cutters - do not cut the pin. Examine the pin between the rear cover and the battery housing. If the pin
is missing or damaged - turn the goggles over to direct support. If the pin is present, slide a sleeve
onto the wire, insert one end of the wire around the pin, and then back down through the sleeve. Align
the sleeve and the wire so that the sleeve is approximately one-eighth inch away from the pin and oneeighth inch of the short end of the wire protrudes from under the sleeve. Once positioned, crimp the
sleeve with needle nose pliers, so that the sleeve firmly holds both parts of wire in place. Repeat the
process at the other end of the wire around the battery cap stud.
(1)
browpad.
Remove old browpad (Figure 2-1) by grasping the headband and peeling off the old
(2) Replace browpad by gently pressing on the new browpad and smoothing out any wrinkles
in new browpad.
(1)
Remove vertical adjustment (Figure 2-1) from sliding bar buckle at rear of neck pad.
(2) Remove right chinstrap from sliding bar buckle on right side of neck pad. Remove left
snap assembly from left side of neck pad.
(3)
Unlace neck pad straps (Figure 2-2) from strap retaining tabs in headband (Figure 2-1).
(4) Replace neck pad by lacing straps as shown in Figure 2-2. Lift upper strap retention tab to
allow neck pad strap to be inserted into fastener area.
2-4
TM 11-5855-262-23&P-2
2-14 REMOVAL AND INSTALLATION OF NECK PAD - Continued
(5) Slip neck pad strap under upper strap retention tab. Straighten strap, pulling strap under
lower strap retention tab.
(6)
Repeat steps (4) and (5) for the other side of the neck pad and headband.
TM 11-5855-262-23&P-2
2-14 REMOVAL AND INSTALLATION OF NECK PAD - Continued
(1) Remove chinstrap (Figure 2-1) by unsnapping the two snaps from the left side of the
headband and neck pad. Unbuckle the chinstraps from narrow strap assembly and the right side of
neck pad.
(2) Replace the chinstrap by installing the two snaps on the left side of the headband and
neck pad. Lace the two right straps into their respective sliding bar buckles on the right side of the
headband and neck pad for correct lacing. (Figure 2-3)
(1)
(2)
(3) Remove cross-strap front strap from headband (Figure 2-1) by unthreading strap from
headband slots.
(4) Slide strap free of headband by sliding the left and right strap loops off at rear of
headmount.
2-6
TM 11-5855-262-23&P-2
2-16 REMOVAL AND INSTALLATION OF CROSS-STRAP - Continued
NOTE
The elastic straps should be on top of the vertical adjustment strap when
headmount is properly installed.
(5) Replace cross-strap by installing the left and right strap loops onto the headband. Thread
cross-strap front strap through front top headband slot from inside headband. Pull strap out and thread
back through bottom slot.
(7)
Attach chinstrap right rear strap to right sliding bar buckle on neck pad.
(8)
Attach chinstrap assembly (Figure 2-1) left rear snap to mating fastener on neck pad.
(9) Attach cross-strap vertical adjustment into mating sliding bar buckle attached to center
outside of neck pad.
(10) Replace browpad (para 2-13).
2-7
TM 11-5855-262-23&P-2
2-17 REMOVAL AND INSTALLATION OF POWER SWITCH KNOB
The power switch knob can be replaced without disturbing any of the goggles assemblies. One lock
pin secures the knob to the shaft.
__________________________________________________________________________________
INITIAL SETUP
Test Facility
Standard workbench in the electronic repair service area
Tools
Hex wrench .050", (Appendix B, Item 11)
Materials/Parts
Power Switch Knob (Appendix C, Figure C-2, Item 12)
__________________________________________________________________________________
REMOVAL
(1)
With a hex wrench .050", remove knob lock pin by turning counterclockwise.
(2)
INSTALLATION
(1)
Position knob on switch shaft. Align lock pin hole in knob with lock pin hole in shaft.
(2)
Insert lock pin into knob and use a hex wrench .050" to tighten lock pin hand tight.
INITIAL SETUP
Test Facility
Standard workbench in the electronic repair service area
Tools
Hex wrench 5/64", (Appendix B, Item 11)
Materials/Parts
None
2-8
TM 11-5855-262-23&P-2
2-18 REMOVAL AND INSTALLATION OF MAGNET ON METAL HELMET MOUNT Continued
REMOVAL
(1)
With the 5/64". hex wrench, remove the two screws located behind the socket.
(2)
INSTALLATION
(1) Position the magnet by aligning with the holes in the metal helmet mount and insert the
two screws (Figure 2-4).
(2)
Use the 5/64". hex wrench to tighten the two screws hand tight.
2-9
TM 11-5855-262-23&P-2
2-19 REPAINTING AND REFINISHING REQUIREMENTS
Unit maintenance personnel are not authorized or required to repaint or refinish any component of the
goggles, accessories, carrying case or shipping and storage case.
2-10
TM 11-5855-262-23&P-2
CHAPTER 3
DIRECT SUPPORT MAINTENANCE INSTRUCTIONS
__________________________________________________________________________________
Page
Overview ......................................................................................................................3-1
Common Tools and Equipment ....................................................................................3-1
Special Tools, TMDE, and Support Equipment.............................................................3-1
Repair Parts .................................................................................................................3-2
Site and Shelter Requirements.....................................................................................3-2
Service Upon Receipt of Material .................................................................................3-2
Scope...........................................................................................................................3-2
Troubleshooting ...........................................................................................................3-3
TS-3895A/UV Preparation for Use ...............................................................................3-6
Testing the NVG Using TS-3895A/UV..........................................................................3-6
Electrical Troubleshooting ..........................................................................................3-10
Black Spot Check.......................................................................................................3-12
Removal and Installation of Objective Lens................................................................3-17
Objective Lens Infinity Focus Adjustment ...................................................................3-20
Removal and Installation of Image Intensifier .............................................................3-20
Removal and Installation of Collimator .......................................................................3-22
Removal and Installation of Wired Housing ................................................................3-26
Removal and Installation of Rear Cover .....................................................................3-28
Purging.......................................................................................................................3-29
Operational Checks....................................................................................................3-33
Packing the NVG........................................................................................................3-33
Shipping the Image Intensifier ....................................................................................3-33
OVERVIEW
Direct support maintenance personnel are authorized by the Maintenance Allocation Chart (MAC) to
perform inspection, repair, and replacement procedures to return the goggles to operational status.
Section I. Repair Parts, Tools, Special Tools, TMDE, and Support Equipment.
3-1 COMMON TOOLS AND EQUIPMENT
For authorized common tools and equipment, refer to the Modified Table of Organization and
Equipment (MTOE), CTA 50-970, or CTA 8-100, as applicable to your unit.
3-1
TM 11-5855-262-23&P-2
3-3 REPAIR PARTS
Repair parts required by Direct Support Maintenance to maintain the NVG are listed and illustrated in
Appendix C.
180-Day Servicing.
(1) PMCS Refer to TM 11-5855-262-10-2, Operator's Manual for Night Vision Goggles
(NVG), AN/PVS-7B and AN/PVS-7D.
(2)
(3) Resolution test For the TS-4348/UV, refer to TM 11-5855-262-10-2, Operator's Manual
for Night Vision Goggles (NVG), AN/PVS-7B and AN/PVS-7D. For the TS-3895A/UV, refer to
paragraph 3-9.
3-2
TM 11-5855-262-23&P-2
Section IV. Troubleshooting.
3-7 TROUBLESHOOTING
CAUTION
Maintenance for the NVG should be performed in an environment, which
is as dust free as possible to protect optical assemblies and the image
intensifier.
a.
Purpose of Troubleshooting. Troubleshooting is required to isolate and identify defective
assemblies in the NVG. Troubleshooting consists of performing inspections and operational checks to
determine the symptom of the malfunction. The direct support troubleshooting table is then used to
determine the probable cause, further troubleshooting instructions, and the required corrective action.
Image intensifier malfunctions can be determined by using the TS-3895A/UV test set to assess image
intensifier stability and resolution at high and low-illumination levels. Electrical troubleshooting consists
of using a standard multimeter to determine failures in the wired housing, which could result in lack of
power to the image intensifier.
b.
Direct Support Troubleshooting. Table 3-1 is to be used as a guide for systematic and
efficient procedures to isolate malfunctions in the goggles. This table cannot list all the malfunctions
that may occur, all the tests and inspections needed to find the fault, or all the corrective actions
needed to correct the fault. If the equipment malfunction is not listed or actions listed do not correct the
fault, notify your supervisor.
CAUTION
Before proceeding with any corrective action, confirm that the goggles or
image intensifier is out of the warranty period. Failure to utilize warranty
coverage will result in excess charges to the unit (para 1-7).
PROBLEM
PROBABLE CAUSE
CORRECTIVE ACTION
TM 11-5855-262-23&P-2
3-7 TROUBLESHOOTING - Continued
Table 3-1. Troubleshooting - Continued.
PROBLEM
PROBABLE CAUSE
CORRECTIVE ACTION
Refocus eyepiece.
Moisture in lenses.
Interpupillary adjustment
Rear cover needs lubrication.
Remove rear cover and grease
cannot be made.
inside of rear cover with light
coat of grease (para 3-17).
Defective rear cover.
3-4
TM 11-5855-262-23&P-2
3-7 TROUBLESHOOTING - Continued
Table 3-1. Troubleshooting - Continued.
PROBLEM
PROBABLE CAUSE
CORRECTIVE ACTION
IR illumination indicator
not operative.
LED dislodged.
Defective low-battery
detection capability.
LED dislodged.
Refocus eyepiece.
TM 11-5855-262-23&P-2
3-7 TROUBLESHOOTING - Continued
Table 3-1. Troubleshooting - Continued.
PROBLEM
PROBABLE CAUSE
CORRECTIVE ACTION
Goggles fail resolution test. (Cont)
NOTE
Before using the TS-3895A/UV, refer to TM 11-5855-264-14, to
familiarize yourself with the operation, warnings, and cautions associated
with that test equipment.
INITIAL SETUP
Test Facility
Clean station in the electronic repair service area
Tools
None
Equipment
Test Set TS-3895A/UV (Appendix B, Item 2)
Dispenser, Alcohol (Appendix D, Item 5)
Materials/Parts
Cotton-tipped applicators (Appendix D, Item 10)
Isopropyl alcohol (Appendix D, Item 1)
__________________________________________________________________________________
PROCEDURE
(1)
(2) Clean the objective and eyepiece lenses of the goggles with cotton-tipped applicators and
isopropyl alcohol.
3-6
TM 11-5855-262-23&P-2
3-9 TESTING THE NVG USING TS-3895A/UV -Continued
(3)
(4)
Ensure that the test port lenses of the test set are clean and free of dirt.
(5)
Attach the large goggle adapter to either test port and cover other test port.
Attach the goggles to the test set by inserting the objective lens into the adapter (Figure 3-
2).
3-7
TM 11-5855-262-23&P-2
3-9 TESTING THE NVG USING TS-3895A/UV -Continued
Do not reject goggles for resolution unless your eyes have been
adequately dark-adapted.
(1)
Turn the selector switch to the LOW LIGHT RESOLUTION (yellow) position (Figure 3-1).
(2)
(3)
Turn off the room lights and let your eyes adjust to the dark.
(4)
(5) Focus the objective lens and then the eyepiece lenses for best focus to obtain the
sharpest image.
3-8
TM 11-5855-262-23&P-2
3-9 TESTING THE NVG USING TS-3895A/UV -Continued
(6) Look for flashing, flickering, instability, emission points, or edge glow, refer to (TM 115855-262-10-2). If any unacceptable conditions are noted, replace the image intensifier (para 3-14).
(7) Now observe the test pattern. You must be able to distinguish all three horizontal lines
and all three vertical lines to count seeing the Element (Figure 3-3). You must be able to see Element
3 on the bottom of the test pattern for the NVG to pass.
Turn the selector switch to the HIGH LIGHT RESOLUTION (blue) position (Figure 3-1).
(2)
(3) Look for flashing, flickering, shading, or bright spots, refer to (TM 11-5855-262-10-2). If
any unacceptable conditions are noted, replace the image intensifier (para 3-14).
(4) Now observe the test pattern. You must be able to distinguish all three horizontal lines
and all three vertical lines to count seeing the Element (Figure 3-4). You must be able to see Element
3 on the top of the test pattern for the NVG to pass.
(5) If the goggles fail, recheck the objective lens and eyepiece lens focus to make sure you
have the sharpest image.
(6)
3-9
TM 11-5855-262-23&P-2
3-9 TESTING THE NVG USING TS-3895A/UV -Continued
(2)
(3)
With known good batteries in battery compartments, position power switch to ON.
(4) Apply test probes to the tube contact pins (Figure 3-5). The red test probe goes to positive
(+) pin and black test probe goes to negative () pin.
NOTE
Perform voltage check within 70 30 seconds as high light cut-off circuit
will activate in bright daylight or room light but not in fluorescent lighting.
Set power switch to RESET/OFF position to reset goggles if high light cutoff occurs.
3-10
TM 11-5855-262-23&P-2
3-10 ELECTRICAL TROUBLESHOOTING-Continued
NOTE
Confirm the goggles or image intensifier is out of the warranty period
before replacing the image intensifier (para 1-7).
(5) If 2.5 Vdc to 3.2 Vdc is present, replace image intensifier (para 3-14).
incorrect, remove and replace wired housing (para 3-16).
If voltage is
3-11
TM 11-5855-262-23&P-2
3-11 BLACK SPOT CHECK
Black spots are cosmetic blemishes and do not affect reliability. Generally, you can assume that the
black spot was there during acceptance testing. However, occasionally the need may arise to verify the
location, size, and number of spots. This test allows the maintainer to evaluate possible out-ofspecification black spots, dark spots, or opaque spots in the image area against the specifications for
the image intensifier.
__________________________________________________________________________________
INITIAL SETUP
Test Facility
Dark room
Tools
Measuring tape, (Appendix B, Item 13)
3-volt incandescent flashlight or smaller, (Appendix B, Item 11)
Equipment
Black spot target (Appendix E, Item 1)
Light source: LED on any other system such as AN/PVS-5X, or an AN/PVS-7X, or an IR light
transmitter (Appendix B, Item 10)
Tripod or fabricated Black Spot Target Test Fixture (Appendix E, Items 2-8)
Dispenser, alcohol (Appendix D, Item 5)
Materials/Parts
Cotton-tipped applicators (Appendix D, Item 10)
Isopropyl alcohol (Appendix D, Item 1)
NOTE
You will need a flashlight filter, to read this procedure while in the
darkened area.
__________________________________________________________________________________
3-12
TM 11-5855-262-23&P-2
3-11 BLACK SPOT CHECK - Continued
LIGHTS ON
(1)
3-13
TM 11-5855-262-23&P-2
3-11 BLACK SPOT CHECK - Continued
(2)
Position the Black Spot Chart so the center ring is at eye level during testing.
(3) Clean the objective and eyepiece lenses of the systems to be tested by using isopropyl
alcohol and cotton-tipped applicators. Moisten the applicator with the alcohol and use circular motions
beginning at the center of the lens and moving in larger circles to the outside of the lens.
(4) Position the goggles to be tested on the tripod or test fixture and secure it. The front
surface of the objective lens of the goggles should be exactly 30 inches from the target at height of the
center ring.
(5) Position the light source behind, to the left, right, top, or bottom of the tripod to prevent
shadows on the targets. Make sure that your position when looking through the goggles does not
produce shadows on the target.
LIGHTS OFF
NOTE
The following test must be performed in a darkened area. Your eyes
must be dark-adapted to perform this test. It takes approximately 10
minutes to become properly dark-adapted for low light resolution
evaluation. However, if you have just been exposed to bright sunlight,
dark adaptation will take longer.
(1)
(2)
(3) Check the dark room for light leaks using another set of NVG (AN/PVS-5X or AN/PVS-7X)
and eliminate any leaks you find. Follow good dark room techniques.
(4) Turn on the light source and look through the goggles. Uniformly illuminate the target by
moving the light source closer or farther from the target. Eliminate any shadows.
(5) Alternately adjust the objective focus and diopter setting, AT THE WORKING DISTANCE,
until the best focus is achieved. You must have the proper focus and the exact working distance of 30
inches from the front surface of the objective lens to achieve correct results.
(6) Look at the edge of the spots in the center ring, and move the light source forward or back
for the best spot contrast. Remember to refocus the objective each time you view a different ring of the
chart.
(7) Use the flashlight to recheck the exact position of the goggles at 30 inches (1 inch). This
distance from the target to the objective is critical and must be maintained during testing.
TEST METHOD
(1) Center the view so it is concentric with the test target rings. (The dotted line represents a
circle of 17.5 mm on the cathode surface of the image intensifier). Use the lines to the left and right of
the outer circle to accomplish this.
(2)
3-14
TM 11-5855-262-23&P-2
3-11 BLACK SPOT CHECK - Continued
NOTE
The total diameter of each image intensifier may vary between 17.5 mm
and 18.5 mm. Evaluate only those black spots in the area of the image
inside the 17.5 mm circle. The dotted line in the second ring marks this
17.5 mm area. Spots that are located outside the dotted circle are not a
cause for rejecting the image intensifier.
(3)
Identify the ring of the chart that bounds the black spot you are evaluating.
(4)
Refocus the objective for the best focus on the ring of the chart identified above.
(5)
Using the allowable spot-size chart in that particular ring, determine the size of the black
spot.
NOTE
Circular spots will correspond easily to this chart. However, irregular
(non-circular) spots require you to judge the area of the spot in question
against the area of the circular spot on the chart.
(6)
Count the number of spots, by spot size, in each ring and record these figures.
PASS/FAIL CRITERIA
(1) Refer to Tables 3-2 and 3-3 for a listing of allowable spots and sizes to determine if the
image intensifier under test should be rejected.
SIZE AND
.003
.006
.009
.012
LARGER
SMALLER
LOCATION
.006
.009
.012
.015
THAN .015
THAN .003
Center Ring
3
1
0
0
0
any amount
1st Ring
35
9
5
1
0
any amount
2nd Ring
35
23
8
2
0
any amount
SIZE AND
.003
.006
.009
.012
LARGER
SMALLER
LOCATION
.006
.009
.012
.015
THAN .015
THAN .003
Center Ring
0
0
0
0
0
any amount
1st Ring
2
1
0
0
0
any amount
2nd Ring
2
1
0
0
0
any amount
3-15
TM 11-5855-262-23&P-2
3-11 BLACK SPOT CHECK - Continued
(2) The image intensifier fails if the black spot (circular) is larger than the maximum spot size
indicated on the chart for the ring in which the spot (circular) is located, or if the number of spots
exceeds the number of spots allowed for that ring.
(3) The image intensifier fails if the maintenance person determines, by comparison, that the
area of the non-circular spot is larger than the area of the largest circular spot designated in that ring.
This will be a subjective evaluation so remember that these spots were evaluated before Government
acceptance at the contractors plant and passed. Judging the area is difficult. See Examples 1 and 2
of Figure 3-8. Do not reject an image intensifier for an irregularly shaped spot by its diameter alone.
(4) Consider two spots and the distance between them as one spot anytime that this distance
between the two spots is less than the diameter of either spot. The image intensifier fails if this total
dimension (diameter) is greater than the allowable spot size diameter for the ring in which the spots are
located.
(5) A shaded area may surround a black spot. Consider the shaded area as part of the spot if
the high light level resolution chart cannot be read through the shaded area (DS is to determine using
the TS-3895A/UV). The image intensifier fails if the combined area of the spot and the shaded area
exceed the maximum area of the largest spot for the ring in which the spot is located.
(6) Do not reject an image intensifier for a black spot that is located outside the dotted ring on
the black spot chart.
3-16
TM 11-5855-262-23&P-2
3-11 BLACK SPOT CHECK - Continued
NOTE
If an image intensifier is rejected on the basis of this test for black spots,
do not immediately reject the system for a defective image intensifier. It
is possible that some of the spots may be caused by contamination inside
the goggles and on the surfaces of the optics. You must disassemble the
goggles and clean and inspect for dirt, debris, fingerprints, or other
foreign material. Reassemble the goggles and recheck the image area
for black spots.
CAUTION
To prevent damage to threads, do not use excessive force when rethreading the objective lens onto the wired housing.
__________________________________________________________________________________
INITIAL SETUP
Test Facility
Clean station in the electronic service area
Tools
Slip joint pliers (Appendix B, Item 8)
Dispenser, alcohol (Appendix D, Item 5)
3-17
TM 11-5855-262-23&P-2
3-12 REMOVAL AND INSTALLATION OF OBJECTIVE LENS - Continued
Materials/Parts
Objective lens (Appendix C, Fig. C-2 Item 1)
O-ring (Appendix C, Fig. C-2 Item 2)
Lubricant (silicone grease), (Appendix D, Item 2)
Cotton-tipped applicators (Appendix D, Item 10)
Isopropyl alcohol (Appendix D, Item 1)
Sealing compound (Appendix D, Item 8)
__________________________________________________________________________________
NOTE
Confirm the NVG is out of the warranty period before replacing the
objective lens (para 1-7).
REMOVAL
(1) With objective lens (Figure 3-9) facing technician, rotate objective lens counterclockwise
and remove lens from threaded part of wired housing. Be careful not to disturb location of image
intensifier in wired housing.
(2)
INSTALLATION
(1) Thoroughly clean all optical surfaces with cotton-tipped applicators and isopropyl alcohol
or compressed air. Mating surfaces should be cleaned with clean lint-free cloths and isopropyl alcohol
before assembly. If damaged, replace with new objective lens (Figure 3-9).
(2)
Apply a light coating of lubricant on O-ring before inserting into groove in objective lens.
CAUTION
Be careful not to spread lubricant on optical surfaces, which will be
difficult to reclean.
(3) Carefully thread objective lens clockwise onto wired housing.
intensifier is properly in place. Do not tighten.
3-18
(4)
(5)
TM 11-5855-262-23&P-2
3-12 REMOVAL AND INSTALLATION OF OBJECTIVE LENS - Continued
TM 11-5855-262-23&P-2
Perform Initial Setup, Procedure, and low light resolution test (para 3-9).
(3)
(4) With the objective lens facing away from the operator, rotate objective lens fully clockwise.
Using a pair of slip-joint pliers (Appendix B, Item 8), loosen infinity focus lock ring (Figure 3-9) by
turning lock ring fully counterclockwise. Using a cotton-tipped applicator moistened with isopropyl
alcohol, clean away excess sealing compound. If necessary, rotate objective lens lock ring back and
forth to help clean out the threads.
(5) Focus the objective lens by rotating objective focus ring counterclockwise slightly past best
focus (image begins to blur) of the resolution pattern shown in Figure 3-3.
(6) Maintain objective focus setting and use your fingers to rotate infinity focus lock ring
(Figure 3-11) clockwise until ring just contacts the objective focus knob.
CAUTION
Applying too much sealing compound, will damage parts.
(7) Apply one drop of sealing compound (Appendix D, Item 8) on threads at rear of infinity
focus lock ring 90 degrees apart (Figure 3-9). Allow 10 minutes for sealing compound to cure.
INITIAL SETUP
Test Facility
Clean station in the electronic repair service area
Tools
None
3-20
TM 11-5855-262-23&P-2
3-14 REMOVAL AND INSTALLATION OF IMAGE INTENSIFIER - Continued
Materials/Parts
Image intensifier (Appendix C, Figure C-2, Item 3)
Cotton-tipped applicators (Appendix D, Item 10)
Isopropyl alcohol (Appendix D, Item 1)
__________________________________________________________________________________
WARNING
Toxic Material
The image intensifiers phosphor screen contains toxic materials.
If an image intensifier breaks, be extremely careful to avoid inhaling the phosphor screen
material. Do not allow the material to come in contact with the mouth or open wounds on
the skin.
If the phosphor screen material contacts your skin, wash it off immediately with soap and
water.
If you inhale/swallow any phosphor screen material, drink a lot of water, induce vomiting,
and seek medical attention as soon as possible.
NOTE
Confirm the image intensifier is out of the warranty period before
replacing the image intensifier. If in the warranty period (para 1-7). If not
in the warranty period (para 3-21).
REMOVAL
(1)
CAUTION
Handle image intensifier gently to prevent damage. Set image intensifier
only on contact end. Treat suspected defective image intensifiers as
though they are good so they are not damaged when returned to Defense
Reutilization and Marketing Office (DRMO).
(2) Gently ease out image intensifier from within wired body housing. Pull out straight forward
from housing.
(3)
If image intensifier is not defective, wrap in lens paper to protect and store in a clean dry
place.
INSTALLATION
(1)
TM 11-5855-262-23&P-2
3-14 REMOVAL AND INSTALLATION OF IMAGE INTENSIFIER - Continued
CAUTION
NOTE
Retain packaging material for use when returning defective image
intensifiers to DRMO.
(2)
Clean both ends of image intensifier with cotton-tipped applicators and isopropyl alcohol.
(3) Slide the image intensifier (Figure 3-9), contacts end first, into the opening of the wired
housing so the groove on the side of the image intensifier engages the ridge inside the opening of the
wired housing.
(4)
(5)
INITIAL SETUP
Test Facility
Clean station in the electronic repair service area
Tools
Screwdriver, cross-tipped, (Appendix B, Item 11)
Jeweler's file
Dispenser, alcohol (Appendix D, Item 5)
3-22
TM 11-5855-262-23&P-2
3-15 REMOVAL AND INSTALLATION OF COLLIMATOR - Continued
Materials/Parts
Collimator (Appendix C, Figure C-2, Item 15)
Tape, black, 1/2-inch, (Appendix B, Item 11)
Cotton-tipped applicators (Appendix D, Item 10)
Isopropyl alcohol (Appendix D, Item 1)
__________________________________________________________________________________
NOTE
Confirm the goggles are out of the warranty period before replacing the
collimator (para 1-7).
REMOVAL
(1)
(2)
Remove image intensifier (para 3-14). Store in clean dry place if not damaged.
CAUTION
To prevent damage to collimator during removal, set eyepiece
interpupillary distance to maximum.
(3) With front of wired housing (Figure 3-9) facing you, remove two screws and two washers
which secure the collimator in the wired housing.
(4) Carefully remove the collimator from the wired housing. If the collimator is not defective,
store in a clean dry place.
INSTALLATION
NOTE
To complete the collimator installation, you will need to make a straight
black line on the wall or a light-colored piece of wood or cardboard. Place
a 2-foot strip of 1/2-inch black tape horizontally across the center of the
board or on the wall about 2 to 4 inches above table height. Make sure
the taped line is straight.
(1)
CAUTION
To prevent damage to eyepieces during installation, set eyepiece
interpupillary distance to maximum.
3-23
TM 11-5855-262-23&P-2
3-15 REMOVAL AND INSTALLATION OF COLLIMATOR - Continued
(2)
(3) Looking at the eyepiece end of the wired housing, turn the diopter focus rings fully
counterclockwise so the eyepieces are extended all the way out.
(4) Place the collimator, prism end first, into the opening of the wired housing. Align the
raised notch of the wired housing with the slot on the side of collimator (Figure 3-10).
NOTE
The collimator will only move a very small amount.
(6) Position a table or bench so one end is 58 inches from the collimation line. The line
should be within 4 inches of the height of the tabletop. Make sure the tabletop is parallel to the line. As
shown in Figure 3-11, rest the eyepiece flanges on end of the tabletop so the diopter adjust rings butt
against the vertical edge.
3-24
TM 11-5855-262-23&P-2
3-15 REMOVAL AND INSTALLATION OF COLLIMATOR - Continued
3-25
TM 11-5855-262-23&P-2
3-15 REMOVAL AND INSTALLATION OF COLLIMATOR - Continued
(12) Install the objective lens (para 3-12).
(13) Purge the goggles (para 3-18).
INITIAL SETUP
Test Facility
Clean station in the electronic repair service area
Tools
Screwdriver, cross-tipped (Appendix B, Item 11)
Dispenser, alcohol (Appendix D, Item 5)
Materials/Parts
Wired Housing (Appendix C, Figure C-2, Item 13)
O-ring (Appendix C, Figure C-2, Item 10)
Lubricant (silicone grease), (Appendix D, Item 2)
Cotton-tipped applicators (Appendix D, Item 10)
Isopropyl alcohol (Appendix D, Item 1)
__________________________________________________________________________________
NOTE
Confirm the goggles are out of the warranty period before replacing the
wired housing (para 1-7).
REMOVAL
(1)
(2)
Remove image intensifier (para 3-14). Store in clean dry place if not defective.
CAUTION
To prevent damage to eyepiece, during rear cover removal, set eyepiece
interpupillary distance to maximum.
3-26
TM 11-5855-262-23&P-2
3-16 REMOVAL AND INSTALLATION OF WIRED HOUSING - Continued
(3)
(4)
housing.
CAUTION
To prevent damage to flex harness inside wired housing, gently separate
the rear cover from the wired housing.
(5) Carefully remove the two LED assemblies from the diopter cell assemblies, freeing rear
cover from wired housing and its flex harness.
(6) Remove O-ring from around rear cover. Remove battery cap and battery cap retainer link
(para 2-12) from the wired housing.
(7)
(8)
(9) Store wired housing, rear cover, O-ring, battery cap, battery cap retainer link, neck cord,
and objective lens cap in clean dry place.
INSTALLATION
(1)
(2) Apply a light coating of lubricant ( Appendix D, Item 2); to the O-ring (Figure 3-9) and
install in groove around rear cover.
CAUTION
To prevent damage to eyepiece during cover installation, set eyepiece
interpupillary distance to maximum.
(3) Clean diopter cell assemblies with cotton-tipped applicators and isopropyl alcohol if
necessary, carefully install the LED assemblies on flex harness into each diopter cell and the battery
cap and battery caps retainer kit on securing pin on wired housing.
CAUTION
Make sure the O-ring is completely in its groove or it will be pinched and
damaged when rear cover is installed on wired housing.
(4)
(5) Install eight screws and eight washers that secure rear cover to wired housing. Check for
pinching of O-ring before tightening and securing screws.
(6)
3-27
TM 11-5855-262-23&P-2
3-16 REMOVAL AND INSTALLATION OF WIRED HOUSING - Continued
(7)
(8)
(9)
(10) Reinstall the neck cord and objective lens cap (para 2-11).
(11) Reinstall the battery cap and battery cap retaining link (para 2-12).
NOTE
Be sure that the data plate is removed from the old wired housing and
placed on the new assembly.
INITIAL SETUP
Test Facility
Clean station in the electronic repair service area
Tools
Screwdriver, cross-tipped (Appendix B, Item 11)
Dispenser, alcohol (Appendix D, Item 5)
Materials/Parts
Rear Cover (Appendix C, Figure C-2, Item 9)
O-ring (Appendix C, Figure C-2, Item 10)
Lubricant (silicone grease), (Appendix D, Item 2)
Cotton-tipped applicators (Appendix D, Item 10)
Isopropyl alcohol (Appendix D, Item 1)
__________________________________________________________________________________
NOTE
Confirm the goggles are out of the warranty period before replacing the
rear cover (para 1-7).
REMOVAL
(1)
3-28
With the eyepieces facing you, gently remove eyecups (Figure 3-9) from rear cover.
TM 11-5855-262-23&P-2
3-17 REMOVAL AND INSTALLATION OF REAR COVER - Continued
CAUTION
(2)
CAUTION
The wired housing is attached to the rear cover. To prevent damage to
flex harness inside wired housing, gently separate rear cover from the
wired housing.
(3) Carefully remove the two LED assemblies from the diopter cell assemblies, freeing rear
cover from wired housing and flex harness.
(4) Remove O-ring from rear cover. Remove the battery cap and battery cap retainer (para 212) after separating the rear cover from the wired housing.
INSTALLATION
CAUTION
To prevent damage to the collimator during assembly, set eyepiece
interpupillary distance to maximum.
(1) Apply a light coating of lubricant on O-ring (Figure 3-9) before inserting it into groove in
rear cover and if necessary apply a light coating of lubricant to the inside back cover of the rear cover.
CAUTION
Be careful not to spread lubricant on optical surfaces, which will be
difficult to reclean.
(2) Clean diopter cell and collimator assemblies with cotton-tipped applicators and isopropyl
alcohol or compressed air as necessary.
(3) Carefully install LED assemblies on flex harness into each diopter cell. Reinstall battery
cap and battery cap retainer before closing rear cover against wired housing.
(4) Install eight screws and eight washers which secure rear cover to wired housing. Check
for pinching of O-ring before tightening securing screws.
(5)
With eyepieces facing you, gently push the eyecups on the eyepieces.
(6)
3-18 PURGING
The housing of the NVG (Figure 3-9) is filled with dry nitrogen and sealed to prevent dirt and moisture
from degrading the optical performance during use. Perform the following procedure to purge the
goggles.
3-29
TM 11-5855-262-23&P-2
TM 11-5855-262-23&P-2
3-18 PURGING - Continued
INITIAL SETUP
Test Facility
Clean station in the electronic repair service area
Tools
Screwdriver, flat tipped (Appendix B, Item 11)
Wrench (Appendix B, Item 12)
Equipment
Purge device (Appendix B, Item 5), or commercial equivalent
Fire Control Purging Kit (Appendix B, Item 9)
Purge Adapter (Appendix B, Item 7), or commercial equivalent
Quick Disconnect (optional, commercially available)
Materials/Parts
Nitrogen, Compression type: water pumped
Composition and percentage: 99.5% nitrogen by volume (Appendix D, Item 4),
or commercial equivalent
O-ring (Appendix C, Figure C-2, Item 8)
Lubricant (silicone grease), (Appendix D, Item 2)
References
TM 750-116, General Procedures for Purging and Charging of Fire Control Instruments
__________________________________________________________________________________
WARNING
Personnel Injury
Serious injury may result if the nitrogen tank valve breaks off due to
tank upset. If the tank valve breaks, the tank can be propelled by the
escaping gas and strike you or others.
Always secure the tank to an upright support before removing the tank
valve guard and attaching the regulator valve to the tank.
__________________________________________________________________________________
3-31
TM 11-5855-262-23&P-2
3-18 PURGING Continued
(1) Connect fire control purging kit, using a wrench , or equivalent, to nitrogen tank and purge
device as shown in Figure 3-13 and in accordance with TM 750-116.
(2)
(3)
control.
(4)
Remove purge screw and O-ring from the purge port of the goggles.
CAUTION
Do not over tighten purge adapter to prevent damage to O-ring seat.
(5)
Thread purge adapter approximately three turns into the purge port of the goggles.
(6)
Attach hose of purge device to quick disconnect, if present, and into purge adapter.
(7) Open nitrogen tank valve. The high pressure gauge will indicate tank pressure. If the
pressure is below 100 pounds, replace tank.
(8) Set purge device PUMP/NITROGEN switch to PUMP and the LEAK TEST/PURGE switch
to PURGE.
(9) Slowly adjust regulator valve handle by turning it clockwise until low-pressure gauge
indicates 3 to 3.5 psi.
(10) Pump vacuum handle of the purge device until purge device gauge indicates greater than
15 in. Hg (Mercury).
(11) Purge goggles by positioning purge device PUMP/NITROGEN switch to NITROGEN and
observe that the purge device gauge indicates 3 to 3.5 psi. If necessary, slowly adjust regulator valve
handle until purge device gauge reaches 3 to 3.5 psi.
(12) Repeat steps 8, 10, and 11 one additional time.
(13) Turn PUMP/NITROGEN switch to PUMP.
3-32
TM 11-5855-262-23&P-2
3-18 PURGING - Continued
(14) Set regulator valve handle for zero.
(15) Turn off nitrogen tank valve.
NOTE
Purging the goggles is not intended to result in a positive pressure inside
the housing. Consequently, it is okay to leave the purge port open briefly
after removing the purge adapter and purge device hose and before
installing the O-ring and purge screw.
(16) Remove hose (using quick disconnect), then remove purge adapter from the purge port.
(17) Inspect O-ring for signs of damage. Replace, if required. Lubricate O-ring with lubricant
and install with the purge screw into the purge port of the goggles.
Perform low light and high light resolution tests (para 3-9).
(2)
3-33/34 blank
TM 11-5855-262-23&P-2
APPENDIX A
REFERENCES
__________________________________________________________________________________
A-1 SCOPE
This appendix lists all the forms, field manuals, technical manuals, and miscellaneous publications
applicable to this manual.
A-2 FORMS
Hazardous Waste Profile Sheet .............................................................................DRMS 1930
Inspection and Maintenance Record......................................................................DA 2404
Maintenance Request............................................................................................DA 2407
Product Quality Deficiency Report .........................................................................SF 368
Recommended Changes to Equipment Technical Publications .............................DA 2028-2
Recommended Changes to Technical Publications ...............................................NAVMC 10772
Recommended Changes to Publications and Blank Forms....................................DA 2028
Report of Discrepancy ...........................................................................................SF 364
Requisition and Invoice/Shipping Document ..........................................................DD 1149
TM 11-5855-262-23&P-2
A-6 MARINE CORPS USE
Equipment Record Procedures.............................................................................. TM 4700-15/1
Marine Corps Publication Distribution System ....................................................... MCPDS
Recommended Changes to Publications/Logistics-Maintenance Data Coding ...... NAVMC 10772
Transportation and Travel Record of
Transportation Discrepancies ......................................................................... MCO P4610.19
Quality Deficiency Report ...................................................................................... MCO 4855.10
A-2
TM 11-5855-262-23&P-2
APPENDIX B
MAINTENANCE ALLOCATION CHART (MAC) (ARMY ONLY)
Section I. Introduction.
B-1 THE ARMY MAINTENANCE SYSTEM, MAC
a. This introduction (Section I) provides a general explanation of all maintenance and repair
functions authorized at various maintenance levels under the standard Army Maintenance System
concept.
b. The MAC in Section II designates overall authority and responsibility for the performance of
maintenance functions on the identified end item or component. The application of the maintenance
functions to the end item or component will be consistent with the capacities and capabilities of the
designated maintenance levels, which are shown on the MAC in column (4) as:
Unit includes two subcolumns, C (operator/crew) and O (unit) maintenance.
Direct Support includes an F subcolumn.
General Support includes an H subcolumn.
Depot includes a D subcolumn.
c. Section III lists the tools and test equipment (both special tools and common tool sets) required
for each maintenance function as referenced from Section II.
d. Section IV contains supplemental instructions and explanatory notes for a particular
maintenance function.
B-1
TM 11-5855-262-23&P-2
g. Remove/Install. To remove and install the same item when required to perform service or other
maintenance functions. Install may be the act of emplacing, seating or fixing into position a spare,
repair part, or module (component or assembly) in a manner to allow the proper functioning of the
equipment or system.
h. Replace. To remove an unserviceable item and install a serviceable counterpart in its place.
Replace is authorized by the MAC and assigned maintenance level is shown as the 3d position of the
SMR code.
i. Repair. The application of maintenance services1 including fault location/ troubleshooting2,
removal/installation, and disassembly/assembly3 procedures, and maintenance actions4 to identify
troubles and restore serviceability to an item by correcting specific damage, fault, malfunction, or failure
in a part, subassembly, module (component or assembly), end item, or system.
j. Overhaul. That maintenance effort (service/action) prescribed to restore an item to a
completely serviceable/operational condition as required by maintenance standards in appropriate
technical publications (i.e. DMWR). Overhaul is normally the highest degree of maintenance performed
by the Army. Overhaul does not normally return an item to like new conditions.
k. Rebuild. Consists of those services/actions necessary for the restoration of unserviceable
equipment to a like-new condition in accordance with original manufacturing standards. Rebuild is the
highest degree of material maintenance applied to Army equipment. The rebuild operation includes the
act of returning to zero those age measurements (hours, miles, etc.) considered in classifying Army
equipment/components.
TM 11-5855-262-23&P-2
This work-time figure represents the active time required to perform that maintenance function at the
indicated level of maintenance. If the number or complexity of the tasks within the listed maintenance
function vary at different maintenance levels, appropriate work-time figures will be shown for each level.
The work-time figure represents the average time required to restore an item (assembly, subassembly,
and module, end item, or system) to a serviceable condition under typical field operating conditions.
This time includes preparation time (including any necessary disassembly/assembly time),
troubleshooting/fault location time, and quality assurance time in addition to the time required to
perform the specific tasks identified for the maintenance functions authorized in the MAC. The symbol
designations for the various maintenance levels are as follows:
C
O
F
L
H
D
e. Column 5, Tools and Equipment. Column 5 specifies, by code, those common tool sets (not
individual tools), common TMDE, and special tools, special TMDE, and special support equipment
required to perform the designated function.
f. Column 6, Remarks. When applicable, this column contains a letter code, in alphabetical order,
that is keyed to the remarks contained in Section IV.
5This maintenance level is not included in Section II, column 4, of the MAC. Functions to this level
of maintenance are identified by a work-time figure in the H column of Section II, column 4, and an
associated reference code is used in the Remarks column (6). This code is keyed to section IV,
Remarks, and the SRA complete repair application is explained there.
B-3
TM 11-5855-262-23&P-2
Section II. Maintenance Allocation Chart for AN/PVS-7B and AN/PVS-7D.
(1)
(2)
(3)
(4)
MAINTENANCE LEVEL
00
01
02
B-4
FUNCTION
AN/PVS-7B, AN/PVS-7D
GOGGLE ASSEMBLY
HEADSET ASSEMBLY
INSPECT
SERVICE
REPAIR
0.1
0.1
0.1
INSPECT
TEST
REPAIR
TEST
REPAIR
0.2
0.3
0.2
INSPECT
REPLACE
REPAIR
0.1
0.1
0.1
(5)
(6)
TOOLS
REMARKS
AND
EQUIP
CODE
REF CODE
A
B
0.4
0.9
1
11
1,2,10
3-9,12
C
D
C
C, E, F, G
TM 11-5855-262-23&P-2
Section III. Tools and Test Equipment Requirements for AN/PVS-7B and AN/PVS-7D.
TOOL OR
TEST
EQUIPMENT
REF CODE
MAINTENANCE
LEVEL
O, F
NATIONAL
STOCK NUMBER
TOOL NUMBER
6625-01-323-9584
80063-A3139775
6625-01-301-6894
80063-A3134100
Multimeter
6625-01-139-2512
PSM-45 or equivalent
5180-00-610-8177
80058-TK105G
OR
Tool Kit, Electronic-Optical Repair
(Marine Corps)
5180-01-382-1335
TAMCN:E22082E
NOMENCLATURE
Device, Purge
5855-01-246-6815
54490-5007665
6830-01-265-4068
81348-BB-N-411
OR
Nitrogen, Technical 81 cubic feet
7
5855-01-151-4211
80063-SM-C-657451
5120-00-624-8065
39428-555A3
4931-00-065-1110
19200-SC493195CLJ54
10
6240-01-275-8080
80063-A3085081
11
5180-00-064-5178
80058-TK101GISSUE6
12
5120-01-335-1264
55719-OEX36B
13
Tape Measuring
5210-00-293-3505
81348-GGG-T-106
B-5
TM 11-5855-262-23&P-2
REMARKS
CODE
B-6
REMARKS
Dark adaptation takes at least 10 minutes (longer if exposed to bright sunlight before
inspection).
Repair by replacing the headmount, helmet mount, carrying case, carrying case
strap, tethering cord, compass, sacrificial window, IR spot/flood lens, LIF, demist
shields, neck cord, eyecups, objective lens cap, battery cap, or power switch knob.
Repair by replacing the image intensifier, rear cover, wired housing, objective lens,
or collimator.
TM 11-5855-262-23&P-2
APPENDIX C
REPAIR PARTS AND SPECIAL TOOLS LIST
Section I. Introduction.
C-1 SCOPE
This Repair Parts and Special Tools List (RPSTL) authorizes spares and repair parts, special tools,
special test, measurement, and diagnostic equipment (TMDE), and other special support equipment
required for performance of direct support maintenance and unit support maintenance of the NVG. It
authorizes the requisitioning, issue, and disposition of spares, repair parts, and special tools as
indicated by the source, maintenance, and recoverability (SMR) codes.
C-2 GENERAL
In addition to Section I, Introduction, this Repair Parts and Special Tools List is divided into the
following sections:
a. Section II. Repair Parts List. A list of spares and repair parts authorized by this RPSTL for
use in the performance of maintenance. The list also includes parts that must be removed for replacing
authorized parts. The parts lists are composed of functional groups in ascending alphanumeric
sequence, with the parts in each group listed in ascending figure and item number sequence. Items
listed are shown on the associated illustration(s)/figure(s).
b. Section III. Special Tools List. A list of special tools authorized by this RPSTL (as indicated
by Basis of Issue (BOI) information in DESCRIPTION AND USABLE ON CODE column) for the
performance of maintenance.
c. Section IV. National Stock Number and Part Number Index. A list, in National Item
Identification Number (NIIN) sequence, of all national stock numbered items appearing in the list,
followed by a list in alphanumerical sequence, of all part numbers appearing in the lists. National stock
numbers and part numbers are cross-referenced to each illustration figure and item number
appearance.
C-1
TM 11-5855-262-23&P-2
Table C-1. Application of Joint Services SMR Codes.
SOURCE
ST
ND
1 POSITION
PROCURE
MANUFACTURE
ASSEMBLE
A
B
2 POSITION
REPLENISH
INSURANCE
CURE DATED
D
E
F
F
INITIAL
END ITEM
GSE/STOCKED
GSE/NOT STOCKED
ORG/IMA
DEPOT
BOTH KITS
O
F
H
G
D
A
ORG
AFLOAT
ASHORE
BOTH
DEPOT
REQUEST NHA
B
X
MAINTENANCE
MISC
C
REPLACE OR USE AT
IMA LEVEL
REPLACE OR USE AT
SPECIALIZED IMA
NO REPAIR
(CONSUMABLE)
RECONDITION BY
ADJUSTMENT,
CALIBRATION,
LUBRICATION, PLATING,
ETC.
REPAIR AT
ORGANIZATIONAL LEVEL
REPLACE OR USE AT
DEPOT
G
L
REPAIR AT SPECIALIZED
IMA
REPAIR AT DEPOT OR
COMMERCIAL
SERVICE OPTION
TH
N
M
T
1
2
3
4
5
6
E
J
C-2
H
D
REPLACE OR USE AT
ORG LEVEL
H
F
TH
TH
4 POSITION
RECOVERABILITY
Z
REPAIR
3 POSITION
RD
OBTAIN FROM
SALVAGE OR ONE
TIME BUY
DIAGRAMS,
SCHEMATICS, INSTALL
DWGS
5 POSITION
NONREPAIRABLE CONDEMN AT INDICATED IN
POSITION 3
SPECIAL HANDLING FOR DISPOSAL
USE
6 POSITION
CONSUMABLE GAM ITEM NOT CENTRALLY PROCURED
OR STOCK NUMBERED
TH
FLR ITEM WITH UNIT COST OVER $5,000. CHANGE 5
POSITION TO D
TRAINING DEVICE ITEM SOURCE CODED PD
NORMALLY PROCURED COMMERCIAL, BUT ORGANIC
CAPABILITY EXISTS FOR EMERGENCY STOP GAP
REQUIREMENTS
(APPLY TO ENGINES)
RD
(APPLIES TO 3 POSITION)
DESIGNATED LOWEST DEGREE OF IMA REPAIR
AUTHORITY
(APPLY TO ENGINES)
RD
(APPLIES TO 3 POSITION)
SAME AS 1-2-3 EXCEPT ITEM IS FLR COSTING MORE
THAN $5,000
END-TO-END TEST BY IMA REQUIRED PRIOR TO BOM
TH
FLR OR CONSUMABLE CHANGE 5 POSITION TO D
UNDER PICA/SICA PROGRAM (APPROVAL REQUIRED)
TM 11-5855-262-23&P-2
c. NATIONAL STOCK NUMBER (Column(3)). This column lists the NSN for the associated part
number and manufacturer identified in the PART NUMBER and CAGEC columns to the right.
d. CAGEC (Column (4)). The Commercial and Government Entity Code (CAGEC) is a 5-digit code
which is used to identify the manufacturer, distributor, or government agency/activity, that
supplies the item.
e. PART NUMBER (Column (5)). Indicates the primary number used by the manufacturer
(individual, company, firm, corporation, or government activity), which controls the design and
characteristics of the item by means of its engineering drawings, specifications, standards, and
inspection requirements to identify an item or range of items.
NOTE
When you use an NSN to requisition an item, the item you receive may
have a different part number from the number listed.
f. DESCRIPTION AND USABLE ON CODE (UOC) (Column (6)).
following information:
(1) The federal item name, and when required, a minimum description to identify the item.
(2) The physical security classification of the item is indicated by the appropriate parenthetical
entry, e. g., Phy Sec C1 (C) -Confidential, Phy Sec C1 (S) -Secret, Phy Sec C1 (T) - Top
Secret).
(3) Items that are included in kits and sets are listed below the name of the kit or set.
(4) Spare/repair parts that make up an assembled item are listed immediately following the
assembled item line entry.
(5
Part numbers for bulk materials are referenced in the column in the line entry for the item to
be manufactured/fabricated.
(6) When the item is not used with all serial numbers of the same model, the effective serial
numbers are shown on the last line of the description (before UOC).
(7) The UOC, when applicable (para C-5, Special Information).
(8) In the Special Tools List Section, the basis of issue (BOI) appears as the last line(s) in the
entry for each special tool, special TMDE, and other special support equipment. When
density of equipment supported exceeds density spread indicated in the basis of issue, the
total authorization is increased proportionately.
(9) The statement "END OF FIGURE" appears just below the last item description in Column 6
for a given figure in both Section II and Section III.
g. QTY (Column (7)). The QTY (quantity per figure column) indicates the quantity of the item used
in the breakout shown on the illustration figure, which is prepared for a functional group, subfunctional group, or assembly. A "V" appearing in this column instead of a quantity indicates that
the quantity is variable and the quantity may change from application to application.
C-3
TM 11-5855-262-23&P-2
C-4. EXPLANATION OF COLUMNS
a. NATIONAL STOCK NUMBER (NSN) INDEX.
(1) STOCK NUMBER column. This column lists the NSN by NIIN sequence. The NIIN consists
of the last nine digits of the NSN. An example is shown below.
NSN____ _
5855-01-432-0524
NIIN
When using this column to locate an item, ignore the first four digits of the NSN. However, the
complete NSN should be used when ordering items by stock number.
(2) FIG. column. This column lists the number of the figure where the item is identified/located.
The figures are in numerical order in Section II and Section III.
(3) ITEM column. The item number identifies the item associated with the figure listed in the
adjacent FIG. column. This item is also identified by the NSN listed on the same line.
(4) CAGEC column. The Commercial and Government Entity (CAGE) code is a 5-digit numeric
code used to identify the manufacturer, distributor, or government agency, etc., that supplies
the item.
(5) PART NUMBER column. Indicates the primary number used by the manufacturer (individual,
firm, corporation, or government activity), which controls the design and characteristics of the
item by means of its engineering drawings, specifications, standards, and inspection
requirements to identify an item or range of items.
b. PART NUMBER INDEX. Part numbers in this index are listed by part number in ascending
alphanumeric sequence (vertical arrangement of letter and number combination which places
the first letter or digit of each group in order A through Z, followed by the numbers 0 through 9
and each following letter or digit in like order).
(1) CAGEC column. The Commercial and Government entity (CAGE) code is a 5-digit numeric
code used to identify the manufacturer, distributor, or government agency, etc., that supplies
the item.
(2) PART NUMBER column. Indicates the primary number used by the manufacturer (individual,
firm, corporation, or government activity), which controls the design and characteristics of the
item by means of its engineering drawings, specifications, standards, and inspection
requirements to identify an item or range of items.
(3) STOCK NUMBER column. This column lists the NSN for the associated part number and
manufacturer identified in the PART NUMBER and CAGEC columns to the left.
(4) FIG. column. This column lists the number of the figure where the item is identified/located in
Sections II and III.
(5) ITEM column. The item number is that number assigned to the item as it appears in the
figure referenced in the adjacent figure number column.
C-4
TM 11-5855-262-23&P-2
c. FIGURE NUMBER INDEX.
(1) FIG. column. This column lists the number of the figure where the item is identified/located.
The figures are in numerical order in Section II and Section III.
(2) ITEM column. The item number identifies the item associated with the figure listed in the
adjacent FIG. column. This item is also identified by the NSN listed on the same line.
(3) STOCK NUMBER column. This column lists the NSN by NIIN sequence. The NIIN consists
of the last nine digits of the NSN. An example is shown below.
NSN____ _
5855-01-432-0524
NIIN
(4) CAGEC column. The Commercial and Government Entity (CAGE) code is a 5-digit numeric
code used to identify the manufacturer, distributor, or government agency, etc., that supplies
the item.
(5) PART NUMBER column. Indicates the primary number used by the manufacturer (individual,
firm, corporation, or government activity), which controls the design and characteristics of the
item by means of its engineering drawings, specifications, standards, and inspection
requirements to identify an item or range of items.
USED ON
HKG
LDF
AN/PVS-7B
AN/PVS-7D
TM 11-5855-262-23&P-2
C-6. HOW TO LOCATE REPAIR PARTS Continued.
(4) Fourth. Refer to the Repair Parts List for the figure to find the part number for the item
number noted on the figure.
(5) Fifth. Refer to the Part Number Index to find the NSN, if assigned.
b. When National Stock Number or Part Number is Known:
(1) First. Using the Index of National Stock Numbers and Part Numbers, find the pertinent
National Stock Number or Part Number. The NSN index is in National Item Identification
Number (NIIN) sequence (C-4. a (3)). The part numbers in the Part Number index are listed
in ascending alphanumeric sequence (C-4. b). Both indexes cross-reference you to the
illustration figure and item number of the item you are looking for.
(2) Second. After finding the figure and item number, verify that the item is the one you're
looking for, then locate the item number in the repair parts list for the figure.
C-7. ABBREVIATIONS.
NOT APPLICABLE
C-6/C-7 blank
TM 11-5855-262-23&P-2
Section II. Repair Parts List.
C-8
TM 11-5855-262-23&P-2
Section II. Repair Parts List - Continued
(1)
(2)
(3)
(4)
(5)
(6)
(7)
ITEM
NO.
SMR
CODE
NATIONAL
STOCK NUMBER
CAGEC
PART
NUMBER
DESCRIPTION AND
USABLE ON CODE (UOC)
QTY
GROUP 00
PAOOO
5855-01-246-8266
80063
A3144268
HEADSET ASSEMBLY
(FIGURE C-3 FOR PARTS
BREAKDOWN)
XBOZZ
5855-01-246-6805
80063
A3144257
CASE, SHIPPING
XBOZZ
80063
A3264350
CASE, SHIPPING
PAOZZ
5340-01-250-2431
80063
A3144267
STRAPPING
PAOZZ
5855-01-398-4284
80063
A3187392
PAOZZ
5340-01-451-7737
80063
A3260933
CLIP, RETAINING
PAOZZ
5855-01-457-2953
80063
A3256368
MOUNT VIEWER
PAOZZ
5855-01-246-8272
80063
A3144263
XAFFF
80063
A3144261-1
XAFFF
80063
A3144261-2
PAOZZ
5855-01-382-5169
80063
A3187441
10
PAOZZ
5855-01-246-8271
80063
A3144264
WINDOW, SACRIFICIAL
11
PAOZZ
5340-01-397-6608
80063
A3144318
12
PAOZZ
5855-01-379-1410
54490
5009737
13
PAOZZ
5855-01-381-6052
80063
A3187430
COMPASS ASSEMBLY
END OF FIGURE
C-9
TM 11-5855-262-23&P-2
Section II. Repair Parts List Continued
C-10
TM 11-5855-262-23&P-2
Section II. Repair Parts List - Continued
(1)
(2)
(3)
(4)
(5)
(6)
(7)
ITEM
NO.
SMR
CODE
NATIONAL
STOCK NUMBER
CAGEC
PART
NUMBER
DESCRIPTION AND
USABLE ON CODE (UOC)
QTY
GROUP 01
GOGGLE ASSEMBLY
FIGURE C-2
PAFZZ
5855-01-246-6807
80063
A3144305
PAFZZ
5330-01-049-7374
96906
MS28775-032
PACKING, PREFORMED
PAFZA
5855-01-422-4720
80063
A3256388
IMAGE INTENSIFIER, N
PAOZZ
5855-01-246-8273
80063
A3144422
EYECUP
PAFZZ
5310-00-043-4708
80063
A3144314
WASHER, FLAT
PAFZZ
5305-00-224-0783
96906
MS51957-4B
SCREW, MACHINE
PAFZZ
5330-01-356-7219
80063
A3144316
PACKING, PREFORMED
PAFZZ
5305-01-266-9341
80063
A3144315
SCREW, MACHINE
PAFZZ
5855-01-246-6810
80063
A3144310
10
PAFZZ
5330-01-098-1232
96906
MS28775-044
PACKING, PREFORMED
11
PAOZZ
4020-01-446-8097
80063
A3144306
CORD, FIBROUS
12
PAOZZ
5930-01-246-8264
80063
A3144404
13
PAFZZ
5855-01-381-6048
80063
A3207330
14
PAFZZ
5310-00-433-3599
96906
MS15795-802B
WASHER, FLAT
15
PAFZZ
5855-01-246-6808
80063
A3172531
COLLIMATOR, INFRARED
16
PAOZZ
5330-00-729-4992
96906
MS28775-027
PACKING, PREFORMED
17
PAOZZ
5855-01-246-8265
80063
A3144394
18
PAOZZ
5935-01-448-6355
80063
A3260939
RETAINER, ELECTRICAL
10
END OF FIGURE
C-11
TM 11-5855-262-23&P-2
Section II. Repair Parts List - Continued
TM 11-5855-262-23&P-2
(2)
(3)
(4)
(5)
(6)
(7)
ITEM
NO.
SMR
CODE
NATIONAL
STOCK NUMBER
CAGEC
PART
NUMBER
DESCRIPTION AND
USABLE ON CODE (UOC)
QTY
GROUP 02
HEADSET ASSEMBLY
FIGURE C-3
PAOZZ
5340-01-306-9354
80063
A3144292
STRAPPING
PAOZZ
5855-01-297-7846
80063
A3144290
PAOZZ
5340-01-360-1724
80063
A3144293
STRAP, WEBBING
PAOZZ
5855-01-297-7847
80063
A3144436
PAOZZ
5855-01-355-8600
80063
A3144435
PAOZZ
5855-01-355-8599
80063
A3144280
PAOZZ
5855-01-283-2870
80063
A3144286
CHINSTRAP, HELMET
END OF FIGURE
C-13
TM 11-5855-262-23&P-2
Section III. Special Tools List.
TM 11-5855-262-23&P-2
Section III. Special Tools List - Continued
(1)
ITEM
NO.
(2)
SMR
CODE
(3)
(4)
NATIONAL
CAGE
STOCK NUMBER CODE
(5)
(6)
PART
NUMBER
DESCRIPTION AND
USABLE ON CODE (UOC)
GROUP 10
SPECIAL TOOLS
(7)
QTY
FIGURE C-4
1
PAFZZ
5120-00-345-1406 19200
7597658
WRENCH, SPANNER
BOI: 1 PER UNIT
PAFZZ
5855-01-151-4211 80063
PAFZZ
6240-01-275-8080 80063
A3085081
PEFFF
5855-01-246-6815 54490
5007665
DEVICE, PURGE
PAFZZ
5855-01-250-2359 54490
5007678
PAFZZ
5855-01-250-2361 54490
5007693
CASE, CARRYING
XAFZZ
5855-01-250-2358 54490
5007679
END OF FIGURE
C-15
TM 11-5855-262-23&P-2
Section IV.
CROSS-REFERENCE INDEXES
NATIONAL STOCK NUMBER INDEX
STOCK NUMBER
FIG
ITEM CAGEC
PART NUMBER
5310-00-043-4708
5305-00-224-0783
5120-00-345-1406
5310-00-433-3599
5330-00-729-4992
5330-01-049-7374
5330-01-098-1232
5855-01-151-4211
5855-01-246-6805
5855-01-246-6807
5855-01-246-6808
5855-01-246-6810
5855-01-246-6815
5930-01-246-8264
5855-01-246-8265
5855-01-246-8266
5855-01-246-8271
5855-01-246-8272
5855-01-246-8273
5855-01-250-2358
5855-01-250-2359
5855-01-250-2361
5340-01-250-2431
5305-01-266-9341
6240-01-275-8080
5855-01-283-2870
5855-01-297-7846
5855-01-297-7847
5340-01-306-9354
5855-01-355-8599
5855-01-355-8600
5330-01-356-7219
5340-01-360-1724
5855-01-379-1410
5855-01-381-6048
5855-01-381-6052
5855-01-382-5169
5340-01-397-6608
5855-01-398-4284
5855-01-422-4720
5855-01-457-2953
4020-01-446-8097
5935-01-448-6355
C-2
C-2
C-4
C-2
C-2
C-2
C-2
C-4
C-1
C-2
C-2
C-2
C-4
C-2
C-2
C-1
C-1
C-1
C-2
C-4
C-4
C-4
C-1
C-2
C-4
C-3
C-3
C-3
C-3
C-3
C-3
C-2
C-3
C-1
C-2
C-1
C-1
C-1
C-1
C-2
C-1
C-2
C-2
5
6
1
14
16
2
10
2
2
1
15
9
4
12
17
1
10
7
4
7
5
6
3
8
3
7
2
4
1
6
5
7
3
12
13
13
9
11
4
3
6
11
18
A3144314
MS51957-4B
7597658
MS15795-802B
MS28775-027
MS28775-032
MS28775-044
SM-C-657451
A3144257
A3144305
A3172531
A3144310
5007665
A3144404
A3144394
A3144268
A3144264
A3144263
A3144422
5007679
5007678
5007693
A3144267
A3144315
A3085081
A3144286
A3144290
A3144436
A3144292
A3144280
A3144435
A3144316
A3144293
5009737
A3207330
A3187430
A3187441
A3144318
A3187392
A3256388
A3256368
A3144306
A3260939
C-16
80063
96906
19200
96906
96906
96906
96906
80063
80063
80063
80063
80063
54490
80063
80063
80063
80063
80063
80063
54490
54490
54490
80063
80063
80063
80063
80063
80063
80063
80063
80063
80063
80063
54490
80063
80063
80063
80063
80063
80063
80063
80063
80063
TM 11-5855-262-23&P-2
Section IV. - Continued
CROSS-REFERENCE INDEXES
NATIONAL STOCK NUMBER INDEX - Continued
STOCK NUMBER
FIG
ITEM CAGEC
PART NUMBER
5340-01-451-7737
C-1
C-1
C-1
C-1
5
2
8
8
A3260933
A3264350
A3144261-1
A3144261-2
80063
80063
80063
80063
C-17
TM 11-5855-262-23&P-2
Section IV. - Continued
CROSS-REFERENCE INDEXES
PART NUMBER INDEX
C-18
PART NUMBER
CAGEC
STOCK NUMBER
FIG
ITEM
5009737
5007678
5007679
5007693
7597658
A3085081
A3144257
A3144261-1
A3144261-2
A3144263
A3144264
A3144267
A3144268
A3144280
A3144286
A3144290
A3144292
A3144293
A3144305
A3144306
A3144310
A3144314
A3144315
A3144316
A3144318
A3144394
A3144404
A3144422
A3144435
A3144436
A3172531
A3187392
A3187430
A3187441
A3207330
A3256388
A3256368
A3260933
A3260939
A3264350
5007665
MS15795-802B
MS28775-027
54490
54490
54490
54490
19200
80063
80063
80063
80063
80063
80063
80063
80063
80063
80063
80063
80063
80063
80063
80063
80063
80063
80063
80063
80063
80063
80063
80063
80063
80063
80063
80063
80063
80063
80063
80063
80063
80063
80063
80063
54490
96906
96906
5855-01-379-1410
5855-01-250-2359
5855-01-250-2358
5855-01-250-2361
5120-00-345-1406
6240-01-275-8080
5855-01-246-6805
C-1
C-4
C-4
C-4
C-4
C-4
C-1
C-1
C-1
C-1
C-1
C-1
C-1
C-3
C-3
C-3
C-3
C-3
C-2
C-2
C-2
C-2
C-2
C-2
C-1
C-2
C-2
C-2
C-3
C-3
C-2
C-1
C-1
C-1
C-2
C-2
C-1
C-1
C-2
C-1
C-4
C-2
C-2
12
5
7
6
1
3
2
8
8
7
10
3
1
6
7
2
1
3
1
11
9
5
8
7
11
17
12
4
5
4
15
4
13
9
13
3
6
5
18
2
4
14
16
5855-01-246-8272
5855-01-246-8271
5340-01-250-2431
5855-01-246-8266
5855-01-355-8599
5855-01-283-2870
5855-01-297-7846
5340-01-306-9354
5340-01-360-1724
5855-01-246-6807
4020-01-446-8097
5855-01-246-6810
5310-00-043-4708
5305-01-266-9341
5330-01-356-7219
5340-01-397-6608
5855-01-246-8265
5930-01-246-8264
5855-01-246-8273
5855-01-355-8600
5855-01-297-7847
5855-01-246-6808
5855-01-398-4284
5855-01-381-6052
5855-01-382-5169
5855-01-381-6048
5855-01-422-4720
5855-01-457-2953
5340-01-451-7737
5935-01-448-6355
5855-01-246-6815
5310-00-433-3599
5330-00-729-4992
TM 11-5855-262-23&P-2
Section IV. - Continued
CROSS-REFERENCE INDEXES
PART NUMBER INDEX - Continued
PART NUMBER
CAGEC
STOCK NUMBER
FIG
ITEM
MS28775-032
MS28775-044
MS51957-4B
SM-C-657451
96906
96906
96906
80063
5330-01-049-7374
5330-01-098-1232
5305-00-224-0783
5855-01-151-4211
C-2
C-2
C-2
C-4
2
10
6
2
C-19
TM 11-5855-262-23&P-2
Section IV-Continued
CROSS-REFERENCE INDEXES
FIGURE AND ITEM NUMBER INDEX
FIG
ITEM
STOCK NUMBER
CAGEC
PART NUMBER
C-1
C-1
C-1
C-1
C-1
C-1
C-1
C-1
C-1
C-1
C-1
C-1
C-1
C-1
C-1
C-2
C-2
C-2
C-2
C-2
C-2
C-2
C-2
C-2
C-2
C-2
C-2
C-2
C-2
C-2
C-2
C-2
C-2
C-3
C-3
C-3
C-3
C-3
C-3
C-3
C-4
C-4
C-4
C-4
1
2
2
3
4
5
6
7
8
8
9
10
11
12
13
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
1
2
3
4
5
6
7
1
2
3
4
5855-01-246-8266
5855-01-246-6805
80063
80063
80063
80063
80063
80063
80063
80063
80063
80063
80063
80063
80063
54490
80063
80063
96906
80063
80063
80063
96906
80063
80063
80063
96906
80063
80063
80063
96906
80063
96906
80063
80063
80063
80063
80063
80063
80063
80063
80063
19200
80063
80063
54490
A3144268
A3144257
A3264350
A3144267
A3187392
A3260933
A3256368
A3144263
A3144261-1
A3144261-2
A3187441
A3144264
A3144318
5009737
A3187430
A3144305
MS28775-032
A3256388
A3144422
A3144314
MS51957-4B
A3144316
A3144315
A3144310
MS28775-044
A3144306
A3144404
A3207330
MS15795-802B
A3172531
MS28775-027
A3144394
A3260939
A3144292
A3144290
A3144293
A3144436
A3144435
A3144280
A3144286
7597658
SM-C-657451
A3085081
5007665
C-20
5340-01-250-2431
5855-01-398-4284
5340-01-451-7737
5855-01-457-2953
5855-01-246-8272
5855-01-382-5169
5855-01-246-8271
5340-01-397-6608
5855-01-379-1410
5855-01-381-6052
5855-01-246-6807
5330-01-049-7374
5855-01-422-4720
5855-01-246-8273
5310-00-043-4708
5305-00-224-0783
5330-01-356-7219
5305-01-266-9341
5855-01-246-6810
5330-01-098-1232
4020-01-446-8097
5930-01-246-8264
5855-01-381-6048
5310-00-433-3599
5855-01-246-6808
5330-00-729-4992
5855-01-246-8265
5935-01-448-6355
5340-01-306-9354
5855-01-297-7846
5340-01-360-1724
5855-01-297-7847
5855-01-355-8600
5855-01-355-8599
5855-01-283-2870
5120-00-345-1406
5855-01-151-4211
6240-01-275-8080
5855-01-246-6815
TM 11-5855-262-23&P-2
Section IV. - Continued
CROSS-REFERENCE INDEXES
FIGURE AND ITEM NUMBER INDEX - Continued
FIG
ITEM
STOCK NUMBER
CAGEC
PART NUMBER
C-4
C-4
C-4
5
6
7
5855-01-250-2359
5855-01-250-2361
5855-01-250-2358
54490
54490
54490
5007678
5007693
5007679
C-21/22 blank
TM 11-5855-262-23&P-2
APPENDIX D
EXPENDABLE AND DURABLE ITEMS LIST
Section I. Introduction.
D-1 SCOPE
This appendix lists expendable and durable items that you will need to operate and maintain the Night
Vision Goggles (NVG), AN/PVS-7B and AN/PVS-7D. This listing is for information only and is not
authority to requisition the listed items. These items are authorized to you by CTA 50-970,
Expendable/Durable Items (Except Medical, Class V Repair Parts, and Heraldic Items) or CTA 8-100,
Army Medical Department Expendable/Durable Items.
Operator/Crew
Unit Maintenance
Direct Support Maintenance
General Support Maintenance
Depot
d. Description (Column 4). Indicates the federal item name and, if required, a description to
identify the item. The last line for each item indicates the Commercial and Government Entity Code
(CAGEC) code in parenthesis followed by the part number.
e. Unit of Measure (U/M)/Unit of Issue (U/I) (Column 5). This measure is expressed by a twocharacter alphabetical abbreviation (e.g., DA, IN, PR). If the unit of measure differs from the unit of
issue as shown in the Army Master Data File (AMDF), requisition the lowest unit of issue that will satisfy
your requirements.
D-1
TM 11-5855-262-23&P-2
Section II. Expendable and Durable Items List.
(1)
(2)
ITEM
NUMBER LEVEL
(3)
(4)
(5)
NATIONAL STOCK
NUMBER
DESCRIPTION, CAGEC
AND PART NUMBER
U/M
U/I
OZ
6810-00-753-4993
9150-01-132-8871
7930-00-926-5280
BX
6830-01-265-4068
NITROGEN, TECHNICAL
(81348) BB-N-411
CY
6830-00-973-7283
NITROGEN, TECHNICAL
(81348) BB-N-411
EA
Or
3439-00-552-9309
DISPENSER, ALCOHOL
(33092) 3316
EA
7920-00-823-9773
TOWEL, SHOP
(81348) UU-T-595
MX
6640-01-459-4239
PAPER, LENS
(81348) A-A-50177
TYPE I, CLASS 5
PG
8030-01-390-7555
SEALING COMPOUND
(05972) 42540
BT
6830-00-602-2357
OZ
10
6515-00-303-8250
PG
D-2
TM 11-5855-262-23&P-2
APPENDIX E
ILLUSTRATED LIST OF MANUFACTURED ITEMS
__________________________________________________________________________________
Section I. Introduction.
a. This appendix includes complete instructions for making items authorized to be manufactured
or fabricated at the unit or direct support (DS) maintenance level. The black spot test stand is
authorized for Unit/DS.
b. A part number index in alphanumeric order is provided for cross-referencing the part number of
the item to be manufactured to the figure which covers fabrication criteria.
c. All bulk materials needed for manufacture of an item are listed by part number or specification
number in a tabular list on the illustration.
5855-01-305-8524
EA
E-1
N/A
EA
E-1
N/A
EA
E-1
N/A
EA
E-1
N/A
EA
E-1
N/A
EA
E-1
N/A
EA
E-1
N/A
E-1
TM 11-5855-262-23&P-2
Section III. Manufactured Items Illustrations.
E-2
TM 11-5855-262-23&P-2
GLOSSARY
__________________________________________________________________________________
Section I. Abbreviations.
AMDF
BOI
CAGEC
cm
CPC
CTA
DA
DMWR
DRMO
DS
EIC
EIR
FM
IAW
IR
lbs
LED
LIF
MAC
MCPDS
mm
MTOE
MWO
N/A
NATO
NIIN
NSN
NVG
Pam
PASGT
PMCS
POC
PQDR
psi
Qty
RA
RGA
RPSTL
Rqd
SAMS
SF
SMR
SRA
TBD
TM
TMDE
TO
U/I
ULLS
U/M
UOC
Vdc
Technical Order
Unit of Issue
Unit Level Logistics System
Unit of Measure
Usable on Code
Volts, direct current
Glossary-1
TM 11-5855-262-23&P-2
TM 11-5855-262-23&P-2
FLASHING. This is a defect in which the image appears to flicker. This occurs in the image intensifier.
If there is more than one flicker, check for loose wires, loose cap, or weak batteries.
GAIN. This is the number of times a night vision device amplifies light input.
GOGGLE ASSEMBLY. The goggle assembly, hereafter referred to as goggle, is the viewing unit.
HEADMOUNT. The adjustable cushioned headmount secures the goggles to the operator's head for
night viewing, providing freehand support for use with a weapon, protective mask or other purposes.
IMAGE INTENSIFIER. An electro-optical device that detects and amplifies ambient light to produce a
visual image. It consists of a photocathode, microchannel plate, phosphor screen optics, and integral
power supply.
INFINITY FOCUS. Adjustment of the objective lens so that a distant object, such as a star or the point
light on a distant tower, forms the sharpest image.
INTERMITTENT OPERATION. This a defect in the image area of the NVG. See flashing.
IR SOURCE. This is an IR Light Emitting Diode (LED). When turned on, the IR Source provides
additional illumination to enhance existing light conditions. Used only for performing near by tasks.
LIGHT-INTERFERENCE FILTER (LIF). This is a light protection filter for the objective lens. Use of this
filter will result in a slight reduction in system gain.
MICROCHANNEL PLATE. A current-multiplying optical disk that intensifies the electron image
produced by the photo-cathode.
NOTE. Essential information of special importance, interest, or aid in job performance.
OBJECTIVE LENS. This consists of an objective lens cell and an objective focus ring. It attaches to
the front of the goggles and adjusts for variations in distance to the viewed area or object.
PHOTOCATHODE. The input optic of an image intensifier that absorbs light energy and in turn
releases electrical energy in the form of an electron image.
SACRIFICIAL WINDOW. A replaceable sacrificial window is supplied to protect the objective lens
during operation in adverse conditions.
SCINTILLATION. A faint, random, sparkling effect throughout the image area. Scintillation is a normal
characteristic of the image intensifier and should not be confused with emission points. Scintillation is
more pronounced under low light conditions. Also called video noise.
SHADING. The viewed image should be a full circle. If shading is present, you will not see a fully
circular image. Shading is indicative of a dying photocathode and is caused by a defective vacuum
seal of the image intensifier. Shading is very dark and you cannot see an image through it.
WARNING. Conditions, practices, or procedures that must be observed to avoid personal injury or loss
of life.
Glossary-3/4 blank
TM 11-5855-262-23&P-2
ALPHABETICAL INDEX
__________________________________________________________________________________
Subject ............................................................................................................................................ Para
A
Abbreviations............................................................................................................................ Glossary
Adjustment
Goggles .....................................................................................................................................1-13
Headmount ................................................................................................................................1-13
Ambient light......................................................................................................................................1-1
Ambient temperature limits ..............................................................................................................1-12
Appendices
A References ........................................................................................................................... A-1
B Maintenance Allocation Chart (MAC) Army only ................................................................... B-1
C Repair Parts and Special Tools List...................................................................................... C-1
D Expendable and Durable Items List....................................................................................... D-1
E Illustrated List of Manufactured Items.................................................................................... E-1
B
Battery
AA size ......................................................................................................................................1-12
Alkaline ......................................................................................................................................1-12
Cap ............................................................................................................................................2-12
Lithium .......................................................................................................................................1-12
Voltage ......................................................................................................................................1-15
Battery Cap and Battery Cap Retainer
Installation..................................................................................................................................2-12
Removal.....................................................................................................................................2-12
Black spots ..................................................................................................................3-11, Appendix E
Browpads ........................................................................................................................................1-10
Installation..................................................................................................................................2-13
Removal.....................................................................................................................................2-13
C
Carrying case ................................................................................................................1-10, 1-12, 2-11
Characteristics ..................................................................................................................................1-9
Chinstrap
Installation..................................................................................................................................2-15
Collimator assembly
Installation..................................................................................................................................3-15
Removal.....................................................................................................................................3-15
Common tools and equipment ....................................................................................................2-1, 3-1
Components
Installation..................................................................................................................................2-11
Removal.....................................................................................................................................2-11
Index-1
TM 11-5855-262-23&P-2
Subject ............................................................................................................................................ Para
C - Continued
Corrosion prevention and control....................................................................................................... 1-8
Cross reference list, nomenclature .................................................................................................... 1-5
Cross-Strap
Installation ................................................................................................................................. 2-16
Removal .................................................................................................................................... 2-16
D
Data
Electrical.................................................................................................................................... 1-12
Environmental ........................................................................................................................... 1-12
Equipment ................................................................................................................................. 1-12
Mechanical ....................................................................................................................... 1-12, 1-13
Optical ....................................................................................................................................... 1-12
Definition of Unusual Terms ............................................................................................... Glossary
Demist shields................................................................................................................................. 1-10
Destruction of electronic materiel to prevent enemy use ................................................................... 1-3
Diopter ................................................................................................................................... 1-12, 1-13
E
EIR.................................................................................................................................................... 1-6
Electrical function ............................................................................................................................ 1-15
Electronic circuit functions ............................................................................................................... 1-15
Environmental Data......................................................................................................................... 1-12
Equipment
Characteristics, capabilities and features..................................................................................... 1-9
Data........................................................................................................................................... 1-12
Description ................................................................................................................................ 1-10
Expendable and durable items list........................................................................................ Appendix D
Eye relief ......................................................................................................................................... 1-13
Eyecups .......................................................................................................................................... 2-11
Eyepiece
Focus ........................................................................................................................................ 1-12
Function .................................................................................................................................... 1-14
F
Field-of-view.................................................................................................................................... 1-12
Filter (See LIF)
Forms
DA 2404 ..................................................................................................................................... 1-7
DA 2407 ..................................................................................................................................... 1-7
DA Pam 25-30...................................................................................................................... 1-2, 2-5
DA Pam 738-750 ......................................................................................................................... 1-2
DD 1149 ..................................................................................................................................... 1-7
DRMS 1930.............................................................................................................................. 3-21
SF 364......................................................................................................................................... 2-5
SF 368......................................................................................................................................... 1-6
Index-2
TM 11-5855-262-23&P-2
Subject ............................................................................................................................................ Para
G
Goggles ...........................................................................................................................................1-10
H
Headmount ......................................................................................................................................2-11
Helmet mount ..................................................................................................................................2-11
High light
Cut-off........................................................................................................................................1-15
Resolution test ....................................................................................................................2-10, 3-9
I, J
Illustrated list of manufactured items..................................................................................... Appendix E
Image intensifier
Inspection criteria for proper image intensifier operation ..............................................................2-8
Installation..................................................................................................................................3-14
Configuration .............................................................................................................................1-11
Removal.....................................................................................................................................3-14
Shipping.....................................................................................................................................3-21
Infinity focus adjustment ..................................................................................................................3-13
Installation .........................................................................................................................................2-6
Interpupillary distance......................................................................................................................1-13
IR illumination ..................................................................................................................................1-15
IR Spot/Flood..........................................................................................................................1-10, 2-11
K
Knob
Installation..................................................................................................................................2-17
Power switch..............................................................................................................................2-17
Removal.....................................................................................................................................2-17
L
LED .................................................................................................................................................1-14
Lens cap..........................................................................................................................................2-11
LIF
.............................................................................................................................................1-10
Location and description of major components ................................................................................1-10
Low light resolution test ............................................................................................................2-10, 3-9
Lubrication requirements .................................................................................................................2-20
Index-3
TM 11-5855-262-23&P-2
Subject ............................................................................................................................................ Para
M
MTOE .............................................................................................................................................. 3-1
Magnet, Metal Helmet Mount
Installation ................................................................................................................................. 2-18
Removal .................................................................................................................................... 2-18
Maintenance
Allocation Chart (MAC) ............................................................................................ 2-2, Appendix B
Forms, records, and reports .................................................................................... 1-2, Appendix A
Major components, location and description.................................................................................... 1-10
Manufactured items, illustrated list of ................................................................................... Appendix E
Mechanical Data ............................................................................................................................. 1-12
Mechanical functions....................................................................................................................... 1-13
N
Neck cord........................................................................................................................................ 2-11
Neck pad
Installation ................................................................................................................................. 2-14
Removal .................................................................................................................................... 2-14
Nomenclature.................................................................................................................................... 1-5
O
Objective lens
Focus................................................................................................................................... 1-12
Infinity Focus Adjustment..................................................................................................... 3-13
Installation.............................................................................................................................. 3-12, 1-12
Operation .................................................................................................................................. 1-14
Removal .................................................................................................................................... 3-12
Operating temperature .................................................................................................................... 1-12
Operational checks.......................................................................................................................... 3-19
Operator adjustment limits............................................................................................................... 1-12
Optical functions.............................................................................................................................. 1-14
P, Q
Packing .................................................................................................................................. 2-21, 3-20
PMCS table ....................................................................................................................................... 2-7
Power
source ....................................................................................................................................... 1-15
switch ........................................................................................................................................ 1-15
Preparation for storage or shipment .................................................................................................. 1-4
Preparation for using TS-3895A/UV .................................................................................................. 3-8
Purging............................................................................................................................................ 3-18
Index-4
TM 11-5855-262-23&P-2
Subject ............................................................................................................................................ Para
R
Rear cover
Installation..................................................................................................................................3-17
Removal.....................................................................................................................................3-17
References ........................................................................................................................... Appendix A
Refinishing (See Repainting)
Repainting and refinishing requirements..........................................................................................2-19
Repair parts ................................................................................................................................2-3, 3-3
Reporting equipment improvement recommendation.........................................................................1-6
RPSTL................................................................................................................................. Appendix C
Resolution check using the TS-4348/UV test set .............................................................................2-10
Resolution testing using the TS-3895A/UV ........................................................................................3-9
S
Scope ........................................................................................................................................1-1, 3-6
Service upon receipt of materiel..................................................................................................2-5, 3-5
Site and shelter requirements .....................................................................................................2-4, 3-4
Shipment, preparation for ................................................................................................................3-21
Shipping and storage case .....................................................................................................1-10, 1-12
Special tools, TMDE, and support equipment .........................................................2-2, 3-2, Appendix C
Storage, preparation for ...................................................................................................................2-21
Storage temperature........................................................................................................................1-12
Switch .............................................................................................................................................1-15
T, U, V
Temperature limits ...........................................................................................................................1-12
Test Set
TS-3895A/UV........................................................................................................................3-8, 3-9
TS-4348/UV ...............................................................................................................................2-10
Tools
Common .........................................................................................................................Appendix B
Special ............................................................................................................................Appendix C
Troubleshooting
Direct Support..............................................................................................................................3-7
Electrical ....................................................................................................................................3-10
Table............................................................................................................................................3-7
Unit ..............................................................................................................................................2-9
W, X, Y, Z
Warranty information .........................................................................................................................1-7
Weight
Goggles .....................................................................................................................................1-12
Shipping and storage case.........................................................................................................1-12
Wired housing
Installation..................................................................................................................................3-16
Removal.....................................................................................................................................3-16
Index-5/6 blank
JOEL B. HUDSON
PIN: 070424-000