MMBB NSB
MMBB NSB
Quick guide
MMBB new site build
● As we are starting to receive MMBB scope on the day shift, I made this guide of
the most important things you can check to ensure you do a well integration
● If something is not clear let me know and don´t forget to check with your lead if
you have issues
Summarize
● Last configuration for NR600 was L700/L600 on legacy BB and NR600 on the
5G BB
● As 5G BB hadn´t GPS we defined the NGS (node group sync) to pass the GPS
signal from Legacy BB through the radio 4449 to the 5G BB
4449
● Data 2
● Data 1
● L700
● NR600
● L600
● NGS
● Legacy BB LTE ● 5G BB (BB6630)
Summarize
● On this new configuration we will have L700/L600 on the new 5G BB
● If L700 is already prexisting on the legacy BB, at the end we will move it to the MMBB
● There is no NGS here, instead you Will have the GPS signal on MMBB through a spliter or an
IXR router
● On site Fe still use to connect the data 1 on the legacy BB but is not used any more, all
L700/L600 and Nr600 share the same fiber that go to data2 on the MMBB (ports A for Alpha, B
for beta, C for gamma)
This is good by FEs, because in case of a rollback
you could request radio swap scripts for
4449 ● L700
4449 to let L700 enabled on the legacy BB
● Data 2 ● L600
● NR600
● ECI files are starting to be used, but you still may need to use SIF in case they are
not avaiable
● In case you use SIF
After having connectivity you can run all this scripts on MMBB, but the ones in yellow Will fail
until the cells are enabled on the MMBB
● In case you use ECI
after the ASP load the ECI, enroll your node as usual and run the commands for URI alarm
The only two scripts that the ECI don´t run are the ones on yellow because the cells must
be enabled to run them
● Don´t forget to activate the supervisons on the ENM GUI
● As a suggestion in both cases (SIF or ECI) run this baselines after the integration
as the ones on the package are not usually updated
● netconf
/home/shared/EJAMBZD/Baseline/5G/01_CUCP_CUUP_DU_5Qi_tables-
PA1.xml
● run
/home/shared/EJAMBZD/Baseline/5G/02_NR600_Baseline_NSA_SA_RevY.m
os
● run
/home/shared/EJAMBZD/Baseline/LTE_NSB/Tmobile_01_L20Q2_baseline_B
BU_PA7.mos
● After FE confirms that the 4449 are installed
● Delete the rilinks on Legacy BB for the L700 radios, this is because the radios may get troubles to get enabled
on the MMBB if rilinks are up on legacy BB
Also run the HwSwap baseline
If rilinks on the MMBB are not created use the next script
confb+
gs+
lt all cr Equipment=1,RiLink=BB-01-C-6-03-Data2
#Create RiLink FieldReplaceableUnit=BB-01,RiPort=C
cr Equipment=1,RiLink=BB-01-A-6-01-Data2 FieldReplaceableUnit=6-03,RiPort=DATA_2
FieldReplaceableUnit=BB-01,RiPort=A fi
FieldReplaceableUnit=6-01,RiPort=DATA_2 gs-
confb-
cr Equipment=1,RiLink=BB-01-B-6-02-Data2
FieldReplaceableUnit=BB-01,RiPort=B
FieldReplaceableUnit=6-02,RiPort=DATA_2
● Run your scripts on LTE node,
the last one Will delete L700 on legacy node, as a suggestion run it before CT
as riot may get troubles to get on green for L700 if the cells are still on legacy
checks
get
Transport=1,Router=vr_TRAFFIC,RouteTa
bleIPv4Static=1,Dst=1,NextHop=1
address > $TRAFFICIP
mcc Transport=1,Router=vr_TRAFFIC
ping $TRAFFICIP
Don´t forget to check the usual KPIs (fiber levels, BIT error, VSWR, RSSI, delta,
cell availability and percentage of calls successful)
Clean up process
● Then you Will have all the nodes that has relations
with yours
● Create a .txt file with all the nodes list
● Finally execute the script with the command below, it Will run the script on all the nodes on the list
Just make sure all is ok
mobatch clean.txt 3TIS733A_E61_EXTERNALEUTRANCELLFDDDELETE_02_ExternalEUtranCellFDD_delete_cleanup.mos