RSP - Lecture 8
RSP - Lecture 8
Introduction
Most commonly hybrid
oxidizer is injected into a precombustion or vaporization chamber upstream of the primary fuel grain. The fuel grain contains numerous axial combustion ports that generate fuel vapor to react with the injected oxidizer. An aft mixing chamber is employed to ensure that all fuel and oxidizer are burned before exiting the nozzle. 2
Introduction (2)
Advantages: Safety during fabrication, storage, or operation without possibility of explosion or detonation. Start-stop-restart capability Relatively low system cost Higher specific impulse than solid motors and higher densityspecific impulse than liquid engines The ability to smoothly change motor thrust over a wide range on demand. Disadvantages: Mixture ratio, thus specific impulse will vary somewhat during steady-state operation and throttling. Lower density-specific impulse than solid propellant systems Some fuel sliver must be retained in combustion chamber at end-of-burn Unproven propulsion system feasibility at large scale
3
lower fuel regression rates than solid motors and thus practical high-thrust hybrid motors should have multiple perforations in the fuel grain. The performance (in terms of specific impulse) of a hybrid depends very highly on the degree of flow mixing in the combustion chamber.
High performance depends on high combustion efficiency which again
is dependent on the thoroughness with which unburned oxidizer is mixed with unburned fuel from within sub-layers of the fuel boundary layer. Multiple combustion ports help achieve high combustion efficiency because of the turbulent mixing environment for unreacted fuel and oxidizer in the mixing chamber down stream of the fuel grain.
4
The desired thrust level Acceptable shifts in mixture ratio during burn Motor length and diameter constraints and, Desired oxidizer mass velocity.
thrust level and a propellant system. Then, the selection of the desired operating oxidizer-to-fuel mixture ratio (O/F ratio) determines the propellant characteristic velocity. Once the characteristic velocity and mixture ratio are identified,
the total propellant flow rate and thus the split between oxidizer and fuel flow rates necessary to
can be computed.
5
comb. port divided by the port cross-section area. Thus the fuel flow rate is linked with the oxidizer flow rate and cannot be separately calculated like in a liquid engine.
chamber pressure.
Thus the motor thrust is predetermined by the initial
propellant grain surface area and grain geometrical characteristics. Throttling or extinguishment is very difficult to achieve in practical solid rocket motor configurations since the fuel and oxidizer cannot be separated.
before combustion can occur. Thus the fuel surface regression is inherently related to the coupling of
Combustion port aerodynamics and Heat transfer to the fuel grain surface.
7
been shown to be limited to a relatively narrow flame zone occurring within the fuel grain boundary layer. The factors affecting the development of the fuel grain boundary layer and, hence, fuel regression characteristics include
Pressure Gas temperature Grain composition Combustion port oxidizer mass flow rate Combustion port length
The heat transfer relations between the gas and solid phase depend
heat transfer processes to non-metalized fuel grains With metalized fuel grains, radiation from the metal oxide particle cloud in the combustion port contributes a major portion of the total heat flux to the fuel grain.
8
to the general turbulence level of the combustion port gas flow. Localized combustion gas eddies or recirculation zones adjacent to the fuel surface act to significantly enhance the regression rate in these areas. The regression rate is considered to be insensitive to fuel grain bulk temperatures over the range in which solid rocket motors may operate (-65F to 165 F).
This is due to the absence of heterogeneous fuel/oxidizer
reactions at the fuel surface And because over this temperature range, the change in heat content of the solid fuel is small compared to the heat necessary to initiate vaporization of the fuel surface.
9
impact on the grain regression rate, which is largely a function of the energy required to convert the fuel from solid to vapor phase
This energy is called heat of gasification or vaporization
produce higher regression rates. In metallized fuels, the addition of ultra-fine aluminium (UFAl) powder (particle sizes on the order of 0.05 m to 0.1 m) to HTPB has been noted to significantly increase the fuel regression rate relative to pure HTPB.
Hybrid propellants containing Al particles with diameters
10
model of the hybrid combustion process for a non-metalized (nonradiating) fuel system.
Fuel is vaporized as a result
of heat transferred from the flame zone to the fuel mass. Vaporized fuel is convected upward toward the flame zone while oxidizer from the free stream is transported to the flame zone by diffusion and flow turbulence. The flame is established at a location within the boundary layer determined by the stoichiometric conditions under which combustion can occur. The thickness of the flame is determined primarily by the rate at which 11 the oxidation reaction occurs.