Professional Documents
Culture Documents
Calculating Viscosity Index From Kinematic Viscosity at 40 and 100°C ASTM D-2270
Calculating Viscosity Index From Kinematic Viscosity at 40 and 100°C ASTM D-2270
Calculating Viscosity Index from Kinematic Viscosity at 40 and 100C ASTM D-2270
Definitions: Viscosity Index,: an arbitrary number used to characterize the variation of the kinematic viscosity of a petroleum product with temperature, the higher the viscosity index the smaller the effect of temperature on its kinematic viscosity, similarly the lower the viscosity index the higher the effect on its kinematic viscosity. Scope: This practice covers the procedures for calculating the viscosity index of petroleum products, such as lubricating oils, and related materials from their kinematic viscosities at 40 and 100C. This practice does not apply to petroleum products with kinematic viscosities less than 2.0 mm2/s @ 100C. Table 1 given in this practice applies to petroleum products with kinematic viscosities between 2 and 70 mm2/s at 100C. Equations are provided for calculating viscosity index for petroleum products having kinematic viscosities above 70 mm2/s at 100C. In cases where kinematic viscosity data are not available at temperatures of 40 and 100C, an estimate may be made of the viscosity index by calculating the kinematic viscosity at temperatures of 40 and 100C from data obtained at other temperatures. Significance and Use: The viscosity index is a widely used and accepted measure of the variation in kinematic viscosity due to changes in the temperature of a petroleum product between 40 and 100C. A higher viscosity index indicates a smaller decrease in kinematic viscosity with increasing temperature of the lubricant. The viscosity index is used in practice as a single number indicating temperature dependence of kinematic viscosity. Viscosity Index is sometimes used to characterize base oils for purposes of establishing engine testing requirements for engine oil performance categories.
Procedure: Determine the kinematic viscosity of the sample at 40 and 100C in accordance with Test Method D445, Observation: Viscosity @ 100 C = mm2/s Viscosity @ 40 C = .. mm2/s Calculation: If the kinematic viscosity of the sample at 100C is less than or equal to 70 mm2/s, extract from Table 1 the corresponding values for L and H. Measured values that are not listed, but are within the range of Table 1, may be obtained by linear interpolation. The viscosity index is not defined and shall not be reported for oils with kinematic viscosity of less than 2.0 mm2/s at 100C. If the kinematic viscosity is greater than 70 mm2/s at 100C, calculate the values of L and H as follows: L = 0.8353 Y2 + 14.67 Y 216 H = 0.1684 Y2 + 11.85 Y 97 where: L = kinematic viscosity at 40C of an oil of 0 viscosity index having the same kinematic viscosity at 100C as the oil whose viscosity index is to be calculated, mm2/s, Y = kinematic viscosity at 100C of the oil whose viscosity index is to be calculated, mm2/s, and H = kinematic viscosity at 40C of an oil of 100 viscosity index having the same kinematic viscosity at 100C as the oil whose viscosity index is to be calculated, mm2/s. If U > H, calculate the viscosity index, VI, of the oil as follows: VI = [(L-U)/(L-H) where:
U = kinematic viscosity at 40C of the oil whose viscosity index is to be calculated, mm2/s. If U < H, calculate the viscosity index, VI, of the oil as follows: VI = [((antilog N) 1/ 0.00715] + 100 where: N = (log H - log U / log Y
Result: The viscosity Index for oil having kinematic viscosity @ 100C __________ and kinematic viscosity @ 40C __________ is _________. Report: Report the viscosity index to the nearest whole number, when the number is exactly halfway between the nearest two whole numbers, round to the nearest even number. For example, 116.5 shall be
reported as 116.