IT S811 Soft Starter - User Manual
IT S811 Soft Starter - User Manual
MN03902002E
MN03902002E
Table of Contents
LIST OF FIGURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LIST OF TABLES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SAFETY The Meaning of Safety Statements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . IT. Soft Starter Safety Statements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Dangers, Warnings, Cautions and Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CHAPTER 1 OVERVIEW General Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . General Appearance Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CHAPTER 2 RECEIPT/UNPACKING General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CHAPTER 3 INSTALLATION Mounting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Power Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Control Wiring Inputs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CHAPTER 4 SPECIFICATIONS Environmental . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Physical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CE Conformance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Short Circuit Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CHAPTER 5 FUNCTIONAL DESCRIPTION Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . QCPort Network Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CHAPTER 6 CONFIGURATION Programming the S811 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . S801 to S811 Comparison . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CHAPTER 7 SETUP AND STARTING Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CHAPTER 8 TROUBLESHOOTING General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Before You Begin to Troubleshoot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Dene the Problem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fault Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CHAPTER 9 PARTS AND SERVICE Renewal Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Service. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv v vii viii ix 1-1 1-2 2-1 2-1 2-1 3-1 3-9 3-12 4-1 4-1 4-2 4-3 5-1 5-1 5-4 5-4 6-1 6-2 7-1 7-1 8-1 8-1 8-2 8-6 9-1 9-1
ii
MN03902002E
MN03902002E
iii
List of Figures
Figure 1-1: The Cutler-Hammer Intelligent Technologies (IT.) S811 Soft Starter . . . . . . Figure 3-1: Warning Tag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Figure 3-2: Power Wiring Alternatives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Figure 3-3: N Frame (65 mm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Figure 3-4: R Frame (110 mm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Figure 3-5: T Frame (200 mm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Figure 3-6: U Frame (200 mm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Figure 3-7: V Frame (290 mm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Figure 3-8: EMA91 Digital Interface Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Figure 3-9: V Frame Shown with Terminal Cover Removed and EML30 Lug Kit Installed on Load Side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Figure 3-10: Terminal Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Figure 3-11: Basic Connection Diagram for 24V DC 3-Wire Pushbutton STOP/START/JOG/RESET and 24V DC Fault/Ready and Bypass Indication . . . . . . . Figure 3-12: Basic Connection Diagram for 24V DC 2-Wire Switch HAND/OFF/AUTO/RESET and 24V DC Fault/Ready and Bypass Indication . . . . . . . Figure 3-13: Basic Connection Diagram for Use of DIM Control Only . . . . . . . . . . . . . . Figure 3-14: 24V DC Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Figure 3-15: 120V AC Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Figure 3-16: 24V DC Control with Edge Sensing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Figure 5-1: Soft Starter SCRs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Figure 5-2: Ramp Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Figure 5-3: Current Limit Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Figure 5-4: Soft Stop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Figure 6-1: Digital Interface Module (DIM) Display Mode . . . . . . . . . . . . . . . . . . . . . . Figure 6-2: Digital Interface Module (DIM) Parameter Edit Mode . . . . . . . . . . . . . . . . Figure 8-1: Start Command Troubleshooting Flowchart . . . . . . . . . . . . . . . . . . . . . . . . . Figure 8-2: Main Troubleshooting Flowchart #1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Figure A-1: Navigation Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Figure B-1: Overload Trip Curves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Figure E-1: IT. Soft Starter DIM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Figure E-2: Pump Start Ramp and Soft Pump Stop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Figure F-1: DIM (Digital Interface Module) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Figure F-2: Display Mode LCD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Figure F-3: Parameter Edit Mode LCD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Figure F-4: Fault Mode LCD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Figure F-5: Soft Key Functions Above Soft Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Figure F-6: Predened Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Figure F-7: Status Bar on LCD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Figure F-8: Device Connection (User Display Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Figure F-9: Connection Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Figure F-10: Mode of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Figure F-11: Connection Destination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Figure F-12: HAND/AUTO Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Figure F-13: Motor Control Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Figure F-14: Bar Indicates Menu Position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Figure F-15: Bar Indicates Item Position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Figure F-16: Bar Indicates Edited Value . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 3-3 3-4 3-5 3-5 3-6 3-6 3-7 3-7 3-11 3-12 3-14 3-15 3-15 3-20 3-20 3-21 5-1 5-2 5-3 5-3 6-1 6-2 8-2 8-4 A-1 B-3 E-1 E-2 F-1 F-2 F-2 F-2 F-3 F-4 F-5 F-5 F-5 F-6 F-7 F-7 F-7 F-8 F-8 F-9
iv
MN03902002E
List of Tables
Table 3-1: Required Mounting Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 3-2: Weight Support Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 3-3: Line and Load Power Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 3-4: 12-Pin Terminal Block Wiring Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 3-5: S811 Terminal Block Control Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 3-6: 24V DC Power Supply Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 3-7: 24V DC Power Supplies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 4-1: Environmental Specications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 4-2: Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 4-3: Agency Standards and Certications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 4-4: EMC Immunity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 4-5: Short Circuit Ratings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 6-1: S801 to S811 Setup Cross-Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 8-1: Start Command Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 8-2: Troubleshooting Status LED OFF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 8-3: Troubleshooting Status LED GREEN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 8-4: Troubleshooting Fault Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 8-5: Resetting the S811 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 9-1: DIM Digital Interface Module Renewal Parts . . . . . . . . . . . . . . . . . . . . . . . . . . Table A-1: Monitoring Menu 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table A-2: Motor Control Menu 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table A-3: Conguration Menu 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table A-4: Protections Menu 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table A-5: Network Setup Menu 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table A-6: Network Status Menu 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table A-7: LCD DIM Setup Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table B-1: Overload Adjustment Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table B-2: Thermal Motor Overload Times . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table B-3: Motor Parameters Required for Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table B-4: Instantaneous Over Current Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table B-5: Motor Stall Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table B-6: SCR Over Current Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table B-7: Motor Jam Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table B-8: Motor Over Current Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table B-9: Motor Under Load Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8 3-8 3-10 3-12 3-13 3-16 3-17 4-1 4-1 4-1 4-2 4-3 6-2 8-3 8-5 8-5 8-6 8-8 9-1 A-2 A-3 A-4 A-5 A-6 A-7 A-8 B-1 B-2 B-4 B-4 B-4 B-4 B-5 B-5 B-5
MN03902002E
vi
MN03902002E
Safety
Eatons electrical business has made every effort to provide you with the safest motor starters on the market. However, we wish to point out how to safely operate and troubleshoot your starter.
! ! !
The Safety Alert Symbol means ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Le symbole dalerte signie ATTENTION ! SOYEZ VIGILANT ! VOTRE SECURITE EST EN JEU ! El smbolo de alerta de seguridad signica ATENCIN! EST ALERTA! SU SEGURIDAD EST EN JUEGO!
Danger
Danger means that failure to follow the safety statement will result in serious personal injury, death, or substantial property damage.
Danger
Danger signie que linobservation de lnonc de scurit entranera des blessures corporelles graves, la mort ou des dgts matriels substantiels.
Peligro
Peligro signica que si no se respeta la indicacin de seguridad, se producirn lesiones personales graves, la muerte o dao considerable a la propiedad.
Warning
Warning means that failure to follow the safety statement could result in serious personal injury, death, or substantial property damage.
Avertissement
Avertissement signie que linobservation de lnonc de scurit pourrait entraner des blessures corporelles graves, la mort ou des dgts matriels substantiels.
Advertencia
Advertencia signica que si no se respeta la indicacin de seguridad se pueden producir lesiones personales graves, la muerte o daos considerables a la propiedad.
Caution
Attention
Precaucin
Caution means that failure to follow the safety statement may result in minor or moderate personal injury or property damage.
Attention signie que linobservation de lnonc de scurit peut entraner des blessures corporelles mineures ou modrs ou des dgts matriels.
Precaucin signica que si no se respeta la indicacin de seguridad, se pueden producir lesiones personales menores o moderadas, o daos a la propiedad.
Notice
Notice means that failure to follow these instructions could cause damage to the equipment or cause it to operate improperly.
Avis
Avis signie que linobservation de ses instructions pourrait entraner des dgts ou le mauvais fonctionnement de lquipement.
Aviso
Aviso signica que si no se siguen estas instrucciones, se pueden producir daos al equipo o provocar que funcione de manera incorrecta.
MN03902002E
vii
Notice
Make sure you read and understand the procedures in this manual before you attempt to operate or set up the equipment.
Avis
Bien lire et comprendre les procdures contenues dans ce manuel avant de tenter le fonctionnement ou la mise en place de lquipement.
Aviso
Asegrese de leer y entender los procedimientos en este manual antes de intentar operar o congurar el equipo.
Warning
This instruction manual should be used for proper installation, setup and operation of the starter. Improperly installing and maintaining this product can result in serious personal injury or property damage. Before attempting installation, setup or operation, read and understand all of this manual.
Avertissement
Ce manuel dinstructions doit tre utilis pour linstallation, mise en place et opration rgls dun dmarreur. La mauvaise installation et entretien de ses produits pourraient entraner des blessures corporelles graves ou des dommages matriels. Avant de tenter linstallation ou lentretien, bien lire et comprendre ce manuel en entier.
Advertencia
Este manual de instrucciones debe utilizarse para la correcta instalacin, conguracin y operacin del arrancador. La instalacin o el mantenimiento inadecuado de este producto puede ocasionar serias lesiones personales o daos al material. Antes de intentar la instalacin, la conguracin o la operacin lea y entienda todo el manual.
Notice
Power factor capacitors: Do not connect power factor correcting capacitors to the load side of the starter. They will cause the starter to fail. If capacitors are used, they must be connected to the line side of the starter, as far upstream as possible.
Avis
Condensateurs de compensation : Ne pas raccorder ces appareils au ct charge du dmarreur. Cela entranera la dfaillance du dmarreur. Si des condensateurs sont utiliss, ils doivent tre raccorder au ct ligne du dmarreur, aussi loin amont que possible.
Aviso
Capacitores correctores del factor de potencia: No conecte estos capacitores del lado de la carga del arrancador. Esto ocasionar la falla de este ltimo. Si se usan capacitores, deben conectarse del lado de la lnea del arrancador, tan lejos de la entrada como sea posible.
viii
MN03902002E
Do not apply a disconnect device on the output of the IT. Soft Starter unless a means to turn off the soft starter when disconnect switch is open is utilized. Opening disconnect while the IT. Soft Starter is operating may cause a malfunction. Closing disconnect switch while the IT. Soft Starter is operating will result in a soft starter failure and potential equipment damage and personnel hazard.
MN03902002E
ix
Warnings Warning
After mounting the unit, remove and discard the lifting eye and packaging bolts before continuing with the installation process.
Avertissement
Aprs que lappareil sera support, enlever et jeter les illets de levage et les boulons de lemballage avant de poursuivre linstallation.
Advertencia
Despus de montar la unidad, retire y elimine la argolla de izada y los pernos de embalaje antes de continuar con el proceso de instalacin.
Warning
Make sure you read and understand all of the safety statements in the safety section of this manual before you begin troubleshooting.
Avertissement
Sassurer de bien lire et comprendre les noncs de scurit dans le passage de scurit de ce manuel avant de commencer le dpannage.
Advertencia
Antes de comenzar a solucionar problemas, asegrese de leer y comprender todas las indicaciones de seguridad que aparecen en la seccin de seguridad de este manual.
MN03902002E
Cautions
Caution
Attention
Precaucin
The S811V soft starter weighs approximately 100 Lbs. (45 kg). To prevent personal injury or equipment damage, use proper lifting equipment (such as a oor crane) to safely lift and install the soft starter. A lifting eye is provided at the line end of the soft starter.
Le dmarreur progressif S811V pse environ 45 kg (100 livres). Pour viter des blessures corporelles ou des dgts matriels, utiliser une machine de levage approprie (comme une grue datelier) pour soulever et installer le dmarreur progressif sans encombre. Un illet de levage est prvu au ct ligne du dmarreur progressif.
El arrancador suave S811V pesa aproximadamente 45 kg (100 lb.). Para evitar que se produzcan lesiones personales o daos al equipo, use el equipo para elevar adecuado (como un brazo de elevacin) a n de levantar e instalar con seguridad el arrancador suave. Se proporciona una argolla de izada en el extremo de del arrancador suave.
Caution
Attention
Precaucin
Only apply 24V DC to the terminal block unless specied otherwise in this manual. All control wiring is 22 12 AWG (0.33 2.5 mm2). Failure to follow this caution could result in severe damage to the controller.
Appliquer seulement 24V CC la barrette bornes sauf ce manuel offre davis contraire. Tout le cblage de commande est de calibre 0,33 2,5 mm2 (22 12 AWG). Linobservation de cet nonc pourrait entraner des dgts matriels au contrleur.
Aplique slo 24 V CC al bloque de terminales, a menos que se especique lo contrario en este manual. Todo el cableado de control es de 0.33 2.5 mm2 (22 12 AWG). Si no respeta esta precaucin, se pueden producir daos graves al controlador.
Caution
Attention
Precaucin
Never megger a motor while it is connected to the IT. Soft Starter. Disconnect the leads at the IT. Soft Starter before meggering the motor.
Ne jamais rgler un moteur alors quil est branch au dmarreur progressif IT. Dbrancher les ls au dmarreur progressif IT. Avant de rgler le moteur.
Nunca efecte pruebas del motor con un meghmetro mientras est conectado al arrancador Soft Starter IT. Desconecte los cables en el arrancador IT. antes de usar el meghmetro.
MN03902002E
xi
Notes Notice
The S811V Soft Starter includes mounting hardware (8 1/4-20 x 1.5 Allen hex head cap screws and special washers). Do not substitute for this hardware. See Figure 3-7 on Page 3-7 for panel hole locations. Applicable codes or standards must be considered before locating and mounting the soft starter. The four special rectangular/rounded washers must be used on the two innermost mounting holes on both the line and load side of the soft starter.
Avis
Le dmarreur progressif S811V inclut des matriels de support (vis tte hexagonale 8-1/4-20 x 1,5 et des rondelles spciales). Ne substituer pas pour ces matriels. Consulter la Figure 3-7 de la Page 3-7 pour les locations des trous dans le panneau. Tenir compte des normes et des codes existants avant de localiser et de monter le dmarreur progressif. Les quatre rondelles rectangulaires/ circulaires spciales doivent tre utiliser aux deux trous de support les plus intrieurs sur le ct ligne et le ct charge du dmarreur progressif.
Aviso
El arrancador suave S811V incluye piezas metlicas de montaje (tornillos Allen de cabeza hexagonal de 8 1/4-20 x 1.5 y arandelas especiales). No las sustituya. Consulte la Figura 3-7 que aparece en la pgina 3-7 para conocer las ubicaciones de los oricios del panel. Antes de ubicar y montar el arrancador suave, se deben considerar los cdigos o las normas pertinentes. Las cuatro arandelas rectangulares/ redondas especiales se deben usar en los dos oricios de montaje que se encuentren ms al interior, en los lados de lnea y de carga del arrancador suave.
xii
MN03902002E
Chapter 1 Overview
General Introduction
The Cutler-Hammer Intelligent Technologies S811 IT. Soft Starter from Eatons electrical business is an electronic, self-contained, panel- or enclosure-mounted motor soft-starting device. It is intended to provide three-phase induction motors with a smooth start, both mechanically and electrically. The S811 Soft Starters utilize six SCRs connected in a full wave power bridge. Varying the SCR conduction period controls the voltage applied to the motor. This in turn controls the torque developed by the motor. After the motor reaches speed, contacts are closed to bypass the SCRs. The S811 has built-in communications capabilities through Cutler-Hammer QC (Quick Connect) Port. The S811 Soft Starter utilizes a DIM (Digital Interface Module) that allows the user to congure the device and read system parameters. The DIM includes an easy-to-read LCD display and keypad to scroll through the menus. The DIM allows the user to modify control parameters, enable or disable protections, set communication variables, monitor system parameters such as line voltages and currents and access the fault queue. The S811 is designed to fulll the industrial service requirements for applications such as Chillers, Pumps and Machine Tools that require less than 85% of the motors rated starting torque for worst case starting condition. The S811 meets all relevant specications set forth by NEMA ICS 1, ICS 2 and ICS 5, UL 508, IEC 60947-4-2, CE and CSA. This user manual covers everything you need to know in order to install, set up, operate, troubleshoot and maintain the S811. However, no publication can take into account every possible situation. If you require further assistance with any aspect of this product, or a particular application, please contact us. For contact information, please see Chapter 9.
MN03902002E
1-1
Load Output
Figure 1-1: The Cutler-Hammer Intelligent Technologies (IT.) S811 Soft Starter
1-2
MN03902002E
Chapter 2 Receipt/Unpacking
General
Upon receipt of the unit, verify that the catalog number and unit options stated on the shipping container match those stated on the order/purchase form. Inspect the equipment upon delivery. Report any crate or carton damage to the carrier prior to accepting the delivery. Have this information noted on the freight bill. Eaton is not responsible for damage incurred in shipping.
Unpacking
Remove all packing material from the unit. Be sure to remove all packing material from lug locations. Also, make sure no packing material blocks the airow near the fans. For V frame units, verify mounting hardware has been included with shipment. Check the unit for any signs of shipping damage. If damage is found after unpacking, report it to the freight company. Retain the packaging materials for carrier to review. Verify that the units catalog number and options match those stated on the order/purchase form.
Storage
It is recommended that the unit be stored in its original shipping box/crate until it is to be installed. The unit should be stored in a location where:
The ambient temperature is -58F 158F (-50C 70C) The relative humidity is 0% 95%, non-condensing The environment is dry, clean and non-corrosive The unit will not be subjected to high shock or vibration conditions
MN03902002E
2-1
2-2
MN03902002E
Chapter 3 Installation
Mounting
Models S811N, S811R and S811T The S811 is easy to mount. It does not require any special tools. To aid you with panel layout, refer to the dimension drawings in Figures 3-3 through 3-7 of this manual. Drill and tap holes per mounting hole location as shown. To mount the unit, use all the hardware specied in Table 3-1 on Page 3-8. Tighten to the torque specied. The T frame S811 is supplied with a lifting eye mounted on the center phase of the line end of the device. This will aid in mounting the unit.
Warning
After mounting the unit, remove and discard the lifting eye and packaging bolts before continuing with the installation process.
Avertissement
Aprs que lappareil sera support, enlever et jeter les illets de levage et les boulons de lemballage avant de poursuivre linstallation.
Advertencia
Despus de montar la unidad, retire y elimine la argolla de izada y los pernos de embalaje antes de continuar con el proceso de instalacin.
Model S811V10 IMPORTANT: For model S811V10N3S, see additional installation requirements noted on Page 3-4.
Caution
Attention
Precaucin
The S811V soft starter weighs approximately 100 Lbs. (45 kg). To prevent personal injury or equipment damage, use proper lifting equipment (such as a oor crane) to safely lift and install the soft starter. A lifting eye is provided at the line end of the soft starter.
Le dmarreur progressif S811V pse environ 45kg (100 livres). Pour viter des blessures corporelles ou des dgts matriels, utiliser une machine de levage approprie (comme une grue datelier) pour soulever et installer le dmarreur progressif sans encombre. Un illet de levage est prvu au ct ligne du dmarreur progressif.
El arrancador suave S811V pesa aproximadamente 45 kg (100 lb.). Para evitar que se produzcan lesiones personales o daos al equipo, use el equipo para elevar adecuado (como un brazo de elevacin) a n de levantar e instalar con seguridad el arrancador suave. Se proporciona una argolla de izada en el extremo de del arrancador suave.
MN03902002E
3-1
Notice
The S811V soft starter includes mounting hardware (8 1/4-20 x 1.5 Allen hex head cap screws and special washers). Do not substitute for this hardware. See Figure 3-7 on Page 3-7 for panel hole locations. Applicable codes or standards must be considered before locating and mounting the soft starter. The four special rectangular/rounded washers must be used on the two innermost mounting holes on both the line and load side of the soft starter.
Avis
Le dmarreur progressif S811V inclut des matriels de support (vis tte hexagonale 8-1/4-20 x 1,5 et des rondelles spciales). Ne substituer pas pour ces matriels. Consulter la Figure 3-7 de la Page 3-7 pour les locations des trous dans le panneau. Tenir compte des normes et des codes existants avant de localiser et de monter le dmarreur progressif. Les quatre rondelles rectangulaires/ circulaires spciales doivent tre utiliser aux deux trous de support les plus intrieurs sur le ct ligne et le ct charge du dmarreur progressif.
Aviso
El arrancador suave S811V incluye piezas metlicas de montaje (tornillos Allen de cabeza hexagonal de 8 1/4-20 x 1.5 y arandelas especiales). No las sustituya. Consulte la Figura 3-7 que aparece en la pgina 3-7 para conocer las ubicaciones de los oricios del panel. Antes de ubicar y montar el arrancador suave, se deben considerar los cdigos o las normas pertinentes. Las cuatro arandelas rectangulares/ redondas especiales se deben usar en los dos oricios de montaje que se encuentren ms al interior, en los lados de lnea y de carga del arrancador suave.
Drill and tap the eight mounting holes. Thread the two lower middle screws (with special at washer and lockwasher) into the panel before lifting the soft starter. These two screws will assist in mounting. Special mounting hardware is included with the soft starter. Hardware supplied must be used. Hook lifting equipment to the soft starter lifting eye. If you are using a crane, minimize the chain length between the boom and the soft starter. Make sure that the back of the soft starter is oriented to the panel-mounting surface. Make sure that the lifting equipment hook is fully engaged with the soft starter lifting eye before lifting. Slowly lift the soft starter to about 2 in. (5 cm) above the mounting location. Then move it back against the mounting panel. Carefully lower the soft starter onto the two mounting screws. Make sure the screws align with the slots on the load end of the soft starter, and that the two washers are between the soft starter base and the screw head. Install and tighten the remaining six mounting screws, washers and lockwashers. Then tighten the two lower middle screws. Tighten all eight screws to 50 Lb-in (5.6 Nm). Disengage and remove the lifting equipment.
Warning
After mounting the unit, remove and discard the lifting eye and packaging bolts before continuing with the installation process.
Avertissement
Aprs que lappareil sera support, enlever et jeter les illets de levage et les boulons de lemballage avant de poursuivre linstallation.
Advertencia
Despus de montar la unidad, retire y elimine la argolla de izada y los pernos de embalaje antes de continuar con el proceso de instalacin.
3-2
MN03902002E
WARNING AVERTISSEMENT
MN03902002E
3-3
S811V10N3S Installation Requirements 1. Install the device in a minimum enclosure size 30 ft3. 2. Two (2) forced air ventilation fans with a min. 500 ft3/min, at a location for air in bottom right or left corner and air out opposite upper right or left corner. 3. RD circuit breaker. 4. For power wiring: Use four (4) 500 MCM cables for each phase between RD circuit breaker and Soft Starter. OPTIONAL: Two (2) 3" x 1/4" bus with a 1/4" spacer per terminal. Note: See Figure 3-2 for alternative layouts. 5. Line and load service entrance wiring must not cross in the enclosure.
Line Service (4) 350 MCM/Terminal RD Circuit Breaker RD Circuit Breaker 6" Minimum Distance Isolation Contactor 6" Minimum Distance S811V10N3S IT. Soft Starter Line Service (4) 350 MCM/Terminal
3-4
MN03902002E
Dimensions
1.97 (50.0)
6.47 (164.4)
2.66 (67.6)
6.87 (174.5)
3.54 (90.0)
7.44 (189.0)
MN03902002E
3-5
6.39 (162.4)
7.67 (194.8)
5.40 (137.2)
.47 (11.9)
C L
7.08 (179.9)
12.72 (323.1)
7.73 (196.3)
3-6
MN03902002E
9.84 (250.0)
7.35 (186.6)
11.05 (280.6)
3.74 (95.0)
2.91 (74.0)
3.08 (78.3)
2.68 (68.0)
.31 (8.0)
MN03902002E
3-7
3-8
MN03902002E
Power Wiring
Using the wiring diagrams in Figures 3-11, 3-12 and 3-13 and Table 3-3 below as guides, connect the line, Motor, and Power Supply wiring in accordance with appropriate local and national codes. Note: To provide optimum motor protection the Line and Motor power wiring should be tightly bundled and run perpendicular to the orientation of the S811. Safety Notices Danger High Voltage
Hazardous voltage can cause electric shock and burns. To avoid shock hazard, disconnect all power to the controller, motor or other control devices before any work is performed on this equipment. Failure to do so will result in personal injury, death or substantial property damage.
Do not apply a disconnect device on the output of the IT. Soft Starter unless a means to turn off the soft starter when disconnect switch is open is utilized. Opening disconnect while the IT. Soft Starter is operating may cause a malfunction. Closing disconnect switch while the IT. Soft Starter is operating will result in a soft starter failure and potential equipment damage and personnel hazard.
Note: Short circuit protection must be applied on the line side of the soft starter. The S811 is to be wired into the three-phase line feeding the three main motor input leads as would be done for normal across-the-line starting. It must not be wired internally between motor windings. Refer to the motor nameplate for correct wiring information for normal across-the-line operation. Contact Eaton if a special motor wiring requirement exists before wiring your starter. By factory default, the S811 is to be connected with an ABC phase rotation on the incoming power wiring. If the motor turns in the incorrect direction upon energization, exchange two phases at the motor terminal box or at the output terminals of the soft starter. Changing the input wiring will cause a voltage phase reversal trip.
MN03902002E
3-9
If the input phase sequence to the S811 must be ACB, the incoming phase sequence will need to be changed to ACB. Setting ACB as the incoming phase sequence causes the ABC incoming phase sequence to cause a voltage phase reversal trip. IMPORTANT: The reversing contactor must never be switched while the soft starter is operating. In order to gain the full benet of the S811 with a reversing contactor, the S811 needs to be OFF when switching the direction. The soft starter settings must account for catching a motor spinning in the opposite direction upon soft restarts. The time required for slowing the motor to a stop and then ramping up to speed in the opposite direction adds to the overall starting time. This will also impact the overload protection setting. See the Motor/Application Considerations in Appendix D of this manual for information on typical motor winding congurations. Line and Load power wiring data is shown in Table 3-3. Table 3-3: Line and Load Power Wiring
Frame Size N Number of Lug Kit Options Conductors Supplied Standard with Box Lugs 1 Wire Sizes Cu 75C Lug Type Only Box Lug 2 AWG 4 6 AWG 8 AWG 10 14 AWG R Supplied Standard with Box Lugs 1 Box Lug 14 8 AWG (2.5 10 mm2) 6 4 AWG (16 25 mm2) 3 3/0 AWG (27 95 mm2) T&U EML22 EML23 EML24 EML25 EML26 V EML28 EML30 EML32 EML33 2 1 2 1 2 2 4 6 4 250 Lb-in (28.3 Nm) 4 1/0 MCM (21.2 53.5 mm2) 4/0 500 MCM (107 240 mm2) 4/0 500 MCM (107 240 mm2) 2/0 300 MCM (70 150 mm2) 2/0 300 MCM (70 150 mm2) 4/0 500 MCM (107 240 mm2) 4/0 500 MCM (107 240 mm2) 4/0 500 MCM (107 240 mm2) 2/0 300 MCM (70 150 mm2) 250 Lb-in (28.3 Nm) 250 Lb-in (28.3 Nm) 225 Lb-in (25.5 Nm) 225 Lb-in (25.5 Nm) 250 Lb-in (28.3 Nm) 250 Lb-in (28.3 Nm) 250 Lb-in (28.3 Nm) 225 Lb-in (25.5 Nm) 2 2 Torque Requirements 50 Lb-in (5.6 Nm) 45 Lb-in (5.0 Nm) 40 Lb-in (4.5 Nm) 35 Lb-in (4.0 Nm) 90 100 Lb-in (10.1 11.3 Nm) N/A Number of Kits Required N/A
Requires special lug cover. Check with Eaton for availability. CSA approved 350 MCM 500 MCM
3-10
MN03902002E
Lugs for T, U and V Frame T, U and V frame units are supplied standard without lugs. If lugs are needed, they can be ordered through your local Eaton distributor. Each lug kit contains three lugs, mounting hardware, and instructions for use on either line or load side of the IT. Soft Starter. Catalog numbers and wire ranges for lug kits are listed in the table above. Lug Installation Danger High Voltage
Hazardous voltage can cause electric shock and burns. Always disconnect power before proceeding with any work on this product.
Note: For additional motor and system protection, a Metal Oxide Varistor (MOV) may be installed on the line side of the unit. An MOV can also be installed on the load side of the Soft Starter if additional protection is desired. Generally, it is more common to use a MOV on the line side. Refer to the instructions provided with the MOV kit. 1. For T, U and V Frame Soft Starters, remove line and load terminal covers by removing the screws that hold each cover (and the MOV, if installed) onto the unit. Note: For N and R Frame Soft Starters, it is not necessary to remove the covers in order to wire the device. Proceed to step 3. 2. After screws are removed, slide covers off of unit. Set the covers and screws aside. 3. Position lugs and install lug mounting screws according to instructions provided with the kit. Tighten lug mounting screws provided with the kit to 120 Lb-in (13.6 Nm). 4. Wire the appropriate line and load conductors to the IT. Soft Starter (as required by NEC and local codes based on the device rating). 5. Torque bolts as directed by Table 3-3 on Page 3-10 of this manual.
Figure 3-9: V Frame Shown with Terminal Cover Removed and EML30 Lug Kit Installed on Load Side
MN03902002E
3-11
6. Slide the line and load covers back into place on the soft starter. 7. Reinstall the cover screws through the cover and the MOV, if installed. 8. Insert two outer cover screws through cover. 9. Align cover and torque all cover screws to 5 Lb-in (0.6 Nm). Do not overtighten screws.
Caution
Attention
Precaucin
Only apply 24V DC to the terminal block unless specied otherwise in this manual. All control wiring is 22 12 AWG (0.33 2.5 mm2). Failure to follow this caution could result in severe damage to the controller.
Appliquer seulement 24V CC la barrette bornes sauf ce manuel offre davis contraire. Tout le cblage de commande est de calibre 0,33 2,5 mm2 (22 12 AWG). Linobservation de cet nonc pourrait entraner des dgts matriels au contrleur.
Aplique slo 24 V CC al bloque de terminales, a menos que se especique lo contrario en este manual. Todo el cableado de control es de 0.33 2.5 mm2 (22 12 AWG). Si no respeta esta precaucin, se pueden producir daos graves al controlador.
Figure 3-10: Terminal Block Table 3-4 provides the 12-pin terminal block wiring capacity and torque requirements for the control wiring. Table 3-4: 12-Pin Terminal Block Wiring Capacity
Wire Size 22 14 AWG (0.33 2.5 mm2) 12 AWG (4.0 mm2) Number of Conductors 2 1 Torque Requirements 3.5 Lb-in (0.4 Nm) 3.5 Lb-in (0.4 Nm)
3-12
MN03902002E
Input Descriptions The IT. Soft Starter has the following control inputs: Table 3-5: S811 Terminal Block Control Wiring
Terminal Block Designation Factory (Pin) Default +
Input Negative
Connections
Permissive P
Input 1
Input 2
Input 3
Input 4
Power supply connections: Connect power supply negative to pin and to system ground 24V DC nominal Connect +24V DC output to pin + (see 24V DC Note: To avoid voltage drop during Power Supply bypass contactor inrush, a minimum of Requirements section for sizing 14 AWG wire should be used between of power supply) the power supply and the + and inputs at the S811 terminal block. Hardwired 24V DC only Pin P, permissive, must be energized STOP (maintained input) (+24V DC) to enable operation of the unit. If power is removed from the permissive circuit at any time, the unit will begin a STOP command. If a soft stop is selected, the soft stop will begin and run to timeout. START 24V DC only Applying 24V DC to Input 1 while P is (momentary energized will initiate a START. As input) shipped from the factory this input is level sensitive. JOG 24V DC only Input 2 is JOG. Applying 24V DC to this (momentary input while P is energized will initiate a input) JOG. HAND/AUTO 24V DC only Must Input 3 is HAND. Hand must be energized be maintained for to enable control (START/STOP/JOG) control from the through the terminal block. terminal block Fault RESET 24V DC only Input 4 is Fault RESET. Energizing this input will reset a fault only after the fault condition has been corrected. Common 3 Amps, @ 120V NO Form A contact: As shipped from the AC/24V DC factory this programmable contact closes NO Dewhen the starters bypass contactor is energized energized. It will remain closed until a STOP is initiated. The motor may continue to run even after the STOP is initiated until the stop ramp has been completed. Common Form C Common Form C contacts: As shipped from the for 96 and 98 factory these programmable contacts will change status when a Fault occurs. NC De3 Amps, @ 120V energized AC/24V DC NO Deenergized 3 Amps, @ 120V AC/24V DC
MN03902002E
3-13
Typical Control Wiring Diagrams Each diagram illustrates a typical wiring scheme for the options described. The terminal block represents the soft starter. The additional Cutler-Hammer items shown on the diagrams are not included, but they may be purchased from Eaton.
Power Supply
Incoming Lines 1 2 3
Disconnect 24V DC + (See Note 1) * E-Stop Stop (See Note 3) Jumper +24V to 3 Start Jog Reset In Bypass Ready Fault Optional 24V DC Pilot Lights (See Note 2) Motor * E-Stop Maintained ** As Required per National and Local Electric Codes + P 1 2 3 4 13 14 95 96 98 L 1/1 L2/3 L3/5 24V DC Power S811 Soft Starter Inputs 24V DC Only
**
Figure 3-11: Basic Connection Diagram for 24V DC 3-Wire Pushbutton STOP/START/JOG/RESET and 24V DC Fault/Ready and Bypass Indication
3-14
MN03902002E
Power Supply
Incoming Lines 1 2 3
Disconnect 24V DC + (See Note 1) * E-Stop Jumper Hand OFF Auto Remote (See Note 3) Contact Reset In Bypass Ready Fault Optional 24V DC Pilot Lights (See Note 2) Motor * E-Stop Maintained ** As Required per National and Local Electric Codes L 1/1 L2/3 L3/5 24V DC Power S811 Soft Starter Inputs 24V DC Only
**
+ P 1 2 3 4 13 14 95 96 98
Jumper +24V to 3
Figure 3-12: Basic Connection Diagram for 24V DC 2-Wire Switch HAND/OFF/AUTO/RESET and 24V DC Fault/Ready and Bypass Indication
Power Supply
Incoming Lines 1 2 3
Disconnect 24V DC + (See Note 1) * E-Stop L 1/1 L2/3 L3/5 24V DC Power S811 Soft Starter Inputs 24V DC Only
**
+ P 1 2 3 4 13 14 95 96 98
Jumper +24V to P
Motor * E-Stop Maintained ** As Required per National and Local Electric Codes
Figure 3-13: Basic Connection Diagram for Use of DIM Control Only
MN03902002E
3-15
Notes: 1. A minimum of wire of 14 AWG (2.5 mm2) should be used between the power supply and the 24V DC + and - terminals. 2. See Using an Auxiliary Relay section below if it is desired to use a relay instead of an indicating lamp for terminals 13, 14, 95, 96 and 98. 3. If an isolation or reversing contactor is used upstream of the S811, Eaton recommends that the user choose the edge level sensing option. Each diagram illustrates a typical wiring scheme for the options described. The terminal block represents the soft starter. The additional Cutler-Hammer items shown on the diagrams are not included, but can be purchased from Eaton. 24V DC Control Power Supply The S811 Soft Starter requires 24V DC control power. The sealed in and inrush characteristics of the S811 Soft Starter are summarized in Table 3-6: Table 3-6: 24V DC Power Supply Requirements
Soft Starter Frame S811N S811R S811T S811U S811V Sealed Watts 25 25 25 25 25 Amps 1.0 1.0 1.0 1.0 1.4 Inrush Watts 240 240 240 240 240 Amps 10 10 10 10 10 Duration (ms) 150 150 150 150 150
For applications where one starter is used with one power supply, the power supply selected must be equal to or greater than both the sealed in and inrush requirements of the starter.
Max Steady State for the Power Supply Outrush for the Power Supply
Multiple starters can be used with one power supply. If the application requires the starters to start at the same time, the power supply must be sized for the sum of the sealed in and inrush power for each starter.
Max Steady State for the Power Supply Outrush for the Power Supply
Multiple starters are typically not commanded to start at the same time. If the application requires the starters not be commanded to start at the same time (>150 ms between start commands), the required power is the sum of the largest inrush power, plus the sealed in power of the running starters. Worst case from a power supply standpoint is the largest inrush starter commanded to start while all the other starters are running.
3-16
MN03902002E
Denitions: SI = Sum of Seal Incurrent LS = Largest Seal Incurrent LI = Largest Inrush Needed TS = Total Seal Incurrent Needed LO = Largest Outrush Needed TS = (SI - LS) LO = TS + LI
Max Steady State for the Power Supply Outrush for the Power Supply LO
SI
The voltage on the S811 + and control terminals must not exceed 30V DC to prevent hardware damage. The S811 will shut down and issue low control voltage fault at control voltages less than 17V DC. The fault will reset at control voltages greater than 18V DC. The Cutler-Hammer control power supplies listed in Table 3-7 are recommended. Table 3-7: 24V DC Power Supplies
Catalog Number PSS55A PSS55B PSS55C PSS160E PSS160C PSS300E PSS600C Continuous Watts 55 55 55 160 160 300 600 Amps 2.3 2.3 2.3 6.5 6.5 12.5 25.0 Peak Amps 10.0 10.0 10.0 13.0 13.0 20.0 50.0 Input Voltage VAC 90 140 180 260 360 500 90 260 360 500 90 260 360 500
Caution
Attention
Precaucin
Only apply 24V DC to the terminal block unless specied otherwise in this manual. All control wiring is 22 12 AWG (0.33 2.5 mm2). Failure to follow this caution could result in severe damage to the controller.
Appliquer seulement 24V CC la barrette bornes sauf ce manuel offre davis contraire. Tout le cblage de commande est de calibre 0,33 2,5 mm2 (22 12 AWG). Linobservation de cet nonc pourrait entraner des dgts matriels au contrleur.
Aplique slo 24 V CC al bloque de terminales, a menos que se especique lo contrario en este manual. Todo el cableado de control es de 0.33 2.5 mm2 (22 12 AWG). Si no respeta esta precaucin, se pueden producir daos graves al controlador.
1. Connect DC common (negative) to terminal -, using a minimum wire of 14 AWG (2.5 mm2). 2. Connect +24V DC positive to terminal +, using a minimum wire of 14 AWG (2.5 mm2). 3. Terminal P (permissive circuit) Must be energized at +24V DC to enable operation of all S811 soft starters. For all units, if power is removed from the permissive circuit at any time, the unit will initiate a stop sequence, including a soft-stop if enabled.
MN03902002E
3-17
Note: With level sensing control, if +24V DC is removed from the permissive circuit at any time, the unit will initiate a stop and restart when +24V DC is reapplied to terminal P if: a) +24V DC is still available on pin 1 (to start from Terminal Block, Input #3 must also be enabled), b) the device shows a green status light (not faulted), and c) the Reset Mode parameter is set to AUTO on Digital Interface Module (DIM). See the Edge and Level Sensing sections below for more details. If the AUTO setting is used, CAUTION must be exercised to assure that any restart occurs in a safe manner. 4. Terminal 1 (Start mode) If terminal P is at +24V DC, momentary application of +24V DC to terminal 1 will initiate a start sequence for all S811 soft starters. Note: With level sensing control, if +24V DC is maintained on terminal 1 (Start) and removed from the permissive circuit at any time, the unit will initiate a stop. The unit will restart on application of +24V DC to terminal P if: a) +24V DC is still available on pin 1 (to start from Terminal Block, Input #3 must also be enabled), b) the device shows a green status light (not faulted), and c) the Reset Mode parameter is set to AUTO on Digital Interface Module (DIM). See the Edge and Level Sensing sections below for more details. If the AUTO setting is used, CAUTION must be exercised to assure that any restart occurs in a safe manner. Edge Sensing Edge sensing is set with the Start Control parameter. Edge sensing requires +24V DC power be momentarily applied to pin 1 (with terminal P at +24V DC) to initiate a start under all conditions. After a stop or fault occurs, the +24V DC must be removed, then reapplied to pin 1 before another start can occur. This control conguration should be used when restarting of the motor after a fault or stop must be supervised manually or as a part of a control scheme. The cycling of +24V DC power to terminal 1 before starting is required regardless of the setting of the Reset Mode parameter. Level Sensing Level sensing is set with the Start Control parameter. Level sensing will enable a motor to restart after a fault is cleared without cycling +24V DC power to terminal 1 as long as:
Terminal P is supplied with +24V DC (to start from Terminal Block, Input #3 must also be enabled), The Reset Mode parameter is set to AUTO, All faults have been reset.
3-18
MN03902002E
This control conguration should be used where it is desirable to restart a motor after a fault without additional manual or automatic control. An example of this condition would be on a remote pumping station where it is desirable to automatically restart a pump after a power outage without operator intervention. In the AUTO RESET MODE, CAUTION must be exercised to assure that any restart occurs in a safe manner. 5. Terminal 2 (Jog mode) If +24V DC power is applied to this terminal while terminal P is at +24V DC, the soft starter will operate in the jog mode as long as +24V DC is on terminal 2 and no faults occur. In jog mode, the soft starter will operate only on the thyristors and the bypass contactors will not close. 6. Terminal 3 (HAND/AUTO setting) Choose setting using the Reset Mode parameter on the DIM. 7. Terminal 4 (Reset) Application of +24V DC power will reset the soft starter after all fault conditions are cleared. If the AUTO setting is used with level control CAUTION must be exercised to assure that any restart occurs in a safe manner. See Edge and Level sensing on Page 3-18. 8. Terminals 13 and 14 (Programmable) At default setting, relay contacts for use up to 120V AC or 24V DC provide bypass contactor status. The contact closes upon bypass and will remain closed until a stop is initiated or a fault occurs. The motor and load may continue to rotate after a stop is initiated if soft stop is being used or if the load inertia is high. See Using an Auxiliary Relay section below for additional contact interface information. 9. Terminals 95, 96 and 98 (Programmable) At default setting, relay contacts for use up to 120V AC or 24V DC provide fault or ready status indication. See Page 3-13 for a description of their operation. Connecting a New or Replacement DIM When 24V DC is rst applied to terminals + and -, the S811 will send commands to the DIM to recongure its communication, and the S811 will send a reset to the DIM after conguration is done (this process takes approximately 20 seconds). Using an Auxiliary Relay The IT. Soft Starter contains one Form A and one Form C set of auxiliary contacts to indicate its status. A contact between terminals 13 and 14 indicates when the IT. is in bypass (unless it has been programmed to indicate another status). The contacts between terminals 95 and 96 and 95 and 98 indicate the IT. is in a normal or tripped state (unless it has been programmed to indicate another status). Often these contacts are used as shown in Figures 3-11, 3-12 and 3-13 with indicating lamps. In some installations the user may wish to use an electromagnetic relay for indication of the status at a remote location for use by a programmable controller (PLC), or in a 120V AC or 24V DC control circuit. If the IT. Soft Starter is subject to mechanical shock during operation, it is possible that these contacts may momentarily open, causing nuisance fault tripping of down stream devices. When used with an indicating lamp, a momentary contact opening would not be observed. In order to assure proper application, it is suggested that the following recommendations be followed:
MN03902002E
3-19
PLC Interface It is suggested that a 20 mS delay be programmed to assure the contact status before a change of status is indicated. The application and the environmental issues will determine the exact requirements. 24V DC Control When a relay is used in conjunction with an electronic control, it is highly recommended that a noise suppression/snubber diode be placed across the relay coil as shown in Figure 3-14. This diode offers two benets. First, the suppression of any electrical noise generated when the relay coil is de-energized. Second, the diode delays the opening of the relay slightly as it dissipates the energy stored in the relay coil. This delay is often long enough to compensate for the potential effects of a mechanical shock opening the control contact. A typical suppression diode is a 1N4001.
Figure 3-14: 24V DC Control 120V AC Control When a relay is used in conjunction with an electronic control, it is highly recommended that a noise suppressor be used across the relay coil. In the case of an AC coil, the noise suppressor is made up of a series connected resistor and capacitor as shown in Figure 3-15. Usually the delay in the relay opening is very small, so if the system is subject to shock, a delay should be added in the external control before the contact change of state is recognized. The resistor is rated 100 ohms at 0.5 watts. The capacitor is 0.25 F at 250V AC.
Figure 3-15: 120V AC Control Using a Supplemental Line Contactor In some installations, it may be necessary to use an electromagnetic contactor in series with the soft starter. In this case, it is recommended that the contactor be placed on the load side of the soft starter. The contactor must be closed prior to starting the soft starter and remain closed until the Soft Starter has been stopped to ensure proper soft starter and system operation.
3-20
MN03902002E
If an electromagnetic contactor is used on the line side of the soft starter, additional control circuitry must be supplied by the user when using edge level control to ensure the line power is supplied to the soft starter before control power (24V DC) is applied. If this sequence is not followed, the soft starter will fault on either a phase loss or zero voltage-crossing fault. This control scheme is illustrated in Figure 3-16.
STOP 120V AC
START
24V DC
PP 1 AutoReset = ON L1
480V AC Mains
L2 L3
Figure 3-16: 24V DC Control with Edge Sensing If it is desired to place an electromagnetic contactor on the line side of the soft starter, when using level control, no additional control circuitry is required. A start can be completed when the line power is supplied to the unit after the control power (24V DC), providing the Reset Mode parameter is set to AUTO and the unit has a green light status with +24V DC on pin 1. The soft starter will not fault on either a phase loss or zero voltage-crossing faults. If the AUTO setting is used, CAUTION must be exercised to assure that any restart occurs in the safe manner.
MN03902002E
3-21
3-22
MN03902002E
Chapter 4 Specications
Environmental
Table 4-1: Environmental Specications
Item Temperature Range Operating Storage Elevation Specification -40F 122F (-40C 50C) -58F 158F (-50C 70C) Up to 6,600 ft. (2000m). Above 6,600 ft. (2000m), derate 0.5% per 330 ft. (100m) Functional to 95% non-condensing Any 3 15g in any direction 3g in any direction
Humidity Operating Orientation Pollution Degree IEC 60947-1 Shock Resistance Vibration Resistance
Physical
Table 4-2: Weight
Frame Size N R T&U V Weight of Unit 5.8 Lbs. (2.6 Kg) 10.5 Lbs. (4.8 Kg) 48 Lbs. (21.8 Kg) with lugs 41 Lbs. (18.6 Kg) without lugs 103 Lbs. (46.8 Kg) with lugs 91 Lbs. (41.4 Kg) without lugs
MN03902002E
4-1
CE Conformance
Table 4-4: EMC Immunity
Immunity Electrostatic Discharge IEC 61000-4-2 Electromagnetic Field IEC 61000-4-3 Fast Transient Bursts IEC 61000-4-4 1.2/50 S 8/20 S Surges IEC 61000-4-5 Conducted RF IEC 61000-4-6 50 Hz Magnetic Field IEC 61000-4-8 Voltage dips Interrupt IEC 61000-4-11 Emissions Radiated Conducted EN 55011, Class A EN 55011, Class A Severity Level 4 kV contact discharge 8 kV air discharge 10 V/m 80 1000 MHz 2 angles 2 kV, 5 kHz rep, 2 min intervals 2 kV Line to earth 1 kV Line to Line 1 minute intervals 10 V rms .15 80 MHz N/A 30% dip @10 mS 60% dip @100 mS 100% interrupt @5 S
1. The 24V DC power supply must be grounded. 2. Add ferrite, Fair-Rite #0444173551 to DC Power Leads and Control I/O Leads (all through one ferrite) at S811 with two passes through ferrite of the DC Power Leads, and a single pass through ferrite of the I/O Control Leads. 3. Add ferrite, Fair-Rite #0443167251 to Load Leads at S811 with two passes through ferrite.
4-2
MN03902002E
Catalog No. S811T__V3S devices are UL Listed and suitable for use on a circuit capable of delivering not more than 18 kA symmetrical amperes, 690 volts maximum, when protected by a Ferraz-Shawmut Amp-Trap Form 101 (Cat. No. A70QS800-4) 800 Amp, 700 Volt Semiconductor Protection Fuse. Catalog No. S811V__V3S devices are UL Listed and suitable for use on a circuit capable of delivering not more than 42 kA 690 volts maximum, when protected by a Ferraz-Shawmut Type PSC (Cat. No. A070URD73I1600) 1600 Amp, 700 Volt Semiconductor Protection Fuse. Catalog No. S811T__V3S devices tested per IEC 60947-4-2 to Type 1 Short Circuit Withstand Requirements to 18 kA, 690 volts with Cutler-Hammer Cat. No. NW3800T33W 800 Amp 690 Volt circuit breaker. Catalog No. S811V__V3S devices tested per IEC 60947-4-2 to Type 1 Short Circuit Withstand Requirements to 42 kA, 690 volts with Cutler-Hammer Cat. No. RW420T33W 2 kA 690 Volt circuit breaker.
Note: Short circuit protection must be applied on the line side of the soft starter.
MN03902002E
4-3
4-4
MN03902002E
T3
L2
T2
Motor
L1
T1
Figure 5-1: Soft Starter SCRs For each start, the length of time the SCRs are conducting current as well as the magnitude of that current determine how hot the SCRs will get. Between successive starts the SCRs must cool down to avoid exceeding their thermal limits. Appendix C (Ratings, Cooling and Power Losses) gives the S811s application ratings for various starting conditions. Staying within these specied limits should avoid over temperature trips. When the S811 control circuit senses that the internal temperature has increased above a preset value, internal fans are tuned on to assist in cooling. To maximize fan life the fans are only turned on when needed. Further discussion of fan operation can be found in Appendix C.
Control
The software contained in the S811 IT. Soft Starter is the heart of the product. This software allows you to control nearly every aspect of the soft starters functionality. In this section, various features and protection options are described. Note: In the following descriptions the S811 Parameter Names are shown in italics. You will nd a complete listing of these parameters in Appendix A. Note that the motor current measurements made with a standard meter may not be correct because of the non-sinusoidal nature of the current during starting. The S811 is designed to accurately measure these currents so that the current displayed by the S811s Digital Interface Module (DIM) is correct.
MN03902002E
5-1
Starting Options The following starting choices are available in the S811 IT. Soft Starter: Voltage Ramp Start This is the most commonly used mode of soft starting. Starting at an initial value set by the Initial Torque parameter, the voltage applied to the motor is gradually increased at a rate that will reach rated voltage at time tr, set by the Soft Start Time parameter. As the voltage increases the motor develops torque that accelerates the load toward full speed. When the S811 senses that the motor has come up to speed, it quickly completes the voltage ramp and closes the bypass contactor. See Figure 5-2. It should be noted that a lightly loaded motor takes less torque, and thus lower voltage and time, to accelerate to full speed. For this case the S811 will go into bypass before the ramp reaches full voltage. In other words, the S811 will go into bypass before the Soft Start Time has elapsed.
Bypass Voltage Ramp Kick Start Torq Rated Voltage 100% Bypass
Torque
Initial Torque
Soft Start Time tr Kick Start Time Start Run Time (Seconds)
Speed
100%
Run
Figure 5-2: Ramp Start Kick Start The Kick Start feature works in both the Voltage Ramp Start and Current Limit Start modes. By momentarily applying a pulse of current to the motor, it provides an initial boost in torque to overcome the static friction common in some applications. The level of torque boost is set by the Kick Start Torq parameter and the duration of the kick is set by the Kick Start Time. Setting the Kick Start Time to 0 disables this feature.
5-2
MN03902002E
Current Limit Start This mode is typically used when it is necessary to limit the maximum current during start-up due to line power limitations or other considerations. During a Current Limit Start the S811 applies a constant voltage to the motor, resulting in limited current owing through the motors windings. The level of current is set by the Initial Torque parameter. See Figure 5-3. Note: Current Limit Starts are not recommended on variable torque load applications like fans and pumps.
Bypass Kick Start Torq Initial Torque Current 100% Speed 100%
Bypass
Soft Start Time Kick Start Time Start Run Time (Seconds)
Run
Figure 5-3: Current Limit Start Soft Stop This feature is used for applications that require a controlled extended stop. It is designed for high frictional loads that tend to stop suddenly when voltage to the motor is removed. During Soft Stop the voltage is gradually reduced to zero in the time set by the Soft Stop Time parameter. See Figure 5-4. Note: The Soft Stop mode is not an electronic brake function and will not stop a motor any faster than it would normally take to coast to a stop under load.
100%
Speed
Figure 5-4: Soft Stop Pump Start/Stop (Optional) This pump control option is described in Appendix E.
MN03902002E
5-3
Protection
Thermal Overload The IT. S811 Soft Starter features an electronic motor overload protection feature. It is designed to protect the motor and power wiring against overheating caused by operating at excessive current levels for extended periods of time. Entering the motors full load current rating, using the Overld Trip FLA parameter programs the overload. The Overld Trip FLA is settable from 32% to 100% of the S811s rated current. The overloads trip class is set using the Ovrld Trip Class parameter. Additional details on the Thermal Overload can be found in Appendix B. S811 and Motor Protection In addition to motor overload protection, the S811 has many programmable features designed to protect the motor as well as the soft starter itself.
Incoming Line Phase Reversal, Loss, Imbalance, Over Voltage, and Under Voltage trips Three Overcurrent trips Stall and Jam trips
For troubleshooting purpose trips are recorded, as they occur, in the S811s Fault Queue.
5-4
MN03902002E
Chapter 6 Conguration
Programming the S811
A Digital Interface Module (DIM) is used to congure all models of the IT. S811 Soft Starter.
The Status Bar at the top of the display indicates the operating and communicating status of the S811 and DIM. The three Soft Key Functions at the bottom of the display indicate the functions of the Soft Keys (pushbuttons) directly below them. The Soft Key Functions will change as you navigate through the different menus of the DIM. The center of the display shows the value of the selected S811 parameter. The default display at power-up is 3 Line Currents. Figure 6-1 show how the S811s parameters are organized within the menu structure. Navigating through the menus down to the parameters is straightforward if you understand a few basic concepts. 1. The Escape Key (ESC) moves you from the User Display to the Parameter Edit Screen. 2. The PREV and NEXT soft keys (Figure 6-2) scroll from menu to menu (left and right). 3. The far right soft key will allow you to take action (Enter, Edit, More, Send, ) to drill down into the menu or parameter. 4. When you enter a menu, the Previous and Next soft keys scroll from parameter to parameter (up and down) in that menu. 5. The Escape Key backs you out of the current parameter or menu.
ONLN SS OXFDO1 H STOP 3 Line Currents XXXX L1 Amp XXXX L1 Amp XXXX L1 Amp
JOG RESET H->A
Status Bar
MN03902002E
6-1
Status Bar
PREV
NEXT
ENTER
Figure 6-2: Digital Interface Module (DIM) Parameter Edit Mode For a more complete description of the DIM, refer to Appendix F.
OL Trip Class Kick Start Torque Initial Voltage Ramp Torque Current Limit Torque Voltage Start Ramp Time
Trip Class T1
Kick Start Time Sec Initial Torque Initial Torque % rated pullout torque % rated pullout current
tr
6-2
MN03902002E
ts
ts
Sec
Protections Menu Overload Jam Stall Phase Loss Phase Imbalance Phase Sequence Reversal Fault Reset Special Function Ramp / Current Ramp Start Limit Start Option Conguration Menu Option Edge/Level Start Input S811 DIM parameter Start Control Default Level Sets whether the Start input at the terminal block responds only when it sees a transition from 0 to +24V DC (edge) or anytime 24V DC is present (level) Start Method Overload Jam Stall Ph. Loss Ph. Rev Ovld Fault Jam Fault Stall Fault Phase Loss Fault Phase Imb Fault Phase Rev Fault See also Phase Sequence
Man/Auto Reset
Reset Mode
MN03902002E
6-3
6-4
MN03902002E
Setup
After all power and control connections have been made and you have read and understood the different operating modes and protection features (Chapter 5) of the soft starter, it is time to program it for your application. The following procedure will take you through the setup of the S811 to match it to your motor and application, bumping the motor to verify correct direction of rotation, and tuning of the selected operating mode. After this procedure has been completed, it is suggested that you review the Protection Options of the S811 (Appendix B) and select the appropriate ones for your application. All Protection Options are shipped from the factory enabled. As shipped from the factory, the S811 Soft Starters default conguration is sufcient for basic operation but may require some conguration to tune it for your application. The following procedure assumes you understand how to navigate through the S811s parameter menu using the Digital Interface Module (DIM) and that the S811 is in its Factory (Out-of-Box) state. Refer to Appendix F of this manual for a detailed explanation of DIM operation.
MN03902002E
7-1
Initial Conguration: 1. It is suggested that the S811 Soft Starter be congured before applying the line voltage. Before applying the Line voltage, apply 24V DC to the + and - connections of the S811s terminal block. Eaton Cutler-Hammer will be displayed by the DIM while the S811 is powering up. When power-up is complete the DIM should be displaying 3 Line Currents. Note: If anything else is displayed, go to Chapter 8, Troubleshooting, for information on getting the S811 back to a known state. 2. Using the DIM, review the parameter settings in the Conguration and Protections menus. Parameter navigation and menus are located in Appendix A and F. The following setup procedures will use the factory default settings unless changed by you. 3. In the Conguration menu, set the Overld Trip FLA parameter to the motors nameplate rated current. This setting assumes the motor has a 1.15 Service Factor. 4. Set Ovrld Trip Class parameter for the desired overload trip characteristic (curve). 5. In the Protections menu set the Motor Rated Volt parameter to the motors operating voltage. 6. If auto fault reset is required, set the Reset Mode parameter to Auto (and Start Control to Level (default)). NOTE: Auto Reset is intended for unattended installations where there is no danger to personnel or other equipment when the motor starts without warning. If Auto Reset is enabled, CAUTION must be exercised to assure that any restart occurs in a safe manner. 7. Apply the Mains voltage and verify that no fault is present. If a fault is indicated, display the Motor Control menus Application Status parameter to determine the source of the fault. Each fault is described on Page 8-6. a. A Phase Reversal Fault is a likely candidate on new installations. It can be remedied by either changing the Phase Sequence parameter from ABC to ACB or removing Mains power and switching the incoming line connections at L1 and L2 of the S811.
8. Quickly Jog (bump) the motor just enough to verify that the direction of rotation is correct. If it is not, remove all power to the S811 and the motor and swap two of the motors winding connections. 9. Based on the desired starting mode, Voltage Ramp or Current Limit, complete the conguration of your S811: a. Voltage Ramp Start Conguration i. Initial parameter settings: Start Method = Voltage Ramp. Initial Torque = 50% Soft Start Time = 60 sec Kick Start Torq = 0% (fans and pumps), 75% (high breakaway loads) Kick Start Time = 0 sec (fans and pumps), 1 sec (high breakaway loads) Soft Stop Time = 60 sec Start the motor and determine the worst case starting conditions. Adjust Initial Torque for smooth start without hesitation. Rotation should begin within 2 seconds.
ii.
7-2
MN03902002E
iii. If Stall Faults occur at the end of the ramp time, increase Initial Torque, Kick Start Torq & Time and/or Soft Start Time to get into bypass before the Soft Start Time elapses. Also, verify that the motor is not overloaded. iv. Adjust the Soft Stop Time for the desired stopping time. b. Current Limit Start Conguration v. Initial settings: Start Method = Current Limit Initial Torque = 50% Soft Start Time = 120 sec Kick Start Torq = 0% Kick Start Time = 0 sec (disabled) Soft Stop Time = 60 sec
vi. Start the motor and determine the worst case starting conditions. Adjust Initial Torque for smooth start without hesitation. Rotation should begin within 2 seconds and the motor should smoothly accelerate to full speed. vii. If Stall Faults occur, increase Initial Torque and/or Soft Start Time to get into bypass before the Soft Start Time elapses. Also, verify that the motor is not overloaded. viii. After suitable performance has been achieved, determine the starting time to bypass and set Soft Start Time at 1.25 times this time. For example, if it takes 10 seconds to accelerate the motor and go into bypass, set the Soft Start Time for 12.5 seconds. ix. Adjust the Soft Stop Time for the desired stopping time. 10. Review the Protection Options of the S811 and congure the appropriate ones for your application. Refer to Table A-4 on Page A-5 for the list of parameters used in conguring the protections features on your S811 Soft Starter. These parameters are located in the Protections menu of the DIM. 11. The S811 can be operated from a remote automated network. For network conguration details refer to Appendix G of this manual.
12. Refer to Appendix H of this manual for additional details on each of the S811s software parameters. 13. For additional support contact Customer Support.
MN03902002E
7-3
7-4
MN03902002E
Chapter 8 Troubleshooting
General
In this section of the manual, we present a procedure you can follow to diagnose a problem with your S811. While many potential situations are outlined in this section, it is possible you may run into a problem that is not covered here. If you have worked through the following troubleshooting procedure and nd that you require further assistance, please contact Eaton. Please have the following information ready when you call:
Order No. (if available): Catalog Number: Style Number: Serial Number:
Avertissement
Bien lire et comprendre les procdures contenues dans ce manuel avant de tenter le fonctionnement ou la mise en place de lquipement.
Advertencia
Asegrese de leer y entender los procedimientos en este manual antes de intentar operar o congurar el equipo.
We highly recommend that you read this entire section of the manual before you begin to troubleshoot the IT. Soft Starter. You may want to obtain the following equipment to aid you in troubleshooting:
Always assume the S811 has high voltage applied and take proper precautions while troubleshooting the soft starter and associated equipment. Read all precautions at the front of this manual before starting the troubleshooting process.
MN03902002E
8-1
The S811 Soft Starter can not be started until all faults have been reset. If a fault condition persists, fault reset is not possible and the Status LED remains red. Also, a local start requires that the start source (DIM, terminal block, Cover Control or other similar device) be in HAND mode (L bit in Motor Control Byte = 1). Pressing the START button on the DIM automatically puts that device in HAND.
Start
No
Yes
Green
Red
End
Figure 8-1: Start Command Troubleshooting Flowchart a. Check the 24V DC power supply for proper operation. Is the 24V power supply connected to the proper power source? Measure the 24V DC at the output terminals and on the soft starter input terminals. Check the screw terminal connections and polarity of the wiring. See Troubleshooting Status LED OFF, Table 8-2.
8-2
MN03902002E
b.
With the status LED red, the device will not start. Attempt to reset the S811 Soft Starter by pressing the S811s recessed RESET button for one second or pressing the RESET soft key in the Display Mode screen of the DIM. If the LED remains red, use the DIM to determine the fault code and go to the Troubleshooting Fault Table, Table 8-4, to nd the corrective action for each fault code. The LED is green and the S811 Soft Starter is ready to start. Find the Start source in Table 8-1 to determine the appropriate corrective action. Verify that the P input terminal is at 24V DC. Then try to start the S811 using the DIM.
Suggested Corrective Action Verify the P (Permissive) input terminal is at 24V DC, either hard wired or wired through a normally closed STOP button. Verify no other motor control device is preventing a start by clearing its permissive bit. Disconnect any other QCPort device that may prevent a start and purge them from the S811s device list. This takes these devices out of the system and simplies troubleshooting. Verify the P input terminal is at 24V DC when the start is attempted. Verify the 3 input terminal is at 24V DC when start is attempted. Verify 24V is applied to the 1 input terminal when the start is attempted. If the Start Control parameter is set to Edge, verify the 1 input terminal sees a transition from 0V to 24V after all faults have been reset and the above conditions have been veried. Verify no other motor control device is holding its permissive at 0. If it is, force its permissive = 1 or temporarily remove it from the S811 and purge it from the S811s device list.
c.
Other QCPort Motor Control Remove all external QCPort devices, purge them from the S811s device list and attempt a start from the DIM. If the start is not Node successful, see DIM category above. Once that start is successful, reattach QCPort device(s) and retry start. Fieldbus (DeviceNet, Probus, etc.) Determine if the S811 can be started locally using the DIM. Verify that the S811 was in AUTO when the eldbus start was attempted (all motor control devices having their L bits = 0). Verify no other motor control device is asserting its permissive (bit = 1). If it is, force its permissive = 1 or temporarily remove it from the S811 and purge it from the S811s device list.
Unplugging any source of motor control from QCPort will require that it be purged from the S811s motor control command device list (press and hold the S811s recessed RESET button for six seconds).
2. The S811 Soft Starter trips during starting and never reaches bypass. Use the DIM to determine the App Status fault code and go to the Troubleshooting Fault Table, Table 8-4, to nd the corrective action for each fault code. 3. The S811 Soft Starter trips during running operation while bypass contactors are engaged. Use the DIM to determine the App Status fault code and go to the Troubleshooting Fault Table to nd the corrective action for each fault code. 4. The S811 Soft Starter trips after the stop is commanded. Use the DIM to determine the App Status fault code and go to the Troubleshooting Fault Table to nd the corrective action for each fault code. 5. The S811 Soft Starter stops sooner than expected during a soft stop. If the Soft Stop Time is set too long for the motor loading, the motor will begin to stall when delaying SCR ring reduces the voltage. The S811 Soft Starter will detect this stalling and end the stop immediately and not set any faults.
MN03902002E
8-3
Start
No
Yes
Off
Red
No
Green
No
Yes Consult Status LED GREEN Table, Table 8-3 Depress either RESET Button
No
Yes
Yes Reset the Node ID, Baud Rate, and Mode on Channel 0. Consult Resetting the S811 Table
No Consult Fault Table Is the DIM connected and Communicating to the S811? No
Yes
After 30 seconds, did the DIM reconnect to the S811? Yes Go to Start
No
End
8-4
MN03902002E
Status LED never illuminates but Port 0 and Port 1 LEDs are actively ashing
Communications Firmware failure. Status LED and Port 1 LED never illuminate, Port 0 LED is constantly illuminated Port 0, Port 1 LEDs never illuminate, Status LED illuminates
LED failure, communication failure S811 may still operate properly on the Port. with a non-operational LED. Possible fatal device failure.
Status LED green but S811 is Terminal block Hand input is low. not responding to Start from eld wiring
Status LED green but S811 is 24V is not being applied to the eld Verify if the soft starter is not responding to Start from wiring Start, Jog or Permissive congured for Level sensitive or eld wiring terminal. Edge sensitive eld wiring. If commanding Start or Jog with Level Sensitive Inputs: Check eld wiring. Make sure terminal P, terminal 1, and terminal 3 have 24V applied. If commanding Start with Edge Sensitive inputs: Make sure terminal 1 cycles from low to high while P and terminal 3 remain high. Status LED green but S811 is A network device or eld wiring is not responding to Start from holding permissive low. eld wiring, DIM or network Make the eld wiring permissive on the S811 and any cover controls are at 24V. Verify all hand control devices are sending permissive. A 0V permissive on any motor control device will inhibit a start or stop a running motor.
MN03902002E
8-5
Fault Codes
Table 8-4: Troubleshooting Fault Table
Fault Code Possible Problem 1 3 Firmware Incompatibility or Hardware failure. Interdevice Communications Fault Communications to DSP have been interrupted. Possible electrical noise or hardware failure. Low Control Voltage Fault The external 24V power supply voltage is dropping below the minimum required to control the motor. Possible Solution Call Eaton support. Try a 24V DC control voltage power cycle to attempt to clear problem. Verify that the S811 is properly grounded. Call Eaton support if the problem persists. Use recommended 24V power supplies with enough current sourcing capability to close contactors. Verify correct wire size used to connect power supply to S811. (See power supply specication for more details.) Verify connections are secure. Ventilate to specied maximum temperatures, clear obstructions, verify fans are operational, verify control system is not exceeding the specied maximum starts per hour.
Device Over Temperature Fault A temperature sensor has indicated excessively high temperature. Operating environment above specied maximum temperature, ventilation holes blocked, fans are not operational, starts per hour exceed specications, sensor failure on circuit board. Phase Loss Fault Extreme phase imbalance condition. Incoming phase disconnected, blown fuse. Phase Imbalance Fault The imbalance of the incoming phases exceeds the trip threshold.
Correct imbalance problem with mains. Increase the xx Imbalance Fault xx parameters or disable the fault if the other issues cannot be resolved. Make sure your system can tolerate the imbalance. Repair/replace broken belts, linkage, or clutch, and/or increase load. Reduce Low I Trip % FLA to an acceptable value (0% will disable).
Under Load Fault Current supplied to the motor is below trip threshold. Linkage or belt driven by motor is broken, a clutch or other load engagement device is not operating, the motor is not loaded to the trip current.
10
Over Current Fault only active in bypass if the Disconnect power from S811 and any other Jam Fault is disabled. Current exceeds the fault equipment. Remove obstruction in motor drive threshold. train. Verify S811 is properly sized for the application. Jam Fault While in bypass an obstruction has Disconnect power from S811 and any other slowed or stalled the motor resulting in equipment and remove obstruction. Jam Fault can be disabled if trips occur during normal extreme motor current. operation. Over Current Fault will provide protection at a higher current threshold. Bypass Failure Fault S811 detected that the Verify control power and wire size meets Bypass contact(s) not closed. Possibly opened specications. Reduce shock or vibration. Call due to excessive shock or 24V DC control Eaton support if the problem persists. voltage sag (insufcient voltage to maintain contact closure). Overload Fault Motor has been overloaded for an extended period of time. Reduce the motors load. Increase Overld Trip FLA and/or Ovrld Trip Class if the overloads are infrequent and the motor & system can tolerate them. Note: Exceeding nameplate ratings will shorten equipment life.
11
13
14
8-6
MN03902002E
32 36
Nonvolatile Ram Fault Internal memory error. Call Eaton support. Motor Control Command Communication Lost Reattach network controller, replace connection cable. Call Eaton support if the Fault Communications to a network controller was lost while motor was running. problem persists. Device was disconnected or the connection broken. Temperature Sensor Fault Temperature sensor or interconnection failure. Watchdog Fault Firmware Incompatibility or Hardware failure. Call Eaton support. Fault can be disabled, but S811 will not be protected against failures caused by excessive internal temperatures. Call Eaton support.
38
39 42
Under Voltage Fault Incoming AC line voltage Connect to correct supply voltage. Verify Motor below trip threshold. Device connected to Rated Volt is set to correct value. It may be incorrect mains supply voltage. necessary to reduce this setting for soft mains. Over Voltage Fault Incoming AC line voltage above trip threshold. Device connected to incorrect mains supply voltage. Connect to correct supply voltage. Verify Motor Rated Volt is set to correct value. It may be necessary to increase this setting for high mains.
43
44
Motor Voltage Phase Reversal Fault incoming Set Phase Sequence to match incoming line phase rotation sequence opposite of sequence. If motor is turning in wrong device setting. direction swap two motor connection leads. If mains leads need to be changed, swap incoming leads and set Phase Sequence to match incoming sequence. If an upstream reverser is used, disable Phase Rev Fault. Motor Control Command Device Missing Fault Re-attach motor control command device and A motor control command device (DIM, reset the fault. If the motor command device is Cover Control, or similar device) was removed. to be permanently removed, purge it from the S811s motor control command device list (press and hold the recessed RESET button on the front of the S811 for six seconds). The STATUS LED will change to amber when the action has started and any detached motor control device has been removed from the S811s list. Interdevice Communication Fault Communication between the S811s internal control devices was interrupted. Program CRC Fault one or more internal memory locations have been corrupted. Call Eaton support.
55
56
57 58
Cycle 24V DC power to the S811. Call Eaton support if fault persists.
SCR Not Firing Fault SCR is not conducting Re-apply lost phase. Review S811 application. when gated. Incoming phase lost. Special Call Eaton support if problem persists. application undersized or high impedance motor, SCR malfunctioning, circuitry damaged by megger testing. Shorted SCR fault SCR is shorted from over current abuse, bypass contactor welded shut, application/conguration issues. Call Eaton support if problem persists.
59
MN03902002E
8-7
SCR Over Current Fault Excessive SCR Increase Soft Start Time and/or Initial Torque. Current prior to bypass. Only active when Stall Reduce starting load. Verify S811 is properly Fault is disabled. Motor should be up to speed sized. prior to bypass. Mains AC Voltage Loss Fault fuses blown, disconnect open, or breaker tripped. Motor Stall Fault current too high at the end of Soft Start Time to enter bypass. Voltage Zero Cross Lost Fault Mains lost, phase L1 or L3 lost. Replace fuses, close disconnect, or reset breaker. Lengthen Soft Start Time and/or increase Initial Torque. Reduce starting load. Verify S811 is properly sized. Restore mains or lost phases. Call Eaton support if problem persists.
61 63
64
8-8
MN03902002E
Service
For additional information on this product, please call our Customer Support Center at: 1-800-356-1243 or visit our web site at: www.EatonElectrical.com. For technical assistance, please contact the Technical Resource Center at (800) 809-2772. Service and repair is available from Eaton or several factory authorized regional service centers. Please contact Eatons Product Integrity Center at (800) 345-0434 for the location nearest to you. For eld service or start-up assistance 24 hours a day, 7 days a week, please call (800) 498-2678.
MN03902002E
9-1
9-2
MN03902002E
Appendix A Parameters
Parameter List
User Display Mode
ONLN SS OXFDO1 H STOP 3 Line Currents XXXX L1 Amp XXXX L1 Amp XXXX L1 Amp
JOG RESET H->A
NEXT
PREV
ESC
THEN
OR
OR
ESC
ESC
PREV
NEXT
ENTER
PREV
NEXT
ENTER
PREV
NEXT
ENTER
PREV
NEXT
ENTER
PREV
NEXT
ENTER
PREV
NEXT
ENTER
PREV
NEXT
ENTER
ESC
ESC
ESC
ESC
ESC
ESC
ESC
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
ESC
ESC
ESC
ESC
ESC
ESC
ESC
Parameter List
Parameter List
Parameter List
Parameter List
Parameter List
Parameter List
MN03902002E
A-1
Monitoring Menu
To User Display Mode
ESC
PREV
NEXT
ENTER
NEXT
ESC
ENTER
ESC
Access Level 0 0 0 0 0 0 0 0 0 0 0
Note:
The button under the PREV Soft Key moves up one line.
NEXT
The button under the NEXT Soft Key moves down one line.
A-2
MN03902002E
ESC
To Monitoring Menu
PREV
PREV
NEXT
ENTER
NEXT
To Configuration Menu
ESC
ENTER
ESC
Units
Access Level 0 0 0 0 3 3
Note:
The button under the PREV Soft Key moves up one line.
NEXT
The button under the NEXT Soft Key moves down one line.
MN03902002E
A-3
Conguration Menu
To User Display Mode
ESC
PREV
PREV
NEXT
ENTER
NEXT
To Protections Menu
ESC
ENTER
ESC
Units Amps
Min 12 5 0
Access Level 2 2 2 2 2 2 2 2 2 2 3 3 3
0.5 0 0 0 0 30 Edge 0 0 0
Note:
The button under the PREV Soft Key moves up one line.
NEXT
The button under the NEXT Soft Key moves down one line.
A-4
MN03902002E
Protections Menu
To User Display Mode
ESC
To Configuration Menu
PREV
PREV
NEXT
ENTER
NEXT
ESC
ENTER
ESC
Units
Min Disable Disable 0 Disable Disable Disable 1 0.1 Disable 1 0.1 1 0.1 Disable ABC Manual Disable Disable Disable Disable 1 0.1 Disable 101 0.1 115
Max Enable Enable 100 Enable Enable Enable 100 60 Enable 100 60 100 60 Enable ACB Auto Enable Enable Enable Enable 99 60 Enable 120 60 690
Default Enabled Enabled 6 Enabled Enabled Enabled 80 0.5 Enabled 40 0.5 6 0.5 Enabled ABC Manual Enabled Enabled Enabled Enabled 90 3 Enabled 110 3 480
Access Level 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2
Note:
The button under the PREV Soft Key moves up one line. The button under the NEXT Soft Key moves down one line.
NEXT
MN03902002E
A-5
ESC
To Protections Menu
PREV
PREV
NEXT
ENTER
NEXT
ESC
ENTER
ESC
Units
Min Disable 0 0
Max Enable 6 4
Default Disabled
Access Level 3 3 3 3 3 3 3
mSec mSec
mSec mSec
2000 2000
3 3 3
A 0 setting will disable this feature until the next factory reset.
Note:
The button under the PREV Soft Key moves up one line.
NEXT
The button under the NEXT Soft Key moves down one line.
A-6
MN03902002E
ESC
PREV
PREV
NEXT
ENTER
NEXT
ESC
ENTER
ESC
Access Level 0 0 2 3 3 3 3 3 3 3 3
Note:
The button under the PREV Soft Key moves up one line.
NEXT
The button under the NEXT Soft Key moves down one line.
MN03902002E
A-7
ESC
PREV
PREV
NEXT
ENTER
ESC
ENTER
ESC
A-8
MN03902002E
Units
Min
Max
Default
Access Level 2 0 2 3
Secs mSec
3 3 3 0 1 2 2 3 3 3 0 2 2 0 2 2 0 3 3 2
Secs Secs
0 0
65535 30
0 0
0 3 3 0 0
Note:
The button under the PREV Soft Key moves up one line.
NEXT
The button under the NEXT Soft Key moves down one line.
MN03902002E
A-9
A-10
MN03902002E
Appendix B Protection
Thermal Overload
The IT. Soft Starter features an electronic motor overload protection feature. This is intended to protect the motor and power wiring against overheating caused by excessive current for extended periods of time. Note: Short circuit protection must be applied on the line side of the soft starter. Entering the motor full load current rating, using the Overld Trip FLA parameter programs trip current. It is programmable from 32% 100% of the units rated current. Table B-1: Overload Adjustment Settings
Frame Size N R T Catalog Number S811N37N3S S811N66N3S S811R10N3S S811R13N3S S811T18N3S S811T18V3S S811T24N3S S811T24V3S S811T30N3S S811T30V3S U S811U36N3S S811U42N3S S811U50N3S V S811V36N3S S811V36V3S S811V42N3S S811V42V3S S811V50N3S S811V50V3S S811V65N3S S811V65V3S S811V72N3S S811V72V3S S811V85N3S S811V85V3S S811V10N3S
See Application Notes, Appendix D.
FLA Current Range 11 37 20 66 32 105 42 135 56 180 75 240 95 304 112 360 131 420 156 500 112 360 131 420 156 500 203 650 225 720 265 850 320 1000
Note: Overload Trip FLA parameter is settable to any point within its range.
MN03902002E
B-1
The thermal overload is designed to protect the motor from overheating caused by excessive current. If the motor is overloaded, the current drawn rises and heats the motor. The FLA sets the trip threshold and the trip class (5 to 30) is set with the Ovrld Trip Class parameter. If the device trips on a thermal overload, an internal timer is started which inhibits a reset for three minutes. After this timer expires, the device may be reset and the thermal fault is cleared. At this point another internal timer is started, this timer is 26 x 3 or 48 minutes. If another trip occurs before this timer expires, the reset inhibit time is increased to 96 minutes. Once the trip level reaches 3, it will take 144 minutes to go back to level 2, then 96 minutes to get back to level 1. To get from level 3 to a reset thermal overload at level 1, it takes 240 minutes without a trip. A reset thermal overload at level 1 means the next thermal overload trip will have a 3-minute reset inhibit as in Table B-2. Table B-2: Thermal Motor Overload Times
Trip Level 1 2 3 Reset Inhibit Time 3 minutes 6 minutes 9 minutes
Total 240 minutes to reset to level 1.
Cycling power on the device will NOT clear the thermal trip. The thermal pile and the reset inhibit time are saved to the non-volatile memory. These values are reloaded when the device boots and the timer is restarted at the full reset time. This means if the 3-minute inhibit timer has been running two minutes, cycling power will require the user to wait the full three minutes before a reset can clear the overload fault. If the device is shut down when the overload fault is tripped, the temperature is also saved to the non-volatile memory. If the device is left to cool and then powered, the temperature read from the sensor is compared to the saved temperature. If the current temperature is 87% or less of the saved temperature, a full thermal pile rest is initiated.
B-2
MN03902002E
115%
Time (Seconds)
100.0
Class 30
Class 10
Class 20
Class 5 10.0
1.0 0 100 200 300 400 500 Percent FLA 600 700 800 900
MN03902002E
B-3
Instantaneous Over Current When the bypass contactors are not engaged, the S811 monitors the maximum RMS value of the three phase currents. The unit will trip with an instantaneous over current fault if the maximum value exceeds six times the catalog FLA setting for 1.5 seconds. This internal protection mechanism is most useful for protecting the S811 from starting motor too large for its ratings. Table B-4: Instantaneous Over Current Settings
Trip Trip Threshold Trip Delay DIM Parameter Not User Settable Not User Settable Set Point 6x catalog FLA 1.5 Seconds Default N/A N/A
Motor Stall The S811 monitors the maximum RMS value of the three phase currents. The unit will trip with a motor stall fault if the stall fault is enabled and the maximum RMS value exceeds two times the FLA setting when the start time setting expires. Table B-5: Motor Stall Settings
Trip Trip Enable Trip Threshold DIM Parameter Stall Fault Not User Settable Set Point {On, Off} 2x FLA Default On N/A
SCR Over Current The SCR over current trip is only active if the stall fault trip is disabled. The S811 monitors the maximum RMS value of the three phase currents. The unit will trip with a SCR over current fault if the stall fault is enabled and the maximum RMS value exceeds three times the FLA setting when the start time setting expires. Table B-6: SCR Over Current Settings
Trip Trip Threshold DIM Parameter Not User Settable Set Point 3x FLA Default N/A
B-4
MN03902002E
Motor Jam When the bypass contactors are closed, the S811 monitors the maximum RMS value of the three phase currents. The unit will trip with a motor jam fault if the jam trip is enabled and the maximum RMS value exceeds three times the FLA setting for 1.5 seconds. Table B-7: Motor Jam Settings
Trip Trip Enable Trip Threshold Trip Delay DIM Parameter Jam Fault Not User Settable Not User Settable Set Point {On, Off} 3x FLA 1.5 Seconds Default On N/A N/A
Motor Over Current The motor over current trip is active only if the jam fault trip is disabled. When the bypass contactors are closed, the S811 monitors the maximum RMS value of the three phase currents. The unit will trip with a motor over current fault if the maximum RMS value exceeds four times the catalog FLA for the class dependent trip delay. Table B-8: Motor Over Current Settings
Trip Trip Threshold Trip Delay Class 5 Class 10 Class 20 Class 30 DIM Parameter Not User Settable Not User Settable Set Point 4x Catalog FLA 2.0 seconds 4.0 seconds 6.0 seconds 8.0 seconds Default N/A N/A
Motor Under Load The S811 monitors the average value of the three phase currents as a percent of FLA. The unit will trip with a motor under load fault if the percent FLA value falls below the trip threshold for greater than two seconds. Table B-9: Motor Under Load Settings
Trip Trip Threshold Trip Delay DIM Parameter Low I Trip % FLA Not User Settable Set Point 1 100% 2.0 Seconds Step 1% N/A Default 6% N/A
Phase Imbalance Current NEMA dened current imbalance is calculated using the following equation: Percent Imbalance = 100 * (max deviation from average / average) The S811 monitors the current imbalance when the motor is running. The unit will trip with a motor phase imbalance fault if the current imbalance trip is enabled, the percent imbalance exceeds the trip threshold for the trip delay and the current is greater than the FLA trip setting. Table B-10: Current Imbalance Settings
Trip Trip Enable Trip Threshold Trip Delay DIM Parameter Phase Imb Fault I Imbal Trip Lev I Imbal Dly Set Point {On, Off} 1 100% 0.0 60.0 Seconds Step N/A 1% 0.1 Second Default On 40% 0.5 Second
MN03902002E
B-5
Phase Loss NEMA dened current imbalance is calculated using the following equation: Percent Imbalance = 100 * (max deviation from average / average) The S811 monitors the current imbalance when the motor is running. Phase loss is an extreme case of current imbalance. The unit will trip with a motor phase loss fault if the phase loss trip is enabled, the percent imbalance exceeds the trip threshold for the trip delay and current increases above FLA trip setting. Table B-11: Phase Loss Settings
Trip Trip Enable Trip Threshold Trip Delay DIM Parameter Phase Loss Fault Phase Loss % Trp Phase Loss Dly Set Point {On, Off} 1 100% 0.0 60.0 Seconds Step N/A 1% 0.1 Second Default On 80% 0.5 Second
Motor Voltage Phase Reversal The S811 monitors the phase voltages to determine the incoming phase sequence (ABC or ACB). If the monitored sequence differs from the Incoming Phase Sequence parameter setting, a motor phase reversal fault is issued. The phase reversal trip will need to be disabled when using an upstream reverser. Table B-12: Motor Voltage Phase Reversal Settings
Trip Trip Enable DIM Parameter Phase Rev Fault Step {On, Off} Default On
Phase Imbalance Voltage NEMA dened voltage imbalance is calculated using the following equation: Percent Imbalance = 100 * (max deviation from average / average) The S811 monitors the voltage imbalance when the motor is off and checks the value just prior to starting to determine if a fault shall be issued. The unit will trip with a motor phase imbalance fault if the phase imbalance trip is enabled and the percent imbalance has exceeded the trip threshold for the trip delay. Table B-13: Voltage Imbalance Settings
Trip Trip Enable Trip Threshold Trip Delay DIM Parameter Phase Imb Fault V Imbal Trip Lev V Imbal Dly Set Point {On, Off} 1 100% 0.0 60.0 Seconds Step N/A 1% 0.1 Second Default On 6% 0.5 Second
B-6
MN03902002E
Under Voltage The S811 monitors the minimum RMS value of the three phase voltages. The unit will trip with a motor under voltage fault if the under voltage trip is enabled and the minimum RMS value drops below the trip threshold for the trip delay. Note that the S811 will not generate an under voltage trip when the motor is starting. Table B-14: Under Voltage Settings
Trip Trip Enable Trip Threshold Trip Delay DIM Parameter Low Volt Trip Low Volt Level Low Volt Trip Dly Set Point {On, Off} 1 99% Rated 0.0 60.0 Seconds Step N/A 1% 0.1 Second Default On 90% 3.0 Second
Over Voltage The S811 monitors the maximum RMS value of the three phase voltages. The unit will trip with a motor over voltage fault if the over voltage trip is enabled and the maximum RMS value rises above the trip threshold for the trip delay. Table B-15: Over Voltage Settings
Trip Trip Enable Trip Threshold Trip Delay DIM Parameter Hi Volt Trip Hi Volt Level Hi Volt Trp Dly Set Point {On, Off} 101 120 %Rated 0.0 60.0 Seconds Step N/A 1% 0.1 Second Default On 110% 3.0 Second
Mains Faults If a start is commanded and voltage mains are not present or are not in a safe range for the S811 to attempt a start, a fault will be generate according to the following table. Table B-16: Fault Generation
Fault Mains Loss Motor Under Voltage Motor Over Voltage Condition Average RMS of three phase voltages is less than 80 volts Minimum phase RMS voltage is less than 80 volts Maximum phase RMS voltage is greater than 800 volts
MN03902002E
B-7
Enable Threshold Delay Threshold Delay Class 5 10 20 30 Threshold Delay Enable Threshold Delay Enable Threshold Delay Enable
Jam Fault Not User Settable Not User Settable Not User Settable Not User Settable
{On, Off} 3x FLA 1.5 Seconds 4x Catalog FLA 2.0 seconds 4.0 seconds 6.0 seconds 8.0 seconds 1 100% 2.0 seconds {On, Off} 1 100% 0.0 60.0 Seconds {On, Off} 1 100% 0.0 60.0 Seconds {On, Off}
Low I Trip % FLA Not User Settable Phase Imb Fault I Imbal Trip Lev I Imbal Dly Phase Loss Fault Phase Loss % Trp Phase Loss Dly Phase Rev Fault
#6 Phase Loss
Motor energized
#7 Voltage Imbalance
Mains Present; when monitored sequence differs from Incoming Phase Sequence parameter When start is attempted
Phase Imb Fault V Imbal Trip Lev V Imbal Dly Low Volt Trip Low Volt Level Low Volt Trip Dly Hi Volt Trip Hi Volt Level Hi Volt Trp Dly Not User Settable Not User Settable Not User Settable
Motor energized
{On, Off} 1 100% 0.0 60.0 Seconds {On, Off} 1 99% Rated 0.0 60.0 Seconds {On, Off} 101 120 %Rated 0.0 60.0 Seconds 80 volts 80 volts 800 volts
N/A 1% 0.1 Second N/A 1% 0.1 Second N/A 1% 0.1 Second N/A N/A N/A
On 6% 0.5 Second On 90% 3.0 Second On 110% 3.0 Second N/A N/A N/A
B-8
MN03902002E
1.15SF 10 20 30 40 60 75 100
575 690V Catalog 1.0SF 1.15SF Number 30 60 100 125 150 200 300 30 50 75 100 150 200 250 S811N37N3S S811N66N3S S811R10N3S S811R13N3S S811T18N3S S811T18V3S S811T24N3S S811T24V3S S811T30N3S S811T30V3S S811U36N3S S811U42N3S S811U50N3S S811V36N3S S811V36V3S S811V42N3S S811V42V3S S811V50N3S S811V50V3S S811V65N3S S811V65V3S S811V72N3S S811V72V3S S811V85N3S S811V85V3S S811V10N3S
Frame Size U 360 110 420 129 500 150 Frame Size V 360 110 420 500 650 720 850 1000 129 150 200 220 257 277
185 220 257 185 220 257 355 400 475 525
150 175 200 150 175 200 250 300 350 400
125 150 150 125 150 150 200 250 300 350
300 350 400 300 350 400 500 600 700 800
250 300 350 250 300 350 450 500 600 700
350 450 500 350 450 500 600 700 900 900
300 350 450 300 350 450 500 600 700 800
MN03902002E
C-1
Table C-2: 25 Second Ramp, 4 Starts per Hour, 300% Current Limit @ 40C
Three-Phase Motors kW Rating (50 Hz) Max. Current 230V Frame Size N 34 9 63 15 Frame Size R 96 25 120 33 Frame Size T 150 45 215 278 63 80 380 400V 15 30 45 63 80 110 147 440V 18.5 33 55 63 90 132 160 hp Rating (60 Hz) 200V 230V 1.0SF 1.15SF 1.0SF 10 20 30 40 50 60 75 7-1/2 15 25 30 40 60 75 10 20 30 40 50 75 100
1.15SF 10 20 30 40 50 60 75
575 690V Catalog 1.0SF 1.15SF Number 30 60 75 100 150 200 250 25 50 75 100 125 150 250 S811N37N3S S811N66N3S S811R10N3S S811R13N3S S811T18N3S S811T18V3S S811T24N3S S811T24V3S S811T30N3S S811T30V3S S811U36N3S S811U42N3S S811U50N3S S811V36N3S S811V36V3S S811V42N3S S811V42V3S S811V50N3S S811V50V3S S811V65N3S S811V65V3S S811V72N3S S811V72V3S S811V85N3S S811V85V3S S811V10N3S
Frame Size U 320 90 380 110 460 140 Frame Size V 320 90 380 460 610 680 810 890 110 140 185 200 250 290
160 200 250 160 200 250 315 375 450 510
185 220 280 185 220 280 375 445 500 560
125 150 150 125 150 150 200 250 300 400
100 125 150 100 125 150 200 200 300 350
250 300 350 250 300 350 500 600 700 700
200 250 300 200 250 300 450 500 600 600
300 350 450 300 350 450 600 700 900 900
250 300 400 250 300 400 500 600 700 700
C-2
MN03902002E
Table C-3: 15 Second Ramp, 4 Starts per Hour, 300% Current Limit @ 50C
Three-Phase Motors kW Rating (50 Hz) Max. Current 230V Frame Size N 34 9 63 15 Frame Size R 96 25 120 33 Frame Size T 150 45 215 278 63 80 380 400V 15 30 45 63 80 110 147 440V 18.5 33 55 63 90 132 160 hp Rating (60 Hz) 200V 230V 1.0SF 1.15SF 1.0SF 10 20 30 40 50 60 75 7-1/2 15 25 30 40 60 75 10 20 30 40 50 75 100
1.15SF 10 20 30 40 50 60 75
575 690V Catalog 1.0SF 1.15SF Number 30 60 75 100 150 200 250 25 50 75 100 125 150 250 S811N37N3S S811N66N3S S811R10N3S S811R13N3S S811T18N3S S811T18V3S S811T24N3S S811T24V3S S811T30N3S S811T30V3S S811U36N3S S811U42N3S S811U50N3S S811V36N3S S811V36V3S S811V42N3S S811V42V3S S811V50N3S S811V50V3S S811V65N3S S811V65V3S S811V72N3S S811V72V3S S811V85N3S S811V85V3S S811V10N3S
Frame Size U 320 90 380 110 460 140 Frame Size V 320 90 380 460 610 680 830 960 110 140 185 200 257 302
160 200 250 160 200 250 315 375 450 510
185 220 280 185 220 280 375 445 500 540
125 150 150 125 150 150 200 250 300 350
100 125 150 100 125 150 200 200 300 300
250 300 350 250 300 350 500 600 700 800
200 250 300 200 250 300 450 500 600 700
300 350 450 300 350 450 600 700 900 900
250 300 400 250 300 400 500 600 700 800
MN03902002E
C-3
Table C-4: 50 Second Ramp, 2 Starts per Hour, 300% Current Limit @ 50C
Three-Phase Motors kW Rating (50 Hz) Max. Current 230V Frame Size N 21 5.5 42 11 Frame Size R 60 15 80 22 Frame Size T 115 33 150 192 45 55 380 400V 10 18.5 30 40 59 80 100 440V 11 22 33 45 63 90 110 hp Rating (60 Hz) 200V 230V 1.0SF 1.15SF 1.0SF 5 10 15 25 30 50 60 5 10 15 20 30 40 50 5 15 20 30 40 50 60
1.15SF 5 10 15 25 30 50 60
575 690V Catalog 1.0SF 1.15SF Number 15 40 50 75 100 150 200 15 30 50 60 100 125 150 S811N37N3S S811N66N3S S811R10N3S S811R13N3S S811T18N3S S811T18V3S S811T24N3S S811T24V3S S811T30N3S S811T30V3S S811U36N3S S811U42N3S S811U50N3S S811V36N3S S811V36V3S S811V42N3S S811V42V3S S811V50N3S S811V50V3S S811V65N3S S811V65V3S S811V72N3S S811V72V3S S811V85N3S S811V85V3S S811V10N3S
Frame Size U 280 80 340 110 380 110 Frame Size V 280 80 340 380 420 480 590 650 110 110 129 147 180 205
150 180 200 150 180 200 220 257 315 370
160 200 220 160 200 220 257 295 375 415
100 125 150 100 125 150 150 200 200 250
200 250 300 200 250 300 350 400 500 500
200 200 250 200 200 250 300 350 400 450
250 350 350 250 350 350 450 500 600 600
250 300 300 250 300 300 350 450 500 500
C-4
MN03902002E
Table C-5: 15 Second Ramp, 4 Starts per Hour, 450% Current Limit @ 40C
Three-Phase Motors kW Rating (50 Hz) Max. Current 230V Frame Size N 29 7.5 49 12.5 Frame Size R 73 18.5 94 25 Frame Size T 155 45 219 280 63 80 380 400V 12.5 22 37 45 80 110 150 440V 15 25 40 55 90 132 160 hp Rating (60 Hz) 200V 230V 1.0SF 1.15SF 1.0SF 7-1/2 15 20 30 50 60 75 7-1/2 10 20 25 40 60 75 10 15 25 30 60 75 100
1.15SF 7-1/2 15 20 30 50 60 75
575 690V Catalog 1.0SF 1.15SF Number 25 40 60 75 150 200 250 20 40 60 75 125 150 250 S811N37N3S S811N66N3S S811R10N3S S811R13N3S S811T18N3S S811T18V3S S811T24N3S S811T24V3S S811T30N3S S811T30V3S S811U36N3S S811U42N3S S811V36N3S S811V36V3S S811V42N3S S811V42V3S S811V50N3S S811V50V3S S811V65N3S S811V65V3S S811V72N3S S811V72V3S S811V85N3S S811V85V3S S811V10N3S
Frame Size U 345 100 405 110 Frame Size V 345 100 405 465 530 590 651 754 110 140 160 180 200 220
MN03902002E
C-5
Table C-6: 30 Second Ramp, 4 Starts per Hour, 450% Current Limit @ 40C
Three-Phase Motors kW Rating (50 Hz) Max. Current 230V Frame Size N 21 5.5 40 11 Frame Size R 55 15 75 22 Frame Size T 151 45 215 264 63 80 380 400V 10 18.5 25 37 80 110 140 440V 12.5 22 30 45 90 132 160 hp Rating (60 Hz) 200V 230V 1.0SF 1.15SF 1.0SF 5 10 15 20 50 60 75 5 10 15 20 40 60 75 5 10 20 25 50 75 100
1.15SF 5 10 15 20 50 60 75
575 690V Catalog 1.0SF 1.15SF Number 15 30 50 60 150 200 250 15 30 40 60 125 150 200 S811N37N3S S811N66N3S S811R10N3S S811R13N3S S811T18N3S S811T18V3S S811T24N3S S811T24V3S S811T30N3S S811T30V3S S811U36N3S S811U42N3S S811V36N3S S811V36V3S S811V42N3S S811V42V3S S811V50N3S S811V50V3S S811V65N3S S811V65V3S S811V72N3S S811V72V3S S811V85N3S S811V85V3S S811V10N3S
Frame Size U 300 90 340 100 Frame Size V 300 90 340 380 420 460 500 560 100 110 129 140 150 160
C-6
MN03902002E
Severe Duty Ratings Table C-7: > 30 Second Ramp, > 4 Starts per Hour or >300% Current Limit
Three-Phase Motors kW Rating (50 Hz) Max. Current 230V Frame Size N 22 5.5 42 11 Frame Size R 65 15 80 22 Frame Size T 115 33 150 192 45 55 380 400V 10 18.5 30 40 59 80 100 440V 11 22 33 45 63 90 110 hp Rating (60 Hz) 200V 230V 1.0SF 1.15SF 1.0SF 5 10 15 25 30 50 60 5 10 15 20 30 40 50 7-1/2 15 20 30 40 50 75
1.15SF 5 10 15 25 30 50 60
575 690V Catalog 1.15SF 1.0SF 1.15SF Number 10 25 40 50 75 100 125 20 40 50 75 100 150 200 15 30 50 60 100 125 150 S811N37N3S S811N66N3S S811R10N3S S811R13N3S S811T18N3S S811T18V3S S811T24N3S S811T24V3S S811T30N3S S811T30V3S S811U36N3S S811U42N3S S811V36N3S S811V36V3S S811V42N3S S811V42V3S S811V50N3S S811V50V3S S811V65N3S S811V65V3S S811V72N3S S811V72V3S S811V85N3S S811V85V3S S811V10N3S
Frame Size U 240 75 305 90 Frame Size V 240 75 305 365 420 480 525 575 90 110 129 147 160 172
Severe Duty Ratings are dened as any combination of parameters that exceed the Standard Duty Ratings where the ramp time is over 30 seconds, the number of starts per hour exceeds 4, or the current limit set is over 300%. Example: 35-Second Ramp, 5 Starts per Hour, 350% Current Limit @ 40C Ambient.
MN03902002E
C-7
Cooling
Microcontroller controlled fans are used to cool the IT. Soft Starter. The fans are turned on when the temperature of any of the thermal sensors exceeds preset value. Once the fans are started, they will not go off until the temperature goes below the off set point for 10 minutes. The fans will also be turned on whenever the IT. is started, stopped or jogged. The fans will remain on for 10 minutes to assure the SCRs are adequately cooled prior to the next start. If a temperature is sensed above a second preset level, a Pole Over-Temperature Fault will occur. This fault cannot be reset until the temperature returns to a safe level. Note: The fans will only operate if 24V DC is applied to the + and terminals. Cycling power during the 10 minute timeout after a start, stop or jog will reset the fans to off.
C-8
MN03902002E
Power Losses
The following table lists the maximum power loss for each IT. Soft Starter when it is operating in the across-the-line mode with its bypass contactor pulled in. These losses should be used in conjunction with the losses of another cabinet mounted device to determine the enclosure size and any cooling requirements. Table C-8: Maximum Power Loss
Frame Size N R T Catalog Number S811N37N3S S811N66N3S S811R10N3S S811R13N3S S811T18N3S S811T18V3S S811T24N3S S811T24V3S S811T30N3S S811T30V3S U S811U36N3S S811U42N3S S811U50N3S V S811V36N3S S811V36V3S S811V42N3S S811V42V3S S811V50N3S S811V50V3S S811V65N3S S811V65V3S S811V72N3S S811V72V3S S811V85N3S S811V85V3S S811V10N3S 310 1000 215 265 850 164 225 720 127 203 650 109 156 500 78 131 420 64 112 360 131 420 156 500 112 360 76 92 116 56 95 304 45 75 240 40 Current Range 11 37 20 66 32 105 42 135 56 180 Across-the-LineLosses (Watts) 30 33 47 55 37
MN03902002E
C-9
C-10
MN03902002E
The EMS38 is panel mounted, while the EMS39 and EMS41 are mounted directly on the IT. Soft Starter. In situations where an MOV must be used, the installer may choose to apply a different transient absorption device, but it must be equivalent to the EMS38, EMS39 or EMS41. These MOVs may also be used on the load side of the soft starter where long cables connect the motor to the soft starter or where the cables are located outdoors.
MN03902002E
D-1
Wye-Delta Motor
The wye-delta motor is a traditional way of achieving a reduced voltage start using regular contactors and starters. In this method, the motor is constructed with all six leads brought out to connect the unit in a wye conguration. This allows about 58% of the current (33% starting torque) to be applied during start-up. A timer is used to control the circuit and switch to the delta conguration as the unit approaches full speed. In this case, wire the six-lead motor in a standard delta conguration. The soft starter is then used to control the voltage and motor torque without the need for additional circuitry. An insight disconnect means should be installed, per local code. The IT. Soft Starter must be wired into the three-phase line feeding the three main motor input leads as would be done for normal across-the-line starting. It must not be wired internally between motor windings in an inside-the-delta conguration. If an inside-the-delta starting conguration is desired, please contact Eaton for details about our inside-the-delta soft starters, designated S811**D.
Multi-Speed Motor
Some motors have multiple windings to allow operation at different base speeds. The multiple speeds are sometimes utilized for soft starting and other times for a process requirement of the machine to which it is attached. If only one speed is required, the motor should be wired for that speed. If multiple speeds are required, the appropriate contactors will need to be connected to the output of the Soft Starter. The contactors must be in the selected speed position before the soft starter is started. The motor must be stopped and the soft starter turned off before the speed selection contactors are changed.
D-2
MN03902002E
Caution
Attention
Precaucin
Never megger a motor while it is connected to the IT. Soft Starter. Disconnect the leads at the IT. Soft Starter before meggering the motor.
Ne jamais rgler un moteur alors quil est branch au dmarreur progressif IT. Dbrancher les ls au dmarreur progressif IT. Avant de rgler le moteur.
Nunca efecte pruebas del motor con un meghmetro mientras est conectado al arrancador Soft Starter IT. Desconecte los cables en el arrancador IT. antes de usar el meghmetro.
MN03902002E
D-3
D-4
MN03902002E
Status Bar
Soft Keys
Predened Keys
MN03902002E
E-1
Adjustment All of the adjustments to the IT. Soft Starter are made as noted in this user manual. The major difference between the standard IT. Soft Starter and one with the pump start option is the special algorithm for gentle start and stop with centrifugal ow loads to minimize the potential for water hammer. Using the DIM, set the S811 Soft Start Conguration parameters described below: The Start Ramp Time parameter adjusts the start ramp. It has a standard range of 0.5 to 180.0 seconds. The factory default is 20.0 seconds. The soft stop time is adjusted by Pump Stop, which has a range of 30.0 to 120.0 seconds with the factory default being 120 seconds. (NOTE: The Stop Ramp Time setting used in non-pump S811s has no effect on units with the Pump Control Option installed if start method is Pump Start.) These adjustments are application dependent, and should be made to minimize any surge or water hammer effects. Typically Pump Stop would not be set short, since the stop might not differ much from a coast-to-stop. The soft stop time adjustment may often be in the range of 30 to 40 seconds, but needs to be set appropriately for the system requirements. If reduction or elimination of water hammer is not achieved, it may be necessary to lengthen Pump Stop to achieve the desired result. Note that long stop times will result in greater motor heating than shorter stop times. This can affect the number of start/stop cycles allowed per hour due to the IT. Soft Starter or motor thermal limits.
E-2
MN03902002E
Status Bar
Soft Keys
Predened Keys
Figure F-1: DIM (Digital Interface Module) The DIM allows a user three basic modes: Display Mode where the status of the system can be viewed (this is the default view on powerup). Parameter Edit Mode where Menus are displayed, and a user can view and change Items. The ESCape key is used to switch between the two different modes. Fault Mode this mode overlays the Display Mode when a fault is active. It will not supersede active Parameter Edit.
MN03902002E
F-1
Modes of Operation
Display Mode In this mode, the User Interface shows four things:
The device that the UI is connected to (the S811) The Hand or Auto system status (H or A in the upper right) The status of the S811 (Running, Faulted, Stopped, At Ref) The 3-Phase Pole Line Current for the S811
Figure F-2: Display Mode LCD Parameter Edit Mode In this mode, the user can navigate through the S811 Menus and Items, and potentially edit parameters if they are Read-Write. Also, multi-element Items are supported, as well as enumerated Items (items that are represented by a symbolic or textual description).
Figure F-3: Parameter Edit Mode LCD Fault Mode If the DIM is on the Display screen, and a fault occurs, the Display screen is replaced with a fault overlay, displaying what the fault is. This screen will go away and go back to the Display screen if the fault clears itself, or if the user presses the ESCape key.
F-2
MN03902002E
Button Operation
Soft Keys The DIM has three Soft Keys that change their operation based on context. These keys typically represent Increase/Decrease/Enter, but change based on the menu that the DIM is in. The function that they represent is displayed at the bottom of the LCD Screen.
Figure F-5: Soft Key Functions Above Soft Keys On the User Display screen the DIM has the Soft Keys dened as follows: JOG The Jog applies a momentary Run command as the button is held down. The soft start will start ramping the frequency up to line frequency until the button is released, at which time the unit will stop, using the Load Release mode of stopping. The bypass contact does not close even when up to speed. If the unit is able to jog, the upper right Motor Control Status notication will say RUN2 during a jog. RESET This resets the active system fault, if the fault is not being presently asserted. The fault can be found in the Motor Control Menu and is called App Status. When the unit is not actively faulted, this will be 0. Note that Motor Control Menu/Fault Warning Queue contains the most recent 10 faults in temporal order. The DIM will reect a faulted condition requiring a Reset fault in the upper right status box, which will ash Faulted. A->H or H->A This soft key switches the command from the DIM from AUTO to HAND (A->H), or from HAND to AUTO (H->A). If an On (1) or Off (0) command has been pushed on the DIM, the DIM is subsequently in HAND mode and can be switched back to AUTO using the H->A button. Hand operation works as follows:
If any device is commanding HAND, the S811 system is in HAND (and this is reected as H in the upper right). If the system is in HAND, only devices that are in HAND can issue a Run command. The UI will go into HAND if a Run or Stop command is pressed.
See Appendix A for a Ladder Logic representation of HAND and AUTO system operation. Other Common Soft Keys (used when editing parameters) are: INC and DEC Increment or Decrement the value of the parameter actively being edited. NEXT and PREV Next and Previous go through the Menus or through the Items in the forward or reverse direction. MORE If the present parameter has multiple elements, the MORE key will be displayed. It will allow the element of the parameter to be selected.
MN03902002E
F-3
EDIT Edit the parameter being shown. Note that if a parameter is Read Only this will not be displayed. Also, if the Access Level (password) entered is not high enough to be able to change the parameter, the EDIT button will not be displayed. SAVE Save the value being edited at the value that is currently being displayed. ENTER Used to Enter into a Menu to View Items. The following are lesser-used Soft Keys (used when editing parameters). SELECT Used when setting Access Level, and when doing Get Reg and Set Reg operations. MENU Used to get to DIM menus if an internal fault occurs. SCAN Used in the LCD DIM Setup menu to Scan for Devices. GROUP and MEMBER Used in the LCD DIM Setup menu to select the upper and lower byte of the ID to send an explicit command to. SEND Used in the LCD DIM Setup menu to send an explicit command. Predened Keys
ESC
Figure F-6: Predened Keys Escape Key The Escape key brings the DIM out of the operation that it currently is in. At the top level, it switches the DIM between the User Display screen and the Parameter Edit screen. 1 and 0 (Start and Stop) Keys The On (1) key sends a start command to the device that the DIM is currently connected to (the S811). The Off (0) key sends a stop command to that device. If the S811 responds to the On command, the Motor Control status notication in the upper right will reect this by going from STOP to RUN1. Note: TO AVOID INADVERTENT STARTING OF THE S811, THE ON (1) BUTTON MUST BE HELD FOR MORE THAN 0.3 SECONDS TO INITIATE A START. This amount of time is adjustable in the LCD DIM Setup menu, and is called Run Delay. It can be adjusted down to 0.1 seconds. If Run Delay is set to 0, the RUN button is disabled for the DIM.
F-4
MN03902002E
Figure F-7: Status Bar on LCD Device Connection Status Text This area is visible from the User Display screen. It represents the device that is actively being controlled (and typically will display S811).
Figure F-8: Device Connection (User Display Only) Connection Status This represents whether the DIM is connected on the wire to other devices. This is viewable while navigating menus but not in User Display mode.
MN03902002E
F-5
OFLN Ofine most likely the only device on the wire, with no other active device to talk to. ONLN Online actively talking to another device. The normal mode of operation to be in. FLT Faulted mode an internal communications fault has occurred. UNDS Undiscovered the DIM has not yet entered into active communications with other devices. Most likely after a factory reset of the DIM (or if the DIM is in an out-of-the-box condition). Attaching to the S811 and cycling power to the system will correct this. On powerup the S811 will send commands to the DIM to recongure its communication, and the S811 will send a reset to the DIM after conguration is done (this process takes approximately 20 seconds). Mode of Operation Represents the communication protocol the DIM is congured to communicate using. This is viewable while navigating menus but not in User Display mode.
Figure F-10: Mode of Operation UN Uncongured mode the DIM has not yet been connected to an S811 that has congured it. SS Simple System this is the typical conguration to be in when connected to the S811. MS Master Slave this mode is not typically used for user interfaces. Master Slave is a mode used between the S811 and a Gateway. WR Wire Replacer used for Digital Input/Output models. ER Error mode an internal error has occurred.
F-6
MN03902002E
Connection Destination This represents the Device ID that the DIM is connected to. Typically it will always reect the Soft Start ID (0xFD01). This is viewable while navigating menus but not in User Display mode.
Figure F-11: Connection Destination HAND/AUTO Status This represents whether the system is in Hand (H) or Auto (A). If any device on the wire is asserting HAND, this status will reect the S811 System Status of HAND.
Figure F-12: HAND/AUTO Status Motor Control Status This represents the status of the S811 device (whether it is conducting current, stopped, faulted, etc.). It is visible on both the User Display and Edit modes. RUN1 S811 is in Run mode. RUN2 S811 is being actively Jogged. STOP S811 is not in Run mode, not being Jogged and not faulted. FLT S811 is faulted. WARN S811 has an active warning. REF S811 is At Reference (up to speed with bypass closed).
MN03902002E
F-7
Parameter Navigation/Editing
The ESCape key will take the DIM from the User Display screen to the Parameter Edit screens (as well as back to the User Display screen). Menu Selection The rst screen allows the user to select the menu to edit. Note that the bar at the bottom will indicate the menu position in the list of all menus. A Soft Key under NEXT indexes through the menus forward, and a Soft Key under PREV (Previous) moves the DIM backwards through the menus.
Figure F-14: Bar Indicates Menu Position Pressing the Soft Key under ENTER will allow the user to select the item to view and possibly Edit. Note that the bar on the side will indicate the item position in the list of all Items. Item Selection Once a menu has been selected, the items within that menu can be scrolled through using the Soft Keys under NEXT and PREV. NEXT will index forward through the menu (causing the item bar to become larger), and PREV will cause it to index backward (causing the item bar to become smaller).
F-8
MN03902002E
Read Write Operation If a parameter is editable, the Soft Key under EDIT will be available on the lower right. Pressing EDIT will highlight an edit value that changes with INC and DEC, and also shows a bar that represents the edited value scaled between the min and max of that parameter.
MN03902002E
F-9
Parameters with Multiple Elements Navigation and Editing Some parameters have multiple elements. MORE will highlight the Element number, and NEXT and PREV will allow selection of which Element to view. In Figure F-17, the numerical value of Element 0 of the Fault Queue is the number 4.
Figure F-17: Use MORE to Highlight Element Enumerated Values Some values have an alphanumerical text description as well as a numerical value. These values will be shown in addition to the internal numerical representation. For instance, Fault/ Warning Queue Element 0 is a 4, which symbolically represents Control Voltage Low.
F-10
MN03902002E
Level 3
Note: The number of items in the LCD DIM Setup menu (parameters that are local to the DIM) will increase with higher Access Levels (more parameters on the local DIM menu will be visible). This is to expand complexity and the number of parameters for experienced users. Set Access Level A user can increase the Access Level of the DIM provided he has the password for that level. The default Password for levels 1 and 2 is 0, which does not need to be typed in to enter that level. A user can then assign a password with Change Password. All three levels have a hardcoded back door password. Contact Eaton Product Support for additional help.
MN03902002E
F-11
Change Password for an Access Level Once a user is at a specied access level, the password for that level and levels below it can be changed. This change will be saved to Eeprom.
Figure F-19: Changing Passwords Access Level Timeout is a numerical value that can be set to cause the DIM to go back to Level 0 after a specied period of inactivity. It can be set for between 60 seconds and 600 seconds, after which if no keys have been pressed the DIM will revert to Level 0. To disable this function, set the value to Max (600). If enabled, the DIM will always power up at Level 0.
Fault Display
If the DIM is on the User Display screen and a fault occurs on the S811, the DIM will reect the fault with a bold overlay describing the fault textually. If the user is navigating menus, the fault overlay will not occur. In all instances, the upper right status area will display FLT. If the fault is cleared by some other remote device, or cleared by a terminal block Fault Clear, the fault overlay will go away by itself, and the DIM will go back to the User Display screen. A user can press the ESCape key, which will also put the DIM back to the User Display screen. The Fault is represented internally with the Faulted bit in the Motor Control Status byte.
Figure F-20: Fault Display See Page 8-6 for a full listing of fault codes and corrective actions.
F-12
MN03902002E
The S811 commands the DIM to produce Motor Control command at the DIMs Production Interval. The S811 commands the DIM to consume Motor Control status at greater than the Consumption Interval. The DIM saves its Device ID and gets congured to the Simple System mode.
Multiple devices can be attached to the IT. Soft Starter (more than one DIM, a handle mechanism, etc.). If additional devices are added to a running system, the system may need to be re-congured to accommodate these devices. A reconguration of all devices can be initiated using the following procedure from the DIM. See Table F-2. Table F-2: Reconguring All Devices
Step 1 Procedure Go to the LCD DIM Setup menu.
Select MORE and press the SEND button. This broadcasts the Factory Reset to Device ID 0x0000, which causes all devices to reset.
The DIM and all other connected nodes on the Local port will begin an internal reconguration and within 10 seconds will reset.
A Reset Factory Defaults command will recongure the DIM to default values and will set the Level 1 and Level 2 passwords back to 0. It will not change the Serial Number and will not change the programmed Level 3 password.
MN03902002E
F-13
F-14
MN03902002E
MN03902002E
F-15
Level 0 Access Level See Page F-11 Access Level is a number between 0 and 3. The access level represents the restrictions on being able to edit and view settings (AKA password). Zero (0) is most restrictive and 3 is least restrictive. The Level 1 Default Password is 42 and the Level 2 Default Password is 4201. Password This allows a user to set the numerical password for the Access Level that they are on, as well as Access Levels below that. Using this parameter does not change the Default Password. Backlight Level The UI has a backlight that can be set to a value 0 3, 0 being Off and 3 being full On. If the LCD DIM Setup parameter Inactivity Timeout is set to non-0, a timeout will turn the display backlight off after this many seconds of non-activity (not pushing the switches for this many seconds). Backlight Time This value represents the number of seconds of inactivity before the backlight LEDs turn off. If set to 0, the backlight will remain on all the time. Screen Contrast This value adjusts the relative contrast of the LCD in the DIM. The default value should be good for most applications, and the DIM will adjust the contrast based on a high temperature. If the contrast has been adjusted to the point where the screen is no longer readable, simultaneously pressing the upper left, upper right, escape and stop keys will set the contrast back to the factory default setting. Identify Node send an identify command to a QCPort device. Clear Fault Queue This sends out a clear command over the wire to the Destination device(s) specied. Firmware Version This represents the rmware revision in Major-Minor format. App Status This represents the current Active Fault in the UI. Note that this may be a different value than the App Status found in the Motor Control menu (which represents the active fault in the S811). Device Temp Deg C This is the internal temperature of the LCD DIM in x.x Degrees C. This read-only parameter is used to auto-adjust the contrast at high temperature. Node ID The LCD DIM QCPort address, used for communications. Device ID Tag This is a string that describes the product. Language List A list of available languages for Text. Language Select Language the DIM is presently set to. Level 1 (variables editable IN ADDITION to the ones in Level 0) Term Resistors This parameter turns on and off the termination resistors. In an RS-485 system only one device typically has termination resistors turned on. If a number of devices are on the IT. Soft Starter Local bus, consult factory regarding this parameter.
F-16
MN03902002E
Level 2 (variables editable IN ADDITION to the ones in Levels 0 and 1) Scan For Devices show a scan list of devices to communicate with. Start Discovery Send out a Discovery command to look for other devices. Reset-Soft Send a software reset to all devices selected within the address range specied. Reset-App Cfg This sends an Application Conguration Reset command to all devices selected within the address range specied. Reset-App Fault This sends an Application Fault Reset command to all devices selected within the address range specied. Reset-Commission This sends a Remote Commission Reset command to all devices selected within the address range specied. Get Register This is a mechanism to allow read access to internal product settings and parameters. Contact Factory Technical support for details. Inactive Timeout If this value is set to non-zero the UI will revert from the programming Menus back to the User Display menu after the set period of key inactivity. If this is set to 0, the feature is disabled. Fault Disp Time If this value is set to non-zero, the DIM will revert from the Fault Overlay popup back to the User Display menu after the set period of key inactivity. If this is set to non0, the feature is disabled. Motor Control The bit command that the DIM is generating (the command that it sends to the S811). Bit 0 Run1 Bit 1 Run2 Bit 2 Permissive Bit 3 Fault Reset Bit 4 Local Control Bit 5 Local Control Capable Device Motor Control Status Bit 0 Running 1 Bit 1 Running 2 Bit 2 Permissive Bit 3 Reserved Bit 4 Local Control Bit 5 Faulted Bit 6 Warning Bit 7 At Reference
MN03902002E
F-17
Device Identity This array parameter consists of the following segments Byte 0-1 Product Code Byte 2-3 Vendor ID Byte 4-7 Serial Number Byte 8-9 Hardware Version Bytes 10-11 Firmware Version Bytes 12-13 Protocol Version Cong CRC A CRC check can be used to verify that the device at this node has a specic conguration and/or to guarantee that a node is being replaced with one that has similar characteristics. Production Dest This represents the Node that the DIM produces its Motor Control, and expects to receive its Motor Control Status from. Note: For the commands above that allow commands to be sent to remote devices, the Default Device specied is 0x0000, which is a broadcast to clear the Fault Queue in all devices. The GROUP button increases the Group Address ID and the Member increases the member Address ID. The SEND button sends out the command. Level 3 (variables editable IN ADDITION to the ones in Levels 0, 1 and 2) Access Timeout If the DIM pushbuttons are not actively manipulated for greater than this number of seconds, the DIM will revert back to level 0. Range 60 600 Seconds. Setting the parameter to 600 Seconds (max) disables the feature and lets the DIM stay at the current Level indenitely. Reset-Factory This sends a Set Factory Defaults command to all devices selected within the address range specied. Set Register This is a mechanism to allow write access to internal product settings and parameters. Contact Factory Technical support for details. Run Delay This parameter species the duration that the START pushbutton has to be held down before the Start is recognized as valid (in tenths of a second). Setting this value to 0 will disable starts from the DIM. Transient Source If this value is set to 1 (enabled) the UI will be able to disconnect from a Controlling Node without causing a communications loss fault. Refresh Rate This parameter species the rate at which the data displayed on screen is refreshed from the remote source. Device Mode This reects the mode that the DIM is using for communication (typically set to Simple System after the S811 initializes it). The DIM comes out of the box as Uncongured. Baud Rate Set the rate at which QCPort communicates. Typically set to 57.6kBaud. Production Intvl This sets the rate at which DIM produces its data. Consumption Intvl This represents how long the DIM will wait after the last production from the S811 before issuing a communications loss fault.
F-18
MN03902002E
Low cost implementation Wire reduction Out-of-box functionality for simple systems PLC5-Class scanning performance for polled I/O applications
Complete QCPort application information is not covered in this manual. Contact your local Eaton representative or see QCPort System Installation Manual MN0500010002E for more information. S811 Communications Ports The S811 communicates using the QCPort protocol over RS-485. The S811 has three (3) communications ports supporting two separate QCPort networks. The rst port is identied as Channel 0 Remote and the remaining two ports as Channel 1 Local. All three ports use six conductor RJ11 (RJ12) type plugs. QCPort Remote Network CH0 The S811 remote network connection is isolated and designed to be connected to a gateway network. The S811 remote port requires 24V to be supplied via network wiring. The Node ID switch on the front of the S811 is used to set the node ID for this port. QCPort Local Network CH1 (2 places) The local network is designed to be connected to the DIM and other similar local devices. The S811 local communications port supplies 24V to the local network wiring. There is no node ID switch for the local port. The source of the local network power is the S811s main terminal block. The S811 has the local network termination resistors built-in and they are active by default.
MN03902002E
G-1
One remote (CH0) and one local (CH1) network port connection is located on the S811s front cover near the eld connector. The second local (CH1) port connection is located in the front cover pocket and is used to connect the DIM to the S811. Set the remote network (CH0) group ID using the six switches labeled 32 1 located on the front cover of the S811. When using the remote network you must make sure the remote network wiring supplies 24V to the S811s remote port.
Chan 1 Local
To DIM +24V Supplied to DIM +24V Supplied from Local Network To Gateway
Chan 1 Local PIN 1 PIN 2 PIN 3 PIN 4 PIN 5 PIN 6 (+24V) (GND) (B) (A) (+24V) (GND)
Chan 0 Remote PIN 1 PIN 2 PIN 3 PIN 4 PIN 5 PIN 6 (+24V) (GND) (B) (A) (+24V) (GND)
G-2
MN03902002E
Networks
Gateway Local Display Network
24V
M/S QCP (Remote) SS QCP (Local) 7 Esc 7 Motor Control Byte 6 5 4 3 2 1 0 Ch1 Ch0 Motor Control Byte 6 5 4 3 2 1 0
- LCD L Rst P R2 R1
- LCD L Rst P R2 R1
LCD - Local Capable Device L - Local Rst - Fault Reset P - Permissive R2 - Jog R1 - Run
S811 Motor Control Status Motor Control Active List 0 - Running 1 - Main TB - Local Display 1 - Running 2 - Gateway 2 - Permissive 3 - Reserved 4 - Device under Local Control 5 - Fault 6 - Warning 7 - At Reference Device Main Terminal Block COM +24V P 1 2 3 4 7 x x o x x o o o x Hand x Local o Off o Auto
- LCD L Rst P R2 R1
Fault Reset
MN03902002E
G-3
24V
M/S QCP (Remote) SS QCP (Local) 7 Esc 7 Motor Control Byte 6 5 4 3 2 1 0 Ch1 Ch0 Motor Control Byte 6 5 4 3 2 1 0
- LCD L Rst P R2 R1
- LCD L Rst P R2 R1
LCD - Local Capable Device L - Local Rst - Fault Reset P - Permissive R2 - Jog R1 - Run
S811 Motor Control Status Motor Control Active List 0 - Running 1 - Main TB - Local Display 1 - Running 2 - Gateway 2 - Permissive 3 - Reserved 4 - Device under Local Control 5 - Fault 6 - Warning 7 - At Reference Device Main Terminal Block COM +24V P 1 2 3 4 7 Stop Motor Control Byte 6 5 4 3 2 1 0
- LCD L Rst P R2 R1
Start
Jog
G-4
MN03902002E
S811 responds to Motor Control commands from the network controller Selected when all Local devices have relinquished control (all L bit in their respective Motor Control bytes are 0) Note that: All Local devices Permissives must be set or S811 will stop. Local Fault Resets can be performed.
Removes the ability of network controller to Start or Stop the S811. Motor control can only be performed by Local devices (Port 0 devices and Terminal Block). Note that: Network controller can still monitor S811.
MN03902002E
G-5
Network Run1
S811 Motor Control Byte 0 Field Wire Run1 DIM Run1 Run1
2 Network Permissive Field Wire Permissive DIM Permissive Network Reset Field Wire Reset DIM Reset 4 Field Wire Local DIM Local Local Control Request (Hand) 5 Terminal Block Always Present 1 Local Control Device 6 0 Transient Device 3 Fault Reset Permissive
Note: Although it is possible for a network device to assert itself as a local (HAND) device, this mode of operation is NOT APPROVED and should not be attempted. AUTO devices should not be able to override the OFF state asserted in HAND.
7 0 Reserved
G-6
MN03902002E
Data Parameters
0x0001 (1) Production Data
Size: Description:
Varies This list contains the concatenated values of QCPort Parameters specified in QCPort Configuration Parameter 0x800C, Production List. Varies This list contains the concatenated values of QCPort Parameters specified in QCPort Configuration Parameter 0x800D, Consumption List. 1 byte This parameter indicates the QCPort fault condition that caused a device to enter the Fault Mode, as enumerated below: 0x00 No QCPort Fault. 0x01 Node ID Conflict 0x02 Invalid Node ID in Master/Slave 0x03 Physical Node ID does not match actual ID 0x04 Duplicate configured nodes online. 0x05 Dynamic Node ID overflow 0x06 Invalid baud rate selected 0x07 Errant Device fault 0x08 Problem with data in non-volatile memory 2 bytes This parameter indicates the application status of the QCPort device. It reports the most recent fault or warning code. If there have been no faults or warnings, it reports 0. Reset clears this parameter. 1 byte One byte comprised of 8 bits assigned as follows: 0 Run1 1 Run2 / Jog 2 Permissive 3 Fault Reset 4 Local Control Request (Not used in Master Slave mode) 5 Local Control Device 6 Transient Device 7 Reserved
0x0002
Size: Description:
0x0003
Size: Description:
0x0004
Size: Description:
0x000B
Size: Description:
MN03902002E
H-1
0x000C
Size: Description:
1 byte One byte comprised of 8 bits assigned as follows: 0 Running1 1 Running2 2 Permissive Active 3 Reserved 4 Device Under Local control 5 Faulted 6 Warning 7 At reference 2 bytes Refer to Appendix B for a description of the Motor Protection Faults listed below. Two bytes comprised of 16 bits assigned as follows: Bit 0 Phase Loss 1 Phase Imbalance 2 Thermal Overload 3 Overcurrent 4 Breaker Trip 5 Ground Fault 6 Stall 7 Jam 8 Device Over Temperature 9 Underload 10 Reserved 11 E-Stop 12 Reserved 13 Reserved 14 Reserved 15 Other Fault - See Fault Code Table, Page 8-6. 2 bytes Unsigned integer representing the average of the three RMS line currents in % FLA 4 bytes IEEE floating-point number representing the average of the three RMS line currents in amps. 2 bytes Unsigned integer representing voltage in millivolts.
0x000D
Size: Description:
0x000E
Size: Description:
0x0012
Size: Description:
0x0016
Size: Description:
H-2
MN03902002E
0x0017
Size: Description:
1 byte Unsigned integer representing thermal memory in percent. When the thermal memory value reaches 100% an Overload Fault will occur, if enabled. Other terms for this parameter include thermal capacity and thermal pile. The value in the Thermal Memory parameter is an estimate of motor heating based on the magnitude and duration of current flowing through the motor. 2 bytes Signed integer representing internal device temperature in tenths of a degree Centigrade. 20 bytes Faults are assigned numbers in the range 1 39,999. Warnings are assigned numbers 40,000 65,535. The Fault Queue is a chronological listing of the 10 most recent faults and warnings. The most recent fault goes into Entry 0, shifting the current entries into the next highest entry. If the new fault was already in the queue, the oldest entry is deleted, the current entries are shifted to replace the deleted entry, and the new fault is placed into Entry 0. Duplicate fault codes will not occur in the queue. See Fault Code Table, Page 8-6. 12 bytes Three 4-byte IEEE floating-point numbers representing the three RMS line currents in amps. 12 bytes Three 4-byte IEEE floating-point numbers representing the three RMS pole currents in amps. NOTE: That for inside-the-delta applications the Line and Pole currents will differ by a factor of approximately 3 6 bytes Three 2 byte unsigned integers representing the three incoming line-to-line voltages: VL1-L2, VL2-L3, and VL3-L1 4 bytes Unsigned double integer representing total starts since the unit was shipped from the factory.
0x0018
Size: Description:
0x001A (26) Fault Queue
Size: Description:
0x001B
Size: Description:
0x001C
Size: Description:
0x001D
Size: Description:
0x001F
Size: Description:
MN03902002E
H-3
0x0023
Not supported in all versions of the S811 Soft Starter Size: 2 bytes Description: Two bytes comprised of 16 bits assigned as follows: Bit 0 Phase Loss 1 Phase Imbalance 2 Overload 3 Over Current 4 Breaker 5 Ground fault 6 Stall 7 Jam 8 Device Over Temperature 9 Under Load 10 Impending Trip (running current greater than 115% of FLA) 11 E-Stop 12 Reserved 13 Reserved 14 Reserved 15 Other Warning - See Fault Code Table, Page 8-6.
0x0024 (36) Power Device Pole Temperature (C)
Size: Description:
0x0031
6 bytes Three signed 16 bit integers representing pole temperatures in tenths degree Centigrade
Cutler-Hammer communicating cover control or other communicating device is required to take advantage of this feature. Size: 1 byte Description: Reports the status of the circuit breaker. One byte comprised of 8 bits assigned as follows: Bit - Description 0 Circuit Breaker On 1 Circuit Breaker Tripped 2-6 Reserved 7 Circuit Breaker Unknown
0x005A (90) Average Scaled RMS Line Current (0.1 amps)
Size: Description:
2 bytes A 2 byte unsigned integer value representing the average of the three RMS line currents in tenths of an amp. A value of 65536 = 6553.6A. 2 bytes A 2 byte unsigned integer value representing the average of the three RMS line currents in amps. A value of 65536 = 65536A.
0x005B
Size: Description:
H-4
MN03902002E
0x005F
Size: Description:
2 bytes A 2 byte unsigned integer value representing the average of the three RMS pole currents in tenths of an amp. A value of 65536 = 6553.6A. 2 bytes A 2 byte unsigned integer value representing the average of the three RMS pole currents in amps. A value of 65536 = 65536A. 6 bytes Three 2 byte unsigned integer values representing the three RMS line currents in tenths of an amp. A value of 65536 = 6553.6A. 6 bytes Three 2 byte unsigned integer values representing the three RMS line currents in amps. A value of 65536 = 65536A. 6 bytes Three 2 byte unsigned integer values representing the three RMS pole currents in tenths of an amp. A value of 65536 = 6553.6A. NOTE: That for inside-the-delta applications the Line and Pole currents will differ by a factor of approximately 3 6 bytes Three 2 byte unsigned integer values representing the three RMS pole currents in amps. A value of 65536 = 65536A. NOTE: That for inside-the-delta applications the Line and Pole currents will differ by a factor of approximately 3 4 bytes 4-byte IEEE floating-point number representing the average of the three RMS pole currents in amps. NOTE: That for inside-the-delta applications the Line and Pole currents will differ by a factor of approximately 3
0x0060
Size: Description:
0x0063
Size: Description:
0x0064
Size: Description:
0x0067
Size: Description:
0x0068
Size: Description:
0x0069
Size: Description:
MN03902002E
H-5
Conguration Parameters
None of the Conguration Parameters support I/O data.
0x8001 (32769) Device Identity
Size: 14 bytes Default: See below Description: This read-only parameter contains information that uniquely identifies a device, including the following elements: Product Code 0x8200 (2 bytes) Vendor ID (2 0x0001 bytes) Serial Number A devices serial number shall be reported. This (4 bytes) value shall be unique for a particular manufacturer across all device types. Hardware Major revision shall be reported in the MSB. Minor Revision revision shall be reported in the LSB. (2 bytes) Firmware Major revision shall be reported in the MSB. Minor Revision revision shall be reported in the LSB. (2 bytes) QCPort Revision Major revision shall be reported in the MSB. Minor (2 bytes) revision shall be reported in the LSB.
0x8002 (32770) Conguration CRC
Size: 2 bytes Default: N/A Description: Used for confirmation of a devices configuration.
0x8003 (32771) Node ID
Size: 2 bytes Default: 0x0000 Description: This parameter specifies a devices Node ID. The Group ID is the Most Significant Byte and the Member ID is the Least Significant Byte.
0x8004 (32772) QCPort Operating Mode
Size: 1 byte Default: 0x00 Description: This parameter specifies a devices QCPort operating mode, as follows: Mode Description 0x00 Unconfigured 0x01 Simple System 0x02 Master/Slave 0x03 Wire Replacer 0x04 Faulted
H-6
MN03902002E
0x8005
Size: 1 byte Default: 0x03 Description: This parameter specifies the QCPort baud rate for a device as indicated below: 0x00 9600 0x01 19,200 0x02 38,400 0x03 57,600 0x04 115,200 0x05 230,400 0x06 460,800
0x8006 (32774) Slave Address
Size: 1 byte Default: 0x00 Description: This parameter specifies the address used by a Master for data transfers in the Master/Slave Data Protocol.
0x8007 (32775) Production Destination
Size: 2 bytes Default: 0x0000 Description: This parameter specifies the destination Node ID being used by an S811 Local port device communicating in the Simple System Protocol. The MSB indicates the Group ID; the LSB indicates the Member ID.
0x8008 (32776) Device ID Tag
Size: 32 bytes Default: S811 Description: This parameter specifies the 32-character ASCII string ID tag assigned to a device, pre-assigned at the factory but settable by the user.
0x8009 (32777) Production Interval (milliseconds)
Size: 2 bytes Default: 50 Description: This parameter specifies the rate, in milliseconds, at which a Local port producing device generates a Data Protocol message in the Simple System mode. A value of 0 disables this timer.
0x800A (32778) Consumption Interval (milliseconds)
Size: 2 bytes Default: 2000 Description: This parameter is the value in milliseconds to which the consumption timer is preset upon receipt of a set (value update) to any parameter on the Consumption List. Expiration of this timer shall cause the device to execute the Motor Communications Loss Behavior. A value of 0 disables this timer.
MN03902002E
H-7
0x800B
Size: 2n bytes Default: N/A Description: This read-only list specifies the n QCPort parameters that the S811 Soft Starter supports.
0x800C (32780) Production List
Size: n bytes Default: 0x000C Description: This 2n-byte read-only list specifies the n QCPort Parameters included in a devices QCPort Data Parameter 0x0001, Production Data. Adding parameters to the Production List is most conveniently done using CH Studio Component Manager configuration tool. Otherwise, setting Parameter Attribute 0x09, Production List Member, to TRUE, designates a Parameters membership in the Production List. Only Parameters supporting Attribute 0x09 are eligible for inclusion in this list. Ordering of parameters in the Production List is first on parameter data size and then sequentially by Parameter ID within parameters of like size.
0x800D (32781) Consumption List
Size: n bytes Default: 0x000B Description: This 2n-byte read-only list specifies the n QCPort Parameters included in a devices QCPort Data Parameter 0x0002, Consumption Data. Adding parameters to the Consumption List is most conveniently done using CH Studio Component Manager configuration tool. Otherwise, setting Parameter Attribute 0x09, Production List Member, to TRUE, designates a Parameters membership in the Consumption List. Only Parameters supporting Attribute 0x09 are eligible for inclusion in this list. Ordering of parameters in the Consumption List is first on parameter data size and then sequentially by Parameter ID within parameters of like size.
0x800E (32782) Languages Supported
Size: n bytes Default: N/A Description: This is a list of languages supported in the product. It consists of a list of bytes, each representing a different language. 0x00 English 0x01 Spanish 0x02 French 0x03 German 0x04 Italian
0x800F (32783) Language Selection
Size: 1 byte Default: 0x00 Description: Holds the currently selected language from the list in parameter 800E.
H-8
MN03902002E
0x8010
Size: 4 bytes Default: N/A Description: The purpose of this parameter is to provide a method for tools to access a QCPort node in a non-conflicting manner. This parameter consists of a field of 2 UINTs organized as follows: Byte Node ID Low byte Node ID High byte Lockout Time in tenths of seconds Low byte Lockout Time in tenths of seconds High byte If the above 4 bytes are 0, anyone can write to this parameter. This parameter cleared by the Clear Semaphore command that can be sent by anyone. If all 4 bytes are not 0 and a write (other than a clear) to this parameter is attempted, an error message will be returned. The parameter will be cleared when the timer counts down to 0. If the node ID field is 0, all set parameters to the node will be accepted. If the node ID field is not 0, set parameter commands to the node will only be accepted from the device having the same node ID as that contained in this parameter. Note that if the node ID is set to zero at the same time that a non-zero value is loaded to the timer, the timer will not decrement.
0x8020 (32800) Overload Trip FLA Value (amps)
Size: 4 bytes Default: Device dependent. Minimum specified value for specific S811 frame. Description: IEEE floating point value of Full Load Amps (FLA) in amps.
0x8021 (32801) Overload Trip Class Value
Size: 1 byte Default: 5 Description: Unsigned integer specifies motor trip class. Typically associated with motor protection. See Page B-3 for trip class curves.
0x8022 (32802) Percent Initial Torque (T2) (% LRT)
Size: 1 byte Default: 25 Description: Unsigned integer intended for use primarily with a soft starter. Specifies the starters initial torque (T2) in percent.
0x8025 (32805) Soft Start Time (tr) (0.1 seconds)
Size: 2 bytes Default: 20.0 sec Description: Unsigned integer sets the duration of the start ramp in tenths of a second.
0x8026 (32806) Soft Stop Time (ts) (0.1 seconds)
Size: 2 bytes Default: 0.0 Description: Sets the duration of the stop ramp in tenths of a second.
MN03902002E
H-9
0x8030
Size: 1 byte Default: 6% Description: Unsigned integer. Currents below this threshold (as a percent of FLA) that persist for greater that 2 seconds will cause an Underload fault.
0x803B (32827) Motor Jam Fault Enable
Size: 1 byte Default: 1 (Enabled) Description: Enables Phase Loss Fault detection
0x8044 (32836) Phase Imbalance Fault Enable
Size: 1 byte Default: 1 (Enabled) Description: Enables Phase Imbalance Fault detection
0x8045 (32837) Kick Start Torque (% LRT)
Size: 1 byte Default: 0 Description: 1 byte unsigned integer representing Kick Start Torque setting in Percent
0x8046 (32838) Kick Start Time (0.1 seconds)
Size: 1 byte Default: 0 Description: 1 byte unsigned integer representing Kick Start Time in tenths of seconds.
0x8048 (32840) Overload Fault Enable
Size: 1 byte Default: 1 (Enabled) Description: 0 Disables Overload Fault trip until next 24V DC power cycle. Thermal memory continues to accumulate. 1 Enables Overload Fault protection
0x8049 (32841) Phase Reversal Fault Enable
Size: 1 byte Default: 1 Description: Enables Phase Reversal Fault detection. A Phase Reversal Fault occurs when the incoming line phase rotation does not match the setting of the Phase Sequence parameter.
H-10
MN03902002E
0x804A
Size: 1 byte Default: 0 (Disabled) Description: Enables the auto fault reset function. An auto reset will be performed after the thermal memory has cooled below 75% and all other fault conditions have been corrected. This parameter is displayed as Reset Mode in the DIM
0x804B (32843) Start Method
Size: 1 byte Default: 0 Description: Unsigned integer which sets the S811s starting method: 0x00 Voltage Ramp Start 0x01 Current Limit Start 0x02 Reserved 0x03 Pump Start (option) 0x04 Reserved
0x804E (32846) Motor Communication Loss Action
Size: 1 byte Default: 0x00 Description: Determines motor action in the event of a communications timeout in network communications. This parameter only applies when the node is on line and in Auto mode. The following values are allowed: 0x00 = Auto Stop go to auto and stop 0x01 = Auto Run1 go to auto and Run1 1 0x02 = Auto Run2 go to auto and Run2 1 0x03 = Hold Last hold last state 0x04 = Local Stop go to local and stop 0x05 = Local Run1 go to local and Run1 1 0x06 = Local Run2 go to local and Run2 1 0x07 = All Stop (fault) leave in last control mode (local or auto) and stop 2 Note 1: Warning, these actions may cause the S811 to start once network communications are restored. Note 2: All Stop causes a fault and needs a reset to clear.
0x804F (32847) Motor Rated Volts (volts)
Size: 2 bytes Default: 480 volts Description: Unsigned integer set to match the incoming line voltage. This setting calibrates the Over Voltage and Under Voltage Faults
0x806C (32876) Firmware Version List
Size: 4 bytes Default: N/A Description: Unsigned integer identifies firmware versions of all firmware components of the S811. Consists of 2 2-byte elements.
0x806D (32877) Hardware Version List
Size: 2 bytes Default: N/A Description: Hardware version of all components of the system
MN03902002E
H-11
0x807C
Size: 1 byte Default: 40% Description: Unsigned integer sets the current imbalance trip level where: Percent Current Imbalance = 100 * (max deviation from average / average) Current is continuously being monitored for imbalance while the motor is energized.
0x807D (32893) Current Imbalance Fault Duration/Delay (0.1 seconds)
Size: 2 bytes Default: 0.5 Sec Description: Unsigned integer sets duration in tenths of seconds that a current imbalance condition must persist before a fault is generated.
0x807F (32895) Voltage Imbalance Fault Level (%)
Size: 1 byte Default: 6% Description: Unsigned integer sets the voltage imbalance trip level where: Percent Voltage Imbalance = 100 * (max deviation from average / average) Voltage is checked for imbalance prior to initiating a each start.
0x8080 (32896) Voltage Imbalance Fault Duration/Delay (0.1 seconds)
Size: 2 bytes Default: 0.5 Sec Description: Unsigned integer sets duration in tenths of seconds that a voltage imbalance condition must persist before a fault is generated.
0x8082 (32898) Under Voltage Fault Enable
Size: 1 byte Default: 1 (Enabled) Description: Enables Under Voltage Fault. The S811 monitors the minimum RMS value of the incoming three phase voltages. The unit will trip if the Under Voltage Fault is enabled and the minimum RMS value drops below the Under Voltage Fault Level or 80V AC, whichever is greater, for longer than the Under Voltage Fault Duration. Note that the S811 will not generate an under voltage trip when the motor is starting. The fault is only active when the unit is operating in bypass.
0x8085 (32901) Under Voltage Fault Duration /Delay (0.1 seconds)
Size: 2 bytes Default: 3.0 Sec Description: Unsigned integer sets duration in tenths of seconds that an under voltage condition must persist before a fault is generated.
H-12
MN03902002E
0x8087
Size: 1 byte Default: 1 (Enabled) Description: Enables Over Voltage Fault detection. The S811 monitors the maximum RMS value of the three phase voltages. The unit will trip with an Over Voltage Fault if the Over Voltage Fault is enabled and the maximum RMS value rises above the Over Voltage Fault Level for longer than the Over Voltage Fault Duration.
0x8089 (32905) Over Voltage Fault Duration /Delay (0.1 seconds)
Size: 2 bytes Default: 3.0 sec Description: Unsigned integer sets duration in tenths of seconds that an over voltage condition must persist before an Over Voltage Fault is generated.
0x80AD (32941) Transient Motor Control Timeout (milliseconds)
Size: 2 bytes Default: 2000 milliseconds Description: Unsigned integer. A QCPort device on the Local port is identified as a transient motor control device when the Transient Device bit (bit 6) in its Motor Control byte is SET. Transient motor control devices that are removed from the Local port will not cause a Motor Control Command Fault. A transient motor control timer is monitored to verify the presence of the transient motor control device. This timer is preset to the Transient Motor Control Timeout value each time the S811 receives another Motor Control byte with the Transient Device bit SET. When the timer times out, indicating that the device has been removed from the network, the S811 will clear and ignore that devices Motor Control byte. DO NOT SET THE TRANSIENT MOTOR CONTROL TIMEOUT TO 0. Doing so will disable the Transient Motor Control Timeout until the next Factory Reset.
0x80B4 (32948) Phase Sequence
Size: 1 byte Default: 0 Description: Unsigned integer sets the acceptable incoming line phase sequence. Phase Reversal Fault must be enabled. 0 ABC 1 ACB
0x80B6 (32950) Phase Loss Trip Level (%)
Size: 1 byte Default: 80% of Rated Voltage Description: Unsigned integer sets Percent Imbalance = 100 * (max deviation from average / average) The S811 monitors the current imbalance when the motor is running. Phase loss is an extreme case of current imbalance. The unit will trip with a motor phase loss fault if the phase loss trip is enabled and the percent imbalance exceeds the trip threshold for the trip delay and current is greater than the Overload Trip FLA.
MN03902002E
H-13
0x80B8
Size: 2 bytes Default: 0.5 sec Description: Unsigned integer sets duration in tenths of seconds that a phase loss condition must persist before a Phase Loss Fault is generated.
0x80C0 (32960) Motor Control Command Missing Timeout (milliseconds)
Size: 2 bytes Default: 2000 milliseconds Description: Unsigned integer. Every device that produces a Motor Control byte gets a timer assigned to it. When a device fails to refresh its Motor Control byte the timer will expire. When the timeout occurs, a Missing Motor Control Device Fault is generated.
0x80C3 (32963) Temperature Sensor Fault Enable
Size: 1 byte Default: 1 (Enabled) Description: Enables temperature sensor failure detection. Temperature Sensor Fault indicates that sensor has failed either by being disconnected or reporting an invalid temperature.
0x80C4 (32964) SCR Not Firing Fault Enable
Size: 1 byte Default: 1 (Enabled) Description: Enables detection of SCR (thyristor) failure to conduct current when fired (gated)
0x80C5 (32965) SCR Shorted Fault Enable
Size: 1 byte Default: 1 (Enabled) Description: Enables DC voltage level detection at the S811 Run1 terminal block input. 0 Run1 Edge Sensing 1 Run1 Level Sensing
0x80C8 (32968) Under Voltage Fault Level (%)
Size: 1 byte Default: 90% Motor Rated Volts Description: Unsigned integer. The S811 monitors the minimum RMS value of the incoming three phase voltages. The unit will trip if the Under Voltage Fault is enabled and the minimum RMS value drops below the Under Voltage Fault Level or 80V AC, whichever is greater, for longer than the Under Voltage Fault Duration. Note that the S811 will not generate an under voltage trip when the motor is starting. The fault is only active when the unit is operating in bypass.
H-14
MN03902002E
0x80C9
Size: 1 byte Default: 110% Motor Rated Volts Description: Unsigned integer. The S811 monitors the maximum RMS value of the three phase voltages. The unit will trip with an Over Voltage Fault if the Over Voltage Fault is enabled and the maximum RMS value rises above the Over Voltage Fault Level for longer than the Over Voltage Fault Duration.
0x80CA (32970) Output Relay 1 Conguration
Size: 1 byte Default: 2 Description: Unsigned integer. Configures functionality of Relay 1: 0 Faulted 1 Not Faulted (Ready) 2 In Bypass 3 Not In Bypass (Starting) 4 Motor Energized 5 Motor Not Energized
0x80CB (32971) Output Relay 2 Conguration
Size: 1 byte Default: 0 Description: Unsigned integer. Configures functionality of Relay 2: 0 Faulted 1 Not Faulted (Ready) 2 In Bypass 3 Not In Bypass (Starting) 4 Motor Energized 5 Motor Not Energized
0x80CC (32972) Overload During Start Enable
Size: 1 byte Default: 1 (Enabled) Description: 0 Overload disabled during start. Thermal memory is set to 80% when bypass entered. 1 Overload enabled during start
0x80CD (32973) Pump Stop Time (0.1 seconds)
Size: 2 bytes Default: 120.0 sec Description: Unsigned integer. Sets the Stop Ramp Time for S811s with the pump control option.
0x80CE (32974) Termination Resistor Enable
Size: 1 byte Default: 1 (Enabled) Description: Connects termination resistor at S811 Local port (CH1).
MN03902002E
H-15
H-16
MN03902002E
MN03902002E
H-17
H-18
MN03902002E
Company Information
Eatons electrical business is a global leader in electrical control, power distribution, and industrial automation products and services. Through advanced product development, world-class manufacturing methods, and global engineering services and support, Eatons electrical business provides customer-driven solutions under brand names such as Cutler-Hammer, Powerware, Durant, Heinemann, Holec and MEM, which globally serve the changing needs of the industrial, utility, light commercial, residential, and OEM markets. For more information, visit www.EatonElectrical.com. Eaton Corporation is a diversied industrial manufacturer with 2005 sales of $11.1 billion. Eaton is a global leader in electrical systems and components for power quality, distribution and control; uid power systems and services for industrial, mobile and aircraft equipment; intelligent truck drivetrain systems for safety and fuel economy; and automotive engine air management systems, powertrain solutions and specialty controls for performance, fuel economy and safety. Eaton has 60,000 employees and sells products to customers in more than 125 countries. For more information, visit www.eaton.com.
Eaton Electrical Inc. 1000 Cherrington Parkway Moon Township, PA 15108-4312 USA tel: 1-800-525-2000 www.EatonElectrical.com
2006 Eaton Corporation All Rights Reserved Printed in USA Publication No. MN03902002E/CPG June 2006 Revision 5