Wiring-Soldering and Crimping Repairs - TSB 05-18-7 Service Tips
Wiring-Soldering and Crimping Repairs - TSB 05-18-7 Service Tips
TSB 05-18-7
FORD: 2000-2006 Crown Victoria, Focus, Mustang, Taurus 2002-2005 Thunderbird 2005-2006 Five Hundred, Ford GT, Freestyle 2006 Fusion 2000-2003 Explorer Sport, Windstar 2000-2005 Excursion 2000-2006 E-Series, Expedition, Explorer, F-150, F-Super Duty, Ranger 2001-2005 Explorer Sport Trac 2001-2006 Escape 2004-2006 Freestar 2005-2006 Escape Hybrid 2000-2006 F-650, F-750 2006 Low Cab Forward
LINCOLN: 2000-2006 LS, Town Car 2006 Zephyr 2000-2006 Navigator 2002-2003 Blackwood 2003-2005 Aviator 2006 Mark LT MERCURY: 2000-2002 Cougar 2000-2005 Sable 2000-2006 Grand Marquis 2005-2006 Montego 2006 Milan 2000-2006 Mountaineer 2004-2006 Monterey 2005-2006 Mariner 2006 Mariner Hybrid
This article supersedes TSB 03-11-6 to update the service procedure, vehicle lines and model years.
ISSUE
Wire harness repairs are supported through the availability of individual components such as: Wire terminals with machine crimped pigtails Hard shell connectors Dual wall heat shrink tubing Complete, loaded, wiring pigtail kits
Some of the available tools and service parts that are helpful when performing wiring harness repairs are: Motorcraft Wiring Pigtail Catalog (see www.motorcraft.com for more information) Rotunda Wire Splice Toolkit 164-R5903 (order through 1-800-Rotunda) General Wire Terminal Repair Kit (order through Ford Component Sales)
NOTE: The information in Technical Service Bulletins is intended for use by trained, professional technicians with the knowledge, tools, and equipment to do the job properly and safely. It informs these technicians of conditions that may occur on some vehicles, or provides information that could assist in proper vehicle service. The procedures should not be performed by do-it-yourselfers. Do not assume that a condition described affects your car or truck. Contact a Ford, Lincoln, or Mercury dealership to determine whether the Bulletin applies to your vehicle. Warranty Policy and Extended Service Plan documentation determine Warranty and/or Extended Service Plan coverage unless stated otherwise in the TSB article.The information in this Technical Service Bulletin (TSB) was current at the time of printing. Ford Motor Company reserves the right to supercede this information with updates.The most recent information is available through Ford Motor Companys on-line technical resources.
PAGE 1
ACTION
REPAIR VS REPLACEMENT The approved procedure is to repair wiring harnesses with pigtail kits, wire terminals, or hard shell connectors when available. The only exceptions to this procedure are when: The repair cost exceeds the cost to replace the wiring harness There are no component parts released to service the wiring harness RESTRAINTS RELATED WIRING REPAIRS If restraints connectors or wiring circuits are contained in a stand-alone harness, do not repair them; replace the restraints harness unless directed to repair the circuit by a TSB or other Ford Motor Company publication. If restraints connectors or wiring circuits are contained in the main vehicle wiring harnesses (14401, 14A005, etc.), they should be repaired using the solder and heat-shrink repair procedure specified in this TSB. The General Wire Terminal Repair Kit contains gold plated terminated pigtails (with white insulation) and dual wall heat shrink tubing to perform these repairs. Loaded wiring pigtail kits with gold plated terminals are also available in the parts catalog. SERVICE TIPS Refer to applicable model year wiring diagrams for circuit information. Twisted Wire Circuits For Twisted Wire circuit repair (Figure 1), the twisting must not be disrupted for more than 2 (51 mm) Twist the repaired wires in the same direction and with the same general twist rate as the original wiring. Reapply the shielding on shielded circuits. Figure 1 - Article 05-18-7
Figure 2 - Article 05-18-7 For 16 AGW and Smaller Diameter Wire 1. Strip 1 1/2 (37.2mm) of insulation from Wire #1 and 3/4 (19.5mm) of insulation from Wire #2, taking care not to nick or cut wire strands (Figure 3). Pull wire straight from stripper. If wire is pulled at an angle, wire strands may be cut off. If more than one (1) strand is cut off during stripping, cut off the end and re-strip.
PAGE 2
Figure 3 - Article 05-18-7 2. Install heat shrink tubing at least 1 (26 mm) away from one of the stripped ends being spliced. Twist wires together. Solder wires together (Figure 4).
NOTE USE ROSIN CORE MILDLY ACTIVATED (RMS) SOLDER. DO NOT USE ACID CORE SOLDER FOR WIRE REPAIR. 3. Bend Wire #1 back in a straight line for sealing (Figure 4). Inspect solder joint bond.
Figure 5 - Article 05-18-7 For 14 AGW and Larger Diameter Wire (Excluding Restraints Wiring Repairs) 1. Figure 4 - Article 05-18-7 4. Evenly position heat shrink tubing over wire repair (Figure 5). Strip 1/4 (6.35mm) of insulation from pigtail wire end once the wire lengths are sized so repairs can be staggered. Take care not to nick or cut wire strands. Pull wire straight from stripper. If wire is pulled at an angle, wire strands may be cut off. If more than one (1) strand is cut off during stripping, cut off the end and re-strip.
PAGE 3
5.
6.
Figure 6 - Article 05-18-7 3. Identify the appropriate crimping chamber of the Rotunda 164-R5901 Pro-Crimper (or equivalent) by matching the wire size on the dies with the wire size stamped on the butt splice (Figure 7). Hold the crimping tool so the identified wire sizes are facing you. Squeeze tool handles together until the ratchet releases, then allow the jaws of the tool to open fully. Figure 8 - Article 05-18-7 7. Holding the wire in place, squeeze tool handles together until ratchet releases. Allow tool handles to open, then remove crimped butt splice. To crimp the other half of the splice, reposition the un-crimped wire barrel in the same crimping chamber, and repeat Steps 3-8. If splice cannot be turned for crimping the other half, turn the tool around. Check for acceptable crimp. a. Crimp should be centered on each end of the butt splice. It is acceptable for crimp to be slightly off center, but not off the end of the butt splice (Figure 9-a). b. Wire insulation does not enter butt splice. Wire is flush with or extends slightly beyond end of butt splice (Figure 9-b). Figure 7 - Article 05-18-7 c. Wire is visible through inspection hole of splices (Figure 9-c).
8.
9.
PAGE 4
PAGE 5