SCOM 2007 Management Pack Guide For Veritas NetBackup
SCOM 2007 Management Pack Guide For Veritas NetBackup
Symantec, the Symantec Logo, and NetBackup Operations Manager are trademarks or
registered trademarks of Symantec Corporation or its affiliates in the U.S. and other
countries. Other names may be trademarks of their respective owners.
Portions of this software are derived from the RSA Data Security, Inc. MD5 Message-
Digest Algorithm. Copyright 1991-92, RSA Data Security, Inc. Created 1991. All rights
reserved.
The product described in this document is distributed under licenses restricting its use,
copying, distribution, and decompilation/reverse engineering. No part of this document
may be reproduced in any form by any means without prior written authorization of
Symantec Corporation and its licensors, if any.
Symantec Corporation
20330 Stevens Creek Blvd.
Cupertino, CA 95014
www.symantec.com
Technical support
For technical assistance, visit http://entsupport.symantec.com and select phone
or email support. Use the Knowledge Base search feature to access resources
such as TechNotes, product alerts, software downloads, hardware compatibility
lists, and our customer email notification service
4
Contents
Note: The term SCOM in this document refers specifically to SCOM 2007.
8 Introducing Microsoft System Center Operations Manager Management Pack for Veritas NetBackup
Note: The term NetBackup alerts used in this document means alerts about
NetBackup. It does not mean that these alerts are generated by NetBackup.
Chapter 2
Integrating NOM and
SCOM 2007
This chapter describes how you can integrate NOM and SCOM to be able to
receive NetBackup alerts using SCOM 2007.
Table 2-1 on page 9 describes the sequence of steps to be followed for
integrating NOM and SCOM.
2 Install SNMP and WMI SNMP “Installing and configuring SNMP and WMI
provider on the SCOM server. SNMP provider” on page 10.
4 Deploy the SCOM Management “Deploying the SCOM Management Pack for
Pack for NetBackup. NetBackup” on page 12.
After this, the NOM MIB’s need to be compiled into Windows Management
Instrumentation (WMI) format so that SCOM can read them. The MIB files can
be compiled using the smi2smir utility. This utility loads the MIB information
into WMI and is located in C:\WINDOWS\system32\wbem\snmp directory.
12 Integrating NOM and SCOM 2007
Deploying the SCOM Management Pack for NetBackup
7 On the Discovery Method page, enter the IP address of the NOM server in
both Start and End fields, and then click Discover. The Discovery Progress
page is displayed.
Integrating NOM and SCOM 2007 15
Deploying the SCOM Management Pack for NetBackup
Note: SCOM 2007 will not be able to monitor NetBackup alerts if you do not
restart your SCOM server after importing the Management Pack.
8 Specify any email recipients if required. Click Save and Next to continue
further.
9 Select a Recipient for Trap notifications and click Finish.
The alert policy is created. When the selection criteria for this policy are met, an
SNMP trap is generated for the recipient, which can be received and displayed in
the SCOM Operations Console on clicking the Monitoring button.
Note: See the NOM online help for more information on configuring NOM. You
can access the context-sensitive help while using NOM, by clicking Help on the
title bar.
Note: See NetBackup Operations Manager Guide or the NOM online help for
more details on creating an alert policy.
Table 3-1 on page 20 lists the alert severity in NOM and the corresponding alert
severity depicted in SCOM.
Critical Critical
Major Error
Informational Information
Warning Warning
6. Drive is Down
8. Frozen Media
4. Drive is Down
9. Hung Job