ZXSDR NodeB Data Configuration

ZTE University
Content

Overview
NodeB Configuration
Ground Resource Configuration
Transmission Resource Configuration
Wireless Resource Configuration
Overview--LMT Data Configuration Mode
 On-line configuration
 This mode is to configure the ZDB of the B8200 directly. The data configured
on the line take effect immediately. To configure on the line, modify the
contents in the C:\ump file first, to set the IP address as the IP address of the
debugging network interface on the CC board of the B8200. Then, run the
LMT. The CC board is defaulted before delivery.
 Off-line configuration
 This mode is to modify the configurations on the client. The configurations are
saved into the designated directory in the mode of the XML file. In the off-line
configuration, the LMT is not connected to the B8200 and the operation does
not affect the running of the B8200. The off-line configuration mode is used
when there is no ump file under the root directory of the Disc C. One local
configuration file is required for the off-line configuration.
Overview--Iub Interface Protocol Stack （ IPO
E）
Radio Network Transport User Plane
Control Plane Network
Control Plane

Node B

PCH FP
RACH FP
FACH FP

DSCH FP
USCH FP
CPCH FP
Radio

DCH FP
Application Part
Network (NBAP)
Layer

Transport
SCTP UDP
Layer
IP IP

Data Link Data Link

Physical Layer
Overview--LMT Data Configuration Flow
Prepare
 IP Over FE Transmission
resource
configuration
Mode Trans Plan
parameters for
mission Dat RNC
interconnection Ethern Globe
IP
Static
SCTP
SCTP IP
BFD OMCB

a Configura
et port route stream Clock
param para param param
parame Para param param param
eter meter eter eter
ter meter ete eter eter

tion Flow :
NodeB
Configuration

Rack Wireless resource

NodeB clock configuration
and
basic referen
board
attribut ce
configu
es source
ration

RRU
RF Base
Common WCDMA Local
Connec Band
Ground resource tion
Paramet
Resour
Sector Cell
er
configuration ce Pool

Topolo
Enviro Serial Dry
gy
nment port contact
structur
monito config
e
configu End
ring uration ration
setting
Content

LMT Data Configuration

NodeB Configuration
Ground Resource Configuration
Transmission Resource Configuration
Wireless Resource Configuration
NodeB Configuration
 NodeB Basic Attributes
 Clock Reference Source
 Configuring Rack and Board
NodeB Configuration
 Setting NodeB Basic Attributes :Basic Parameter an
d Other Relevant Parameters
NodeB Configuration
NodeB Configuration
NodeB Configuration
 Configuring Rack and Board : Create RRU rack
NodeB Configuration
 Configuring Rack and Board : Create board on BBU
and RRU rack
NodeB Configuration
 Configuring Rack and Board : Create board on BBU
and RRU rack
NodeB Configuration
 Configuring Clock Reference Source : Right-click and choose
Configuration Management  BS  Configure Clock Referenc
e Source. Configure Clock Reference Source dialog box pops
up.
Content

LMT Data Configuration

NodeB Configuration
Ground Resource Configuration
Transmission Resource Configuration
Wireless Resource Configuration
Ground Resource Configuration
 Environment Monitoring
 In-line Tower Amplifier
 Serial Port
 Topology structure
 AISG Device
 Dry Contact
Ground Resource Configuration
 Configuring Environment Monitoring: click Configuration Mana
gement→ Ground Resource Management→ Environment Moni
toring to open the Environment Monitoring window:
Ground Resource Configuration
 Configuring Topology Structure: Click Configuration
Management→ Ground Resource Management→ T
opology to open the Topology window.
Ground Resource Configuration
 Configuring Topology Structure:

 About upper-level and lower-level in the topology configuration:

 The board/rack near the baseband processing unit is the upper-level
 The board/rack away from the baseband processing unit is lower-level.
Ground Resource Configuration
 Configuring Dry Contact
Content

LMT Data Configuration

NodeB Configuration
Ground Resource Configuration
Transmission Resource Configuration
Wireless Resource Configuration
Transmission Resource Configuration
 For the IP over FE transmission, the following nine it
ems should be configured:
 Ethernet Parameter
 Global Port Parameter
 IP Parameter
 Static Route Parameter
 SCTP Parameter
 SCTP Stream Parameter
 IP Clock Parameter
 BFD Parameter
 OMC-B Parameter
Transmission Resource Configuration
 Configuring Ethernet Parameter--Click Physical Media Configu
ration→ Ethernet parameter .Right-click the blank part in this p
ane and choose Add to open the Ethernet parameter manage
ment dialog box:
Transmission Resource Configuration
 Configuring Global Port Parameter--Click Transmission Resource Management
→ IP Bearing Configuration→ Global port parameter to open the Global port pa
rameter pane. Right-click the blank part in this pane and choose Add to open t
he Global Port Parameter dialog box:
Transmission Resource Configuration
 Configuring IP Parameter--Click Transmission Resource Management→ IP Be
aring Configuration→ IP parameter to open the IP parameter pane. Right-click t
he blank part in this pane and choose Add to open the IP Parameter Managem
ent dialog box:
Transmission Resource Configuration
 Configuring Static Route Parameter--Click Transmission Resource Manageme
nt→ IP Bearing Configuration→ Static Router Parameter. Right-click the blank
part in the right pane and choose Add to open the Static route configuration dia
log box.
Transmission Resource Configuration
 Configuring SCTP Parameter--Click Transmission Resource Management→ IP
Bearing Configuration→ SCTP Parameter to open the SCTP parameter pane.
Right-click the blank part in this pane and choose Add to open the SCTP para
meter management dialog box:
Transmission Resource Configuration
 Configuring SCTP Stream Parameter--Click Transmission Res
ource Management→ IP Bearing Configuration→ SCTP Strea
m Parameter to open the SCTP stream parameter pane. Right-
click the blank part in this pane and choose Add to open the S
CTP stream parameter management dialog box.
Transmission Resource Configuration
 Configuring IP Clock Parameter--Click Transmission Resource
Management→ IP Bearing Configuration→ IP Clock Parameter
to open the IP Clock parameter pane. Right-click the blank part
in this pane and choose Add to open the IP Clock parameter di
alog box.
Transmission Resource Configuration
 Configuring BFD Parameter--Click Transmission Resource Managem
ent→ IP Bearing Configuration→ BFD Parameter to open the BFD par
ameter pane. Right-click the blank part in this pane and choose Add to
open the BFD parameter dialog box.
Transmission Resource Configuration
 Configuring OMC-B Parameter
Content

LMT Data Configuration

NodeB Configuration
Ground Resource Configuration
Transmission Resource Configuration
Wireless Resource Configuration
Wireless Resource Configuration
 RF Connection
 RRU Common Parameter
 Base Band Resource Pool
 WCDMA Sector
 Local Cell
Wireless Resource Configuration
 Configuring RF Connection--Click Wireless Resource Management→
RF Connection to open the RF Connection pane. Right-click the blank
part in this pane and choose Add →Rack to open the RF Connection
dialog box.
Wireless Resource Configuration
 Configuring RRU Common Parameter --Click Wireless Resource Man
agement→ RRU Common Parameter to open the RRU Common Para
meter pane. Right-click the blank part in this pane and choose Add to
open the RRU Common Parameter dialog box.
Wireless Resource Configuration
 Configuring Baseband resource pool--Click Wireless
Resource Management→ Baseband Resource Pool
and right-click the blank part in this pane and choose
Add to open the baseband resource pool Manageme
nt dialog box:
Wireless Resource Configuration
 Configuring Baseband resource--Click Baseband Resource Po
ol→ Baseband Resource to open the Baseband Resource pan
e. Right-click the blank part in this pane and choose Add to op
en the Baseband Resource dialog box:
Wireless Resource Configuration
 Configuring WCDMA Sector--Click Wireless Resource Manage
ment→ WCDMA Sector to open the WCDMA Sector pane. Rig
ht-click the blank part in this pane and choose Add to open the
WCDMA Sector dialog box:
Wireless Resource Configuration
 Configuring Local cell--Click Wireless Resource Management
→ WCDMA Sector to open the WCDMA Sector pane. Right-cli
ck the blank part in this pane and choose Add Local Cell to ope
n the Local Cell Management dialog box:
Wireless Resource Configuration
 Configuring Local cell
Wireless Resource Configuration
 Configuring Local cell