Professional Documents
Culture Documents
Wellbore Instability Causes and Consequences
Wellbore Instability Causes and Consequences
248 Language/Jezik:English/Engleski
Vol. 19
str. 87 - 98
WELLBORE INSTABILITY: CAUSES AND CONSEQUENCES NESTABILNOST KANALA BUOTINE: UZROCI I POSLJEDICE
BORIVOJE PAI, NEDILJKA GAURINA-MEIMUREC, DAVORIN MATANOVI
University of Zagreb, Faculty of Mining, Geology and Petroleum Engineering, Pierottijeva 6, 10000 Zagreb, Croatia
Abstract Wellbore instability is one of the main problems that engineers meet during drilling. The causes of wellbore instability are often classified into either mechanical (for example, failure of the rock around the hole because of high stresses, low rock strength, or inappropriate drilling practice) or chemical effects which arise from damaging interaction between the rock, generally shale, and the drilling fluid. Often, field instances of instability are a result of a combination of both chemical and mechanical. This problem might cause serious complication in well and in some case can lead to expensive operational problems. The increasing demand for wellbore stability analyses during the planning stage of a field arise from economic considerations and the increasing use of deviated, extended reach and horizontal wells. This paper presents causes, indicators and diagnosing of wellbore instability as well as the wellbore stresses model.
Saetak Nestabilnost kanala buotine jedan je od glavnih problema s kojima se inenjeri susreu tijekom buenja. Nestabilnost kanala moe biti posljedica mehanikih uzroka (naprimjer, lom stijene oko kanala zbog velikih naprezanja, mala vrstoa stijene ili neodgovarajua praksa buenja) ili kemijskih uzroka (tetne reakcije izmeu stijene, obino ejla i isplake). U praksi je nestabilnost kanala buotine esto posljedica zajednikog djelovanja kemijskih i mehanikih mehanizama. Ovaj problem moe izazvati ozbiljne komplikacije u buotini i u nekim sluajevima moe dovesti do skupih operativnih problema. Poveana potreba za analizama nestabilnosti kanala buotine tijekom faze planiranja polja proizlazi iz ekonomskih razmatranja i rastue upotrebe otklonjenih, poveanog dosega i horizontalnih buotina. U radu se prikazuju uzroci i pokazatelji nestabilnosti kanala buotine, dijagnosticiranje problema te naprezanja u stijeni pribuotinske zone.
Introduction Unexpected or unknown behavior of rock is often the cause of drilling problems, resulting in an expensive loss of time, sometimes in a loss of part or even whole borehole. Borehole stability is a continuing problem which results in substantial yearly expenditures by the petroleum industry (Bradley, 1978, Awal et al., 2001). As result, a major concern of the drilling engineers is keeping the borehole wall from falling in or breaking down. Detailed attention is paid to drilling fluid programs, casing programs, and operating procedures in drilling a well to minimize these costly problems. Wellbore instability has become an increasing concern for horizontal and extended reach wells, especially with the move towards completely open hole lateral section,
and in some cases, open hole build-up section through shale cap rocks. More recent drilling innovations such as underbalanced drilling techniques, high pressure jet drilling, re-entry horizontal wells and multiple laterals from a single vertical or horizontal well often give rise to challenging wellbore stability question (Martins et al., 1999; Kristiansen, 2004; Tan et al., 2004). In many cases the section of an optimal strategy to prevent or mitigate the risk of wellbore collapse might compromise one or more of the other elements in the overall well design, e.g., drilling rate of penetration, the risk of differential sticking, hole cleaning ability, or formation damage. For drilling situations it is therefore desirable to apply integrated predictive methods that can, for instance, help to optimize the mud density, chemistry, rheology, the selection of filter cake building additives,
88
Rud.-geol.-naft. zb., Vol. 19, 2007. B. Pai, N. Gaurina-Meimurec, D. Matanovi: Wellbore instability: Causes and...
and possibly temperature. Sensitivity studies can also help assess if there is any additional risk due to the selected well trajectory and inclination. Wellbore stability predictive models may also be used to design appropriate completions for inflow problems where hole collapse and associated sand production, or even the complete loss of the well, may concerned. For example, in highly permeable and weakly cemented sandstones such predictive tools can be used to decide whether a slotted or perforated liner completion would be preferred over leaving a horizontal well completely open hole (McLellan at all,1994b).
Table 1 Causes of wellbore instability Tablica 1. Uzroci nastabilnosti kanala buotine
Causes of wellbore instability Wellbore instability is usually caused by a combination of factors which may be broadly classified as being either controllable or uncontrollable (natural) in origin. These factors are shown in Table 1 (McLellan et al., 1994a, Bowes and Procter , 1997; Chen et al., 1998; Mohiuddin et al., 2001).
Causes of Wellbore Instability Uncontrollable (Natural) Factors Naturally Fractured or Faulted Formations Tectonically Stressed Formations High In-situ Stresses Mobile Formations Unconsolidated Formations Naturally Over-Pressured Shale Collapse Induced Over-Pressured Shale Collapse Controllable Factors Bottom Hole Pressure (Mud Density) Well Inclination and Azimuth Transient Pore Pressures Physico/chemical Rock-Fluid Interaction Drill String Vibrations Erosion Temperature
Uncontrollable factors Naturally fractured or faulted formations A natural fracture system in the rock can often be found near faults. Rock near faults can be broken into large or small pieces. If they are loose they can fall into the wellbore and jam the string in the hole (Nguyen et al., 2007). Even if the pieces are bonded together, impacts from the BHA due to drill string vibrations can cause the formation to fall into the wellbore. This type of sticking is particularly unusual in that stuck pipe can occur while drilling. Figure 1 shows possible problems as result drilling a naturally fractured or faulted system. This mechanism can occur in tectonically active zones, in prognosed fractured limestone, and as the formation is drilled. Drill string vibration have to be minimized to help stabilize these formations (Bowes and Procter, 1997). Hole collapse problems may become quite severe if weak bedding planes intersect a wellbore at unfavorable angles. Such fractures in shales may provide a pathway for mud or fluid invasion that can lead to time-depended strength degradation, softening and ultimately to hole collapse. The relationship between hole size and the fracture spacing will be important in such formations.
Figure 1 Drilling through naturally fractured or faulted formations Slika 1. Buenje kroz prirodno raspucane ili rasjedima ispresjecane formacije
Tectonically Stressed Formations Wellbore instability is caused when highly stressed formations are drilled and if exists a significant difference between the near wellbore stress and the restraining pressure provided by the drilling fluid density. Tectonic
Rud.-geol.-naft. zb., Vol. 19, 2007. B. Pai, N. Gaurina-Meimurec, D. Matanovi: Wellbore instability: Causes and...
89
stresses build up in areas where rock is being compressed or stretched due movement of the earths crust. The rock in these areas is being buckled by the pressure of the moving tectonic plates. When a hole is drilled in an area of high tectonic stresses the rock around the wellbore will collapse into the wellbore and produce splintery cavings similar to those produced by over-pressured shale (Figure 2). In the tectonic stress case the hydrostatic pressure required to stabilize the wellbore may be much higher than the fracture pressure of the other exposed formations (Bowes and Procter, 1997). This mechanism usually occurs in or near mountainous regions. Planning to case off these formations as quickly as possible and maintaining adequate drilling fluid weight can help to stabilize these formations
the formation squeezing into the wellbore (Bowes and Procter, 1997). This mechanism normally occurs while drilling salt. An appropriate drilling fluid and maintaining sufficient drilling fluid weight are required to help stabilize these formations.
Figure 3 Drilling through mobile formations Slika 3. Buenje kroz pokretljive formacije
Unconsolidated formations An unconsolidated formation falls into the wellbore because it is loosely packed with little or no bonding between particles, pebbles or boulders. The collapse of formations is caused by removing the supporting rock as the well is drilled (Figure 4). It happens in a wellbore when little or no filter cake is present. The un-bonded formation (sand, gravel, etc.) cannot be supported by hydrostatic overbalance as the fluid simply flows into the formations. Sand or gravel then falls into the hole and packs off the drill string. The effect can be a gradual increase in drag over a number of meters, or can be sudden (Bowes and Procter, 1997). This mechanism is normally associated with shallow formation. An adequate filter cake is required to help stabilize these formations.
Figure 2 Drilling through tectonically stressed formations Slika 2. Buenje kroz tektonski napregnute formacije
High in-situ stresses Anomaliously height in-situ stresses, such as may be found in the vicinity of salt domes, near faults, or in the inner limbs of a folds may give rise to wellbore instability. Stress concentrations may also occur in particularly stiff rocks such as quartzose sandstones or conglomerates. Only a few case histories have been described in the literature for drilling problems caused by local stress concentrations, mainly because of the difficulty in measuring or estimating such in situ stresses. Mobile formations The mobile formation squeezes into the wellbore because it is being compressed by the overburden forces. Mobile formations behave in a plastic manner, deforming under pressure. The deformation results in a decrease in the wellbore size, causing problems of running BHAs, logging tools and casing (Figure 3). A deformation occurs because the mud weight is not sufficient to prevent
Figure 4 Drilling through unconsolidated formations Slika 4. Buenje kroz nekonsolidirane formacije
Rud.-geol.-naft. zb., Vol. 19, 2007. B. Pai, N. Gaurina-Meimurec, D. Matanovi: Wellbore instability: Causes and...
Naturally over-pressured shale is the one with a natural pore pressure greater than the normal hydrostatic pressure gradient. Naturally over-pressured shales are most commonly caused by geological phenomena such as under-compaction, naturally removed overburden and uplift (Figure 5). Using insufficient mud weight in these formations will cause the hole to become unstable and collapse (Bowes and Procter, 1997; Tan et al., 1997). This mechanism normally occurs in prognosed rapid depositional shale sequences. The short time hole exposure and an adequate drilling fluid weight can help to stabilize these formations.
Figure 6 Drilling through induced over-pressured shale Slika 6. Buenje kroz ejl pod izazvanim nadtlakom
Controllable factors Bottom hole pressure (mud density) Depending upon the application, either the bottom hole pressure, the mud density or the equivalent circulating density (ECD), is usually the most important determinant of whether an open wellbore is stable (Figures 7 and 8) (Hawks and McLellan, 1997; Gaurina-Meimurec, 1998). The supporting pressure offered by the static or dynamic fluid pressure during either drilling, stimulating, working over or producing of a well, will determine the stress concentration present in the near wellbore vicinity. Because rock failure is dependent on the effective stress the consequence for stability is highly dependent on whether and how rapidly fluid pressure penetrate the wellbore wall. That is not to say however, that high mud densities or bottom hole pressures are always optimal for avoiding instability in a given well. In the absence of an efficient filter cake, such as in fractured formations, a rise in a bottom hole pressure may be detrimental to stability and can compromise other criteria, e.g., formation damage, differential sticking risk, mud properties, or hydraulics (Tan and Willoughby, 1993; McLellan, 1994a; Mohiuddin et al., 2001).
Figure 5 Drilling through a naturally over-pressured shale Slika 5. Buenje kroz ejl pod prirodnim nadtlakom
Induced Over-Pressured Shale Collapse Induced over-pressured shale collapse occurs when the shale assumes the hydrostatic pressure of the wellbore fluids after a number of days exposures to that pressure. When this is followed by no increase or a reduction in hydrostatic pressure in the wellbore, the shale, which now has a higher internal pressure than the wellbore, collapses in a similar manner to naturally over-pressured shale (Figure 6) (Bowes and Procter, 1997). This mechanism normally occurs in water based drilling fluids, after a reduction in drilling fluid weight or after a long exposure time during which the drilling fluid was unchanged.
Rud.-geol.-naft. zb., Vol. 19, 2007. B. Pai, N. Gaurina-Meimurec, D. Matanovi: Wellbore instability: Causes and...
91
reduced by the swabbing action of the drill string for instance. If the formation has a sufficiently low tensile strength or is pre-fractured, the imbalance between the pore pressures in the rock and the wellbore can literally pull loose rock off the wall. Surge pressures can also cause rapid pore pressures increases in the near-wellbore area sometimes causing an immediate loss in rock strength which may ultimately lead to collapse. Other pore pressure penetration-related phenomena may help to initially stabilize wellbores, e.g. filter cake efficiency in permeable formations, capillary threshold pressures for oil-based muds and transient pore pressure penetration effects (McLellan, 1994a).
Figure 7 Effect of mud weight on the stress in wellbore wall Slika 7. Utjecaj gustoe isplake na naprezanja u kanalu buotine
Physical/chemical fluid-rock interaction There are many physical/chemical fluid-rock interaction phenomena which modify the near-wellbore rock strength or stress. These include hydration, osmotic pressures, swelling, rock softening and strength changes, and dispersion. The significance of these effects depend on a complex interaction of many factors including the nature of the formation (mineralogy, stiffness, strength, pore water composition, stress history, temperature), the presence of a filter cake or permeability barrier is present, the properties and chemical composition of the wellbore fluid, and the extent of any damage near the wellbore (McLellan, 1994a). Drillstring vibrations (during drilling) Drillstring vibrations can enlarge holes in some circumstances. Optimal bottomhole assembly (BHA) design with respect to the hole geometry, inclination, and formations to be drilled can sometimes eliminate this potential contribution to wellbore collapse. Some authors claim that hole erosion may be caused due to a too high annular circulating velocity. This may be most significant in a yielded formation, a naturally fractured formation, or an unconsolidated or soft, dispersive sediment. The problem may be difficult to diagnose and fix in an inclined or horizontal well where high circulating rates are often desirable to ensure adequate hole cleaning (McLellan, 1994a). Drilling fluid temperature Drilling fluid temperatures, and to some extent, bottomhole producing temperatures can give rise to thermal concentration or expansion stresses which may be detrimental to wellbore stability. The reduced mud temperature causes a reduction in the near-wellbore stress concentration, thus preventing the stresses in the rock from reaching their limiting strength (McLellan, 1994a).
Well Inclination and Azimuth Inclination and azimuthal orientation of a well with respect to the principal in-situ stresses can be an important factor affecting the risk of collapse and/or fracture breakdown occurring (Figure 8). This is particularly true for estimating the fracture breakdown pressure in tectonically stressed regions where there is strong stress anisotropy (McLellan, 1994a).
Figure 8 Effect of the well depth (a) and the hole inclination (b) on wellbore stability Slika 8. Utjecaj dubine (a) i otklona (b) na stabilnost kanala buotine
Transient wellbore pressures Transient wellbore pressures, such as swab and surge effects during drilling, may cause wellbore enlargement (Hawks and McLellan, 1997). Tensile spalling can occur when the wellbore pressure across an interval is rapidly
Rud.-geol.-naft. zb., Vol. 19, 2007. B. Pai, N. Gaurina-Meimurec, D. Matanovi: Wellbore instability: Causes and...
A list of the indicators of wellbore instability which are primarily caused by wellbore collapse or convergence during the drilling, completion or production of a well is shown in Table 2. They are classified in two groups: direct and indirect causes. Direct symptoms of instability include observations of overgauge or undergauge hole, as readily observed from caliper logs (Mohiuddin et al., 2001). Caving from the wellbore wall, circulated to surface, and
hole fill after tripping confirm that spalling processes are occurring in the wellbore. Large volumes of cuttings and/ or cavings, in excess of the volume of rock which would have been excavated in a gauge hole, similarly attest to hole enlargement. Provided the fracture gradient was not exceeded and vuggy or naturally fractured formations were not encountered, a requirement for a cement volume in excess of the calculated drilled hole volume is also a direct indication that enlargement has occurred (McLellan et al., 1994a).
Indicators of wellbore instability Direct indicators Oversize hole Undergauge hole Excessive volume of cuttings Excessive volume of cavings Cavings at surface Hole fill after tripping Excess cement volume required Indirect indicators High torque and drag (friction) Hanging up of drillstring, casing, or coiled tubing Increased circulating pressures Stuck pipe Excessive drillstring vibrations Drillstring failure Deviation control problems Inability to run logs Poor logging response Annular gas leakage due to poor cement job Keyhole seating Excessive doglegs
Diagnosing of wellbore instability mechanisms Diagnosing the four most important wellbore instability mechanisams is described in Figure 9. Three
of these are mechanical (breakouts, closely spaced natural fractures and weak planes, drilling induced fractures) and one of these is chemical (chemical activity) in origin.
Rud.-geol.-naft. zb., Vol. 19, 2007. B. Pai, N. Gaurina-Meimurec, D. Matanovi: Wellbore instability: Causes and...
93
Figure 9 Diagnosing the 4 most common wellbore instability mechanisms Slika 9. Dijagnostciranje etiri najea mehanizma nestabilnosti kanala
Wellbore stresses model development Before describing the variety of predictive models that are available for assessing wellbore stability it is necessary to define what constitutes the failure of a wellbore. Clearly, the spalling or erosion of manageable amounts of rock from a wellbore wall does not necessarily imply that the wellbore has failed. Providing that sufficient hydraulic power is available to circulate cavings out of the hole it cannot be claimed that hole enlargement, or convergence in many cases, has impaired the ability of the hole to serve its engineering function that is to gain access to subsurface hydrocarbons. It follows, therefore, that wall deformation and yielding phenomena do not necessarily mean that a wellbore has failed (McLellan, 1994a).
Figure 10 In-situ stresses Slika 10. In-situ naprezanja
94
Rud.-geol.-naft. zb., Vol. 19, 2007. B. Pai, N. Gaurina-Meimurec, D. Matanovi: Wellbore instability: Causes and...
Before a wellbore is drilled the rock is in a state of equilibrium. The stresses in the earth under these conditions are known as the far field stresses (v, H, h or in-situ stresses (Gaurina-Meimurec, 1994). When the well is drilled, the rock stresses in the vicinity of the wellbore are redistributed as the support originally offered by the drilled out rock is replaced by the hydraulic pressure of the mud. The stresses can be resolved into a vertical or overburden stress, v, and two horizontal stresses, H (the maximum horizontal in-situ stress), and h (the minimum horizontal in-situ stress), which are generally unequal (Figure 10) (McLean et al.,1990). If the redistributed stress state exceeds the rock strength, either in tension or compression, then instability may result. Figure 11 shows the wellbore stresses after drilling. These are described as radial stress r, tangential stress (circumferential or hoop stress) t , and axial stress a. The radial stress acts in all directions perpendicular to the wellbore wall, the tangential stress circles the borehole, and the axial stress acts parallel to the wellbore axis (McLean, 1990).
H
V
z
aw
x
x1
z iw r
Figure 12 The coordinate system for the in-situ stress display Slika 12. Koordinatni sustav za prikaz in-situ naprezanja
Local stresses induced by in-situ stress and hydraulic effects at the wellbore wall (r = rw), for vertical well can be described as follows:
The local stress distribution around a wellbore are controlled by mechanical (in-situ stresses), chemical, thermal, and hydraulic effects. The coordinate referencing system used to calculate the stress distribution around a wellbore, goverrned by the in-situ stress and hydraulic effects, is shown in Figure 12.
r = pw
(Eq.2)
Rud.-geol.-naft. zb., Vol. 19, 2007. B. Pai, N. Gaurina-Meimurec, D. Matanovi: Wellbore instability: Causes and...
95
Local Stresses at the wellbore wall (r = rw) induced by chemical and thermal effects can be expressed as follows (Eq.3):
r = 0 t = a = p ( 2 ) 1
stresses and/or strains around the wellbore. The computed stresses and strains must then be compared against a given failure criterion.
1 p ( 2 ) 1 1
(Eq.3)
Shear Failure Numerous shear failure criteria such as Mohr-Coulomb, Drucker-Prager, von Mises, modified Lade criteria and others are proposed in the literature (Simangunsong et al., 2006; Zhang et al, 2006; Maury et al., 1987; Morita et al., 1993; McLean et al., 1990). The Mohr-Coulomb shear-failure model is one of the most wiedely used models for evaluating borehole collapse. This model neglects the intermediate principal stress but includes the effect of directional strengths of shales. The shear-failure criterion can be expressed by the following (Eq.4):
From Equation 3, one notes that pore pressure and temperature profiles are needed to calculate the stress distribution around a wellbore arising from chemical and thermal effects. The pore pressure profile is altered by water and ion movements into or out of the shale due to hydraulic, chemical, and electical potentials. Pore pressure and temperature profiles can be obtained by using equations presented in literature (Ottesen and Kwakwa, 1991; Lomba et al, 2000; Awal et al., 2001; Zhang et al, 2006; Nguyen et al., 2007). In order to evaluate the potential for wellbore stability a realistic constitutive model must be used to compute the
p Pp ) Co + ( 3 p Pp ) tan 2
(Eq. 4)
Shear Stress magnitudes can be ordered in 6 different ways, as shown in Table 3 (Bowes and Procter, 1997).
Failure type
Figure
The failure will occure in the radial/axial plane because the maximum (a) and minimum (r) stresses are oriented in this plane (a vertical plane).
The failure will occure in the radial/tangential plane because the maximum (t) and minimum (r) stresses are oriented in this plane (the horizontal plane).
96
Table 3 Shear failure types (continued) Tablica 3. Tipovi sminog loma (nastavak)
Rud.-geol.-naft. zb., Vol. 19, 2007. B. Pai, N. Gaurina-Meimurec, D. Matanovi: Wellbore instability: Causes and...
Failure type
Geometry and Orientation The failure will occure in the axial/ tangential arc because the maximum (a) and minimum (t) stresses are oriented in this arc (the arc of the borehole wall).
Figure
The failure will occure in the radial/tangential plane because the maximum (r) and minimum (t) stresses are oriented in this plane (the horizontal plane).
The failure will occure in the radial/ axial plane because the maximum (r) and minimum (a) stresses are oriented in this plane (a vertical plane).
The failure will occure in the axial/ tangential arc because the maximum (t) and minimum (a) stresses are oriented in this arc (the arc of the borehole wall).
Tensile Failure Tensile failure occurs when the stress imposed by drilling mud exceeds the tensile strength of formations (To). The extremely excessive weight of drilling mud creates hydraulic fracture, which triggers massive circulation loss and matrix deformation. Hence, this failure becomes the upper limit of the mud density window in safe drilling practice. Tensile failure usually occurs when the least effective principal stress surpasses the formation rock tensile
strength. Mathematically this criterion can be expressed as follows (Simangunsong et al., 2006; Zhang et al, 2006) : 3 Pp To (Eq. 5) The tensile strength of the rock can be assumed to be equal to zero because, theoretically, a fracture initiates in a flaw, a joint, or an existing fracture. To apply the criteria in Eq. 5 all principal stresses are subject to tensor transformations (Simangunsong at al., 2006). Tensile stress magnitudes can be ordered in 3 different ways, as shown in Table 4 (Bowes and Procter, 1997).
Rud.-geol.-naft. zb., Vol. 19, 2007. B. Pai, N. Gaurina-Meimurec, D. Matanovi: Wellbore instability: Causes and... Table 4 Tensile failure types Tablica 4. Tipovi vlanog loma
97
Failure type
Figure
This failure is concentric with the borehole. A low mud weight would favor the failure due to the magnitude of r being lower.
This failure creates a vertical fracture parallel with the maximum horizontal stress direction. This is because, this orientation is the tangential stress has to overcome the smallest formation tensile strength.
Conclusion The application of relatively new technologies (underbalanced drilling, slimhole completions, re-entry wells with open hole buildup sections, and multilateral wells) have to take into consideration, during the well planning stage, the risk of wellbore instability. The objective of a wellbore stability assessment is to quantify the influence of those parameters that affect the integrity of a given well such as lack of sufficient wellbore pressure, pore pressure transmission, hole inclination and others. The results of the wellbore stability assessment have to be used to mitigate the consequences of the instability. A wide variety of analytical and numerical models exist for prediction wellbore stresses and modes of instability for nearly all possible loading conditions, well geometries, rock properties and wellbore fluids. Dedicated laboratory tests and in-situ stress measurements are desirable to have more confidence in predictions achieved with analytical or numerical modeling tools. Every well should be evaluated
individually based on next criteria: the type of anticipated problems, their potential severity, the quantity and quality of data needed for a proper analysis, time and budget, and the success of previous analyses of particular type.
Accepted:03.08.2007. Received:05.09.2007. Nomenclature: az = Well azimuth, degree Co = Cohesive strength, Pa E = Youngs modulus, Pa iw = Well Inclination, degrees Pp = Pore pressure, Pa Pi = Initial pore pressure, Pa pw = Wellbore pressure, Pa r = Near wellbore position, m rw = Wellbore radius, m Ti = Initial formation temperature, degrees Tw = Wellbore wall temperature, degrees = Point location angle, degrees
98
= Internal friction angle, degrees 1 = Maximum principle stress, Pa 2 = Medium principle stress, Pa 3 = Minimum principle stress, Pa h = Minimum in-situ horizontal stress, Pa H = Maximum in-situ horizontal stress, Pa To = The tensile strength of formation rock, Pa r = Radial normal stress at wellbore, Pa t = Hoop stress at wellbore, Pa a = Axial stress at wellbore, Pa x = Normal stress in x-direction, Pa y = Normal stress in y-direction, Pa
Rud.-geol.-naft. zb., Vol. 19, 2007. B. Pai, N. Gaurina-Meimurec, D. Matanovi: Wellbore instability: Causes and... McLellan, P. (1994a): Assessing The Risk of Wellbore Instability in Horizontal and Inclined Wells, paper HWC94-14 presented at the Canadian SPE/CIM/CANMET International Conference on Recent Advances in Horizontal Well Applications, 20-23 March, Calgary, Canada. McLellan, P.J., Wang, Y., (1994b): Predicting the Effects of Pore Pressure Penetration on the Extent of Wellbore Instability: Application of a Versatile Poro-Elastoplastic Model, paper SPE/ISRM 28053 prepared for presentation at the 1994 Eurock SPE/ISRM Rock Mechanics in Petroleum Engineering, Delft, The Netherlands, 2931 August 1994. McLean, M.R. Addis, M.A. (1990): Wellbore Stability Analysis: A Review of Current Methods of Analysis and Their Field Application, paper IADC/SPE 19941 presented at the 1990 IADC/SPE Drilling Conference, 27 February - 2 March, Houston, Texas. Morita, N., Ross, C.K. (1993): Core-Based HorisontalHorizontal or Highly Inclined Well Stability Analysis for Unconsolidated Formations, paper SPE 26332 presented at the 68th Annual Technical Conference and Exhibition of the Society of Petroleum Engineers, 3-6 October, Houston, Texas. Mohiuddin, M.A., Awal, M.R., Abdulraheem, A., Khan, K. (2001): A New Diagnostic Approach to Identify the Causes of Borehole Instability Problems in an Offshore Arabian Field, paper SPE 68095 presented at the 2001 SPE Middle East Oil Show, 17-20 March, Bahrain. Nguyen, V., Abousleiman, Y., Hoang, S. (2007): Analyses of Wellbore Instability in Drilling Through Chemically Active Fractured Rock Formations: Nahr Umr Shale, paper SPE 105383 presented at the 15th SPE Middle East Oil & Gas Show and Conference, 11-14 March, Bahrain International Exhibition Centre, Kingdom of Bahrein. Ottesen, S., Kwakwa, K.A. (1991): A Multidisciplinary Approach to InSitu Stress Determination and Its Application to Wellbore Stability Analysis, paper SPE/IADC 21915 presented at the 1991 SPE/IADC Drilling Conference, 11-14 March, Amsterdam. Simangunsong, R.A., Villatoro, J.J., Davis, A.K. (2006): Wellbore Stability Assessment for Highly Inclined Wells Using Limited Rock-Mechanics Data, paper SPE 99644 presented at the 2006 SPE Annual Technical Conference and Exhibition, 24-27 September, San Antonio, Texas, U.S.A. Tan, C.P., Chen, X., Willoughby, D.R., Choi, S.K., Wu, B., Rahman, S.S., Mody, F.K. (1999): A Keep It Simple: Simple Approach for Managing Shale Instability, paper SPE/IADC 52866 presented at the 1999 SPE/IADC Drilling Conference, 9-11 March, Amsterdam, Holland. Tan, C.P., Willoughby, D.R. (1993): Critical Mud Weight and Risk Countour Plots for Designing Inclined Wells, paper SPE 26325 presented at the 68th Annual Technical Conference and Exhibition of the Society of Petroleum Engineers, 3-6 October, Houston, Texas. Tan, C.P., Yaakub, M.A., Chen, X., Willoughby, D.R., Choi, S.K., Wu, B. (2004): Wellbore Sability of Extended Reach Wells in an Oil Field in Sarawak Basin, South China Sea, paper SPE 88609 presented at the SPE Asia Pacific Oil and Gas Conference and Exhibition, 18-20 October, Perth, Australia. Zhang, J., Yu, M., Al-Bazali, T.M., Ong, S., Chenevert, M.E., Sharma, M.M., Clarc, D.E. (2006): Maintaining the Stability of Deviated and Horizontal Wells: Effects of Mechanical, Chemical, and Thermal Phenomena on Well Designs, paper SPE 100202, presented at the 2006 SPE International Oil & Gas Conference and Ehibition in China in Beijing, China, 5-7 December. This paper is based on results of research on the project 195-19513901394 Rocks/drilling Fluids Interaction Studies financed by Ministry of Science, Education and Sports.
r = Shear stress at wellbore, Pa xy = In-situ shear stress in (x,y,z) coordintaed system, Pa yz = In-situ shear stress in (x,y,z) coordintaed system, Pa zz = In-situ shear stress in (x,y,z) coordintaed system, Pa = Poisson ration, dimensionless p = Biots constant, dimensionless t = Volumetric-thermal-expansion-constant, degrees-1
References
Awal, M.R., Khan, M.S., Mohiuddin, M.A., Abdulraheem, A., Azeemuddin, M. (2001): A New Approach to Borehole Trajectory Optimization for Increased Hole Stability, paper SPE 68092 presented at the 2001 SPE Middle East Oil Show, 17-20 March, Bahrain. Bowes, C., Procter, R. (1997): Drillers Stuck Pipe Handbook, 1997 Guidelines & Drillers Handbook Credits, Schlumberger, Ballater, Scotland. Bradley, W. (1978): Bore Hole Failure Near Salt Domes, paper SPE 7503 presented at the 53th Annual Fall Technical conference and Exibition of the SPE of AIME, 1-3 October, Houston, Texas. Chen, X., Tan, C.P., Haberfield, C.M. (1998): A Comprehensive Practical Approach for Wellbore Instability Management, paper SPE 48898 presented at the 1998 SPE International Conference and Exhibition in China, 2-6 November, Bejing. Gaurina-Meimurec, N. (1994): Mechanical Factors of Wellbore Instability, Nafta 45 (3), Zagreb. Gaurina-Meimurec, N. (1998): Horizontal Well Drill-In Fluids, Rudarsko-geoloko-naftni zbornik, Vol. 10, Zagreb. Hawkes, C.D., McLellan, P.J. (1997): A New Model for Predicting TimeDependent Failure of Shales: Theory and Application, paper 97-131 presented at the 48th Annual Technical Meeting of The Petroleum Society, 8-11 June, Calgary, Canada. Kristiansen, T.G. (2004): Drilling Wellbore Stability in the Compacting and Subsiding Valhall Field, paper IADC/SPE 87221 presented at the IADC/SPE Drilling Conference, 2-4 March, Dallas, Texas, U.S.A. Lomba, R.F.T., Chenevert, M.E., Sharma, M.M. (2000): The Role of Osmotic Effects in Fluid Flow Through Shales, Journal of Petroleum Science and Engineering 25, 23-25. Maury, V.M., Sauzay, J-M. (1987): Borehole Instability: Case Histories, Rock Mechanics Approach, and Results, paper SPE/IADC 16051, presented at the 1987 SPE/IADC Drilling Conference held in New Orleans, LA, March 15-18. Martins, A.L., Santana, M.L., Goncalves, C.J.C., Gaspari, E., Campos, W., Perez, J.C.L.V. (1999): Evaluating the Transport of Solids Generated by Shale Instabilities in ERW Drilling Part II: Case Studies, paper SPE 56560 presented at the 1999 SPE annual Technical Conference and Exhibition, 3-6 October, Houston, Texas.