As 2162.1-1996 Verification and Use of Volumetric Apparatus General - Volumetric Glassware
As 2162.1-1996 Verification and Use of Volumetric Apparatus General - Volumetric Glassware
1—1996
Australian Standard
This is a free 6 page sample. Access the full version at http://infostore.saiglobal.com.
Part 1: General—Volumetric
glassware
This Australian Standard was prepared by Committee CH/1, Laboratory Glassware and
Related Apparatus. It was approved on behalf of the Council of Standards Australia
on 31 January 1996 and published on 5 May 1996.
Review of Australi an Standards. To keep abreast of progress in industry, Australi an Standards are subject
to periodic review and are kept up to date by the issue of amendments or new edit ions as necessary. It is
important therefore that Standards users ensure that they are in possession of the latest edit ion, and any
amendments thereto.
Full details of all Australi an Standards and related publi cati ons will be found in the Standards Australia
Catalogue of Publications; this information is supplemented each month by the magazine ‘The Australi an
Standard’, which subscribing members receive, and which gives detail s of new publications, new edit ions
and amendments, and of withdrawn Standards.
Suggesti ons for improvements to Australi an Standards, addressed to the head off ice of Standards Australi a,
are welcomed. Notificati on of any inaccuracy or ambiguity found in an Australi an Standard should be made
without delay in order that the matt er may be investigated and appropriate acti on taken.
Australian Standard
This is a free 6 page sample. Access the full version at http://infostore.saiglobal.com.
Part 1: General—Volumetric
glassware
PREFACE
This Standard was prepared by the Standards Australia Committee CH/1 on Laboratory
Glassware and Related Apparatus to revise the 1979 edition of AS 2162, Code of practice
for the use of volumetric glassware, which it now supersedes.
The objective of this Standard is to describe procedures for the verification of volumetric
glassware using water or mercury as the working substance, and give recommended
practices for the use of such glassware. The Standard was originally published in 1949 to
assist persons engaged in the manufacture, verification and use of volumetric glassware.
Attention is drawn to the fact that the attainment of a high level of accuracy depends upon
the use of satisfactory techniques as well as that of matching the quality of the glassware
to the task on hand. In regard to the latter, it is recommended that the use of Class A
glassware be restricted to those operations which necessitate attainment of the highest
degree of accuracy.
The units of volume used in this code are the litre (L) and the millilitre (mL). In terms of
the SI units the litre is equivalent to 10−3m 3 (1 dm3) and the millilitre is equivalent to
This is a free 6 page sample. Access the full version at http://infostore.saiglobal.com.
10 −6m 3 (1 cm3).
This Standard is essentially the same as the previous edition but has been reformatted and
includes a new clause dealing with apparatus and material. Clauses considering factors
affecting accuracy have also been rewritten.
The terms ‘normative’ and ‘informative’ have been used in this Standard to define the
application of the appendix to which they apply. A ‘normative’ appendix is an integral part
of a Standard, whereas an ‘informative’ appendix is only for information and guidance.
CONTENTS
Page
1 SCOPE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2 REFERENCED DOCUMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3 DEFINITIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
4 APPARATUS AND MATERIALS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
5 FACTORS AFFECTING ACCURACY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
6 VERIFICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
7 THE USE OF VOLUMETRIC GLASSWARE . . . . . . . . . . . . . . . . . . . . . . . . . 14
APPENDICES
A CLEANING OF VOLUMETRIC GLASSWARE . . . . . . . . . . . . . . . . . . . . . . 17
This is a free 6 page sample. Access the full version at http://infostore.saiglobal.com.
Originated as AS CR1—1949.
Previous editi on AS 2162—1979.
Revised and redesignated AS 2162.1 — 1996.
AS 2162.1 — 1996 4
STANDARDS AUSTRALIA
Australian Standard
Verification and use of volumetric apparatus
Part 1: General— Volumetric glassware
1 SCOPE This Standard provides guidance for users wishing to verify or to calibrate their
own articles of volumetric glassware by means of water or mercury (when more appropriate)
and to enable them to obtain the best accuracy in use.
International Standards and product Standards issued by Standards Australia for individual
articles of glassware, include clauses on tolerances and the definition of capacity. These
describe in sufficient detail and without ambiguity the method of manipulation to define the
This is a free 6 page sample. Access the full version at http://infostore.saiglobal.com.
3 DEFINITIONS For the purpose of this Standard the definitions below apply.
3.1 Accuracy — A qualitative term describing the degree of closeness with which the
indications of an instrument approach the true values of the measurand.
3.2 Calibration —all the operations for the purpose of determining the values of the errors
of measuring instruments, material measures, and measurement standards (and, if necessary,
to determine other metrological properties, including influence quantities).
3.3 Capacity — the nominal volume of water (or mercury) contained, or delivered by an
article of volumetric glassware, at its reference temperature.
3.4 Error of measurement —The discrepancy between the result of the measurement and
the value of the measurand.
NOTES:
1 The value of the measurand is a comparison value and, according to the particular case, equal
to —
(a) the true value of the quantity (generally unknown);
(b) the accepted true value; or
(c) the arithmetic mean of the results of a series of measurements.
2 The discrepancy can be expressed as the difference between these two values, or as the quotient
of that difference and the value of the measurand.
3.5 Measurand — A physical quantity, property or condition which is measured.
NOTE: The term ‘measurand’ is preferred to ‘quantity measured’, ‘measured quantity’ and ‘quantity
to be measured’.
COPYRIGHT
This is a free preview. Purchase the entire publication at the link below: