Engineering Drawing
Engineering Drawing
Engineering Drawing
CIPET GUWAHATI
UNIT 1
Letter writing
LETTERING
Writing of tittles, dimensions, scale, notes and other important particulars on a drawing is called Lettering. In other words to write any thing on drawing sheet in a simple and systematic way is known as Lettering. Lettering should, therefore, be done properly in clear, legible and uniform style. It should be in plain and simple style so that it could be done freehand and speedily.
The main requirements of lettering, namely, types and sizes of letters and technique of lettering are specified in IS:9609 -1983(Lettering for Technical Drawing), adopted from ISO:3098/11974(E).
ESSENTIAL FEATURES
Legibility Uniformity
TYPES OF LETTER
Single stroke letter
Inclined
TYPES
1.Vertical letters
The axis of letters and numerical is perpendicular to the horizontal axis is called vertical letters.
90
EXAMPLE
TYPES
2.Inclined letters When the axis of the letters are inclined at 75 to the horizontal axis is known as inclined letters. 75
EXAMPLE
EXAMPLE
TYPES
Gothic letters If we give more thickness to the single stork letters then it will be gothic letters. These are generally used for giving main titles. The out lines of the letters are first drawn with the aid of instruments and then filled in with ink. The thickness of the stem may vary from 1/5 to1/10 of the height of the letters.
EXAMPLE
NOTES
1.Vertical letters are preferable for execution. 2.Alaways draw guide(2h pencil) and do the lettering (HB pencil) between them.
3.Spacing between two letters should be approximately equal to 1/5th of the height of the letters. The letters should be so spaced that, by eye judgment, they do not appear too close together or too much apart.
4.Space between two words should be approximately equal to 3/5th of the height of the letters.
SIZES OF LETTERING
The size of a letter is described by its height. According to the height of letters, they are classified as: i) Lettering A ii) Lettering B In lettering A type, the height of the capital letter is divided into 14 parts, while in lettering B type it is divided into 10 parts.
The height of the letters and numerical for engineering drawing can be selected from 2.5, 3.5, 5, 7, 10, 14 and 20mm according to the size of drawing. The ratio of height to width varies but in case of most of the letters it is 6:5 The main titles are generally written in 6mm to 8mm size, sub-titles in 3mm to 6mm size, while notes, dimensions figures etc. in 3mm to 5mm size.
The drawing number in the title block is written in numerical of 10mm to 12mm size.
LETTERING A
LETTERING B
PLANE GEOMETRY
Where the construction of the geometrical shapes having only two dimensional that is called plane geometry.
A.
SQUARE: Equal sides, adjacent sides perpendicular RECTANGLE: Opposite sides equal , adjacent sides perpendicular RHOMBUS: Equal sides, opposite sides parallel but adjacent sides not perpendicular. RHOMBOID: Opposite sides parallel, adjacent sides not equal. TRAPEZOID: Two sides parallel TRAPEZIUM: No sides parallel
B.
C.
D.
E.
F.
POLYGONS
A plane figure bounded by straight lines are called a polygon. If the polygon has equals sides and angles, it is termed a regular polygon. A regular polygon can be inscribed in or circumscribed in a circle. The regular Polygons include---1.Pentagon----- 5sides 2.Hexagon------ 6sides 3.Heptagon ----- 7sides 4. Octagon ----- 8sides 5.Nonagon ------ 9sides 6.Decagon ------ 10sides 7 .Dodecagon -----12sides
GEOMETRICAL CONSTRUCTION
Geometrical construction are described as under following. 1.Bisecting a line. 2.To draw perpendiculars. 3.To draw parallel lines. 4.To divide a line. 5.To bisect an angle. 6.To trisect an angle. 7.To find the centre of an arc.
8. To construct an equilateral triangles. 9. To construct squares. 10.To construct regular polygons. 11. Special methods of drawing regular polygons. 12. Regular polygons inscribed in circle. 13. To draw regular figures using T-square and set-square.
14. To draw tangents. 15. Lengths of arcs. 16. circles and lines. 17. Inscribed circle.
Let it required to bisect the line PQ shown in fig. with P as center and any length greater than half PQ as radius, draw arcs on both sides of PQ. With Q as center and with the same radius, draw arcs to cut the previously drawn arcs at R and S. Join R and S. Let this line RS cut PQ at T. Then PT=TQ=1/2PQ. The line RS is the perpendicular bisector of PQ.
SOLID GEOMETRY
Geometry as used by the engineers for the graphics representation of solid of three dimensions on plane surfaces of two dimensions are called solid geometry.
WHAT IS SOLID
A SOLID IS THREE DIMENSIONAL OBJECT HAVING LENGTH, BREATH AND THICKNESS.IT IS BOUNDED BY PLANE FACES OR CURVED SURFACE OR COMBITION OF PLANE AND CURVED AREAS.
TYPES OF SOLID
1. Polyhedra 2.Solid of Revolution. Polyhedra: A polyhedron is defined as a solid bounded by planes called faces. When all the faces are equal and regular. This polyhedron is said to be regular polyhedra.
TYPES OF POLYHEDRA
A) Tetrahedron:-It is having four equal faces. All faces are equilateral triangle.
TETRAHYDRON
````````````````````````````````````````` `````````````CUBE OR HEXAHEDRON ````````````````````````````````````````` ``````````````````````````` It is having six faces ,all faces are equal squares.
OCTAHEDRON
DODECAHEDRON
ISOSAHEDRON
PRISM
Prism is a polyhedron having two equal and and similar faces known as its faces or bases
PYRAMID
A pyramid is a polyhedron consisting of a plane figure as its base and a number of lateral faces of triangular shape. All the triangle meet at a common point called the vertex or apex. Pyramid is named by according to its base.
SOLID OF REVOLUTION
There are following types of solid of revolution. (a)Cylinder: A right circular cylinder is a solid generated by the revolution of a rectangle about one of its sides which remain fixed. It has two equal circular bases. The perpendicular line joining the centers of the bases is its axis.
(B) CONE
Cone : A right circular cone is a solid generated by the revolution of a right angled triangle about one of its perpendicular sides which fixed. It has one circular base. Its axis joins the apex with the centre of the base. Straight lines drawn from the apex to the circumference of the base circle are all equal and are called generator of cone. The length of generator is the slant height of the cone.
(C) SPHERE
When a semi circle is rotated about its diameter as axis ,thus obtained solid is know as sphere.Mid point of the diameter is centre of a sphere .All points on surface of sphere are equidistant from its centre
(D) FRUSTUM
When a pyramid or a cone is cut by a plane parallel to its base and removing the top portion ,thus remaining is known as frustum.
(E) TRUNCATED
When a solid is cut by a plane inclined to the its base ,thus obtained solid is known as truncated solid .
PROJECTION
THE FIGURE AND VIEW FORMED BY JOINING, IN CORRECT SEQUENCE,THE POINT AT WHICH THESE LINES MEET THE PLANE IS CALLED THE PROJECTION OF OBJECT. THE SHADOW OR IMAGE OF AN OBJECT OBTAINED ON A PEICE OF PAPER IS KNOWN AS PROJECTION.
THEORY OF PROJECTION
PROJECTORS
The lines or rays drawn from the object to the plane are called projectors
TYPES OF PROJECTION
1. PICTORIAL PROJECTION
> PRESPECTIVE PROJECTION > OBLIQUE PROJECTION > ISOMETRIC PROJECTION 2. ORTHOGRAPHIC PROJECTION
PICTORIAL PROJECTION
THE PROJECTION IN WHICH THE DESCRIPTION OF THE OBJECT IS COMPLETELY UNDERSTOOD IN ONE VIEWIS KNOWN AS PICTORIAL PROJECTION. THE PROJECTION IN WHICH SHOW THE LENGTH,BREATH AND HEIGHT OF AN OBJECT IS KNOWN AS PICTORIAL PROJECTION.
TYPES
PERSPECTIVE PROJECTION
THIS IS THE TYPE OF PICTORIAL PROJECTIONIN WHICH ALL THE PROJECTORS MEET AT A POINT IS KNOWN AS PERSPECTIVE PROJECTION.THIS PROJECTION DOES NOT RE-PERSENT ACTUAL SIZE OF THE OBJECT BY GIVEN GENERAL OUT LOOK.
OBLIQUE PROJECTION
THIS IS THE TYPE OF PICTORIAL PROJECTION-IN WHICH ONE FACE OF THE OBJECT IS PARALLEL TO THE PLANE AND THE OTHER FACE IN INCLINED AT AN ANGLE OF 45 TO THE PLAIN OF PROJECTION IS KNOWN AS OBLIQUE PROJECTION.
EXAMPLE
ISOMETRIC PROJECTION
THIS IS THE TYPE OF PICTORIAL PROJECTION IN WHICH THE PROJECTOR ARE PARELL BUT INCLIEND AT AN ANGLE OF 30 TO THE PLANE IS KNOWN AS ISOMETRIC PROJECTION. NOTES ISOMETRIC PROJECTION GIVES TRUE SHAPE OF THE OBJECT, WHILE PERSPECTIVE PROJECTION AND OBLICQUE PROJECTIONS DO NOT.
EXAMPLE
ORTHOGRAPHICS PROJECTION
ORTHO MEANS RIGHT ANGLE & ORTHOGRAPHIC MEANS RIGHT ANGLED DRAWING.WHEN THE PROJECTORS ARE PERPENDICULAR TO THE PLANE ON WHICH THE PROJECTION IS OBTAINED. IT IS KNOWN AS ORTHOGRPHIC PROJECTION.
IT IS THE METHOD OF REPRESENTING THE EXACT SHAPE OF AN OBJECT IN TWO OR MORE VIEWS ON A PLANE .
EXAMPLE
PLANE
A PLANE IS A TWO DIMENTIONAL SURFACE , AREA OR OBJECT, HAVING ONLY LENGTH AND BREATH.
REFERENCE PLANE
2. In 2nd quad above H.P, behind V.P. 3. In 3rd quad below H.P. behind V.P. 4. In 4th quad- below H.P infront V.P. Where H.P-Horizontal plane
V.P-Vertical plane
PROJECTION
There are two method of projection. (1) First angle projection (2) Third angle projection.
DIFFERENCE
SYMBOLS
TYPES OF VIWES
ISOMETRIC VIWES:
SECTIONAL VIEW
Cutting plane or section plane: The imaginary plane which assumed to cut the object as required is called cutting plane or section plane. Cutting plane are generally shows by their traces by using lines made of alternate long and short dashes , thickened at the ends, bends and changes of direction and thin elsewhere.
SECTION
The surface produced when a section plane cuts a solid is termed as a section. It is indicate by continuous thin line inclined at 45 to the axis or to the main outline of the section. Spacing between these hatching lines is uniform and should be chosen in proportion to the size of the hatched section.
SECTIONAL VIEW:
The drawing showing that part of the object which is between the plane of projection and the section plane is called a sectional view. it may be a sectional top view or sectional front view. While drawing the sectional view, the portion of the object between the cutting plane and observer is assumed to removed and remaining portion is projected .thus, a section top view or sectional front view will show cut surface and all other part of the object beyond the cutting plane .
(I) section planes perpendicular to H.P and Parallel or inclined to the V.P (II) section planes perpendicular to V.P and Parallel or inclined to the H.P (III) Both planes are perpendicular to the H.P and V.P
when an object is symmetrical, it may be assumed to cut by two cutting planes at right to each other and containing the two centre lines of the object. the one quarter of the object between the planes is then removed showing only a half section. the projected view is a half sectional view.
REVOLVED SECTION:
A section is formed by passing a cutting plane at right angles to the axis of the object. it is in fact the cross-section of the object. This section is then revolved and brought into the plane of the axis and shown in the view in which the axis is seen as a line. Section shown in this manner is called a revolved section. the outline of the section is shown by a continuous line.
REMOVED SECTION:This section is obtained in the same manner as the revolved section, but is drawn outside the view, generally around the extension of the cutting-plane line. When it is not convenient to show the section in this manner, it identified by drawn away from its location. This method is generally used when the section is to be shown on an enlarged scale the purpose of dimensioning..
To show more details the cutting plane may be offset ,thus obtained section is known as offset section. section lines is the sectional view are similarly spaced but are offset along the dividing line between the sections. the position of the offset plane is always shown by a cutting-plane line in the view in which it is seen edge-wise.