Professional Documents
Culture Documents
Us Airways
Us Airways
Training Notes by Eric Parks Copyright 1999 - 2004 Eric Parks Disclaimer: NOT approved by US Airways Airbus A320 Flight Training Dept. (in fact it isnt approved by anybody except the pilots that use it!) For study only, use at own risk, last update
Fraud
TABLE
OF
CONTENTS
TABLE OF CONTENTS.....................................................................................................................................2 LIMITS....................................................................................................................................................................4 SYSTEMS...............................................................................................................................................................6 ICE & RAIN PROTECTION.........................................................................................................................................6 ELECTRICAL .............................................................................................................................................................8 FIRE PROTECTION ..................................................................................................................................................13 FUEL.....................................................................................................................................................................17 PNEUMATICS , AIR CONDITIONING & PRESSURIZATION .............................................................................................23 HYDRAULICS , BRAKES & LANDING GEAR ..............................................................................................................29 FLIGHT CONTROLS .................................................................................................................................................36 OXYGEN ...............................................................................................................................................................55 POWERPLANT ........................................................................................................................................................56 APU ...................................................................................................................................................................59 EQUIPMENT............................................................................................................................................................61 INSTRUMENTS........................................................................................................................................................62 NAVIGATION SYSTEMS ............................................................................................................................................72 COMMUNICATIONS.................................................................................................................................................79 AUTO FLIGHT SYSTEM ..........................................................................................................................................82 TAKEOFF...........................................................................................................................................................112 WHAT DOES SRS DO FOR YOU?............................................................................................................................113 RTO REJECTED TAKEOFF ................................................................................................................................113 V1 CUTS............................................................................................................................................................113 APPROACHES & LANDING.........................................................................................................................115 ILS APPROACHES ................................................................................................................................................119 RNAV (LNAV- VNAV) APPROACHES .............................................................................................................122 VOR AND LNAV RNAV APPROACHES ..............................................................................................................123 ENGINE-OUT APPROACHES ...................................................................................................................................124 VISUAL APPROACHES ...........................................................................................................................................125 GO AROUND........................................................................................................................................................126 LANDING.............................................................................................................................................................127 A TO Z - ABBREVIATIONS & ACRONYMS............................................................................................129 COMPANY STUFF...........................................................................................................................................133 LOGBOOK STUFF..........................................................................................................................................134
22/05/12
Fraud
Authors notes: These notes are not intended to be a comprehensive look at every aspect of the A319/320/321. I only intend them to cover the basics. They assume an already high level of experience with advanced aircraft systems. I hope they help in studying for initial or recurrent or as a quick reference during line operations. They are written from the viewpoint of a US Airways line pilot because that is who I am. I have included what I find helpful. If you find something that you feel should be included or corrected please let me know as I am always seeking to improve the product. Eric Parks, [email protected] Note: Copy shops may distribute and charge for cost of copies alone, no charge for the content. Permission is given to distribute these notes under the following conditions: Nothing may be charged for the notes No changes may be made without express consent of the author Authors copyright must be included
22/05/12
LIMITS
(memory items in bold italics) Weight Limits Max Ramp: Max Takeoff: Max Landing: Max Zero Fuel: Min Weight Operation Limits Max 90 crosswind component for Takeoff 38 Max 90 crosswind component (for landing 38 Limiting tailwind component for takeoff and landing: Max operating altitude: Speed Limits Max operating speed (VMO): Max operating speed (MMO): Max Flap Alt Max Gear Placard 20,000 Extend 250 Max Gear Alt Retract 220 350 KIAS .82M 25,000 Extended 280 /.67 below 20,000 ft.: 250 KIAS 270 KIAS 3 185 KIAS 195 KIAS FULL 177 KIAS 190 KIAS 29 knots gusting 33 knots gusting 10 knots 39,000 ft. A319 75 900 kg 75 500 kg 62 500 kg. 58 500 kg. A320 75 900 kg 75 500 kg 64 500 kg. 61 000 kg 37 230 kg A321 93 400 kg 93 000 kg 77 800 kg 73 800 kg
Turbulence Penetration A319/320 A321 Max Flap / Slats (VFE): Model Position: A319/320 VFE A321 VFE
at or above 20,000 ft.: 275 KIAS / .76M 300 KIAS / .76M 1 230 KIAS 235 KIAS 1+F 215 KIAS 225 KIAS 2 200 KIAS 215 KIAS
Ice & Rain Protection Engine anti-ice must be on during all ground and flight operations when icing conditions exist except during climb and cruise when the temperature is below: -40 C SAT.
Airbus A319, A320, A321 Notes Icing conditions exist on ground: Icing conditions exist in flight: Fuel USABLE FUEL
OUTER TANKS INNER TANKS CENTER TANK
Fraud
TOTAL
VOLUME WEIGHT
liters US Gallons KG LB
Maximum imbalance between left and right wing fuel tanks: 530 kg Autopilot / Autoland After Takeoff (if SRS is indicated) Autoland max winds: Tailwind: Crosswind other than CAT II/III: Headwind: Non-memory limits (yeah, right!) Max tyre speed Max window open speed (who is going to open it?) Max windshield wiper operations speed (VWW) Max continuous load on generator Max continuous load on TRU Max brake temp for takeoff APU Limitations Electrical power Battery restart 1 Air conditioning pack 2 Air conditioning packs Ground operations Up to 39000 Up to 25000 Up to 20000 Up to 15000 Up to 8000 195 kts. 200 kts. 230 kts. 100% (90 KVA) 200 A 300 C 100 ft. AGL 10 knots 20 knots 30 knots
22/05/12
SYSTEMS
Note: pb stands for pushbutton (NOT peanut butter!) and there are lots of em!
Engine Anti-ice Engine Anti-Ice ducting is independent of wing ANTI-ICE. Engine Anti-Ice valves will open automatically on loss of electrical power. They close with air pressure
Fraud
available. Engine limits ( N1 Limit - Idle N1 ) are automatically reset when Engine Anti-Ice selected and continuous ignition is automatically turned on for that engine as well. Probe and Mast Heat / Window Heat / Rain Removal -
All heat is turned on at low power on ground after the first engine start. In flight all heat automatically goes to High. Can turn on manually on ground before engine start by pressing pb to ON. Deselect to Auto after second engine start. Note: when on ground a windshield (or window) heat fault may be given due to heating by the sun. Cool the cockpit (or stow shades) and reset the WHC circuit breaker.
22/05/12
Electrical
All normal electrical power shifts automatically except the External Power which must have the EXT PWR pushbutton selected to supply power to the AC bus tie. Normal priority for AC power is: (work across ELEC panel from GEN 2) 1) 2) 3) 4) 5) On side engine generator External Power APU Off side engine generator Emergency Generator (RAT) 6) Batteries The only way to power both AC busses from a single power source is through the AC BUS TIE. The APU and EXT PWR both feed the AC BUS TIE. Both AC busses connect to the AC BUS TIE as needed. APU will automatically power AC unless the EXT PWR or ENG GEN is on. If both IDGs are available then the AC busses will not be connected to the AC BUS TIE. If only one ENG GEN (no APU or EXT PWR) is available the opposite AC bus will connect to it through the AC BUS TIE.
The Electrical system is divided into two main branches. Both AC and DC are normally separated into two branches with Engine 1 driving IDG (integrated drive generator) 1 and IDG 1 feeding AC BUS 1. AC BUS 1 then feeds DC BUS 1 through TR 1 (transformer rectifier). The same happens on side 2. As long as each engine IDG is available then the two sides remain electrically isolated. If there is a loss of power on an AC bus then the remaining powered bus will automatically power the unpowered AC bus through the AC BUS TIE. If the APU is then started it will automatically power the bus tie and the failed AC bus.
Fraud
The AC BUS TIE will then be isolated from the normal powered bus. IDG should not be disconnected when engine not turning (operating or windmilling) and the IDG disconnect should not be pressed more than 3 seconds. IDG can only be reconnected on the ground. In case of TR failure the DC busses can be automatically connected through the DC BAT BUS. Two batteries are installed. Battery charging is automatic and is controlled by the BCL (Battery Charge Limiter). The BCL connects the battery to its respective DC BAT BUS during battery charging and during APU start. The batteries have an automatic cut-off logic to prevent complete battery run-down when the aircraft is unpowered and on the ground. This will shut off the batteries at about 22,5v capacity to ensure APU start after overnight. Min Battery voltage is 25,5v. Check battery voltage with the BAT switch OFF. To charge batteries turn them on by pressing their respective pbs and connecting external power. A 20 min. charge is required if BAT voltage is not enough. Part of the normal procedures for the Originating Checklist call for the check of both batteries to make sure that they are charging properly. Turn off both batteries and then turn them back on. Watch on the ECAM ELEC page to see that both batteries have initial current charge rates after 10 seconds of less than 60 amps and decreasing. If both Main AC busses lose power and the airspeed is 100 kts. or more the RAT will automatically deploy. The emergency generator will then power AC ESS BUS and DC ESS BUS. During the 8 seconds it takes the RAT to deploy and supply power, the batteries will supply the ESS busses (not their shed busses) and the red FAULT light on the EMER ELEC PWR panel will be on during those 8 seconds. The RAT emergency generator is lost at less than 125 kts and ND1 and MCDU1 will go out at that time due to loss of AC shed bus. On landing the DC BAT bus is automatically connected to the batteries when airspeed drops below 100 kts. When all AC is lost including the RAT emergency generator BAT 1 will supply AC ESS through the static inverter and BAT 2 will supply DC ESS. When the speed drops below 50 kts. the AC ESS bus is shed and power is lost to remaining CRTs (PFD1, ECAM upper). Note: min. RAT speed is 140 kts, RAT will stall out at less than 125 kts. AC BUS 1 normally supplies power to AC ESS and DC BUS 1 which eventually feeds DC ESS. If AC BUS 1 fails the pilot may press the AC ESS FEED pb to ALTN. This will put the AC ESS BUS on its alternate source, GEN 2 through AC BUS 2. AC Essential Feed will not automatically switch. This is to prevent a bus short on the AC ESS BUS from then also damaging the GEN 2 bus complex if it has already caused damage to the GEN 1 bus complex. ECAM will direct whether to actually repower AC ESS or to leave it unpowered. AC BUS 2 will also supply power to DC ESS BUS from DC BUS 2 and DC BAT BUS when the AC ESS FEED pb is selected to ALTN. If TR1 fails the DC BAT BUS and DC BUS 1 will become automatically powered by DC BUS 2 which will automatically connect to the DC BAT BUS.
22/05/12
Fraud
APU will carry all busses on ground but will not supply main galley shed busses in-flight. In-flight if only one generator is supplying entire system then part (321: all galley power) of the galley load and passenger in-seat power supply is shed.
GEN 1 Line If there is smoke in the avionics compartment the amber SMOKE light will come on in the GEN 1 LINE pushbutton.
The procedure will call for the pilot to press the pb. This will open the GEN 1 line contactor and depower AC bus 1. GEN 2 will then automatically pick up AC BUS1 through the AC BUS tie. However, GEN 1 will still be powering two wing fuel pumps, one in each wing inner tank. Note: this is not the complete smoke procedure, just the beginning that deals with the GEN 1 LINE pb. In loss of all AC (RAT only) emergency the APU is allowed 3 min. for start after EMERG GEN connects. The APU will not start in-flight when on BAT only (this is due to the DC BAT BUS being disconnected during Electrical Emergency 10 22/05/12
Fraud
configuration above 100 kts.). Lights available in loss of all AC emergency are Capt. instrument lights, F/O dome light (if on DIM or BRT) and compass/ice light If any generator is operating at more than 100% rated load the GALY & CAB (or GALLEY) pb will illuminate amber FAULT. You will be directed to select OFF which will then load shed by offloading the main galley, secondary galley and the in-seat power supply.
Circuit breakers are color coded. Green are monitored by ECAM. All other colors are not monitored. The ECAM will display C/B TRIPPED ON OVHD PNL (or REAR PNL) if a green monitored breaker is tripped for more than a minute. Yellow breakers are pulled during the procedure for flight on battery power only. Red capped breakers are NEVER pulled in flight. Red caps are installed on the wing tip brakes circuit breakers to prevent loss of flap asymmetry protection. All circuit breakers have a letter (vertical) and number (horizontal) code.
When on the gate with normal APU or EXT PWR the GEN 1 & 2 amber FAULT lights will normally be the only amber FAULT lights on in the overhead panel (with packs ON). 11 22/05/12
Fraud
When shutting down the APU and turning off BATTs allow 2 min. after APU Green AVAIL light goes out to allow time for APU flap to close Batteries must always be on when APU is running for fire protection.
12
22/05/12
Fire Protection
Both engines and the APU each have two identical loops, A & B and a computerFDU (Fire Detection Unit). A fire warning is given when both loops reach the proper overheat condition. If one loop fails the other loop is able to generate the warning by itself. A fire warning is given if both loops fail within 5 seconds of each other. Engines have sensing elements in three sections; pylon nacelle, engine core and fan section. APU has one sensing element in APU compartment. The engines each have two extinguishers, the APU one. APU APU fire on ground will auto shutdown, sound nose wheel well horn and APU FIRE light will illuminate on external interphone panel. APU fire in-flight must be manually shutdown (will not auto shutdown) and extinguished. There is a red disc on the aft fuselage to show thermal discharge for the APU fire bottle. Note: APU will auto shutdown in air for other than fire (go figure). The forward cargo compartment has two smoke detectors and the aft has four (319,320). Agreement of two smoke detectors on a loop will give warning. If one smoke detector fails the system remains operational on the remaining detector. There is one extinguisher bottle for fore and aft compartments with one nozzle forward and two nozzles aft. If cargo SMOKE warning is given an isolation valve will close and the extraction fan will stop. Cargo smoke gives: CRC, Master Warn light and Cargo SMOKE light.
Fraud
ENG fire test (7 items 4 reds) : ENG 1 Test: ENG FIRE pb illuminated (red) SQUIB and DISCH lights illuminated (2) MASTER WARN illuminated (2) (red) CRC aural chime ENG 1 FIRE warning on E/WD (red) ENGINE page on SD FIRE light ENG 1 (on ENG panel) illuminated (red)
APU fire test: (BAT only 2 items 1 red, AC 6 items 3 red) APU FIRE Test press and hold (APU will not shutdown during test) APU FIRE pb illuminated (red) * SQUIB and DISCH light illuminated * MASTER WARN lights illuminated (2) (red) CRC aural chime APU FIRE warning on E/WD (red) APU page on SD * BAT only (when doing Safety and Power On checklist on Battery only, no External power)
14
22/05/12
Fraud
(work down panel with 2,1,2,1,2 sequence two on FIRE, one on HYD, two on FUEL, one on ELEC, two on AIR COND) FIRE HYD FUEL ELEC AIR CONDSilences CRC, Arms squibs Closes hydraulic fire valve Closes low pressure fuel & engine IDG fuel return valves Trips ENG GEN Closes engine bleed & pack flow valves (2) (1) (2) (1) (2)
(work down panel with 3, 0, 2,1,2 sequence)Silences CRC, Shuts down APU, Arms squib Closes low pressure fuel valve & APU fuel pump off Trips APU GEN Closes APU bleed & Crossbleed valves (3) (2) (1) (2)
Cargo Smoke Detector test Press & release button for test. You should get: DISCH amber lights illuminate. SMOKE red lights illuminate MASTER WARN light illuminate CRC CARGO SMOKE on E/WD
This test will run twice after you select it once to test both channels. Note: DISCH amber lights only on first test. If the CARGO SMOKE bottle is fired the indications you can expect are: Red SMOKE light remains on (smoke & bottle discharge are trapped) Both amber DISCH lights will come on and remain on (only one bottle)
15
22/05/12
Fraud
16
22/05/12
Fuel
Surge tank Outer wing Inner wing tank tank 691 kg 5435 kg Center tank 6476 kg Inner wing Outer wing tank tank 5435 kg. 691 kg Surge tank
Fuel Philosophy: Fuel in center last, fuel in center burned first. Takeoff on center tank prohibited. The center tank pumps run at a higher override pressure (A319, A320) so the center tank fuel will be burned before the wing tank fuel will be even though center and wing pumps are both providing fuel pressure to the manifold at the same time.
Fraud
If both pumps in same tank fail, only the inner wing tanks can suction feed. Center tank fuel would be unusable. APU fuel is drawn from the left fuel manifold. The APU normally uses the tank pump pressure but has its own fuel pump that it will use if no other fuel pump pressure is available.
Losing one center pump requires opening crossfeed valve (one ECAM chime) Losing one inner tank pump just requires turning off the pump switch (no chime) Losing two center tank pumps will make any remaining center fuel unusable (no suction feed). Losing two inner tank pumps will put that wing on gravity (suction) feed. There is a chart to determine safe altitudes for gravity feeding in the QRH.
18
22/05/12
Fraud
Normally fuel is run in Auto mode. This will run the wing tanks continuously and the center tank on a schedule. The Auto mode schedule for the center tank is to run the center tank pumps any time there is fuel in the center tank except when the slats are extended. Exceptions to the Auto schedule: After engine start the center tanks will run for at least two minutes for a test run even if the slats have already been extended. If slats are not extended pumps will continue to run as normal until they are extended. The pumps will restart again after takeoff when the slats are retracted. After the center tanks run dry the pumps will continue to run for 5 more mins. If IDG return fuel fills the outer wing tank the extra fuel will spill over into the inner wing tank. If the inner wing tank fills completely up then the center tank pump on that side will be automatically turned off to allow wing tank fuel to be burned until 500 kg has been used. Then the center tank pump will turn on again. This prevents surge tank spillage.
The fuel in the outer wing tanks will gravity feed through two transfer valve openings when inner wing tank fuel level reaches 750 kg. 19 22/05/12
Fraud
When either wing inner tank reaches the 750 kg level a signal is sent to latch open all the transfer valves in both outer wing tanks. This is a total of 4 valves, 2 in each outer wing tank. The transfer valves will remain open for the rest of the flight and will close on the next refuel operation. If fuel is sloshed during climb or descent it is possible for the transfer valves to be opened early due to a LO LEVEL alert. An ECAM caution is given if during Auto mode the center tank has more than 250 kg of fuel while the left or right wing tank has less than 5000 kg. of fuel per wing. This would indicate that the normal Auto schedule was not being followed. The Crossfeed pb is normally extinguished when the valve is closed. It will show blue ON when selected on and green OPEN when fully open. There are two full levels for the inner wing tanks, a fueling full and an operational full. The fueling full is less than the operational full and that allows the extra IDG fuel room to collect in normal circumstances without triggering the center tank pump turn-off for IDG return fuel. Note: In Auto the center tank pumps run all the time if center tank fuel is present so with all fuel pumps on if you are on the gate with APU running (slats up) you will be using center tank fuel. If operating in Manual mode the crew must ensure that the center tank pumps are off when the wing tanks are completely full or when the center tank is empty. Note: Unusable fuel is shown with a half amber box around the fuel quantity on ECAM. If the fuel quantity is in a degraded mode the ECAM fuel quantity will have amber dashes through the last two digits. Refuel is shown on upper ECAM memo when refueling door is open.
20
22/05/12
Fraud
Refueling Manual refueling: wing tanks first, then center tank No electrical transients during refueling. No APU Start or Stop during refueling.
21
22/05/12
Fraud
Note: IDG return fuel is added to the wing tank as there is no outer tank on the A321. Note: There is no ECAM OUTR TK FUEL XFRD memo on the A321 as there is no outer or inner wing tank (all fuel in one wing tank). The A321 has two Additional Center Tanks that will automatically feed to the Center tank when the Center tank burns down to a certain level. The Additional Center Tanks do not have pumps but use cabin air pressure to feed the center tank through transfer valves. The ACT 2 (aft tank) will transfer fuel first followed by the ACT1. All fuel transfer is done automatically in the normal mode of operation. The automatic fuel transfer from ACT to Center Tank is noted on the ECAM as a green triangle between the ACT fuel indicators. An additional pb has been added to the FUEL panel to control the ACT fuel transfer. Yes, you guessed it, the normal mode is AUTO (are we seeing a pattern here?). In AUTO mode the ACT pb allows automatic control of the fuel transfer after slat retraction when in-flight. Fuel transfer will begin from the ACT 2 when the center tank is no longer full. Transfer will continue until either the center tank is full or both ACTs are empty. After ACT transfer starts if the center tank becomes full transfer will stop until the center tank burns down sufficiently and the transfer process will automatically restart. ACT 1 (forward) ACT 2 (aft) An amber FAULT light will illuminate in the ACT pb if the center tank has less than 6,614 lbs. of fuel and one ACT has more than 250 kg. of fuel which would indicate that the AUTO schedule was not being followed. If the ACT pb is selected to FWD then all ACT fuel will be manually transferred forward to the center tank using the ACT transfer pump, which is a backup pump that can pump from either ACT. This backup ACT XFR pump runs at a low volume and may not be able to transfer all fuel at higher altitudes (FL270 and above) or supply as fast as the engines are burning. Chapter 21 will specify best procedures for complete transfer of fuel in case of ACT transfer FAULT. It is normal to have fuel being transferred from the ACTs to the Center tank and from the Center tank to the Wing tanks at the same time. On the A321 theres a whole lotta transferring goin on. Please note that in order to feed an engine from the opposite wing you must still open the fuel crossfeed valve. In normal AUTO operation the fuel procedures are the same and fuel transfer operation is transparent to the pilot. Note: For the A321 all fuel is burned from the Wing tanks. Fuel must be transferred to a Wing tank for it to be available for use by the engines. There is no ECAM CTR TANK FEEDG memo as the A321 never feeds from the Center Tank. Note: For A321: if center tank is not full then do not takeoff with fuel in an ACT Note: on the SD FUEL display the left ACT is #1 (forward) and the right ACT is #2 (aft). Gee, why not just display them as fore and aft?
22
22/05/12
The valve will also automatically close pneumatically when: Low pressure Reverse flow
And is electrically closed when: ENG BLEED selected off ENG FIRE pb selected
The APU bleed will close for leaks The APU is ready for bleed when reaching 95% for two seconds or 99.5%. The AVAIL light will show in the APU start pb and green APU AVAIL will show on EWD display when APU is available for use. The crossbleed valve can be operated in automatic or manual mode. There are two electric motors for the valve, one for each mode. In automatic mode the crossbleed valve opens automatically when using APU bleed air. During normal operation the crossbleed is closed to isolate the two engine bleeds.
Fraud
The crossbleed is manually set OPEN during the engine crossbleed start procedure. The leak detection system uses a single loop for the pylons and APU to detect hot air temps associated with duct leaks. Dual loops are used for the wings. If both of the dual loops detect a leak a warning is given, unless there is a fault on one, then only one loop is required to give a warning. If a leak is detected: The engine bleed air valve (APU bleed air valve) on that side is closed Associated ENG (APU) BLEED FAULT light comes on Crossbleed valve closes (except during engine start) Left wing leak only APU bleed air valve closes (except during ENG start)
Air Conditioning
Packs
Airbus Gotcha: Do not use external conditioned air when using packs .
Unfortunately, there is no cockpit indication of external air connected! You can turn off the cabin fans pb and if air continues to blow from the vents then external air is connected. Pay attention here, many new Airbus pilots fail to understand the way the Zone Temp system works. If you are familiar with the 737-400 this is very similar. Both packs are feeding all three zones. Whichever zone is commanding the coldest temperature will drive BOTH packs to that temp. Hot air is then added to any other zone that is commanding a higher temp. This hot air is called trim air and is how the zone temp system controls temperatures in three zones with only two packs. There are three air conditioning zones: Cockpit, FWD Cabin and AFT Cabin. The zones are controlled by having the packs deliver all air at the lowest temp requested by any of the three zones. Then hot air is added through the trim air valves to the other two zones as needed to meet temp requirements. A/C zone temp selectors have a range of: Cold 18C/64F, 12 oclock 24C/76F, Hot 30C/86F The AC pack can bypass bleed air around the air cycle machine (ACM) if the ACM fails and run the bleed air through the primary heat exchanger directly. This allows the pack to operate as a simple heat exchanger with reduced pack flow. Pack flow will revert to HI during single pack operation or APU bleed source regardless of selector position. The Zone controller can override pilot selected pack flow (HI, NORM and LOW) as needed to meet demands. It can also command higher APU speed or engine idle as needed. One Zone controller with two channels. Failure of the primary channel will result in fixed temperature at 24C with no optimization. Failure of the secondary as well will result in a fixed temp of 20C pack 1 and 10C pack 2. 22/05/12 24
Fraud
One Pack controller per pack. Two channels per controller. If primary fails the secondary pack air flow will be fixed at the pre-failure setting. No further optimization is available. Further failure of the secondary will result in a fixed pack outlet temp of 15C. Pack controllers also regulate the cooling air flow through the ACM. During takeoff and touchdown the controllers close the ram air inlet flaps to prevent ingesting debris. Note: The Airbus 319/320 can be dispatched with one pack INOP up to FL310 or below (see MEL) RAM air RAM air is available for cabin ventilation in the event of loss of pressurization or smoke removal. When the RAM AIR pb is selected the RAM air inlet opens. When pressurization differential is less than 1 psi. the outflow valve will open to 50% to allow exhaust. If above 1 psi. then the outflow will remain normal.
Pressurization
There are two identical independent pressurization systems. Control is normally fully automatic. The system has one Cabin Press panel, two controllers (CPC), one outflow valve and two safety valves. The outflow valve has three DC motors: Primary, Backup and Manual. Controllers can operate in automatic, semi-automatic and manual modes. Automatic: Controller automatically takes the destination field elevation from the aircraft database. The entire pressurization schedule is optimized by the system. Semi-automatic: If the database is not available for some reason the pilot can select the landing elevation from the LDG ELEV knob by pulling the selector out of the AUTO detent and turning to the needed value. Manual: Normally, the controllers take turns controlling by swapping after each leg. If the active controller fails the backup automatically takes over. If both automatic systems fail the pilot may control manually by pressing the CABIN PRESS MODE SEL to MAN. The primary and backup outflow valve motors are depowered and the manual motor is activated. Now the pilot can select vertical speed on the cabin using the MAN V/S CTL switch. Abort mode: If the aircraft returns after takeoff the system will reset to departure field elevation. Ditching pb: The Ditching pb will close all exterior openings below the flotation line. This pb is also used during deicing to prevent deicing fluid from entering the aircraft. 25 22/05/12
Fraud
Airbus Gotcha: on ground with Ditching pb ON and all doors closed &
external low pressure connected a pressurization differential will build. Note: If the pilot suspects that pressurization is not performing normally but has not yet failed press the MODE SEL pb to MAN for 10 secs. then return to AUTO. This will cause the systems to swap. Depressurization: When cabin exceeds about 11,000 the cabin may illuminate and Exit and all cabin signs illuminate automatically. Masks will automatically drop at 14,000 cabin altitude.
Ventilation
The avionics are cooled through a system that uses two openings and two electric fans. Conditioned air is also available for backup if needed. Yes, a computer controls the whole thing (sigh).The intake is on the lower left side below the cockpit. A blower fan draws air in and the extract fan on the right side exhausts the air out from a port below the cockpit on the lower right side.
26
22/05/12
Fraud
Open configuration: Only for ground operations, both the inlet and outlet vents are open and both fans operate. Note: during heavy rain operations on ground select EXTRACT pb to OVRD with both packs operating. This will prevent rain from entering the avionics bay. Return to normal auto operation once airborne Closed configuration: In-flight mode and very cold ground operations. Both vents are closed, however both fans run to circulate air past skin heat exchangers that are cooled by low outside skin temperatures. Some air exhausted through cargo underfloor. Also known as the infamous Skin Cooling Config. Intermediate configuration: Only for use in-flight when warm, same as closed except reduced opening to allow some additional exhaust of cooling air. Abnormal configuration: Fault is detected in either the BLOWER or EXTRACT fan. Blower fan is off but Extract remains ON. Similar to closed except air conditioned air is added to the circulated air. ECAM will direct configuration. Smoke configuration: If smoke is detected in avionics both the BLOWER and EXTRACT fan will have amber FAULT lights on and the GEN 1 LINE pb (on EMER ELEC PWR panel) has amber SMOKE illuminated. Selecting BOTH fans to OVRD will cause the blower to stop but the extract to continue operating. Conditioned air is added to attempt to cool and clear the smoke, then exhausted overboard.
27
22/05/12
Fraud
28
22/05/12
Green is the heavy system with landing gear, flaps/slats, nosewheel steering and Normal Brakes. Blue is basically for redundancy with the only unique items on it being L & R spoiler 3 and the Emergency Generator which are backup items themselves. Yellow provides the ground service items of parking brake and cargo door and also helps power flaps. The RAT and Yellow electric pumps do not normally run during flight. The Yellow electric pump will automatically come on when a cargo door is operated. Other Yellow system functions are inhibited when automatically activated by a cargo door. A hand pump is provided on the Yellow system to provide the ability to open cargo doors with no electric power on the aircraft. Blue electric operates all the time in-flight and on the ground when at least one engine is operating. The RAT hydraulic pump is for emergency use only and will only deploy manually for hydraulic problems. For electrical problems it will deploy automatically above 100 kts. with loss of all AC. Note: Min RAT speed is 140 kts. with A319/321 and modified A320 RATs stalling at less than 125 kts.
Fraud
The PTU is able to transfer power but not fluid. It transfers power between the Green and Yellow systems (the two with the engine pumps and heavy consumers). The PTU can transfer power in either direction and is activated when a 500 psi differential is sensed between Green and Yellow. The PTU can also be powered on the ground by the Yellow electric pump to power Green hydraulic. Allows Yellow electric pump to power Green on ground (for example to retract slats on ground). The PTU is inhibited when First engine is being started. This is identified as when the nosewheel steering disconnect pin is in and one ENG MASTER switch is ON. (PTU operation is tested on second engine start) Cargo doors are operated (Yellow electric normally powers cargo doors, this prevents draining low output of electric pump or accidentally powering Green Hydraulic) Parking brake is ON and only one ENG MASTER switch is ON PTU pb is off The engine pumps (Green and Yellow) each have Fire Shut Off Valves that close when the Engine Fire Pushbuttons are selected open. Note: If a cargo door is operated and then the 2nd engine is started within 40 seconds a PTU fault message may be given (I assume due to inhibition during test period)..
Brakes
The brakes are carbon, multidiscs actuated by two independent systems, Normal and Alternate. The normal brakes are powered by the Green hydraulic system. Normal brakes are available when: 30 22/05/12
Airbus A319, A320, A321 Notes The A/SKID & N/W STRG switch is ON Green hydraulic pressure is available The parking brake is OFF
Fraud
A BSCU (Brake and Steering Control Unit) controls all normal braking functions (anti-skid, autobrakes and brake temps.).
Anti-skid is deactivated below 20 kts. Anti-skid may or may not be available when on alternate brakes. If antiskid is inop. then alternate brakes use 1000 psi max to prevent blowing tires.
31
22/05/12
Fraud
The alternate brakes are powered by the Yellow hydraulic system and will automatically become selected if Green hydraulic is insufficient for normal brakes. Yellow brakes have the same capabilities as normal brakes except for autobrake capability.
Alternate brakes can be used with or without anti-skid. Anti-skid during alternate brakes is inoperative when: Electrical power failure BSCU failure A/SKID & N/W STRG switch turned off Brake pressure supplied by Yellow accumulator only
Parking brake disables all other brake modes (319, 320 only). Parking brake is on Yellow system.
32
22/05/12
Fraud
A pressure indicator on the instrument panel indicates Yellow accumulator pressure and Yellow left and right brake (parking brake) pressure on three needles. Accumulators maintain good parking brake pressure for at least 12 hrs. The cargo door operation will restore parking brake (Yellow system) pressure. Autobrakes are available on Normal Brakes (Green system) only. Hold pb for at least one second. LO mode delays for 4 seconds after touchdown. MED mode delays for 2 seconds. MAX has no delay. Do not use MAX for landing, MAX is takeoff only . The Green DECEL light in the auto brake pbs indicates actual deceleration is within 80% of the selected rate (does not indicate that the autobrake is activated). Autobrakes activate when ground spoilers are extended. On takeoff they are not armed until 72 kts. 2 SECs are required for Autobrakes. Brake Fans are installed in the main gear hubs. They will indicate an amber HOT when the brakes are 300 C or more. Brake temps are shown on the ECAM WHEELS page. An arc will appear above the hottest brake temp. If brake temp is above 300 C then the temp will turn amber. The brakes must be cooled below 300 C before takeoff. Pilot must manually select brake fans on. Note: Delay selecting Brake Fans on taxi in for at least 5 mins. or until at gate. Carbon brakes actually wear better when heated, however if turn time is short or if brakes will exceed 500 then cool immediately. Fans should only be used to cool to about 250 C Hot Brakes Maintenance action is required if there is: 150 C difference in brake temps on the same strut and one brake 600 or greater or 60 or less a mean 200 C difference between different trucks fuse plug melted brake temp exceeds 900 C (800 C, A321) 33 22/05/12
Fraud
Avoid use of the parking brake when brakes are 500 C or above if able. Do not set Parking Brake ON in flight.
34
22/05/12
Fraud
Landing Gear
The Airbus Landing Gear Has enclosed gear bays Is held by mechanical uplocks Uses manual extension by gravity Has no mechanical or visual check for gear position Uses autobraking on the mains during retraction Has a brake band in the nose gear well Is hydraulically locked out from operation above 260 kts. The LGCIU controls the Airbus landing gear operation. The SD will show 2 green down triangles on the WHEELS page for each gear down and locked. There are also gear indicators next to gear handle. Any green triangle (at least one out of three possible) for a gear confirms the gear down and locked. One green and two red triangles for a gear still indicates down and locked. Red shows gear in transit and no triangle indicates gear uplocked. The gear doors will remain down after manual gravity extension. The gear lights by the gear handle are powered through (hard wired) LGCIU 1, if LGCIU 1 is not powered the lights will not operate . The gear handle has a red down arrow that will illuminate if gear is up with flaps 3 or FULL below about 700 (landing configuration). ECAM will alert .
35
22/05/12
Fly-by-wire, no feedback except for rudder and horizontal stab trim Two ELACs Elevator, aileron and stabilizer control Three SECs Spoiler and standby elevator and stabilizer control Two FACs Electrical rudder control (other warning functions also provided) FCDCs (Flight Control Data Concentrators) process information from ELACs and SECs and send data to the EIS and CFDS. Pitch Controlled by elevators and horizontal stab. Electrically controlled by ELAC or SEC and hydraulically actuated. Elevator Each elevator has two hydraulic power sources and two actuators (one active and one in damping mode). ELAC 2 ELAC 1 SEC 2 SEC 1
Fraud
Horizontal Stabilizer Electrically controlled by one of three motors or mechanically controlled by the pitch trim wheels (through cable) and hydraulically powered by green or yellow hydraulic. After touchdown the stab trim is reset automatically to zero. Horizontal Stab. Priorities: ELAC 2 ELAC 1 SEC 2 SEC 1 (same as elevators)
37
22/05/12
Fraud
Green and Yellow hyd., 3 electric motors Rudder Rudder controls yaw. FAC 1 & 2 provide electric control through trim motors. Mechanically controlled and hydraulically actuated by rudder pedals if FACs fail.
Rudder deflection is normally limited according to airspeed (Rudder Travel Limit) but during dual FAC failure full rudder deflection is available when the slats extend.
38
22/05/12
Fraud
Rudder trim is automatic but can be done manually using electric RUD TRIM switch. A rudder trim RESET pb will reset the rudder to 0 trim (not available during autopilot operation).
ELACs sends signals to FACs and FACs compute yaw damper and turn coordinations. No feedback (rudder pedal movement) during yaw damper corrections or turn coordination. Roll Control provided by ailerons and spoilers. Electrically controlled by ELAC (ailerons) or SEC (spoilers) and hydraulically actuated.
Ailerons Each aileron is powered by Green and Blue hyd. and has two actuators (one active and the other damping). The ailerons droop 5 when the flaps are extended. If both ELACs fail then droop is deactivated and the ailerons streamline and only spoilers are used for roll control. 22/05/12 39
Fraud
Normal Law: for a given amount of sidestick deflection a given amount of G loading (pitch, elevators) or roll rate (roll, ailerons, spoilers) regardless of airspeed. Pitch is always kept in trim automatically. Flare mode gives slight pitch down after 50 for flare. Bank past 33 requires constant input or will automatically return to 33. Hard protections. 40 22/05/12
Fraud
Prot Alpha Protection, Angle of attack protection speed, top of amber tiger stripe A Angle of Attack instead of Load Factor (gs) S Speedbrakes retract A Autopilot disconnects P Pitch trim inhibited FAC think of a southern Dragnet, just the FACs yall Achieve electrical rudder control and characteristic speeds calculation for display on PFD. Y Yaw functions, normal and alternate yaw: Dampening, Turn coordination, Travel limit (F-CTL ECAM), Trim A Angle of Attack (flight envelope protection - speed tape) W Windshear - Reactive: 50 1300 Predictive is based on the Radar: [ 0 TO 100 kts, then 50 to 2300 // out to 5 nm] Low energy warning: - 2000 100RA Flaps 2, 3, F; and Normal Law Low Energy Warning is available in CONF 2, 3, or FULL, between 100 and 2,000 AGL when TOGA not selected. This will produce an aural SPEED, SPEED, SPEED when a change in flight path alone is insufficient to regain a positive flight path. Thrust must be increased. During deceleration, the Low Energy Warning is triggered before Alpha Floor.
41
22/05/12
Airbus A319, A320, A321 Notes Normal Law Protections (think of as A320 mode) Bank
Roll rate proportional to side stick deflection 67 Max (at 45 autopilot disconnect)
Fraud
Yaw
Turn Coordination & Yaw Dampening
Pitch
Load Factor proportional to stick deflection Max 30 nose up Max 15 nose down
Low Speed
Nonoverrideable AOA protection Prot
High Speed
Nonoverrideable nose up command prevents overspeed at Vmo/Mmo
Load
Clean/Flaps1 +2.5G/-1.0G Flaps Extended +2.0G/-0.0G
Floor Max
42
22/05/12
Fraud
Alternate Law Flight control will revert to alternate law after multiple failures of redundant systems. Amber Xs
Autotrim still available. Soft protections. No protection in roll, roll goes to direct. Pitch goes to direct for landing when landing gear extended (no flare mode). It is possible to be in Alternate law without speed Stability and/or Yaw Dampening. No TOGA Lock Alternate Law Protections (think of as 737-300 mode) Bank
Roll Direct No protections
Yaw
Yaw Dampening
Low Speed
Low speed stability Overrideable nose down command to
43
22/05/12
Fraud
Extended +2.0G/-0.0G
Direct Law Lowest level of flight control law. Proportional movement between sidestick deflection and flight control deflection. No autotrimming. No protections. Overspeed and Stall warnings available. The default mode on the ground in all cases (think about it, if you are on the ground you cannot have a G load or roll rate). This mode is most like a regular airplane (DC-9 mode). Amber USE MAN PITCH TRIM Occurs when: 3 IRS Fail or 2 RA Fail & L/G Down Alternate Law + L/G Down
44
22/05/12
Fraud
Abnormal Law This is entered by the aircraft being in an extreme unusual attitude (about double normal limits). When back to normal attitude aircraft is in Alternate Law except does not go to direct law on landing and no pitch protections. Computer reverts to Abnormal when it sees the aircraft in unusual attitude because computer logic says aircraft should not have been allowed by normal law protections into this attitude in the first place, therefore computer sees something is wrong. Mechanical Backup Pitch through horizontal stab trim, Lateral through rudders, Differential power. Both stab and rudder use cables going to controller and require hydraulic power. Bottom line here, very little manual reversion and if no hydraulic power you are a lawn dart. Red MAN PITCH TRIM ONLY
45
22/05/12
Airbus A319, A320, A321 Notes Occurs when: Loss of 5 Computers Loss of electrical Power Loss of Elevators Ailerons Spoilers Controls
Fraud
46
22/05/12
Fraud
Spoilers
Five spoilers are installed on each wing. Each spoiler is fitted with a single actuator supplied by one hydraulic source. Spoiler control is shared by the 3 SEC Computers. As a general rule, spoilers are automatically retracted when faulty, inhibited or not electrically controlled. From the wing root to wing tip they are numbered 1 through 5. All are used as ground spoilers. Numbers 2 through 5 (the 4 outboard spoilers) provide roll control. The middle three (2 4) provide in-flight speed brakes. If a SEC fails the spoiler(s) it controls is automatically retracted (if extended) and that spoiler(s) deactivated. There is no reversion to other computers.
Spoiler priorities: Spoilers 1 & 2 - SEC 3, Yellow and Green Spoilers 3 & 4 - SEC 1, Yellow and Blue Spoiler 5 - SEC 2, Green
47
22/05/12
Fraud
Speedbrake extension inhibited when (SAFE-T): S - SEC 1 & 3 fail A - Angle of Attack protection active ( Prot) or FLOOR active F - Flaps at FULL setting (also config 3: A321) E - Elevator (L or R) fails (spoilers 3 and 4 only) T - TOGA on thrust levers (OK, really above MCT but you better be in the TOGA detent if you are above MCT!) If speedbrakes out when inhibited they will automatically retract. Must restow speedbrake handle for 10 seconds to regain. Do not use speedbrakes below 1000 AFE. If one speedbrake on one wing fails the corresponding one on the other wing will be inhibited for symetry. Ground Spoilers are armed by raising the Speed Brake Lever. The speed brake lever does not move with auto extension. Ground Spoilers extend automatically: Partial Extension On landing Reverse selected on at least one engine with other at or near idle and only one main landing gear strut compressed Full Extension On landing or on takeoff above 72 kts. (rejected takeoff) Both thrust levers at idle (spoilers armed) or Reverse thrust selected on at least one engine with other at idle (spoilers not armed) and both mains compressed.
48
22/05/12
Fraud
Flaps
The flap handle has a trigger that must be squeezed to allow the flaps to move out of detent with balks at 1 and 3 to prevent overshoot. The flaps will only provide the configurations that are allowed for each detent, there is no in between the detents positioning. The flap handle controls both flaps and slats. Controlled by two Slat Flap Control Computers (SFCCs).
Both flaps and slats are powered by two hydraulic systems, flaps by green and yellow and slats by green and blue. If any hydraulic system fails leaving only one hydraulic system powering either slats or flaps the single powered control will extend and retract at half speed. If only one SFCC is functional the flaps and slats will operate at half speed. The flaps have 5 selected positions: 0, 1, 2, 3 and FULL.
Fraud
Note: when landing with Flaps 3 the LDG FLAP 3 pb on the GPWS overhead panel should be selected ON to prevent GPWS flap warnings when landing and also CONFIG 3 selected in PERF APPR for proper approach numbers. The flap position numbers are just that, position numbers, they do not correspond to degrees of flaps (or slats) and in fact each model (the A319, A320 and A321) has slightly different flap deflection schedules for certain flap lever positions. For example, Flaps FULL for the A319 is 40, A320 is 35 and the A321 is 25. The A321 also has additional slots built into the flaps to provide additional lift at slower speeds. Procedures remain the same for all models except for higher flap speeds on the A321. The flap indicator is in the E/WD and shows the amount of extension for both slats and flaps, with three positions for the slats and four positions for the flaps. Flaps 0 (zero) is flaps UP with all trailing and leading edge flap devices fully stowed. Flaps 1 is a hybrid with two separate configurations for the same Flaps 1 handle position. However, from a pilot standpoint the difference is transparent as the flap handle is treated the same. Flaps 1 position will provide flaps 1+F for takeoff and anytime you are retracting flaps from a higher setting (2, 3 or FULL). Any other time Flaps 1 will provide Flaps 1 (how about that?). OK, so what is the difference between Flaps 1 and Flaps 1+F? Glad you asked, simply this, the trailing edge flaps. The trailing edge flaps make up the +F as Flaps 1 is slats only in the initial position. During Flaps 1+F the slats and flaps will extend to initial positions.
50
22/05/12
Fraud
Now that I have you completely confused, here is the short story Flaps 1 on ground extending for takeoff Flaps 1+F (slats and flaps) Flaps 1 after takeoff during initial flap retraction from Flaps 2 or 3 Flaps 1+F (slats and flaps) Flaps 1 for landing extending from Flaps 0 Flaps 1 (slats only) Flaps 1 for Go Around retracting from 2, 3 or FULL Flaps 1+F (slats and flaps) As you can see the only time Flaps 1 gives you Flaps 1 (slats only) is on extension for landing, the rest of the time Flaps 1 is Flaps 1+F (slats and flaps). The E/WD will show either Flaps 1 or Flaps 1+F depending on configuration. Flaps 2, 3 and FULL all have both slats and flaps extended to some degree. Flaps have overspeed protection at flap setting 1+F so that at 210 KIAS the flaps will automatically retract to Flaps 1 (slats only). Please note on the A321 it is possible at high gross takeoff weights that F speed will exceed the flap speed for 1+F. In this case the flaps will automatically retract and the pilot will select flaps 0 at S speed which will retract the remaining slats.
Model A319/320
Position: VFE
1 230 KIAS
2 200 KIAS
3 185 KIAS
Slats have an alpha lock function that inhibits them from retracting from position 1 to 0 when at a high angle of attack or low airspeed.
51
22/05/12
Fraud
There are 4 Wingtip Brakes (WTB) that will lock the flaps or slats in case of asymmetry, overspeed, runaway or uncommanded movement. WTBs cannot be released in-flight. If flaps are locked out, slats can operate and visa versa. AMOR A -- Asymmetry M -- Movement uncommanded O -- Overspeed R -- Runaway
52
22/05/12
Fraud
Sidesticks
Perhaps one of the most distinctive and noticeable differences in the Airbus 320 series from other airliners is the sidestick. Most folks get comfortable with the sidestick within minutes. However, the computerized flight controls that the sidestick activate require some new features: No feedback (feel) is given. Sidestick is spring loaded to neutral. System algebraically sums the signals from both sticks if both are operated at the same time (dual input). However, the total input is no more than the max input from a single stick.
A red Takeover pb in the sidestick (also serving as autopilot disconnect) allows one pilot to override the other or to disable a damaged sidestick. If priority is taken an audio PRIORITY LEFT (or RIGHT) is sounded. A red arrow light will illuminate in front of the pilot who has been deactivated when one pilot has taken priority over the other. A green CAPT or F/O light will illuminate in front of the pilot with priority if the other sidestick is out of neutral. Last pilot to press Takeover pb has priority. Pressing Takeover pb for 40 secs. will latch the priority condition (pilot does not have to continue to press Takeover pb). However, a deactivated sidestick can be reactivated by momentarily pressing the Takeover pb on either sidestick. Green CAPT and F/O sidestick priority lights will flash during dual input and an audio DUAL INPUT will be sounded. The Takeover pb and dual input warning system are commonly misunderstood. A green light in front of you means dual input or you have just taken priority in a dual input situation and a red arrow means your sidestick has been deactivated. These are two different things. Dual input is almost always unintentional and unwanted. The takeover priority may be something that needs to be done if a sidestick has 53 22/05/12
Fraud
gone bad or some other problem has occurred. However, if YOUR sidestick is bad the OTHER pilot must latch it out with his Takeover pb. Sidestick locks in place when on autopilot. Pilot action on sidestick (or trim wheel) at any time will disconnect the autopilot.
O R
54
22/05/12
Fraud
Oxygen
Crew oxygen is supplied from one cylinder. A green over pressure disk is located on the outside of the aircraft skin below the Captains windows. Blowout of this green disk indicates thermal discharge. Crew oxygen is turned on using a pb in the overhead panel. Crew oxygen pressure is indicated on the SD and if low the pressure indication will have a half amber box around it. A chart is available on FCOM 3.01.35 to indicate amount needed for number of crewmembers. Masks are full-face and have clear tear-off strips. If face mask has surface contamination, the tear-off strip can be removed to clear an area to see through.
Passenger oxygen is chemically generated. Passenger oxygen is located at passenger seats, lavs, galleys and at each F/A station with 2, 3 or 4 masks to a group. Masks will automatically deploy when cabin altitude exceeds 14,000. May be manually deployed by pilot using red guarded MASK MAN ON pb. Oxygen generators last approximately 13 minutes after first mask in group is used. Passenger oxygen SYS ON light only means that the signal was sent, some masks may not deploy and F/As may have to manually open some doors.
55
22/05/12
Fraud
Powerplant
319:
320:
CFM 56-5B4/P rated at 27,000 lbs. thrust Compressor Turbine Low Pressure N1 3 stage 4 stage Hydraulic Pump Fuel Pump IDG FADEC Generator Starter LIMITS High Pressure N2 9 stage 1 stage
Accessory GearBox:
Max Starting Temp Max Continuous Temp TOGA Temp Max Oil Temp continuous Max Oil Temp Transient Min Oil Temp for starting Min Oil Temp for Take-Off N1 Max N2 Max
725 C 915 C 950 C (5 mins.) 140C 155C -40C -10C 104% 105%
Oil: 9.5 qts.+ 0,5qts / h Min for dispatch FADEC controlled (Full Authority Digital Engine Control) Each FADEC is a two channel computer (ECU) with one channel active and the other used as backup. Each FADEC has its own alternator that powers it once N2 is above 15%. If the alternator fails normal ships power will take over. 56 22/05/12
Fraud
Varies with demand, in flight with flaps at 0 Depends only on altitude, activated when flaps not at 0, allowing to accelerate rapidly from idle to go-around power Selected when on ground and thrust levers at idle, higher than forward idle.
Five Thrust Lever Detents: TOGA: FLX/MCT: CL: IDLE: FULL REV: Takeoff go-around Flex takeoff, Max continuous Climb thrust Idle thrust for forward and reverse Maximum reverse thrust
CONT IGN provided automatically (with Mode selector in NORM) when: Engine ANTI ICE on Engine flameout in-flight detected EIU fails Continuous ignition may be selected manually by positioning the ENG MODE selector to IGN/START
Fraud
Manual Start Sequence (Always with Check-list) ENG Mode selector to IGN/START ENG MAN START pb ON At Max Motoring (min. 20% N2) select ENG Master switch ON Fuel and ignition will begin when ENG Master selected ON At 50% start valve closes, ignition off At idle, about 58%, ENG MAN START pb OFF ENG mode selector to NORM N2 background grays out during start, returns to normal when stabilized at idle Ignition A or B will show on SD during normal start, A & B during manual start Note: Run engines at or near idle for 2 mins. and run engine for 5 mins. before applying takeoff thrust, run engines at least 3 mins. after landing.
58
22/05/12
APU
APU can supply electrical up to 39,000 and supply full electrical load up to 25,000 and bleed air up to 20,000. Electrical takes precedence over bleed air. APU bleed is NOT permitted for Wing anti-ice. Electronic Control Box (ECB) controls and monitor: APU Start sequence Speed & Temp Bleed Air Normal shutdown sequence Automatic shutdown The APU is fed fuel from left fuel manifold. If no other fuel boost is available, the APU will activate a separate dedicated APU fuel pump. In flight (above 100 kts.) on Bat only the APU will not start (RAT failed). With RAT (loss of GEN 1 & 2) the APU is allowed 3 minutes for a start attempt. The APU can supply the entire electrical system on the ground. In the air the APU will not supply the main galley shed busses. The APU will auto shutdown and fire the extinguisher bottle on the ground but not in-flight. In-flight the APU must be manually shut down and extinguished for fire. If the APU SHUT OFF pushbutton on the external panel or the APU FIRE pb on the overhead FIRE panel is pressed the APU will shutdown but the extinguisher will not automatically fire. Note: APU will auto shutdown in-flight for reasons other than fire. The APU generator will automatically come online if engine gens. or external is not already online. The APU is ready for bleed and electrics when reaching 95% for two seconds or 99.5%. The AVAIL light will show in the APU start pb and green APU AVAIL will show on EWD display when APU gen is available for use. APU bleed may be selected on whenever needed and APU will allow bleed to come online after allowing time for EGT to stabilize. On shutdown the APU Master is pushed off. The APU will continue to run for cooling period before shutting down. If the APU Master is pressed back on before the APU shuts down the APU will continue to run. When shutting the APU down for the Parking & Securing checklist wait 2 mins. after APU Avail light goes out before switching batteries off. If APU is left running, leave batteries on for fire protection. Note: APU Bleed Air extraction for wing Anti-ice is NOT PERMITTED APU Bleed is actually supplied by APU load compressor. The Line method for starting the APU and putting it online: Press APU Master Switch pb ON Wait about 3 seconds then press APU Start pb ON Press APU Bleed pb ON 3 Start cycles 1 min cooling between 60 minutes cooling after
Fraud
APU Temp Limitations: Maxi operating: 725C Maxi starting 1038C APU LOW OIL LEVEL Normal operation allowed for a further 60 hours. Thats it! If EXT PWR is not already established online the APU GEN will automatically come online followed by APU bleed air after the proper interval which will automatically turn on the packs assuming their pbs are in the normal on (switch blank) position. Isnt technology wonderful! You can start the APU before your walk around and the APU will be heating the cabin and have air pressure available for the coffee maker by the time you get back! ECAM APU Page: APU Bleed Air Pressure: - Amber XX PSI when ADIRS 2 is not available or selected OFF
60
22/05/12
Fraud
Equipment
Potable water
61
22/05/12
Instruments
ECAM
The ECAM (Electronic Centralized Aircraft Monitoring) system is made up of two primary components, two SDACs (System Data Acquisition Concentrators) and two FWCs (Flight Warning Computers). A loss of only one SDAC or only one FWC will not result in any loss of function. The second computer can handle all functions alone. The SDACs receive data from sensors and will send signals to 3 DMCs (Display Management Computer) which generate the screen image. The SDACs also send signals to the FWC. The FWC will generate various warning/caution messages.
Fraud
The E/WD (Engine/Warning Display) is the display that shows normal engine readings and ECAM messages. The SD (System Display) is directly below the E/WD and normally shows system pages or status. For information on switching screens in case of failures see EFIS later in this section.
ECAM uses color to indicate the importance of the indication RED: Immediate action required ORANGE (AMBER): Awareness but no action required GREEN: Normal operation WHITE: Titles and remarks BLUE (CYAN): Actions to be carried out or limitations PURPLE (MAGENTA): Special messages (i.e. inhibition messages) Note: pulsing green or amber indications are approaching limits If a FWC fails the Master Caution and Master Warning lights will indicate the failure (along with a warning from ECAM) by the upper or lower light in both the Master Caution and Warning light being out. If the #1 FWC fails then the captains 22/05/12 63
Fraud
upper lights would be out and the F/Os lower lights would be out. If #2 FWC fails the reverse lights will go out. Loss of both FWCs will result in a loss of most warning capability. The dual failure of the FWCs will result in an amber caution with no aural. ECAM system pages are controlled through the ECAM control panel. Captains will be using the mnemonic departure.
FHED
F H E D
FUEL, balance, configuration, quantity HYD, Hydraulics quantity (pointers in boxes) ENG, Engine oil quantity (min. 12.5 qts.)
DOOR/OXY, Doors armed, O2 pressure (note: overwing slides always armed) Note: Press FUEL, HYD, ENG and then press ENG again to return to default DOOR/OXY page.
64
22/05/12
Fraud
ECAM Procedures Upper ECAM (E/WD) Primary Failures Secondary Failures underlined starred ECAM Actions Affected Systems ELEC DC BUS 1 FAULT *ELEC Lower ECAM (SD) Procedures Inop Systems Status Status
Work in a Z fashion from upper left, upper right, lower left, lower right. When an ECAM warning occurs the first pilot noting it should read the title. Appropriate systems page will be shown on lower ECAM (SD) to help identify problem area(s). Please note that the top displayed underlined system will control the lower SD display. Then the PF should call ECAM Action. The PNF should read the full line of action items. Confirm all major actions before continuing to next, such as thrust lever movement, engine master switch, engine fire pb selection or IDG disconnect and have the PF guard good control. Repeat response as you complete action. As you complete the items listed in cyan (blue) (think Blue to Do) they will be automatically cleared from the screen. Continue until you reach the next underlined item. Read through any boxed item (note: boxed items indicate failure of a primary system that will cause the loss of another system or systems on the aircraft which will be listed as secondary or *starred systems). When reaching the next underlined title or the end of the procedure then proceed with clearing ECAM. Be sure to do ALL applicable blue action items between underlined titles before proceeding. If there are too many steps to all be on the screen ECAM will put a green down arrow to indicate that there is screen overflow. As you complete the items and they are cleared the overflow items will automatically scroll up onto the screen. If there are too many items that cant be cleared then press the CLEAR pb for the next page. Note: you may not be able to clear all blue items. In some cases ECAM will not have a way to know that you have done an item, such as contact ATC. Some may not apply such as during Engine Failure ECAM will give a choice of damage or no damage procedures. When all action items are finished for an underlined item and you are at the end or the next underlined item the PNF asks, Clear ECAM? PF will reply, Clear ECAM if ready to continue. Be sure that no further cyan messages remain for any underlined item that can be eliminated before clearing. Some blue action items the computer cannot get feedback from, and these will remain on the screen. 65 22/05/12
Fraud
ALWAYS CONFIRM AN ECAM CLEAR. The SD will automatically display the affected underlined system if there are additional failures. If the problem stops while doing action items some action items may clear or change automatically. For example, if an engine fire goes out while running ECAM you will see the ECAM ENGINE FIRE go away, the red FIRE pb on the FIRE panel and the red FIRE light on the engine panel will go out and the LAND ASAP will change from red to orange. When ECAM is cleared the next procedure will appear (additional primary failures are listed in the stack on the right) or if all procedures are done then ECAM will automatically present the first page of the affected systems on the SD. Affected systems (secondary failures) are listed in amber on the top right of the screen with an *asterisk in front of them (*F/CTL). After reviewing the screen you will clear it and the next system screen will be shown. After each screen you should ask and confirm ready to clear the screen. Continue until all amber is cleared and only green memo messages are left. Example: PNF will then review all affected equipment shown in amber on Flight Control side. When done PNF will ask, Clear Flight Control? PF will reply, Clear Flight Control if ready to continue. When all the affected system screens have been cleared the status page will come up automatically. If Status or Inop Systems takes up more than one page on ECAM there will be a green down arrow to indicate to scroll to the next page. In this case you will clear ECAM to scroll to the rest of the procedure. After using clear to see additional Status or INOP Systems pages you can press the STS key to see the first Status or INOP Systems page again. Status page will contain items such as procedures, limits, etc. PNF will then read all status items line by line. When done the PNF will ask Clear Status? The PF will reply, Clear Status if ready to finish. If PF needs to stop ECAM say Hold ECAM, when ready to continue say Continue ECAM. Pilot verbiage during ECAM is Challenge, Response, Response. For example: PNF: Green Engine 1 Pump, OFF, (push off Green Engine 1 pb) OFF When operating controls that must be confirmed (thrust lever movement, engine master switch, engine fire pb selection or IDG disconnect) the PNF must allow the PF to confirm the action and guard the good controls. Verbiage in this case will be like this: PNF: Thrust lever 1, Idle, (PF will guard thrust lever 2 with hand) PF: Confirmed (PNF will bring thrust lever 1 to idle), PNF: Idle A red LAND ASAP suggests landing at nearest suitable airport (more severe). 22/05/12 66
Fraud
An amber LAND ASAP suggests the pilot should consider the seriousness of the situation and suitability of the airport before landing (less severe). Landing Distance Procedure If the procedure directs you to do the landing distance procedure (LDG DIST PROC) then you will look in the QRH under Miscellaneous for: Landing Configuration, Approach Speed, and Landing Distance Corrections for Failures (for the model aircraft). Current QRH pages are
Find the appropriate equipment failure(s) in the table and note the actual flap lever position for landing. Please note that the actual flap and/or slat positions may not match the flap lever position depending on what procedures you are accomplishing. Note any speed increment to be added. Finally note any landing distance multiplier. If there are multiple failures and you need to apply more than one equipment failure you may need to adjust your multiplier. If the multipliers all have asterisks just take the highest multiplier. If any of the multipliers dont have asterisks then multiply the multipliers together and use the resulting number as the total multiplier. Instructions are shown on QRH 2.33. Find the performance section QRH 4.03 and find the LANDING DISTANCE WITHOUT AUTOBRAKE CONFIGURATION FULL table. ALWAYS use the Config Full table, even if landing with less for the procedure. Find the applicable distance. Apply any needed corrections. Please note that this is a reference distance only, if you have autobrake available you should use it! Use the multiplier from the earlier table and multiply it by the corrected reference distance and this will be the minimum distance runway needed for this procedure. Finally, take the speed increment from above and add it to VLS and add any wind correction (see QRH 2.32 for tables) and put the resulting VAPP in the MCDU PERF APPR page under the LSK 5L. When using speed increments ALWAYS USE SPEED SELECT on approach. Do not use managed speed when speed increments have been applied. Use the VAPP set in the PERF APPR to remind you what speed to select when on approach. If time permits FCOM 3.02 expanded procedures will assist in finding the distance multipliers and speed increments. Note: If ECAM directs to recycle Flaps/Slats speed select below 200 kts. and select flaps 2 ECAM action should not be taken (except to cancel audio warning through the MASTER WARN light) until: The flight path is stabilized and The aircraft is higher than 1,000 AFE CAUTION: There are times that ECAM may direct the pilot to do a procedure that is not what you should do. Examples are if an ECAM directs to turn off the last available source of hydraulic power (no power to flight controls is a bad thing in 67 22/05/12
Fraud
any circumstance) or opening the fuel X-feed for fuel imbalance when in fact you have a major fuel leak. As always Captain, it is your aircraft and you have the final decision. Exercise your emergency authority as needed (but always with discretion!).
F H F E A
68
22/05/12
Fraud
EFIS
A white diagonal line across the display means that the DMC (Display Management Computer) has failed. The CRT itself is still working. Just switch to the standby DMC on the switching panel to restore the displays as normal.
A failure of the DU Display Unit (display blank) means that you will have to swap screens to view all information. The PFD has priority over the ND and the EW/D has priority over the SD. This means that if the PFD display fails then the PFD will automatically display on the ND display screen. However, if the ND fails the PFD will remain on its normal screen. If you wish to view the ND you can press the PFD/ND XFR switch. In the same way the EW/D has priority over the SD. If the SD needs to be displayed use the ECAM/ND XFR switch on the switching panel to bring that screen up on the CAPT or F/O ND as selected. A failure of both the ECAM screens (EW/D and SD) will require use of the ECAM/ND XFR switch on the switching panel to view the EW/D screen on the ND display and by pressing the required system pb on the ECAM Control Panel you can view the SD info on the ND as needed.
69
22/05/12
Fraud
The ND has two brightness controls, outer and inner bezel control knobs. The outer ND bezel controls brightness of the radar and terrain on the ND. The inner knob controls the brightness of all the other normal ND display symbols. Note that if the PFD/ND XFR button is used the outer bezel is disabled and only the inner knob is available for brightness control. STS in a white box will show on the bottom of the EW/D if there are any systems downgraded to remind the crew of any status information. If there is a system advisory message when the SD has failed the EW/D will flash a white ADV at the bottom of the screen to notify the crew to select the SD for viewing. The current airspeed is indicated by a fixed yellow reference line. A yellow speed trend arrow will appear from the speed reference line to indicate the anticipated airspeed in 10 seconds. Green Dot is a (gasp!) green dot on the speed scale and is available only when aircraft is clean (flaps 0). It shows best lift over drag speed (L/D) and is also called VFTO (Final Takeoff speed). Green dot is used during normal takeoff and the engine-out maneuver and gives best angle of climb speed. On the altitude scale the Landing Elevation is a blue line and is based on barometric information. The Landing Elevation is available only in QNH (below 18,000) and on approach. Ground Reference display on the altitude scale is a red ribbon and is based on radar altimeter information. Radar altimeter readout comes on screen in green below 2500 AGL and goes amber (if DH is entered) when 100 above DH (CAT II/III). If an MDA has been entered the altitude (note: this is the normal altitude readout, not the radar altimeter readout) will turn amber below the MDA (CAT I / RNAV). Magenta means managed and Blue means selected For example if the commanded speed is by pilot action (speed select) the speed target index (speed pointer) will be blue. If the commanded speed is controlled by the FMGC (speed engage) the speed pointer will be magenta. When a new altitude is selected the new target altitude will appear above (during climb) or below (during descent) the altitude scale. The new target altitude will move onto the scale once it is within the altitude scale range (about 600).
Takeoff Warning
Slats/Flaps Pitch Trim Speed Brakes Sidestick Fault Hot Brakes Door Not Closed
the following are only triggered when takeoff power is set Parking Brake On Flex Temp Not Set (not displayed if thrust levers set in TOGA detent) 70 22/05/12
Fraud
Altitude Alert
Altitude alert (tone and pulsing yellow altitude windows) is inhibited when: Slats are out and landing gear selected down Landing gear locked down Captured on glide slope The tone is also inhibited when on autopilot and capturing a normal set target altitude, but pulsing yellow window is still effective.
71
22/05/12
Navigation systems
GNADIRS
The Global Navigation Air Data Inertial Reference System (say that five times fast!) provides the FMGS with the data input it needs to navigate the aircraft. The FMGC decides which signals are most accurate and provide a synthetic (best guess) aircraft position after weighing all available data. The FMGC can also estimate the accuracy of its synthetic position due to available sensors and data. This information will be used during RNAV approaches. The IRUs have laser ring gyros that provide a stable reference signal as well as provide attitude information. Be very careful NOT to just turn off the IRU because it gives a bad nav signal. It may still be giving good attitude information and can be selected to attitude information only (ATT). The FMGC can track IR drift and predict aircraft position even when GPS or ground based (VOR/DME) signals are lost.
Fraud
GNADIRS also provides the aircraft with needed air data information such as altitude, mach, temperatures, airspeed, etc. Failure of an associated air data reference DOES NOT fail the IR! The failed ADR can be turned off by deselecting its pb and still maintain all IR and GPS functions. There are two independent GPS receivers called MMRs (Multi Mode Receiver). The MMRs process position data and send it to the GNADIRUs. MMR1 sends data to ADIRU1 and MMR2 sends data to ADIRU2. Both MMRs can send data to ADIRU 3 as needed for backup purposes if ADIRU 1 or 2 fail. The system is very accurate and reliable with a high degree of redundancy using three ADIRU units and multiple navigation signal inputs from GPS and IR. The FMGC also takes VOR/DME signals into account along with the GNADIRS data to compute aircraft position. The third GNADIR is basically a standby that can be selected if #1 or #2 fail. Amber FAULT light: Steady, IR lost Flashing, may be available in ATT only, NAV lost 73
22/05/12
Fraud
White ALIGN light: Steady, in align mode (normal) Flashing align fault No entry in 10 mins. 1 difference in lat. & long. from shutdown position Extinguished, alignment is complete (normal) Note: DO NOT move aircraft during alignment. Wait 3 minutes after aircraft stop to re-align or turn of.
74
22/05/12
Fraud
75
22/05/12
Fraud
EGPWS
Enhanced GPWS provides all normal aural GPWS functions as well as the enhanced terrain avoidance features. The enhanced function is database (computer) driven but it is shown in a radar format. Please note that the radar is NOT being used for terrain detection but the DISPLAY will override the weather radar image display when the terrain on ND pb (TERR ON ND) is selected. If the TERR ON ND pb is not selected and a warning is generated the terrain display will come on automatically and override weather radar display. The Terrain sweep is a distinctive middle to the sides to make it obviously different from the normal radar. The enhanced terrain feature can be shut off using the TERR pb on the overhead without losing any of the normal GPWS functions. TOGA thrust Autopilot off Roll wings level Sidestick FULL AFT until at safe altitude The PNF should call altitude from radio altimeter and climb/descent trend: 300 descending, 200 descending, 400 climbing. PNF call out safe altitude MSA is 6,500 ft. Dont change gear/flap configuration until safe (ensure Speedbrake stowed).
76
22/05/12
Fraud
77
22/05/12
Fraud
TCAS
RA Manuver If a traffic resolution is given (CLIMB, DESCEND, MAINTAIN VERTICAL SPEED MAINTAIN, ADJUST VERTICAL SPEED ADJUST): Autopilot OFF Both Flight Directors OFF Adjust vertical speed as required to remain in green area of vertical speed scale (stay outside of red). Avoid excessive maneuvers, if needed use full speed range from Vmax to max. Go Around must be performed if RA CLIMB or INCREASE CLIMB is given on final approach.
78
22/05/12
Fraud
When using the RMP or ACP you must realize that every control is independent. For example you can tune on VHF 2 while listening on VHF 1 while transmitting on VHF 3. On the RMP a green triangle light will indicate which radio is being tuned and on the ACP a triple bar green light will indicate which radio is set to transmit. On the RMP only one radio may be tuned at a time, selecting VHF 1 for tuning will deselect the prior selection. The ACP transmit is the same way, only one radio may be selected for transmit from that ACP at one time. On the ACP the pilot will select up or out the radios or interphones to listen to. You may select as many as you wish and set independent volume control on each. Please note that you must select out a radio to listen to even if you have pressed to tune or talk on it, the audio is NOT automatically selected when you use the RMP. Comms are monitored by ECAM for stuck mike. All RMPs will tune any radio. ACPs may be switched in case of failure using Audio Switching panel on overhead. Note: ACARS is set on RMP 3 (standby on overhead) and VHF 3 cannot be set to use any other radio.
80
22/05/12
Fraud
Cabin
Emergency Evacuation
81
22/05/12
This level is basically the same as any other aircraft you have flown with autopilot and autothrust. The autopilot and autothrust are controlling through the same flight control system that the pilot uses when hand flying. The final and most sophisticated level is computer guided. In this case the pilot enters the desired settings in the FMGC and the computer calculates the proper flight path and track. The FMGC then commands the autopilot and autothrust to properly maintain the computed track and path.
Fraud
If the pilot wishes to make changes or revisions to the flight plan then it is done to the FMGC which then recalculates the needed information. For example, if the pilot wishes to change the flight plan route to go direct to a new fix, the new fix is typed into the MCDU and entered into the DIR page. The FMGC now computes the new course and commands the autopilot to turn to the new heading. Computer Guided Pilot FMGC Autopilot Flight Controls Autothrust Thrust
Each higher level uses all the previous levels. In other words computer guided flight is also using the autoflight and manual levels. The pilot can always drop down from one level to a lower level by disengaging the appropriate equipment. For example, the pilot may be climbing under computer control in Managed Climb. By selecting a vertical speed of 1500 fpm on the FCU the pilot has now put the vertical path in autopilot control. The FMGC is not controlling the climb rate. If the pilot then disengages the autopilot the aircraft is now under manual control and the pilot is now manually controlling the climb rate. Two things that should be pointed out: You can have various levels of control at one time. For example, the track may be computer guided by the FMGC while the vertical path is under autopilot control. Another example is when the pilot is hand flying but using autothrust (which is very common). In this case the flight controls are in manual but the thrust is in autoflight. The other thing to point out is that when hand flying the pilot may use the Flight Director so that while the aircraft is under manual control the pilot is still getting autoflight or computer guided assistance.
83
22/05/12
Fraud
FMGC
Three different operational modes when degrading: DUAL All is OK! You have two, like many other things! The two FMGC each perform their own computations and exchange data on a crosstalk bus. Data entered into either MCDU is transferred to both FMGCs. INDEPENDENT Mismatch in Data base or in FMGC Program between the two FMGC. Entry on one MCDU is transmitted only into respective FMGC. SINGLE 1 FMGC INOP The remaining FMGC control all peripherals.
84
22/05/12
Fraud
Autopilot
There are two autopilots installed. Normally you will only use one autopilot at a time (Capt. using A/P 1 and F/O using A/P 2). However, for every ILS approach you will engage both autopilots (except, of course, when the second is inop.). The autopilot can be controlled either directly from the FCU (Flight Control Unit) or through the MCDU and the FMGC. In both cases you must monitor engagement status on the FMA. The FCU has four places to make inputs, Speed, Heading/NAV, Altitude and Altitude Hold/Vertical Speed. In each case the knob for the selection can be pressed or pulled. Pressing the knob will tell the autopilot to use the FMGC for guidance. Pulling the knob will tell the autopilot to use a pilot selected value. 22/05/12 85
Fraud
When the autopilot is engaged (push) on the FMGC for a setting a white dot will appear on the LCD readout for that setting. If the autopilot is selected (pull) to a pilot set value the pilot value will appear in the LCD readout. Always confirm settings on the FMA at the top of the PFD. Speed: Pull to select to KIAS or Mach by pilot, dial to needed speed. Press to engage in speed mode in FMGC Heading: Pilot can dial to set desired heading then pull to select HDG mode. Pressing HDG knob will engage NAV and allow autopilot to track FMGC route. Altitude: Value set by pilot, pulling will allow open climb/descent (full power climb, idle descent), pressing will engage to allow managed climb/descent on FMGC Altitude Hold/Vertical Speed: Pressing knob will engage an immediate level off. Pulling knob will select vertical speed mode. Dial knob to select amount of climb or descent in hundreds of feet per minute.
Make
your flight instructor happy!: Use Noun/Verb when commanding changes on the FCU (Flight Control Unit) Example: Speed Select 170 pilot selects new speed of 170 Speed Manage speed controlled by FMGC, known as managed speed. Heading Select selects heading to previously dialed or current heading Heading Select 280 pilot selects new heading of 280. Nav Manage track controlled by FMGC route Autopilot Off or Autopilot 1 (2) Flight Directors Off or Flight Directors On Speed Select or Speed Manage Heading Select or Nav Manage Open Climb (Descent) Select or Climb (Descent) Engage Vertical Speed Plus (Minus) or Altitude Hold
Autopilot Flight Directors Speed Heading/Nav Open/Managed Climb (Descent) Vertical Speed
Select is always knob pulled to you (pilot is taking the control of the autopilot). When using select if you are changing the amount from what is in the window then say amount after saying select. 86 22/05/12
Fraud
Manage (Hold) is always knob pushed away from you (pilot is giving control of autopilot to the plane by FMGC). Memory and Non-memory autopilot limits After Takeoff (if SRS indicated) Enroute Non-precision approach* Circling CAT 1 ILS Approach (no autoland) CAT II ILS Approach Autoland After a manual go-around 100 AGL 500 AGL MDA MDA 100ft 40 below DA 160 mini 80 Touchdown 100 AGL
*Autopilot
will disconnect at MDA-50 if MDA has been entered in MCDU APP Page. If not it will disconnect at 400 AGL Autothrust The big picture on Airbus is autothrust; During ground operations handle the thrust levers as on a normal aircraft. At takeoff push the thrust levers up to 50% on N1 until both engines stabilize (position is at the H of A/THR), then push the thrust levers up to FLX/MCT (two clicks) or TOGA (three clicks). When LVR CLB flashes (normally about 1000) on the FMA reduce the thrust lever back to CL (one or two clicks). The thrust will now be controlled through the FMGC or the FCU. The thrust levers in normal operation will not move again until landing when at about 30 to 50 the PF will reduce the thrust lever to idle and the autothrust will automatically disconnect at that point. There is no physical connection between the thrust levers and the powerplant. It is all done electronically which is called FADEC (Full Authority Digital Engine Control). Thrust is now set by selecting Open Climb (OP CLB) or Open Descent (OP DES) or Managed climb or descent. Managed climb or descent means that the FMGC is controlling in either. Open mode simply means using either full climb thrust for climb or idle thrust for descent. Autothrust controls to a limit in Open, either the climb limit or the idle limit. The other FCU method to control thrust is to set vertical speed (V/S) which allows the thrust to maintain speed and climb rate is controlled through pitch. In this case autothrust is maintaining speed and is in Speed mode. Of course, during cruise and approach the altitude or glide slope is held through pitch with the autothrust maintaining the required speed. Managed thrust is controlled by the FMGC. If you dont get anything else out of this little discussion please understand that the autothrust works in one of two modes, Open (controlling thrust) and Speed (controlling speed). Further, Open mode can be either climb or idle thrust.
87
22/05/12
Fraud
Most of the time if you are going to have a problem it is in the Open mode (controlling to thrust). If you are having problems with thrust doing something other than what you think it should you can possibly try: Turn off flight directors (if hand flying), this will cause autothrust to go to Speed mode Select vertical speed (if in Open climb or descent), this will cause autothrust to go to Speed mode Select Speed Select (if in Managed speed), this will force the commanded speed to what you desire.
Activate A/THR:
Note: on ground you will set takeoff thrust to either FLX/MCT or TOGA which are manual thrust settings. When coming back to the CL detent after takeoff you are putting the thrust levers to the A/THR active range, thus activating autothrust. A/THR pb pressed on when autothrust in active range Set thrust levers to active range when A/THR pb armed ALPHA FLOOR protection activated (not a great way to activate!)
Disconnect A/THR:
Press instinctive disconnect pb on thrust levers Place both levers to idle detent Press off the A/THR pb on FCU when system active (green light goes out) Set one thrust lever beyond MCT or both beyond CL detent when RA is below 100
88
22/05/12
Fraud
THRUST LOCK
The Thrust Lock function prevents thrust variations when the Autothrust System fails and disengages. How should the crew suppress the thrust lock condition? Moving the Thrust Levers out of the CL or MCT detent suppresses the Thrust Lock and allows manual control by means of the Thrust Levers. The Thrust Lock function is activated when the Thrust Levers are in the CL Detent (MCT Detent when Single Engine) and: The pilot disengages A/THR by pushing the A/THR pb on the FCU, or The A/THR disconnects due to a failure The Thrust is locked or frozen at its level prior to disconnection. When Thrust Lock is active: THR LK flashes amber on the FMA ECAM ENG THRUST LOCKED flashes every 5 seconds ECAM displays THR LEVERS MOVE A Single Chime sounds and the MASTER CAUTION Light flashes every 5 seconds. All Warnings cease when the Thrust Levers are moved out of the Detent. Note: Pulling back the thrust levers from the CL detent during autothrust operation will allow the pilot to limit autothrust upper limit but autothrust is still active until levers are at idle. Chime and ECAM warning will sound every 5 seconds to remind pilot to either disconnect autothrust or reset thrust levers to CL detent. The proper way to disconnect autothrust and begin manual thrust operation is to bring thrust levers back until the TLA donuts are matched to thrust indicators and then press instinctive disconnect pb on thrust lever.
Airbus Gotcha: Warning: If autothrust is disconnected and then thrust levers Airbus Gotcha: Warning: If autothrust is disconnected by pressing the
are pulled back from CL detent the thrust will immediately go the power selection commanded by the thrust levers and indicated on the TLA donuts. Be sure power is at the intended setting when A/THR is disconnected to avoid power surge. A/THR pb on the FCU the aircraft wont know if the pb was pressed off or signal was lost and will give an ECAM warning to move thrust lever. It will think you are in a Thrust Lock situation. Bottom line here, just use the instinctive disconnects (or idle when at flare) to disconnect the auto thrust. Alpha Floor Angle of attack between Prot and Max at which the autothrust will command TOGA regardless of thrust lever position. Alpha Floor will give: A FLOOR in green with flashing amber box on FMA and in amber on E/WD TOGA LK in green with a flashing amber box around it on the FMA when the A FLOOR condition is left. TOGA thrust is frozen. To cancel ALPHA FLOOR or TOGA LK disconnect the autothrust. 89 22/05/12
Fraud
ALPHA FLOOR is available in NORMAL law only. ALPHA FLOOR is enabled at liftoff and active during flight, disabled at 100 RA on approach to let you land the aircraft. ALPHA FLOOR is disabled if you press the instinctive disconnects for 15 secs. Please note that Alpha Floor is a fonction of the autothrust while Alpha Prot and Alpha Max are actually to do with flight controls. THR LK Thrust Lock occurs if the autothrust system fails. THR LK flashes on the FMA and ECAM memo displays AUTO FLT A/THR OFF. The thrust will be frozen at the last commanded setting until the pilot moves the thrust levers, then thrust will follow the movement of the thrust levers and be controlled manually.
Make your flight instructor happy!: The following is in bold print because it will make your life easier. Always match the TLA to the thrust before disconnecting (using instinctive disconnect pb), no matter what kind of thrust situation you are in. This works in normal autothrust, THRUST LOCK and TOGA LOCK. Although not always technically necessary, by matching TLA to thrust you always avoid any unintentional thrust excursions and use good practice. Think Match and Mash. During every approach you will need to confirm autothrust is in SPEED mode on FMA or off by 1000
90
22/05/12
Airbus A319, A320, A321 Notes Missing Link or AP/FD & A/THR interaction
Fraud
Well, OK, it isnt that missing link but there is a link between the autopilot and/or flight director and the autothrust. The A/THR and the AP/FD work together to maintain speed and trajectory (altitude, glide slope, vertical speed). If one is maintaining speed the other will maintain trajectory and visa versa. If you think about it you are used to doing this yourself when flying manually. On climb you set climb power and maintain speed with pitch but when leveling for cruise at altitude you use pitch to maintain altitude and power to hold speed. The Flight Guidance acts in the exact same way. There are two basic ways the autoflight maintains control. AP or FD in trajectory mode (example: altitude hold, V/S, G/S) Or AP or FD in SPD/MACH (AP or FD adjust pitch to hold speed) A/THR in THR mode Steady thrust set to either THR CLB (OPEN CLB) or THR IDLE (OPEN DES) A/THR in SPEED mode maintain speed or MACH in cruise and approach
There are times that the autoflight cannot hold what has been set and will have to change modes. This is called mode reversion when the modes change automatically without the pilot calling for it. This is both a part of normal flying and also part of the system to prevent flight outside the envelope. An everyday example is during a climb the autopilot normally will control pitch to keep speed in OPEN CLB and the autothrust will maintain climb thrust (THR CLB). On approaching level off at the target altitude pitch will now revert from speed to vertical speed and thrust will revert from climb thrust to speed. This will be true even if the pilot reselects a new altitude before the level off is complete. The vertical speed mode will remain until the pilot reselects something else. Basically, be aware that if the autopilot is controlling pitch then the autothrust is controlling speed and visa versa. Only one controls pitch or speed at a time, never both controlling the same thing together. A common reversion mode is if the aircraft is climbing in Open Climb or Managed Climb and the pilot is suddenly given a new altitude. The new altitude is below the current altitude. The mode will revert to V/S set to the current vertical speed upon reversion. The pilot can then change the vertical speed to a descent or select Open Descent. Reversions can also happen when hand flying if you dont follow the flight director. If in Open climb or descent and you allow the speed to hit max or min the autothrust will go to SPEED mode and attempt to regain the selected speed while the flight director bars will be removed! Turn OFF FD when hand flying!
91
22/05/12
Fraud
You are hand flying with the flight director on (bad thing!). You are getting ready to level off just prior to the Final Approach Fix on an approach. However, you are not quite level at the set altitude and the FMA does not yet show ALT* for capture. You are slowly leveling off just a little high without realizing it and as you have been in Open descent the thrust remains in the commanded idle. Speed decays to below VLS. Suddenly climb thrust is commanded even though you are now wanting to continue descent. Sounds like a flyby to me!
92
22/05/12
Fraud
FMA Flight Mode Annunciator The FMA allows the pilot to know what modes the autoflight systems are in and what can be expected. There are times when changes will occur in the modes without pilot action. This mode reversion cannot be tracked on the FCU, you must look at the FMA to know what is actually happening. The FMA is broken into columns as shown below:
COLUMN NAMES
THRUST VERTICAL LATERAL APPROACH CAPABILITY STATUS AUTOFLIGHT ENGAGEMENT STATUS
Each column has rows for messages and memos. There are up to three rows available for each column to use. The first three columns, Thrust, Vertical and Lateral have the following rules: Top row: Green Active or Engaged, White - Armed Middle row: Blue or Magenta Armed (Magenta shows ALT CSTR from FMGC) Bottom row: Messages about flight control first priority Bottom row: Messages about FMGS have second priority
COLUMNS ROWS
ACTIVE, ENGAGED MODES ARMED MODES MEMOS, SPECIAL MESSAGES THR MAN THR LVR ASYM VERT ALT* G/S LAT APP STAT CAT 3 DUAL DH 100 ENGAG STAT AP 1+2 1FD2 A/THR
NAV
LOC
This is what the FMA looks like at the top of the PFD:
The FMA is at the top of the PFD and allows the pilots to see exactly what the various modes of the auto flight system are. The above examples are just given to allow you to see what type of messages would be in the FMA, not an actual flight situation. A starred message (ALT*) means that portion is in the process of capturing. A white box message means mode change or automatic switching has just taken place in past 10 seconds.
93
22/05/12
Fraud
FMS A little general theory: All FMS systems that I have used function or think in a Mode pattern. This is to say that the FMS must always be in a mode or phase and be aware of what the aircraft is doing to know what mode it should be in. The FMS will have many different ways to identify a mode change but it will need to change modes during every flight. The pilot should be aware of the modes and their changes. The Airbus is no different. For vertical planning the FMGC has modes called Flight Phases that are named Preflight, Takeoff, Climb, Cruise, Descent, Approach, Go Around and Done. In addition the FMS needs to know when the aircraft is in taxi, engine-out and landing modes. With the pilot entering the proper needed data during initialization the FMS is able to properly plan and control a flight through all the necessary phases or modes. Further, the pilot must enter a route of flight to allow for lateral planning. This will also involve modes, in this case, takeoff runway, SID (if applicable), enroute, STAR (if applicable) and approach/go around and landing runway. The pilot will enter the needed route data before flight and modify it in-flight as necessary. Some changes the pilot will make are considered Strategic (entire flight) and some are Tactical (current flight phase or mode). As you learn the different functions of the FMGC and the Autoflight system be aware of whether a function is Strategic or Tactical. If a page is longer than one screen can show you will use the scroll or slew keys (up/down arrow keys, to show additional information. If there is more than one ) page to a key you can press the NEXT PAGE key to see the succeeding pages. Sometimes additional information can be accessed from a page and you will see an on screen prompt ( <, >, or * ) to present that new page. FMGC Stuff Now for some general info on the FMGC! DIR key This key is one of the most used and will allow the pilot to go direct to any fix that the FMGC will recognize. If the FMGC doesnt recognize the fix then the pilot can build a temporary waypoint and insert the new waypoint into the direct command to be able to navigate to the fix. This will be gone over more later in waypoints and reroutes. F-Plan Key When you select the F-Plan key the default (normal) Flight Plan view will have the FROM waypoint at the top of the MCDU screen (first line). The next (second) line will be the TO waypoint and all succeeding waypoints will continue down the screen. The FROM waypoint is usually the last VOR or intersection you crossed but it can also be PPOS (Present Position) or T-P (Turning Point). PPOS simply means that you are not on any nav segment and the FMGC is just tracking where you are with no nav guidance available. This will occur after takeoff when the runway is automatically cleared and you dont have a nav segment to join yet. T-P will show when you use the Direct function, which we will go over later. The second line is the TO waypoint and is in white while most of the rest of the lines are in green. However, it is possible that a pseudo waypoint may be on line two and therefore it may be white but not the TO waypoint. We will go over pseudo waypoints later as well. You can always scroll up or down on the F-Plan page but the FROM will always be at the top when you select the F-Plan key. Think of the FROM as being what is 22/05/12 94
Fraud
behind you. Think of the TO as being what is just ahead of you. The FROM is important because to use lateral navigation you must define a nav segment for the FMGC to follow and this means that you must have two points for any given nav situation to define a segment. This will become more clear when we go over Reroutes. DISCONTINUITY is a line that shows two points are not joined and they do not form a segment. If DISCONTINUITY is showing then the FMGC will NOT continue to the next waypoint. Think of it as a gap in your navigation. In fact that is exactly what it is, a gap between two NAV points. This is something that you want if you will be given radar vectors at a certain point. You will most commonly see DISCONTINUITY after the runway when initializing when you will expect radar vectors to your first fix and after the last fix on your route prior to beginning your approach. There are times when you will need to clear a DISCONTINUITY and we will look at that in a moment. If you are in NAV mode and reach a discontinuity in the flight plan the autopilot will just drop to heading mode on the current heading or entered heading if one is entered in the FCU. Note that the Heading window will only hold a heading for 45 seconds (who knows why!) The scratchpad is the bottom line of the MCDU and is where you will enter data. After you type info into the scratchpad you will then select it up into the FMGC by using the LSK (Line Select Keys) on either side of the MCDU. Note that you cannot select data from the FMGC into the scratchpad. You will also get various warnings in the scratchpad and they can be cleared by pressing the CLR key in the bottom right hand corner of the keys. AIRPORT Key The AIRPORT key simply allows the pilot quick access to any airport that is entered into the flight plan. This would include the departure airport, arrival airport and the alternate airport. Press this key and the display will place the next available airport in the FMGC flight plan on the first (top) line in the MCDU. This just gives the pilot a fast way to scroll the flight plan display to the next airport. NEXT PAGE Key The NEXT PAGE key gives access to additional information for some screens when there is more than can be shown on one screen. Think of NEXT PAGE as scrolling horizontally. The F-PLAN and INIT screens use the NEXT PAGE function. When there is more than one page the pages are referred to as PAGE A and PAGE B as in INIT PAGE B. This would require you to select INIT and then press NEXT PAGE to access INIT PAGE B.
Keys: The keys (up/down arrows, slew keys) allow the pilot to scroll a page vertically. You will also use them for changing values. This is most commonly used when adjusting the LAT/LONG that is stored for the airport to the gate value when initializing on INIT. You will also very commonly use them for scrolling the FPlan screen to see waypoints that continue in the flight plan beyond the MCDU screen display.
DIR Key The DIR key allows the pilot to go direct to any waypoint entered. The TO waypoint will become whatever is entered as the direct and the FROM waypoint will become a T-P (position the aircraft is at when the DIR is entered). You may either press the LSK next to the direct fix or type the fix in the scratchpad and press the DIR TO LSK. 22/05/12 95
Fraud
DIR TO Key commutes NAV Mode PROG Key The PROG key will actually access a number of different pages depending on the phase of flight you are in. In every case you will see a PROG page but the name will change depending on the phase. For example, when in cruise flight the page will be name PROG CRZ and in climb PROG CLB and so forth. This PROG page along with F-PLAN will be used most of the time when you are not accessing some other page. The PNF should have PROG on their side unless they need something else. The PROG page will show the planned cruise altitude (as loaded during INIT or as modified) as well as the optimum cruise altitude and the recommended maximum altitude. Optimum (OPT) is based on cost using the COST INDEX you entered. Recommend Maximum (REC MAX) is based on 1.3 G protection and should only be used in smooth air. You may change the planned cruise altitude anytime by coming to any PROG page. Another handy feature is the Bearing / Distance to feature. Just put in any airport or fix and you can immediately see how far you are from it and what heading to take to it. Even better, this is one of the few features that does not crosstalk with the other FMGC so each pilot can load a different fix to use. This is a great place to come when planning a crossing restriction before you get it loaded into the Flight Plan to be sure you wont miss the fix. Finally, PROG is also where you will change the required accuracy for RNAV GPS approaches. PERF Key The PERF key allows the pilot to see and enter data for the various phases of flight. You will use this key when initializing to enter takeoff information, changing climb, cruise and descent speeds and entering approach data. Only the preflight and done phases do not have pages.
96
22/05/12
Fraud
Press the PERF key and then press the LSK at the bottom of the screen to move to the next or previous phase page. If you arent sure what phase the FMGC is in just look at the top of this page as each phase is named here. For example in takeoff phase the PERF page is named PERF TO page and in cruise it is named PERF CRZ page. RADNAV Key The RADNAV key stands for Radio Navigation and is the page to check when you wish to determine which navaids are being tuned. Normally the Airbus will autotune the radios and you will not be aware of what navaids are being utilized. However, there are times that you will need to lock a frequency for tuning, such as when a DME is used for departure on a SID. Just press the RADNAV key and then type the navaid identifier (you may also use the frequency by using a leading slash, for example /115.0) in the scratchpad. Then select the identifier to the VOR1 or 2 LSK at the top of the MCDU. This will keep that side tuned to that frequency. You can use the DDRMI to see raw data. The locked identifier will be in LARGE letters. FUEL PRED Key The FUEL PRED key allows the pilot to view fuel prediction info on destination, alternate and fuel management data. This is the page to use to enter Weight and Balance data. If the INIT page B is showing on the MCDU on engine start the FMGC will automatically rollover to FUEL PRED for weight data to be entered. Gross weight and CG data are entered on LSK 3L. For example, 144,190 lbs. with a MAC of 23.2 would be entered as: 144.2/23.2
INIT Key The INIT key is used when getting ready during preflight. You initialize the FMGC from this page. This page will be gone over in more detail later. SEC F-PLN Key The SEC F-PLN key allows the pilot to have a second flight plan to use for what-if scenarios or to load anticipated changes that might occur in the primary flight plan. You are able to copy the primary flight plan in order to make changes to it or you can program a new flight plan.
97
22/05/12
Fraud
Airbus Gotcha: If Secondary flight plan is different from Active flight plan you
must be on Heading to activate. You cannot change an active NAV segment while NAV is engaged. DATA Key The DATA key will allow the pilot to view the various sources of data for the FMGC and determine whether it is valid or not. MCDU MENU Key The MCDU MENU key allows selection whether to work in FMGC or ACARS or another area such as AIDS. Only one MCDU can be set to ACARS at one time. If the opposite side is selected to ACARS then you will locked out of ACARS until it is selected back out of ACARS. CLR Key The CLR (clear) key is a delete key. You can use it to delete characters or phrases in the scratch pad or to delete data from the FMGC. To clear the scratch pad just press the CLR key and the last entered character will be deleted. If you continue pressing the entire phrase in the scratchpad will be cleared. The CLR key can also get rid of warning messages. To delete data entered into the FMGC press the CLR key while there is nothing in the scratchpad. CLR will be entered into the scratchpad. Now select CLR to the LSK that corresponds to the data you wish to delete. This is how to delete a discontinuity. Press the CLR key and then press the LSK that corresponds to the discontinuity and it will be deleted with the waypoints on either side of the discontinuity now joined as a segment. OVERFLY Key One of the more obscure keys on the MCDU this one has basically only one function. When you are coming up to a waypoint the FMGC will normally compute the turn at the waypoint and due to the radius of the turn the aircraft may begin its turn early to be able to turn smoothly onto the airway centerline. There may be times that you need to actually fly exactly over the fix before turning. In those cases press the OVERFLY key and then line select it up to the appropriate fix as a lateral revision. The FMGC will now make sure to fly directly over the fix even if it will cause overshoot on the far side of the turn. Well, OK, there is one other function for the Overfly key. When using freetext in ACARS you will use the overfly key to put a space in the text as you would use the space bar on a word processor.
98
22/05/12
Fraud
Pseudo Waypoints OK, besides just sounding weird what are pseudo waypoints anyway? Basically they are lines of information on the Flight Plan page that are not something that you can navigate to. They are mostly to do with vertical profile information and are therefore not for lateral navigation. Pseudo waypoints on the MCDU will consist of the following: T/C Top of Climb (hockey stick) T/D Top of Descent (hockey stick) S/C or S/D Start of Climb or Descent for Step Climb/Descent (hockey stick) SPD LIM Speed Limit (M&M) DECEL Deceleration to approach phase (circle D brand) I/P Intercept Point (lightening bolt) Please note that while you cannot navigate laterally using the pseudo waypoints they will show on your ND using various symbols. If a pseudo waypoint is on the second line of the MCDU it will be white even though it cannot be the TO waypoint. The MCDU logic simply makes the second line white whether it is actually the TO waypoint or not. Also you will have some pseudo waypoints that show on the ND that are not on the MCDU such as the Energy Circle and Crosstrack Error. The Energy Circle (green dashed arc) is available only in Descent and Approach phases. It shows how far the aircraft will go until reaching landing elevation in the current configuration until 1500 AGL then configure for landing and descend to landing elevation. It is interesting to note that Flaps 1 provides better range than Flaps 0 (clean). Crosstrack Error will show how far the aircraft is from the active nav segment or leg. This is very useful when cleared for approach or when cleared to join the departure or arrival. The Intercept Point will show as INTCPT on the course when on heading to join the active nav leg.
99
22/05/12
Fraud
Note: Allow at least 3 minutes after initial power up on a cold airplane for all internal tests to be completed before pressing buttons. DATA: Press DATA key, then A/C Status. Check database validity and dates. Enter BIAS from flight plan on PERF for performance factor on LSK 6R. INIT
Page A:
Press INIT key. Enter the city pair codes in FROM/TO. For example, for Charlotte to Phoenix use KCLT/KPHX or use company route number such as KCLTKPHX1.
Enter the alternate city code. Example: for Greensboro use KGSO. Enter flight number. Check lat/long coordinates. If gate coordinates are available use the scroll keys (up/down arrow keys, to adjust coordinates. It is safer to use the airport ) 100 22/05/12
Fraud
coordinates from the database and to scroll in the gate adjustments as this avoids the pilot typing in gross errors that are not caught. Cost Index. Enter 30. Cruise flight level. Enter intended cruise altitude on the CRZ FL (350 for 35,000) and modify the anticipated cruise temperature with /TEMP (/-49 for minus 49). Press the ALIGN IRS key (LSK 3R). ALIGN IRS should be pressed within 15 minutes of turning GNADIRS to NAV to avoid excessive drift. DO NOT move aircraft during align process.
Page B
Press the INIT key.
Enter ZFCG/ZFW and Block Fuel Press the NEXT PAGE key. This will take you to the second INIT page. Check that the reserve time is 45 min. on FINAL/TIME line. F-PLAN
Airbus Gotcha: Delete the pseudo altitude waypoint for the runway (not for
Insert first fix or waypoint in flight plan route. If there is victor or jet airway routing from the fix then use a lateral revision to enter the needed airway. For example for a route from BOS VOR on Jet 75 that ends at CMK press the left LSK next to BOS in the flight plan. Now enter J75/CMK in the VIA/ GO TO. Then INSERT if OK. Any fix that is a direct with no published route you can simply press on the next line. For example to go direct from BOS to CMK simply press CMK on the 101 22/05/12
Fraud
line below BOS LSK. This will place CMK after BOS in the flight plan as the next fix. Note: pressing a fix on top of a fix places the new fix ahead of the previous one and a discontinuity is in between the two fixes now. You will need to clear the discontinuity if you want to join the fixes to make a segment. To clear a discontinuity press the CLR (clear) key and then press the LSK next to the discontinuity. This will join the two waypoint on either side of the discontinuity. Enter any vertical restrictions (cross LAX VOR at or above 10,000) by typing the altitude in the scratch pad and pressing it on the right LSK for that fix. You can also enter a vertical revision by pressing the right LSK for that fix and putting it into the proper field. If you have an at or above clearance put a + in front of the altitude before entering it (use for at or below) Example: at or above 10,000 use +10000, at or below FL240 use 240. Enter any anticipated arrival and approach by pressing the left LSK (lateral revision) for the destination airport. Enter appropriate Arrival, Transition and Runway Approach and Insert if OK. Check distance at bottom of F-Plan page against the total distance showing on Release. This is a gross check and should be close but does not need to be exact as arrival and approach routings may add mileage not on release.
Fraud
directive. In order to read VOR DME use the ADF/VOR selector switch on the EFIS control panel (yes, the one you were told NEVER to use). Just select the appropriate switch to the VOR setting. After takeoff return the switch to the OFF position. SEC F-PLAN Press the Sec F-Plan key. Press the LSK for Copy Active. This will give you a practice copy of the flight plan with which you can later play what if scenarios with if you should so choose or to enter possible route changes (such as different than filed arrivals) to quickly activate as an active flight plan if needed. Note: If Secondary is different from Active flight plan you must be on Heading to activate. If Secondary has been copied then PERF will be available as a prompt on SEC page. This PERF will allow you to enter the performance data for the secondary flight plan After engine start: FUEL PRED After engine start you will use the FUEL PRED key to enter W&B. Enter the actual gross weight (RAMP weight) and CG from the W&B printout on GW / CG on LSK 3L. You will not have to enter the fuel as the FMGC reads it on its own. Example: 133.6/24.8 Before engine start leave the FMGC on the FUEL PRED page and you will have the proper page ready for use. If you receive the Weight and Balance message before engine start you may type the weight and CG in the scratchpad for entry after engine start if you wish. PERF Press the PERF key and you will now be on the PERF TAKEOFF page. Enter V1, V2 and VR speeds on their LSKs. Enter FLEX temp if needed. Enter THR RED/ACC (thrust reduction/accelerate) and ENG OUT ACC altitudes from W&B printouts. Enter the flaps setting and stab trim settings in units of UP or DN on the FLAPS/THS LSK (example: 1/0.5DN or 2/1.0UP). If using an intersection departure enter the distance from the end of the runway to the intersection on the TO SHIFT LSK. Now type the 0 (or clean) speed in the scratchpad. Select NEXT PHASE and put the clean speed in the CLIMB *SPD LSK. This allows the aircraft to accelerate to green dot after takeoff instead of 250. When taking off from an intersection you should enter the amount of distance the intersection is from the end of the runway. For example, in PIT it is common to use runway 28L intersection P. From the TPS pages you can determine the distance available for takeoff (or just ask Ground Control!). Subtract that from the full runway length and you have the intersection 1500 from the end of the runway. Enter 1500 on the TO SHIFT LSK. If approach data (PERF APPR) is not entered within about 180 nm of destination then MCDU will give error message saying so. So go ahead and get approach data loaded, the electrons are free! 103 22/05/12
Fraud
Airbus Gotcha: If not within 200 nm of destination then aircraft will not initiate
descent in PERF DESCENT mode. Descent will be made in PERF CRUISE mode as a cruise descent. During descent in cruise mode the FMGC will not see crossing restrictions in the flight plan.
Airbus Gotcha: The aircraft will not initiate descent automatically from cruise Airbus Gotcha: The pilot cannot change the Descent data once the FMGC is
altitude when reaching a descent point (known as T/D or Top of Descent). The pilot must set in new altitude and then push the ALT knob to enter Managed Descent. in Descent Phase. If you wish to make a change to the FMGC descent speed once you are in Descent Phase, enter a new cruise altitude below your current altitude into the PROG page. This will cause the FMGC to revert back to Cruise Phase and allow you to enter a new descent speed in the PERF DES page. The FMGC may plan a much slower speed for descent in Descent Phase than in Cruise Phase. If the aircraft begins a descent and enters the Descent Phase when you wish to make a faster cruise descent you can enter a new cruise altitude on the PROG page below your current altitude. The FMGC will now revert back to Cruise Phase until crossing the new altitude. Be aware, however, that the FMGC does not see crossing restrictions when descending in Cruise Phase and will only descend at a set vertical speed.
Airbus Gotcha: Managed Climb/Descent is not available on heading. You must be on NAV to use Managed Climb/Descent. Airbus Gotcha: When the aircraft is in HDG mode and the pilot enters direct
to a waypoint the autopilot will automatically engage NAV with no other action on the pilots part. In other words, the autopilot will change modes automatically from HDG to NAV when a DIR is entered in the FMGC. The point here is to be sure of where the waypoint is when you enter DIR as the airplane will automatically turn to the new waypoint as soon as it computes the new course. DIR will always turn the shortest distance to the point. If the aircraft begins to go the wrong place or turn the wrong direction (for example turn left instead of an assigned right turn) use HDG mode until you can correct the problem.
Airbus Gotcha: WARNING: Do not use UPDATE AT on the PROG page! The
Update At feature will shift the FMGC to the new position. This will destroy the accuracy of your FMGC. Note: does not affect IRUs. restrictions will delete pilot entered crossing restrictions and you will have to reenter them.
Airbus A319, A320, A321 Notes LAT/LONG (latitude / longitude) P/B/D (Place / Bearing / Distance) P-B/P-B (Place Bearing / Place Bearing)
Fraud
Example: 3551.5N/08158.3W (dot, slash, dot) Example: CLT/314/64 (slash, slash) Example: CLT314/HMV171 (dash, slash, dash)
Note: waypoint slewing or uptrack/downtrack on the course using a + or is NOT available. Use a P/B/D on the course if possible. Note: In the flight plan on the MCDU a P/B/D is shown as a PBD. The pilot created waypoints will be numbered so the first PBD is shown as PBD01 and the second as PBD02 and so on. The P-B/P-B waypoints are shown as PBX so they appear as PBX01, PBX02 and so forth. LAT/LONG waypoints are shown as LL01, LL02 and so forth. To make a lateral revision to flight plan (F-PLAN button selected on FMGC) press a LSK on the left side of the MCDU (LSK 1L through 6L). To make a vertical revision press a LSK on the right hand side of the MCDU (LSK 1R through 6R). To enter a new destination (diversion not to alternate) use a lateral revision on any waypoint in flight plan (NOT current destination) and then enter NEW DEST on LSK 4R. To enter holding into flight plan use a lateral revision on intended hold point then press the HOLD LSK on 3L.
105
22/05/12
Fraud
Auto Initialization
One of the nicer features that has been added to the Airbus is FMS Uplink or Automatic Initialization. Now that we have gone over how to do it manually (and sometimes you will still do the manual method if uplink doesnt work) you can learn the auto method. You will still go to the DATA page and check the database as in the manual method. Next, go to INIT as before but now you can select the INIT REQUEST* 2R LSK. This will send a request through ACARS to uplink your flight plan data. The INIT page will be filled in automatically as well as the F-PLAN page. Pretty cool, Huh? Of course it isnt quite that simple so lets go over the things you need to be aware of. During the uplink you will see a pause (if you are watching on the INIT page) before the COST INDEX and CRZ FL are filled in (they change from dashes to box prompts at this point). This is to allow you to enter the appropriate flight level from your printed flight plan before the Wind Data is sent. When the pause occurs just type in the cruise flight level and cost index. If you arent sure (as when the F/O is still waiting for the release paperwork to show up) then simply wait during the pause and the process will continue but the Cruise Winds wont be sent. I have no idea why the cruise level winds cant be sent since the FMS uplink enters the flight level and cruise index as they are the same as the release paperwork but whatever. If you must bypass the winds you can enter them manually later from the release Auto INIT will not fill in your Alternate so you will need to go back and fill that in. The F-PLAN page will also be sent but you must be aware of several things. First, any departure or arrival routing will not be sent. In other words, you must enter the runways and SID and STAR routing as in the normal manual method. Secondly, occasionally there are gaps in the flight plan. So always check the flight plan as you would in the manual method to ensure you dont have missing fixes or discontinuities that shouldnt be there as I have found both in uplinked flight plans. Normally if I have paper work I will do the uplink after getting back to the cockpit after my walk around. If I dont have the paperwork I just press the INIT REQUEST* before the walk around and let it uplink while I am out since I dont have to worry about the pause. Note: if something goes wrong during the uplink and you need to start over just go to DATA and select the other database. Now select the proper database for use again. This will clear all entered data for the flight and you will start over clean. After engine start enter the data on the FUEL PRED page just as in the manual method. Then go to the PERF page as you normally would. You will see a message in the scratchpad once the performance data has been sent saying TAKE OFF DATA UPLINK. Just clear the message. That is followed by PERF DATA UPLINK. Clear this as well. Now you can automatically enter the TAKEOFF PERF page! Press <UPLINK TO DATA on LSK 6L Press <RECEIVED TO DATA on LSK 6L If FLEX data is being used press FLEX TO> on LSK 4R Note: if no FLEX is available press the MAX TO> prompt to see TOGA power data. If proper runway data is not showing press the NEXT PAGE key. Up to four runways are shown. Once the proper runway is shown, Press INSERT UPLINK* on LSK 6R Please note that you can only get an INSERT UPLINK* prompt if for the data for the runway that is selected on F-PLAN. If you cannot get the prompt make sure you have the proper runway selected. Obviously if there is a runway change during taxi out you must change the runway on F-PLAN and then re-enter the uplink data on TAKEOFF PERF page.
106
22/05/12
Fraud
The data uplink will not enter the clean speed for you so after entering all the uplink data go to NEXT PHASE and enter the 0 or clean speed just as you do with the manual method. TPS will show you whether to plan on FLEX or TOGA power. TPS will also show you which runways will be sent and the top flap setting is the one you sent in the uplink. If you need something else you will need to contact load control to change the uplink.
107
22/05/12
Fraud
Phase Triggers
I think phaser triggers belong in Star Trek but these are phase triggers. Phases are very important and you can look at the top of the PROG and PERF pages to see what phase you are currently in. You will better understand how the Airbus FMGC thinks if you understand what triggers the phase change. Taxi to Takeoff Flex (if FLEX loaded in FMGC) or TOGA thrust lever detent selection Takeoff to Climb Reaching the thrust reduction / acceleration altitude loaded in the FMGC during initialization on PERF page. Climb to Cruise Reaching planned cruise altitude listed on PERF page. Cruise to Descent Start of descent from current cruise altitude (within 200 nm of destination). Descent to Approach Activate and Confirm Approach on PERF DES page. This will drive managed speed to approach speed. Note: If the ECAM takeoff memo hasnt yet come up on the screen during taxi just press the T.O. CONFIG test button on the ECAM control panel. This will force the taxi phase and the ECAM takeoff memo screen to come up. Note: If descent is initiated before 200 nm from destination then descent will be made in CRUISE DESCENT at 1000 fpm and will not honor any descent crossing restrictions. The FMGC will prompt for a new cruise altitude as a warning.
Imaginary Centerline
You may have had an imaginary friend in your childhood. I didnt. We wont talk about yours. However, the Airbus does have imaginary extended centerlines that you can use. If you have been vectored off course and are cleared to join a radial but dont have the nav segment available you may be able to join it with no reprogramming at all. In this example you are on an arrival and vectored off course. Then you are cleared to rejoin the radial for the arrival. However, the current nav segment has already been cleared. As long as the next segment is the same radial the FMGC will still join the imaginary extended centerline of the next nav segment. This will also work in the case of being vectored for final approach. If you are vectored to join outside the defined nav segment the FMGC will still join the extended centerline. Just press NAV engage and as long as the present heading will cross the extended centerline it will join at the point of crossing. The display will not show a nav line but it will show miles left or right of course until on the actual nav segment. 108 22/05/12
Fraud
Auto Clear
I dont have any technical info on this one so I just call it auto clear. When on heading if you go past a waypoint there is some FMGC logic that says you wont use that waypoint and it will automatically clear it. This happens most often on close vectors for approach near the approach course on downwind.
Reroutes
One area that gives many new Airbus pilots problems is making changes to the FMGC flight plan once under way. There are several very common ways to enter reroutes into the FMGC, depending on the nature of the reroute. Direct: Press the DIR key and type in the fix (VOR or intersection). Press the LSK 1L key to enter the fix. The FMGC will automatically enter a T-P (turning point) to create a FROM waypoint and the fix that is entered will become the TO waypoint. Direct then as filed: Use the above method or press the DIR key and then find the cleared fix in the flight plan. Press the LSK next to the desired waypoint and it will become the TO waypoint. Using either method all waypoints before the fix are now cleared and the remainder of the flight plan will be available as filed. Note: if you are on heading when DIR is used the mode will change to Managed NAV automatically (in other words, when you go direct in heading mode the aircraft will automatically engage NAV and go to the direct fix). Heading to intercept then as filed: Select the cleared intercept heading on the HDG selector on the FCU. Then you must determine if the segment you have been cleared to join exists in your flight plan. If it does you only have to clear any waypoints that are ahead of the segment until you have the proper fix as the TO waypoint. Use the CLR key to clear any unwanted waypoints then engage NAV. If the needed segment is not available you must build it. As above first select the intercept heading. Then type in the fix that will become the FROM. Remember, in this case you have to create a NAV leg (segment) that does not currently exist in the FMGC. After typing the new FROM select it to the LSK 2L key and it will become the TO. Now enter the TO fix on the next line if it does not already exist. This creates the new leg segment. Now clear the T-P (turning point) on 1L (clearing the T-P allows each fix to move to its proper TO and FROM position). Then engage Managed NAV. You can now add any other needed fixes until on the original route. Then clear any remaining discontinuities. Offset: To parallel your current course use a lateral revision at the FROM waypoint. Type in the amount of distance (up to 50 nm) to the side you wish to parallel the current course and right or left of course. For example for 20 miles left of course type 20L and for 35 miles right of course type 35R. Now select the amount into the OFFSET prompt on LSK 2L. You can see the anticipated new offset course on the ND. If you wish to adjust it press ERASE and type in the new amount. Once satisfied with the new course press INSERT. Aircraft will take a 45 cut to the new course. To resume the original course access the same OFFSET prompt and clear or go DIRECT to a fix on the original flight plan.
109
22/05/12
Fraud
New SID: Press the LSK 1L key for the departure airport. Now select DEPARTURE, then select the departure runway. If you are using a SID select the appropriate SID (NOTE: you may have to scroll to see all available SIDS). If there is a transition to the SID you can select it on the right side of the MCDU. Once everything is selected press INSERT. New STAR or Approach or Runway: Find the DEST (destination) airport at the bottom of the Flight Plan page on LSK 6L. Press the left LSK for the airport for the lateral revision page. Now select ARRIVAL on LSK 1R. Select the appropriate approach and/or runway if needed. Scroll as needed to see additional approaches if the needed one is not on screen. If you dont need a new approach or runway simply press Next Page to see the arrivals. Next select the appropriate STAR (NOTE: you may have to scroll to see all available STARS). Now select any transition as needed on the right hand side of the MCDU. When all has been selected press the INSERT prompt on the 6R LSK. If a transition is used that is already in the flight plan then there will not be a discontinuity to clear in the flight plan. However, if you do not have a transition then please be aware that the arrival and the flight plan will not have a common point and therefore will have a discontinuity.
Airbus Gotcha: Changing the STAR, approach or runway will delete any
pilot entered crossing restrictions on an arrival. Make sure you confirm any crossing restrictions after making any arrival changes. New Route: To enter a new route you will program just like you did for the flight plan initialization. Take a lateral revision (left LSK) from the last common fix. Then use the VIA/ GOTO in the following format J75/BOSOX. If the new flight plan ends in a common fix then there will be no discontinuity and no fixes to clear. However, if the routing results in no common fix then you will need to go back and clear all the old fixes. Holding: Press the left LSK for a lateral revision at the holding fix. If the fix does not appear in your flight plan (you are really having a bad day!) then use DIR first to enter the fix. Now press the HOLD selection on LSK 3L. If the hold is as published then check all data on the DATABASE HOLD page and if it is all good then press INSERT on LSK 6R. If you need to make changes or there is no published hold (COMPUTED HOLD) then make the needed changes to the Inbound Course, Turn Direction (L or R), and the time or distance needed for legs. Once all data for the hold is good press the INSERT selection on LSK 6R. For immediate hold, take lateral revision at FROM waypoint and select <HOLD. New Destination: Make a lateral revision from any waypoint in the flight plan (not an airport) by pressing the left LSK for that waypoint. Now select the NEW DEST prompt by typing in the new airport identifier (example: KCLT for Charlotte) and pressing the LSK 4R key. You may now go to the flight plan to modify the arrival information as needed for the new destination. New Alternate: Press the left LSK for a lateral revision from the destination airport. The select the <ALTN prompt on LSK 5L. Enter the new airport identifier on the blue line on LSK 3L over the old alternate or in the brackets if there was no alternate. Now press LSK 3L again to select the new alternate. Now press INSERT. Alternate should now be entered in the flight plan and on the FUEL PRED page. 110 22/05/12
Clock
TAKEOFF
Airbus Gotcha: It is possible for the F/O to occasionally enter the wrong
W&B data. An easy way for both the Capt. and F/O to double-check their work is to look at the Gross Weight shown in the bottom right hand corner of the SD after engine start and W&B is entered. This number should be very close to the Ramp weight shown on the W&B printout. If you manage to still takeoff with the wrong gross weight entered, you will eventually get a gross weight mismatch error message once the aircraft has computed its in-flight weight. To correct this, just enter the proper weight in the PROG page after subtracting the current fuel used from the original Ramp weight.
Airbus Gotcha: If on taxi out you do not have the V speeds showing in your
PFD (after entry in MCDU), make sure that your Flight Director is turned on. On takeoff, PF should have the F-PLN page, PNF the PERF-TAKEOFF page Use a radar tilt of 5-8 UP if radar required during takeoff.
Normally set a departure heading for selection at 400. Note: set the heading you will need at 400. If you are using a SID departure where NAV is required NAV mode will engage at 30 automatically, do not set a heading for NAV departure. Use ARC or ROSE NAV on takeoff on your EFIS ND settings. Do not fly around in PLAN. Only use PLAN as a momentary reference in-flight.
Make your flight instructor happy!: When setting power for takeoff, the thrust levers should be set to 50% on the TLA (doughnut) and once both engines stabilize at 50% then position both levers to FLEX or TOGA. The 50% setting will be at about the H on the thrust lever index where the pedestal says A/THR (to give you an idea of how far forward the thrust lever goes). Make an initial setting on the thrust levers and then adjust on the TLA to 50%. Do not use aileron into the wind during a crosswind. During a takeoff with crosswind exceeding 20 kts. or CG more than 34% apply full forward sidestick to be taken out by 80 to 100 kts. Ensure the aileron is neutralized by looking at the control pointer cross on the PFD or relax the sidestick to center during the takeoff roll. This will ensure that you do not have any roll in the initial rotation and liftoff. During crosswind takeoff let engines stabilize at 50% then increase to 70% N1 and stabilize, then increase to FLEX or TOGA by 40 kts. ground speed. On takeoff the aircraft will blend from direct to normal law as it goes from ground mode to flight mode. This means that the backpressure that you need to hold the nose up will reduce to zero once normal law autotrim activates. You will usually not really notice this change as the aircraft will be climbing quickly but you will learn to release the backpressure around 100 to 200 ft. as the trim kicks in or the nose will balloon. A good Airbus pilot quickly learns to minimize input as many times the pilot is inducing a slight amount of sidestick pressure without realizing it.
Fraud
Remember, the less input on the stick the better. You dont want to confuse the computers (or the pilot!). New Airbus pilots tend to get into the habit of slapping the Thrust Levers back from TOGA or FLX/MCT to the CL detent. While this will work it really isnt the best technique. The power reduction will be very noticeable in back to the passengers and is harder on the engines when using TOGA or less aggressive FLEX reductions. When the FLEX temp is around 60 there will be little or no reduction when coming out of FLX/MCT to CL and this is why pilots get used to just slapping the levers back. However, when the reduction is in the 30 range or so (common on the 321) or at TOGA the immediate reduction is very noticeable. Remember that when above CL you are manually controlling the thrust but the FLEX has capped the thrust so that with large assumed temps there is little or no change from FLX/MCT to CL. Just ease the thrust levers back from FLX/MCT or TOGA to the CL detent slowly just as you would on any other jet aircraft. Your passengers and engines will appreciate it!
It commands: 1. V2 if you are not yet there. 2. V2 + 10 with both engines 3. V2 is you are single engine, it will fly the existing speed if above V2 NOTE: At heavy takeoff weights, the S speed on the A321 may be higher than the MAX speed of CONF 1 + F (225 knots). In this scenario, is it permissible to retract the flaps/slats at speeds below S speed?
No. At heavy takeoff weight, the S speed on the A321 may be higher than the MAX speed of CONF 1+F (225 knots). In this case, continue to accelerate. On reaching 210 knots the automatic flap retraction will occur and the MAX speed will move to 235 knots.
V1 Cuts
Pick a line and stick to it no matter what on every takeoff. You will find that you will just naturally put in the correct rudder for V1 cuts if you practice this on every takeoff. You dont have to hit the centerline lights but stay right on the centerline. You should have the aircraft already stabilized with rudder before rotation (assuming the cut is before the Rotate call). Bring the nose up to 10 (park it on the 10 shelf) and hold it. Then follow the flight director. The only real gotcha here is that the aircraft takes off in Direct mode. It will then blend to Normal. This means that you will have autotrim kicking in just after takeoff. Remember in direct you will be holding back pressure to keep the nose at 10 until Normal law with autotrim comes in and then you will need to release the back pressure on the sidestick. In fact this is what happens on every takeoff. Be sure that you dont try to trim off the rudder so quickly that you are diverted from flying during the blend from direct to normal as the trim coming in will cause you to pitch up if you arent watching for it. Since technically the autopilot can be put on at 100 some folks try to show how good they are and start trimming rudder right away. Better to wait 113 22/05/12
Fraud
until the blend is complete around a few hundred feet first and then trim the rudder and then get it on autopilot. You dont get any bonus points for a quick rudder trim but losing speed and pitch control!
114
22/05/12
Fraud
Activating the approach will drive managed speed to approach speeds. Suggest activating the approach when out of 10,000 and on selected speed. If you accidentally activate the approach you can simply use Speed Select for remainder of flight or enter current cruise altitude on PROG page for CRZ altitude. Entering the current altitude as the cruise altitude on the PROG page will force the FMGC back to Cruise phase. Once on vectors with approach control you can clear out any remaining flight plan in the FMGC that is not needed to allow only the planned approach to be shown. This is sometimes referred to as clean up the box. Both Flaps FULL and Flaps 3 are normally available for landing. So far I prefer Flaps FULL better. Note: If flaps 3 is to be used then CONF3 should be selected on PERF APPR page and the overhead GPWS LDG FLAP 3 pb ON . When using approaches that utilize barometric settings (MDA, DA) such as ILS CAT I, LDA and RNAV the minimums setting is on the MDA line (line select key 2R) on the PERF APPR page. Autocallouts are not available at 100 above and minimums when using the MDA setting. When using approaches that utilize radar altimeter (DH, AH) such as ILS CAT II and CAT III the minimums setting is on the DH line (line select key 3R) on the PERF APPR page. Autocallouts will be made at 100 above and minimums.
Make your flight instructor happy! When putting the landing gear up, disarm the ground spoilers by pressing the speedbrake handle down. When putting the landing gear down arm the ground spoilers by pulling the handle up.
When extending flaps to the final position say Flaps Full not Flaps 4, and when retracting flaps to the fully retracted position say Flaps UP, not Flaps 0 (zero). Do NOT add the word to as in Flaps to 3. Make your flight instructor happy!: When making any change in modes such as arming an approach or turning off the flight director or autopilot make sure you look at FMA (at the top of the PFD) to see what mode you actually are in. On every approach be sure that by 100022/05/12 115
Fraud
Speedbrake is stowed SPEED is showing in FMA or autothrust off Not on Open Descent (inside FAF for instrument approaches)
Airbus Gotcha: If you find that you cannot get the proper ILS frequency and
course showing on the PFD when you select the ILS pb, then check your RAD/NAV page and see if a navaid has been entered and is locking out autotuning. Also be sure that an RMP NAV pb is not selected as this will turn on the NAV backup mode and disable FMGC tuning. I have also seen this simply glitch and not display when it should. We were able to fix it by reselecting the runway/approach. On all instrument approaches (except CAT II,III) PNF calls 100 above, then at minimums, Minimums, runway in sight or Minimums, no contact. PF responds to minimums calls with either Landing or Go Around. Remember: WAFPPP for working in the sim. Weather Advise (ATC, F/As, company) FPLN (insert new destination if needed, then new approach) PROG (if RNAV approach, insert .3 nm RNP) PERF (ACTIVATE and CONFIRM, then insert approach data on PERF APPR) PRELIMINARY (call for Preliminary Landing checklist) It may be helpful to notice a backward Z flow to the keys on the MCDU when doing the F-Plan, RADNAV, PROG and PERF for the approach. You can use this backward Z for any PRELIMINARY checklist flow. VAPP The approach speed is automatically computed by the FMGC (of course!). This VAPP Target is shown on the PFD airspeed scale as a magenta triangle. VAPP is shown on the PERF APPR page on the FMGC. It is computed by taking the highest of two different figures. After you enter the steady state winds (no gusts) and the approach runway the FMGC figures the headwind component. It then takes 1/3 of the headwind and adds this to VLS. However, VAPP cannot be less than 5 kts. above VLS or more than 15 kts. VLS + 1/3 headwind component = VAPP So for runway 18 a wind of 180 at 30 kts. would result in a VAPP of +10 kts. If VLS is 120 then VAPP would be 130 (+10). With runway 18 and wind 270 at 20 the VAPP would be +5 as a minimum of plus 5 must be added and a crosswind adds no additional speed. Now comes the other way to figure VAPP Target, the infamous GS Mini. While it sounds like either a new Mini car or a new mini-skirt style it will actually figure the safest minimum ground speed for your approach. Remember, the GNADIRs know your ground speed and the wind the aircraft is experiencing at the moment. You entered the runway so it can now know what the ground speed should be on 22/05/12 116
Fraud
approach. GS Mini takes the VAPP that has been already figured (130 in our example) and then subtracts the whole headwind component from it. This leaves only the ground speed and the previously added 1/3 wind cushion of 10 kts, so in this case 130 30 = 100 kts. ground speed. While this sounds slow remember that VLS was 120. If we had a head wind of 30 kts. that would result in a ground speed of 90 kts. So you can see that the cushion has actually added 10 kts. to the minimum ground speed. If the FMGC sees the ground speed going below the minimum of 100 kts. then it will increase the VAPP Target to maintain the minimum ground speed. This will ensure that even if all headwind was lost at once that the aircraft has sufficient energy to fly through the loss of speed. GS Mini may increase the VAPP beyond the normal plus 15 limit to maintain the minimum ground speed required. VAPP headwind component = GS Mini The VAPP Target will be the higher of these two airspeeds, VAPP or GS Mini. One point to remember when putting in the wind component. It wont help you to cheat and put in a greater wind than actually exists. Putting in a greater wind speed will actually result in a lower GS Mini (remember the FULL wind speed is subtracted from VAPP) which will result in less protection on approach. If you wish to increase the VAPP Target it is better to simply enter the desired VAPP speed on the PERF APPR page while using accurate wind numbers. While the FMGC will add airspeed for headwind components it will not add anything for crosswinds. It will be up to you to add anything to VAPP on the PERF APPR page if you have heavy crosswinds and you wish to have additional airspeed on the VAPP Target. You will only have VAPP target shown when in APPR phase. You can force the FMGC to approach phase by selecting PERF and then ACTIVATE APPR PHASE and *CONFIRM APPR PHASE. This will drive the managed speed to approach speed. Normally you will be on speed select when you do this but when you command speed engage the speed will be VAPP. Note that VLS will change depending on the flaps configuration selected and therefore the VAPP will also change with landing flap configuration. All approaches must be briefed on the following outline. Use the following aids during your approach briefing: Approach chart: Approach name and runway Approach chart date TDZE Highest MSA Final approach verification altitude (not required for visuals) Required visibility (not required for visuals) PFD (be sure LS pb is selected for ILS): ILS frequency (does not apply for RNAV approaches) Final approach course DA, DH or AH as applicable (not required for visuals) F-PLN page: Glide path angle (RNAV only) Missed approach procedure review (not required for visuals) 117
22/05/12
Fraud
SD: Brief aircraft model (i.e., A319, A320 or A321) and check landing weight. Also include in brief any other considerations such as noise, windshear, antiicing, runway conditions, 10-7 page engine-out procedures, etc. Note: for RNAV approaches be sure to enter 0.3 RNP on the PROG page to ensure FMGC accuracy prior to the approach. Be sure to check that the 0.3 is showing on both MCDUs. NOT that it has happened to me but if you forget what aircraft model you are in here is the gouge. On the ECAM DOOR/OXY page on the SD check the number of overwing exits and slides if there are: A319 A320 A321 One exit and one slide Two exits and one slide Two exits and two slides
(OK, the DATA key, <A/C STATUS page will also show aircraft type as well but that requires pushing keys.no fair!)
118
22/05/12
Fraud
ILS Approaches
ILS 1 is displayed on PFD 1 and ND 2 ILS 2 is displayed on PFD 2 and ND 1 ILS pb should be selected before approach briefing so pilot can read ILS freq., and course off of PFD. This allows the pilot to double-check the actual ILS being used as well as ensures that the ILS pb is selected before the approach begins. If wrong ILS freq. is showing make sure that RADNAV ILS is cleared. Note: if ILS pb is not selected when approach is armed then ILS will flash in amber on the PFD DA - If the approach uses a DA then the barometric altimeter is being used and no autocallout will be made for 100 above or minimums. Enter DA information in MDA position on approach page in MCDU (PERF APPR). DH or AH - If DH or AH is being used then radio altimeter is being used and autocallouts are available for 100 above and minimums. Use the DH line select key for entry of minimums information in MCDU (PERF APPR). When cleared for approach press the APPR pb on FCU. Then press to engage the second autopilot on FCU. Both autopilots should be engaged for all ILS approaches. Note blue GS and LOC on FMA indicating glideslope and localizer are armed for capture. Disconnect autopilot prior to 40 ft. below DA for CAT I ILS
Fraud
If CAT 3 Dual is not shown in the FMA (for example CAT 3 Single or CAT 2 Single) then DH must be used if doing a CAT II or III and runway must be seen. If CAT 3 DUAL is displayed in INOP SYSTEM without any other failure being detected: Change AP in command If it fails: Make a FAC reset: FAC1 pb OFF then ON Wait for FAC1 fault ECAM warning disappears FAC2 pb OFF then ON
Dual will be shown when both autopilots are in use, and Single when only one autopilot is in use or loss of some other required redundant system. Engine-out approaches limited to CAT IIIA (CAT 3 Single, requires 50 DH). Captain retards throttles on the 10 Retard callout, disconnect autopilot by 60 kts. on runway. The autoland fail light will flash red if the following conditions occur below 200 while in LAND mode: Both APs off below 200 RA Excessive LOC ( dot above 15 RA) or GLIDE (1 dot above 100 RA) deviation LOC and GLIDE scales flash Loss of LOC (below 15) or GLIDE (below 100) signal Difference between radar Altimeters is greater than 15 (FD bars flash) LAND green on FMA at 400 ft. indicates that the autopilot is locked in and will ignore inputs on the FCU (autopilot panel). Basically it is only looking for a TOGA selection or to complete the landing.
120
22/05/12
Fraud
If auto callouts are not available the F/O (PNF) will need to make the 100 Above and Minimums callouts. Autopilot should be disconnected on ground before 60 kts. Remember that the autopilot will be steering the aircraft through nosewheel steering until disconnected. Use published CAT I DA on PERF APPR MDA prompt Note: when doing autoland during CAT I or better weather the ILS hold line is not being protected and signal may be poor. ATC has a long checklist to run before CAT II/III is actually flown and this will not be done during CAT I weather.
121
22/05/12
Fraud
Airbus Gotcha: Be sure to get down to final approach altitude prior to FAF to
capture from below!
122
22/05/12
Fraud
Fraud
Both pilots should continue to use the PFs NAV display to monitor approach progress and improve situational awareness.
Engine-Out Approaches
All single-engine approaches follow the same procedures as normal two engine approaches except that Flaps 3 will be used in all cases. The aircraft is certified for autolanding with single engine operation down to CAT IIIA single which will allow autoland approaches down to a DH of 50.
124
22/05/12
Fraud
Visual Approaches
Airbus Gotcha: Both Flight Directors should be turned off when cleared for
Open descent prohibited below 1000 AGL on a visual approach (U)
visual approach and hand flying. This will ensure SPEED is showing for Thrust on the FMA and will help avoid unwanted thrust excursions. Once established on the final if you have instrument guidance (either ILS or RNAV) you may turn the F/Ds back on and select APPR if you will follow the Flight Director.
When using speed select (manual speed selection blue bug) I suggest the following speed ranges for a given flap setting. Note that this is based on my observation of managed speed, not on a written profile, and is simply my suggestion of comfortable speed ranges for a given flap setting. Of course you are able to select from VMO down to VLS whenever needed but the following are suggested as flexible and comfortable speeds to use in line operations. As well, by using these ranges you have a visual reference in front of you at all times: Flaps 0 down to green dot (suggest about 210) Flaps 1 below VFE NEXT down to S speed (green S) (suggest 190) Flaps 2 below VFE NEXT down to F speed (green F) (suggest 170) Flaps 3 below VFE NEXT down to F speed (green F) (suggest 160) Flaps Full or 3 Managed Speed before 1000
Note: recall that VFE NEXT is the amber equals sign on airspeed scale Note: A321 may need slightly higher suggested speeds at heavy weights. The alternate ILS technique works well for conservative Visual approaches as well (assuming on glideslope) and is similar to RNAV technique. If you plan on using this technique the FAA wants you to state alternate ILS technique in your approach briefing. (in parentheses is full ILS equivalent): Plan and configure to arrive prior to 3 nm from FAF with Flaps 2 3 nm from FAF gear down (Dot and a half G/S) 2 nm from FAF flaps 3 (Half dot G/S) 1 nm from FAF flaps FULL (G/S intercept)
125
22/05/12
Fraud
Go Around
Set thrust levers to TOGA, this will activate go around mode and (if turned off) will turn on Flight Director. Go around flaps are to select one step up from the approach flap setting (i.e. if flaps Full, then select flaps 3, if flaps 3 then select flaps 2). During acceleration when at F speed go to flaps 1 whether you are at flaps 2 or 3. If you were in selected speed during the final, GO-AROUND will NOT set SRS: you have to ask quickly for Managed speed. Single engine go around follows same procedure (but will always be from Flaps 3 approach setting as final flap). At acceleration altitude begin engine out clean up procedure (altitude hold, F speed flaps 1, S speed flaps 0, etc.) Note: If performance is not an issue during go-around the thrust levers may be brought back immediately to the CLIMB detent once the go-around mode is activated and MAN TOGA SRS GA TRK on FMA is verified. Once TOGA is used please note that autothrust is now manually set and WILL NOT reduce until brought back to the Climb detent by the pilot (as during a normal takeoff). This means that the autothrust will not reduce on level out while in TOGA detent. If you are rapidly approaching an altitude in TOGA you must bring the thrust levers back to the Climb detent. When in TOGA the aircraft will continue to accelerate when level until it hits the Vmax limit and Normal law takes over. The long and short here, if you TOGA on go around be ready to reduce thrust faster than normal if leveling at a low altitude. If LVR CLB flashes in the FMA you may reduce to Climb Power (CL) detent.
126
22/05/12
Fraud
Landing
Note: these are my personal tips and not necessarily procedures. Bring thrust levers back to idle at about 30 in normal conditions. Flaps 3 will not slow as quickly and you may wish to reduce to idle closer to 50 more often here. The aircraft has plenty of airspeed and energy with managed speed being flown and you will not need to delay thrust reduction to ensure proper flare in normal conditions. In gusty condition you may want to carry thrust longer. Dont let nose drop when normal nose down pitch is added at 50 in flare mode. I was used to flying smaller (and shorter geared!) jets and found it helpful to move my aim point on the runway from the 1000 marker to halfway between the 1000 and 1500. Try to have the flare started by the 10 call. Do not carry thrust to the flare as the autothrust will begin to command climb thrust as speed deteriorates if you do not bring back idle. This will cause a thrust bump that will have you floating down the runway with excess energy. On touch down use positive nose down to lower the nose. Be careful not to let the nose ride up when reverse is selected. Select Full Reverse as you lower nose. As the aircraft slows through 80 knots slowly push the thrust levers back toward idle reverse so as to be at or near idle reverse at 60 knots. Be sure you push the thrust lever all the way back through the detent into forward idle. Then retard the lever again against the stop to ensure minimum forward thrust in idle. Flaps 3 landings will tend to float more than Flaps Full. Be very careful when using Flaps 3 on shorter runways that you ensure touch down in a timely manner. Aircraft seems to level out in flare with Flaps 3 more quickly than with Flaps Full. Use a more subtle flare with Flaps 3 than with Flaps Full. Crosswind Landings Despite rumors, the Airbus uses conventional crosswind landing technique. Two points however: First, as the Airbus uses roll rate for the ailerons the pilot cannot HOLD the sidestick in the crossed control position. The sidestick must be released once the bank angle is established. Think of bumping in the needed bank. It is more intuitive than it sounds! Second, the sidestick is as sensitive in the flare as in cruise. Care must be taken to use measured inputs to the sidestick. The PH recommends aligning the aircraft with the runway centerline during the flare with the rudder. I normally use about 50 ft. to start aligning the nose. Maintain the aircraft on the centerline with roll control. Release all roll input when the aircraft is on the ground. A persistent myth is that the Airbus will blend back to direct law during the flare mode. This is not true. The aircraft remains in normal law but normal law has a flare mode that adds a pitch down at 50. Why do they add this pitch down? It is actually due to the autotrimming in normal law. If you didnt have a pitch down to hold against then when you began your flare the autotrim would just trim off your flare. Then you would balloon and pitch over, it would retrim and you would start all over again. So the pitch over is to give you an artificial back pressure to feel during the flare but it is not a blend back to direct. You will go to direct once you are on the ground. 127 22/05/12
Fraud
Another misperception is that some folks will reduce the power very slowly. However, remember that autothrust is active until the thrust levers are all the way to idle (assuming autothrust is already active). So once you bring the thrust levers out of the Climb detent you arent actually reducing thrust until the levers get all the way back to where autothrust has them commanded. You will only be limiting the amount of thrust that can be commanded. If you bring the levers back slowly you are only reducing the maximum amount that can be commanded but not actually reducing the thrust until you get them very far back. If you wait too long you get the thrust bump we just talked about as autothrust is still trying to maintain the speed. In gusty conditions dont be afraid to use the full throw of the sidestick! In normal smooth air the stick can be very sensitive to slight pressures and is easy to overcontrol. However, in gusty conditions you may need to use full throw of the sidestick. There is actually some lag time from when you command full left or right roll and when the controls actually get there. If you dont believe me watch the next time you do the flight control check. Quickly position the sidestick to full left or right and watch how long before the position indicators take to get there! Even if the lag is just in the indicators I have had the Airbus be slower than I wanted when commanding full aileron so the point here is if you think you need full roll authority go ahead and put it in. You can always take it back out if you dont need all of it.
128
22/05/12
Fraud
TO
The really short list of Airbus acronyms and abbreviations: (before you get to it try to figure out what THS is) Stands for ALPHA as in PROT. Refers to Angle of Attack. ACM Air Cycle Machine ACP Audio Control Panel, allows pilot to select which radios or interphones to listen to. ADIRS - Air Data Inertial Reference System, now replaced by GNADIRS ADIRU - Air Data Inertial Reference Unit AMU - Audio Management Unit ASAP as in LAND ASAP, As Soon As Possible (this really is listed, I'm not making this up) A/SKID - Anti-skid BSCU - Brakes Steering Control Unit (computer) BTC - Bus Tie Contactor CFDS - Centralized Fault Display System CRC Continuous Repetitive Chime, used to be called the fire bell. DDRMI Digital Distance and Radio Magnetic Indicator (RMI with DME) DMC - Display Management Computer DU - Display Unit (CRT, or "TV screen") ECAM - Electronic Centralized Aircraft Monitoring EIU - Engine Interface Unit ELAC - Elevator Aileron Computer EO - Engine Out E/WD - Engine/Warning Display, upper display for aircraft systems. FAC - Flight Augmentation Computer 129 22/05/12
Airbus A319, A320, A321 Notes FOM Flight Ops Manual FCU - Flight Control Unit (autoflight panel)
Fraud
FMGC - Flight Management Guidance Envelope Computer, what actually performs the computations when you type into the MCDU. FMGS - Flight Management Guidance Envelope System F-Plan - Flight Plan FPA - Flight Path Angle FWC - Flight Warning Computer FWS - Flight Warning System GCU - Generator Control Unit GLC - Generator Line Contactor GNADIRS Global Navigation Air Data Inertial Reference System, GPS, Air Data information and Inertial attitude/guidance all in one. Green Dot Best L/D (lift over drag) speed, normally used as the target speed at end of takeoff or for single engine climb out. Technically called VFTO (Final Takeoff Speed). On the Airbus a green dot on the airspeed scale. IDG Integrated Drive Generator (the old CSD and generator all in one unit) INIT - Initialization JFA Just Flying Along, used a lot in ground school as in: there you are just flying along when the demodulator quits causing the blah blah ECAM blah blah amber FAULT blah blah second channel blah blah and thats all there is to it. L/G - Landing Gear LGCIU - Landing Gear Control Interface Unit (I think this one is extra credit, we just called it the linguini) LSK - Line Select Key (keys used on MCDU screen) MCDU - Multipurpose Control and Display Unit (this is the actual box used to enter data into the FMGC, you getting all this?) MMR Multi Mode Receiver, the GPS receiver for the GNADIRS, two are installed ND - Navigation Display (has all those nice little pictures on it to let you know where you are) N/W Nose Wheel 130 22/05/12
Fraud
PF Pilot Flying, the person actually handling the control or autopilot input. Also the person to blame for the bad landing. PFD - Primary Flight Display (the display you will look at the most, has airspeed, altitude, attitude, heading and more) PH Pilots Handbook PNF Pilot Non Flying, the non-flying pilot, used to be called PNF (Pilot Not Flying). A politically correct way to say this guy is just a professional critic, dont blame him for the landing. PTU Power Transfer Unit, pump that is able to transfer power (but not fluid) between the green and yellow hydraulic systems QRH Quick Reference Handbook RAT - Ram Air Turbine, an air driven backup pump for blue hydraulic RMP - Radio Management Panel, allows pilot to select which radio to tune or transmit on. SD - System Display, lower display for aircraft systems. SDAC - System Data Acquisition Concentrator SEC - Spoiler Elevator Computer SFCC - Slat/Flap Control Computer SRS - Speed Reference System THS - Trimmable Horizontal Stabilizer (did you guess it?) TLA - Thrust Lever Angle, the TLA indicator is a white donut on the N1 gauge. TOGA Takeoff Go Around. Highest selectable thrust level. Selected by putting thrust levers in TOGA detent. Also a mode for the Flight Director. TRU - Transformer Rectifier Unit, also known as TR, transformer rectifier UTC - Universal Coordinated Time (a politically correct way to say Zulu or GMT) VFTO Final Takeoff Speed, normally called Green Dot, best lift / drag WHC Window Heat Computer WTB Wing Tip Brake XFR - Transfer ZFCG - Zero Fuel Center of Gravity 131 22/05/12
Fraud
ZFW Zero Fuel Weight These are just my short list of favorites and there are many others but for the most part these should get you by. Bonus what persons names are on the Airbus instrument panels? Answer Max, Norm, Rose, Agent 1 & Agent 2, Rat Man Extra Bonus How do Airbus pilots celebrate their first line trip? Answer they have a TOGA party. I know, bad one
132
22/05/12
Fraud
COMPANY STUFF
Minimum F/A staffing Standard Complement A319 A320 A321 3 3 4 Minimum for flight (including boarding / deplaning) 3 3 4 Through flights with passengers onboard 1 1 2
Fuel
Captain may increase GATE RELEASE fuel as needed. Relay new fuel amount to dispatcher. Dispatch will check new fuel amount for load problems then contact departure station. If fuel decrease is needed then dispatch must agree. Note: Do not takeoff with less than T.O. MIN Fuel When refueling with passengers on board a flight attendant must be stationed at main door and jetway or stairs must be attached to aircraft Loading Last Minute Baggage Right engine must be shut down. Load forward compartment only.
133
22/05/12
Fraud
Taxiing
The captain is NOT required to stop only because a passenger leaves seat during taxi. Use judgment to determine if stopping will create a greater possible hazard. When able stop and re-seat passenger.
Standard pattern right hand turns Non-Standard pattern left hand turns
LOGBOOK STUFF
Ensure that yellow page has been removed for any item signed off by mechanic. White page stays in logbook. Full power takeoffs must be logged every 30 days or 150 takeoffs. The pilot will be notified in the release paperwork if a maximum thrust takeoff is required by the phrase MAX THRUST DEMO REQUIRED. The result (successful, unsuccessful or not attempted) must be noted in the logbook. Pilot MUST make logbook entry for MEL items if FR is noted for Follow up Required. If M notation then Maintenance will complete required actions and if O notation flight crew will complete required Operational items. ADIRS accuracy this check is done by Captain on every Parking Checklist, to be done within two minutes of aircraft stop. Use chart to determine acceptable limits. OK if 5 miles and 15 knots or less in all cases. Use Data Key, Position Monitor to determine NAV accuracy. If ground speed on NDs & IRU 3 TK/GS exceeds 15 knots, enter logbook entry for maintenance to track and verify, if exceeds 21 knots enter logbook entry for IRU removal. Hot Brakes Maintenance action is required if there is: 150 C difference in brake temps on the same strut and one brake 600 or greater or 60 or less a mean 200 C difference between different trucks fuse plug melted brake temp exceeds 900 C (800 - A321) Any higher inspection will take the place of a Daily check.
134
22/05/12
Fraud
Line Fixes
NOTE: on ground Flight Crew can reset any computer EXCEPT: ECU (engine control unit), EIU (engine interface unit) while engine running. BSCU (Brake Steering Control Unit) while taxiing, set parking brake first To reset CB in air check chart listed
135
22/05/12
Fraud
No Water Pressure If water has been serviced and there is no water pressure on ground (with APU bleed on) then check the F/A CIDS panel. If red SYSTEM INOP light is on then press the WTR SYSTEM DEPRE button. No data showing on RADNAV page (after GNADIRS is aligned) Make sure that the STBY NAV guarded NAV pb is not on (green light off). ANTI ICE Windshield (or Window) amber FAULT when on ground may be caused by heating of window by sun. Ensure all sun screens are stowed and cool cockpit. Then reset the WHC (Window Heat Computer) using CB# X13 for Capt. and CB# W13 for F/O. See Chap. 21 for details. If PED lights in passenger seats in cabin are red this shows that the powerport plugs for laptops are not powered. On the F/A panel across from forward F/A jumpseat above the video player there is a PED POWER p/b in the upper left hand corner near ceiling. When on this p/b should light up ON. Sometimes this p/b may have a burnt out bulb in it and not light properly. Press this p/b and see if lights change to green.
136
22/05/12