Professional Documents
Culture Documents
Siprotec 4 7Sj64 Multifunction Protection Relay With Synchronization
Siprotec 4 7Sj64 Multifunction Protection Relay With Synchronization
Description The SIPROTEC 4 7SJ64 can be used as a protective control and monitoring relay for distribution feeders and transmission lines of any voltage in networks that are earthed (grounded), low-resistance earthed, unearthed, or of a compensated neutral point structure. The relay is suited for networks that are radial or looped, and for lines with single or multi-terminal feeds. The SIPROTEC 4 7SJ64 is equipped with a synchronization function which provides the operation modes synchronization check (classical) and synchronous/asynchronous switching (which takes the CB mechanical delay into consideration). Motor protection comprises undercurrent monitoring, starting time supervision, restart inhibit, locked rotor, load jam protection as well as motor statistics. The 7SJ64 is featuring the "flexible protection functions". Up to 20 protection functions can be added according to individual requirements. Thus, for example, rate-of-frequency-change protection or reverse power protection can be implemented.
The relay provides easy-to-use local control and automation functions. The number of controllable switchgear depends only on the number of available inputs and outputs. The integrated programmable logic (CFC) allows the user to implement their own functions, e.g. for the automation of switchgear (interlocking). CFC capacity is much larger compared to 7SJ63 due to extended CPU power. The user is able to generate user-defined messages as well. The flexible communication interfaces are open for modern communication architectures with control systems.
Protection functions Time-overcurrent protection Directional time-overcurrent protection Sensitive dir./non-dir. earth-fault detection Displacement voltage Intermittent earth-fault protection High-impedance restricted earth fault Inrush restraint Motor protection Overload protection Temperature monitoring Under-/overvoltage protection Under-/overfrequency protection Rate-of-frequency-change protection Power protection (e.g. reverse, factor) Breaker failure protection Negative-sequence protection Phase-sequence monitoring Synchronization Auto-reclosure Fault locator Lockout Control functions/programmable logic Flexible number of switching devices Position of switching elements is shown on the graphic display Local/remote switching via keyoperated switch Control via keyboard, binary inputs, DIGSI 4 or SCADA system Extended user-defined logic with CFC (e.g. interlocking) Monitoring functions Operational measured values V, I, f,... Energy metering values Wp, Wq Circuit-breaker wear monitoring Slave pointer Trip circuit supervision Fuse failure monitor 8 oscillographic fault records Motor statistics Communication interfaces
System interface IEC 60870-5-103, IEC 61850 PROFIBUS-FMS / DP DNP 3.0 / MODBUS RTU Service interface for DIGSI 4 (modem) Additional interface for temperature detection (RTD-box) Front interface for DIGSI 4 Time synchronization via IRIG B/DCF77
LSP2316-afpen.tif
5/183
Application
The SIPROTEC 4 7SJ64 unit is a numerical protection relay that also performs control and monitoring functions and therefore supports the user in cost-effective power system management, and ensures reliable supply of electric power to the customers. Local operation has been designed according to ergonomic criteria. A large, easy-to-read graphic display was a major design aim. Control The integrated control function permits control of disconnect devices (electrically operated/motorized switches) or circuit-breakers via the integrated operator panel, binary inputs, DIGSI 4 or the control and protection system (e.g. SICAM). The present status (or position) of the primary equipment can be displayed. 7SJ64 supports substations with single and duplicate busbars. The number of elements that can be controlled (usually 1 to 5) is only restricted by the number of inputs and outputs available. A full range of command processing functions is provided.
Programmable logic The integrated logic characteristics (CFC) allow users to implement their own functions for automation of switchgear (interlocking) or a substation via a graphic user interface. Due to extended CPU power, the programmable logic capacity is much larger compared to 7SJ63. The user can also generate user-defined messages. Line protection The 7SJ64 units can be used for line protection of high and medium-voltage networks with earthed, low-resistance earthed, isolated or compensated neutral point. Synchronization In order to connect two components of a power system, the relay provides a synchronization function which verifies that switching ON does not endanger the stability of the power system. The synchronization function provides the operation modes synchro-check (classical) and synchronous/asynchronous switching (which takes the c.-b. mechanical delay into consideration).
Motor protection When protecting motors, the relays are suitable for asynchronous machines of all sizes. Transformer protection The 7SJ64 units perform all functions of backup protection supplementary to transformer differential protection. The inrush suppression effectively prevents tripping by inrush currents. The high-impedance restricted earth-fault protection detects short-circuits and insulation faults of the transformer. Backup protection The relays can be used universally for backup protection. Flexible protection functions By configuring a connection between a standard protection logic and any measured or derived quantity, the functional scope of the relays can be easily expanded by up to 20 protection stages or protection functions. Metering values Extensive measured values, limit values and metered values permit improved system management.
5/184
Application
ANSI No. IEC I>, I>>, I>>> IE>, IE>>, IE>>> I>>>>, I2> IE>>>> Ip, IEp Protection functions Definite-time overcurrent protection (phase/neutral) Additional definite-time overcurrent protection stages (phase/neutral) via flexible protection functions Inverse-time overcurrent protection (phase/neutral), phase function with voltage-dependent option
Idir>, Idir>>, Ip dir Directional time-overcurrent protection IEdir>, IEdir>>, IEp dir (definite/inverse, phase/neutral) Directional comparison protection IEE>, IEE>>, IEEp Directional/non-directional sensitive earth-fault detection Cold load pick-up (dynamic setting change) VE, V0> IIE> Displacement voltage, zero-sequence voltage Intermittent earth fault High-impedance restricted earth-fault protection Breaker failure protection Auto-reclosure Synchronization I2> V2>, phase seq. > Phase-balance current protection (negative-sequence protection) Unbalance-voltage protection and/or phase-sequence monitoring Thermal overload protection Starting time supervision Load jam protection Locked rotor protection Restart inhibit I< Undercurrent monitoring Temperature monitoring via external device, e.g. bearing temperature monitoring V<, V> P<>, Q<> cos f>, f< df/dt Undervoltage/overvoltage protection Reverse-power, forward-power protection Power factor protection Overfrequency/underfrequency protection Rate-of-frequency-change protection Fault locator
67Ns/50Ns 59N/64 87N 50BF 79M 25 46 47 49 48 51M 14 66/86 37 38 27, 59 32 55 81O/U 81R 21FL
5/185
Construction Connection techniques and housing with many advantages 1/3, 1/2 and 1/1-rack sizes These are the available housing widths of the 7SJ64 relays, referred to a 19 module frame system. This means that previous models can always be replaced. The height is a uniform 244 mm for flush-mounting housings and 266 mm for surfacemounting housings for all housing widths. All cables can be connected with or without ring lugs. Plug-in terminals are available as an option. It is thus possible to employ prefabricated cable harnesses. In the case of surface mounting on a panel, the connection terminals are located above and below in the form of screw-type terminals. The communication interfaces are located in a sloped case at the top and bottom of the housing. The housing can also be supplied optionally with a detached operator panel (refer to Fig. 5/171), or without operator panel, in order to allow optimum operation for all types of applications.
LSP2174-afp.tif
LSP2299-bfpen.tif LSP2219-afpen.eps
Fig. 5/171 Housing with plug-in terminals and detached operator panel
5/186
LSP2237-afp.tif
LSP2196-afp.eps
Protection functions Time-overcurrent protection (ANSI 50, 50N, 51,51V, 51N) This function is based on the phase-selective measurement of the three phase currents and the earth current (four transformers). Three definite-time overcurrent protection elements (DMT) exist both for the phases and for the earth. The current threshold and the delay time can be set in a wide range. In addition, inverse-time overcurrent protection characteristics (IDMTL) can be activated. The inverse-time function provides as an option voltage-restraint or voltage-controlled operating modes. With the "flexible protection functions", further definite-time overcurrent stages can be implemented in the 7SJ64 unit.
Reset characteristics For easier time coordination with electromechanical relays, reset characteristics according to ANSI C37.112 and IEC 60255-3 / BS 142 standards are applied. When using the reset characteristic (disk emulation), a reset process is initiated after the fault current has disappeared. This reset process corresponds to the reverse movement of the Ferraris disk of an electromechanical relay (thus: disk emulation). User-definable characteristics Instead of the predefined time characteristics according to ANSI, tripping characteristics can be defined by the user for phase and earth units separately. Up to 20 current/ time value pairs may be programmed. They are set as pairs of numbers or graphically in DIGSI 4.
Inrush restraint The relay features second harmonic restraint. If the second harmonic is detected during transformer energization, pickup of non-directional and directional normal elements are blocked. Cold load pickup/dynamic setting change For directional and nondirectional timeovercurrent protection functions the initiation thresholds and tripping times can be switched via binary inputs or by time control.
5/187
Protection functions Directional time-overcurrent protection (ANSI 67, 67N) Directional phase and earth protection are separate functions. They operate in parallel to the non-directional overcurrent elements. Their pickup values and delay times can be set separately. Definite-time and inverse-time characteristic is offered. The tripping characteristic can be rotated about 180 degrees. By means of voltage memory, directionality can be determined reliably even for close-in (local) faults. If the switching device closes onto a fault and the voltage is too low to determine direction, directio- nality (directional decision) is made with voltage from the voltage memory. If no voltage exists in the memory, tripping occurs according to the coordination schedule. For earth protection, users can choose whether the direction is to be determined via zero-sequence system or negative-sequence system quantities (selectable). Using negative-sequence variables can be advantageous in cases where the zero voltage tends to be very low due to unfavorable zero-sequence impedances. Directional comparison protection (cross-coupling) It is used for selective protection of sections fed from two sources with instantaneous tripping, i.e. without the disadvantage of time coordination. The directional comparison protection is suitable if the distances between the protection stations are not significant and pilot wires are available for signal transmission. In addition to the directional comparison protection, the directional coordinated time-overcurrent protection is used for complete selective backup protection. If operated in a closed-circuit connection, an interruption of the transmission line is detected. (Sensitive) directional earth-fault detection (ANSI 64, 67Ns/67N) For isolated-neutral and compensated networks, the direction of power flow in the zero sequence is calculated from the zero-sequence current I0 and zero-sequence voltage V0. For networks with an isolated neutral, the reactive current component is evaluated; for compensated networks, the active current component or residual resistive current is evaluated.
Fig. 5/176 Directional characteristic of the directional time-overcurrent protection
Fig. 5/177 Directional determination using cosine measurements for compensated networks
For special network conditions, e.g. high-resistance earthed networks with ohmic-capacitive earth-fault current or low-resistance earthed networks with ohmic-inductive current, the tripping characteristics can be rotated approximately 45 degrees. Two modes of earth-fault direction detection can be implemented: tripping or signalling only mode. It has the following functions: TRIP via the displacement voltage VE. Two instantaneous elements or one instantaneous plus one user-defined characteristic. Each element can be set in forward, reverse, or non-directional.
The function can also be operated in the insensitive mode, as an additional short-circuit protection. (Sensitive) earth-fault detection (ANSI 50Ns, 51Ns/50N, 51N) For high-resistance earthed networks, a sensitive input transformer is connected to a phase-balance neutral current transformer (also called core-balance CT). The function can also be operated in the insensitive mode, as an additional shortcircuit protection.
5/188
Protection functions Intermittent earth-fault protection Intermittent (re-striking) faults occur due to insulation weaknesses in cables or as a result of water penetrating cable joints. Such faults either simply cease at some stage or develop into lasting short-circuits. During intermittent activity, however, star-point resistors in networks that are impedance-earthed may undergo thermal overloading. The normal earth-fault protection cannot reliably detect and interrupt the current pulses, some of which can be very brief. The selectivity required with intermittent earth faults is achieved by summating the duration of the individual pulses and by triggering when a (settable) summed time is reached. The response threshold IIE> evaluates the r.m.s. value, referred to one systems period. Phase-balance current protection (ANSI 46) (Negative-sequence protection) In line protection, the two-element phasebalance current/negative-sequence protection permits detection on the high side of high-resistance phase-to-phase faults and phase-to-earth faults that are on the low side of a transformer (e.g. with the switch group Dy 5). This provides backup protection for high-resistance faults beyond the transformer. Breaker failure protection (ANSI 50BF) If a faulted portion of the electrical circuit is not disconnected upon issuance of a trip command, another command can be initiated using the breaker failure protection which operates the circuit-breaker, e.g. of an upstream (higher-level) protection relay. Breaker failure is detected if, after a trip command, current is still flowing in the faulted circuit. As an option, it is possible to make use of the circuit-breaker position indication. Auto-reclosures (ANSI 79) Multiple reclosures can be defined by the user and lockout will occur if a fault is present after the last reclosure. The following functions are possible: 3-pole ARC for all types of faults Separate settings for phase and earth faults Multiple ARC, one rapid auto-reclosure (RAR) and up to nine delayed auto-reclosures (DAR) Starting of the ARC depends on the trip command selection (e.g. 46, 50, 51, 67)
Fig. 5/178
Blocking option of the ARC via binary inputs ARC can be initiated externally or via CFC The directional and non-directional elements can either be blocked or operated non-delayed depending on the autoreclosure cycle Dynamic setting change of the directional and non-directional elements can be activated depending on the ready AR The AR CLOSE command can be given synchronous by use of the synchronization function. Flexible protection functions The 7SJ64 units enable the user to easily add on up to 20 protective functions. To this end, parameter definitions are used to link a standard protection logic with any chosen characteristic quantity (measured or derived quantity) (Fig. 5/178). The standard logic consists of the usual protection elements such as the pickup message, the parameterdefinable delay time, the TRIP command, a blocking possibility, etc. The mode of operation for current, voltage, power and power factor quantities can be three-phase or single-phase. Almost all quantities can be operated as greater than or less than stages. All stages operate with protection priority.
5
Protection stages/functions attainable on the basis of the available characteristic quantities:
Function I>, IE> V<, V>, VE> 3I0>, I1>, I2>, I2/I1 3V0>, V1><, V2>< P><, Q>< cos (p.f.)>< f>< df/dt>< ANSI No. 50, 50N 27, 59, 64 50N, 46 59N, 47 32 55 81O, 81U 81R
For example, the following can be implemented: Reverse power protection (ANSI 32R) Rate-of-frequency-change protection (ANSI 81R) Synchronization (ANSI 25) In case of switching ON the circuit-breaker, the units can check whether the two subnetworks are synchronized (classic synchro-check). Furthermore, the synchronizing function may operate in the Synchronous/asynchronous switching mode. The unit then distinguishes between synchronous and asynchronous networks: In synchronous networks, frequency differences between the two subnetworks are almost non-existant. In this case, the circuitbreaker operating time does not need to be considered. Under asynchronous condition, however, this difference is markedly larger and the time window for switching is shorter. In this case, it is recommended to consider the operating time of the circuitbreaker.
5/189
Protection functions The command is automatically pre-dated by the duration of the operating time of the circuit-breaker, thus ensuring that the contacts of the CB close at exactly the right time. Up to 4 sets of parameters for the synchronizing function can be stored in the unit. This is an important feature when several circuit-breakers with different operating times are to be operated by one single relay. Thermal overload protection (ANSI 49) For protecting cables and transformers, an overload protection with an integrated pre-warning element for temperature and current can be applied. The temperature is calculated using a thermal homogeneousbody model (according to IEC 60255-8), which takes account both of the energy entering the equipment and the energy losses. The calculated temperature is constantly adjusted accordingly. Thus, account is taken of the previous load and the load fluctuations. For thermal protection of motors (especially the stator), a further time constant can be set so that the thermal ratios can be detected correctly while the motor is rotating and when it is stopped. The ambient temperature or the temperature of the coolant can be detected serially via an external temperature monitoring box (resistance-temperature detector box, also called RTD- box). The thermal replica of the overload function is automatically adapted to the ambient conditions. If there is no RTD-box it is assumed that the ambient temperatures are constant. High-impedance restricted earth-fault protection (ANSI 87N) The high-impedance measurement principle is an uncomplicated and sensitive method for detecting earth faults, especially on transformers. It can also be applied to motors, generators and reactors when these are operated on an earthed network. When the high-impedance measurement principle is applied, all current transformers in the protected area are connected in parallel and operated on one common resistor of relatively high R whose voltage is measured (see Fig. 5/179). In the case of 7SJ6 units, the voltage is measured by detecting the current through the (external) resistor R at the sensitive current measurement input IEE.
n Motor protection
Restart inhibit (ANSI 66/86) If a motor is started up too many times in succession, the rotor can be subject to thermal overload, especially the upper edges of the bars. The rotor temperature is calculated from the stator current. The reclosing lockout only permits start-up of the motor if the rotor has sufficient thermal reserves for a complete start-up (see Fig. 5/180). Emergency start-up This function disables the reclosing lockout via a binary input by storing the state of the thermal replica as long as the binary input is active. It is also possible to reset the thermal replica to zero. Temperature monitoring (ANSI 38) The varistor V serves to limit the voltage in the event of an internal fault. It cuts off the high momentary voltage spikes occurring at transformer saturation. At the same time, this results in smoothing of the voltage without any noteworthy reduction of the average value. If no faults have occurred and in the event of external faults, the system is at equilibrium, and the voltage through the resistor is approximately zero. In the event of internal faults, an imbalance occurs which leads to a voltage and a current flow through the resistor R. The current transformers must be of the same type and must at least offer a separate core for the high-impedance restricted earth-fault protection. They must in particular have the same transformation ratio and an approximately identical knee-point voltage. They should also demonstrate only minimal measuring errors. Settable dropout delay times If the devices are used in parallel with electromechanical relays in networks with intermittent faults, the long dropout times of the electromechanical devices (several hundred milliseconds) can lead to problems in terms of time grading. Clean time grading is only possible if the dropout time is approximately the same. This is why the parameter of dropout times can be defined for certain functions such as time-overcurrent protection, earth short-circuit and phasebalance current protection. Up to two temperature monitoring boxes with a total of 12 measuring sensors can be used for temperature monitoring and detection by the protection relay. The thermal status of motors, generators and transformers can be monitored with this device. Additionally, the temperature of the bearings of rotating machines are monitored for limit value violation. The temperatures are being measured with the help of temperature detectors at various locations of the device to be protected. This data is transmitted to the protection relay via one or two temperature monitoring boxes (see Accessories, page 5/219).
5/190
Protection functions Starting time supervision (ANSI 48/14) Starting time supervision protects the motor against long unwanted start-ups that might occur in the event of excessive load torque or excessive voltage drops within the motor, or if the rotor is locked. Rotor temperature is calculated from measured stator current. The tripping time is calculated according to the following equation: for I > IMOTOR START
I t = A TA I I = Actual current flowing IMOTOR START = Pickup current to detect a motor start t = Tripping time = Rated motor starting current IA = Tripping time at rated motor TA starting current (2 times, for warm and cold motor)
2
5
Fig. 5/180
Phase-balance current protection (ANSI 46) (Negative-sequence protection) The negative-sequence / phase-balance current protection detects a phase failure or load unbalance due to network asymmetry and protects the rotor from impermissible temperature rise. Undercurrent monitoring (ANSI 37) With this function, a sudden drop in current, which can occur due to a reduced motor load, is detected. This may be due to shaft breakage, no-load operation of pumps or fan failure. Motor statistics Essential information on start-up of the motor (duration, current, voltage) and general information on number of starts, total operating time, total down time, etc. are saved as statistics in the device.
n Voltage protection
Overvoltage protection (ANSI 59) The two-element overvoltage protection detects unwanted network and machine overvoltage conditions. The function can operate either with phase-to-phase, phaseto-earth, positive phase-sequence or negative phase-sequence voltage. Three-phase and single-phase connections are possible. Undervoltage protection (ANSI 27) The two-element undervoltage protection provides protection against dangerous voltage drops (especially for electric machines). Applications include the isolation of generators or motors from the network to avoid undesired operating states and a possible loss of stability. Proper operating conditions of electrical machines are best evaluated with the positive-sequence quantities. The protection function is active over a wide frequency range (45 to 55, 55 to 65 Hz)1). Even when falling below this frequency range the function continues to work, however, with a greater tolerance band. The function can operate either with phase-to-phase, phase-to-earth or positive phase-sequence voltage, and can be monitored with a current criterion. Three-phase and single-phase connections are possible. Frequency protection (ANSI 81O/U) Frequency protection can be used for overfrequency and underfrequency protection. Electric machines and parts of the system are
The characteristic (equation) can be adapted optimally to the state of the motor by applying different tripping times TA in dependence of either cold or warm motor state. For differentiation of the motor state the thermal model of the rotor is applied. If the trip time is rated according to the above formula, even a prolonged start-up and reduced voltage (and reduced start-up current) will be evaluated correctly. The tripping time is inverse (current dependent). A binary signal is set by a speed sensor to detect a blocked rotor. An instantaneous tripping is effected. Load jam protection (ANSI 51M) Sudden high loads can cause slowing down and blocking of the motor and mechanical damages. The rise of current due to a load jam is being monitored by this function (alarm and tripping). The overload protection function is too slow and therefore not suitable under these circumstances.
5/191
Protection functions/Functions protected from unwanted speed deviations. Unwanted frequency changes in the network can be detected and the load can be removed at a specified frequency setting. Frequency protection can be used over a wide frequency range (40 to 60, 50 to 70 Hz)1). There are four elements (selectable as overfrequency or underfrequency) and each element can be delayed separately. Blocking of the frequency protection can be performed if using a binary input or by using an undervoltage element. Fault locator (ANSI 21FL) The integrated fault locator calculates the fault impedance and the distance-to-fault. The results are displayed in , kilometers (miles) and in percent of the line length. Circuit-breaker wear monitoring Methods for determining circuit-breaker contact wear or the remaining service life of a circuit-breaker (CB) allow CB maintenance intervals to be aligned to their actual degree of wear. The benefit lies in reduced maintenance costs. There is no mathematically exact method of calculating the wear or the remaining service life of circuit-breakers that takes into account the arc-chamber's physical conditions when the CB opens. This is why various methods of determining CB wear have evolved which reflect the different operator philosophies. To do justice to these, the devices offer several methods: I I x, with x = 1... 3 i 2t The devices additionally offer a new method for determining the remaining service life: Two-point method The CB manufacturers double-logarithmic switching cycle diagram (see Fig. 5/181) and the breaking current at the time of contact opening serve as the basis for this method. After CB opening, the two-point method calculates the number of still possible switching cycles. To this end, the two points P1 and P2 only have to be set on the device. These are specified in the CB's technical data. All of these methods are phase-selective and a limit value can be set in order to obtain an alarm if the actual value falls below or exceeds the limit value during determination of the remaining service life.
1) The 40 to 60, 50 to 70 Hz range is available for fN = 50/60 Hz.
Commissioning Commissioning could hardly be easier and is fully supported by DIGSI 4. The status of the binary inputs can be read individually and the state of the binary outputs can be set individually. The operation of switching elements (circuit-breakers, disconnect devices) can be checked using the switching functions of the bay controller. The analog measured values are represented as wide-ranging operational measured values. To prevent transmission of information to the control center during maintenance, the bay controller communications can be disabled to prevent unnecessary data from being transmitted. During commissioning, all indications with test marking for test purposes can be connected to a control and protection system. Test operation During commissioning, all indications can be passed to an automatic control system for test purposes.
Fig. 5/181
Switching authority Switching authority is determined according to parameters, communication or by keyoperated switch (when available). If a source is set to LOCAL, only local switching operations are possible. The following sequence of switching authority is laid down: LOCAL; DIGSI PC program, REMOTE. Key-operated switch 7SJ64 units are fitted with key-operated switch function for local/remote changeover and changeover between interlocked switching and test operation. Command processing All the functionality of command processing is offered. This includes the processing of single and double commands with or without feedback, sophisticated monitoring of the control hardware and software, checking of the external process, control actions using functions such as runtime monitoring and automatic command termination after output. Here are some typical applications: Single and double commands using 1, 1 plus 1 common or 2 trip contacts User-definable bay interlocks Operating sequences combining several switching operations such as control of circuit-breakers, disconnectors and earthing switches Triggering of switching operations, indications or alarm by combination with existing information
Siemens SIP 2008
5/192
Functions Motor control The SIPROTEC 4 7SJ64 with high performance relays is well-suited for direct activation of the circuit-breaker, disconnector and earthing switch operating mechanisms in automated substations. Interlocking of the individual switching devices takes place with the aid of programmable logic. Additional auxiliary relays can be eliminated. This results in less wiring and engineering effort. Assignment of feedback to command The positions of the circuit-breaker or switching devices and transformer taps are acquired by feedback. These indication inputs are logically assigned to the corresponding command outputs. The unit can therefore distinguish whether the indication change is a consequence of switching operation or whether it is a spontaneous change of state. Chatter disable Chatter disable feature evaluates whether, in a configured period of time, the number of status changes of indication input exceeds a specified figure. If exceeded, the indication input is blocked for a certain period, so that the event list will not record excessive operations. Indication filtering and delay Binary indications can be filtered or delayed. Filtering serves to suppress brief changes in potential at the indication input. The indication is passed on only if the indication voltage is still present after a set period of time. In the event of indication delay, there is a wait for a preset time. The information is passed on only if the indication voltage is still present after this time. Indication derivation A further indication (or a command) can be derived from an existing indication. Group indications can also be formed. The volume of information to the system interface can thus be reduced and restricted to the most important signals.
5
Fig. 5/182 Typical wiring for 7SJ642 motor direct control (simplified representation without fuses) Binary output BO6 and BO7 are interlocked so that only one set of contacts are closed at a time.
Fig. 5/183
Fig. 5/184
5/193
Functions Measured values The r.m.s. values are calculated from the acquired current and voltage along with the power factor, frequency, active and reactive power. The following functions are available for measured value processing: Currents IL1, IL2, IL3, IE, IEE (67Ns) Voltages VL1, VL2, VL3, VL1L2, VL2L3, VL3L1, Vsyn Symmetrical components I1, I2, 3I0; V1, V2, V0 Power Watts, Vars, VA/P, Q, S (P, Q: total and phase-selective) Power factor (cos ) (total and phase-selective) Frequency Energy kWh, kVArh, forward and reverse power flow Mean as well as minimum and maximum current and voltage values Operating hours counter Mean operating temperature of overload function Limit value monitoring Limit values are monitored using programmable logic in the CFC. Commands can be derived from this limit value indication. Zero suppression In a certain range of very low measured values, the value is set to zero to suppress interference.
Metered values For internal metering, the unit can calculate an energy metered value from the measured current and voltage values. If an external meter with a metering pulse output is available, the SIPROTEC 4 unit can obtain and process metering pulses via an indication input. The metered values can be displayed and passed on to a control center as an accumulation with reset. A distinction is made between forward, reverse, active and reactive energy. Switchgear cubicles for high/medium voltage All units are designed specifically to meet the requirements of high/medium-voltage applications.
LSP2078-afp.eps
In general, no separate measuring instruments (e.g. for current, voltage, frequency measuring transducer ...) or additional control components are necessary.
5/194
Communication In terms of communication, the units offer substantial flexibility in the context of connection to industrial and power automation standards. Communication can be extended or added on thanks to modules for retrofitting on which the common protocols run. Therefore, also in the future it will be possible to optimally integrate units into the changing communication infrastructure, for example in Ethernet networks (which will also be used increasingly in the power supply sector in the years to come). Serial front interface There is a serial RS232 interface on the front of all the units. All of the units functions can be set on a PC by means of the DIGSI 4 protection operation program. Commissioning tools and fault analysis are also built into the program and are available through this interface. Rear-mounted interfaces1) A number of communication modules suitable for various applications can be fitted in the rear of the flush-mounting housing. In the flush-mounting housing, the modules can be easily replaced by the user. The interface modules support the following applications: Time synchronization interface All units feature a permanently integrated electrical time synchronization interface. It can be used to feed timing telegrams in IRIG-B or DCF77 format into the units via time synchronization receivers. System interface Communication with a central control system takes place through this interface. Radial or ring type station bus topologies can be configured depending on the chosen interface. Furthermore, the units can exchange data through this interface via Ethernet and IEC 61850 protocol and can also be operated by DIGSI. Service interface The service interface was conceived for remote access to a number of protection units via DIGSI. It can be an electrical RS232/RS485 interface. For special applications, a maximum of two temperature monitoring boxes (RTD-box) can be connected to this interface as an alternative. Additional interface Up to 2 RTD-boxes can be connected via this interface.
System interface protocols (retrofittable) IEC 61850 protocol As of mid-2004, the Ethernet-based IEC 61850 protocol is the worldwide standard for protection and control systems used by power supply corporations. Siemens is the first manufacturer to support this standard. By means of this protocol, information can also be exchanged directly between bay units so as to set up simple masterless systems for bay and system interlocking. Access to the units via the Ethernet bus will also be possible with DIGSI. It will also be possible to retrieve operating and fault messages and fault recordings via a browser. This Web monitor will also provide a few items of unit-specific information in browser windows. IEC 60870-5-103 protocol The IEC 60870-5-103 protocol is an international standard for the transmission of protective data and fault recordings. All messages from the unit and also control commands can be transferred by means of published, Siemens-specific extensions to the protocol. Redundant solutions are also possible. Optionally it is possible to read out and alter individual parameters (only possible with the redundant module). PROFIBUS-FMS PROFIBUS-FMS is an internationally standardized communication system (EN 50170) for efficient performance of communication tasks in the bay area. SIPROTEC 4 units use a profile specially optimized for protection and control requirements. DIGSI can also work on the basis of PROFIBUS-FMS. The units are linked to a SICAM automation system. PROFIBUS-DP protocol PROFIBUS-DP is the most widespread protocol in industrial automation. Via PROFIBUS-DP, SIPROTEC units make their information available to a SIMATIC controller or, in the control direction, receive commands from a central SIMATIC. Measured values can also be transferred. MODBUS RTU protocol This uncomplicated, serial protocol is mainly used in industry and by power supply corporations, and is supported by a number of unit manufacturers. SIPROTEC units function as MODBUS slaves, making their information available to a master or receiving information from it. A time-stamped event list is available.
Fig. 5/188 Bus structure for station bus with Ethernet and IEC 61850, fiber-optic ring
1) For units in panel surface-mounting housings please refer to note on page 5/215.
5/195
Communication DNP 3.0 protocol Power supply corporations use the serial DNP 3.0 (Distributed Network Protocol) for the station and network control levels. SIPROTEC units function as DNP slaves, supplying their information to a master system or receiving information from it. System solutions for protection and station control Together with the SICAM power automation system, SIPROTEC 4 can be used with PROFIBUS-FMS. Over the low-cost electrical RS485 bus, or interference-free via the optical double ring, the units exchange information with the control system. Units featuring IEC 60870-5-103 interfaces can be connected to SICAM in parallel via the RS485 bus or radially by fiber-optic link. Through this interface, the system is open for the connection of units of other manufacturers (see Fig. 5/186). Because of the standardized interfaces, SIPROTEC units can also be integrated into systems of other manufacturers or in SIMATIC. Electrical RS485 or optical interfaces are available. The optimum physical data transfer medium can be chosen thanks to opto-electrical converters. Thus, the RS485 bus allows low-cost wiring in the cubicles and an interference-free optical connection to the master can be established. For IEC 61850, an interoperable system solution is offered with SICAM PAS. Via the 100 Mbits/s Ethernet bus, the units are linked with PAS electrically or optically to the station PC. The interface is standardized, thus also enabling direct connection of units of other manufacturers to the Ethernet bus. With IEC 61850, however, the units can also be used in other manufacturers systems (see Fig. 5/188).
Fig. 5/190 Optical Ethernet communication module for IEC 61850 with integrated Ethernet-switch
5/196
LSP2810,tif
Typical connections
n Connection of current
Standard connection
For earthed networks, the earth current is obtained from the phase currents by the residual current circuit.
5/197
Typical connections Connection for compensated networks The figure shows the connection of two phase-to-earth voltages and the VE voltage of the open delta winding and a phase-earth neutral current transformer for the earth current. This connection maintains maximum precision for directional earth- fault detection and must be used in compensated networks. Fig. 5/194 shows sensitive directional earth-fault detection.
Fig. 5/194 Sensitive directional earth-fault detection with directional element for phases
5
Connection for isolated-neutral or compensated networks only If directional earth-fault protection is not used, the connection can be made with only two phase current transformers. Directional phase short-circuit protection can be achieved by using only two primary transformers.
Connection for the synchronization function The 3-phase system is connected as reference voltage, i. e. the outgoing voltages as well as a single-phase voltage, in this case a busbar voltage, that has to be synchronized.
Fig. 5/196 Measuring of the busbar voltage and the outgoing feeder voltage for synchronization
5/198
(Low-resistance) earthed networks Isolated or compensated networks (Low-resistance) earthed networks Isolated or compensated networks (Low-resistance) earthed networks
Residual circuit, with 3 phase-current Phase-to-earth connection or transformers possible phase-to-phase connection Residual circuit, with 3 or 2 phasecurrent transformers possible Phase-to-earth connection or phase-to-phase connection
Residual circuit, with 3 phase-current Phase-to-earth connection required transformers required, phase-balance neutral current transformers possible Residual circuit, if earth current > 0.05 IN on secondary side, otherwise phase-balance neutral current transformers required Phase-balance neutral current transformers required 3 times phase-to-earth connection or phase-to-earth connection with open delta winding Phase-to-earth connection with open delta winding required
Isolated networks
Compensated networks
n Application examples
Synchronization function When two subnetworks must be interconnected, the synchronization function monitors whether the subnetworks are synchronous and can be connected without risk of losing stability. As shown in Fig. 5/197, load is being fed from a generator to a busbar via a transformer. It is assumed that the frequency difference of the 2 subnetworks is such that the device determines asynchronous system conditions. The voltages of the busbar and the feeder should be the same when the contacts are made; to ensure this condition the synchronism function must run in the synchronous/asynchronous switching mode. In this mode, the operating time of the CB can be set within the relay. Differences between angle and frequency can then be calculated by the relay while taking into account the operating time of the CB. From these differences, the unit derives the exact time for issuing the CLOSE command under asynchronous conditions. When the contacts close, the voltages will be in phase.
The vector group of the transformer can be considered by setting parameters. Thus no external circuits for vector group adaptation are required. This synchronism function can be applied in conjunction with the auto-reclosure function as well as with the control function CLOSE commands (local/remote).
Fig. 5/197
5/199
Typical applications
n Connection of circuit-breaker
Undervoltage releases Undervoltage releases are used for automatic tripping of high-voltage motors. Example: DC supply voltage of control system fails and manual electric tripping is no longer possible. Automatic tripping takes place when voltage across the coil drops below the trip limit. In Figure 5/198, tripping occurs due to failure of DC supply voltage, by automatic opening of the live status contact upon failure of the protection unit or by short-circuiting the trip coil in event of a network fault.
5
Fig. 5/198 Undervoltage release with make contact 50, 51
In Fig. 5/199 tripping is by failure of auxiliary voltage and by interruption of tripping circuit in the event of network failure. Upon failure of the protection unit, the tripping circuit is also interrupted, since contact held by internal logic drops back into open position.
Fig. 5/199
5/200
Typical applications Trip circuit supervision (ANSI 74TC) One or two binary inputs can be used for monitoring the circuit-breaker trip coil including its incoming cables. An alarm signal occurs whenever the circuit is interrupted. Lockout (ANSI 86) All binary outputs can be stored like LEDs and reset using the LED reset key. The lockout state is also stored in the event of supply voltage failure. Reclosure can only occur after the lockout state is reset. Reverse-power protection for dual supply (ANSI 32R) If power is fed to a busbar through two parallel infeeds, then in the event of any fault on one of the infeeds it should be selectively interrupted. This ensures a continued supply to the busbar through the remaining infeed. For this purpose, directional devices are needed which detect a short-circuit current or a power flow from the busbar in the direction of the infeed. The directional timeovercurrent protection is usually set via the load current. It cannot be used to deactivate low-current faults. Reverse-power protection can be set far below the rated power. This ensures that it also detects power feedback into the line in the event of low-current faults with levels far below the load current. Reverse-power protection is performed via the flexible protection functions of the 7SJ64.
5
Fig. 5/200 Trip circuit supervision with 2 binary inputs
Fig. 5/201
5/201
Technical data
General unit data Measuring circuits System frequency Current transformer Rated current Inom Option: sensitive earth-fault CT Power consumption at Inom = 1 A at Inom = 5 A for sensitive earth-fault CT at 1 A Overload capability Thermal (effective) 1 or 5 A (settable) IEE < 1.6 A Approx. 0.05 VA per phase Approx. 0.3 VA per phase Approx. 0.05 VA 100 x Inom for 1 s 30 x Inom for 10 s 4 x Inom continuous 250 x Inom (half cycle) 50 / 60 Hz (settable) Binary inputs/indication inputs Type Number (marshallable) Voltage range Pickup threshold modifiable by plug-in jumpers Pickup threshold DC 19 V DC 88 V DC 110/125/220/250 V DC For rated control voltage DC 24/48/60/110/ 125 V DC Power consumption energized 7SJ640 7 7SJ641 15 7SJ642 20 7SJ645 33 7SJ647 48
24 - 250 V DC
0.9 mA (independent of operating voltage) for BI 819 / 2132; 1.8 mA for BI 17 / 20/3348 7SJ640 7SJ641 13 7SJ642 8 7SJ645 11 7SJ647 21
Binary outputs/command outputs Type Contacts per command/ indication relay Live status contact Switching capacity Make Break Command/indication relay 5
Overload capability if equipped with sensitive earth-fault CT Thermal (effective) 300 A for 1 s 100 A for 10 s 15 A continuous Dynamic (impulse current) 750 A (half cycle) Voltage transformer Rated voltage Vnom Measuring range Overload capability in voltage path (phase-neutral voltage) Thermal (effective) Rated auxiliary voltage Vaux DC Permissible tolerance Ripple voltage, peak-to-peak Power consumption Quiescent Energized Backup time during loss/short-circuit of auxiliary direct voltage Rated auxiliary voltage Vaux AC Permissible tolerance Power consumption Quiescent Energized AC DC 100 V to 225 V 0 V to 200 V
1 NO / form A 1 NO / NC (jumper)/form A/B 1000 W / VA 30 W / VA / 40 W resistive/ 25 W at L/R 50 ms 250 V DC 5 A continuous, 30 A for 0.5 s making current, 2000 switching cycles 7SJ640 7SJ641 0 7SJ642 2 (4) 7SJ645 4 (8) 7SJ647 4 (8)
Power relay (for motor control) Type Number Number of contacts/relay Switching capacity Make Break 7.5 W 21 W Switching voltage Permissible current
12 % of rated auxiliary voltage 7SJ640 7SJ641 7SJ645 7SJ642 Approx. 5 W Approx. 9 W 5.5 W 6.5 W 12.5 W 15 W
2 NO / form A 1000 W / VA at 48 V 250 V / 500 W at 24 V 1000 W / VA at 48 V 250 V / 500 W at 24 V 250 V DC 5 A continuous, 30 A for 0.5 s
50 ms at V > 110 V DC 20 ms at V > 24 V DC 115 / 230 V 92 - 132 V / 184 - 265 V 7SJ640 7SJ641 7SJ645 7SJ642 Approx. 7 W Approx. 12 W 9W 19 W 12 W 23 W 7SJ647 16 W 33 W
5/202
Technical data
Electrical tests Specification Standards IEC 60255 ANSI C37.90, C37.90.1, C37.90.2, UL508 IEC 60255-5; ANSI/IEEE C37.90.0 2.5 kV (r.m.s. value), 50/60 Hz Radiated electromagnetic interference ANSI/IEEE C37.90.2 Damped wave IEC 60694 / IEC 61000-4-12 35 V/m; 25 to 1000 MHz; amplitude and pulse-modulated 2.5 kV (peak value, polarity alternating) 100 kHz, 1 MHz, 10 and 50 MHz, Ri = 200 EN 50081-* (generic specification) 150 kHz to 30 MHz Limit class B 30 to 1000 MHz Limit class B
Insulation tests Standards Voltage test (100 % test) all circuits except for auxiliary voltage and RS485/RS232 and time synchronization Auxiliary voltage Communication ports and time synchronization Impulse voltage test (type test) all circuits, except communication ports and time synchronization, class III Standards
EMC tests for interference emission; type tests Standard Conducted interferences only auxiliary voltage IEC/CISPR 22
3.5 kV DC 500 V AC 5 kV (peak value); 1.2/50 s; 0.5 J 3 positive and 3 negative impulses at intervals of 5 s
Radio interference field strength IEC/CISPR 11 Units with a detached operator panel must be installed in a metal cubicle to maintain limit class B Mechanical stress tests
EMC tests for interference immunity; type tests IEC 60255-6; IEC 60255-22 (product standard) EN 50082-2 (generic specification) DIN 57435 Part 303 2.5 kV (peak value); 1 MHz; =15 ms; 400 surges per s; test duration 2 s 8 kV contact discharge; 15 kV air gap discharge; both polarities; 150 pF; Ri = 330 10 V/m; 27 to 500 MHz
Vibration, shock stress and seismic vibration During operation Standards Vibration IEC 60255-21-1, class 2 IEC 60068-2-6 IEC 60255-21 and IEC 60068-2 Sinusoidal 10 to 60 Hz; +/- 0.075 mm amplitude; 60 to 150 Hz; 1 g acceleration frequency sweep 1 octave/min 20 cycles in 3 perpendicular axes Semi-sinusoidal Acceleration 5 g, duration 11 ms; 3 shocks in both directions of 3 axes Sinusoidal 1 to 8 Hz: 3.5 mm amplitude (horizontal axis) 1 to 8 Hz: 1.5 mm amplitude (vertical axis) 8 to 35 Hz: 1 g acceleration (horizontal axis) 8 to 35 Hz: 0.5 g acceleration (vertical axis) Frequency sweep 1 octave/min 1 cycle in 3 perpendicular axes IEC 60255-21 and IEC 60068-2 Sinusoidal 5 to 8 Hz: 7.5 mm amplitude; 8 to 150 Hz; 2 g acceleration, frequency sweep 1 octave/min 20 cycles in 3 perpendicular axes Semi-sinusoidal Acceleration 15 g, duration 11 ms 3 shocks in both directions of 3 axes Semi-sinusoidal Acceleration 10 g, duration 16 ms 1000 shocks in both directions of 3 axes
High-frequency test IEC 60255-22-1, class III and VDE 0435 Part 303, class III Electrostatic discharge IEC 60255-22-2 class IV and EN 61000-4-2, class IV Irradiation with radio-frequency field, non-modulated IEC 60255-22-3 (Report) class III Irradiation with radio-frequency field, amplitude-modulated IEC 61000-4-3; class III Irradiation with radio-frequency field, pulse-modulated IEC 61000-4-3/ENV 50204; class III Fast transient interference/burst IEC 60255-22-4 and IEC 61000-4-4, class IV High-energy surge voltages (Surge) IEC 61000-4-5; class III Auxiliary voltage Binary inputs/outputs Line-conducted HF, amplitude-modulated IEC 61000-4-6, class III Power frequency magnetic field IEC 61000-4-8, class IV IEC 60255-6 Oscillatory surge withstand capability ANSI/IEEE C37.90.1 Fast transient surge withstand capability ANSI/IEEE C37.90.1
Shock IEC 60255-21-2, class 1 IEC 60068-2-27 Seismic vibration IEC 60255-21-3, class 1 IEC 60068-3-3
10 V/m, 80 to 1000 MHz; AM 80 %; 1 kHz 10 V/m, 900 MHz; repetition rate 200 Hz, on duration 50 % 4 kV; 5/50 ns; 5 kHz; burst length = 15 ms; repetition rate 300 ms; both polarities; Ri = 50 ; test duration 1 min
From circuit to circuit: 2 kV; 12 ; 9 F across contacts: 1 kV; 2 ;18 F From circuit to circuit: 2 kV; 42 ; 0.5 F across contacts: 1 kV; 42 ; 0.5 F 10 V; 150 kHz to 80 MHz; AM 80 %; 1 kHz 30 A/m; 50 Hz, continuous 300 A/m; 50 Hz, 3 s 0.5 mT, 50 Hz 2.5 to 3 kV (peak value), 1 to 1.5 MHz damped wave; 50 surges per s; duration 2 s, Ri = 150 to 200 4 to 5 kV; 10/150 ns; 50 surges per s both polarities; duration 2 s, Ri = 80
Shock IEC 60255-21-2, Class 1 IEC 60068-2-27 Continuous shock IEC 60255-21-2, class 1 IEC 60068-2-29
5/203
Technical data
Climatic stress tests Temperatures Type-tested acc. to IEC 60068-2-1 and -2, test Bd, for 16 h Temporarily permissible operating temperature, tested for 96 h -25 C to +85 C /-13 F to +185 F -20 C to +70 C /-4 F to -158 F Serial interfaces Operating interface (front of unit) Connection Transmission rate Non-isolated, RS232; front panel, 9-pin subminiature connector Factory setting 115200 baud, min. 4800 baud, max. 115200 baud Port C: DIGSI 4/modem/RTD-box Factory setting 38400 baud, min. 4800 baud, max. 115200 baud
Recommended permanent operat-5 C to +55 C /+25 F to +131 F ing temperature acc. to IEC 60255-6 (Legibility of display may be impaired above +55 C /+131 F) Limiting temperature during -25 C to +55 C /-13 F to +131 F permanent storage Limiting temperature during -25 C to +70 C /-13 F to +158 F transport Humidity Permissible humidity It is recommended to arrange the units in such a way that they are not exposed to direct sunlight or pronounced temperature changes that could cause condensation. Unit design Type Housing Dimensions Weight in kg Surface-mounting housing Flush-mounting housing Housing for detached operator panel Detached operator panel Degree of protection acc. to EN 60529 Surface-mounting housing Flush-mounting housing Operator safety 7SJ640 7SJ642 7XP20 See dimension drawings, part 16 of this catalog Housing width 1/3 8 5 Housing width 1/2 11 6 8 2.5 Housing width 1/1 15 10 12 2.5 7SJ641 7SJ645 7SJ647 Annual average 75 % relative humidity; on 56 days a year up to 95 % relative humidity; condensation not permissible!
Service/modem interface (rear of unit) Isolated interface for data transfer Transmission rate RS232/RS485 Connection For flush-mounting housing/ surface-mounting housing with detached operator panel For surface-mounting housing with two-tier terminal at the top/bottom part Distance RS232 Distance RS485 Test voltage Additional interface (rear of unit) Isolated interface for data transfer Transmission rate RS485 Connection For flush-mounting housing/ surface-mounting housing with detached operator panel For surface-mounting housing with two-tier terminal at the top/bottom part Distance Test voltage Fiber optic Connection fiber-optic cable For flush-mounting housing/ surface-mounting housing with detached operator panel For surface-mounting housing with two-tier terminal at the top/bottom part Optical wavelength Permissible path attenuation Distance Integrated ST connector for fiberoptic connection Mounting location D 9-pin subminiature connector, mounting location D At the bottom part of the housing: shielded data cable Max. 1 km/3300 ft 500 V AC against earth Port D: RTD-box Factory setting 38400 baud, min. 4800 baud, max. 115200 baud 9-pin subminiature connector, mounting location C At the bottom part of the housing: shielded data cable 15 m /49.2 ft Max. 1 km/3300 ft 500 V AC against earth
820 nm Max. 8 dB, for glass fiber 62.5/125 m Max. 1.5 km/0.9 miles
5/204
Technical data
System interface (rear of unit) IEC 60870-5-103 protocol Isolated interface for data transfer to a control center Transmission rate RS232/RS485 Connection For flush-mounting housing/ surface-mounting housing with detached operator panel For surface-mounting housing with two-tier terminal on the top/bottom part Distance RS232 Distance RS485 Test voltage Fiber optic Connection fiber-optic cable For flush-mounting housing/ surface-mounting housing with detached operator panel For surface-mounting housing with two-tier terminal on the top/bottom part Optical wavelength Permissible path attenuation Distance RS485 Connection For flush-mounting housing/ surface-mounting housing with detached operator panel For surface-mounting housing with two-tier terminal on the top/bottom part Distance RS485 Test voltage IEC 61850 protocol Isolated interface for data transfer: - to a control center - with DIGSI - between SIPROTEC 4 relays Transmission rate Ethernet, electrical Connection For flush-mounting housing/ surface-mounting housing with detached operator panel Distance Test voltage Ethernet, optical Connection For flush-mounting housing/ surface-mounting housing with detached operator panel Optical wavelength Distance Intergr. ST connector for FO connection Mounting location "B" Two RJ45 connectors Mounting location "B" Port B, 100 Base T acc. to IEEE802.3 Test voltage Fiber-optic 100 Mbit Connection fiber-optic cable For flush-mounting housing/ surface-mounting housing with detached operator panel For surface-mounting housing with two-tier terminal at the top/bottom part Optical wavelength Permissible path attenuation Distance Integrated ST connector for fiber-optic connection Mounting location B Mounting location B Integrated ST connector for fiberoptic connection Mounting location B Mounting location B Port B Factory setting 9600 baud, min. 1200 baud, max. 115200 baud PROFIBUS-FMS/DP Isolated interface for data transfer to a control center Transmission rate RS485 Connection For flush-mounting housing/ surface-mounting housing with detached operator panel For surface-mounting housing with two-tier terminal on the top/bottom part Distance 9-pin subminiature connector, mounting location B At the bottom part of the housing: shielded data cable 1000 m/3300 ft 93.75 kbaud; 500 m/1500 ft 187.5 kbaud; 200 m/600 ft 1.5 Mbaud; 100 m/300 ft 12 Mbaud 500 V AC against earth Integr. ST connector for FO connection, mounting location B Port B Up to 1.5 Mbaud
At the bottom part of the housing: shielded data cable Max. 15 m/49 ft Max. 1 km/3300 ft 500 V AC against earth
Test voltage Fiber optic Connection fiber-optic cable For flush-mounting housing/ surface-mounting housing with detached operator panel For surface-mounting housing with two-tier terminal on the top/bottom part Optical wavelength Permissible path attenuation Distance MODBUS RTU, ASCII, DNP 3.0 Isolated interface for data transfer to a control center Transmission rate RS485 Connection For flush-mounting housing/ surface-mounting housing with detached operator panel For surface-mounting housing with two-tier terminal at the top/bottom part Distance
At the bottom part of the housing Important: Please refer to footnotes 1) and 2) on page 5/215 820 nm Max. 8 dB, for glass fiber 62.5/125 m 500 kB/s 1.6 km/0.99 miles 1500 kB/s 530 m/0.33 miles Port B Up to 19200 baud
820 nm Max. 8 dB, for glass fiber 62.5/125 m Max. 1.5 km/0.9 miles
(not available)
9-pin subminiature connector, mounting location B At bottom part of the housing: shielded data cable Max. 1 km/3300 ft max. 32 units recommended 500 V AC against earth
At the bottom part of the housing Important: Please refer to footnotes 1) and 2) on page 5/215 820 nm Max 8 dB. for glass fiber 62.5/125 m Max. 1.5 km/0.9 miles
5/205
Technical data
Time synchronization DCF77/IRIG-B signal (Format IRIG-B000) Connection 9-pin subminiature connector (SUB-D) (terminal with surface-mounting housing) 5 V, 12 V or 24 V (optional) Tolerances Pickup/dropout thresholds Ip, IEp Pickup time for 2 I/Ip 20 Dropout ratio for 0.05 I/Ip 0.9 Direction detection For phase faults Polarization With cross-polarized voltages; With voltage memory for measurement voltages that are too low Vref,rot 86 - 180 to 180 (in steps of 1) For one and two-phase faults unlimited; For three-phase faults dynamically unlimited; Steady-state approx. 7 V phase-to-phase With zero-sequence quantities 3V0, 3I0 or with negative-sequence quantities 3V2, 3I2 Vref,rot 86 - 180 to 180 (in steps of 1) VE 2.5 V displacement voltage, measured; 3V0 5 V displacement voltage, calculated 3V2 5 V negative-sequence voltage; 3I2 225 mA negative-sequence current 1) 2 % of setting value or 50 mA1) 5 % of reference (calculated) value + 2 % current tolerance, respectively 30 ms 5 % of reference (calculated) value + 2 % current tolerance, respectively 30 ms
Definite-time overcurrent protection, directional/non-directional (ANSI 50, 50N, 67, 67N) Operating mode non-directional phase protection (ANSI 50) Number of elements (stages) Setting ranges Pickup phase elements Pickup earth elements Delay times T Dropout delay time TDO Times Pickup times (without inrush restraint, with inrush restraint + 10 ms) With twice the setting value With five times the setting value Dropout times Dropout ratio Tolerances Pickup Delay times T, TDO Non-directional Approx. 30 ms Approx. 20 ms Approx. 40 ms Approx. 0.95 for I/Inom 0.3 2 % of setting value or 50 mA 1 % or 10 ms
1)
3-phase (standard) or 2-phase (L1 and L3) I>, I>>, I>>> (phases) IE>, IE>>, IE>>> (earth) 0.5 to 175 A or 1) (in steps of 0.01 A) 0.25 to 175 A or 1) (in steps of 0.01 A) 0 to 60 s or (in steps of 0.01 s) 0 to 60 s (in steps of 0.01 s)
Forward range Rotation of reference voltage Vref,rot Direction sensitivity Zero-sequence quantities 3V0, 3I0
Inverse-time overcurrent protection, directional/non-directional (ANSI 51, 51N, 67, 67N) Operating mode non-directional phase protection (ANSI 51) Setting ranges Pickup phase element IP Pickup earth element IEP Time multiplier T (IEC characteristics) Time multiplier D (ANSI characteristics) Undervoltage threshold V< for release Ip Trip characteristics IEC ANSI 3-phase (standard) or 2-phase (L1 and L3) 0.5 to 20 A or (in steps of 0.01 A) 0.25 to 20 A or 1) (in steps of 0.01 A) 0.05 to 3.2 s or (in steps of 0.01 s)
1)
Tolerances (phase angle error under reference conditions) For phase and earth faults Inrush blocking Influenced functions Lower function limit phases
3 electrical Time-overcurrent elements, I>, IE>, Ip, IEp (directional, non-directional) At least one phase current (50 Hz and 100 Hz) 125 mA1) Earth current (50 Hz and 100 Hz) 125 mA1) 1.5 to 125 A 1) (in steps of 0.01 A) 10 to 45 % (in steps of 1 %) ON/OFF Directional and non-directional pickup, tripping time Current criteria, CB position via aux. contacts, binary input, auto-reclosure ready 3 timers Current threshold (reset on dropping below threshold; monitoring with timer)
Lower function limit earth Normal inverse, very inverse, extremely inverse, long inverse Inverse, short inverse, long inverse moderately inverse, very inverse, extremely inverse, definite inverse Defined by a maximum of 20 value pairs of current and time delay Approx. 1.05 setting value Ip for Ip/Inom 0.3, corresponds to approx. 0.95 pickup threshold Approx. 0.90 setting value Ip Upper function limit (setting range) Setting range I2f /I Crossblock (IL1, IL2, IL3) Dynamic setting change Controllable function Start criteria
5/206
Technical data
(Sensitive) earth-fault detection (ANSI 64, 50 Ns, 51Ns, 67Ns) Displacement voltage starting for all types of earth fault (ANSI 64) Setting ranges Pickup threshold VE> (measured) Pickup threshold 3V0> (calculated) Delay time TDelay pickup Additional trip delay TVDELAY Times Pickup time Dropout ratio Tolerances Pickup threshold VE (measured) Pickup threshold 3V0 (calculated) Delay times Measuring principle Setting ranges Vph min (earth-fault phase) Vph max (unfaulted phases) Measuring tolerance acc. to DIN 57435 part 303 1.8 to 200 V (in steps of 0.1 V) 10 to 225 V (in steps of 0.1 V) 0.04 to 320 s or (in steps of 0.01 s) 0.1 to 40000 s or (in steps of 0.01 s) Approx. 50 ms 0.95 or (pickup value -0.6 V) 3 % of setting value or 0.3 V 3 % of setting value or 3 V 1 % of setting value or 10 ms Voltage measurement (phase-to-earth) 10 to 100 V (in steps of 1 V) 10 to 100 V (in steps of 1 V) 3 % of setting value, or 1 V Logarithmic inverse Logarithmic inverse with knee point Measuring method cos /sin Direction measurement Measuring principle Setting ranges Measuring enable IRelease direct. For sensitive input For normal input Direction phasor Correction Dropout delay TReset delay Tolerances Pickup measuring enable For sensitive input For normal input Angle tolerance Measuring method (V0/I0) Direction measurement Minimum voltage Vmin. measured Minimum voltage Vmin. calculated Phase angle Delta phase angle Tolerances Pickup threshold VE (measured) Pickup threshold 3 V0 (calculated) Angle tolerance Angle correction for cable CT Approx. 50 ms Approx. 0.95 Angle correction F1, F2 Current value I1, I2 For sensitive input For normal input 0 to 5 (in steps of 0.1) 0.001 to 1.5 A (in steps of 0.001 A) 0.25 to 175 A1) (in steps of 0.01 A) IE and VE measured or 3I0 and 3V0 calculated 0.4 to 50 V (in steps of 0.1 V) 10 to 90 V (in steps of 1 V) -180 to 180 (in steps of 0.1) 0 to 180 (in steps of 0.1) 3 % of setting value or 0.3 V 3 % of setting value or 3 V 3 IE and VE measured or 3I0 and 3V0 calculated Active/reactive power measurement Delay times in linear range 7 % of reference value for 2 I/IEEp 20 + 2 % current tolerance, or 70 ms Refer to the manual Refer to the manual
0.001 to 1.2 A (in steps of 0.001 A) 0.25 to 150 A1) (in steps of 0.01 A) - 45 to + 45 (in steps of 0.1 ) 1 to 60 s (in steps of 1 s)
Earth-fault pickup for all types of earth faults Definite-time characteristic (ANSI 50Ns) Setting ranges Pickup threshold IEE>, IEE>> For sensitive input 0.001 to 1.5 A (in steps of 0.001 A) For normal input 0.25 to 175 A1) (in steps of 0.01 A) Delay times T for IEE>, IEE>> 0 to 320 s or (in steps of 0.01 s) 0 to 60 s (in steps of 0.01 s) Dropout delay time TDO Times Pickup times Dropout ratio Tolerances Pickup threshold For sensitive input For normal input Delay times
High-impedance restricted earth-fault protection (ANSI 87N) / single-phase overcurrent protection Setting ranges Pickup thresholds I>, I>> For sensitive input For normal input Delay times TI>, TI>> Times Pickup times Minimum Typical Dropout times Dropout ratio Tolerances Pickup thresholds
Earth-fault pickup for all types of earth faults Inverse-time characteristic (ANSI 51Ns) User-defined characteristic Defined by a maximum of 20 pairs of current and delay time values Setting ranges Pickup threshold IEEp For sensitive input For normal input User defined Time multiplier T Times Pickup times Pickup threshold Dropout ratio Tolerances Pickup threshold For sensitive input For normal input
0.003 to 1.5 A or (in steps of 0.001 A) 0.25 to 175 A1) or (in steps of 0.01 A) 0 to 60 s or (in steps of 0.01 s)
0.001 A to 1.4 A (in steps of 0.001 A) 0.25 to 20 A1) (in steps of 0.01 A) 0.1 to 4 s or (in steps of 0.01 s) Approx. 50 ms Approx. 1.1 IEEp Approx. 1.05 IEEp
Approx. 20 ms Approx. 30 ms Approx. 30 ms Approx. 0.95 for I/Inom 0.5 3 % of setting value or 1 % rated current at Inom = 1 or 5 A; 5 % of setting value or 3 % rated current at Inom = 0.1 A 1 % of setting value or 10 ms
Note: Due to the high sensitivity the linear range of the measuring input IN with integrated sensitive input transformer is from 0.001 A to 1.6 A. For currents greater than 1.6 A, correct directionality can no longer be guaranteed. 1) For Inom = 1 A, all limits divided by 5.
5/207
Technical data
Intermittent earth-fault protection Setting ranges Pickup threshold For IE For 3I0 For IEE Pickup prolongation time Earth-fault accumulation time Reset time for accumulation Number of pickups for intermittent earth fault IIE> IIE> IIE> TV Tsum Tres 0.25 to 175 A1) (in steps of 0.01 A) 0.25 to 175 A1) (in steps of 0.01 A) 0.005 to 1.5 A (in steps of 0.001 A) 0 to 10 s (in steps of 0.01 s) 0 to 100 s (in steps of 0.01 s) 1 to 600 s (in steps of 1 s) 2 to 10 (in steps of 1) Program for earth fault Start-up by Time-overcurrent elements (dir., non-dir.), sensitive earth-fault protection, binary input Pickup of protection functions, three-phase fault detected by a protective element, binary input, last TRIP command after the reclosing cycle is complete (unsuccessful reclosing), TRIP command by the breaker failure protection (50BF), opening the CB without ARC initiation, external CLOSE command
Blocking of ARC
Times Pickup times Current = 1.25 pickup value Approx. 30 ms Current 2 pickup value Approx. 22 ms Dropout time Tolerances Pickup threshold IIE> Times TV, Tsum, Tres Setting ranges Factor k Time constant Warning overtemperature alarm/trip Current warning stage Ialarm 0.1 to 4 (in steps of 0.01) 1 to 999.9 min (in steps of 0.1 min) 50 to 100 % with reference to the tripping overtemperature (in steps of 1 %) 0.5 to 20 A (in steps of 0.01 A) Approx. 22 ms 3 % of setting value, or 50 mA1) 1 % of setting value or 10 ms
Setting ranges Dead time 0.01 to 320 s (in steps of 0.01 s) (separate for phase and earth and individual for shots 1 to 4) Blocking duration for manual- 0.5 s to 320 s or 0 (in steps of 0.01 s) CLOSE detection Blocking duration after 0.5 s to 320 s (in steps of 0.01 s) reclosure Blocking duration after 0.01 to 320 s (in steps of 0.01 s) dynamic blocking Start-signal monitoring time Circuit-breaker supervision time Max. delay of dead-time start Action time 0.01 to 320 s or (in steps of 0.01 s) 0.1 to 320 s (in steps of 0.01 s) 0 to 1800 s or (in steps of 0.1 s) 0.01 to 320 s or (in steps of 0.01 s)
Maximum dead time extension 0.5 to 320 s or (in steps of 0.01 s) The delay times of the following protection function can be altered individually by the ARC for shots 1 to 4 (setting value T = T, non-delayed T = 0, blocking T = ): I>>>, I>>, I>, Ip, Idir>>, Idir>, Ipdir IE>>>, IE>>, IE>, IEp, IEdir>>, IEdir>, IEdir Additional functions
2
Extension factor when stopped 1 to 10 with reference to the time conk factor stant with the machine running (in steps of 0.1) Rated overtemperature (for Inom) 40 to 200 C (in steps of 1 C) Tripping characteristic For (I/k Inom) 8
t = th ln
t th I Ipre k
Tripping time Temperature rise time constant Load current Preload current Setting factor acc. to VDE 0435 Part 3011 and IEC 60255-8 Inom = Rated (nominal) current of the protection relay
= = = = =
Lockout (final trip), delay of dead-time start via binary input (monitored), dead-time extension via binary input (monitored), co-ordination with other protection relays, circuit-breaker monitoring, evaluation of the CB contacts
Breaker failure protection (ANSI 50 BF) Setting ranges Pickup thresholds Delay time Times Pickup times with internal start with external start Dropout times Tolerances Pickup value Delay time Operating modes Additional release conditions 0.2 to 5 A1) (in steps of 0.01 A) 0.06 to 60 s or (in steps of 0.01 s)
is contained in the delay time is contained in the delay time Approx. 25 ms 2 % of setting value (50 mA)1) 1 % or 20 ms Synchro-check Asynchronous/synchronous Live-bus / dead line Dead-bus / live-line Dead-bus and dead-line Bypassing
Tolerances With reference to k Inom Class 5 acc. to IEC 60255-8 With reference to tripping time 5 % +/- 2 s acc. to IEC 60255-8 Auto-reclosure (ANSI 79) Number of reclosures Program for phase fault Start-up by 0 to 9 Shot 1 to 4 individually adjustable Time-overcurrent elements (dir., non-dir.), negative sequence, binary input
5/208
Technical data
Voltages Max. operating voltage Vmax Min. operating voltage Vmin 20 to 140 V (phase-to-phase) (in steps of 1 V) 20 to 125 V (phase-to-phase) (in steps of 1 V) Negative-sequence current detection (ANSI 46) Definite-time characteristic (ANSI 46-1 and 46-2) Setting ranges Pickup current I2>, I2>> Delay times Dropout delay time TDO Functional limit Times Pickup times Dropout times Dropout ratio Tolerances Pickup thresholds Delay times Setting ranges Pickup current Time multiplier T (IEC characteristics) Time multiplier D (ANSI characteristics) Functional limit 2 to 80 (in steps of 1 ) 2 5 for f 1 Hz 10 for f > 1 Hz 0.01 to 0.6 s (in steps of 0.01 s) 0.01 to 0.04 Hz (in steps of 0.01 Hz) Trip characteristics IEC ANSI Pickup threshold Dropout IEC and ANSI (without disk emulation) ANSI with disk emulation Tolerances Pickup threshold Time for 2 M 20 0.5 to 15 A or (in steps of 0.01 A) 0 to 60 s or (in steps of 0.01 s) 0 to 60 s (in steps of 0.01 s) All phase currents 50 A1) Approx. 35 ms Approx. 35 ms Approx. 0.95 for I2 /Inom > 0.3 3 % of the setting value or 50 mA1) 1 % or 10 ms
V< for dead-line / dead-bus 1 to 60 V (phase-to-phase) check (in steps of 1 V) V> for live-line / live-bus check 20 to 140 V (phase-to-phase) (in steps of 1 V) Primary rated voltage of transformer V2nom Tolerances Drop-off to pickup ratios V-measurement Voltage difference Tolerance f-measurement f-measurement (f2>f1; f2<f1) 0.01 to 2 Hz (in steps of 0.01 Hz) Tolerance 15 mHz -measurement -measurement (2>1; 2>1) Tolerance Max. phase displacement Circuit-breaker operating time CB operating time Threshold ASYN SYN Threshold synchronous / asynchronous Adaptation Vector group adaptation by angle 0 to 360 (in steps of 1 ) Different voltage 0.5 to 2 (in steps of 0.01) transformers V1/V2 Times Minimum measuring time Approx. 80 ms Max. duration TSYN DURATION 0.01 to 1200 s; (in steps of 0.01 s) Supervision time TSUP VOLTAGE 0 to 60 s (in steps of 0.01 s) Closing time of CB TCB close Tolerance of all timers Reference voltage V1 Range Tolerance*) Voltage to be synchronized V2 Range Tolerance*) Frequency of V1 and V2 Range Tolerance*) Voltage difference (V2 V1) Range Tolerance*) Frequency difference (f2 f1) Range Tolerance*) Angle difference (2 1) Range Tolerance*) 0 to 60 s (in steps of 0.01 s) 1 % of setting value or 10 ms In kV primary, in V secondary or in % Vnom 10 to 120 % Vnom 1 % of measured value or 0.5 % of Vnom In kV primary, in V secondary or in % Vnom 10 to 120 % Vnom 1 % of measured value or 0.5 % of Vnom f1, f2 in Hz fN 5 Hz 20 mHz In kV primary, in V secondary or in % Vnom 10 to 120 % Vnom 1 % of measured value or 0.5 % of Vnom In mHz fN 5 Hz 20 mHz In 0 to 180 0.5 0.5 to 50 V (phase-to-phase) (in steps of 1 V) 1V 0.1 to 800 kV (in steps of 0.01 kV) 2 % of pickup value or 2 V approx. 0.9 (V>) or 1.1 (V<)
Inverse-time characteristic (ANSI 46-TOC) 0.5 to 10 A1) (in steps of 0.01 A) 0.05 to 3.2 s or (in steps of 0.01 s) 0.5 to 15 s or (in steps of 0.01 s) All phase currents 50 A1) Normal inverse, very inverse, extremely inverse Inverse, moderately inverse, very inverse, extremely inverse Approx. 1.1 I2p setting value Approx. 1.05 I2p setting value, which is approx. 0.95 pickup threshold Approx. 0.90 I2p setting value 3 % of the setting value or 50 mA1) 5 % of setpoint (calculated) +2 % current tolerance, at least 30 ms
Flexible protection functions (ANSI 27, 32, 47, 50, 55, 59, 81R) Operating modes / measuring quantities 3-phase 1-phase Without fixed phase relation Pickup when Setting ranges Current I, I1, I2, 3I0, IE Current ratio I2/I1 Sens. earth curr. IE sens. Voltages V, V1, V2, 3V0 Displacement voltage VE Power P, Q Power factor (cos ) Frequency
I, I1, I2, I2/I1, 3I0, V, V1, V2, 3V0, P, Q, cos I, IE, IE sens., V, VE, P, Q, cos f, df/dt, binary input Exceeding or falling below threshold value 0.15 to 200 A1) (in steps of 0.01 A) 15 to 100 % (in steps of 1 %) 0.001 to 1.5 A (in steps of 0.001 A) 1 to 260 V (in steps of 0.1 V) 1 to 200 V (in steps of 0.1 V) 0.5 to 10000 W (in steps of 0.1 W) - 0.99 to + 0.99 (in steps of 0.01)
40 to 60 Hz (in steps of 0.01 Hz) fN = 50 Hz 50 to 70 Hz (in steps of 0.01 Hz) fN = 60 Hz Rate-of-frequency change df/dt 0.1 to 20 Hz/s (in steps of 0.01 Hz/s) Dropout ratio >- stage Dropout ratio <- stage Dropout differential f Pickup delay time Trip delay time Dropout delay time *) With rated frequency. 1) At Inom = 1 A, all limits divided by 5. 1.01 to 3 (in steps of 0.01) 0.7 to 0.99 (in steps of 0.01) 0.02 to 1.00 Hz (in steps of 0.01 Hz) 0 to 60 s (in steps of 0.01 s) 0 to 3600 s (in steps of 0.01 s) 0 to 60 s (in steps of 0.01 s)
5/209
Technical data
Flexible protection functions (ANSI 27, 32, 47, 50, 55, 59, 81R) (cont'd) Times Pickup times Current, voltage (phase quantities) With 2 times the setting value With 10 times the setting value Current, voltages (symmetrical components) With 2 times the setting value With 10 times the setting value Power Typical Maximum (low signals and thresholds) Power factor Frequency Rate-of-frequency change with 1.25 times the setting value Binary input Dropout times Current, voltage (phase quantities) Current, voltages (symmetrical components) Power Typical Maximum Power factor Frequency Rate-of-frequency change Binary input Tolerances Pickup threshold Current Current (symmetrical components) Voltage Voltage (symmetrical components) Power Power factor Frequency Rate-of-frequency change Times Setting ranges Motor starting current ISTARTUP Pickup threshold IMOTOR START Permissible starting time TSTARTUP , COLD MOTOR Permissible starting time TSTARTUP, WARM MOTOR Temperature threshold cold motor Permissible blocked rotor time TBLOCKED-ROTOR Tripping time characteristic for I > IMOTOR START Dropout ratio IMOTOR START Tolerances Pickup threshold Delay time Approx. 0.95 2 % of setting value or 50 mA1) 5 % or 30 ms
Approx. 30 ms Approx. 20 ms
Load jam protection for motors (ANSI 51M) Setting ranges Current threshold for alarm and trip Delay times Blocking duration after CLOSE signal detection Tolerances Pickup threshold Delay time Setting ranges Motor starting current relative to rated motor current IMOTOR START/IMotor Nom Rated motor current IMotor Nom Max. permissible starting time TStart Max Equilibrium time TEqual Minimum inhibit time TMIN. INHIBIT TIME Max. permissible number of warm starts Difference between cold and warm starts Extension k-factor for cooling simulations of rotor at zero speed k at STOP Extension factor for cooling time constant with motor running k RUNNING Restarting limit restart = rot max perm restart 1.1 to 10 (in steps of 0.1) 1 to 6 A1) (in steps of 0.01 A) 1 to 320 s (in steps of 1 s) 0 to 320 min (in steps of 0.1 min) 0.2 to 120 min (in steps of 0.1 min) 1 to 4 (in steps of 1) 1 to 2 (in steps of 1) 0.2 to 100 (in steps of 0.1)
Approx. 40 ms Approx. 30 ms Approx. 120 ms Approx. 350 ms 300 to 600 ms Approx. 100 ms Approx. 220 ms Approx. 20 ms < 20 ms < 30 ms
0.25 to 60 A1) (in steps of 0.01 A) 0 to 600 s (in steps of 0.01 s) 0 to 600 s (in steps of 0.01 s) 2 % of setting value or 50 mA1) 1 % of setting value or 10 ms
< 50 ms < 350 ms < 300 ms < 100 ms < 200 ms < 10 ms
1 % of setting value or 50 mA1) 2 % of setting value or 100 mA1) 1 % of setting value or 0.1 V 2 % of setting value or 0.2 V 1 % of setting value or 0.3 W 2 degrees 10 mHz 5 % of setting value or 0.05 Hz/s 1 % of setting value or 10 ms
nc 1 nc
Starting time monitoring for motors (ANSI 48) 2.5 to 80 A1) (in steps of 0.01) 2 to 50 A1) (in steps of 0.01) 1 to 180 s (in steps of 0.1 s) 0.5 to 180 s (in steps of 0.1 s) 0 to 80 % (in steps of 1 %) 0.5 to 120 s or (in steps of 0.1 s) I t = STARTUP TSTARTUP I ISTARTUP = Rated motor starting current I = Actual current flowing TSTARTUP = Tripping time for rated motor starting current t = Tripping time in seconds 1) At Inom = 1 A, all limits divided by 5.
2
= Temperature limit below which restarting is possible rot max perm = Maximum permissible rotor overtemperature (= 100 % in operational measured value rot/rot trip) nc = Number of permissible start-ups from cold state
Undercurrent monitoring (ANSI 37) Signal from the operational measured values Predefined with programmable logic
5/210
Technical data
Temperature monitoring box (ANSI 38) Temperature detectors Connectable boxes Number of temperature detectors per box Type of measuring Mounting identification Thresholds for indications For each measuring detector Stage 1 1 or 2 Max. 6 Pt 100 or Ni 100 or Ni 120 Oil or Environment or Stator or Bearing or Other Frequency protection (ANSI 81) Number of frequency elements 4 Setting ranges Pickup thresholds for fnom = 50 Hz 40 to 60 Hz (in steps of 0.01 Hz) Pickup thresholds for fnom = 60 Hz 50 to 70 Hz (in steps of 0.01 Hz) Dropout differential 0.02 Hz to 1.00 Hz (in steps of 0.01 Hz) = |pickup threshold - dropout threshold| Delay times 0 to 100 s or (in steps of 0.01 s) Undervoltage blocking, with 10 to 150 V (in steps of 1 V) positive-sequence voltage V1 Times Pickup times Approx. 80 ms Dropout times Approx. 75 ms Dropout Ratio undervoltage blocking Tolerances Pickup thresholds Frequency Undervoltage blocking Delay times Fault locator (ANSI 21FL) Output of the fault distance In primary or secondary, in km / miles of line length, in % of line length Trip command, dropout of a protection element, via binary input 0.001 to 1.9 /km2) (in steps of 0.0001) 0.001 to 3 /mile2) (in steps of 0.0001) Approx. 1.05
Stage 2
-50 C to 250 C (in steps of 1 C) -58 F to 482 F (in steps of 1 F) or (no indication) -50 C to 250 C (in steps of 1 C) -58 F to 482 F (in steps of 1 F) or (no indication)
Undervoltage protection (ANSI 27) Operating modes/measuring quantities 3-phase Positive phase-sequence voltage or phase-to-phase voltages or phase-to-earth voltages Single-phase phase-earth or phase-phase voltage
1-phase Setting ranges Pickup thresholds V<, V<< dependent on voltage connection and chosen measuring quantity Dropout ratio r Delay times T Current Criteria "Bkr Closed IMIN" Times Pickup times Dropout times Tolerances Pickup thresholds Times Overvoltage protection (ANSI 59)
10 to 120 V (in steps of 1 V) 10 to 210 V (in steps of 1 V) 1.01 to 3 (in steps of 0.01) 0 to 100 s or (in steps of 0.01 s) 0.2 to 5 A1) (in steps of 0.01 A)
Tolerances Measurement tolerance acc. to 2.5 % fault location, or 0.025 VDE 0435, Part 303 for sinusoi- (without intermediate infeed) for dal measurement quantities 30 K 90 and VK/Vnom 0.1 and IK/Inom 1 Additional functions Operational measured values Currents In A (kA) primary, IL1, IL2, IL3 in A secondary or in % Inom Positive-sequence component I1 Negative-sequence component I2 IE or 3I0 Range Tolerance3) 10 to 200 % Inom 1 % of measured value or 0.5 % Inom
Operating modes/measuring quantities 3-phase Positive phase-sequence voltage or negative phase-sequence voltage or phase-to-phase voltages or phase-to-earth voltages Single-phase phase-earth or phase-phase voltage
1-phase Setting ranges Pickup thresholds V>, V>> dependent on voltage connection and chosen measuring quantity Dropout ratio r Delay times T Times Pickup times V Pickup times V1, V2 Dropout times Tolerances Pickup thresholds Times
40 to 260 V (in steps of 1 V) 40 to 150 V (in steps of 1 V) 2 to 150 V (in steps of 1 V) 0.9 to 0.99 (in steps of 0.01) 0 to 100 s or (in steps of 0.01 s) Approx. 50 ms Approx. 60 ms As pickup times 3 % of setting value or 1 V 1 % of setting value or 10 ms
Phase-to-earth voltages In kV primary, in V secondary or in % Vnom VL1-E, VL2-E, VL3-E Phase-to-phase voltages VL1-L2, VL2-L3, VL3-L1, VSYN, VE or V0 Positive-sequence component V1 Negative-sequence component V2 Range Tolerance3) S, apparent power Range Tolerance3) 10 to 120 % Vnom 1 % of measured value or 0.5 % of Vnom In kVAr (MVAr or GVAr) primary and in % of Snom 0 to 120 % Snom 1 % of Snom for V/Vnom and I/Inom = 50 to 120 %
1) At Inom = 1 A, all limits divided by 5. 2) At Inom = 1 A, all limits multiplied with 5. 3) At rated frequency.
5/211
Technical data
Operational measured values (cont'd) P, active power Range Tolerance1) With sign, total and phase-segregated in kW (MW or GW) primary and in % Snom 0 to 120 % Snom 1 % of Snom for V/Vnom and I/Inom = 50 to 120 % and cos = 0.707 to 1 with Snom = 3 Vnom I nom With sign, total and phase-segregated in kVAr (MVAr or GVAr)primary and in % Snom 0 to 120 % Snom 1 % of Snom for V/Vnom and I/Inom = 50 to 120 % and sin = 0.707 to 1 with Snom = 3 Vnom I nom Total and phase segregated - 1 to + 1 2 % for cos 0.707 In Hz fnom 5 Hz 20 mHz Max. / Min. report Report of measured values Reset, automatic With date and time Time of day adjustable (in minutes, 0 to 1439 min) Time frame and starting time adjustable (in days, 1 to 365 days, and ) Using binary input, using keypad, via communication IL1, IL2, IL3, I1 (positive-sequence component) VL1-E, VL2-E, VL3-E V1 (positive-sequence component) VL1-L2, VL2-L3, VL3-L1 S, P, Q, cos , frequency /Trip
Reset, manual
Q, reactive power
Range Tolerance1)
Min./Max. values for mean values IL1dmd, IL2dmd, IL3dmd I1 (positive-sequence component); Sdmd, Pdmd, Qdmd Local measured values monitoring Current asymmetry Voltage asymmetry Current phase sequence Voltage phase sequence Limit value monitoring Fuse failure monitor For all types of networks Fault recording Recording of indications of the last 8 power system faults Recording of indications of the last 3 power system ground faults Time stamping Resolution for event log (operational annunciations) Resolution for trip log (fault annunciations) Maximum time deviation (internal clock) Battery 1 ms 1 ms 0.01 % Lithium battery 3 V/1 Ah, type CR 1/2 AA, message Battery Fault for insufficient battery charge With the option of blocking affected protection functions Imax/Imin > balance factor, for I>Ibalance limit Vmax/Vmin > balance factor, for V>Vlim Clockwise (ABC) / counter-clockwise (ACB) Clockwise (ABC) / counter-clockwise (ACB) Predefined limit values, user-defined expansions via CFC
Temperature overload protection In % /Trip Range Tolerance1) Temperature restart inhibit L/L Trip Range Tolerance1) Restart threshold Restart/L Trip Reclose time TReclose Currents of sensitive ground fault detection (total, real, and reactive current) IEE, IEE real, IEE reactive Range Tolerance1) RTD-box Synchronism and voltage check Long-term averages Time window Frequency of updates Long-term averages of currents of real power of reactive power of apparent power 5, 15, 30 or 60 minutes Adjustable IL1dmd, IL2dmd, IL3dmd, I1dmd in A (kA) Pdmd in W (kW, MW) Qdmd in VAr (kVAr, MVAr) Sdmd in VAr (kVAr, MVAr) 0 to 400 % 5 % class accuracy per IEC 60255-8 In % 0 to 400 % 5 % class accuracy per IEC 60255-8 In % In min In A (kA) primary and in mA secondary 0 mA to 1600 mA 2 % of measured value or 1 mA See section Temperature monitoring box See section Synchronism and voltage check
Oscillographic fault recording Maximum 8 fault records saved, memory maintained by buffer battery in case of loss of power supply Recording time Total 20 s Pre-trigger and post-fault recording and memory time adjustable 1 sample/1.25 ms (16 samples/cycle) 1 sample/1.04 ms (16 samples/cycle)
5/212
Technical data
Energy/power Meter values for power in kWh (MWh or GWh) and kVARh Wp, Wq (real and reactive power (MVARh or GVARh) demand) Tolerance1) Statistics Saved number of trips Up to 9 digits Programmable controller Local control Units with small display Units with large display Remote control Number of automatic reclosing Up to 9 digits commands (segregated according to 1st and 2nd cycle) Circuit-breaker wear Methods Ix with x = 1 .. 3 2-point method (remaining service life) i2t Phase-selective accumulation of measured values on TRIP command, up to 8 digits, phase-selective limit values, monitoring indication 0 to 9999 (resolution 1) 0 to 99999 h (resolution 1 h) 0 to 99999 h (resolution 1 h) 0 to 100 % (resolution 0.1 %) See operational measured values Of the last 5 start-ups 0.30 s to 9999.99 s (resolution 10 ms) 0 A to 1000 kA (resolution 1 A) 0 V to 100 kV (resolution 1 V) Up to 7 digits Overshoot of an adjustable current threshold (BkrClosed IMIN) 2 % for I > 0.5 Inom, V > 0.5 Vnom and cos (p.f.) 0.707 Control Number of switching units Interlocking Circuit-breaker signals Control commands Depends on the binary inputs and outputs Programmable Feedback, close, open, intermediate position Single command / double command 1, 1 plus 1 common or 2 trip contacts CFC logic, graphic input tool Control via menu, assignment of a function key Control via menu, control with control keys Via communication interfaces, using a substation automation and control system (e.g. SICAM), DIGSI 4 (e.g. via modem)
Operation
CE conformity This product is in conformity with the Directives of the European Communities on the harmonization of the laws of the Member States relating to electromagnetic compatibility (EMC Council Directive 89/336/EEC) and electrical equipment designed for use within certain voltage limits (Council Directive 73/23/EEC). This unit conforms to the international standard IEC 60255, and the German standard DIN 57435/Part 303 (corresponding to VDE 0435/Part 303). Further applicable standards: ANSI/IEEE C37.90.0 and C37.90.1. The unit conforms to the international standard IEC 60255, and the German standard DIN 57435/Part 303 (corresponding to VDE 0435/Part 303). This conformity is the result of a test that was performed by Siemens AG in accordance with Article 10 of the Council Directive complying with the generic standards EN 50081-2 and EN 50082-2 for the EMC Directive and standard EN 60255-6 for the low-voltage Directive.
Motor statistics Total number of motor start-ups Total operating time Total down-time Ratio operating time/down-time Active energy and reactive energy Motor start-up data: Start-up time Start-up current (primary) Start-up voltage (primary) Operating hours counter Display range Criterion Trip circuit monitoring With one or two binary inputs Commissioning aids Phase rotation field check, operational measured values, circuit-breaker / switching device test, creation of a test measurement report Clock Time synchronization DCF77/IRIG-B signal (telegram format IRIG-B000), binary input, communication 4 (parameter group A, B, C and D) Via keypad, DIGSI, system (SCADA) interface or binary input
Setting group switchover of the function parameters Number of available setting groups Switchover performed
1) At rated frequency.
5/213
Description
Order No.
0 1 2 5 7
1 2 5 6 7
2 4 5
A B C D E F G
Region-specific default settings/function versions and language settings Region DE, 50 Hz, IEC, language: German (language selectable) Region World, 50/60 Hz, IEC/ANSI, language: English (GB) (language selectable) Region US, 60 Hz, ANSI, language: English (US) (language selectable) Region FR, 50/60 Hz, IEC/ANSI, language: French (language selectable) Region World, 50/60 Hz, IEC/ANSI, language: Spanish (language selectable) Region IT, 50/60 Hz, IEC/ANSI, language: Italian (language selectable)
A B C D E F
1) Rated current can be selected by means of jumpers 2) Transition between the two auxiliary voltage ranges can be selected by means of jumpers. 3) The binary input thresholds can be selected per binary input by means of jumpers.
5/214
Description
Order No.
Order code
ooo
PROFIBUS-FMS Slave, 820 nm wavelength, double ring, ST connector 1) PROFIBUS-DP Slave, RS485 PROFIBUS-DP Slave, 820 nm wavelength, double ring, ST connector 1) MODBUS, RS485 MODBUS, 820 nm wavelength, ST connector 2) DNP 3.0, RS485 DNP 3.0, 820 nm wavelength, ST connector
2) 2)
9 9 9
IEC 61850, 100 Mbit Ethernet, electrical, double, RJ45 connector (EN 100) IEC 61850, 100 Mbit Ethernet, optical, double, ST connector (EN 100) 2) Only Port C (service interface) DIGSI 4/modem, electrical RS232 DIGSI 4/modem/RTD-box3), electrical RS485 Port C and D (service and additional interface) Port C (service interface) DIGSI 4/modem, electrical RS232 DIGSI 4/modem/RTD-box3), electrical RS485 Port D (additional interface) RTD-box3), 820 nm fiber, ST connector 4) RTD-box3), electrical RS485 Measuring/fault recording Fault recording Slave pointer, mean values, min/max values, fault recording
oo
1 2
A F
1 3
1) Not with position 9 = B; if 9 = B, please order 7SJ6 unit with RS485 port and separate fiber-optic converters. For single ring, please order converter 6GK1502-2CB10, not available with position 9 = B. For double ring, please order converter 6GK1502-3CB10, not available with position 9 = B. The converter requires a 24 V AC power supply (e.g. power supply 7XV5810-0BA00). 2) Not available with position 9 = B. 3) Temperature monitoring box 7XV5662- AD10, refer to Accessories.
4) When using the RTD-box at an optical interface, the additional RS485 fiber-optic converter 7XV5650-0 A00 is required.
5/215
Description
Order No.
5
n
Control Time-overcurrent protection I>, I>>, I>>>, Ip Earth-fault protection IE>, IE>>, IE>>>, IEp Insensitive earth-fault protection through IEE function: IEE>, IEE>>, IEEp1) Flexible protection functions (index quantities derived from current): Additional time-overcurrent protection stages I2>, I>>>>, IE>>>> Voltage-dependent inverse-time overcurrent protection Overload protection (with 2 time constants) Phase balance current protection (negative-sequence protection) Undercurrent monitoring Phase sequence Displacement voltage Breaker failure protection Trip circuit supervision; 4 setting groups, cold-load pickup; inrush blocking Lockout F A Under-/overvoltage Under-/overfrequency Flexible protection (index quantities derived from current and voltages): Voltage, power, p.f., rate-of-frequency-change protection Under-/overvoltage Under-/overfrequency Flexible protection (index quantities derived from current and voltages): Voltage, power, p.f., rate-of-frequency-change protection Intermittent earth fault Direction determination for overcurrent, phases and earth
F E
PE F C
n n
Dir Dir
67/67N V, P, f 67/67N
n
Directional earth-fault detection
Direction determination for overcurrent, phases and earth 27/59 Under-/overvoltage 81O/U Under-/overfrequency 27/47/59(N) Flexible protection (index quantities derived from 32/55/81R current and voltages): Voltage, power, p.f., rate-of-frequency-change protection Direction determination for overcurrent, phases and earth; intermittent earth fault Direction determination for overcurrent, phases and earth Directional sensitive earth-fault detection High-impedance restricted earth fault Directional sensitive earth-fault detection High-impedance restricted earth fault Under-/overvoltage Under-/overfrequency Flexible protection (index quantities derived from current and voltages): Voltage, power, p.f., rate-of-frequency-change protection Direction determination for overcurrent, phases and earth Directional sensitive earth-fault detection High-impedance restricted earth fault Intermittent earth fault
F G PC
Dir Dir
IEF
67/67N 67/67N 67Ns 87N V, P, f 67Ns 87N 27/59 81O/U 27/47/59(N) 32/55/81R
n n
n Basic version included
F D 2)
F F
2)
Directional earth-fault V, P, f = Voltage, power, frequency detection protection Dir = Directional overcurrent protection IEF = Intermittent earth fault
Dir
IEF
P D 2)
1) Only with insensitive earth-current transformer when position 7 = 1, 5, 7. 2) For isolated/compensated networks only with sensitive earth-current transformer when position 7 = 2, 6.
5/216
Description
Order No.
Control Time-overcurrent protection I>, I>>, I>>>, Ip Earth-fault protection IE>, IE>>, IE>>>, IEp Insensitive earth-fault protection via IEE function: IEE>, IEE>>, IEEp1) Flexible protection functions (index quantities derived from current): Additional time-overcurrent protection stages I2>, I>>>>, IE>>>> Voltage-dependent inverse-time overcurrent protection Overload protection (with 2 time constants) Phase balance current protection (negative-sequence protection) Undercurrent monitoring Phase sequence Displacement voltage Breaker failure protection Trip circuit supervision, 4 setting groups, cold-load pickup, inrush blocking Lockout Directional sensitive earth-fault detection, High-impedance restricted earth fault
n
n
F B 2)
Motor V, P, f 67Ns 87N 48/14 66/86 51M 27/59 81O/U 27/47/59(N) 32/55/81R 67/67N Directional sensitive earth-fault detection, High-impedance restricted earth fault Starting time supervision, locked rotor Restart inhibit Load jam protection, motor statistics Under-/overvoltage Under-/overfrequency Flexible protection (index quantities derived from current and voltages): Voltage, power, p.f., rate-of-frequency-change protection
H F 2)
Motor Dir
V, P, f
Direction determination for overcurrent, phases and earth 67Ns Directional sensitive earth-fault detection 87N High-impedance restricted earth fault 48/14 Starting time supervision, locked rotor 66/86 Restart inhibit 51M Load jam protection, motor statistics 27/59 Under-/overvoltage 81O/U Under-/overfrequency 27/47/59(N) Flexible protection (index quantities derived from 32/55/81R current and voltages): Voltage, power, p.f., rate-of-frequency-change protection Direction determination for overcurrent, phases and earth Directional sensitive earth-fault detection High-impedance restricted earth fault Intermittent earth fault 48/14 Starting time supervision, locked rotor 66/86 Restart inhibit 51M Load jam protection, motor statistics 27/59 Undervoltage/overvoltage 81O/U Underfrequency/overfrequency 27/47/59(N) Flexible protection (index quantities derived from 32/55/81R current and voltages): Voltage, power, p.f., rate-of-frequency-change protection
H H 2)
R H 2)
5/217
Description
Order No.
7SJ64o
Control Time-overcurrent protection I>, I>>, I>>>, Ip Earth-fault protection IE>, IE>>, IE>>>, IEp Insensitive earth-fault protection via IEE function: IEE>, IEE>>, IEEp1) Flexible protection functions (index quantities derived from current): Additional time-overcurrent protection stages I2>, I>>>>, IE>>>> Voltage-dependent inverse-time overcurrent protection Overload protection (with 2 time constants) Phase balance current protection (negative-sequence protection) Undercurrent monitoring Phase sequence Displacement voltage Breaker failure protection Trip circuit supervision 4 setting groups, cold-load pickup Inrush blocking Lockout
Order code
86
Motor Dir
V, P, f 67/67N
Direction determination for overcurrent, phases and earth 48/14 Starting time supervision, locked rotor 66/86 Restart inhibit 51M Load jam protection, motor statistics 27/59 Under-/overvoltage 81O/U Under-/overfrequency 27/47/59(N)Flexible protection (index quantities derived from 32/55/81R current and voltages): Voltage, power, p.f., rate-of-frequency-change protection HG 48/14 66/86 51M Starting time supervision, locked rotor Restart inhibit Load jam protection, motor statistics
Motor
HA 0 1 2 3 4 7 Z X 9 9 2)
ARC, fault locator, synchronization Without 79 21FL 79, 21FL 25 25, 79, 21FL
With auto-reclosure With fault locator With auto-reclosure, with fault locator With synchronization With synchronization, auto-reclosure, fault locator
ATEX100 Certification For protection of explosion-protected motos (increased-safety type of protection "e"
1) Only with insensitive earth-current transformer when position 7 = 1, 5, 7. 2) This variant might be supplied with a previous firmware version.
5/218
Accessories
Description DIGSI 4 Software for configuration and operation of Siemens protection units running under MS Windows 2000/XP Professional Edition Basis Full version with license for 10 computers, on CD-ROM (authorization by serial number)
Order No.
7XS5400-0AA00
Professional DIGSI 4 Basis and additionally SIGRA (fault record analysis), CFC Editor (logic editor), Display Editor (editor for default and control displays) and DIGSI 4 Remote (remote operation) Professional + IEC 61850 Complete version: DIGSI 4 Basis and additionally SIGRA (fault record analysis), CFC Editor (logic editor), Display Editor (editor for default and control displays) and DIGSI 4 Remote (remote operation) + IEC 61850 system configurator IEC 61850 System configurator Software for configuration of stations with IEC 61850 communication under DIGSI, running under MS Windows 2000 or XP Professional Edition Optional package for DIGSI 4 Basis or Professional License for 10 PCs. Authorization by serial number. On CD-ROM
7XS5402-0AA00
7XS5403-0AA00
5
7XS5460-0AA00
SIGRA 4 Software for graphic visualization, analysis and evaluation of fault records. Can also be used for fault records of devices of other manufacturers (Comtrade format). Running under MS Windows 2000 or XP Professional Edition. (generally contained in DIGSI Professional, but can be ordered additionally) Authorization by serial number. On CD-ROM. 7XS5410-0AA00 Temperature monitoring box 24 to 60 V AC/DC 90 to 240 V AC/DC Varistor/Voltage Arrester Voltage arrester for high-impedance REF protection 125 Vrms; 600 A; 1S/S 256 240 Vrms; 600 A; 1S/S 1088 Connecting cable Cable between PC/notebook (9-pin con.) and protection unit (9-pin connector) (contained in DIGSI 4, but can be ordered additionally) Cable between temperature monitoring box and SIPROTEC 4 unit - length 5 m /16.4 ft - length 25 m /82 ft - length 50 m /164 ft Manual for 7SJ64 English
7XV5662-2AD10 7XV5662-5AD10
C53207-A401-D76-1 C53207-A401-D77-1
C53000-G1140-C20 7-x 1)
5/219
Accessories
LSP2289-afp.eps
Description Terminal safety cover Voltage/current terminal 18-pole/12-pole Voltage/current terminal 12-pole/8-pole Connector 2-pin Connector 3-pin Crimp connector CI2 0.5 to 1 mm2
Mounting rail
LSP2090-afp.eps
LSP2091-afp.eps
1) 1)
Crimp connector: Type III+ 0.75 to 1.5 mm Crimp connector: Type III+ 0.75 to 1.5 mm Crimping tool for Type III+ and matching female Crimping tool for CI2 and matching female Short-circuit links for current terminals for other terminals Mounting rail for 19" rack
2-pin connector
3-pin connector
LSP2093-afp.eps
5/220
LSP2092-afp.eps
Connection diagram
*) For pinout of communication ports see part 16 of this catalog. For allocation of terminals of the panel surface mounting version refer to the manual (http://www.siprotec.com).
5/221
Connection diagram
*) For pinout of communication ports see part 16 of this catalog. For allocation of terminals of the panel surface mounting version refer to the manual (http://www.siprotec.com).
5/222
Connection diagram
*) For pinout of communication ports see part 16 of this catalog. For allocation of terminals of the panel surface mounting version refer to the manual (http://www.siprotec.com).
1) Power relays are intended to directly control motorized switches. The power relays are interlocked so only one relay of each pair can close at a time, in order to avoid shorting out the power supply. The power relay pairs are BO6/BO7, BO8/BO9. If used for protection purposes only one binary output of a pair can be used.
5/223
Connection diagram
*) For pinout of communication ports see part 16 of this catalog. For allocation of terminals of the panel surface mounting version refer to the manual (http://www.siprotec.com). 1) Power relays are intended to directly control motorized switches. The power relays are interlocked so only one relay of each pair can close at a time, in order to avoid shorting out the power supply. The power relay pairs are BO6/BO7, BO8/BO9, BO13/BO14, BO15/BO16. If used for protection purposes only one binary output of a pair can be used.
5/224
Connection diagram
1) Power relays are intended to directly control motorized switches. The power relays are interlocked so only one relay of each pair can close at a time, in order to avoid shorting out the power supply. The power relay pairs are BO6/BO7, BO8/BO9, BO13/BO14, BO15/BO16. If used for protection purposes only one binary output of a pair can be used.
5/225
Connection diagram
*) For pinout of communication ports see part 16 of this catalog. For allocation of terminals of the panel surface mounting version refer to the manual (http://www.siprotec.com).
5/226
Dimension drawings in mm / inch Dimension drawings for SIPROTEC 4 1/3 x 19" housing (7XP20)
5
Side view Fig. 16/22 Housing for panel flush mounting/ cubicle mounting (1/3 x 19") Rear view 1 7SA610, 7SD61, 7SJ64 Rear view 2 7SJ61, 7SJ62, 7UT612, 7UM611 Panel cutout
Side view
5/227
Dimension drawings in mm / inch Dimension drawings for SIPROTEC 4 1/2 x 19" flush-mounting housings (7XP20)
Side view 1
Side view 2
Panel cutout
Rear view 1 7SA61/63, 7UM621, 7UM623 7SJ64 Fig. 16/24 1/2 x 19" flush-mounting housing
5/228
Dimension drawings in mm / inch Dimension drawings for SIPROTEC 4 1/1 x 19" flush-mounting housings (7XP20)
Side view 1
Side view 2
* Terminals M and L additionally for 7UT635 and 7SJ647 only ** Terminals H and G not for 7SJ645 and 7SJ647 Panel cutout Rear view 1 7SA6, 7UM622, 7SJ64, 7UT633, 7UT635
Rear view 2 7SJ63, 6MD63 Fig. 16/25 1/1 x 19" flush-mounting housing
5/229
Dimension drawings in mm / inch Dimension drawings for SIPROTEC 4 1/2 and 1/1 x 19" surface-mounting housings (7XP20)
Side view
Front view 1/1 x 19" surface-mounting housing 7XP20 (without sloped FO case) Fig. 16/26 1/2 and 1/1 x 19" surface-mounting housing
5/230
Dimension drawings in mm / inch Dimension drawings for SIPROTEC 4 1/2 and 1/1 x 19" housings with detached operator panel
Rear view
Panel cutout
5/231