SKF Maintenance and Lubrication Products July 2017
SKF Maintenance and Lubrication Products July 2017
SKF Maintenance and Lubrication Products July 2017
Lubrication Products
Extending the Bearing Life Cycle
Basic
condition Mounting
monitoring
Alignment Lubrication
Mounting and dismounting
Mechanical tools 10
Heating tools 40
Hydraulic tools 52
Instruments
Alignment 78
Basic condition monitoring 98
Lubrication
Lubricants 132
Automatic grease dispensing tools 158
Manual grease dispensing tools 172
Transfer tools 179
SKF Maintenance and Lubrication Products Accessories 180
Our mission is to maximize our customer bearing Storage tools 182
performance through effective lubrication and Oil inspection and dispensing 183
maintenance solutions. Lubrication analysis tools 186
Lubrication software 188
1
The SKF Bearing Life Cycle
Help your bearing achieve its maximum service life
Every bearing has a certain service life potential. However, research has shown that, for
various reasons, not every bearing achieves it. Important stages which have a major impact
on a bearing service life can be recognised during the bearings lifecycle. These stages are
mounting, lubrication, alignment, basic condition monitoring and dismounting.
The stages in a bearing life cycle are extremely important for achieving the maximum service
life of the bearing. By applying the right maintenance practices and using the correct tools,
you can considerably extend your bearings service life and increase plant productivity and
efficiency.
Mounting Lubrication
Includes mechanical fitting tools, Includes bearing greases, manual and
induction heaters and hydraulic automatic lubricators and lubrication
equipment accessories
Mounting is one of the critical stages of the bearings lifecycle. If the Correct bearing lubrication is an essential step in reaching the bearings
bearing is not mounted properly using the correct method and tools, the service lifetime. It is important to select grease suitable for the bearings
bearings service lifetime will be reduced. Individual applications may application, and to apply the correct quantity before commissioning the
require mechanical, heat or hydraulic mounting methods for correct bearing. During operation, the bearing will require periodic relubrication.
and efficient bearing mounting. Selecting the correct mounting The right quantity of the right grease applied at the right intervals is
technique for your application will help you extend your bearings essential to achieving optimum bearing performance and maximum
service life and reduce costs resulting from premature bearing failure, service life. Using manual relubrication methods is common practice;
as well as potential damage to the application. however, continuous relubrication offers many advantages. Continuous
relubrication can be performed by using automatic lubricators, which
provide a more consistent, correct and contamination-free grease supply.
After the bearing has been mounted in an application such as a motor During operation, it is important to regularly inspect the condition of
connected to a pump, the application should be aligned. If the application the bearing by performing basic condition monitoring measurements.
is not properly aligned, the misalignment can cause the bearing to suffer These regular inspections will allow the detection of potential problems
additional load, friction and vibration. These can accelerate fatigue and and help to prevent unexpected machine stops. Consequently, the
reduce the bearings, as well as other machine components, service life. machine maintenance can be planned to suit the production schedule,
Furthermore, increased vibration and friction can significantly increase increasing the plants productivity and efficiency.
energy consumption and the risk of premature failures.
2
Dismounting Buy a bearing
Basic
condition Mounting
monitoring
Alignment Lubrication
Dismounting
Includes pullers, both mechanical and
hydraulic, induction heaters and
hydraulic equipment
At some point, the bearing will reach the end of its service life and will
have to be replaced. Although the bearing may not be used again, it is Inside this catalogue, you will find SKFs complete range of
extremely important to dismount it correctly so that the service life of the maintenance products which can help you get the maximum
replacement bearing is not compromised. Firstly, the use of proper service life from your bearings. For more information about
dismounting methods tools will help prevent damage to other machine SKF maintenance products or to order any of these products,
components, such as the shaft and housing, which are often re-used. please contact your local SKF authorised distributor or SKF sales
Secondly, incorrect dismounting techniques can be hazardous to company. On the Internet, SKF can be found at www.skf.com.
maintenance personnel. SKF Maintenance Products can be found at www.mapro.skf.com.
3
The importance of maintenance and lubrication
The importance of maintenance and lubrication on the total cost of ownership is often underestimated
Energy consumption
Machine Machine downtime
Product spoilage
Premature wear
Bearing / component Spare and repair cost
Hand labour
Impact
Focusing on the right maintenance and lubrication practices,
with proper equipment and training, helps increase reliability,
reduce operating costs and improve worker safety
Thanks to SKFs unique knowledge of machinery operation and Continuous development and improvement of our products is made in
maintenance, we understand the issues that operators and cooperation with users and naturally we take account of regulatory
maintenance personnel have to deal with every day. bodies and applicable international standards to improve reliable
rotating equipment performance and safety.
With a focus on the bearing life cycle and machine operations, we
develop and maintain a comprehensive product range to support you.
Safety, ease of use, affordability and effectiveness are key product
characteristics and drivers of our daily activities.
4
Main causes of premature bearing failures
Poor fitting
16%
Around 16% of all premature bearing failures are caused by poor fitting
(usually brute force...) and maintenance personnel being unaware of the
availability of the correct fitting tools. Individual installations may require
mechanical, hydraulic or heat application methods for correct and efficient mounting or
dismounting. SKF offers a complete range of tools and equipment to make these tasks easier,
quicker and more cost effective, backed up by a wealth of service engineering know-how.
Professional fitting, using specialised tools and techniques, is another positive step towards
achieving maximum machine uptime.
Poor lubrication
36%
Although sealed-for-life bearings can be fitted and forgotten, some 36%
of premature bearing failures are caused by incorrect specification and
inadequate application of the lubricant. Inevitably, any bearing deprived
of proper lubrication will fail long before its normal service life. Because bearings are usually
the least accessible components of machinery, neglected lubrication frequently compounds the
problem. Wherever manual maintenance is not feasible, fully automatic lubrication systems can
be specified by SKF for optimum lubrication. Effective lubrication and using only recommended
SKF greases, tools and techniques helps to significantly reduce downtime.
Contamination
14%
A bearing is a precision component that will not operate efficiently unless
both the bearing and its lubricants are isolated from contamination. And,
since sealed-for-life bearings in ready-greased variants account for only a small
proportion of all bearings in use, at least 14% of all premature bearing failures are attributed to
contamination problems. SKF has an unrivalled bearing manufacturing and design capability and
can tailor sealing solutions for the most arduous operating environments.
Fatigue
34%
Whenever machines are overloaded, incorrectly serviced or neglected,
bearings suffer from the consequences, resulting in 34% of all premature
bearing failures. Sudden or unexpected failure can be avoided, since neglected
or overstressed bearings emit early warning signals which can be detected and interpreted using
SKF condition monitoring equipment. The SKF range includes hand-held instruments, hard-wired
systems and data management software for periodic or continuous monitoring of key operating
parameters.
5
Poor bearing mounting
techniques can
significantly reduce the
bearing service life.
Mark Ely,
Product Manager
6
Mounting and dismounting
Mechanical tools 10
Heating tools 40 Dismounting Buy a bearing
Hydraulic tools 52
Basic
condition Mounting
monitoring
Alignment Lubrication
7
SKF methods and tools
Mounting Dismounting
Around 16% of all premature bearing failures are a result When dismounting bearings, care must be taken not to
of poor fitting or using incorrect mounting techniques. damage other machine components, such as the shaft or
Selecting the correct mounting technique for your housing, as damage can compromise the machines
application will help you extend your bearings service life efficiency and lifetime. Individual applications may require
and reduce costs resulting from premature bearing mechanical, heat or hydraulic dismounting methods and
failure, as well as potential damage to the application. tools to allow safe, correct and efficient bearing
dismounting.
8
Shaft seatings Mounting tools Dismounting tools
Mechanical Hydraulic Oil injection Heaters Mechanical Hydraulic Oil injection Heaters
Small
Cylindrical seating bearings
Medium
bearings
Large
bearings
Cylindrical roller
bearing types NU,
NJ, NUP, all sizes
Small
Tapered seating bearings
Medium
bearings
Large
bearings
Small
Adapter sleeve bearings
1)
Medium
bearings
Large
bearings
Small
Withdrawal sleeve bearings
Medium
bearings
Large
bearings
Small bearings: bore diameter <80 mm / Medium bearings: bore diameter 80200 mm / Large bearings: bore diameter >200 mm / 1) Only for self-aligning ball bearings.
Jaw Strong back Hydraulic Fitting Hook Impact Hydraulic nut Drive-up Oil Injection Hot plate Aluminium
puller puller puller tool spanner spanner and pump Method Method Induction ring, EAZ
page 22 page 28 page 25 page 10 page 12 page 16 page 56 page 54 page 52 heater heater
page 40 page 48
9
Mechanical mounting
Helps prevent premature bearing failures
SKF Bearing Fitting Tool Kit TMFT series
Poor fitting, usually using brute force, accounts for 16% of premature bearing
failures. SKF Bearing Fitting Tool Kits are designed for quick and precise
mounting of bearings, while minimising the risk of bearing damage.
The right combination of impact ring and sleeve allows effective transmission of mounting force to
the bearing ring with the interference fit, minimising the risk of damaging the bearings raceways
or rolling elements. In addition to mounting bearings, the TMFT series are also suitable for
mounting other components such as bushings, seals and pulleys. The TMFT 36 kit contains
36 impact rings and the TMFT 24 contains 24 rings. Both kits have 3 impact sleeves and a
dead-blow hammer packed in a lightweight carrying case.
The TMFT 36 facilitates the mounting of Click connection between impact ring and
different bearings with bore diameters sleeve provides stability and durability
from 1055 mm The impact rings are suitable for use under
The TMFT 24 facilitates the mounting of a press
different bearings with bore diameters Impact rings are marked for clear visual
from 1545 mm identification of the rings size and easy
Facilitates correct mounting on shaft, selection
housing and blind applications Even surface of the impact sleeves body
The diameter of the impact ring precisely fits provides excellent grip
the inner and outer diameter of the bearing The nylon double-side head of the dead-
Small diameter of the impact area on top of blow hammer helps to prevent damaging
the sleeve allows effective transmission and the components
distribution of mounting force The rubber handgrip of the dead-blow
Impact rings and sleeves are made of high hammer provides excellent grip
impact resistant material for longevity
NEW
Technical data
Designation TMFT 24 TMFT 36
Impact rings
Bore diameter 1545 mm (0.591.77 in.) 1055 mm (0.392.17 in.)
Outer diameter 32100 mm (1.263.94 in.) 26120 mm (1.024.72 in.)
Sleeves
Maximum shaft length Sleeve A: 220 mm (8.7 in.) Sleeve A: 220 mm (8.7 in.)
Sleeve B: 220 mm (8.7 in.) Sleeve B: 220 mm (8.7 in.)
Sleeve C: 225 mm (8.9 in.) Sleeve C: 225 mm (8.9 in.)
Hammer TMFT 36-H, weight 0,9 kg (2.0 lb) TMFT 36-H, weight 0,9 kg (2.0 lb)
Carrying case dimensions 530 110 360 mm (20.9 4.3 14.2 in.) 530 110 360 mm (20.9 4.3 14.2 in.)
Number of rings 24 36
Number of sleeves 3 3
Weight
(including carrying case) 4,0 kg (8.9 lb) 4,4 kg (9.7 lb)
10
TMFT 24 is suitable for SKF bearing series
DGBB DGBB (sealed) SABB SRACBB DRACBB SRB CRB TRB CARB
6002 6009 62202 62209 1202 1209 7002 7009 3202 3209 21305 21309 N 1005 N 1009 30203 30209 C 2205 C 2209
6202 6209 62302 62309 1302 1309 7202 7209 3302 3309 22205/20 N 202 N 209 30302 30309 C 6006
6302 6309 63002 63009 2202 2209 7302 7309 22205 22209 N 2203 N 2209 31305 31309
6403 6407 2302 2309 22308 22309 N 2304 N 2309 32004 32009
62/22 11207 11209 N 3004 N 3009 32205 32209
62/28 N 303 N 309 32303 32309
63/22 33205 33209
63/28
16002 16009
98203 98206
Incorrect mounting
When bearings are mounted cold, care must be taken to ensure
the drive-up forces are applied to the ring with the interference fit.
Damage to the bearing resulting in a failure can occur if the mounting
force is transmitted through the rolling elements causing damage
to the raceways. Uneven distribution of forces can result in raceway damage
Correct mounting
The correct way to minimise raceway damage is to use specifically
designed tools from SKF, such as the Bearing fitting tool kits and
Combi kits. These tools allow drive-up forces to be applied effectively
and evenly to the component with the interference fit, avoiding
raceway damage. With the correct tools, raceway damage is avoided
11
Spanners and sockets
Incorrect mounting
Bearing driven up too far and all clearance removed;
damage possible.
Correct mounting
Bearing driven up the correct distance and the right
clearance is achieved.
The comprehensive range of SKF spanner and sockets are used to tighten and loosen
many types and sizes of bearing lock nuts, for bearings mounted directly on a shaft or
on sleeves.
12
Selection chart HN series
Designation Suitable for the following series of SKF lock nuts
KM N AN KMK KMFE KMT DIN 1804 (M)
HN 0 0 0 0 M60,75, M81
HN 1 1 1 1
HN 2-3 2, 3 2, 3 2, 3 0 M101, M121,5
HN 4 4 4 4 4 1, 2 M141,5, M161,5
HN 5-6 5, 6 5, 6 5, 6 5, 6 3, 4, 5 M221,5, M241,5, M261,5
HN 7 7 7 7 7 6, 7 M281,5, M301,5, M321,5, M351,5
HN 8-9 8, 9 8, 9 8, 9 8, 9 8 M381,5, M401,5, M421,5
HN 10-11 10, 11 10, 11 10, 11 10, 11 9, 10 M451,5, M481,5, M501,5
HN 12-13 12, 13 12, 13 12, 13 12, 13 11, 12 M521,5, M551,5, M581,5, M601,5
HN 14 14 14 14 14
HN 15 15 15 15 15 13, 14 M621,5, M651,5, M681,5, M701,5
HN 16 16 16 16 16 15
HN 17 17 17 17 17 16 M721,5, M751,5, M802
HN 18-20 18, 19, 20 18, 19, 20 18, 19, 20 18, 19, 20 17, 18, 19 M852, M902
HN 21-22 21, 22 22 21, 22 21, 22 20, 22 M952, M1002
13
Easy and quick bearing mounting and dismounting in SNL housings
SKF Hook Spanners HN ../SNL series
Unique design allows the SKF HN ../SNL series to be used inside
SKF SNL, FSNL, SNH and SE bearing housings
Suitable for tightening and loosening a wide selection of lock nuts,
facilitating their use in a wide range of housing and shaft applications
The large contact area of the spanner around the nut provides
excellent grip and force transmission
Exact fit reduces the risk of shaft, nut and housing damage
14
Easy mounting and dismounting without nut damage
SKF Axial Lock Nut Sockets TMFS series
Requires less space around the bearing arrangement
than hook spanners
Inch connections for power tools or torque wrenches
SKF TMFS fits nuts of series KM, KMK (metric) and KMF
Special versions are available on request
1) KM 0 only
15
High impact forces without nut damage
SKF Impact Spanners TMFN series
Designed for safely tightening and loosening a wide selection of larger lock nuts
Not intended to be used to drive bearings up a tapered seating
Helps avoid shaft and nut damage
Safe and user friendly
Impact applied effectively to the nut
Special wide impact face
To be used in combination with a hammer
Technical data
Designation d f h
mm in. mm in. mm in.
TMFN 23-30 148 5.83 11,5 0.45 4,4 0.17
TMFN 30-40 193 7.60 13,5 0.53 5,3 0.21
TMFN 40-52 248 9.76 16 0.63 6,5 0.26
TMFN 52-64 316 12.44 19 0.75 8,5 0.33
TMFN 64-80 396 15.59 23 0.91 11 0.43
TMFN 80-500 516 20.31 28 1.10 13 0.51 h
TMFN 500-600 626 24.65 36 1.42 16 0.63 f
TMFN 600-750 746 29.37 40 1.57 19 0.75 d
16
For achieving the correct radial clearance
SKF Bearing Lock Nut Spanner TMHN 7 series
The SKF TMHN 7 set of lock nut spanners is especially designed for mounting
self-aligning ball bearings as well as small spherical roller and CARB toroidal
roller bearings on tapered seatings. Using the SKF TMHN 7, minimises the
risk of over-tightening of the lock nut, which can remove the bearings radial
clearance resulting in bearing damage.
STOP
17
Mounting and dismounting
Multi-purpose kits for quick and easy mounting and dismounting
SKF Combi Kit TMMK series
The SKF TMMK series designed for the quick and precise mounting and
dismounting of deep groove ball bearings from shafts, housings and blind
housings. The TMMK 10-35 suits bearings with bore diameters from
10 to 35 mm, whereas the TMMK 20-50 suits bearings with bore diameters
TMMK 10-35 from 20 to 50 mm.
For mounting, a multi-purpose fitting tool is included which is suitable for mounting bearings as
well as bushings, seal rings, belt pulleys and other similar products. For dismounting of deep
groove ball bearings from blind housings and shafts, the SKF TMMK series contains a unique
three-armed puller. When dismounting deep groove ball bearings from housings, a combination
NEW of this puller, sliding hammer and support rings enables easy removal of the bearings.
The correct combination of impact ring and The claws are especially designed to facilitate
sleeve helps ensure that mounting forces are a precise fit in the bearings raceways,
not transmitted via the rolling elements of providing good grip and allowing the
the bearing, minimizing damage to bearing application of higher dismounting forces
TMMK 20-50 due to incorrect mounting The designation is laser-engraved on the
The impact rings are made of high-impact arms allowing easy identification and
modified polyamide. The impact sleeves are selection
made of glass fibre-reinforced, high-impact The springs are colour-coded allowing easy
modified polyamide, which is super-tough, selection and matching
Mounting strong and lightweight Elastic locking ring results in easy connection
The dead-blow hammer has nylon faces and of puller arms to spindle
is steel-shot loaded for maximum impact. Heavy sliding weight of the sliding hammer
The handle, with comfortable rubber-grip generates a high dismounting force
for good handling, absorbs shock and Heavy sliding weight of the sliding hammer
vibration generates a high dismounting force
Technical data
Dismounting
Designation TMMK 10-35 TMMK 20-50
Number of impact rings 24 21
Number of sleeves 2 2
Impact rings bore diameter 1035 mm 2050 mm
(0.391.38 in.) (0.791.97 in.)
Impact rings outer diameter 2680 mm 42110 mm
(1.023.15 in.) (1.654.33 in.)
Dead-blow hammer TMFT 36-H TMFT 36-H
Dimensions of case 530 110 360 mm 530 110 360 mm
(20.9 4.3 14.2 in.) (20.9 4.3 14.2 in.)
Dismounting Weight 7,6 kg (16.8 lb) 8,5 kg (18.6 lb)
18
Mounting
TMMK 10-35 is suitable for SKF bearing series
DGBB DGBB (sealed) SABB SRACBB DRACBB SRB CRB TRB CARB
6000 6007 62200 62207 1200 1207 7000 7007 3200 3207 21305 21307 N 1005 N 1007 30203 30207 C 2205 C 2207
6200 6207 62300 62307 129 7200 7207 3302 3307 22205/20 N 202 N 207 30302 30307 C 6006
6300 6307 63000 63007 1301 1307 7301 7307 22205 22207 N 2203 N 2207 31305 31307
6403 6407 2200 2207 N 2304 N 2307 32004 32007
629 2301 2307 N 3004 N 3007 32205 32207
62/22 11207 N 303 N 307 32303 32307
62/28 33205 33207
63/22
63/28
16002 16007
16100 16101
98203 98206
DGBB DGBB (sealed) SABB SRACBB DRACBB SRB CRB TRB CARB
6004 6010 62204 62210 1204 12010 7004 7010 3204 3210 21305 21310 N 1005 N 1010 30204 30210 C 2205 C 2210
6204 6210 62304 62310 1304 1310 7204 7210 3304 3210 22205/20 N 204 N 210 30304 30310 C 4010
6304 6310 63004 63010 2204 2210 7304 7310 22205 22210 N 2204 N 2210 31305 31310 C 6006
6404 6409 2304 2310 22308 22310 N 2304 N 2310 32004 32010
62/22 11207 11210 N 304 N 310 32205 32210
62/28 32304 32310
63/22 33010
63/28 33205 33210
16004 16011
98204 98206
Dismounting
TMMK 10-35 is suitable for SKF bearing series
DGBB
6000 6017 6300 6307 16002 16003
6200 6211 63/22 16011
62/22 63/28
62/28 6403
DGBB
6004 6020 6300 6313 16011 All parts are clearly arranged in the case for easy selection
6201 6218 63/22 and identification.
62/22 63/28
62/28 6403 6310
19
Dismounting
Selection chart SKF external pullers
Designation No. of arms Width of grip
mm in.
25
TMHP 50/320 3 310506 12.219.9
TMHP 50/570 3 310506 12.219.9
1) Other arm length options are available
20
Effective arm length Maximum withdrawal force
mm in. kN US ton
60 2.4 6 0.7
135 5.3 18 2.0
135 5.3 24 2.7
210 8.3 34 3.8
240 9.4 50 5.6
67 2.6 17 1.91
82 3.2 17 1.91
98 3.9 40 4.5
124 4.9 40 4.5
TMMA 75H/SET
143 5.6 50 5.6
169 6.7 50 5.6
183 7.2 60 6.7 Choosing the right puller for the job is critical. The puller type, and
238 9.4 60 6.7 its maximum withdrawal capacity are crucial for completing any
221 8.7 50 5.6 dismounting job safely and easily.
221 8.7 50 5.6
221 8.7 60 6.7
221 8.7 60 6.7
21
SKF EasyPull
Equipped with spring-operated arms and a solid design, the patented SKF EasyPull is
one of the most user-friendly and safe tools on the market. Ergonomically designed,
the spring-operated arms enable the user to position the puller behind the component
with just one movement. The SKF EasyPull is available in mechanical and hydraulically
assisted versions, as well as complete kits with a tri-section pulling plate and a puller
protection blanket.
Safe and simple bearing dismounting Quick and virtually effortless bearing dismounting
Mechanical pullers TMMA series Hydraulic pullers TMMA ..H series
Sturdy design allows dismounting of components even in the tightest Ready-to-use, integrated hydraulic cylinder, pump and puller thus
application in a safe manner it is assembly-free and it is not necessary to purchase separate parts
The unique red rings spring-operated opening mechanism allows the Safety valve prevents spindles and pullers from being overloaded if
SKF EasyPull to be placed behind the component with one movement excessive force is applied
of the hands The spring-loaded centre point on the hydraulic spindle allows easy
Self-locking arms help prevent the risk of puller slipping under load centring of the puller on the shaft without damaging the shaft
Double hexagonal heads allow easier application of withdrawal force The TMMA 100H has a maximum withdrawal force of 100 kN
Self-centring capability and nosepiece help avoid damage to shaft (11.2 US ton) and a long stroke of 80 mm (3.1 in.), which facilitates
Efficient use of time due to quick dismounting most dismounting jobs in just one operation
Available in three sizes with a withdrawal force of 60, 80 or 120 kN For dismounting jobs requiring less force, SKF offers a 75 kN
(6.7, 9.0 or 13.5 US ton), enabling easy selection (8.4 US ton) version, the hydraulic EasyPull TMMA 75H with a
TMHS series hydraulic force generators are available as an accessory maximum stroke of 75 mm (3 in.)
for the 80 and 120 kN versions Supplied with extension pieces and one nosepiece
Technical data
Designation TMMA 60 TMMA 80 TMMA 120 TMMA 75H TMMA 100H
Width of grip external, minimum 36 mm (1.4 in.) 52 mm (2.0 in.) 75 mm (3.0 in.) 52 mm (2 in.) 75 mm (3 in.)
Width of grip external, maximum 150 mm (5.9 in.) 200 mm (7.8 in.) 250 mm (9.8 in.) 200 mm (7.8 in.) 250 mm (9.8 in.)
Effective arm length 150 mm (5.9 in.) 200 mm (7.8 in.) 250 mm (9.8 in.) 200 mm (7.8 in.) 250 mm (9.8 in.)
Maximum withdrawal force 60 kN (6.7 US ton) 80 kN (9.0 US ton) 120 kN (13.5 US ton) 75 kN (8.4 US ton) 100 kN (11.2 US ton)
Claw height 7,5 mm (0.30 in.) 9,8 mm (0.39 in.) 13,8 mm (0.54 in.) 9,8 mm (0.39 in.) 13,8 mm (0.54 in.)
Hydraulic spindle TMHS 75 TMHS 100
Adapter: possible to upgrade to TMHS 75 TMHS 100
hydraulic version
Total weight 4,0 kg (8.8 lb) 5,7 kg (12.6 lb) 10,6 kg (23.4 lb) 7,0 kg (15.4 lb) 13,2 kg (29 lb)
22
A complete bearing dismounting solution
Hydraulic puller sets TMMA ..H /SET series
A set consisting of a hydraulically assisted SKF EasyPull together with
a tri-section pulling plate, TMMS series, and a puller protection
blanket facilitate an easy, safe and virtually damage-free dismounting
Especially suitable for dismounting spherical roller and CARB toroidal
roller bearings, and other components such as pulleys and flywheels
A puller protection blanket, TMMX series, made of a strong
transparent material allows the user to visually follow the
dismounting procedure. While dismounting, the blanket helps to
protect from flying fragments of bearings or other components,
thereby enhancing user safety
A sturdy custom-made storage case with room for all parts minimises
the risk of loosing or damaging the sets components
Technical data
Designation TMMA 75H/SET TMMA 100H/SET
Puller TMMA 75H TMMA 100H
Tri-section pulling plate TMMS 100 TMMS 160
Puller protection blanket TMMX 280 TMMX 350
Dimensions of case 600 235 225 mm 680 320 270 mm
(23.6 9.3 8.6 in.) (27 13 11 in.)
Total weight 15,0 kg (33.1 lb) 31,6 kg (70 lb)
23
SKF Jaw pullers
One of the most common ways to dismount small to medium size bearings
is to use a basic mechanical puller. Using an SKF puller helps to safeguard
against damage to the bearing or to the bearing seating during dismounting.
SKF Jaw pullers allow for easy and safe puller operation.
Versatile two and three arm mechanical pullers Powerful self-centring mechanical pullers
SKF Standard Jaw Pullers SKF Heavy Duty Jaw Pullers
TMMP series TMMP series
Range of five different jaw pullers with two or three arms Fast, efficient and smooth handling
Maximum nominal span from 65 to 300 mm (2.6 to 11.8 in.) Unique pantograph system gives exceptional grip and helps counteract
Cone system for automatic centring and secure positioning of arms misalignment during operation
Strong springs keep arms apart for easy operation Three arm jaw pullers with a maximum withdrawal force of 60 to
Hardened, high quality carbon steel 150 kN (6.7 to 17.0 US ton) suitable for medium to large size bearings
Blackened, high quality steel for corrosion resistance
Other arm length options are available
24
Powerful self-centring hydraulic pullers
SKF Hydraulically Assisted Heavy Duty
Jaw Pullers TMHP series
High forces can be easily applied as the puller is self-centring
The combination of a spindle and hydraulic cylinder allows the
working length to be easily adjusted
Unique pantograph system gives exceptional grip and helps
counteract misalignment during operation
Equipped with a lifting handle and eye bolt, facilitates easy handling
Maximum withdrawal force of 150, 300 or 500 kN
(17, 34 or 56 US ton)
Supplied with SKF Hydraulic Pump TMJL 100
Technical data
Designation 1) TMHP 15/260 TMHP 30/170 TMHP 30/350 TMHP 30/600 TMHP 50/140 TMHP 50/320 TMHP 50/570
Width of grip 195386 mm 290500 mm 290500 mm 290500 mm 310506 mm 310506 mm 310506 mm
(7.715.2 in.) (11.419.7 in.) (11.419.7 in.) (11.419.7 in.) (12.219.9 in.) (12.219.9 in.) (12.219.9 in.)
Effective length 264 mm 170 mm 350 mm 600 mm 140 mm 320 mm 570 mm
of arms (10.4 in.) (6.7 in.) (13.7 in.) (23.6 in.) (5.5 in.) (12.6 in.) (22.4 in.)
Claw height 30 mm (1.2 in.) 35 mm (1.4 in.) 35 mm (1.4 in.) 35 mm (1.4 in.) 40 mm (1.6 in.) 40 mm (1.6 in.) 40 mm (1.6 in.)
Stroke 100 mm (3.9 in.) 50 mm (2 in.) 50 mm (2 in.) 50 mm (2 in.) 40 mm (1.6 in.) 40 mm (1.6 in.) 40 mm (1.6 in.)
Maximum working 80 MPa 80 MPa 80 MPa 80 MPa 80 MPa 80 MPa 80 MPa
pressure hydraulic (11 600 psi) (11 600 psi) (11 600 psi) (11 600 psi) (11 600 psi) (11 600 psi) (11 600 psi)
cylinder
Maximum withdrawal 150 kN 300 kN 300 kN 300 kN 500 kN 500 kN 500 kN
force (17 US ton) (34 US ton) (34 US ton) (34 US ton) (56 US ton) (56 US ton) (56 US ton)
Weight 34 kg (75 lb) 45 kg (99 lb) 47 kg (104 lb) 56 kg (123 lb) 47 kg (104 lb) 54 kg (119 lb) 56 kg (132 lb)
Effective length optional arms
TMHP ..-1 included included 170 mm (6.7 in.) 170 mm (6.7 in.) included 140 mm (5.5 in.) 140 mm (5.5 in.)
TMHP ..-2 344 mm (14.2 in.) 350 mm (13.7 in.) included 350 mm (13.7 in.) 320 mm (12.6 in.) included 320 mm (12.6 in.)
TMHP ..-3 439 mm (17.3 in.) 600 mm (23.6 in.) 600 mm (23.6 in.) included 570 mm (22.4 in.) 570 mm (22.4 in.) included
TMHP ..-4 689 mm (27.1 in.)
1) Also available without hydraulic pump TMJL 100. Please add suffix X to designation when ordering without pump (e.g. TMHP 30/170X)
25
Versatile and robust pullers for internal and external pulling jobs
TMMR.. XL with 2 optional
extension pieces SKF Reversible Jaw Puller TMMR F series
The multi-purpose SKF Reversible Jaw Pullers are suitable for internal and
external pulling of bearings and other components, such as gears and pulleys.
The standard range of eight pullers can accommodate a wide range of bearing
and component sizes. Adding extra versatility to the TMMR..F puller programme,
the four largest sizes are also available with extra long arms as a standard option
(TMMR .XL). The extra long arms help to dismount bearings and components
placed far from the shaft end. For more versatility, the extra long arms can be
further extended by adding extension pieces.
An essential and versatile tool for every Arms and beam are zinc passivated for
workshop allows for external and internal enhanced corrosion resistance and easy
pulling applications cleaning
Self-locking arms for easy adjustment of The extra long arm extension pieces,
width of grip designed to be easy to fit and remove,
Hexagonal head on beam enables rotation of can be used to further increase the effective
puller and bearing during dismounting, arm length. Using extension pieces does
improving ease of use not compromise the overall puller strength
Wide gripping range from 23 mm (0.9 in.) The SKF Reversible Jaw Pullers can also be
internal to 350 mm (13.8 in.) external, supplied as three different sets, complete
enables many bearings and components to with a workshop stand
be dismounted
Unlike many similar pullers, the pullers can be
used up to their full rated load capacity without
permanently deforming the puller arms
Technical data
Designation Maximum Width of Width of Effective
withdrawal grip external grip internal arm length
force pull (D) pull (d) (L)
kN US ton mm in. mm in. mm in.
External pull Internal pull TMMR 40F 17 1.9 2348 0.91.9 5967 2.32.6 67 2.6
TMMR 60F 17 1.9 2368 0.92.7 6287 2.43.4 82 3.2
TMMR 80F 40 4.5 4183 1.63.3 9597 3.73.8 98 3.9
TMMR 120F 40 4.5 41124 1.64.9 95139 3.75.5 124 4.9
L L
TMMR 160F 50 5.6 68164 2.76.5 114163 4.56.4 143 5.6
TMMR 200F 50 5.6 65204 2.68.0 114204 4.58.0 169 6.7
D d
TMMR 250F 60 6.7 74254 2.910.0 132254 5.29.9 183 7.2
TMMR 350F 60 6.7 74354 2.913.9 135354 5.313.8 238 9.4
26
Technical data
TMMR.. F
TMMR 40F
TMMR 60F
TMMR 80F
TMMR 120F
TMMR 160F
TMMR 200F
TMMR 250F
TMMR 350F
TMMR 16/20XL-1
TMMR 16/20XL-1 TMMR 25/35XL-1
TMMR 16/35XL-5 TMMR 25/35XL-1
TMMR 16/35XL-5
Accessories
TMMR 16/20XL-1 Extra long arm set to convert TMMR 160F and TMMR 200F to XL version
TMMR 25/35XL-1 Extra long arm set to convert TMMR 250F and TMMR 350F to XL version
TMMR 16/35XL-4 Extension arms set for the TMMR.. XL
TMMR 16/35XL-4
TMMR 16/35XL-5 Spring-loaded nose piece
Technical data
Designation TMHP 10E
Contents 1 armassembly stand Maximum stroke 80 mm (3.1 in.)
3 arms, 115 mm (4.5 in.) Threading hydraulic cylinder 1 1/2"-16 UN
3 arms, 160 mm (6.3 in.)
3 arms, 200 mm (7.9 in.) Nominal working force 100 kN (11.2 US ton)
1 hydraulic spindle TMHS 100 Carrying case dimensions 578 410 70 mm (23 16 2.8 in.)
3 extension pieces for hydraulic spindle;
50, 100, 150 mm (2, 4, 6 in.) Weight 14,5 kg (32 lb)
1 nosepiece with centre point
for hydraulic spindle
27
SKF Strong Back Pullers
Easy bearing dismounting even in the tightest spaces
SKF Strong Back Pullers TMBS E series
The SKF TMBS E strong back pullers facilitate dismounting of bearings in
applications where the use of traditional jaw pullers is restricted due to lack
of space or where the application demands a long reach.
Special separator design allows the puller to SKF TMBS 50E is equipped with a
be easily inserted between the bearing and mechanical spindle for force generation
the shoulder on the shaft SKF TMBS 100E and the SKF TMBS 150E
The spring-loaded centre point of the are equipped with a hydraulic spindle, which
hydraulic spindle allows easy puller centring allows for easy application of force up to
The firm grip behind the bearings inner ring 100kN (11.2 US ton)
reduces the force required to dismount the Supplied with hydraulic spindle extension
bearing pieces to allow quick adaptation to pulling
The hydraulic spindle is equipped with a length
safety valve, which minimises the risk of SKF TMBS 100E and SKF TMBS 150E are
puller overload supplied with extension rods to allow quick
A hydraulic spindle stroke of 80 mm (3.1 in.) adaptation to pulling lengths upto 816 mm
helps facilitate dismounting in one operation (32.1 in.)
Selection chart
Designation Shaft diameter Maximum bearing outer Maximum reach
diameter
mm in. mm in. mm in.
TMBS 50E 750 0.31.9 85 3.3 110 4.3
TMBS 100E 20100 0.83.9 160 6.3 120816 4.732.1
TMBS 150E 35150 1.45.9 215 8.5 120816 4.732.1
TMHC 110E 20100 0.83.9 160 6.3 120245 4.79.6
28
Technical data TMBS E series
29
SKF Blind housing pullers
Selection chart SKF Blind pullers
The SKF Deep Groove Ball Bearing Puller Kit TMMD 100 allows quick and
Designation Bearing bore Effective arm easy dismounting of SKF Deep Groove Ball Bearings with an interference fit
diameter (d) length
on both rings.
TMMD 100 10100 mm 135170 mm
(0.43.9 in.) (5.36.7 in.) The SKF Blind Housing Puller Kit TMBP 20E is an adapter type puller for
TMBP 20E 30160 mm 547 mm
(1.26.3 in.) (21.5 in.)
dismounting deep groove ball bearings in blind housings with shaft dimensions
between 30 mm and 160 mm (1.186.3 in.). The use of extension rods allows a
long reach of up to 547 mm (21.5 in.).
Suitability chart
SKF TMBP 20E is suitable for dismounting the following deep groove ball bearings
90 90
Remove seal and open selected section of Insert appropriate bearing adapter and rotate Insert the second adapter into prepared area
ball cage. Clean the swarf out. it 90 ensuring positive grip within the bearing diametrically opposed.
race.
30
Easy dismounting of bearings in blind housings
32
Suitability chart
The SKF TMMD 100 suits the following bearing series and sizes:
Bearing selection chart included The rubber cap allows easy and quick Optimised puller claw design firmly grips the
attachment of the arms to the spindle. It also outer raceway of SKF bearings, without the
prevents the puller arms from detaching from need of removing the bearing cage.
the spindle during operation
31
Technical data SKF Blind Housing Puller Kit
Designation TMBP 20E
Kit contents 6 adapters sizes (2 pcs each), 2 main rods (with nut support rings and nuts)
4 extension rods, Spindle, Spindle nose piece, Beam
Effective arm length 147547 mm (5.821.5 in.)
Maximum pulling force 55 kN (6.2 US ton)
Carrying case dimensions 530 85 180 mm (20.9 3.4 7.0 in.)
Weight 6,5 kg (14.3 lb)
The above tables only show a selection of popular bearings that can be dismounted using SKF Internal Pullers.
There may be other bearings that can also be removed using the SKF TMIP or TMIC pullers.
32
Internal pullers
Fast and easy bearing dismounting from housings
SKF Internal Bearing Puller Kits
TMIP and TMIC series
The SKF Internal Bearing Puller Kits are designed for dismounting bearings
TMIP TMIC from housings, where the fit is on the outer ring. The pullers are constructed
series series
for optimum strength and durability and suit a wide range of bearing bore
diameters. A sliding hammer allows high impact forces to be applied and is
ergonomically designed to enhance user safety.
NEW
Technical data
Designation TMIC 728 TMIP 728 TMIP 3060
Bearing bore diameter 728 mm (0.281.1 in.) 728 mm (0.281.1 in.) 3060 mm (1.22.4 in.)
Total sliding hammer length 417 mm (16.4 in.) 417 mm (16.4 in.) 557 mm (21.9 in.)
Carrying case dimensions 530 85 180 mm 530 85 180 mm 530 85 180 mm
(20.9 3.4 7.0 in.) (20.9 3.4 7.0 in.) (20.9 3.4 7.0 in.)
Weight 3,0 kg (6.6 lb) 3,1 kg (6.8 lb) 5,4 kg (11.9 lb)
33
Puller accessory selection guide
A range of accessories has been developed to further facilitate
the ease of use of the SKF puller range.
Puller series
TMMP series
Standard Heavy duty Standard jaw pullers
jaw pullers jaw pullers
TMMP series
24 Heavy duty jaw pullers
TMMR F series
Reversible jaw pullers
26
TMMA series
SKF EasyPull
22
TMHC 110E
Hydraulic Puller kit
TMHP 10E
Hydraulic Puller kit
TMBS E series
27, 28 Strong back pullers
TMHP series
Hydraulically - assisted
heavy duty jaw pullers
25
34
38 36 37
TMMP 2x65
TMMP 2x170 TMMX 280
TMMP 3x185 TMMX 210 1) TMMS 50 1) TMMS 100
TMMP 3x230 TMMX 210 TMMX 280 1) TMMS 50 1) TMMS 100
TMMP 3x300 TMMX 280 TMMX 350 1) TMMS 50 TMMS 100 1) TMMS 160
TMMR 40F
TMMR 60F
TMMR 80F
TMMR 120F TMMX 210
TMMR 160F (XL) TMMX 210 TMMX 280
TMMR 200F (XL) TMMX 280 1)
TMMR 250F (XL) TMMX 350 1)
TMMR 350F (XL)
TMHC 110E TMMX 210 TMMX 280 1) TMMX 350 TMHS 100 2)
TMHP 10E TMMX 210 TMMX 280 1) TMMX 350 TMHS 100 2) TMMS 50 1) TMMS 100 1) TMMS 160
35
Effortless withdrawal force generation
Advanced Hydraulic Spindles TMHS 75 and TMHS 100
The SKF TMHS 75 and TMHS 100 generate a high pulling force with very little
effort compared to the standard mechanical spindles. They significantly reduce
the time needed to dismount a bearing or other component.
TMHS 75
TMHS 75:
Maximum withdrawal force of 75 kN (8.4 US ton)
TMHS 100 shown as part of Stroke length of 75 mm (3.0 in.)
hydraulic puller TMMA 100H Suitable for use with pullers with a 1 1/4"-12 UNF thread
TMHS 100:
Maximum withdrawal force of 100 kN (11.2 US ton)
Stroke length of 80 mm (3.1 in.)
Suitable for use with pullers with a 1 1/2"-16 UN thread
Technical data
Designation TMHS 75 TMHS 100
Contents 1 hydraulic spindle 1 hydraulic spindle
2 extension pieces; 3 extension pieces;
50 and 100 mm (2.0 and 3.9 in.) 50, 100 and 150 mm (2.0, 3.9 and 5.9 in.)
1 nosepiece 1 nosepiece
Maximum withdrawal force 75 kN (8.4 US ton) 100 kN (11.2 US ton)
Piston stroke 75 mm (3.0 in.) 80 mm (3.1 in.)
Body thread 1 1/4"-12 UNF 1 1/2"-16 UN
Nose piece diameter 35 mm (1.4 in.) 30 mm (1.2 in.)
Maximum reach 229 mm (9.0 in.) 390 mm (15.4 in.)
Weight 2,7 kg (6.0 lb) 4,5 kg (10.0 lb)
36
Efficient and correct dismounting
SKF Tri-section Pulling Plates TMMS series
The SKF TMMS series consists of five different sizes of tri-section
pulling plates suitable for shafts with diameters ranging from
50 to 380 mm (2 to 15 in.)
Suitable for use in combination with three-armed pullers
The plates grip behind the bearing inner ring, helping to ensure that
the pulling forces are only transmitted through the inner ring and not
through the outer ring or the rolling elements; thereby minimising the
risk of bearing damage
The tri-section construction allows an even dismounting force
distribution, preventing bearing locking and/or tilting on the shaft,
especially in the case of spherical roller and CARB toroidal roller
bearings
Special wedge shape design allows the plates to be easily inserted
between the bearing and the shoulder on the shaft
Dimensions
Designation d min d max A H
mm in. mm in. mm in. mm in.
TMMS 50 12 0.5 50 2.0 2030 0.81.2 15 0.6
TMMS 100 26 1.0 100 3.9 3655 1.42.1 25 1.0
TMMS 160 50 2.0 160 6.3 4573 1.82.9 30 1.2 A
37
For additional user safety during dismounting
SKF Puller Protection Blankets TMMX series
The SKF TMMX series are designed to offer additional user safety,
while dismounting bearings or other components
After the puller has been positioned, the blanket is simply wrapped
around the puller and application
The tough, transparent plastic allows the user to monitor the
component and the puller during operation
Especially designed to fit SKF TMMA series pullers, they are also
suitable for use in combination with many other pullers
Dimensions
Designation Recommended Length Width
maximum diameter
mm in. mm in. mm in.
TMMX 210 210 8.3 750 29.5 420 16.5
TMMX 280 280 11.0 970 38.2 480 18.9
TMMX 350 350 13.8 1 200 47.2 580 22.8
Technical data
Designation LGAF 3E
Specific gravity 1,19
Colour Whitebeige
Base oil type Mineral and synthetic
Thickener Lithium soap
Operating temperature range 25 to +150 C (13 to +302 F)
Base oil viscosity: 40 C, mm2/s 17,5
Available pack sizes 0,5 kg, 30 kg
38
SKF Anti Corrosive Agent LHRP 2
SKF LHRP 2 provides excellent long-term corrosion protection to ferrous and
non-ferrous surfaces. When applied, it creates a stable rust protection film on
the surface of the metal.
Technical data
Designation LHRP 2/5
Specific gravity 0,835
Colour Hazy brown
Base oil type Mineral
Flash point >62 C (>144 F)
Pour point <4 C (<39 F)
Available pack sizes 5l
YouTube channel
SKF has a large number of informative videos
available on YouTube. There you can find videos
that introduce you to new products and give you
instruction on how to use the products. In
addition, a comprehensive series of videos
explains the right techniques for mounting and
dismounting bearings of various types. The
videos are available with narration or subtitles in
various languages. The YouTube channel is an
easy way to learn more about SKF maintenance
and lubrication products. Just visit and subscribe
to be automatically informed when new videos
are added.
http://mapro.skf.com/youtube
39
Heating tools
Mounting Magnetic temperature probe, on the inner
ring, helps prevent bearing overheating
Its a fact.
Incorrect mounting methods account for up to 16% of premature bearing failures
To reduce the risk of incorrect mounting, SKF helped As a result, by using an SKF induction heater, the total cost
pioneer the use of portable induction heaters for bearing of ownership is often significantly lower. Ergonomics and
mounting applications in the 1970s. Since that time, there safety are also an important consideration for operators.
have been many advances in technology and SKF has been SKF induction heaters are equipped with design features
at the forefront in developing safer, more efficient and that make them easy to use and safe. Bearing support
user-friendly bearing induction heaters. arms reduce the risk of the bearing toppling during
heating, and ergonomically designed yokes help reduce
SKF Induction Heaters utilise advanced power electronics operator fatigue. In addition, the unique remote control
with application specific designs for high performance. enables the operator to control the heater at a safe
distance from the hot bearing, enhancing operator safety.
40
Features and benefits
The comprehensive SKF induction heater range can
be used for efficiently heating bearings and workpieces,
both large and small. Their innovative design offers
significant advantages to both owners and operators:
Advanced power electronics, with accurate electric current control, Induction coil located outside the heaters housing enables
help control the temperature rate increase a shorter heating time and lower energy consumption
Two step power setting option (50% / 100%), enables small bearings Foldable bearing support arms allow larger diameter bearings
to be heated safely and at a lower power consumption to be heated, and reduce the risk of the bearing toppling
For heating components other than bearings, all heaters are equipped during heating
with a heating time mode and for large components, optimized Magnetic temperature probe, combined with a temperature mode
TIH MB heaters for solid workpieces are available pre-set at 110 C (230 F), helps prevent bearing overheating
Thermal overheating protection reduces the risk of damage to the Unique SKF remote control, with operating display and control panel,
induction coil and electronics, enhancing reliability and safety makes the heater easy and safe to use
Automatic demagnetisation reduces the risk of ferrous debris Internal yoke storage, for smaller yoke(s), reduces the risk of yoke
contamination after heating damage or loss
Available in different voltage variants, to suit most operating voltages Integrated carrying handles allow for easy movement of the heater
worldwide in the workshop
Supplied with heat-resistant gloves for improved operator safety Sliding or swivel arm allows for easy and quick bearing
replacement, reducing operator fatigue (not for TIH 030m)
Induction heating has many advantages over other bearing heating methods
The use of an open flame to heat a bearing is not only inefficient and Ovens and hot plates are often used for batch heating of small bearings
uncontrolled, but often leads to bearing damage. This method should and this is an acceptable technique. However, for larger bearings, the use
not be used. of ovens and hotplates is generally quite inefficient and time consuming
and can present the operator with significant handling hazards.
Oil baths are sometimes used to heat bearings. Oil baths often take
a long time to reach the required temperature and can be difficult Induction heaters are the modern, efficient and safe way to
to control the actual bearing temperature. The energy consumption of heat bearings. In operation, they are generally faster, cleaner,
an oil bath is also significantly greater than using an induction heater. more controllable, and easier to use than other heating methods.
The risk of contaminating the bearing due to dirty oil is significant and
can lead to premature bearing failure. Handling hot, oily and slippery
bearings present significant hazards to the operator and great care must
be taken to avoid potential injuries.
41
Induction heaters
Portable, lightweight, high efficiency heater Compact lightweight design; just 21 kg Capable of heating a 97 kg (213 lb)
for bearings with an inner diameter ranging (46 lb), facilitating portability bearing in less than 20 minutes
from 20 to 100 mm (0.8 to 4 in.), and a Capable of heating a 28 kg (62 lb) Supplied standard with three yokes,
maximum weight of 5 kg (11 lb) bearing in just 20 minutes allowing bearings with a bore diameter
Equipped with temperature and time Supplied standard with three yokes, from 20 mm (0.8 in.) up to a maximum
control and automatic demagnetisation allowing bearings with a bore diameter from weight of 120 kg (264 lb) to be heated
Supplied in a carrying case 20 mm (0.8 in.) up to a maximum weight of Swivel arm for large size yoke
40 kg (90 lb) to be heated
kg
5 30 40 100 120 220 300 700 1 200
1) For heating components other than bearings, SKF recommends consideration of TIH L MB series heater. Contact SKF to help you select a suitable induction heater for your application.
42
TIH 220m TIH L series
Large induction heater with a 300 kg bearing Extra large induction heater with a 1 200 kg
heating capacity bearing heating capacity
Capable of heating a 220 kg (480 lb) bearing in just Using just 20 kVA of electrical power, the TIH L series can
20 minutes heat large bearings up to 1 200 kg (2 600 lb)
Supplied standard with two yokes, allowing bearings Bearings and work pieces can be heated vertically or horizontally
with a bore diameter from 60 mm (2.3 in.) up to a Compact design allows the TIH L series heaters to be easily
maximum weight of 300 kg (660 lb) to be heated transported by forklift
Sliding arm for large size yoke Available with two different operating areas
TIH L33
43
Technical data
Designation TMBH 1 TIH 030m TIH 100m TIH 220m
Max. bearing weight 5 kg (11 lb) 40 kg (88 lb) 120 kg (264 lb) 300 kg (662 lb)
Bore diameter range 20100 mm (0.84 in.) 20300 mm (0.811.8 in.) 20400 mm (0.815.7 in.) 60600 mm (2.323.6 in.)
Operating area (w h) 52 52 mm (2 2 in.) 100 135 mm (3.9 5.3 in.) 155 205 mm (6.1 8 in.) 250 255 mm (9.8 10 in.)
Coil diameter N/A 95 mm (3.7 in.) 110 mm (4.3 in.) 140 mm (5.5 in.)
Standard yokes (included) 20 mm (0.8 in.) 65 mm (2,6 in.) 80 mm (3.1 in.) 100 mm (3.9 in.)
to suit bearing/workpiece 40 mm (1.6 in.) 40 mm (1.6 in.) 60 mm (2.3 in.)
minimum bore diameter 20 mm (0.8 in.) 20 mm (0.8 in.)
Application example
(bearing, weight, 6310, 23136 CC/W33, 23156 CC/W33, 23172 CC/W33,
temperature, time) 1,07 kg, 110 C, 1m 45s 28 kg, 110 C, 20m 97 kg, 110 C, 20m 220 kg, 110 C, 20m
Max. power consumption 0,35 kVA 2,0 kVA 3,6 kVA (230 V) 10,011,5 kVA (400460 V)
4,04,6 kVA (400460 V)
Voltage 1)
100240V/5060Hz TMBH 1
100120V/5060Hz TIH 030m/110V
200240V/5060Hz TIH 030m/230V TIH 100m/230V TIH 220m/LV
400460V/5060Hz TIH 100m/MV TIH 220m/MV
Temperature control 2) 0 to 200 C (32 to 392 F) 20 to 250 C (68 to 482 F) 20 to 250 C (68 to 482 F) 20 to 250 C (68 to 482 F)
Demagnetisation according N/A <2 A/cm <2 A/cm <2 A/cm
to SKF norms
Dimensions (w d h) 330 150 150 mm 460 200 260 mm 570 230 350 mm 750 290 440 mm
(13 5.9 5.9 in.) (18.1 7.9 10.2 in.) (22.4 9 13.7 in.) (29.5 11.4 17.3 in.)
Clamp: 115 115 31 mm
(4.5 4.5 1.2 in.)
Total weight (incl. yokes) 4,5 kg (10 lb) 20,9 kg (46 lb) 42 kg (92 lb) 86 kg (189 lb)
1) Some special voltage versions (e.g. 575V, 60 Hz CSA ready) are available for specific countries. For additional information, please contact your local SKF authorised distributor.
2) Maximum heating temperature capacity depends on the weight and geometry of the bearing or workpiece. The heaters can achieve higher temperatures, please contact SKF for advice.
44
Solid workpiece heaters
The SKF TIH L MB series is specially designed to heat solid workpieces, such as rings, sleeves,
gears, couplings, bushings and pulleys, as well as train wheels, tires or similar components.
Featuring one magnetic coil in the center, these powerful and durable heaters localize the
heating in the workpiece bore for superior performance on solid components.
Simple and safe operation with remote-control and power level selection
Superior heating performance for solid workpieces with low energy consumption
Quick and easy placement of solid components with sliding yoke
Automatic demagnetization reduces risk of ferrous debris contamination
Easy to transport using standard forklift
Available in three voltage variants to suit most operating voltages worldwide
Available with three different operating areas
45
Technical data
Designation TIH L33MB TIH L44MB TIH L77MB
Maximum workpiece weight 350 kg (772 lb) 600 kg (1 323 lb) 600 kg (1 323 lb)
Bore diameter range 115700 mm (4.527.6 in.) 150800 mm (5.931.5 in.) 150800 mm (5.931.5 in.)
Operating area (w h) 330 320 mm (13.0 12.6 in.) 465 492mm (18.3 19.4 in.) 765 792mm (30.1 31.2 in.)
Coil diameter 150 mm (5.9 in.) 175 mm (6.9 in.) 175 mm (6.9 in.)
Standard yokes (included) to suit
workpiece minimum bore diameter 115 mm (4.5 in.) 150 mm (5.9 in.) 150 mm (5.9 in.)
Max. power consumption TIH L33MB/MV: 15 kVA TIH L44MB/LV: 2024 kVA TIH L77MB/LV: 2024 kVA
TIH L33MB/LV: 15 kVA TIH L44MB/MV: 2023 kVA TIH L77MB/MV: 2023 kVA
Voltage 1)
200240V/5060Hz TIH L33MB/LV TIH L44MB/LV TIH L77MB/LV
400460V/5060Hz TIH L33MB/MV TIH L44MB/MV TIH L77MB/MV
Temperature control 0250 C (32482 F); in steps of 1 0250 C (32482 F); in steps of 1 0250 C (32482 F); in steps of 1
Time control 0120 minutes; in steps of 0120 minutes; in steps of 0120 minutes; in steps of
0,1 minute 0,1 minute 0,1 minute
Demagnetisation according
to SKF norms <2A/cm <2A/cm <2A/cm
Maximum heating temperature 2) 250 C (482 F) 250 C (482 F) 250 C (482 F)
Dimensions (w d h) 400 743 550 mm 1 200 600 850 mm 1 320 600 1 150 mm
(15.8 29.3 21.7 in.) (47.3 23.6 33.5 in.) (52 23.6 45.3 in.)
Weight 140 kg (309 lb) 324 kg (714 lb) 415 kg (915 lb)
1) Some special voltage versions (e.g. 575V, 60Hz CSA ready) are available for specific countries. For additional information, please contact your local SKF authorised distributor.
2) Depending on bearing or workpiece weight. For higher temperatures, please contact SKF.
In just three easy steps, you can define your heating application and receive a list
of all suitable heaters for that application, including a recommendation of the
heater that offers the best price-performance ratio.
The online heater selection tool is available free of charge, just scan the QR code
or visit us on www.mapro.skf.com/heaterselect
The heater selection tool supports all mounting and fixed size EAZ dismounting
heaters and offers additional information such as the product data sheet,
technical data and product websites for each heater. If you cannot find the right
heater for your application or you need more information, please dont hesitate to
contact SKF.
www.mapro.skf.com/heaterselect
46
A unique and flexible heating solution for very large
bearings and workpieces
Multi-core induction heaters, TIH MC series
The SKF multi-core induction heaters are energy efficient, custom-made
heating solutions. Compared to other heating methods, they often can
significantly save heating time.
Technical data
Designation 729659 C
729659 C/110V
Voltage 729659 C 230 V (50/60 Hz) Height of cover 50 mm (2 in.)
729659 C/110 V 115 V (50/60 Hz)
Overall dimensions 390 240 140 mm
Power 1 000 W (l w h) (15.4 9.5 5.5 in.)
Temperature range 50200 C (120390 F) Weight 4,7 kg (10 lb)
Plate dimensions (l w) 380 178 mm (15 7 in.)
47
Dismounting
SKFs range of heating equipment enables quick and safe dismounting of cylindrical roller bearing inner rings
and covers a wide range of applications. Aluminium heating rings TMBR series are designed for dismounting
inner rings of small and medium-size cylindrical roller bearings. Adjustable and fixed induction heaters
EAZ series are suitable for frequent dismounting of various sizes of cylindrical roller bearing inner rings.
They are available for all bearing sizes of the NU, NJ and NUP series.
These series are bearings without flanges or with only one flange on the
inner ring. The rings are available as standard for the following bearing
sizes: 204 to 252, 304 to 340, 406 to 430.
Technical data
Designation TMBR Bearing designation; (e.g. TMBR NU216E)
Material Aluminium
Maximum temperature 300 C (572 F)
Fixed size EAZ heaters are customised SKF Induction Heaters for dismounting cylindrical roller bearing inner rings. Please contact SKF to assist you in finding an EAZ heater that suits
your application. EAZ heaters are supplied without a control cabinet. SKF control cabinets are required to operate the fixed size EAZ heater and can be ordered separately.
48
Safe and easy bearing removal in just 3 minutes
SKF Fixed Induction Heater EAZ series
The fixed size EAZ induction heaters are designed to safely and easily dismount
cylindrical roller bearing inner rings, which are often mounted with a very tight
interference fit.
Heating the inner ring rapidly loosens the fit, as the shaft remains cool, enabling
the ring to be removed without causing damage to the shaft or inner ring. With
easy-to-use fixed size EAZ induction heaters, three minutes are usually enough
time to professionally dismount cylindrical roller bearing inner rings or similar
components.
Control cabinets from SKF provide the necessary power to run fixed size
EAZ heaters and are available with various voltages to operate EAZ heaters
in almost any country. Special versions of the control cabinets are available
that enable up to three EAZ heaters to be used simultaneously
In light section mills, rod wire mills or railway applications, EAZ heaters can
often dismount cylindrical roller bearing inner rings with one or more rows
of rollers or multiple inner rings at the same time
EAZ induction heaters can also be used to dismount non-bearing elements
like sleeves or rings
Control cabinet
Add corresponding cabinet version to the designation when ordering (e.g. SSD C350B).
Please, add corresponding F dimension as a suffix to the designation when ordering Add corresponding control cabinet voltage and frequency code as a suffix to the
(e.g. EAZ F312MV). designation when ordering (e.g. SSD C350B).
49
For frequent dismounting of cylindrical roller bearings
SKF Adjustable Induction Heaters EAZ series
The SKF EAZ 80/130 and EAZ 130/170 are used for frequent dismounting of
cylindrical bearing inner rings. Where inner rings are removed infrequently,
aluminium heating rings, SKF TMBR series, are also available. For larger
cylindrical inner rings normally found in steel mill applications, SKF can supply
special EAZ induction heaters.
For bearings NU
EAZ 80/130 213221 313320 412418 10141022 22132220 23132320
EAZ 130/170 222228 321326 419424 10241030 22222228 23222326
Ordering designations
Designation Power supply Current Designation Power supply Current
EAZ 80/130A 2 230 V/50 Hz 40 A EAZ 130/170D 3 230 V/50 Hz 43 A
EAZ 80/130B 2 400 V/50 Hz 45 A EAZ 130/170E 3 400 V/50 Hz 35 A
EAZ 80/130C 2 460 V/60 Hz 25 A EAZ 130/170F 3 460 V/60 Hz 23 A
EAZ 80/130D 2 415 V/50 Hz 35 A EAZ 130/170G 3 420 V/60 Hz 30 A
EAZ 130/170A 2 230 V/50 Hz 60 A EAZ 130/170H 3 415 V/50 Hz 30 A
EAZ 130/170B 2 400 V/50 Hz 45 A
Dimensions
Designation EAZ 80/130 EAZ 130/170
Connection cable 5 m (16 ft) 5 m (16 ft)
Dimensions a 134 mm (5.3 in.) 180 mm (7.1 in.) b
b 50 mm (2.0 in.) 50 mm (2.0 in.)
c 80 ... 132 mm (3.1... 5.2 in.) 130 ... 172 mm (5.1 ... 6.8 in.)
Weight 28 kg (62 lb) 35 kg (77 lb)
c
H
50
Accessories
For safe handling of heated components up to 150 C (302 F)
SKF Heat Resistant Gloves TMBA G11
The SKF TMBA G11 are specially designed for the handling of heated bearings.
Technical data
Lint free
Designation TMBA G11 Heat resistant up to 150 C (302 F)
Material Hytex Cut resistant
Inner lining Cotton Tested and certified for mechanical risks
Size 9 (EN 388) and thermal risks (EN 407)
Colour White
Maximum
temperature 150 C (302 F)
Pack size 1 pair
51
Mounting and dismounting bearings
using hydraulic techniques
SKF invented hydraulic techniques for mounting bearings in the 1940s. Since then,
the SKF hydraulic methods have been further developed to become the preferred
mounting methods for larger bearings as well as other components. These techniques
have helped to simplify bearing arrangements and facilitate correct and easy
mounting. Using SKF hydraulic techniques for bearing dismounting reduces the risk
of damaging the bearing or its seating. Additionally, greater withdrawal forces can be
applied with less effort and maximum control, allowing quick and safe dismounting.
With the SKF hydraulic mounting and dismounting techniques, you can achieve:
52
Mounting Dismounting
Tapered shafts Cylindrical shafts Tapered shafts
53
SKF Drive-up Method
Accurate mounting of SKF spherical roller and CARB
toroidal roller bearings on tapered seatings.
The SKF Drive-up Method is a well-proven method, unique to SKF, of accurately achieving the
adjustment of SKF spherical roller and CARB toroidal roller bearings mounted on tapered seatings.
The method incorporates the use of an SKF HMV ..E hydraulic nut fitted with a dial indicator, and a
high accuracy digital pressure gauge, mounted on the selected pump.
The correct fit is achieved by controlling the axial drive-up of the bearing from a pre-determined
starting position, defined by the pressure in the SKF HMV..E hydraulic nut. The second stage is
monitored by driving the bearing up a calculated distance on the taper seating.
The starting position pressure and the drive-up distance for many SKF bearings can be
determined by using the SKF Drive-up Method PC program, available at skf.com or by
downloading the iOS or Andoid app for smartphones and tablets. In addition, SKFs unique
information service for mounting and dismount bearings, skf.com/mount, also features
the SKF Drive-up Method.
Note: All above pumps are supplied complete with digital pressure gauge, high pressure hose and quick connect coupling.
54
Step by step procedure
One sliding surface 1. Determine whether one or two surfaces slide during mounting;
see figures.
2. Lightly oil all mating surfaces with a thin oil, e.g. SKF LHMF 300, and carefully
place the bearing on the shaft.
3. Use the SKF Drive-up Method PC program or app or use skf.com/mount to
calculate the required values for the bearing and the mounting arrangement.
4. Drive the bearing up to the starting position by applying the required hydraulic
nut pressure. Monitor the pressure using the gauge on the selected pump.
SKF Hydraulic Pump 729124 DU is suitable for SKF Hydraulic Nuts HMV
54E. SKF TMJL 100DU is suitable for SKF Hydraulic Nuts HMV 92E while
SKF TMJL 50DU is suitable for nuts HMV 200E. As an alternative, the digital
pressure gauge THGD100 can be screwed directly into the hydraulic nut.
5. Drive the bearing up the taper by the required distance Ss.
The axial drive-up is best monitored by a dial indicator.
The SKF Hydraulic Nut HMV ..E is prepared for dial indicators. Normally,
Two sliding surfaces the bearing is now mounted with a suitable interference on the shaft and
a suitable residual clearance.
A3
A1 A2
Ss
S
A1 Zero position
A2 Starting position
Patent protected A3 Final position
The adapter can be used with nuts from size SKF HMV(C) 42 to HMV(C) 200.
The adapter is not required for the current generation of SKF HMV(C) ..E nuts.
One adapter suits the previous generation nuts from
SKFHMV(C)42 up to 200
Rugged construction
Easy to attach to the SKF HMV nut using strong magnets
Used in conjunction with SKF dial indicators
55
Hydraulic nuts
Easy application of high drive-up forces
Hydraulic Nuts HMV ..E series
Mounting bearings on tapered seatings can be a difficult and time-consuming
job. Using an SKF Hydraulic Nut facilitates easy and quick application of the
high drive-up forces required for mounting bearings. Dismounting bearings
mounted on either adapter or withdrawal sleeves is also often a difficult and
time-consuming job. These problems can be reduced with the use of an SKF
Hydraulic Nut. Oil is pumped into the nut and the piston is pushed out with a
force, which is sufficient to free the sleeve. All SKF HMV ..E nuts are supplied
with a quick connection coupling to fit the SKF hydraulic pumps.
56
Mounting
HMV ..E nut for driving the HMV ..E nut screwed onto the HMV ..E nut for driving the HMV ..E nut and special stop
bearing onto a tapered seating. shaft for driving in a withdrawal bearing onto an adapter sleeve. nut for driving in a withdrawal
sleeve. sleeve.
Dismounting
HMV ..E nut and stop ring in position HMV ..E nut used to free a
to press an adapter sleeve free. withdrawal sleeve.
57
Ordering details and dimensions HMV E series (metric)
Designation G d1 d2 d3 B B1 Permitted Piston Weight
piston area
displacement
thread mm mm mm mm mm mm mm2
HMV 34E M1703 170,5 235 244 41 7 6 9 400 8,40
HMV 36E M1803 180,5 247 256 41 7 6 10 300 9,15
HMV 38E M1903 191 259 270 42 8 7 11 500 10,5
HMV 40E M2003 201 271 282 43 8 8 12 500 11,5
HMV 41E Tr2054 207 276 288 43 8 8 12 800 12,0
HMV 42E Tr2104 212 282 294 44 8 9 13 400 12,5
HMV 43E Tr2154 217 287 300 44 8 9 13 700 13,0
HMV 44E Tr2204 222 293 306 44 8 9 14 400 13,5
HMV 45E Tr2254 227 300 312 45 8 9 15 200 14,5
HMV 46E Tr2304 232 305 318 45 8 9 15 500 14,5
HMV 47E Tr2354 237 311 326 46 8 10 16 200 16,0 B
HMV 48E Tr2404 242 316 330 46 9 10 16 500 16,0
G1/4 B1
HMV 50E Tr2504 252 329 342 46 9 10 17 600 17,5
HMV 52E Tr2604 262 341 356 47 9 11 18 800 19,0
HMV 54E Tr2704 272 352 368 48 9 12 19 800 20,5
HMV 56E Tr2804 282 363 380 49 9 12 21 100 22,0
HMV 58E Tr2904 292 375 390 49 9 13 22 400 22,5
HMV 60E Tr3004 302 386 404 51 10 14 23 600 25,5
d3 G d1 d2
HMV 62E Tr3105 312 397 416 52 10 14 24 900 27,0
HMV 64E Tr3205 322 409 428 53 10 14 26 300 29,5
HMV 66E Tr3305 332 419 438 53 10 14 27 000 30,0
HMV 68E Tr3405 342 430 450 54 10 14 28 400 31,5
HMV 69E Tr3455 347 436 456 54 10 14 29 400 32,5
HMV 70E Tr3505 352 442 464 56 10 14 29 900 35,0
HMV 72E Tr3605 362 455 472 56 10 15 31 300 35,5
HMV 73E Tr3655 367 460 482 57 11 15 31 700 38,5
HMV 74E Tr3705 372 466 486 57 11 16 32 800 39,0
HMV 76E Tr3805 382 476 498 58 11 16 33 500 40,5
HMV 77E Tr3855 387 483 504 58 11 16 34 700 41,0
HMV 80E Tr4005 402 499 522 60 11 17 36 700 45,5
HMV 82E Tr4105 412 510 534 61 11 17 38 300 48,0
HMV 84E Tr4205 422 522 546 61 11 17 40 000 50,0
HMV 86E Tr4305 432 532 556 62 11 17 40 800 52,5
HMV 88E Tr4405 442 543 566 62 12 17 42 500 54,0
HMV 90E Tr4505 452 554 580 64 12 17 44 100 57,5
HMV 92E Tr4605 462 565 590 64 12 17 45 100 60,0
HMV 94E Tr4705 472 576 602 65 12 18 46 900 62,0
HMV 96E Tr4805 482 587 612 65 12 19 48 600 63,0
HMV 98E Tr4905 492 597 624 66 12 19 49 500 66,0
HMV 100E Tr5005 502 609 636 67 12 19 51 500 70,0
HMV 102E Tr5106 512 624 648 68 12 20 53 300 74,0
HMV 104E Tr5206 522 634 658 68 13 20 54 300 75,0
HMV 106E Tr5306 532 645 670 69 13 21 56 200 79,0
HMV 108E Tr5406 542 657 682 69 13 21 58 200 81,0
HMV 110E Tr5506 552 667 693 70 13 21 59 200 84,0
HMV 112E Tr5606 562 678 704 71 13 22 61 200 88,0
HMV 114E Tr5706 572 689 716 72 13 23 63 200 91,0
HMV 116E Tr5806 582 699 726 72 13 23 64 200 94,0
HMV 120E Tr6006 602 721 748 73 13 23 67 300 100
HMV 126E Tr6306 632 754 782 74 14 23 72 900 110
HMV 130E Tr6506 652 775 804 75 14 23 76 200 115
HMV 134E Tr6706 672 796 826 76 14 24 79 500 120
HMV 138E Tr6906 692 819 848 77 14 25 84 200 127
HMV 142E Tr7107 712 840 870 78 15 25 87 700 135
HMV 150E Tr7507 752 883 912 79 15 25 95 200 146
HMV 160E Tr8007 802 936 965 80 16 25 103 900 161
HMV 170E Tr8507 852 990 1 020 83 16 26 114 600 181
HMV 180E Tr9007 902 1 043 1 075 86 17 30 124 100 205
HMV 190E Tr9508 952 1 097 1 126 86 17 30 135 700 218
HMV 200E Tr10008 1 002 1 150 1 180 88 17 34 145 800 239
58
Technical data HMVC E series (inch)
Designation HMVC E
Thread form
HMVC 10E HMVC 64E American National Form Threads Class 3
HMVC 68E HMVC 190E ACME General Purpose Threads Class 3 G
Mounting fluid LHMF 300
Recommended pumps
HMVC 10E HMVC 52E 729124 / TMJL 100 / 728619 E / TMJL 50
HMVC 56E HMVC 92E TMJL 100 / 728619 E / TMJL 50
HMVC 94E HMVC 190E 728619 E / TMJL 50
Quick connection nipple 729832 A (included)
Other types available
Inch series nuts HMVC E series
Nuts without threads HMV...E/A101
59
Ordering details and dimensions HMVC E series (inch)
Designation Pitch Threads Permitted Piston Weight
diameter piston area
displacement
G d1 d2 d3 B B1
in. in. in. in. in. in. in. in. in.2 lb
HMVC 106E 20.867 20.7220 4 20.9 25.4 26.4 2.7 0.51 0.83 87.1 174
HMVC 112E 22.048 21.9030 4 22.1 26.7 27.7 2.8 0.51 0.87 94.9 194
HMVC 120E 23.623 23.4780 4 23.7 28.4 29.4 2.9 0.51 0.91 104.3 220
HMVC 126E 24.804 24.6590 4 24.9 29.7 30.8 2.9 0.55 0.91 113.0 243
HMVC 134E 26.379 26.2340 4 26.5 31.3 32.5 3.0 0.55 0.94 123.2 265
HMVC 142E 27.961 27.7740 3 28.0 33.1 34.3 3.1 0.59 0.98 135.9 298
HMVC 150E 29.536 29.3490 3 29.6 34.8 35.9 3.1 0.59 0.98 147.6 322
HMVC 160E 31.504 31.3170 3 31.6 36.9 38.0 3.1 0.63 0.98 161.0 355
HMVC 170E 33.473 33.2860 3 33.5 39.0 40.2 3.3 0.63 1.02 177.6 399
HMVC 180E 35.441 35.2540 3 35.5 41.1 42.3 3.4 0.67 1.18 192.4 452
HMVC 190E 37.410 37.2230 3 37.5 43.2 44.3 3.4 0.67 1.18 210.3 481
60
Hydraulic pump and oil injector selection guide
Selection guide
Max. working Oil container Connection
pressure Pump Type capacity nipple Application examples 1)
30 MPa (4 350 psi) THAP 030E Air-driven pump Separate container G 3/4 SKF OK Coupling hydraulic chamber
50 MPa (7 250 psi) TMJL 50 Hand operated pump 2 700 cm3 (165 in.3) G 1/4 All HMV ..E (dismounting with sleeves only)
SKF OK Coupling hydraulic chamber
100 MPa (14 500 psi) 729124 Hand operated pump 250 cm3 (15 in.3) G 1/4 HMV 54E (dismounting with sleeves only)
Oil injection for small bearings
TMJL 100 Hand operated pump 800 cm3 (48 in.3) G 1/4 HMV 92E (dismounting with sleeves only)
Oil injection for medium bearings
150 MPa (21 750 psi) THAP 150E Air-driven pump Separate container G 3/4 Bolt tensioners, propellers
Oil injection for large bearing seatings
728619 E Hand operated pump 2 550 cm3 (155 in.3) G 1/4 All HMV ..E nuts (dismounting with sleeves only)
Oil injection for bearing seatings
300 MPa (43 500 psi) THAP 300E Air-driven oil injector Separate container G 3/4 OK Couplings
Large pressure joints
Oil injection for large gears and railway wheels
729101/ Oil injection kit 200 cm3 (12.2 in.3) Several OK Couplings
300MPA Oil injection for gears and railway wheels
Pressure joints
Complete kit suitable for many applications
THKI 300 Oil injection set 200 cm3 (12.2 in.3) Several Oil injection for gears and railway wheels
Pressure joints
Complete set suitable for many applications
400 MPa (58 000 psi) THAP 400E Air-driven oil injector Separate container G 3/4 OK Couplings
Large pressure joints
Oil injection for large gears and railway wheels
226400 E/400 Hand operated 200 cm3 (12.2 in.3) G 3/4 OK Couplings
oil injector Oil injection for gears and railway wheels
Pressure joints
729101/ Oil injection kit 200 cm3 (12.2 in.3) Several OK Couplings
400MPA Oil injection for gears and railway wheels
Pressure joints
Complete kit suitable for many applications
THKI 400 Oil injection set 200 cm3 (12.2 in.3) Several Oil injection for gears and railway wheels
Pressure joints
Complete set suitable for many applications
1) The interference it and application size may mean that a pump / injector with a higher pressure and/or container volume is required.
62 62 63 63
64 65 65 66
61
Hydraulic pumps
Applications Applications
SKF OK Coupling hydraulic chambers SKF Hydraulic Nuts HMV 54E
All sizes SKF Hydraulic Nuts Oil injection applications where the maximum pressure
Oil injection applications where the maximum pressure is 100 MPa (14 500 psi)
is 50 MPa (7 250 psi) For applications where space does not permit the use of a quick
connect coupling and nipple, such as AOH sleeves, a special pump
design is available (SKF 729124 A)
Technical data
Designation TMJL 50 729124 TMJL 100 728619 E
Maximum pressure 50 MPa (7 250 psi) 100 MPa (14 500 psi) 100 MPa (14 500 psi) 150 MPa (21 750 psi)
Oil container capacity 2 700 cm3 (165 in.3) 250 cm3 (15 in.3) 800 cm3 (48 in.3) 2 550 cm3 (155 in.3)
Volume/stroke 3,5 cm3 (0.21 in.3) 0,5 cm3 (0.03 in.3) 1,0 cm3 (0.06 in.3) 1st stage: 20 cm3 below 2,5 MPa
(1.2 in.3 below 362 psi)
2nd stage: 1 cm3 above 2,5 MPa
(0.06 in.3 above 362 psi)
Length of pressure hose fitted 3 000 mm (118 in.) 1 500 mm (59 in.) 3 000 mm (118 in.) 3 000 mm (118 in.)
with quick connection coupling
Connection nipple (included) G 1/4 quick connection G 1/4 quick connection G 1/4 quick connection G 1/4 quick connection
Weight 12 kg (26 lb) 3,5 kg (8 lb) 13 kg (29 lb) 11,4 kg (25 lb)
All SKF Hydraulic Pumps are filled with SKF Mounting Fluid and are supplied with an extra litre of fluid.
62
Large oil container 100 MPa (14 500 psi) 150 MPa (21 750 psi)
SKF Hydraulic Pump TMJL 100 SKF Hydraulic Pump 728619 E
The SKF TMJL 100 pump is mainly intended for use The SKF 728619 E is a two-stage pump suitable for
with hydraulic nuts ( HMV 92E) to mount bearings or use with SKF Supergrip Bolts and to mount bearings
components where a maximum pressure of 100 MPa or components where a maximum pressure of 150 MPa
(14 500 psi) is required. (21 750 psi) is required.
Oil container capacity 800 cm3 (48 in.3) Oil container capacity 2 550 cm3 (155 in.3)
Fitted with a pressure gauge Two stage pressure pumping
Packed in a sturdy protective case Fitted with a pressure gauge
Packed in a sturdy protective case
Applications
SKF Hydraulic Nuts HMV 92E Applications
Oil injection applications where the maximum pressure SKF Supergrip Bolts
is 100 MPa (14 500 psi) Oil injection applications where the maximum pressure
Suitable with SKF Hydraulic Assisted Pullers TMHP series is 150 MPa (21 750 psi)
All sizes SKF Hydraulic Nuts
SKF mounting and dismounting fluids are suitable for use with
SKFhydraulic equipment, including hydraulic pumps, HMV ..E nuts
and oil injection tools in mounting and dismounting jobs. All SKF
LHMF 300 LHDF 900 Hydraulic Pumps are filled with SKF Mounting Fluid LHMF 300 and
are supplied with an extra litre of fluid.
63
Oil Injectors
To enable the SKF Oil Injection Method to be used, a range of oil
injectors, kits and sets are available. Depending on the model chosen,
working pressures up to 400 MPa (58 000 psi) can be achieved.
In addition, a comprehensive range of high pressure accessories such
as pipes, connection nipples, extension pipes and plugs permit the
use of SKF Oil Injectors for many different applications.
Technical data
Designation 226400 E 226400 E/400 THKI 300 THKI 400
729101/300MPA 729101/400MPA
Maximum pressure 300 MPa 400 MPa 300 MPa 400 MPa
(43 500 psi) (58 000 psi) (43 500 psi) (58 000 psi)
Volume per stroke 0,23 cm3 0,23 cm3 0,23 cm3 0,23 cm3
(0.014 in.3) (0.014 in.3) (0.014 in.3) (0.014 in.3)
Oil reservoir capacity 200 cm3 200 cm3 200 cm3 200 cm3
(12.2 in..3) (12.2 in.3) (12.2 in.3) (12.2 in.3)
Connecting threads G 3/4 G 3/4 G 3/4 G 3/4
64
300 and 400 MPa (43 500 and 58 000 psi) 300 and 400 MPa (43 500 and 58 000 psi)
SKF Oil Injection Kits 729101 series SKF Oil Injection Set THKI series
The 729101 series of SKF Oil Injection Kits are suitable The SKF THKI series is used for the mounting and
for many applications using the SKF Oil Injection Method. dismounting of pressure joints of all sizes and applications
Each kit contains an SKF Oil Injector complete with a high such as rolling bearings, couplings, gears, flywheels
pressure pipe, pressure gauge, adapter block and a range and railway wheels. The set consists of a stand-mounted
of connection nipples. oil injector complete with a high pressure pipe, pressure
gauge and a range of connection nipples.
Injector can be used directly on the application or by connecting
to the accessories provided Designed to be especially suitable for workshop use
All items packed in a sturdy, compact carrying case especially When the pressure is released, the unused oil is automatically
suitable for field use returned to the reservoir, minimizing the risk of oil leakage to
When the pressure is released, the unused oil is automatically the environment
returned to the reservoir, minimizing the risk of oil leakage to Oil container capacity 200 cm3 (12.2 in.3)
the environment Can be used for applications requiring a maximum pressure
Oil container capacity 200 cm3 (12.2 in.3) of up to 400 MPa (58 000 psi)
Contents list
Designation 729101/300MPA 729101/400MPA THKI 300 THKI 400
Oil injector 226400 E 226400 E/400 THKI 300 THKI 400
Adapter block 226402 226402 227957 A 227957 A/400 MP
Pressure gauge 1077589 1077589/3 1077589 1077589/3
High pressure pipe (G 3/4 1/4) 227957 A 227957 A/400 MP 227957 A 227957 A/400 MP
Connection nipple (G 1/4 1/8) 1014357 A 1014357 A
Connection nipple (G 1/4 1/2) 1016402E 1016402E 1016402E 1016402E
Connection nipple (G 1/4 3/4) 228027E 228027E 228027E 228027E
Mounting fluid LHMF 300/1 LHMF 300/1
Carrying case Yes Yes Yes Yes
65
Air-driven hydraulic pumps and injectors
30, 150, 300 and 400 MPa (4 350, 21 750, 43 500 and 58 000 psi)
SKF Air-driven Hydraulic Pumps and Oil Injectors, THAP E series
The THAP E air-driven hydraulic pumps and oil injectors are available in four different
pressure versions. They can be used for mounting OK Couplings, large pressure joints
such as bearings, flywheels, couplings and railway wheels. The THAP E unit consists
of a hydraulic pump or high pressure oil injector, driven by an air motor.
The units are supplied in a sturdy case including oil suction and return
hoses with quick connect couplings. The units can also be supplied in
complete sets, consisting of a THAP E and such accessories as a pressure
gauge, high pressure pipe or pressure hose.
Applications
SKF OK Couplings
Mounting bearings
Mounting ship propellers, rudder pintles, THAP E/SK1
railway wheels and other similar applications
THAP E
Technical data
Designation THAP 030E THAP 150E THAP 300E THAP 400E
Nominal hydraulic pressure 30 MPa (4 350 psi) 150 MPa (21 750 psi) 300 MPa (43 500 psi) 400 MPa (58 000 psi)
Operating air pressure 1) 7 bar (101.5 psi) 7 bar (101.5 psi) 7 bar (101.5 psi) 7 bar (101.5 psi)
Volume/stroke 10 cm3 (0.61 in. 3) 1,92 cm3 (0.12 in. 3) 0,83 cm3 (0.05 in. 3) 0,64 cm3 (0.039 in. 3)
Oil outlet G 3 /4 G 3/4 G 3/4 G 3 /4
Length 350 mm (13.9 in.) 350 mm (13.9 in.) 405 mm (16 in.) 405 mm (16 in.)
Height 202 mm (8 in.) 202 mm (8 in.) 202 mm (8 in.) 202 mm (8 in.)
Width 171 mm (6.7 in.) 171 mm (6.7 in.) 171 mm (6.7 in.) 171 mm (6.7 in.)
Weight 11,5 kg (25.3 lb) 11,5 kg (25.3 lb) 13 kg (28.6 lb) 13 kg (28.6 lb)
1) Air pressures above 7 bar are automatically limited to 7 bar by an internal air limiter.
66
100 to 400 MPa (14 500 to 58 000 psi)
SKF Pressure Gauges
SKF Pressure Gauges are designed to fit SKF Hydraulic Pumps and SKF Oil
Injectors. The gauges are all liquid filled and/or equipped with a restriction
screw in order to absorb any sudden pressure drop thereby preventing
damage. Safety glass and blowout discs are standard for all gauges and all
have dual scales (MPa/psi).
Technical data
Designation Pressure range Diameter (H) Connection Weight Accuracy
thread
MPa psi mm in. kg lb % of full scale
1077587 0100 014 500 110 4.33 G 1/2 1,00 2.2 1
1077587/2 0100 014 500 69 2.72 G 1/4 0,25 0.6 1,6
THGD 100 1) 0100 015 000 79 3.10 G 1/4 0,54 1.2 0,1 H
1077589 0300 043 500 110 4.33 G 1/2 1,00 2.2 1
1077589/3 0400 058 000 110 4.33 G 1/2 1,00 2.2 1
67
Accessories
Flexible solutions to connect oil injection equipment
SKF High-pressure Pipes
The range of SKF High pressure pipes can be used when SKF Oil Injection
equipment cannot be connected directly to a pressure joint. They consist of a
steel pipe with a steel ball fitted to both ends. Two swivelling connection
nipples press these balls against the seating of the connecting hole and seal
against oil leakage.
Technical data
Designation Dimensions Weight
G G1 A A1 Dw Dw1 L
mm in. mm in. mm in. mm in. mm in. kg lb
721740 A G 1/8 G 3/4 11,5 0.45 36,9 1.45 7,94 0.31 15,88 0.63 1 000 39 0,3 0.7
227957 A 1) G 1/4 G 3/4 17,3 0.68 36,9 1.45 11,11 0.44 15,88 0.63 2 000 78 0,4 0.9
227958 A 1) G 3/4 G 3/4 36,9 1.45 36,9 1.45 15,88 0.63 15,88 0.63 2 000 78 0,6 1.3
1020612 A 2) G 1/4 G 1/4 17,3 0.68 17,3 0.68 11,11 0.44 11,11 0.44 1 000 39 0,5 1.1
728017 A G 1/4 G 1/4 17,3 0.68 17,3 0.68 11,11 0.44 7,94 0.31 300 12 0,2 0.4
Pipe lengths Between 300 mm (12 in.) and 4 000 mm (157 in.)
can be ordered e.g. 227957A/3000 (3 000 mm long)
1) These pipes are also available with a maximum working pressure of 400 MPa (58 000 psi).
Designations are 227957 A/400MP and 227958 A/400MP. Outer diameter of the pipe is 6 mm (0.24 in.)
2) Maximum working pressure 400 MPa (58 000 psi). Outer diameter of the pipe 6 mm (0.24 in.).
Safety note:
For safety reasons, these high-pressure pipes have a maximum service life.
All SKF high pressure pipes are hard-marked with the year in which their service life expires;
e.g. DO NOT USE AFTER 2021. High pressure pipes are marked with their maximum working
pressure e.g. MAX 400 MPa.
All flexible pressure hoses are subject to ageing and, after a number of years, the performance
deteriorates. All SKF flexible pressure hoses are hard marked with the year in which their life
expires, e.g. LIFE EXPIRES 2021.
68
Maximum working pressure up to 150 MPa (21 750 psi)
SKF Flexible High-pressure Hoses
The SKF flexible pressure hoses are designed to be used together with
the quick connect coupling SKF 729831 A and nipple SKF 729832 A on
the range of SKF Hydraulic Pumps.
Technical data
Designation Bore Outside Maximum Minimum Minimum End Working Length Weight
diameter diameter working burst bending fittings temperature
pressure pressure radius
mm in. mm in. MPa psi MPa psi mm in. C F mm in. kg lb
729126 4,0 0.16 10 0.39 100 14 500 300 43 500 65 2.6 G 1 /4 30/80 22/176 1 500 59 0,4 0.9
729834 5,0 0.20 11 0.43 150 21 750 450 65 250 150 5.9 G 1 /4 30/80 22/176 3 000 118 0,9 2.0
1 500 3 000
Technical data
Designation Blade length Blade thickness
mm in. mm in. mm in. mm in.
729865 A 100 4.0 0,03 0.0012 0,08 0.0031 0,14 0.0055
0,04 0.0016 0,09 0.0035 0,15 0.0059
0,05 0.0020 0,10 0.0039 0,20 0.0079
0,06 0.0024 0,12 0.0047 0,30 0.0118
0,07 0.0028
729865 B 200 8.0 0,05 0.0020 0,18 0.0071 0,60 0.0236
0,09 0.0035 0,19 0.0075 0,65 0.0256
0,10 0.0039 0,20 0.0079 0,70 0.0276
0,11 0.0043 0,25 0.0098 0,75 0.0295
0,12 0.0047 0,30 0.0118 0,80 0.0315
0,13 0.0051 0,35 0.0138 0,85 0.0335
0,14 0.0055 0,40 0.0157 0,90 0.0354
0,15 0.0059 0,45 0.0177 0,95 0.0374
0,16 0.0063 0,50 0.0197 1,00 0.0394
0,17 0.0067 0,55 0.0216
69
For easy pressure hose connection
SKF Quick Connecting Coupling and Nipples
One coupling and two different nipples are available to connect SKF Hydraulic
Pumps to the work piece. When nipples with other thread types are required,
select an additional SKF nipple from the range to make the connection.
SKF Nipple 729832 A is supplied standard with all SKF Hydraulic Nuts
HMV ..E series.
Technical data
Designation Thread Dimensions Maximum pressure
Coupling d2 D2 C A
729831 A G 1/4 24 mm (0.94 in.) 27 mm (1.06 in.) 58 mm (2.28 in.) 150 MPa (21 750 psi)
d2 D2 C
A
Nipples d1 D1 B A
729832 A G 1/4 22 mm (0.87 in.) 14 mm (0.55 in.) 46 mm (1.81 in.) 150 MPa (21 750 psi) B
729100 G 1/8 17 mm (0.67 in.) 14 mm (0.55 in.) 43mm (1.69 in.) 100 MPa (14 500 psi)
D1 d1
Technical data
Designation Thread Length
233950 E G 1/4 15 mm (0.59 in.)
729944 E G 1/2 17 mm (0.67 in.) G1/4 8 11
G1/2 4 G3/4 15
1030816 E G 3/4 23 mm (0.90 in.)
4,5 4
6 45 14
9
15 16 22
Maximum working pressure 400 MPa (58 000 psi) Plug 233950 E Plug 729944 E Plug 1030816 E
70
SKF Connection Nipples
SKF provides a wide range of connection nipples covering many different thread
combinations and sizes. They are used as adapters to enable pipes and hoses to
be connected to different thread sizes.
A G2 A1 A
1) Not suitable for use with quick connection couplings and nipples !
71
Catering for adapter and withdrawal sleeve applications
SKF Extension Pipes
Technical data
Designation Max. Designation Max. Designation Max. Designation Max.
pressure pressure pressure pressure
pipe 50 MPa pipe 100 MPa pipe 100 MPa 227965/100MPA 100 MPa
234064 (7 250 psi) 1077453/100MPA (14 500 psi) 227966/100MPA (14 500 psi) (14 500 psi)
nipple 50 MPa nipple 100 MPa
234063 (7 250 psi) 1077454/100MPA (14 500 psi)
7 2 12 2,5 17 4 15 3
60 300 15 15
42 34
15 15 15 15
M4 extension pipe with M6 extension pipe with G 1/4 extension pipe G 1/8 extension pipe
connection nipple connection nipple
72
SKF Adapter Block 226402
The adapter block SKF 226402 consists of a cast steel block to which a
pressure gauge and high-pressure pipe can be connected. It comes with
a floor support and a 90 degree connection nipple for the oil reservoir.
Technical data
Designation 226402
Maximum pressure 400 MPa
(58 000 psi)
Pressure gauge connection G 1/2
Pressure pipe connection G 3/4 245
610
Technical data
Designation LHDF 900/pack size LHMF 300/pack size
Specific gravity 0,885 0,882
Flash point 202 C (395 F) 200 C (390 F)
Pour point 28 C (18 F) 30 C (22 F)
Viscosity at 20 C (68 F) 910 mm2/s 307 mm2/s
Viscosity at 40 C (104 F) 330 mm2/s 116 mm2/s
Viscosity at 100 C (212 F) 43 mm2/s 17,5 mm2/s
Viscosity index 187 167
Available pack size 5 and 205 litre 1, 5, 205 litre
73
Also available from SKF
Mounting bearings made easy
SKF Adapter and withdrawal sleeves for oil injection
These SKF sleeves facilitate the use of the SKF Oil Injection Method.
The larger sleeves have oil supply ducts and distribution grooves,
enabling the user to inject oil between the sleeve and bearing bore and
between the sleeve and the shaft. This oil reduces friction and force
necessary for mounting, particularly when mounting in a dry state.
Reduces the risk of damage to shaft and sleeve
Reduces time to mount and dismount bearings
A full range of pumps, nipples and pipes are available
SKF sleeves also help make bearing dismounting easier
For more information, please refer to the SKF General Catalogue, the
SKF Maintenance Handbook or consult an SKF application engineer.
The TMEM 1500 is only compatible with SKF bearings, which are fitted
with the SensorMount sensor. These bearings from SKF have the
designation suffixes ZE, ZEB, or ZEV, e.g. ZE 241/500 ECAK30/W33.
The SensorMount Indicator provides a numeric value, which guides the
user in achieving a reliable bearing fit. SKF bearings fitted with the
SensorMount system can also be mounted on adapter sleeves,
withdrawal sleeves and hollow shafts. The material composition of the
shaft has no effect on the proper operation of the SensorMount system.
74
OK Coupling mounting and dismounting kits
Technical data
Coupling size Designation Contents Weight Application
OKC 45OKC 90 TMHK 35 1 226400 E Injector with spares 12 kg
1 226402 Adapter block (26.5 lb)
1 228027 E Nipple
1 729944 E Plug
1 227958A Pressure pipe (for OKC 80 and 90)
1 728017A/2000 Pressure pipe (for OKC 4575)
Tools and storage case
OKC OKF
OKC 180OKC 490 TMHK 38S 1 THAP 030E/SK1 Air-driven pump set 81,7 kg
OKF 300OKF 700 1 729147A Return hose (180 lb)
Shipyard or frequent use 1 THAP 300E Air-driven oil injector
1 226400 E Injector with spares
OKC OKF
OKC 500 and larger TMHK 41 1 THAP 030E/SK1 Air-driven pump 136 kg
Shipyard or frequent use 3 THAP 300E Air-driven oil injector (300 lb)
1 729147A Return hose
75
Accurate shaft
alignment reduces
machinery breakdowns
and increases your
uptime.
Julien Meunier,
Business Development &
Product Development Manager
76
Instruments
Alignment 78
Basic condition monitoring 98 Dismounting Buy a bearing
Basic
condition Mounting
monitoring
Alignment Lubrication
77
Alignment
Correct
alignment
78
TKSA 51 TKSA 71
TKSA 80
Accuracy -- ++ ++
Speed ++ -- +
Ease of use ++ -- +
79
New technology makes shaft alignment easier and more affordable
SKF Shaft Alignment Tool TKSA 11
The SKF TKSA 11 is an innovative shaft alignment tool that uses smartphones and tablets
and intuitively guides the user through the shaft alignment process. With a focus on the core
alignment tasks, the TKSA 11 is designed to be a very easy-to-use instrument that is especially
suitable for alignment learners and compact applications. The SKF TKSA 11 is the first
instrument on the market that uses inductive proximity sensors, enabling accurate and
reliable shaft alignment to be affordable for every budget.
Live view of the instrument and motor By using inductive proximity sensors,
position makes the measurement and the measurement is no longer affected by
horizontal alignment intuitive and easy. bright sunlight, the influence of backlash is
The TKSA 11 app offers a fully functional reduced and the instrument becomes more
demonstration mode allowing the complete robust. All enabling the TKSA 11 to deliver
alignment process to be experienced without accurate and reliable shaft alignments.
the need to purchase the TKSA 11. Automatic alignment reports give a complete
The TKSA 11 is designed to give a fast return overview of the alignment process and
on its investment and is also affordable for results. Reports can easily be shared via
almost every budget. email or cloud services.
Also available as TKSA 11D with rugged,
industrial display device and pre-installed
apps included.
80
The intuitive and affordable laser shaft alignment system
SKF Shaft Alignment Tool TKSA 31
The TKSA 31 is SKFs most affordable solution for easy laser shaft alignment. The ergonomic
display unit with touch screen makes the instrument very easy to use and the built-in machine
library helps storing alignment reports for multiple machines. Large sized laser detectors in the
measuring heads reduce the need for pre-alignments and the embedded soft foot tool helps
establish the foundation for a successful alignment. Additional functions such as live view and
automatic measurement support fast and effective alignment tasks and make the TKSA 31 an
innovative laser shaft alignment tool that is affordable for almost every budget.
Easy measurements can be performed Automatic reports are generated after each
by using the well-known three position alignment and can be customised with notes
measurement (9-12-3 oclock) with about the application. All reports can be
additional positioning flexibility of 40 exported as pdf files.
around each measurement position. The machine library gives an overview of
High affordability is achieved by focussing all machines and alignment reports.
on the standard shaft alignment process It simplifies the machine identification
and essential functions to allow quick and and improves the alignment workflow.
effective shaft alignments.
"Automatic measurement enables hands-
free measurements by detecting the position
of the heads and only taking a measurement
when the heads are in the right position.
81
The advanced laser shaft alignment system with enhanced measuring and reporting capabilities
SKF Shaft Alignment Tool TKSA 41
The ergonomic display unit with intuitive touch Automatic reports are generated after each
screen navigation makes your alignments fast alignment. The reports can be customised
and easy, whilst innovative features, like the with notes and pictures from the built-in
free measurement, increase the alignment camera for the most comprehensive
Free measurement allows alignment performance. With the focus on improving overview. All reports can be exported as
measurements to start at any angle and alignment practices, the SKF Shaft Alignment pdf files.
finish with an angular sweep of just 90. Tool, TKSA 41, is one of the industrys best Live view supports intuitive measurements
value alignment solutions. and facilitates horizontal and vertical
alignments.
Wireless communication improves The simplicity of the TKSA 41 provides
instrument handling and allows alignments greater confidence for the performance of
of difficult to reach applications from a safe alignment tasks on all types of horizontal
position. rotating machines.
Automatic measurement enables hands- QR codes can be used to further simplify
free measurements by detecting the head machine identification and improve the
position and taking a measurement when alignment workflow.
the heads are rotated into the right position.
82
Comprehensive and intuitive shaft alignment utilising tablets and smart phones
SKF Shaft Alignment Tool TKSA 51
The TKSA 51 shaft alignment tool provides high measurement flexibility Alignment applications
and performance suitable for entry-level to expert alignment jobs. Designed The TKSA 51 uses dedicated apps for
alignments of horizontal and vertical
to work with the SKF shaft alignment apps on a tablet or smart phone, this
shaft and the correction of soft foot.
intuitive tool is easy to use and requires no special training.
The apps are icon-driven and very easy
to use. All apps are free of charge and
features a fully functional demonstration
The included accessories enable use of the Comprehensive and compact - A range of mode that allows the alignment process
TKSA 51 for a wide range of alignment included components, such as magnetic to be experienced before purchasing the
applications with horizontal and vertical shafts, mounting brackets and extension rods and instrument.
such as motors, drives, fans, pumps, gearboxes chains, increase the TKSA 51's versatility,
and more. The apps include tutorial videos to yet it remains compact, lightweight and easy
show operators how to perform accurate to carry.
measurements. 3-D live view - This feature enables intuitive Shaft alignment
positioning of the heads for quick alignment
Measurement flexibility - The well-known, measurements and displays the horizontal
three-position measurement gains and vertical alignment correction live. The
additional flexibility as measurements can apps enable 3-D rotation of the virtual
start at any angle and require a total motor to correspond with the actual
minimal rotation of only 40 degrees. This machine position view. Vertical shaft
enables operators to perform alignments of Disturbance compensation - Measurement alignment
applications with limited space. values are averaged over time to provide
Automatic reports - Alignment reports are greater accuracy in presence of external
generated automatically and can be disturbances.
customised with notes, a machine picture Also available as TKSA 51D with rugged,
and a signature via touchscreen. The reports industrial display device and pre-installed Soft foot
can be easily exported as PDF files and apps included
shared with other mobile apps.
83
Versatility and performance for professional alignment
SKF Shaft Alignment Tool TKSA 71
Superior alignment performance and long-term industrial durability Superior alignment performance - Up to 10 m measurement
are achieved with an innovative instrument design that offers high distance, disturbance compensation, measurement flexibility, only 40
measurement accuracy and excellent protection against dust and water total rotation, automatic measurement and customised alignments
in harsh environments. with target values
Protection against harsh environments - Completely sealed
Easy-to-use - Intuitive software applications, guided alignment measuring units (IP67) to withstand dust and water
processes and explanatory videos Ultra-compact measuring units - Use in extremely narrow spaces
Wide range of applications - Comprehensive accessories and Robust carrying case - Excellent protection, convenient transport and
dedicated software applications wireless in-case charging
10 7
Measuring device: (1) Measuring units (M & S) with standard V-bracket, (2) Wireless charging pods with USB cable, (3) Tape measure
Standard accessories: (4) Extension chains, (5) Extension rods, (6) Mounting magnets
Advanced accessories: (7) Sliding brackets, (8) Offset brackets, (9) Additional extension rods, (10) Magnetic bases
84
Alignment applications
The TKSA 71 functions quickly and intuitively using six software apps tailored for different
alignment jobs. Designed for use without prior training, these simple-to-use apps are available
free of charge for both Android and iOS platforms. Common features include comprehensive,
automatic reports, export and sharing options, machine library with QR code identification,
instructional videos within the app, built-in tolerance guidelines, 3-D live view, disturbance
compensation and a fully functional demonstration mode.
1) Compatible with: TKSA 51, TKSA 51D, TKSA 71, TKSA 71/PRO, TKSA 71D, TKSA 71D/PRO. 2) Compatible with: TKSA 71, TKSA 71/PRO, TKSA 71D, TKSA 71D/PRO.
85
Selection chart
TKSA11 TKSA 31 TKSA41 TKSA51 TKSA71 TKSA71/PRO
User interface phone, tablet touch screen touch screen phone, tablet phone, tablet phone, tablet
Type of display device (iOS & Android) display device display device (iOS & Android) (iOS & Android) (iOS & Android)
TKSA 71/PRO:
Display device included
TKSA 11: no 1) TKSA 51: no 1) TKSA 71: no 1) no 1)
yes yes
TKSA 11D: yes TKSA 51D: yes TKSA 71D: yes TKSA 71D/PRO:
yes
Measurement positions
The 9-12-3 measurement directs the user to three pre-defined
measurement positions. The free measurement allows the user to 9-12-3 9-12-3 free free free free
freely select the measurement positions. All measurements are
guided.
Camera
Machine picture(s) can be taken and added to alignment reports. -
Machine library
Overview of all registered machines and previous alignment -
reports.
QR code recognition
QR labels can be used to simplify the machine identification and - -
increase the usage convenience.
Machine view
The machine view describes how the machine is shown on the free 3D free 3D free 3D
fixed 2D view fixed 3D view fixed 3D view
display. The free 3D rotation allows to view the machine from all rotation rotation rotation
directions.
Target values
Using target values for alignment, it is possible to compensate for - - -
thermal expansion or similar adjustments.
Disturbance compensation
Measurement values are averaged over time, allowing accurate
measurements in the presence of laser distortions from air - - -
temperature gradients or similar disturbances.
1) Requires offset brackets TKSA EXT50 or TKSA EXT100 for usage with TKSA 31 and TKSA 41.
87
Technical data
Designation TKSA 11 TKSA 31 TKSA 41
Sensors and communication 2 Inductive proximity sensors 29 mm (1.1 in.) CCD with red line laser Class 2 29 mm (1.1 in.) CCD with line laser Class 2
Inclinometer 0.5, Bluetooth 4.0 LE Inclinometer 0.5, Wired, USB cables Inclinometer 0.5; Bluetooth 4.0 LE and
wired, USB cables
System measuring distance 0 to 185 mm (0 to 7.3 in.) between brackets 0,07 to 4 m (0.23 to 13.1 ft) 0,07 to 4 m (0.23 to 13.1 ft)
3 reference bars included up to 200 mm (up to 2 m (6.6 ft) with cables supplied)
(7.9 in.)
Measuring errors <2% <0,5% 5 m < 0,5% 5 m
Housing material PC/ABS plastic 20% Glass filled Polycarbonate 20% Glass filled Polycarbonate
Operating time Up to 18 hours, N/A Up to 16 hours
rechargeable LiPo battery Rechargeable LiPo battery
Dimensions 105 55 55 mm (4.1 2.2 2.2 in.) 120 90 36 mm (4.7 3.5 1.4 in.) 120 90 36 mm (4.7 3.5 1.4 in.)
Weight 155 g (0.34 lb) 180 g (0.4 lb) 220 g (0.5 lb)
Operating device TKSA DISPLAY, Galaxy Tab Active and iPad Mini 5.6" colour resistive touchscreen LCD display. 5.6" colour resistive touchscreen LCD display.
recommended, iPad 3rd generation, iPod Touch High Impact PC/ABS with overmould High Impact PC/ABS with overmould
5th generation, iPhone 4S, Galaxy S4 or above
(all not included)
Software/App update Apple AppStore or on Google Play Store via USB stick via USB stick
Operating system requirements Apple iOS 9 or Android OS 4.4.2 (and above) N/A N/A
DU Operating time N/A Up to 7 hours (100% backlight) Up to 8 hours (100% backlight)
Dimensions N/A 205 140 60 mm (8.1 5.5 2.4 in.) 205 140 60 mm (8.1 5.5 2.4 in.)
Weight N/A 420 g (0.9 lb) 640 g (1.4 lb)
Alignment method Alignment of horizontal shafts Alignment of horizontal shafts, Alignment of horizontal shafts,
3 position measurement 9123 3 position measurement 9 -12 -3 3 position measurement 9 -12 -3,
(with min. 140 rotation), automatic measurement,
automatic measurement, soft foot measurement (with min. 90 rotation),
soft foot
Live correction values Only for horizontal Vertical and horizontal Vertical and horizontal
Extra features Automatic .pdf report Machine library, screen orientation flip, Machine library, QR code reading,
automatic .pdf report screen orientation flip, automatic .pdf report
Fixture 2 V-brackets with chains, 2 V-brackets with chains, 2 V-brackets with chains,
width 15 mm (0.6 in.) width 21 mm (0.8 in.) width 21 mm (0.8 in.)
Shaft diameters 20 to 160 mm (0.8 to 6.3 in.) 20 to 150 mm (0.8 to 5.9 in.) 20 to 150 mm (0.8 to 5.9 in.)
300 mm (11.8 in.) with optional extension 300 mm (11.8 in.) with optional extension
chains (not included) chains (not included)
Max. coupling height 1) 55 mm (2.2 in.) with standard 80 mm rods 105 mm (4.2 in.) with standard rods 105 mm (4.2 in.) with standard rods
(Unit should be mounted on the coupling 195 mm (7.7 in.) with optional extension rods 195 mm (7.7 in.) with extension rods
when possible) (not included) (included)
Power adapter Charging via micro USB port (5V) Input: 100V-240V 50/60Hz AC power supplier Input: 100V-240V 50/60Hz AC power supplier
Micro USB to USB charging cable supplied Output: DC 12V 3A Output: DC 12V 3A
Compatible with 5V USB chargers (not with EU, US, UK, AUS adapters with EU, US, UK, AUS adapters
included)
Operating temperature 0 to 45 C (32 to 113 F) 0 to 45 C (32 to 113 F) 0 to 45 C (32 to 113 F)
IP rating IP 54 IP 54 IP 54
Carrying case dimensions 355 250 110 mm (14 9.8 4.3 in.) 530 110 360 mm (20.9 4.3 14.2 in.) 530 110 360 mm (20.9 4.3 14.2 in.)
Total weight (incl. case) 2,1 kg (4.6 lb) 4,75 kg (10.5 lb) 4.75 kg (10.5 lb)
Calibration certificate Supplied with 2 years validity Supplied with 2 years validity Supplied with 2 years validity
Case content Measuring unit; 3 reference bars; 2 shaft 2 measuring units (M&S); display unit; 2 measuring units (M&S); display unit; 2 shaft
brackets with chains 480 mm (18.9 in.) and 2 shaft brackets with chains 400 mm (15.8 in.) brackets with chains 400 mm (15.8 in.) and
rods 80 mm (3.1 in.); micro USB to USB and threaded rods 150 mm (5.9 in.); chain threaded rods 150 mm (5.9 in.); chain tightening
charging cable; measuring tape 2 m (6.6 ft.); tightening rod; power supply with country rod; 4 threaded extension rods 90 mm (3.5 in.);
printed certificate of calibration and adapters; 2 micro USB to USB cables; power supply with country adapters; 2 micro USB
conformance; printed quick start guide (EN); measuring tape; printed certificate of to USB cables; measuring tape; printed certificate
SKF carrying case calibration and conformance; printed quick of calibration and conformance; printed quick start
start guide (EN); SKF carrying case guide (EN); SKF carrying case; A4 sheet with
12 QR code stickers
1) Depending on the coupling, the brackets can be mounted on the coupling, reducing the coupling heigt limitation.
88
TKSA 51 TKSA 71, TKSA 71/PRO
20 mm (0.8 in.) PSD with line laser Class 2 20 mm (0.8 in) 2nd gen. PSD with line laser Class 2
Inclinometer 0.1; Bluetooth 4.0 LE inclinometer 0.1; Bluetooth 4.0 LE
<1% 10 m <1% 10 m
Anodized Aluminum front and PC/ABS plastic back cover Anodized aluminum front and PC/ABS plastic back cover
Up to 8 hours, rechargeable Li-ion battery Up to 8 hours, rechargeable Li-ion battery, wireless fast charging
fast charging: 10 min. charging for 1h usage 10 min. charging for 1h usage
52 64 50 mm (2.1 2.5 2 in.) 52 64 33 mm (2.1 2.5 1.3 in.)
190 g (0.4 lb) 130 g (0.3 lbs)
TKSA DISPLAY, Galaxy Tab Active and iPad Mini recommended TKSA DISPLAY, Galaxy Tab Active and iPad Mini recommended
iPad 3rd generation, iPod Touch 5th generation iPad 3rd generation, iPod Touch 5th generation
iPhone 4S, Galaxy S4 or above (all not included) iPhone 4S, Galaxy S4 or above (all not included)
Apple AppStore or on Google Play Store Apple AppStore or on Google Play store
Apple iOS 9 or Android OS 4.4.2 (and above) Apple iOS 9 or Android OS 4.4.2 (and above)
N/A N/A
N/A N/A
N/A N/A
Alignment of horizontal and vertical shafts, Alignment of horizontal and vertical shafts,
3 position measurement 9 -12 -3, automatic measurement, 3 position measurement 9 -12 -3, automatic measurement,
measurement (with min. 40 rotation), soft foot measurement (with min. 40 rotation), soft foot,
machine trains, values, spacer shafts
45 mm (1.8 in.) with standard rods 45 mm (1.8 in.) with standard rods
plus 120 mm (4.7 in.) per set of extension rods plus 120 mm (4.7 in.) per set of extension rods
Charging via micro USB port (5V) Wireless charging via supplied charging pods
Micro USB to USB split charging cable supplied micro USB to USB split charging cable supplied
Compatible with 5V USB chargers (not included)
89
For accurate vertical machinery alignment A 2 inch B 2 inch C 0.51 inch
Pack designation Thickness (inch)
SKF Machinery Shims TMAS series TMAS 2-002 0.002
TMAS 2-005 0.005
TMAS 2-010 0.010
Accurate machine adjustment is an essential element of any TMAS 2-020 0.020
alignment process. TMAS 2-025 0.025
TMAS 2-050 0.050
TMAS 2-075 0.075
TMAS 2-100 0.100
Made of high quality stainless steel, allowing re-use TMAS 2-125 0.125
Easy to fit and to remove
Close tolerances for accurate alignment
Thickness clearly marked on each shim A 3 inch B 3 inch C 0.83 inch
Fully de-burred Pack designation Thickness (inch)
Pre-cut shims are supplied in packs of 10 and complete kits are also available TMAS 3-002 0.002
Shim packs and kits are available with thicknesses in millimeter and inch TMAS 3-005 0.005
TMAS 3-010 0.010
TMAS 3-020 0.020
TMAS 3-025 0.025
TMAS 3-050 0.050
TMAS 3-075 0.075
TMAS 3-100 0.100
TMAS 3-125 0.125
TMAS 510IN 1) 22 20 20 20 20 20 20 20 20 10
33 20 20 20 20 20 20 20 20 10
44 20 20 20 20 20 20 20 20 10
TMAS 680IN 2) 22 20 20 20 20 20 20 20 20 10 B C
33 20 20 20 20 20 20 20 20 10
44 20 20 20 20 20 20 20 20 10
A
55 20 20 20 20 20 20 20 20 10
90
Metric Thickness (mm)
0,05 0,10 0,20 0,25 0,40 0,50 0,70 1,00 2,00
Designation Size (mm) Quantities
TMAS 50/KIT 50 50 20 20 20 20 20 20 20 20 10
TMAS 75/KIT 75 75 20 20 20 20 20 20 20 20 10
TMAS 360 50 50 20 20 20 20 20 20
75 75 20 20 20 20 20 20
100 100 20 20 20 20 20 20
TMAS 380 50 50 20 20 20 20 20 20 20 20 20
75 75 20 20 20 20 20 20 20 20 20
TMAS 510 50 50 20 20 20 20 20 20 20 20 10
75 75 20 20 20 20 20 20 20 20 10
100 100 20 20 20 20 20 20 20 20 10
TMAS 720 1) 50 50 20 20 20 20 20 20 20 20 20
75 75 20 20 20 20 20 20 20 20 20
100 100 20 20 20 20 20 20 20 20 10
125 125 20 20 20 20 20 20 20 20 10 1) Consists of TMAS 340 + TMAS 380
A 50 mm B 50 mm C 13 mm A 75 mm B 75 mm C 21 mm A 100 mm B 100 mm C 32 mm
Pack designation Thickness (mm) Pack designation Thickness (mm) Pack designation Thickness (mm)
TMAS 50-005 0,05 TMAS 75-005 0,05 TMAS 100-005 0,05
TMAS 50-010 0,10 TMAS 75-010 0,10 TMAS 100-010 0,10
TMAS 50-020 0,20 TMAS 75-020 0,20 TMAS 100-020 0,20
TMAS 50-025 0,25 TMAS 75-025 0,25 TMAS 100-025 0,25
TMAS 50-040 0,40 TMAS 75-040 0,40 TMAS 100-040 0,40
TMAS 50-050 0,50 TMAS 75-050 0,50 TMAS 100-050 0,50
TMAS 50-070 0,70 TMAS 75-070 0,70 TMAS 100-070 0,70
TMAS 50-100 1,00 TMAS 75-100 1,00 TMAS 100-100 1,00
TMAS 50-200 2,00 TMAS 75-200 2,00 TMAS 100-200 2,00
TMAS 50-300 3,00 TMAS 75-300 3,00 TMAS 100-300 3,00
91
Shims with customized shape for special applications
Custom shims
SKF Machinery Shims can be custom cut to better suit the adjustment needs of
your application. Typical applications for custom-cut shims include large machines
that require shims longer or wider than 200 mm or machine feet that require
elongated shims to support the machines weight.
In addition to the typical shape of pre-cut shims, fully customized Custom shims to meet the needs of large or specialized applications
shapes, such as double-slot shims or washer-like shims, are available. Shim shape can be chosen freely
For more information about custom-cut shims, please contact your Made of high-quality stainless steel, enabling re-use
local SKF Authorised Distributor or SKF sales representative. Available in standard metric and imperial thicknesses,
Custom-cut shims are supplied in packs of 10 and require a well-
defined drawing or sketch
Note: Should you be unable to find a suitable product, please contact your local SKF Authorised Distributor or SKF sales representative.
92
The universal adjustable re-useable chock
SKF Vibracon
SKF Vibracon is a machinery mounting chock that is easily and accurately
adjusted. The chock accommodates the angular difference, up to 4, between
machine and the mounting base without expensive machining of the base or
the extra work of installing epoxy resin chocks. The self-levelling capability,
combined with the height adjustment feature, eliminates the possibility of a
soft foot in the production line throughout the life cycle of the machinery.
Dimensions (mm)
Designation A min A max d1 d2
SM 12 -CS SM 12 -CSTR SM 12 -SS 30 38 60 17
SM 16 -CS SM 16 -CSTR SM 16 -SS 35 45 80 21
SM 20 -CS SM 20 -CSTR SM 20 -SS 40 50 100 25
SM 24 -CS SM 24 -CSTR SM 24 -SS 45 57 120 31
SM 30 -CS SM 30 -CSTR SM 30 -SS 50 62 140 37
SM 36 -CS SM 36 -CSTR SM 36 -SS 55 67 160 44 The SKF Vibracon app provides a
SM 42 -CS SM 42 -CSTR SM 42 -SS 60 72 190 50 calculation tool to determine the most
SM 48 -CS SM 48 -CSTR SM 48 -SS 70 85 220 60 suitable SKF Vibracon chock for your
SM 56 -CS SM 56 -CSTR SM 56 -SS 75 90 230 66 application and includes additional
SM 64 -CS SM 64 -CSTR SM 64 -SS 80 95 250 74 information and contact details for a more
specific engineering proposal. Simply
follow the QR code to quickly find the app
Designation A min A max d1 d2 for Android and iOS devices.
4
SM 16 LP-ASTR 20 30 80 21
SM 20 LP-ASTR 20 30 100 25 Please contact your local SKF Authorised
A
SM 24 LP-ASTR 20 30 120 31 Distributor or SKF sales representative for
SM 30 LP-ASTR 20 30 140 37 support, customization or more
d2 SM 36 LP-ASTR 20 40 160 44 information about SKF Vibracon.
d1
SM 42 LP-ASTR 35 45 190 50
93
Straight bolt tensioning for longer endurance
SKF Spherical Washers
Spherical washers are designed to create an exact, parallel plane between the
bolt head and the face of the nut. SKF spherical washers automatically adjust
and compensate for the angular deviation between the planes and prevent the
bolt from bending.
Product characteristics:
Automatically compensates for angular errors
Evenly distributed bolt tension
Reduces bolt fatigue from bending bolts
Improved bolt stretch possible due to increased clamping length
Bent bolt Surface treated for protection in humid and harsh environments
Available in standard and low-profile (LP) versions
Straight bolt
low-profile (mm)
Designation D d H
SMSW 16LPAST 33 17 20
Spherical contact SMSW 20LPAST 42 23 22 D
SMSW 24LPAST 47 27 24 d
SMSW 27LPAST 52 30 26
SMSW 30LPAST 56 34 28
H
SMSW 36LPAST 67 40 30
SMSW 42LPAST 82 46 34
Please contact your local SKF Authorised Distributor or SKF sales representative for support, customization or more information about
94 spherical washers from SKF.
SKF Belt Alignment Tools
One of the common reasons for unplanned downtime of belt-driven machinery is
pulley misalignment. Pulley misalignment can increase wear on pulleys and belts as
well as increasing the noise and vibration level, that can result in unplanned
machinery downtime. Another side effect of increased vibration is premature
bearing failure. This too can cause unplanned machinery downtime.
Parallel misalignment
Correct alignment
95
Beltdriven machinery downtime caused by misalignment is a thing of the past
SKF TKBA Series
SKF offers a range of three different belt alignment tools to enable accurate alignment for almost
all applications. The tools are designed to be easy to use without any special training. The laser
position indicates the nature of misalignment allowing easy and accurate adjustment.
The SKF TKBA 10 and TKBA 20 allow pulleys and sprockets to be The SKF TKBA 40 aligns V-belt pulleys in the grooves. Vguides and
aligned on the side face. The unit magnetically attaches to the inside powerful magnets allow the TKBA 40 to be fitted in the grooves of the
or outside face of almost any belt pulley or chain sprocket and has no pulley. With only two components, a laseremitting unit and a receiver
small parts or targets that can get lost. A laser line is projected from the unit, the belt alignment tool is easy and fast to attach. The three
transmitter unit to the reflector unit mounted on the opposite pulley. dimensional target area on the receiver unit allows the easy detection
A reference line on the reflector unit directly indicates the offset and of misalignment as well as its nature; whether it is horizontal, vertical,
vertical angle misalignment. The reflected laser line shown on the parallel or a combination of all three.
transmitter unit shows the horizontal angle misalignment of all three.
Powerful magnets allow fast and easy attachment
Powerful magnets allow fast and easy attachment Three-dimensional target area simplifies the alignment process
Facilitates simultaneous adjustment of tension and alignment Facilitates simultaneous adjustment of tension and alignment
Can be used on almost all machines using V belts, banded belts, V-guides facilitate the alignment of a wide range of V-belt pulleys
ribbed belts and most other belts as well as chain sprockets Aligns grooves of a V-belt pulley rather than its face, allowing optimum
SKF TKBA 10 utilises a red laser and can be used for distances alignment of pulleys of unequal width or with dissimilar faces
up to 3 m (10 ft) A maximum operating distance of 6 m (20 ft) accommodates many
SKF TKBA 20 utilises a highly visible green laser and can be used applications
for distances up to 6 m (20 ft). It can even be used outdoors Special side adaptor allowing alignment of multi-ribbed and timing
in sunny conditions belt pulleys as well as sprockets is available as accessory
Sturdy aluminium housings help ensure assembly stability and
accuracy during the alignment process
96
SKF TKBA 20 utilises a highly SKF Belt Frequency Meter
visible green laser and can be PHL FM10/400
used for distances up to 6 m (20 ft).
It can even be used outdoors in
sunny conditions
TKBA 10 TKBA 20
Technical data
Designation TKBA 10 TKBA 20 TKBA 40
Type of laser Red laser diode Green laser diode Red laser diode
Laser 1 Built-in class 2 laser, <1 mW, 635 nm 1 Built-in class 2 laser, <1 mW, 532 nm 1 Built-in class 2 laser, <1 mW, 632 nm
Laser line length 2 m at 2 m (6.6 ft at 6.6 ft) 2 m at 2 m (6.6 ft at 6.6 ft) 3 m at 2 m (9.8 ft at 6.6 ft)
Measurement accuracy angular Better than 0,02 at 2 m (6.6 ft) Better than 0,02 at 2 m (6.6 ft) Better than 0,2
Measurement accuracy offset Better than 0,5 mm (0.02 in.) Better than 0,5 mm (0.02 in.) Better than 0,5 mm (0.02 in.)
Measurement distance 50 mm to 3 000 mm (2 in. to 10 ft) 50 mm to 6 000 mm (2 in. to 20 ft) 50 mm to 6 000 mm (2 in. to 20 ft)
Control Laser on/off rocker switch Laser on/off rocker switch Laser on/off switch
Housing material Aluminum, powder coat finish Aluminum, powder coat finish Extruded aluminium
Dimensions
Transmitter unit 169 51 37 mm (6.65 2.0 1.5 in.) 169 51 37 mm (6.65 2.0 1.5 in.) 70 74 61 mm (2.8 2.9 2.4 in.)
Receiver unit 169 51 37 mm (6.5 2.0 1.5 in.) 169 51 37 mm (6.5 2.0 1.5 in.) 96 74 61 mm (3.8 2.9 2.4 in.)
Reflector dimensions 22 32 mm (0.9 1.3 in.) 22 32 mm (0.9 1.3 in.) N/A
Weight
Transmitter unit 365 g (0.8 lb) 365 g (0.8 lb) 320 g (0.7 lb)
Receiver unit 340 g (0.7 lb) 340 g (0.7 lb) 270 g (0.6 lb)
Mounting Magnetic, side mounted Magnetic, side mounted Magnetic, groove mounted
(optional side adapter TMEB A2)
V-guides N/A N/A Size 1: 22 mm, short rods (3 pairs)
Size 2: 22 mm, long rods (3 pairs)
Size 3: 40 mm, short rods (3 pairs)
Size 4: 40 mm, long rods (3 pairs)
Battery 2 AAA Alkaline type IEC LR03 2 AAA Alkaline type IEC LR03 2 AAA Alkaline type IEC LR03
Operation time 25 hours continuous operation 8 hours continuous operation 20 hours continuous operation
Carrying case dimensions 260 85 180 mm (10.2 3.3 7.1 in.) 260 85 180 mm (10.2 3.3 7.1 in.) 260 85 180 mm (10.2 3.3 7.1 in.)
Total weight (incl. case) 1,3 kg (2.9 lb) 1,3 kg (2.9 lb) 1,2 kg (2.7 lb)
Operating temperature 0 to 40 C (32 to 104 F) 0 to 40 C (32 to 104 F) 0 to 40 C (32 to 104 F)
Storage temperature 20 to +60 C (4 to +140 F) 20 to +60 C (4 to +140 F) 20 to +65 C (4 to +150 F)
Relative humidity 10 to 90% RH non-condensing 10 to 90% RH non-condensing 10 to 90% RH non-condensing
IP rating IP 40 IP 40 IP 40
Calibration certificate Valid for two years Valid for two years Valid for two years
Case contents 1 TKBA 10 transmitter unit 1 TKBA 20 transmitter unit 1 TKBA 40 transmitter unit
1 TKBA 10 receiver unit 1 TKBA 20 receiver unit 1 TKBA 40 receiver unit
2 AAA batteries 2 AAA batteries 2 AA batteries
1 Printed instructions for use 1 Printed instructions for use 4 sizes of V-guides, 3 of each size
1 Calibration certificate 1 Calibration certificate 1 Printed instructions for use
1 Calibration certificate
97
Basic condition monitoring
Basic condition monitoring is essential for achieving maximum bearing service life
To help ensure long bearing service life, it is important to To help you achieve the maximum service life from
determine the condition of machinery and bearings while your bearings, SKF has developed a wide range of
in operation. Good predictive maintenance will help reduce instruments for analysing the critical environmental
machine downtime and decrease overall maintenance costs. conditions which have an impact on bearing and
machine performance.
Maintenance concepts
Preventive maintenance
Preventive maintenance implies that a machine, or parts of a
machine, are overhauled on a regular basis regardless of the
condition of the parts. While preferable to run to failure maintenance,
preventive maintenance is costly because of excessive downtime from
unnecessary overhauls and the cost of replacing good parts along with
worn parts.
Preventive maintenance is similar to the regular service of a car.
Often, unnecessary maintenance is performed.
98
SKF has developed a comprehensive range of basic condition Subsequently, minor defects can be corrected quickly, as the operator
monitoring tools suitable for Operator Driven Reliability (ODR) and can undertake simple adjustment and repair tasks. Maintenance
maintenance technicians. Under ODR, some maintenance practices are technicians also have need for basic condition monitoring tools.
owned, managed, and performed by operators. Often, the operators If, for example, abnormal vibrations are detected or if an operator
are the best persons equipped for basic inspection activities, as they reports an abnormal running condition, then the technician can often
know their part of the plant very well. They are often sensitive to minor use some basic condition monitoring tools to detect the root cause for
changes in sounds and vibrations that may not be apparent to someone further evaluation.
lacking their front-line experience.
SKF basic condition monitoring tools can be used to check a number of properties:
Temperature
Since the dawn of the industrial age, operators and technicians know
that abnormal temperatures often indicate that something is wrong
with the machine. Such instruments as thermometers and thermal
imagers can help find and then measure these hotspots, allowing further
analysis to be conducted.
Speed
Machines are usually designed to run at a given speed. If the speed
is too slow or too fast, then the overall process can be compromised.
Using a hand-held tachometer enables a quick and easy assessment
of the machines running speed.
Visual
Visual inspection of a machines condition can sometimes be difficult when
its running or when there is a need to inspect the machine internally.
A stroboscope can be used to visually freeze the motion of a machine to
allow such things as fan blades, couplings and belt drives to be inspected
while running. To inspect the internal parts of a machine often requires
disassembly. By using an endoscope, it is possible to access the area of
interest with minimal disassembly, saving time and money.
99
Sound
Abnormal sounds from machines often indicate that something is wrong.
A stethoscope can be used to help pinpoint the source of the sound and
can aid the technician in identifying the problem. Leaks in compressed air
systems are costly, not only in energy costs but also due to extra costs in
air compressor maintenance. Ultrasonic leak detectors can help detect
leaks efficiently, allowing the necessary repairs to be made. Excessive
noise can cause worker fatigue, increased accidents and loss of hearing.
A sound pressure meter can measure the sound level, allowing corrective
measures to be made.
Vibration
Abnormal vibrations are often the first indication of a potential machine
failure. These vibrations can be caused by such conditions as unbalance,
misalignment, looseness of parts, rolling element bearing and gear
damage. Vibration analysis instruments and systems, can help detect
many serious problems at an early stage, allowing remedial work to be
undertaken in a timely manner.
Lubricant condition
To maintain the optimum condition of rolling element bearings, it is
essential that the lubricant is in good condition. Checking the oil or
grease condition at regular intervals can reduce downtime and greatly
prolong the life of rolling element bearings.
100
SKF Thermometers
SKF Thermometers are suitable for a wide range of applications. The pocket sized SKF TMTP 200
is a user friendly instrument with a sturdy flexible probe tip enabling many surface
temperatures to be measured. The SKF TKDT 10 has a wide temperature measurement
range and has the option to accommodate up to two SKF temperature probes.
Technical data
Designation TMTP 200 TKDT 10
Display 3 digit LCD Large back-lit LCD
Displayed resolution 1 for the entire range 0,1 up to 1 000 , otherwise 1
Measurement modes Max Min, max, average, differential, dual temperature reading
Measurement units C, F C, F, K
Temperature using probe 40 to +200 C (40 to +392 F) 200 to +1 372 C (328 to +2 501 F)
Accuracy 1,5 C (2.7 F) (acc. DIN IEC 584 class 1) >100 C (>148 F): 0.5% of reading 1 C (1.8 F)
Probe compatibility N/A 2 Type-K connectors
Probe supplied Embedded K-type thermocouple (NiCr/NiAl) TMDT 2-30, suitable for use up to 900 C (1 650 F)
Battery 3 AAA Alkaline type IEC LR03 3 AAA Alkaline type IEC LR03
Operation time 4 000 hours typical use 18 hours typical use (backlight on)
Product dimensions 165 50 21 mm (6.5 2 0.8 in.) 160 63 30 mm (6.3 2.5 1.2 in.)
Carrying case dimensions 260 85 180 mm (10.3 3.4 7.0 in.) 530 85 180 mm (20.9 3.4 7.0 in.)
Product weight 95 g (0.2 lb) 200 g (0.4 lb)
101
SKF Infrared thermometers
Infrared thermometers are portable, lightweight instruments for safely measuring
temperature at a distance. They are extremely user-friendly; simply aim and pull the
trigger and the temperature is shown on the display. These robust instruments are
equipped with a back-lit display and laser sighting. They are fitted with a bright LED
illuminator to allow the application object to be seen even in poorly lit environments.
Maximum temperature always shown; Supplied with temperature probe TMDT 2-30 Dual laser sighting feature defines the
helps identify the real hotspots (max. 900 C (1 652 F)); suitable for many diameter of the area being measured; helps
Auto shut off feature; helps optimise direct contact applications the user to precisely pin-point the
battery life Can be used with any SKF temperature temperature measurement area
Colour display with temperature trend probe Supplied with temperature probe TMDT 2-30
indication User selectable, multiple temperature (max. 900 C (1 652 F)); suitable for many
measurement modes including: maximum, direct contact applications
minimum, average, differential and probe/ Can be used with any SKF temperature
infrared dual display, scan function probe
User selectable high and low alarm levels User selectable, multiple temperature
with audible warning signal measurement modes including: maximum,
Mode dependant auto shut off feature minimum, average, differential and probe/
optimises battery life infrared dual display, scan function
Colour display with temperature trend User selectable high and level alarm levels
indication with audible warning signal
Mode dependant auto shut off feature
optimises battery life
102
When used in non-contact mode, the thermometer senses the
thermal energy radiated from an object with an infrared detector.
When pointed at an object, the infrared detector collects energy,
producing a signal that the microprocessor translates as a reading
on the backlit display. As the trigger is squeezed, the object
temperature is continuously measured by the infrared detector.
D:S = 50:1
This allows for fast and accurate realtime readings.
= 0,11,0
TKTL 40
Supplied with temperature probe TMDT 2-30 (max. 900 C (1 652 F))
An infrared and contact temperature thermometer with for direct contact applications. Can also be used with any other
video and data logging capabilities SKF temperature probe
User selectable, multiple temperature measurement modes including:
maximum, minimum, average, differential and probe/infrared
Built-in camera allows pictures and videos, with all measurement dual display
information to be taken, stored, recalled and exported to PC Data logging function can be used to visualise temperature changes
Environmental properties such as ambient, dew point and wet-bulb over time
temperatures, as well as relative humidity, can be displayed and stored User selectable high and low alarm levels with audible warning signal
Dual laser sighting defines the temperature measurement area User selectable auto shut off feature optimises the rechargeable
battery life
103
Technical data
Designation TKTL 10 TKTL 20 TKTL 30 TKTL 40
Probe supplied TMDT 2-30, suitable for use up TMDT 2-30, suitable for use TMDT 2-30, suitable for use up
to 900 C (1 650 F) up to 900 C (1 650 F) to 900 C (1 650 F)
Full range accuracy Tobj = 0 to 625 C 2% Tobj = 0 to 635 C 2% 2% of reading or 2 C (4 F) 20 to 500 C: 1% of reading or
of reading or 2 C (4 F) of reading or 2 C (4 F) whichever is greater 1 C (1.8 F) whichever is greater
whichever is greater whichever is greater 500 to 1 000 C: 1,5% of reading
50 to +20 C: 3,5 C (6.3 F)
Environmental limits Operation 0 to 50 C Operation 0 to 50 C Operation 0 to 50 C Operation 0 to 50 C
(32 to 122 F) (32 to 122 F) (32 to 122 F) (32 to 122 F)
10 to 95% relative humidity 10 to 95% relative humidity 10 to 95% relative humidity 10 to 95% relative humidity
Storage 20 to +65 C Storage 20 to +65 C Storage 20 to +65 C Storage 10 to +60 C
(4 to +149 F) (4 to +149 F) (4 to +149 F) (14 to 150 F)
10 to 95% relative humidity 10 to 95% relative humidity 10 to 95% relative humidity 10 to 95% relative humidity
Response time (90%) <1 000 ms <1 000 ms <1 000 ms <300 ms
LCD display resolution 0,1 C/F from 9,9 to ~199,9 0,1 C/F from 9,9 to ~199,9 0,1 C/F from 9,9 to ~199,9 0,1 up to 1 000 ,
otherwise 1 C/F otherwise 1 C/F otherwise 1 C/F otherwise 1
Spectral response 814 m 814 m 814 m 814 m
User selectable backlit No, permanently on On/Off On/Off No, permanently on
display
User selectable laser pointer No, permanently on On/Off On/Off On/Off
Measurement modes Max temperature Max, min, average, differential, Max, min, average, differential, Max, min, average, differential,
probe/IR dual temperature probe/IR dual temperature probe/IR dual temperature
modes modes modes
Alarm modes High and low level alarm level High and low level alarm level High and low level alarm level
with warning bleep with warning bleep with audible alarm
Laser Class 2 Class 2 Class 2 Class 2
Dimensions 195 70 48 mm 195 70 48 mm 203 197 47 mm 205 155 62 mm
(7.7 2.7 1.9 in.) (7.7 2.7 1.9 in.) (8.0 7.7 1.8 in.) (8.1 6.1 2.4 in.)
Packaging Carton box Sturdy carrying case Sturdy carrying case Sturdy carrying case
Carrying case dimensions 530 85 180 mm 530 85 180 mm 530 85 180 mm
(20.9 3.4 7.0 in.) (20.9 3.4 7.0 in.) (20.9 3.4 7.0 in.)
Weight 230 g (0.5 lb) Total: 1 100 g (2.4 lb) Total: 1 300 g (2.9 lb) Total: 1 600 g (2.53 lb)
TKTL 20: 230 g (0.50 lb) TKTL 30: 370 g (0.815 lb) TKTL 40: 600 g (1.32 lb)
Battery 2 AAA Alkaline type IEC LR03 2 AAA Alkaline type IEC LR03 2 AAA Alkaline type IEC LR03 1 Rechargeable Li-ion Battery
Battery lifetime 18 hours 18 hours 140 hours with laser and 4 hours continuous use
backlight off
Otherwise 18 hours
Auto switch off Yes User selectable User selectable User selectable
HVAC functionalities Wet bulb, dew point, humidity,
air temperature
Photo and video mode 640 480 camera, images
(JPEG) and video (3 GP)
Memory/PC connection 310 MB internal memory.
Expandable using micro SD
memory card (8 GB max.)
/ mini USB cable
104
SKF K-type Thermocouple Probes TMDT 2 series
For use with SKF Thermometers TKDT 10, TKTL 20, TKTL 30 and TKTL 40
130
TMDT 2-30 Standard surface probe
8
For hard surfaces such as bearings, bearing housings, engine blocks, oven 900 C 2,3 s
shields, etc. (1 650 F)
130
TMDT 2-34/1.5 Gas and liquid probe
Same as TMDT 2-34 but with thin shank and faster response time. Very 900 C 6,0 s
1,5
flexible, especially suitable for measuring temperature of gases. (1 650 F)
All probes can be used with the SKF digital thermometers TKDT 10, TKTL 20, TKTL 30 and TKTL 40 without recalibration.
105
Thermal imaging
Detect hot spots before they cause you trouble
Using an SKF Thermal camera is a proactive way to help you detect problems before they
occur, increasing uptime and improving safety. They allow you to be able to visualise potential
problems, invisible to the naked eye, by presenting a picture of the heat distribution of an asset.
The thermal image, presented on a large LCD screen, shows you where the temperature is
either too hot or too cold allowing you to pinpoint potential problems fast.
106
Analysis and reporting software suite
Unique SKF software designed by and for real users
Comprehensive analysis and reporting options are simple to use
Easily produce professional results
CW pump motor #6
IR_19
Date created: 02/07/2013 15:30 Global emissivity: 0.96
Location: Reflected temperature: 26.3C
Operator: Ambient temperature: 26.3C
Infrared camera: SKF TKTI 31 Min temperature / emissivity: 22.9C / 0.96
Machine designation: Max temperature / emissivity: 76.7C / 0.96
76.8C
24.4C
Measurements / annotations
IP54
Dust protected
Easy to use
Tactile button feedback allows use with gloves
Simple, but comprehensive, menu structure
Camera, with good weight balance, reduces user fatigue
Live thermal pictures can be displayed on standard TV
monitor (PAL/NTSC)
107
Visual and thermal
TKTI21 TKTI31
Bearings and housings
Belt and chain drives
Conveyor belt bearings
Coupling alignment
Heat exchangers
HVAC
Loose bolts
Pipe insulation
Pumps
Refractory insulation
Steam traps
Tank levels
Valves
Electric motors, inc junction boxes
Electrical cabinet inspections
Electrical connection problems, incl. unbalanced loads, fuses and overloads
Power line connections
Power lines
Powerline capacitors
Transformer bushings
Transformer cooling and electrical
Buildings - indoors - insulation, moisture
Buildings - outdoors - moisture, heat, insulation, energy audits, roofs
108
Technical data
Designation TKTI 21 TKTI 31
Performance
Thermal detector (FPA) 160 120 uncooled FPA microbolometer 380 280 uncooled FPA microbolometer
Display 3.5 in. colour LCD with LED backlight, 3.5 in. colour LCD with LED backlight,
11 colour palettes, thermal or visual image 11 colour palettes, thermal or visual image
Thermal sensitivity NETD 100 mK (0.10 C) at 23 C (73 F) ambient NETD 60 mK (0.06 C) at 23 C (73 F) ambient
and 30 C (86 F) scene temperature and 30 C (86 F) scene temperature
Field of view (FOV) 25 19 25 19
Spectral range 814 microns 814 microns
Theoretical spatial resolution IFOV 2.77 mrad 1.15 mrad
Measureable spatial resolution IFOV 8.31 mrad 3.46 mrad
Accuracy The greater of 2 C or 2% of reading in C The greater of 2 C or 2% of reading in C
Focus Manual, easy turn ring, mininum distance 10 cm (3.9 in.) Manual, easy turn ring, mininum distance 10 cm (3.9 in.)
Visual camera 1.3 Megapixel digital camera 1.3 Megapixel digital camera
Laser pointer Built-in class 2 laser Built-in class 2 laser
Frame rate and image frequency 9 Hz 9 Hz
Measurement
Standard mode 20 to +350 C (4 to +662 F) 20 to +180 C (4 to +356 F)
High temperature mode N/A 100 to 600 C (212 to 1 112 F)
Measurement modes Up to 4 movable spots. Up to 3 movable areas and 2 movable lines (maximum, minimum and average temperatures).
Automatic temperature difference. Hot and cold spots. Visual and audible alarms. Isotherms.
Emissivity correction User selectable 0.1 to 1.0 in steps of 0.01 with reflected and ambient temperature compensation. Emissivity can be
individually adjusted on each cursor. Emissivity table of common surfaces built-in.
Image storage
Medium 2 GB Micro SD card 2 GB Micro SD card
Number Up to 10 000 images on Micro SD card supplied Up to 10 000 images on Micro SD card supplied
Voice annotation Input via built-in microphone for up to 60 seconds Input via built-in microphone for up to 60 seconds
clip per image clip per image
Software Included SKF TKTI Thermal Camerasuite. Comprehensive image analysis and report generation software compatible
with TKTI 21 and TKTI 31, Free updates available on SKF.com
Computer requirements PC with Windows XP, Vista, Windows 7 or above PC with Windows XP, Vista, Windows 7 or above
Connections
PC connection Mini USB connector for image export to PC software Mini USB connector for image export to PC software
(Cable provided) (Cable provided)
External DC input 12 V DC Input connector (DC Charger not provided) 12 V DC Input connector (DC Charger not provided)
Video output 1 Mini-jack output for live image viewing 1 Mini-jack output for live image viewing
(mini-jack to video cable provided) (mini-jack to video cable provided)
Mounting Handheld and tripod mounting 0.25 in. BSW. Handheld and tripod mounting 0.25 in. BSW.
Battery and power
Battery 2 14,8 W, 7,4 V standard camcorder Li-ion batteries. 2 14,8 W, 7,4 V standard camcorder Li-ion batteries.
Rechargeable and field replaceable Rechargeable and field replaceable
Operation time Up to 4 hours continuous operation with 80% brightness Up to 4 hours continuous operation with 80% brightness
Power adapter External 100240 V, 5060 Hz AC battery compact External 100240 V, 5060 Hz AC battery compact
charger with Europe cable, USA, UK and Australian plugs charger with Europe cable, USA, UK and Australian plugs
Charging time 2 hours and 45 minutes 2 hours and 45 minutes
Complete system
Contents Thermal camera TKTI 21 with 2 batteries; AC Battery Thermal camera TKTI 31 with 2 batteries; AC Battery
Charger; Micro SD card (2GB); Mini USB to USB connection Charger; Micro SD card (2GB); Mini USB to USB connection
cable; Mini-jack to video connection cable; Micro SD card to cable; Mini-jack to video connection cable; Micro SD card to
USB adapter; CD containing instructions for use and PC USB adapter; CD containing instructions for use and PC
software; Certificate of calibration and conformance; Quick software; Certificate of calibration and conformance; Quick
start guide (English); Carrying case. start guide (English); Carrying case.
Carrying case dimensions 105 230 345 mm (4.13 9.06 9.65 in.) 105 230 345 mm (4.13 9.06 9.65 in.)
Weight (incl. battery) 1,1 kg (2.42 lb) 1,1 kg (2.42 lb)
109
Pinpoint accuracy combined with measurement versatility
SKF Tachometer Series
The SKF Tachometers are fast and accurate instruments utilizing laser or contact to measure
rotational and linear speeds. Equipped with a laser and a range of contact adapters, they are
versatile instruments that suit a wide range of applications. Having a compact design, they can
be operated with just one hand and are supplied in a sturdy carrying case.
TKRT 10 TKRT 20
Wide speed measurement range: up to 99 999 r/min for laser The user can select the following to measure:
measurement and 20 000 r/min using contact adapters rpm, rps, m, ft or yds per minute or second,
Measurement modes include; rotational speed, total revolutions, length or revolution counting, or
frequency, surface speed and length in both metric and imperial units time interval
Laser can be used for safe and quick, non-contact rotational speed Wide speed range and the various measurement modes make the
measurements at distances up to 0,5 m (20 in.) SKF TKRT 20 suitable for measuring speed in many applications
Large back-lit LCD display enables easy reading in almost all Large angular range of 80 to target facilitates easy measuring in
light conditions areas where straightline access is difficult
Angular range of 45 to target helps facilitate easy measuring The laser optical system allows easy and quick measurements at a
Up to 10 readings can be stored for later reference safe distance from rotating machinery
The large inverting LCD display facilitates easy reading, even when
pointing the unit down into the machinery
The SKF TKRT 20 can also be equipped with a remote laser sensor,
which is optionally available
110
The laser optical system allows
easy and quick measurements
at a safe distance from rotating
machinery.
Technical data
Designation TKRT 10 TKRT 20
Display 5 digit LCD backlit display Inverting vertical 5 digit LCD
Memory 10 readings memories Last reading held for 1 minute
Measurement
Optical modes r/min, hertz r/min and r/s (also count and time interval)
Contact modes r/min, metres, inches, yards, feet, per min, hertz r/min and r/s, metres, yards, feet, per min and per sec
Count modes total revs, metres, feet, yards total revs, metres, feet, yards
Sampling time 0,5 seconds (over 120 r/min) 0,8 seconds or time between pulses
0,1 seconds auto-selection in max or min capture mode
Linear speed 0,2 to 1 500 metres/min (4 500 ft/min) 0,3 to 1 500 metres/min (4 500 ft/min) or equivalent in seconds
Optical measurement
Rotational speed range 3 to 99 999 r/min 3 to 99 999 r/min
Accuracy 0,05% of reading 1 digit 0,01% of reading 1 digit
Measuring distance 50 to 500 mm (1.9 to 19.7 in.) 50 to 2 000 mm (1.9 to 78.7 in.)
Angle of operation 45 80
Laser sensor 1 built-in class 2 laser 1 built-in class 2 laser
Remote laser sensor N/A Optional TMRT 1-56
Contact measurement
Rotational speed range 2 to 20 000 r/min Max. 50 000 r/min for 10 sec
Accuracy 1% of reading 1 digit 1% of reading 1 digit
Contact adaptors Included with conical tip, conical recess and wheel Included with r/min cone and removable metric wheel assembly
Battery 1 9 V alkaline type IEC 6F22 4 AAA alkaline type IEC LR03
Operation time 12 hours continuous use 24 hours continuous use
Product dimensions 160 60 42 mm (6.3 2.4 1.7 in.) 213 40 39 mm (8.3 1.5 1.5 in.)
Product weight 160 g (0.35 lb) 170 g (0.37 lb)
Carrying case dimensions 260 85 180 mm (10.3 3.4 7.0 in.) 260 85 180 mm (10.3 3.4 7.0 in.)
Operating temperature 0 to 50 C (32 to 122 F) 0 to 40 C (32 to 104F)
Storage temperature 10 to +50 C (14 to 122 F) 10 to +50 C (14 to 122 F)
Relative humidity 10 to 90% RH non-condensing 10 to 90% RH non-condensing
IP rating IP 40 IP 40
111
Easy, cost effective inspection in a flash
SKF Stroboscopes TKRS series
The SKF Stroboscopes, TKRS 10 and TKRS 20 are portable, compact, easy-to-use
stroboscopes that enable the motion of rotating or reciprocating machinery to appear frozen.
They allow such applications as fan blades, couplings, gear wheels, machine tool spindles and
belt drives to be inspected while running. TKRS stroboscopes are useful for ODR programmes
and are an essential instrument for maintenance technicians.
TKRS 10 TKRS 20
Flash rates of up to 12 500 flashes per minute cover a wide Low energy consuming LED light source lets the rechargeable
range of applications power pack to typically operate for at least twelve hours
Easy to read LCD display Bright and powerful flash gives a good target illumination at a
Xenon flashtube source lasts for at least 100 million flashes distance, with a focused viewing area, and is ideal for outdoor use
Supplied with an extra flashtube to minimise unit downtime Flash rates of up to 300 000 flashes per minute cover most high
Rechargeable power pack alllows up to 2,5 hours of use speed applications. For routine inspections, the powerful lamp mode
between charging is useful
A remote optical sensor is included enabling the flash rate to be
easily triggered, and also enables the stroboscope to be used as
a tachometer
Easy to read LCD display shows user settings, and enables the ten
The TKRS series have the following features: user programmable flash rate memories to be quickly recalled
Ergonomic controls enable the flash rate to be set in a matter Using the optional cable TKRS C1, the TKRS 20 can be connected
of seconds to a SKFMicrolog
Phase shift mode enables the viewing of the object of interest to
be rotated to the correct position for viewing; especially useful
for gear wheels and fan blade inspection
For ease of use for extended periods, they are equipped with a
tripod mounting thread
Supplied in a sturdy carrying case with universal charger
112
Technical data
113
Fast and easy inspection with video function
SKF Endoscopes TKES 10 series
SKF Endoscopes are first line inspection tools that can be used for internal
inspection of machinery. They help minimise the need to disassemble
machinery for inspection, saving time and money. The compact display unit,
with 3.5 backlit screen, allows images and video to be saved and recalled,
or to be downloaded and shared with others. Three different models cater to
most needs and are equipped with powerful variable LED lighting allowing
inspections in dark locations.
114
Photos and videos can be transferred to PC using the USB cable provided.
Technical data
Technical data
Display Unit
Power 5 V DC
Display 3.5" TFT LCD monitor 320 240 pixels
Interface Mini USB 1.1 / AV out / AV in/
Battery (not user serviceable) Rechargeable Li-Polymer battery (3.7 V).
Typically 4 hours operation after a 2 hour charge.
Video out format NTSC & PAL
Recording medium SD card 2 GB supplied storage capacity 50 000 photos,
or 120 minutes video. (SD/SDHC cards up to 32 GB can be used)
Output resolution (H V)
Still image (JPEG) 640 480 pixels
Video recording format (ASF) 320 240 pixels
Temperature range
Working and storage -20 to +60 C (4 to +140 F)
Battery charging temperature range 0 to 40 C (32 to 104 F)
Functions Snapshot, video recording, picture & video review on LCD screen,
TV Out, transfer of picture & video from SD card to PC
115
Easily pinpoints bearing and machine noise
SKF Electronic Stethoscope TMST 3
The SKF TMST 3 is a high quality instrument enabling the determination of
troublesome machine parts by the detection of machine noises. TMST 3 includes
a headset, two different length probes (70 and 220 mm) and a pre-recorded
audio CD demonstrating the most common encountered troublesome machine
noises, all supplied complete in a sturdy carrying case.
Technical data
Designation TMST 3
Frequency range 30 Hz15 kHz Battery 4 AAA Alkaline type IEC LR03 (included)
Operating temperature 10 to +45 C (14 to 113 F) Battery lifetime 30 hours (continuous use)
Output volume Adjustable in 32 levels Dimensions handset 220 40 40 mm (8.6 1.6 1.6 in.)
Led indicator Power on Probe length 70 and 220 mm (2.8 and 8.7 in.)
Sound volume Carrying case dimensions 360 110 260 mm (14.2 4.3 10.2 in.)
Battery low
Weight
Maximum recorder output 250 mV Total weight 1 600 g (3.5 lb)
Headset 48 ohm (with ear defender) Instrument 162 g (0.35 lb)
Headset 250 g (0.55 lb)
Auto switch off Yes, after 2 min.
116
Easy noise level measurement
SKF Sound Pressure Meter TMSP 1
The SKF TMSP 1 is a high quality, handheld instrument for measuring the sound
level in decibels. The environmental noise is picked up by the microphone and
then processed by the handset. The noise can be monitored both quantitatively
and qualitatively. The SKF Sound Pressure Meter is supplied in a carrying case
complete with windshield, calibration screwdriver, jack for external outputs and
an alkaline battery.
Technical data
Designation TMSP 1
Frequency range 31,5 Hz to 8 KHz Dynamic range 50 dB
Measuring level range 30 to 130 dB Power supply 9 V Alkaline type IEC 6LR61
Display LCD Power life 50 hours (with alkaline battery)
Digital display 4 digits, Resolution: 0,1 dB, Operation temperature 0 to 40 C (32 to 104 F)
Display update: 0,5 s Operation humidity 10 to 90% relative humidity
Analogue display 50 segments bar-graph Operation altitude Up to 2 000 m (6 560 ft) above sea level
Resolution: 1 dB
Display update: 100 ms Dimensions 275 64 30 mm (10.8 2.5 1.2 in.)
Time weighting Fast (125 ms), Slow (1 s) Carrying case dimensions 530 85 180 mm (20.9 3.4 7.0 in.)
Level ranges Lo = 30~80 dB, Med = 50~100 dB, Weight 285 g (0.76 lb) including battery
Hi = 80~130 dB, Auto = 30~130 dB Total weight (incl.case) 1 100 g (2.4 lb)
Accuracy 1,5 dB (ref 94 dB at 1 KHz)
Conformity Fulfills IEC651 type 2, ANSI S1.4 type 2
for sound level meters
117
Quick and easy detection of air leaks
SKF Ultrasonic Leak Detector TMSU 1
The SKF TMSU 1 is a high quality, user-friendly instrument enabling the detection of air leaks
by means of ultrasound. Leaks are caused by fluid flowing from a high pressure environment to
a low pressure environment, creating turbulence. The turbulence generates high frequency
sounds (so called ultrasound) that can be detected by SKF TMSU 1. The operator simply guides
the instrument to the loudest point, which helps locate the leak location.
Technical data
Designation TMSU 1
Amplification 7 levels: 20, 30, 40, 50,
60, 70 and 80 dB
Ultrasound sensor 19 mm (0.75 in.) diameter
central frequency of 40 kHz
Detected frequencies 38,4 kHz, 2 kHz (3 dB)
Power Two alkaline AA batteries, 1,5 V.
Rechargeable batteries can also be used
Battery life Typically 20 hours
Dimensions Body: 170 42 31 mm
(6.70 1.65 1.22 in.)
Flexible tube length: 400 mm (15.75 in.)
Weight 0,4 kg (0.9 lb) incl. batteries
Carrying case dimensions 530 110 360 mm (20.9 4.3 14.2 in.)
Operating
temperature range 10 to +50 C (14 to 122 F)
Technical data
Lubricant degradation Designation TKED 1
caused by electrical Power supply 4,5 V
3 AAA Alkaline type IEC LR03
discharge currents
Time control
pre-sets 10 or 30 seconds
default indefinite
Operational and storage 0 to 50 C (32 to 122 F)
temperature 20 to +70 C (4 to +158 F)
Ingress protection level IP 55
Display LCD counter range:
Fluting marks characteristic 0 to 99 999 discharges.
User selectable backlight and low
of electrical erosion in
battery warning
bearings
Carrying case dimensions 260 85 180 mm
(10.3 3.4 7.0 in.)
Total case and contents weight 0,4 kg (0.88 lb)
119
Reliability meets affordability
SKF Machine Condition Indicator CMSS 200
The SKF Machine Condition Indicator is an economical vibration sensor and
temperature indicator for monitoring non-critical machines. It is ideal for
machinery with constant operating conditions, which has not been previously
monitored. The device can be compared to the check engine light in a car.
Technical data
Designation CMSS 200
Velocity measurement 10 Hz to 1 kHz / minimum speed Enclosure White durable polymer cap PC/PET Blend,
900 r/min Bayer Makroblend UT 1018-1000 and a
stainless steel base
Bearing measurement Enveloped acceleration to enable an
early Stage 3 bearing defect to be Weight 120 g (4.2 oz.)
detected for speeds between 900 and
3 600 r/min
Machine surface temperature 20 to +105 C (5 to +220 F)
measurement range
Rating IP 69K, for use in adverse industrial
environments
Alarm system Three LEDs (green, red and orange)
Mounting Stud mounted or epoxy mount
(stud not included in 10 or 50 pack) 1/4-28
68 mm
mounting hole (2.7 in.)
Internal operating 20 to +85 C (5 to +185 F)
temperature range
Wake up schedule Eight times per day
Battery life 3 years (with one unacknowledged alarm)
Battery type Lithium battery 3,6 V, single use,
non-replaceable
34 mm (1.3 in.)
120
Machine monitoring, made simple
SKF Machine Condition Advisor CMAS 100-SL
Both novice users and experts can easily, quickly, and accurately check the condition of
rotating equipment throughout their facility. Equipping your maintenance and operation
personnel with this rugged, ergonomic and easy-to-use instrument can help to provide
early warning of potential machine problems before a costly failure occurs.
Technical data
Designation CMAS 100-SL
Vibration pick-up Internal: Integrated piezoelectric acceleration Humidity 95% relative humidity, non-condensing
External: Accepts a standard 100 mV/g Ingress protection IP 54
constant current accelerometer
Approvals CE (Certified Engineering)
Measurements
Drop test 2 m (6.6 ft.)
Velocity Range: 0,7 to 65,0 mm/s (RMS)
0.04 to 3.60 in./s (equivalent Peak) Weight 125 g (4.4 oz.)
meets ISO 10816 Dimensions 200 47 25 mm (7.9 1.85 1 in.)
Frequency: 10 to 1 000 Hz,
meets ISO 2954 Battery capacity 550 mAh
122
Lubrication
Lubricants 132
Automatic grease dispensing tools 158 Dismounting Buy a bearing
Manual grease dispensing tools 172
Transfer tools 179
Accessories 180
Storage tools 182 Basic
Oil inspection and dispensing 183 condition Mounting
Lubrication analysis tools 186 monitoring
Lubrication software 188
Alignment Lubrication
123
Lubrication management
Poor lubrication accounts for more than 36% of premature bearing failures
Include contamination, and this number rises to well above 50%.
The importance of proper lubrication and cleanliness is self-evident
in the determination of bearing life.
The right lubricant, in the right amount, reaches the right point
at the right time using the right method
Increase Reduce
Productivity Energy consumption due to friction
Reliability Heat generation due to friction
Availability and durability Wear due to friction
Machine uptime Noise due to friction
Service intervals Downtime
Safety Operating expenses
Health Product contamination
Sustainability Maintenance and repair costs
Lubricant consumption
Corrosion
124
Lubricant Lubricant Lubricant Lubricant Lubricant
selection storage transfer dispensing disposal
Lubricant monitoring
Selecting a suitable grease for a particular bearing is a crucial step if For the correct lubricant dispensing, consider the range of SKF Grease
the bearing is to meet design expectations in its application. Use the Guns and SKF range of single and multi point lubricators. SKF DialSet
SKF LubeSelect to select the right lubricant for your application. helps you select the right lubricator settings for the application.
During storage, maintenance and transfer steps, the lubricant can easily For the monitoring of the lubricant, SKF offers the following tools:
get contaminated due to lack of lubrication knowledge or simply lack of SKF Oil Levellers, SKF Oil Check Monitor and SKF Grease Test Kit.
attention. To minimize the risks of lubricant contamination in storage and
transfer, we recommend the use of the Oil storage station and Oil
handling containers LAOS series. For the transfer of greases, we offer
an extensive range of SKF Grease Pumps, SKF Grease Filler Pumps and
SKF Bearing Packer.
Lubrication management
Just as asset management takes maintenance to a higher level, a lubrication management
approach allows lubrication to be seen from a wider point of view. This approach helps to
effectively increase machine reliability at a lower overall cost.
Normally implies one Detailed assessment. Formulation of Execution of the Reassessment and
day of assessment and Normally implies five specific activities proposed activities implementation of
provides an overview days and provides a additional improvement
on the lubrication thorough analysis of the proposals
programme maturity lubrication programme
125
SKF lubricant selection
This knowledge has led SKF, in many cases, to set industry standards
in bearing lubricant testing. Emcor, ROF, ROF+, V2F, R2F and Bequiet
are just some of the multiple tests developed by SKF to assess the
performance of lubricants under bearing operating conditions. Many
of them are widely used by lubricant manufacturers worldwide.
126
Basic bearing grease selection
Generally use if:
Unless:
Biodegradable,
LGGB 2 Biodegradable
demands for low toxicity
Note: For areas with relatively high ambient temperatures, use LGMT 3 instead of LGMT 2
For special operating conditions, refer to the SKF bearing grease selection chart
127
SKF bearing grease selection chart
Temp. Speed
Temperature range 1)
Grease Description Application examples LTL HTPL
Pellet presses
Food compatible 40 C 140 C
LGFQ 2 High load
Mills
(40 F) (285 F)
L to H VL to M
Mixers
Wind turbine blade and Wind turbine blade and yaw 40 C 120 C
LGBB 2 yaw bearing grease slewing bearings (40 F) (250 F)
L to M VL
Jaw crushers
High viscosity plus 20 C 120 C
LGEM 2 solid lubricants
Construction machinery
(5 F) (250 F)
M VL
Vibrating machinery
Trunnion bearings
Extremely high viscosity 10 C 120 C
LGEV 2 with solid lubricants
Support and thrust rollers on rotary kilns and dryers
(15 F) (250 F)
M VL
Slewing ring bearings
Electric motors
High performance 40 C 150 C
LGHP 2 polyurea grease
Fans, even at high speed
(40 F) (300 F)
M to H M to H
High speed ball bearings at medium and high temperatures
1) LTL = Low Temperature Limit 3) LGGB 2 can withstand peak temperatures of 120 C (250 F)
HTPL = High Temperature Performance Limit 4) LGWA 2 can withstand peak temperatures of 220 C (430 F)
2) mm2/s at 40 C (105 F) = cSt. 5) LGHB 2 can withstand peak temperatures of 200 C (390 F)
128
Load Thickener / NLGI Base oil Vertical Fast outer Oscillating Severe Shock load Rust
Base Oil viscosity 2) shaft ring rotation movements Vibrations or frequent inhibiting
start up properties
Lithium soap/
L to M
mineral oil
2 110
+ +
Lithium soap/
L to M
mineral oil
3 125
+ +
Special requirements
Aluminium complex/
L to M
medical white oil
2 150
+
Complex calcium
L to VH
sulphonate/PAO
12 320
+ + + +
Lithium complex soap/
M to H
synthetic PAO oil
2 68
+ + + +
Lithium soap/
L
synthetic PAO oil
2 18
Low temperatures
Lithium soap/
H
mineral oil
1 200
+ + +
Complex calcium
L to H sulphonate/ synthetic
PAO oil/ mineral oil
12 80
+ + + +
Lithium soap/
H to VH 2 500
+ + + +
High loads
mineral oil
Lithium-calcium soap/
H to VH
mineral oil
2 1020
+ + + +
Complex calcium
L to VH sulphonate/
mineral oil
2 425
+ + + + +
High temperatures
Di-urea/
L to M
mineral oil
23 96
+ +
PTFE / synthetic
H to VH fluorinated
polyether oil
2 460
+
PTFE/ synthetic
H to VH fluorinated
polyether oil
2 400
+ +
= Suitable + = Recommended
129
LGMT 2 LGMT 3 LGEP 2 LGWA 2 LGGB 2 LGFP 2 LGFQ 2
DIN 51825 code K2K-30 K3K-30 KP2G-20 KP2N-30 KPE 2K-40 K2G-20 KP1/2N-40
Colour Red brown Amber Light brown Amber Off white Transparent Brown
Base oil type Mineral Mineral Mineral Mineral Synthetic Medical Synthetic (PAO)
(Ester) white oil
Operating temperature range 30 to +120 C 30 to +120 C 20 to +110 C 30 to +140 C 40 to +90 C 20 to +110 C 40 to +140 C
(20 to +250 F) (20 to +250 F) (5 to +230 F) (20 to +285 F) (40 to +195 F) (5 to +230 F) (40 to +284 F)
Dropping point DIN ISO 2176 >180 C >180 C >180 C >250 C >170 C >250 C >300 C
(>355 F) (>355 F) (>355 F) (>480 F) (>340 F) (>480 F) (>570 F)
Mechanical stability
Roll stability, 50 hrs at 80 C, 101 mm +50 max. 295 max. +50 max. +50 max. change +70 max. 20 to +30 max.
V2F test M 'M' 'M' 'M' (350 max.)
Corrosion protection
Emcor: standard ISO 11007 00 00 00 00 00 00 1) 00
water washout test 00 00 00 00 1)
salt water test (100% seawater) 01 1) 11 1) 00
Water resistance
DIN 51 807/1, 3 hrs at 90 C 1 max. 2 max. 1 max. 1 max. 0 max. 1 max. 1 max.
Oil separation
DIN 51 817, 7 days at 40 C, static, % 16 13 25 15 0,83 15 3 max.
Lubrication ability
R2F, running test B at 120 C Pass Pass Pass Pass, Pass, Pass
100 C (210 F) 100 C (210 F) 1)
R2F, cold chamber test, 30 C, +20 C
Copper corrosion 2 max. 2 max. 2 max. 2 max. 1 max. 1b max.
DIN 51 811 110 C (230 F) 130 C (265 F) 110 C (230F) 100 C (210F) 120 C (250 F) 100 C (210F)
EP performance
Wear scar DIN 51350/5, 1 400 N, mm 1,4 max. 1,6 max. 1,8 max. 1 max.
4ball test, welding load DIN 51350/4, N 2 800 min. 2 600 min. 2 600 min. 1 100 min. >4 000
Fretting corrosion
ASTM D4170 FAFNIR test at +25 C mg 5,7 1) 0,8 1)
1) Typical value
Special requirements
KP2G-40 K2G-50 KP1G-30 KP2G-40 KPF2K-20 KPF2K-10 KP2N-20 K2N-40 KFK2U-30 KFK2U-40
2 2 1 12 2 2 2 23 2 2
Lithium Lithium Lithium Complex calcium Lithium Lithium/ Complex calcium Diurea PTFE PTFE
complex sulphonate calcium sulphonate
Yellow Beige Brown Yellow Black Black Brown Blue Off white Off white
Synthetic (PAO) Synthetic (PAO) Mineral Synthetic (PAO)/ Mineral Mineral Mineral Mineral Synthetic Synthetic
Mineral (fluorinated (fluorinated
polyether) polyether)
40 to +120 C 50 to +110 C 30 to +110 C 40 to +110 C 20 to +120 C 10 to +120 C 20 to +150 C 40 to +150 C 30 to +240 C 40 to +260 C
(40 to +250 F) (60 to +230 F) (20 to +230 F) (40 to +230 F) (5 to +250 F) (15 to 250 F) (5 to +300 F) (40 to +300 F) (22 to +464 F) (40 to +500 F)
>200 C >180 C >170 C >300 C >180 C >180 C >220 C >240 C >300 C >300 C
(390 F) (>355 F) (>340 F) (>570 F) (>355 F) (>355 F) (>430 F) (>465 F) (>570 F) (>570 F)
265295 265295 310340 280310 265295 265295 265295 245275 265295 265295
+50 max. +50 max. +50 max. +30 max 325 max. 325 max. 20 to +50 365 max. 271 1)
(325 max.)
+50 max. +50 max. 345 max. +50 max. 20 to +50 365 max. 30 max.
M M change 130 C (265 F)
M
00 01 00 00 00 00 00 00 00 1) 11 max.
00 00 00 00 1) 00 00
01 1) 00 1) 00 1) 00 1) 00
1 max. 1 max. 1 max. 1 max. 1 max. 1 max. 1 max. 1 max. 1 max. 0 max.
1 max. 1 max. 2 max. 2 max. 2 max. 1 max. 2 max. 1 max. 1 max. 1 max.
120 C (250 F) 100 C (210 F) 90 C (>195 F) 100 C (210 F) 100 C (210 F) 100 C (210 F) 150 C (300 F) 150 C (300 F) 100 C (210 F) 1) 150 C (300 F)
>1 000, 1 824 1), >1 000, 1 000 min. >700 at 220 C >1 000 1) at
20 000 r/min. 110 C (230 F) 130 C (265 F) 150 C (300 F) (430 F) 220 C (428 F)
100C (210 F)
0,4 1) 1,8 max. 1,5 max. 1) 1,4 max. 1,2 max. 0,86 1)
5 500 1) 2 000 min. 3 200 min. 1) 4 000 min. 1) 3 000 min. 3 000 min. 4 000 min. 8 000 min. 8 000 min.
High loads
Typical applications
Agricultural equipment
Automotive wheel bearings
Conveyors
Small electric motors
Industrial fans
Technical data
Designation LGMT 2/(pack size)
DIN 51825 code K2K-30 Corrosion protection
Emcor:
NLGI consistency class 2
standard ISO 11007 00
Thickener Lithium water washout test 00
Colour Red brown salt water test (100% seawater) 01 1)
1) Typical value
132
LGMT 3 SKF General Purpose Industrial and Automotive Bearing Grease
SKF LGMT 3 is mineral oil based, lithium soap thickened
grease. This premium quality, general purpose grease is
suitable for a wide range of industrial and automotive
applications requiring stiff grease.
Typical applications
Bearings >100 mm (3.9 in.) shaft size
Outer bearing ring rotation
Vertical shaft applications
Continuous high ambient temperatures >35 C (95 F)
Propeller shafts
Agricultural equipment
Car, truck and trailer wheel bearings
Large electric motors
Technical data
Designation LGMT 3/(pack size)
DIN 51825 code K3K-30 Corrosion protection
Emcor: standard ISO 11007 00
NLGI consistency class 3
water washout test 00
Thickener Lithium
Water resistance
Colour Amber DIN 51 807/1,
Base oil type Mineral 3 hrs at 90 C 2 max.
133
LGEP 2 SKF High Load, Extreme Pressure Bearing Grease
SKF LGEP 2 is mineral oil based, lithium soap thickened
grease with extreme pressure additives. This grease
provides good lubrication in general applications subjected
to harsh conditions and vibrations.
Typical applications
Pulp and paper making machines
Jaw crushers
Dam gates
Work roll bearings in steel industry
Heavy machinery, vibrating screens
Crane wheels, sheaves
Slewing bearings
Technical data
Designation LGEP 2/(pack size)
DIN 51825 code KP2G-20 Water resistance
DIN 51 807/1,
NLGI consistency class 2
3 hrs at 90 C 1 max.
Thickener Lithium
Oil separation
Colour Light brown DIN 51 817,
Base oil type Mineral 7 days at 40 C, static, % 25
1) Typical value
134
SKF High Load, Extreme Pressure,
LGWA 2
Wide Temperature Range Bearing Grease
SKF LGWA 2 is a premium quality mineral oil based,
lithium complex grease with extreme pressure (EP)
performance. LGWA 2 is recommended for general
industrial and automotive applications, when loads or
temperatures exceed the range of general purpose
greases.
Typical applications
Wheel bearings in cars, trailers and trucks
Washing machines
Fan and electric motors
Technical data
Designation LGWA 2/(pack size)
DIN 51825 code KP2N-30 Water resistance
DIN 51 807/1,
NLGI consistency class 2
3 hrs at 90 C 1 max.
Thickener Lithium complex
Oil separation
Colour Amber DIN 51 817,
Base oil type Mineral 7 days at 40 C, static, % 15
1) Typical value
135
LGGB 2 SKF Biodegradable Bearing Grease
SKF LGGB 2 is a biodegradable, low toxicity, synthetic ester
oil based grease, using a lithium-calcium thickener. Its
special formulation makes it most suitable for applications
where environmental contamination is a concern.
Typical applications
Agricultural and forestry equipment
Construction and earthmoving equipment
Mining and conveying equipment
Water treatment and irrigation
Locks, dams, bridges
Linkages, rod ends
Technical data
Designation LGGB 2/(pack size)
DIN 51825 code KPE 2K-40 Corrosion protection
Emcor: standard ISO 11007 00
NLGI consistency class 2
Water resistance
Thickener Lithium/calcium
DIN 51 807/1, 3 hrs at 90 C 0 max.
Colour Off white
Oil separation
Base oil type Synthetic ester DIN 51 817, 7 days at 40 C, static, % 0,83
Operating temperature range 40 to +90 C Lubrication ability
(40 to +195 F) R2F, running test B at 120 C Pass at 100 C (210 F) 1)
Dropping point DIN ISO 2176 >170 C (>340 F) Rolling bearing grease life
Base oil viscosity R0F test L50 life at 10 000 r/min., hrs >300 at 120 C (250 F)
40 C, mm2/s 110 EP performance
100 C, mm2/s 13 Wear scar DIN 51350/5, 1 400 N, mm 1,8 max.
Penetration DIN ISO 2137 4ball test, welding load DIN 51350/4, N 2 600 min.
60 strokes, 101 mm 265295 Available pack sizes 420 ml cartridge
100 000 strokes, 101 mm +50 max. (325 max.) 5, 18, 180 kg
Mechanical stability SKF SYSTEM 24 (LAGD)
Roll stability, 50 hrs at 80 C, 101 mm +70 max. (350 max.) Shelf life 2 years
1) Typical value
136
LGBB 2 SKF Wind Turbine Blade and Yaw Bearing Grease
SKF LGBB 2 is a lithium complex/synthetic PAO oil based
grease specially designed for extreme conditions involving
very low speeds, high loads, low temperatures and
oscillating conditions. This grease provides proper
lubrication whether the turbine is operating or in stand-
still mode, installed onshore, offshore, or in cold climate
areas.
Typical applications
Wind turbine blade and yaw bearing applications
Technical data
Designation LGBB 2/(pack size)
DIN 51825 code KP2G-40 Water resistance
DIN 51 807/1,
NLGI consistency class 2
3 hours at 90 C 1 max.
Thickener Lithium complex
Oil separation
Colour Yellow DIN 51817,
Base oil type Synthetic (PAO) 7 days at 40 C, static, % 4 max, 2,5 1)
Operating temperature range 40 to +120 C Copper corrosion
(40 to +250 F) DIN 51 811 1 max. at 120 C (250 F)
Dropping point DIN ISO 2176 >200 C (390 F) EP performances
Wear scar DIN 51350/5, 1400 N, mm 0,4 1)
Base oil viscosity
4-ball test, welding load DIN 51350/4, N 5 500 1)
40 C, mm2/s 68
Rolling bearing lubrication ability
Penetration DIN ISO 2137
Fe8, DIN 51819,
60 strokes, 101 mm 265295
80 kN, 80 C, C/P 1.8, 500 h pass
100 000 strokes, 101 mm +50 max.
False brinellng resistance
Mechanical stability
ASTM D4170 FAFNIR test, mg 01 1)
Roll stability, 50h at 80 C, 101 mm +50 max.
Avalaible packsizes 420 ml cartridge
Corrosion protection
5, 18, 180 kg
Emcor: Standard ISO 11007 00
Salt water test (100% sea water) 01 1)
1) Typical value
137
LGLT 2 SKF Low Temperature, Extremely High Speed Bearing Grease
SKF LGLT 2 is a fully synthetic oil based grease using
lithium soap. Its unique thickener technology and
low viscosity oil (PAO) provide excellent lubrication
performances at low temperatures 50 C (60 F)
and extremely high speeds (n dm values of 1,6 106
can be reached).
Typical applications
Textile spinning spindles
Machine tool spindles
Instruments and control equipment
Small electric motors used in medical and dental equipment
In-line skates
Printing cylinders
Robots
Technical data
Designation LGLT 2/(pack size)
DIN 51825 code K2G-50 Water resistance
DIN 51 807/1,
NLGI consistency class 2
3 hrs at 90 C 1 max.
Thickener Lithium
Oil separation
Colour Beige DIN 51 817,
Base oil type Synthetic (PAO) 7 days at 40 C, static, % <4
Dropping point DIN ISO 2176 >180 C (>355 F) Rolling bearing grease life
R0F test >1 000,
Base oil viscosity L50 life at 10 000 r/min., hrs 20 000 r/min. at 100C (210 F)
40 C, mm2/s 18
100 C, mm2/s 4,5 EP performance
4ball test,
Penetration DIN ISO 2137 welding load DIN 51350/4, N 2 000 min.
60 strokes, 101 mm 265295
100 000 strokes, 101 mm +50 max. Available pack sizes 180 g tube
0.9, 25, 170 kg
Corrosion protection
Emcor: standard ISO 11007 01
138
LGWM 1 SKF Extreme Pressure Low Temperature Bearing Grease
SKF LGWM 1 is a low consistency mineral oil based grease,
using a lithium soap and containing extreme pressure
additives. It is extremely suitable for the lubrication of
bearings operating under both radial and axial loads.
Typical applications
Wind turbine main shafts
Screw conveyors
Centralised lubrication systems
Spherical roller thrust bearing applications
Technical data
Designation LGWM 1/(pack size)
DIN 51825 code KP1G-30 Water resistance
DIN 51 807/1,
NLGI consistency class 1
3 hrs at 90 C 1 max.
Thickener Lithium
Oil separation
Colour Brown DIN 51 817,
Base oil type Mineral 7 days at 40 C, static, % 813
1) Typical value
139
LGWM 2 SKF High Load, Wide Temperature Bearing Grease
SKF LGWM 2 is a synthetic-mineral oil based grease using
the latest complex calcium sulphonate thickener
technology. It is suitable for applications subjected to high
loads, wet environments and fluctuating temperatures.
Typical applications
Wind turbine mains shafts
Heavy duty off road applications
Snow exposed applications
Marine and offshore applications
Spherical roller thrust bearing applications
Technical data
Designation LGWM 2/(pack size)
DIN 51825 code KP2G-40 Water resistance
DIN 51 807/1,
NLGI consistency class 12
3 hrs at 90 C 1 max.
Thickener Complex calcium
Oil separation
sulphonate
DIN 51 817,
Colour Yellow 7 days at 40 C, static, % 3 max.
Base oil type Synthetic (PAO)/ Mineral Lubrication ability
Operating temperature range 40 to +110 C R2F, running test B at 120 C Pass at 140 C (285 F)
(40 to +230 F) R2F, Cold chamber test (+20 C) Pass
R2F, Cold chamber test (30 C) Pass
Dropping point DIN ISO 2176 >300 C (>570 F)
Copper corrosion
Base oil viscosity DIN 51 811 2 max. at 100 C (210 F)
40 C, mm2/s 80
100 C, mm2/s 8,6 Rolling bearing grease life
R0F test
Penetration DIN ISO 2137 L50 life at 10 000 r/min., hrs 1 824 1) at 110 C (230 F)
60 strokes, 101 mm 280310
100 000 strokes, 101 mm +30 max. EP performance
Wear scar DIN 51350/5, 1 400 N, mm 1,5 max. 1)
Mechanical stability 4ball test, welding load DIN 51350/4, N 4 000 min. 1)
Roll stability,
50 hrs at 80 C, 101 mm +50 max. Fretting corrosion
ASTM D4170 FAFNIR test at +25 C, mg 5,2 1)
Corrosion protection ASTM D4170 FAFNIR test at 20 C, mg 1,1 1)
Emcor: standard ISO 11007 00
water washout test 00 Available pack sizes 420 ml cartridge
salt water test (100% seawater) 00 1) 5, 18, 50, 180 kg
SKF SYSTEM 24
(LAGD/TLSD), TLMR
1) Typical value
140
LGEM 2 SKF High Viscosity Bearing Grease with Solid Lubricants
SKF LGEM 2 is a high viscosity, mineral oil based grease
using a lithium soap. Its content of molybdenum disulphide
and graphite provides extra protection for harsh applications
subjected to high loads, heavy vibrations and slow rotations.
Typical applications
Rolling element bearings running at low speed and very high loads
Jaw crushers
Track laying machines
Lift mast wheels
Building machines such as mechanical rams, crane arms and
crane hooks
Technical data
Designation LGEM 2/(pack size)
DIN 51825 code KPF2K-20 Corrosion protection
Emcor: standard ISO 11007 00
NLGI consistency class 2
water washout test 00
Thickener Lithium
Water resistance
Colour Black DIN 51 807/1,
Base oil type Mineral 3 hrs at 90 C 1 max.
141
LGEV 2 SKF Extremely High Viscosity Bearing Grease with Solid Lubricants
SKF LGEV 2 is a mineral oil based grease, using a lithium-
calcium soap. Its high content of molybdenum disulphide
and graphite, in conjunction with an extremely high
viscosity oil, provide outstanding protection under the
harshest conditions involving high loads, slow rotations
and severe vibrations.
Typical applications
Trunnion bearings on rotating drums
Support and thrust rollers on rotary kilns and dryers
Bucket wheel excavators
Slewing ring bearings
High pressure roller mills
Crushers
Technical data
Designation LGEV 2/(pack size)
DIN 51825 code KPF2K-10 Corrosion protection
Emcor: standard ISO 11007 00
NLGI consistency class 2
water washout test 00 1)
Thickener Lithium/calcium salt water test (100% seawater) 00 1)
Colour Black Water resistance
Base oil type Mineral DIN 51 807/1,
3 hrs at 90 C 1 max.
Operating temperature range 10 to +120 C
(15 to 250 F) Oil separation
DIN 51 817,
Dropping point DIN ISO 2176 >180 C (>355 F) 7 days at 40 C, static, % 15
Base oil viscosity Copper corrosion
40 C, mm2/s 1 020 DIN 51 811 1 max. at 100 C (210 F)
100 C, mm2/s 58
EP performance
Penetration DIN ISO 2137 Wear scar DIN 51350/5, 1 400 N, mm 1,2 max.
60 strokes, 101 mm 265295 4ball test, welding load DIN 51350/4 3 000 min.
100 000 strokes, 101 mm 325 max.
Available pack sizes 35 g tube
Mechanical stability 420 ml cartridge
Roll stability, 72 hrs at 100 C, 101 mm +50 max. 5, 18, 50, 180 kg
V2F test M TLMR
1) Typical value
142
LGHB 2 SKF High Load, High Temperature, High Viscosity Bearing Grease
SKF LGHB 2 is a high viscosity, mineral oil based grease,
using the latest complex calcium-sulphonate soap
technology. Formulated to withstand high temperatures
and extreme loads, it is suitable for a wide range of
applications, especially in the cement, mining and metals
segments. This grease contains no additives and the
extreme pressure properties arise from the soap structure.
Typical applications
Steel on steel plain bearings
Pulp and paper making machines
Asphalt vibrating screens
Continuous casting machines
Sealed spherical roller bearings operating up to 150 C (300 F)
Work roll bearings in steel industry
Mast rollers of fork lift trucks
Technical data
Designation LGHB 2/(pack size)
DIN 51825 code KP2N-20 Water resistance
DIN 51 807/1,
NLGI consistency class 2
3 hrs at 90 C 1 max.
Thickener Complex calcium
Oil separation
sulphonate
DIN 51 817,
Colour Brown 7 days at 40 C, static, % 13 at 60 C (140 F)
Base oil type Mineral Lubrication ability
Operating temperature range 20 to +150 C R2F,
(5 to +300 F) running test B at 120 C Pass at 140 C (285 F)
1) Typical value
143
LGHP 2 SKF High Performance, High Temperature Bearing Grease
SKF LGHP 2 is a premium quality mineral oil based grease,
using a modern Polyurea (di-urea) thickener. It is suitable
for electric motors and similar applications.
Typical applications
Electric motors: Small, medium and large
Industrial fans, including high speed fans
Water pumps
Rolling bearings in textile, paper processing and drying machines
Applications with medium and high speed ball (and roller) bearings
operating at medium andhigh temperatures
Clutch release bearings
Vertical shaft applications
Kiln trucks and rollers
Technical data
Designation LGHP 2/(pack size)
DIN 51825 code K2N-40 Water resistance
DIN 51 807/1,
NLGI consistency class 23
3 hrs at 90 C 1 max.
Thickener Diurea
Oil separation
Colour Blue DIN 51 817,
Base oil type Mineral 7 days at 40 C, static, % 15 1)
1) Typical value
144
LGED 2 High temperature & harsh environment bearing grease
SKF LGED 2 is a synthetic fluorinated oil based grease
using a PTFE thickener. It is suitable for extremely high
temperature from 180 C (392 F) up to 240 C (464 F)
and/or agressive environments such as acids/alkalis,
vacuum, oxygen etc.
Typical applications
Bakery/brick oven equipment
Glass industry
Kiln truck wheels
Load rollers in copying machines
Wafer baking equipment Important note:
Textile dryers LGED 2 is a fluorinated grease and is not
Film streching tenders compatible with other greases, oils and
High temperature fans preservatives (except LGET 2). Therefore,
Vacuum pumps very thorough cleaning of bearings and
systems is essential before applying fresh
grease.
Technical data
Designation LGED 2/(pack size)
DIN 51825 code KFK2U-30 EP performance
4ball test,
NLGI consistency class 2
welding load DIN 51350/4, N 8 000 min.
Thickener PTFE
Water resistance
Colour Off white DIN 51 807/1,
Base oil type PFPE 3 hrs at 90 C 1 max.
(Synthetic fluorinated polyether) Copper corrosion
Operating temperature range 30 to +240 C ISO 2160 1 max. at 100 C (210 F)
(22 to +464 F) Rolling bearing grease life
Dropping point DIN ISO 2176 >300 C (>570 F) R0F test
L50 life at 10 000 r/min., hrs >700, at 220 C (430 F)
Base oil viscosity
40 C, mm2/s 460 Evaporation losses
100 C, mm2/s 42 6 weeks at 200 C, % weight losses <3,5%
1) Typical value
145
LGET 2 SKF Extreme Temperature, Extreme Condition Bearing Grease
SKF LGET 2 is a synthetic fluorinated oil based grease,
using a PTFE thickener. It is especially suitable for
applications at extremely high temperatures from
200 C (390 F) up to 260 C (500 F).
Typical applications
Bakery equipment (ovens)
Kiln truck wheels
Load rollers in copying machines
Wafer baking machines Important note:
Textile dryers LGET 2 is a fluorinated grease and is not
Film stretching tenders compatible with other greases, oils and
Electric motors running at extreme temperatures preservatives (except LGED 2). Therefore,
Emergency / hot fans very thorough cleaning of bearings and
Vacuum pumps systems is essential before applying
fresh grease.
Technical data
Designation LGET 2/(pack size)
DIN 51825 code KFK2U-40 Corrosion protection
Emcor:
NLGI consistency class 2
standard ISO 11007 11 max.
Thickener PTFE
Water resistance
Colour Off white DIN 51 807/1,
Base oil type Synthetic 3 hrs at 90 C 0 max.
(fluorinated polyether) Oil separation
Operating temperature range 40 to +260 C DIN 51 817,
(40 to +500 F) 7 days at 40 C, static, % 13 max. 30 hrs at 200 C (390 F)
1) Typical value
146
SKF Food Grade Lubricants
Typical applications
Multi-pack cassette bearings
Wrapping machines
Conveyor bearings
Bottling machines
Ordering details
Pack sizes LGFP 2 Pack sizes LGFP 2
420 ml cartridge LGFP 2/0.4 SKF SYSTEM 24 / LAGD 125 ml LAGD 125/FP2
1 kg can LGFP 2/1 SKF SYSTEM 24 / TLSD 125 ml TLSD 125/FP2
18 kg can LGFP 2/18 SKF SYSTEM 24 / TLSD 250 ml TLSD 250/FP2
180 kg can LGFP 2/180 TLMR 120 ml LGFP 2/MR120
SKF SYSTEM 24 / LAGD 60 ml LAGD 60/FP2 TLMR 380 ml LGFP 2/MR380
Technical data
Designation LGFP 2/(pack size)
NLGI consistency class 2 Corrosion protection
DIN 51825 code K2G-20 Emcor: standard ISO 11007 00 1)
Colour Transparent Water resistance
DIN 51 807/1, 3 hrs at 90 C 1 max.
Soap type Aluminium complex
Oil separation
Base oil type Medical white oil
DIN 51 817, 7 days at 40 C, static, % 15
Operating temperature range 20 to +110 C (5 to +230 F)
Rolling bearing grease life
Dropping point DIN ISO 2176 >250 C (>480 F) R0F test
Base oil viscosity L50 life at 10 000 r/min., hrs 1 000 at 110 C (230 F) 1)
40 C, mm2/s 150 EP performance
100 C, mm2/s 15,3 4ball test,
Penetration DIN ISO 2137 welding load DIN 51350/4, N 1 100 min.
60 strokes, 101 mm 265295 Shelf life 2 years
100 000 strokes, 101 mm +30 max.
NSF Reg. No. 128004
1) Typical value
147
LGFQ 2 High load, water resistant and wide temperature food grade grease
SKF LGFQ 2 is a synthetic oil based grease using the latest
complex calcium sulphonate thickener technology. It is
suitable for applications subjected to high loads, wet
environment and fluctuating temperatures encountered in
the food and beverage industry.
Typical applications
Pellet presses (pet food, sugar, salt)
Mixers
Mills
Centralized lubrication systems
Technical data
Designation LGFQ 2/(pack size)
DIN 51825 KP1/2N-40 Water resistance
Thickener Complex calcium sulphonate DIN 51807/1, 3 hrs at 90 C 1 max.
Water wash out ASTM D1264, % 0
NLGI grade 12
Oil separation
Colour Brown DIN 51817, 7 days at 40 C, % 3 max.
Base oil type Synthetic (PAO) Lubrication ability
Operating temperature range 40 to +140 C R2F, running test B at 120 C Pass
(40 to +284 F) Copper corrosion
Dropping point, DIN ISO 2176 >300 C (>570 F) DIN 51811 1b max. at 100 C (210 F)
Base oil viscosity EP performances
40 C, mm2/s 320 DIN 51350/5, wear scar, 1 400 N, mm 1 max.
100 C, mm2/s 30 DIN 51350/4, weld load, N >4 000
Penetration DIN ISO 2137 Fretting corrosion
60 strokes 280310 ASTM D4170 FAFNIR test, mm 0,8 1)
100 000 strokes +30 max. Shelf life 2 years
Mechanical stability NSF Reg. No. 153759
Roll stability, 50h at 80 C, 10-1 mm 20 to +30 max.
Available pack sizes 420 ml cartridges,
Corrosion protection 18, 50, 180 kg,
Emcor: standard ISO 11007 00 SKF SYSTEM 24
salt water test (0.5% NaCl) LAGD, TLSD, TLMR
DIN 51802 00
1) Typical value
148
LFFH 46 Food grade hydraulic oil
SKF LFFH 46 and LFFH 68 are synthetic hydraulic
fluids suitable for lubrication of machinery used in
LFFH 68 the food industry.
Typical applications
Hydraulic systems
Hydrostatic gears
Circulating oil systems
Ordering details
Pack sizes LFFH 46 LFFH 68
22 l can LFFH 46/22 LFFH 68/22
205 l can LFFH 46/205 LFFH 68/205
Technical data
Designation LFFH 46/(pack size) LFFH 68/(pack size)
Appearance Yellowish Yellowish
Operating temperature range 60 to +140 C (76 to +284 F) 50 to +140 C (58 to +284 F)
Base oil type Synthetic (PAO) Synthetic (PAO)
Base oil viscosity ISO 3104
40 C, mm2/s 46 68
100 C, mm2/s 7,9 10,6
Density ISO 12185
15 C, kg/m3 836 843
Flash point DIN/EN/ISO 2592 COC 248 C 258 C
Pourpoint ISO 3016 <60 C <60 C
FZG-Test A/8.3/90 Failure Load Stage DIN 51354-2 12 >12
Viscosity Index DIN ISO 2909 142 143
Shelf life 2 years 2 years
NSF Reg. No. 149599 149600
149
LFFG 220 Food grade gear oil
SKF LFFG 220 and LFFG 320 are synthetic gear
oils suitable for lubrication of machinery used in
LFFG 320 the food industry.
Excellent EP properties
High viscosity index resulting in minimum variation of viscosity
with change of temperature
Excellent protection against corrosion
NSF H1 registered and Halal and Kosher certified
Typical applications
Enclosed gear boxes
Packaging
Conveyers
Ordering details
Pack sizes LFFG 220 LFFG 320
22 l can LFFG 220/22 LFFG 320/22
205 l can LFFG 220/205 LFFG 320/205
Technical data
Designation LFFG 220/(pack size) LFFG 320/(pack size)
Appearance Pale yellow Pale yellow
Operating temperature range 40 to +140 C (40 to +284 F) 35 to +140 C (31 to +284 F)
Base oil type Synthetic (PAO) Synthetic (PAO)
Base oil viscosity ISO 3104
40 C, mm2/s 220 320
100 C, mm2/s 25 33,4
Density ISO 12185
15 C, kg/m3 847 852
Flash point DIN/EN/ISO 2592 COC 276 C (529 F) 278 C (532 F)
Pourpoint ISO 3016 48 C (54 F) 45 C (49 F)
FZG-Test A/8.3/90 Failure Load Stage DIN 51354-2 >12 >12
Viscosity Index DIN ISO 2909 143 147
Shelf life 2 years 2 years
NSF Reg. No. 149597 149598
150
LFFM 80 Food grade chain oil
Our food grade chain oil range is specifically developed for
food and beverage applications where high temperature, high
LHFP 150 humidity and low temperatures are critical factors to consider
in the selection of the correct oil.
LHFP 150 General purpose chain oil LHFP 150 excels in low to elevated
temperature applications such as in confectionery industries and fruit and
vegetable processing. The formulation is based on a synthetic oil and the
product provides good corrosion and wear protection together with good
aging and oxidation stability.
LFFT 220 High temperature performance chain oil LFFT 220 is mainly
for use in bakery ovens or other equipment subjected to high temperatures.
It provides good wear protection and low evaporation losses at elevated
temperatures along with excellent oxidation resistance due to its
formulation and synthetic base.
Ordering details
Pack sizes LFFM 80 LHFP 150 LFFT 220
5 l can LFFM 80/5 LHFP 150/5 LFFT 220/5
SKF SYSTEM 24 / LAGD 125 ml LAGD 125/FFM80 LAGD 125/HFP15 LAGD 125/FFT22
SKF SYSTEM 24 / TLSD 122 ml LHFP 150/SD125
SKF SYSTEM 24 / TLSD 250 ml LHFP 150/SD250
Technical data
Designation LFFM 80 LHFP 150 LFFT 220
Appearance White Colourless Yellow
Base oil type Semi synthetic (mineral/ester) Synthetic (PAO)/Ester Synthetic (Ester)
Specific gravity 0,89 0,85 0,95
Operating temperature range 30 to +120 C (22 to +248 F) 30 to +120 C (22 to +248 F) 0 to 250 C (32 to 482 F)
Base oil viscosity:
40 C, mm2/s approx. 80 ISO VG 150 ISO VG 220
100 C, mm2/s approx. 10 approx. 19 approx. 17
Flash point >200 C (>392 F) >200 C (>392 F) >250 C (>482 F)
NSF Reg. No. 146767 136858 146768
Shelf life 2 years 2 years 2 years
151
LDTS 1 Food grade dry film lubricant
SKF Dry Film Lubricant LDTS 1 has been specially
developed for automatic lubrication of plastic flat top
chain conveyors in the beverage processing industry.
The lubricant consists of synthetic oil and is doped with
PTFE solid lubricant.
Typical applications
Conveyors in bottling lines using PET, carton, glass or can packages.
Ordering details
Pack sizes LDTS 1
5 l can LDTS 1/5
Technical data
Designation LDTS 1
Composition Mineral oils, hydrocarbons, Flash point of the preparation ca. 100 C (210 F)
additives, PTFE Flash point after evaporation
Appearance White of the solvent >170 C (340 F)
Operating temperature range 5 to +60 C (25 to 140 F) NSF Reg. No. 139739
Viscosity at 40 C (104 F) ca. 28 mm2/s Shelf life 2 years
Pour point <0 C
Density 25 C (77 F) ca. 841 kg/m3
152
LMCG 1 Grid and gear coupling grease
LMCG 1 is a polyethylene thickened and mineral oil based grease which also
uses a lithium complex thickening technology. The grease is formulated to
withstand high centrifugal forces and high-torque applications for grid and
gear (flexible) couplings even where severe shock loadings, misalignment
and vibration occur.
Technical data
Designation LMCG 1/(pack size) LGLS 0/(pack size)
DIN 51825 code GOG1G-0 KP0G-40
NLGI consistency class 1 0
Thickener Polyethylene Anhydrous calcium
Colour Brown Red
Base oil type Mineral Mineral oil & polymers
Operating temperature range 0 to 120 C (32 to 248 F) 40 to +100 C (40 to +212 F)
Dropping point IP 396 210 C (410 F) >120 C (>248 F)
Base oil viscosity
40 C, mm2/s 761 1 370
100 C, mm2/s 44 96
Penetration DIN ISO 2137
60 strokes, 101 mm 310340 355385
Corrosion protection
SKF Emcor standard ISO 11007 00 0-0
Flow pressure at 40 C <1 400 mbar
EP performance
Wear scar DIN 51350/5, 1 400 N, mm 0,5 max.
4ball test, welding load DIN 51350/4 3 200 N 1) 3 200 N
Available pack sizes 35 g tube, 420 ml cartridge, 2, 18, 50 kg 18 kg, 180 kg
1) Typical value
153
LHMT 68 SKF Chain Oil
LHHT 265 - SKF LHHT 265 synthetic oil is ideal for high load and/or
high temperature conditions, like those found in the pulp and paper and
textile industries. It doesnt form any residue at high temperatures and
it is neutral towards seals and polymers.
Typical applications
Conveyor chains
Drive chains
Lift chains
Ordering details
Chain oil LHMT 68 LHHT 265
Description Medium temperature oil High temperature oil
Can 5 liter LHMT 68/5 LHHT 265/5
SKF SYSTEM 24
LAGD series Unit 60 ml LAGD 60/HMT68 1)
Unit 125 ml LAGD 125/HMT68 1) LAGD 125/HHT26 1)
TLSD series Complete unit 122 ml TLSD 125/HMT68 TLSD 125/HHT26
Complete unit 250 ml TLSD 250/HMT68 TLSD 250/HHT26
Refill set 122 ml LHMT 68/SD125 LHHT 265/SD125
Refill set 250 ml LHMT 68/SD250 LHHT 265/SD250
1) Includes non-return valve
Technical data
Designation LHMT 68 LHHT 265
Description Medium temperature oil High temperature oil
Specific gravity 0,85 0,92
Colour Yellowish brown Yellow orange
Base oil type Mineral Synthetic (PAO)/Ester
Operating temperature range 15 to +90 C (5 to 194 F) Up to 250 C (482 F)
Base oil viscosity:
40 C, mm2/s ISO VG 68 approx. 265
100 C, mm2/s approx. 9 approx. 30
Flash point >200 C (392 F) approx. 260 C (500 F)
Pour point <-15 C (5 F) n/a
154
Technical data
Understanding grease technical data
Some basic knowledge is required to understand the technical data so that you
can select the proper grease. This is an excerpt of the main terms mentioned in
SKF grease technical data.
Consistency Viscosity
A measure of the stiffness of a grease. A proper consistency must A measure of a fluids resistance to flow. For lubricants, a proper viscosity
ensure that the grease stays in the bearing without generating too must guarantee an adequate separation between surfaces without
much friction. It is classified according to a scale developed by the NLGI causing too much friction. According to ISO standards, it is measured at
(National Lubricating Grease Institute). The softer the grease, the lower 40 C (105 F), as viscosity changes with temperature. Values at 100 C
the number. Grease for bearings are typically NLGI 1, 2 or 3. The test (210 F) allow calculation of the viscosity index, e.g. how much the
measures how deep a cone falls into a grease sample in tenths of mm. viscosity will decrease when temperature rises.
Mechanical stability
The consistency of bearing greases should not significantly change
Classification of greases by NLGI consistency number during its working life. Three main tests are normally used to analyse
NLGI ASTM worked Appearance this behaviour:
number penetration at room
(101 mm) temperature Prolonged penetration
000 445475 very fluid
The grease sample is subjected to 100 000 strokes in a device
called a grease worker. Then, the penetration is measured.
00 400430 fluid
The difference against penetration at 60 strokes is reported
0 355385 semi-fluid
as the change in 101 mm.
1 310340 very soft
Roll stability
2 265295 soft
A grease sample is placed in a cylinder with a roller inside. The
3 220250 medium hard cylinder is then rotated for 72 or 100 hours at 80 or 100 C
4 175205 hard (175 or 210 F) (the standard test demands just 2 hours at room
5 130160 very hard temperature). At the end of the test period, once the cylinder has
6 85115 extremely hard cooled to room temperature, the penetration of the grease is
measured and the change in consistency is reported in 101 mm.
V2F test
Temperature range A railway axlebox is subjected to vibration shocks of 1 Hz from a
Comprehends the suitable working range of the grease. It goes between bouncing hammer producing an acceleration level between 1215 g.
the low temperature limit (LTL) and the high temperature performance After 72 hours at 500 r/min., the grease leaked from the housing
limit (HTPL). LTL is defined as the lowest temperature at which the through the labyrinth seal is collected in a tray. If it weighs less than
grease will allow the bearing to be started up without difficulty. 50 g, a rating of m is granted, otherwise it is rated as fail. Afterwards,
Below this limit, starvation will occur and cause a failure. Above HTPL, the test is continued for another 72 hours at 1 000 r/min. If less than
the grease will degrade in an uncontrolled way so that grease life cannot 150 grams of grease leaked after completion of both tests, then a
be determined accurately. rating of M is given.
155
Lubrication ability
Water resistance The R2F test assesses the high temperature performance and lubricating
A glass strip is coated with the candidate grease, which is placed into ability of a grease. A shaft with two spherical roller bearings in their
a water-filled test tube. The test tube is immersed in a water bath respective housings is driven by an electric motor. The bearings are run
for three hours at a specified test temperature. The change in the under load, the speed may be varied and heat can be applied. The test
grease is visually evaluated and reported as a value between 0 method is carried out under two different conditions after which the wear
(no change) and 3 (major change) along with the test temperature. of the rollers and the cage is measured. Test A is conducted at ambient
temperature and a pass rating means that the grease can be used to
lubricate large bearings at normal operating temperatures and also in
low vibrating applications. Test B runs at 120 C (250 F) and a pass
Water resistance test rating indicates suitability for large bearings at high temperatures.
Copper corrosion
Lubricating greases should protect copper alloys used in bearings from
corrosive attack while in service. To assess these properties, a copper
Glass or metal plate
strip is immersed in the grease sample and placed in an oven. The strip
is then cleaned and the degradation is observed. The result is rated by
Thin layer of grease on plate
anumerical system and a rating above 2 indicates poor protection.
Distilled water
Rolling bearing grease life
Temperature controlled bath, The R0F and ROF+ tests determine the grease life and its high
e.g. 90 1 C temperature performance limit (HTPL). Ten deep groove ball bearings
are fitted into five housings and filled with a given quantity of grease.
The test is undertaken at a pre-determined speed and temperature.
Axial and radial loads are applied and the bearings run to failure.
The time to failure is recorded in hours and a Weibull life calculation
is made to establish the grease life. This information can then be used
to determine re-lubrication intervals in an application.
Oil separation
Lubricating greases release oil when stored for long periods of time Extreme pressure (EP) performance
or when used in bearings as a function of temperature. The degree The 4-ball weld load test rig uses three steel balls held in a cup. A fourth
of oil separation will depend upon the thickener, base oil and ball is rotated against the three balls at a given speed. A starting load is
manufacturing method. In the test, a cup is filled with a given applied and increased at pre-determined intervals until the rotating ball
quantity of grease (and is weighed before the test) and a 100 gram seizes and welds to the stationary balls. Values above 2 600 N are
weight is placed on top of the grease. The complete unit is placed typically expected in EP grease. Under the 4-ball wear scar test, SKF
into an oven at 40 C (105 F) for one week. At the end of the week, applies 1 400 N (standard test uses 400 N) on the fourth ball during
the amount of oil which has leaked through the sieve, is weighed and 1minute. The wear on the three balls is measured and values below
reported as a percentage of weight loss. 2mm are considered as appropriate values for EP greases.
Fretting corrosion
Oil separation test Vibrating or oscillating conditions are typical causes for fretting corrosion.
Under the FAFNIR test, two thrust ball bearings are loaded and subjected
to oscillation. The wear on each bearing is then measured. A wear below
7mg indicates good fretting protection.
Dead weight
(gives light pressure
on grease sample)
P
Sieve
Separated oil
156
Thickener compatibility chart
Lithium Calcium Sodium Lithium Calcium Sodium Barium Aluminium Clay Common Calcium
complex complex complex complex complex (Bentonite) polyurea 1) sulphonate
complex
Lithium + - + - - +
Calcium + + - - +
Sodium - + + + - -
Lithium
complex + + + + + - - +
Calcium
complex - - + + - + +
Sodium
complex + + + - -
Barium
complex + - + + +
Aluminium
complex - - - + - + + - -
Clay
(Bentonite) - - - + -
Common
polyurea 1) - + + +
Calcium
sulphonate
complex
+ + - + + - - + +
Mineral/
PAO + + - - + -
Ester + + + - + -
Polyglycol - + + - - - -
Silicone:
Methyl - - - + + - -
Silicone:
Phenyl + + - + + + -
Polyphenyl-
ether - - + + -
PFPE - - - - - - +
+ = Compatible 1) SKF high performance, high temperature bearing grease LGHP2 is not a common polyurea type grease. It is a di-urea bearing grease,
= Test required which has successfully been tested for compatibility with lithium and lithium complex thickened greases i.e. LGHP 2 is compatible with
- = Incompatible such greases.
157
Automatic grease dispensing tools
Manual lubrication vs. automatic lubrication
Performing manual lubrication tasks can be challenging due to the vast number of lubrication points
throughout a factory. Also, most of these points have varying lubrication requirements. Utilising
automatic lubricators is one solution that can improve worker safety and increase machine reliability.
Optimal lubrication
Manual lubrication
158
Improving employee safety
Use of SKF SYSTEM 24 lubricators can have a positive impact on workplace safety
because technicians can spend less time in confined spaces, with safety cages or guards
removed, and on rooftop or elevated lubrication tasks.
159
Machine reliability
The importance of lubrication often is overlooked due to its underestimated impact on equipment
total cost of ownership. However, machine reliability can be enhanced substantially with proper
lubrication. As the leading supplier of bearings worldwide, SKF has conducted extensive research
and determined that up to 50 percent of premature bearing failures are due to either improper
lubrication practices or contamination.
Contamination 14%
Positive pressure
Positive pressure prevents contaminants
from entering the bearing through the seal.
SKF SYSTEM 24 lubricators can provide fresh
lubricant and purge seals of smaller-sized
bearings operating at lower speeds, while larger
bearings may benefit from a separate lubricator
for lubrication and seal purging.
160
Supporting effective maintenance
The use of automatic lubricators can have a large impact on effective maintenance.
The most significant benefits usually are found in the reduction of unplanned downtime,
machine repair costs, labor and lubricant consumption.
Manual Automatic
Increased productivity
Because automatic lubricators deliver lubricant
while the equipment is in operation, there is less
scheduled downtime and more productivity.
161
SKF SYSTEM 24
Gas driven single point automatic lubricators
SKF LAGD series
The units are supplied ready-to-use straight from the box and filled with a wide
range of high performance SKF lubricants. Tool-free activation and time-setting
allow easy and accurate adjustment of lubrication flow.
Typical applications
Applications in restrictive and hazardous locations
Bearing housing lubrication
Electric motors
Fans and pumps
Conveyors
Cranes
Chains (oil)
Elevators and escalators (oil)
162
60 ml unit
Ordering details
Grease LGWA 2 LGEM 2 LGGB 2 LGHB 2 LGHP 2 LGFP 2 LGWM 2 LGFQ 2
Description High load, High viscosity Biodegradable High load, High performance, Food compatible High loads, wide High load and wide
extreme pressure, bearing grease with high temperature, high temperature NSF H1 certified temperature temperature food
wide temperature solid lubricants high viscosity grade
range
Unit 60 ml LAGD 60/WA2 LAGD 60/EM2 LAGD 60/HB2 LAGD 60/HP2 LAGD 60/FP2
Unit 125 ml LAGD 125/WA2 LAGD 125/EM2 LAGD 125/GB2 LAGD 125/HB2 LAGD 125/HP2 LAGD 125/FP2 LAGD 125/WM2 LAGD 125/FQ2
Chain oils LHMT 68 LHHT 265 LFFM 80 LHFP 150 LFFT 220
Description Medium High Food grade Food grade Food grade Empty unit suitable for
temperature oil temperature oil (NSF H1) oil (NSF H1) oil (NSF H1) oil oil filling only
Technical data
Designation LAGD 60 and LAGD 125
Grease capacity Intrinsically safe approval II 1 G Ex ia IIC T6 Ga
LAGD 60 60 ml (2 US fl. oz) II 1 D Ex ia IIIC T85C Da
LAGD 125 125 ml (4.2 US fl. oz) I M1 Ex ia I Ma
Nominal emptying time Adjustable; 112 months EC Type examination certificate Kema 07ATEX0132 X
Ambient temperature range Protection class IP 68
LAGD 60/.. and LAGD 125/.. 20 to +60 C (5 to +140 F) Recommended storage temperature 20 C (70 F)
Maximum operating pressure 5 bar (75 psi) (at start-up) Storage life of lubricator 2 years
Drive mechanism Gas cell producing inert gas Weight
Connection thread R 1/4 LAGD 60 approx 200 g (7.1 oz)
LAGD 125 approx 130 g (4.6 oz)
Maximum feed line length with:
Lubricant included
grease 300 mm (11.8 in.)
oil 1 500 mm (59.1 in.)
Note: If ambient temperature is constant between 40 C and 60 C (105 F and 140 F), do not select a setting of more than 6 months for optimum performance.
LGHP 2 should not be used with ambient temperatures over 40 C (105 F) or have a time setting longer than 6 months.
163
SKF SYSTEM 24
Electro-mechanical single point automatic lubricators
SKF TLSD series
The SKF TLSD series is the first choice when a simple and reliable automatic
lubricator is required under variable temperatures, or when the application
conditions (such as vibration, limited space or hazardous environments)
require a remote mounting.
Typical applications
Critical applications where extreme reliability and additional
monitoring is required
Applications in restrictive and hazardous locations
Applications requiring high volumes of lubricant
n
A The unit can be programmed to dispense lubricant in
1, 2, 3, 4, 6, 8, 9, 10 and 12 month settings.
n
B The same drive unit can be used with both cartridge versions
by simply adjusting the 125/250 ml switch.
n
C Traffic light LEDs are visual from all sides because of the presence of
dual LEDs on the sides of the lubricator. The meaning of the lights
C A
is as follows:
Green light: The lubricator is properly functioning.
Yellow light: The lubricator is still functioning, but soon some
action will be required. Yellow light serves as a
pre-warning light.
Red light: The lubricator stopped operating.
B
164
Ordering details 1)
Grease LGWA 2 LGEM 2 LGHB 2 LGHP 2 LGFP 2 LGWM 2 LGFQ 2
Description High load, extreme High viscosity High load, High performance, Food compatible High loads, High load and
pressure, wide bearing grease with high temperature, high temperature NSF H1 certified wide temperature wide temperature
temperature range solid lubricants high viscosity food grade
Complete unit 125 TLSD 125/WA2 TLSD 125/EM2 TLSD 125/HB2 TLSD 125/HP2 TLSD 125/FP2
Complete unit 250 TLSD 250/WA2 TLSD 250/EM2 TLSD 250/HB2 TLSD 250/HP2 TLSD 250/FP2
Refill set 125 LGWA 2/SD125 LGEM 2/SD125 LGHB 2/SD125 LGHP 2/SD125 LGFP 2/SD125 LGWM 2/SD125 LGFQ 2/SD125
Refill set 250 LGWA 2/SD250 LGEM 2/SD250 LGHB 2/SD250 LGHP 2/SD250 LGFP 2/SD250 LGWM 2/SD250 LGFQ 2/SD250
Technical data
Designation TLSD 125 and TLSD 250
Grease capacity LED status indicators
TLSD 125 125 ml (4.2 US fl. oz) Green led (each 30 sec) OK
TLSD 250 250 ml (8.5 US fl. oz) Yellow led (each 30 sec) Pre warning, low battery power
Yellow led (each 5 sec) Pre warning, high back pressure
Emptying time User adjustable: 1, 2, 3, 4, 6, 8, 9, 10 and
Red led (each 5 sec) Warning, stopped on error
12 months
Red led (each 2 sec) Warning, empty cartridge
Lowest grease purge
Protection class assembled
TLSD 125 0,3 ml (0.01 US fl. oz) per day
lubricator IP 65
TLSD 250 0,7 ml (0.02 US fl. oz) per day
Battery pack
Highest grease purge
TLSD 1-BAT 4,5 V 2,7 Ah/Alkaline manganese
TLSD 125 4,1 ml (0.13 US fl. oz) per day
TLSD 1-BATC 4,5 V 2,9 Ah/Lithium-Iron Disulfide
TLSD 250 8,3 ml (0.28 US fl. oz) per day
Recommended storage
Ambient temperature range
temperature 20 C (70 F)
TLSD 1-BAT 0 to 50 C (30 to 120 F)
TLSD 1-BATC 10 to +50 C (15 to 120 F) Storage life of lubricator 3 years 3)
(2 years for LGFP 2 and Oils)
Maximum operating pressure
5 bar (75 psi) Total weight (incl. packaging)
TLSD 125 635 g (22.5 oz)
Drive mechanism Electro mechanical
TLSD 250 800 g (28.2 oz)
Connection thread G 1/4
Maximum feed line length with:
grease Up to 3 meters (10 ft) 2)
oil Up to 5 meters (16 ft)
1) TLSD lubricator and SD refill sets are not for offer/sale/use in Germany, France or United States until December 2017.
2) The maximum feed line length is dependent on ambient temperature, grease type and back pressure created by the application.
3) Maximum storage life is 3 years from production date, which is printed on the side of the canister. The canister and battery pack
may be used at 12 month setting even if activated 3 years from production date.
165
Electro-mechanical single point automatic lubricators
SKF TLMR series
The SKF Automatic Lubricant Dispenser TLMR is a single point automatic
lubricator designed to supply grease to a single lubrication point. With a relatively
high pressure of 30 bars, this lubricator can operate at long distances providing
optimum results with difficult-to-reach and unsafe lubrication locations. With a
wide temperature range and robust design, the TLMR lubricator is suitable for
operating conditions with various levels of temperature and vibration.
Typical applications
Applications requiring high lubricant consumption
Applications experiencing high vibration in operation
Excellent water and dust protection makes TLMR suitable for general
machinery applications and food processing machinery
Excellent high temperature performance makes TLMR suitable for engine
rooms and hot fan applications
Excellent low temperature performance makes TLMR suitable for
wind turbine applications
Each TLMR is supplied with a strong mounting bracket as For ease of use, cartridges are easily exchanged by simply
standard. The bracket enables the TLMR to be easily mounted screwing them into the lubricator.
on a flat surface.
166
Ordering details
Grease Description TLMR 101 refill sets (cartridge and battery) TLMR 201 cartridges
120 ml 380 ml 120 ml 380 ml
LGWA 2 High load, extreme pressure, wide LGWA 2/MR120B LGWA 2/MR380B LGWA 2/MR120 LGWA 2/MR380
temperature range bearing grease
LGEV 2 Extremely high viscosity bearing grease LGEV 2/MR380B LGEV 2/MR380
with solid lubricants
LGHB 2 High load, high temperature, LGHB 2/MR380B LGHB 2/MR380
high viscosity bearing grease
LGHP 2 High performance,high temperature LGHP 2/MR380B LGHP 2/MR380
bearing grease
LGFP 2 Food grade bearing grease LGFP 2/MR120B LGFP 2/MR380B LGFP 2/MR120 LGFP 2/MR380
NSF H1 certified
LGWM 1 Extreme pressure, low temperature LGWM 1/MR380B LGWM 1/MR380
bearing grease
LGWM 2 High load, wide temperature range LGWM 2/MR380B LGWM 2/MR380
bearing grease
LGEP 2 Extreme pressure bearing grease LGEP 2/MR380B LGEP 2/MR380
LGMT 3 All purpose industrial and LGMT 3/MR380B LGMT 3/MR380
automotive bearinggrease
LGGB 2 Biodegradable bearing grease LGGB 2/MR380B LGGB 2/MR380
LGFQ 2 High load and wide temperature LGFQ 2/MR380B LGFQ 2/MR380
food grade bearing grease
Technical data
Designation TLMR 101 and TLMR 201
Grease capacity 120 ml (4.1 US fl. oz) Connection thread G 1/4 female
380 ml (12.8 US fl. oz) Maximum feed line length 1) Up to 5 meters (16 ft)
Emptying time User adjustable: 1,2,3,6,9,12, 18, LED status indicators
24 months or purge Green LED (every 8 sec) OK
Lowest setting Green and red LED (every 8 sec) Almost empty
120 ml cartridge 0,16 ml (0.005 US fl. oz) per day Red LED (every 8 sec) Error
380 ml cartridge 0,5 ml (0.016 US fl. oz) per day Protection class
Highest setting DIN EN 60529 IP 67
120 ml cartridge 3,9 ml (0.13 US fl. oz) per day DIN 40 050 Teil 9 IP 6k9k
380 ml cartridge 12,5 ml (0.42 US fl. oz) per day Power
Purge 31 ml (1 US fl. oz) per hour TLMR 101 4 AA Lithium batteries
TLMR 201 1224 Volt DC
Ambient temperature range 25 to +70 C (13 to +158 F)
Maximum operating pressure 30 bar (435 psi)
Drive mechanism Electro mechanical
1) The maximum feed line length is dependent on ambient temperature, grease type and back pressure created by the application.
167
Ready-to-use centralised lubrication system
SKF MultiPoint Automatic Lubricators TLMP series
The SKF MultiPoint Automatic Lubricator TLMP series is intended for reliable relubrication of
multiple lubrication points. This sturdy automatic lubrication system is packaged as a complete
kit, including the lubricator, required tubing and connectors. Designed to supply from one to
eighteen lubrication points, the TLMP series features pluggable outlets and is easy to install
and program via its keypad with LED display.
The TLMP series are supplied complete with the following items
LAGF 1-H
168
Filter to avoid grease
contamination from
airborne particles
Technical data
Designation TLMP 1008 and TLMP 1018
Number of lubrication outlets External steering By disconnecting power supply
TLMP 1008 18
Ambient temperature 25 to +70 C (13 to +160 F)
TLMP 1018 118
IP rating IP 67
Suitable grease consistency NLGI 2, 3
Lubrication tubes
Maximum pressure 120 bar (1 740 psi)
TLMP 1008 20 m (65 ft), 6 1,5 mm, Nylon
Maximum distance length to 5 m (16 ft) TLMP 1018 50 m (164 ft), 6 1,5 mm, Nylon
lubrication point
Weight Approx. 6 kg (13 lb)
Dispense rate 0,1 - 40 cm3/day
Ordering details 8 oulets
(0.003 -1.35 US fl.oz/day) per outlet
TLMP 1008/24DC 24 V DC (20/+30%)
Output pump element Approx. 0,2 cm3 (per cycle), TLMP 1008/120V 120 V AC 60 Hz (10%)
approx. 1,7 cm3 (per minute) TLMP 1008/230V 230 V AC 50 Hz (10%)
Reservoir size 1 litre Ordering details 18 oulets
TLMP 1018/24DC 24 V DC (20/+30%)
Useable reservoir volume Approx. 0,50,9 litres (1730 US fl.oz)
TLMP 1018/120V 120 V AC 60 Hz (10%)
Filling Via hydraulic lubrication fitting R1/4 TLMP 1018/230V 230 V AC 50 Hz (10%)
Installation position Vertical (max deviation 5)
Power Supply Connector EN 175301-803 DIN 43650/A
Alarms blocked feed lines, empty reservoir
internal and external
169
Accessories
A full range for enhanced versatility of SKF automatic lubricators
Connectors Connectors
G 1 /8
LAPA 45 Angle connection 45 LAPN 1/8 Nipple G 1/4 G 1/8
G 1/4
G 1 /4
LAPA 90 Angle connection 90 LAPN 1/4 Nipple G 1/4 G 1/4
G 1/4
G 1 /2
LAPE 35 Extension 35 mm LAPN 1/2 Nipple G 1/4 G 1/2
G 1/4
1/4"28 UNF
G 1/4
G 1/4 G 3 /8
LAPF F 1/4 Tube connection female LAPN 3/8 Nipple G 1/4 G 3/8
G 1/4
8 mm G 1/4
6 mm M6
LAPF M 1/8 S Tube connection male LAPN 6 Nipple G 1/4 M6
G 1/8 for 6 4 tube
G 1/8
G 1/4
6 mm M8
LA PF M 1/4 S Tube connection male LAPN 8 Nipple G 1/4 M8
G 1/4 for 6 4 tube
G 1/4
G 1/4
8 mm M81
LAPF M 1/8 Tube connection male LAPN 8x1 Nipple G 1/4 M8 1
G 1/8
G 1/8
G 1/4
8 mm M10
LAPF M 1/4 Tube connection male LAPN 10 Nipple G 1/4 M10
G 1/4
G 1/4 G 1/4
8 mm M101
LAPF M 1/4SW Extra strong tube LAPN 10x1 Nipple G 1/4 M10 1
connection male G 1/4
G 1/4 G 1/4
8 mm M12
LAPF M 3/8 Tube connection male LAPN 12 Nipple G 1/4 M12
G 3/8
G 3 /8
G 1/4
DIN 71412 M121,5
LAPG 1/4 Grease nipple G 1/4 LAPN 12x1.5 Nipple G 1/4 M12 1,5
R 1/4
G 1/4
LAPM 2 Y-connection
SKF LAGD Series
170
Non return valves (for oil applications) Mounting and protecting devices and extras
G 1/4 7 mm 45 mm
LAPV 1/4 Non-return valve G 1/4 LAPC 13 Bracket
G 1/4 13,6 mm
G 1/4 50 mm
LAPV 1/8 Non-return valve G 1/8 LAPC 50 Clamp
G 1/8
63 mm
LAPC 63 Clamp
100 mm 30 mm
1 000 mm long, 8 6 mm
6 mm
G 1/4
LAPB 5-16E1 Elevator brush, 8 mm
516 mm gap LAPT 5000 Flexible tube,
5 000 mm long, 8 6 mm
6 mm
6 mm
LAPT 1000S Extra strong flexible tube,
1 000 mm long, 6 4 mm
4 mm
6 mm
LAPT 5000S Extra strong flexible tube,
5 000 mm long, 6 4 mm
4 mm
8 mm
LAPT 1000SW Extra strong flexible tube,
1 000 mm long, 8 6 mm
6 mm
8 mm
LAPT 5000SW Extra strong flexible tube,
5 000 mm long, 8 6 mm
6 mm
171
Manual grease dispensing tools
A basic element of lubrication plans
The main pitfall of manual lubrication is ensuring accuracy and top cleanliness.
Lubricant film in the application can be over 40 times thinner than the smallest
visible particle. The SKF range of manual lubrication tools is designed to help
you with the storage, handling, dosing and supplying of lubricants for your
machinery in a clean and easy way.
Supplied with three spout caps For use with cartridges and loose grease
Applies grease to open applications such as bearings or open gears Knurled body for firm and safe grip
High quality steel is dent-resistant for easy cartridge loading
Special piston design for smooth emptying of cartridges
Volume/stroke
TLGH 1: 0,9 cm3 (0.055 in.3)
1077600: 1,5 cm3 (0.092 in.3)
172
Selection chart and technical data SKF Grease Guns
Designation LAGP 400 TLGH 1 1077600 1077600/SET LAGH 400
Volume per stroke 20 cm3 (1.2 in. 3) Approx. Approx. Approx. Approx.
0,9 cm3 (0.05 in. 3) 1,5 cm3 (0.09 in. 3) 1,5 cm3 (0.09 in.3) 0,8 cm3 (0.05 in. 3)
Weight 0,35 kg 1,5 kg 1,5 kg Complete: 2,4 kg 1,2 kg
(12 oz) (3.3 lb) (3.3 lb) (5.3 lb) (2.6 lb)
Reservoir Suitable for the Loose grease Loose grease Loose grease Loose grease
SKF grease cartridges. (ca. 500 cm3) or (ca. 500 cm3) or (ca. 500 cm3) or (ca. 500 cm3) or
grease cartridges. grease cartridges. grease cartridges. grease cartridges.
Discharge pipe 175 mm (6.9 in.) 175 mm (6.9 in.) 175 mm (6.9 in.) 300 mm (12 in.)
length
Accessories 1077601 1077601 1077601 1077601
Note: 1077601: Flexible 500 mm (19.7 in.) long pressure hose with hydraulic gripping nozzle.
173
Technology and reliability in a durable design
SKF Battery Driven Grease Gun TLGB 20
Developed to maximize efficiency, the SKF Battery Driven Grease Gun TLGB 20 includes an
integrated grease meter to help prevent over- and under-lubrication. This unique tool features
a durable, ergonomic design with a three-point stand for operator comfort and convenience and
a 20-volt, lithium-ion battery for longer life. Suitable for a variety of manual lubrication tasks,
the TLGB 20 can be used to lubricate bearings and machines in industrial and manufacturing
environments, as well as agricultural and construction vehicles.
174
LED light Filler nipple Spring guards
Illuminates work area to Facilitates clean and Preserves flex hose life
help locate grease fittings simple filling from by preventing kinks
in dimly lit environments drums using filler
pumps Vent valve
Removes trapped air inside grease
gun for trouble-free priming
Multi-function LCD
Display shows grease output and
battery charge and alerts the
operator of blocked fittings and
loss of prime
Ergonomic design
Lightweight with optimized
balance for operator comfort
20 V Lithium-ion battery
Dispenses up to 15 grease
cartridges per charge and
maintains stable energy output
4-Jaw coupler
Precision machined for durability
Technical data
Designation TLGB 20 and TLGB 20/110V
Display Grease meter Battery type Li-Ion
Battery capacity gauge Battery output 20V DC maximum (without workload)
Alert of blocked fittings
Alert of loss of prime Battery capacity 1 500 mAh
Grease output Voltage charger, V/Hz
Low speed setting 100 ml/min. (3.5 oz/min.) at 70 bar pressure TLGB 20 200240 V/5060 Hz
High speed setting 160 ml/min. (5.5 oz/min.) at 70 bar pressure TLGB 20/110V 110120 V/60 Hz
Maximum operating Carrying case dimensions 590 110 370 mm (23.2 4.3 14.5 in.)
pressure 400 bar (6 000 psi) Weight 3,0 kg (6.5 lb)
Maximum peak pressure 700 bar (10 000 psi) Total weight (incl.case) 5,7 kg (12.7 lb)
Cartridges per Accessories
battery charge 15 cartridges TLGB 20-1 Carrying strap
Length of hose 900 mm (36 in.) TLGB 20-2 20 V Li-Ion battery
175
Optimum cleanliness when filling your grease guns
SKF Grease Filler Pumps LAGF series
Best lubrication practices say that each type of grease requires an individual
grease gun and the refilling has to be a clean process. SKF Grease Filler Pumps
are designed to help achieve this goal.
Technical data
Designation LAGF 18 LAGF 50
Maximum pressure 30 bar (430 psi) 30 bar (430 psi)
Volume/stroke approx. 45 cm3 (1.5 US fl. oz) approx. 45 cm3 (1.5 US fl. oz)
Suitable drum dimensions:
inside diameter 265285 mm (10.411.2 in.) 350385 mm (13.815.2 in.)
maximum inside height 420 mm (16.5 in.) 675 mm (26.6 in.)
Weight 5 kg (11 lb) 7 kg (15 lb)
Note: Most suitable in conjunction with SKF Grease Filler Pumps LAGF Series
Technical data
Designation VKN 550
Bearing range
inner diameter (d) 19 to 120 mm (0.7 to 4.7 in.)
outer diameter (D) max. 200 mm (7.9 in.)
176
For high volume requirements
SKF Grease Pumps LAGG series
SKF manual and air-operated grease pumps are designed to supply large
amounts of grease. This is useful when large housings have to be filled or when
numerous points have to be lubricated. They are also suitable for topping up
centralised lubrication systems reservoirs.
Full range: pumps available for 18, 50 or 180 kg (39, 110 or 400 lb)
grease drums
High pressure: maximum of 420 bar (6 090 psi) for air-driven models
Reliable: tested and approved for SKF greases
Easy and ready to install
3,5 m (11.5 ft) of tubing included
LAGG 18M LAGG 18AE LAGG 50AE LAGG 180AE LAGT 180
Technical data
Designation LAGG 18M LAGG 18AE LAGG 50AE LAGG 180AE LAGT 180
Description Grease pump for Mobile grease pump Grease pump Grease pump Trolley for drums
18 kg (39.6 lb) for 18 kg (39.6 lb) for 50 kg (110 lb) for 180 kg (396 lb) up to 200 kg
drums drums drums drums (440 lb)
Power source Manual Airpressure Airpressure Airpressure n.a.
Max. pressure 500 bar (7 250 psi) 420 bar (6 090 psi) 420 bar (6 090 psi) 420 bar (6 090 psi) n.a.
Suitable drum 265285 mm 265285 mm 350385 mm 550590 mm n.a.
(10.411.2 in.) (10.411.2 in.) (13.815.2 in.) (21.723.2 in.)
Mobility Stationary Trolley included Stationary Stationary Trolley
Maximum flow rate 1,6 cm3/stroke 200 cm3/min. 200 cm3/min. 200 cm3/min.
(0.05 US fl. oz) (6.8 US fl. oz) (6.8 US fl. oz) (6.8 US fl. oz)
Suitable grease 0002 02 02 02
NLGI class
177
Accurate grease quantity measurement
SKF Grease Meter LAGM 1000E
The amount delivered per stroke by grease guns depends on many variables.
It is generally difficult to supply an accurate quantity of grease when manually
lubricating bearings. The right amount of grease, however, is critical for the
bearings service life, as over- or under-greasing can result in machine
breakdown. Although a common practice is to weigh the grease per stroke,
this procedure does not consider the backpressure, the ongoing wear inside
the grease gun or any other variables.
The SKF Grease Meter LAGM 1000E accurately measures grease discharge in volume or weight in
metric (cm3 or g) or US units (US fl. oz or oz), making conversion calculations unnecessary.
Technical data
Designation LAGM 1000E
Housing material Aluminium, anodised
Weight 0,3 kg (0.66 lb)
IP rating IP 67
Suitable greases NLGI 0 to NLGI 3
Maximum operating pressure 700 bar (10 000 psi)
Maximum grease flow 1 000 cm3/min (34 US fl. oz/min)
Thread connections M10x1
Display Lit LCD (4 digits / 9 mm)
Accuracy 3% from 0 to 300 bar
5% from 300 to 700 bar
Selectable units cm3, g, US fl. oz or oz
Display lamp auto switch off 15 seconds after last pulse
Battery type 1 1,5 V AA Alkaline
Unit auto switch off Programmable
178
Transfer tools
A smarter way to handle your hoses
Hose reels TLRC & TLRS series
Hoses are required anywhere flexible ways of conveying fluids are required.
However, their flexible nature make them difficult to keep tidy and untangled.
Hose reels are designed to help solve that problem.
TLRS
Technical data
Designation Pressure Max. temp. Hose I.D. Hose length M (G) F (G) Hose Application
Outlet Inlet colour
bar psi C F mm in. m ft in. in.
TLRC 15AW 21 300 65 150 10 3/8 15 50 1/4 1/2 Red Low pressure air / water
TLRC 15AW/W 21 300 65 150 13 1/2 15 50 1/2 1/2 Red Low pressure air / water
TLRS 15AW 21 300 65 150 10 3/8 15 50 1/4 1/2 Red Low pressure air / water
TLRS 22AW 21 300 65 150 10 3/8 22 72 1/4 1/2 Red Low pressure air / water
TLRS 15AW/W 21 300 65 150 13 1/2 15 50 3/8 1/2 Red Low pressure air / water
TLRS 15H 138 2 000 99 210 13 1/2 15 50 1/2 1/2 Black Medium pressure oil
TLRS 8G 400 5 800 99 210 6 1/4 8 25 1/4 1/4 Black High pressure grease
179
Accessories
Renew or upgrade your equipment
SKF Grease Nozzles LAGS 8
The SKF Grease Nozzles LAGS 8 kit provides practical accessories for daily
lubrication, such as connectors, couplings and nozzles that are most widely
used in the industry.
Technical data
Designation LAGS 8
Maximum working pressure 400 bar (5 800 psi)
Minimum burst pressure 800 bar (11 600 psi)
Carrying case dimensions 530 85 180 mm (20.9 3.4 7.0 in.)
Kit contents
LAGS 8 Quantity
Straight pipe 180 mm and nozzle (DIN 71412) 1
Hose with nozzle (DIN 71412) 1
Tube with nozzle for buttom head grease fittings (DIN 3404) 1
Tube with nozzle for Flush type grease fittings and plastic transparent cover (DIN 3405) 1
Grease fitting M10x1G 1/8 1
Grease fitting M10x1 1/8 27NPS 1
Nozzle (DIN 71412) 2
Technical data
Designation LAGN 120
Maximum working pressure 400 bar (5 800 psi)
Minimum burst pressure 800 bar (11 600 psi)
Kit contents
Grease fitting type Quantity Grease fitting type Quantity Grease fitting type Quantity
M6x1 straight 30 M6x1 45 5 M6x1 90 5
M8x1 straight 20 M8x1 45 10 M8x1 90 10
M10x1 straight 10 M10x1 45 5 M10x1 90 5
G 1/8 straight 10 G 1 /8 45 5 G 1/8 90 5
180
Proper identification of your lubrication points
SKF Grease fitting caps and tags TLAC 50
In conjunction with the SKF Lubrication Planner software, grease fitting caps
and tags offer a complete solution to protect lubrication fittings from external
contamination and simultaneously allow for proper identification.
Technical data
Description Value
Label dimensions 45 21 mm (1.8 0.8 in.)
Material LLDP + 25% EVA
Temperature range from 20 to +80 C (5 to +175 F)
Suitable for grease fitting sizes G 1/4, G 1/8, M6, M8, M10 and grease fitting head
Kits contents
Kit designation Description
TLAC 50/B 50 blue caps and tags + 2 printable stickers sheets
TLAC 50/Y 50 yellow caps and tags + 2 printable stickers sheets
TLAC 50/R 50 red caps and tags + 2 printable stickers sheets
TLAC 50/G 50 green caps and tags + 2 printable stickers sheets
TLAC 50/Z 50 black caps and tags + 2 printable stickers sheets
TLAT 10 10 printable stickers sheets
Technical data
Designation TMBA G11D
Pack size 25 pairs
Size 9
Colour blue
181
Storage tools
Keep your oil clean from the beginning
Oil storage station
Granting a clean oil is a key step towards machinery reliability. These stations help to ensure each oil
has the right cleanliness code (ISO 4406) when it reaches the machine. It can clean the oil while its
being loaded, when it is dispensed, and maybe most important, while it stays idle in the tank. It is
equipped with independent filters, valves and pumps and uses a tailor-made set of colours to avoid
cross contamination
Features
Choice of four aluminized steel tank sizes: 113, 246, 454 and 908 litre Filtration all systems come with fluid filtration capability with a
(30, 65, 120 and 240 US gal) choice of micron ratings and also desiccant air breathers
Scalable and configurable scale system to accommodate the number of Accommodates lubricants up to ISO VG 680
lubricants required for storage and dispensing All systems ship in fully assembled pods for efficient freight and
Choice of 10 tank colours rapid on-site installation
Spill control all systems come standard with integrated spill pans Transport all systems have integrated spill transport pallets for easy
for SPCC compliance and overall environmental protection forklift and hand truck access for freight and workplace mobility
Fire suppression includes MSHA-CFR30 rated flame resistant fire Power all systems come standard with 110 V single phase TEFC motors
suppression hoses as standard with optional fusible link tank isolation and can be configured for other power supplies as required
valves and auto-shut off taps
182
Oil inspection and dispensing
Automatic adjustment for optimal lubricating oil level
SKF Oil Levellers LAHD series
SKF LAHD 500 and LAHD 1000 oil levellers are designed to automatically
compensate oil evaporation and leakages under running conditions. This
helps in maintaining the correct oil level within a bearing housing, gear box,
crankcase, or similar oil bath application. The SKF LAHD series optimises
machine performance and increases their service life. Furthermore, they
enhance the possibility of an accurate visual inspection of the oil level.
Technical data
Designation LAHD 500 / LAHD 1000
Reservoir volume
LAHD 500 500 ml (17 US fl. oz)
LAHD 1000 1 000 ml (34 US fl. oz)
Boundary dimensions
LAHD 500 91 mm 290 mm high (3.6 11.4 in.)
LAHD 1000 122 mm 290 mm high (4.8 11.4 in.)
Allowed temperature range 20 to +70 C (5 to +158 F)
Length of connecting tube 600 mm (23.5 in.)
Connection thread G 1/2
Suitable oil types Mineral and synthetic oils
183
A proper solution for oil handling
Oil handling containers LAOS series
LAOS series is comprised of an extensive assortment of drums and dispensing
lids ideal for the storage and administration of fluids and oil lubricants. The lids
are available in ten different colours to fit colour coded identification systems.
184
Drums Pumps Hose extensions
Designed with wide necks and a standard thread Standard pump suitable for viscosities up to ISO Designed to extend the reach of the lids.
size. Fits any LAOS lid. Available in 5 different VG 460. High flow (approx. 14 strokes per litre/US Two different versions available for stumpy and
sizes. quart). High viscosity pump for viscosities up to stretch lids. The stretch versions length can be
ISO VG 680. High efficiency with approx. 12 adjusted by removing the fitting and cutting it
strokes per litre/US quart. As a protection against down to the desired size.
airborne contaminants during the pumping
process, a 10 micron breather is available. For
both pumps an anti-drip long discharge hose of
1,5 m (4.9 ft) and reducer nozzles are available.
LAOS 63595 3 litre drum (0.8 US gal) LAOS 62567 Standard Pump
(to fit LAOS utility lids)
LAOS 63618 5 litre drum (1.3 US gal) LAOS 09422 Pump reducer nozzle
185
Lubrication analysis tools
Portable grease analysis kit for field use
SKF Grease Test Kit TKGT 1
Lubricant analysis is a vital part of a predictive maintenance strategy. Until recently,
however, oils were almost always analysed despite the fact that around 80% of bearings
are lubricated with grease. Tribology expertise and years of research have allowed SKF to
develop a complete methodology to assess grease condition.
Extremely useful in field decision-making processes Provides more information on root cause analysis
Allows adjustment of grease relubrication intervals Requires no special training to perform the tests
according to real conditions Requires no harmful chemicals
Grease can be evaluated to detect possible Small sample sizes required. Only 0,5 g of grease
unacceptable deviations from batch to batch is needed to perform all the tests
Allows verification of the suitability of certain
greases in specific applications
Helps in the prevention of damage due to
underperforming lubricant greases
Consistency test
(Patent applied for)
Contamination evaluation
186
Technical data
Designation TKGT 1
Parts Components Quantity Specifications
Sampling tools Sampling syringe 1 Polypropylene
Sampling tube 1 PTFE, length approx. 1 m
Permanent marker 1 Black
Sampling containers 10 35 ml polyethylene
Gloves 10 pairs Grease resistant nitrile (synthetic rubber), powder free, size XL, colour blue
Disposable spatulas 1 Set of 25
250 mm stainless steel spatula 1 Stainless steel
150 mm stainless steel spatula 1 Stainless steel
Scissors 1 Stainless steel
Consistency test Housing 1 Aluminium
Weight 1 Stainless steel
Mask 1 Plexiglas
Glass plates 4
Oil bleeding test USB heater 1 2,5 W5 V
USB/220/110 V adaptor 1 Universal (EU, US, UK, Australia) to USB
Paper pack 1 Contains 50 sheets
Ruler 1 Aluminium graduated 0,5 mm
Contamination Pocket microscope 1 60100x with light
test Batteries 2 AAA
Carrying case CD 1 Contains instructions for use, report template, and consistency test scale
Carrying case 1 Dimensions: 530 110 360 mm (20.9 4.3 14.2 in.)
187
Lubrication software
For access or download: skf.com/lubrication or skf.com/kc
LubeSelect for SKF greases provides you a user friendly tool to select the
LubeSelect for SKF greases right grease and suggest frequency and quantity, while taking into
account the particular conditions of your application. General guidelines
for typical greases for different applications are also available.
188
Quick tool for relubrication calculation
SKF DialSet
SKF DialSet has been designed to help you to set up your SKF automatic
lubricators. After selecting the criteria and grease appropriate for your
application, the program provides you with the correct settings for your
SKF automatic lubricators. It also provides a quick and simple tool for
relubrication intervals and quantity calculations.
Stand-alone program Allows quick calculation of the relubrication intervals based on the
operating conditions of your application
Calculations are based on SKF lubrication theories
Calculated lubrication intervals depend on the properties of the
selected grease, thereby minimising the risk of under- or
overlubrication and optimising grease consumption
Calculations take into account SKF automatic lubrication systems,
grease dispense rates, thus facilitating the selection of the correct
lubricator setting
Recommended grease quantity depends on the grease replenishment
position; side or W33 for optimum grease consumption
Includes a complete list of the SKF SYSTEM 24 accessories
DialSet stand-alone
The stand-alone version of DialSet is available in multiple languages and
Online program is suitable for PCs working with Microsoft Windows.
Download it from skf.com/lubrication
DialSet online
DialSet for smartphones DialSet is also available online in English language. The program is
accessible free-of-charge from mapro.skf.com/dialset
189
Designation index
Designation Description Page Designation Description Page
1008593 E Nipple with pipe thread (G) 71 729865 B Feeler gauge 69
1009030 B Nipple with pipe thread (G) 71 729944 E Plug for oil ducts and vent holes 70
1009030 E Nipple with pipe thread (G) 71 CMAS 100-SL Machine condition advisor 121
1012783 E Nipple with pipe thread (G) 71 CMSS 200 Machine condition indicator 120
1014357 A Nipple with pipe thread (G) 71 Custom shims Machinery shims 92
1016402 E Nipple with pipe thread (G) 71 EAZ series Fixed induction heaters 49
1018219 E Nipple with pipe thread (G) 71 EAZ 80/130 series Adjustable induction heaters 50
1018220 E Nipple with pipe thread (G) 71 EAZ 130/170 series Adjustable induction heaters 50
1019950 Nipple with pipe thread (G) 71 HMVA 42/200 Hydraulic nut drive-up adapter 55
1020612 A High pressure pipe 68 HMV ..E series Hydraulic nuts 56
1030816 E Plug for oil ducts and vent holes 70 HMV ..E/A101 Hydraulic nuts without threads 60
1077453/100MPA Extension pipe 72 HMVC ..E series Hydraulic nuts, inch thread series 59
1077454/100MPA Connection nipple 72 HN 4-16/SET Hook spanner set 12
1077455/100MPA Nipple with pipe thread (G) 71 HN ../SNL series Hook spanners for SNL housings 14
1077456/100MPA Nipple with pipe thread (G) 71 HN series Hook spanners 12
1077587 Pressure gauge 67 HNA series Adjustable hook spanners 13
1077587/2 Pressure gauge 67 LAGD 125 SKF SYSTEM 24 automatic lubricator 162
1077589 Pressure gauge 67 LAGD 60 SKF SYSTEM 24 automatic lubricator 162
1077589/3 Pressure gauge 67 LAGF 18 Grease filler pump 176
1077600 Grease gun 172 LAGF 50 Grease filler pump 176
1077600H Grease gun with hose 173 LAGG 180AE Grease pump 177
1077600/SET Grease gun set 173 LAGG 18AE Mobile grease pump 177
1077601 Flexible hose 173 LAGG 18M Grease pump 177
226400 E Oil injector 64 LAGG 50AE Grease pump 177
226400 E/400 Oil injector 64 LAGH 400 Grease gun 173
226402 Adapter block 73 LAGM 1000E Grease meter 178
227957 A High pressure pipe 68 LAGN 120 Grease nipples 180
227958 A High pressure pipe 68 LAGP 400 Grease packer 172
227965/100MPA Extension pipe 72 LAGS 8 Grease nozzles 180
227966/100MPA Extension pipe 72 LAGT 180 Trolley for drums 177
228027 E Nipple with pipe thread (G) 71 LAHD 500 Oil leveller 183
233950 E Plug for oil ducts and vent holes 70 LAHD 1000 Oil leveller 183
234063 Connection nipple 72 LAOS series Oil handling containers 184
234064 Extension pipe 72 LAP.. series Accessories for SKF automatic lubricators 170
721740 A High pressure pipe 68 LABP 5-16/2K Elevator kit 171
728017 A High pressure pipe 68 LDTS 1 Dry film lubricant 152
728619 E Hydraulic pump 63 LFFG 220 Food grade gear oil 150
729100 Quick connection nipple 70 LFFG 320 Food grade gear oil 150
729101/300MPA Oil injection kit 65
LFFH 46 Food grade hydraulic oil 149
729101/400MPA Oil injection kit 65
LFFH 68 Food grade hydraulic oil 149
729106/100MPA Connection nipple (NPT and G) 71
LFFM 80 Food grade chain oil 151
729124 Hydraulic pump 62
LFFT 220 Food grade chain oil 151
729124DU Hydraulic pump with digital gauge 54
LGAF 3E Anti-fretting agent 38
729126 High pressure hose 69
LGBB 2 Wind turbine blade and yaw grease 137
729146 Nipple with pipe thread (G) 71
LGED 2 High temperature and harsh environment grease 145
729654/150MPA Connection nipple (NPT and G) 71
LGEM 2 High viscosity grease 141
729655/150MPA Connection nipple (NPT and G) 71
LGEP 2 Extreme pressure grease 134
729656/150MPA Connection nipple (NPT and G) 71
LGET 2 Extreme high temperature grease 146
729659 C Electric hot plate 47
LGEV 2 Extremely high viscosity grease 142
729831 A Quick connection coupling 70
LGFP 2 Food compatible grease 147
729832 A Quick connection nipple 70
LGFQ 2 High load food grade grease 148
729834 High pressure hose 69
LGGB 2 Biodegradable grease 136
729865 A Feeler gauge 69
190
Designation Description Page Designation Description Page
LGHB 2 High viscosity, high temperature grease 143 TKSA 31 Shaft alignment tool 81
LGHP 2 High performance grease 144 TKSA 41 Shaft alignment tool 82
LGLS 0 Low temperature chassis grease 153 TKSA 51 Shaft alignment tool 83
LGLT 2 Low temperature, high speed grease 138 TKSA 71 Shaft alignment tool 84
LGMT 2 General purpose grease 132 TKSA 71/PRO Shaft alignment tool 84
LGMT 3 General purpose grease 133 TKSA 71D Shaft alignment tool 84
LGWA 2 High load, extreme pressure grease 135 TKSA 71D/PRO Shaft alignment tool 84
LGWM 1 Extreme pressure, low temperature grease 139 TKSA accessories Accessories for TKSA series 87
LGWM 2 High load, wide temperature grease 140 TKSA DISPLAY Android tablet 85
LHDF 900 Dismounting fluid 73 TKTI 21 Thermal camera 106
LHFP 150 Food compatible chain oil 151 TKTI 31 Thermal camera 106
LHHT 265 High temperature chain oil 154 TKTL 10 Infrared thermometer 102
LHMF 300 Mounting fluid 73 TKTL 20 Infrared and contact thermometer 102
LHMT 68 Medium temperature chain oil 154 TKTL 30 Infrared and contact thermometer 102
LHRP 2 Anti-corrosive agent 39 TKTL 40 Infrared and contact thermometer 103
LMCG 1 Grid and gear coupling grease 153 TLAC 50 Grease fitting caps and tags 181
Oil storage station Oil storage station 182 TLGB 20 Battery driven grease gun 174
SKF DialSet Relubrication calculation program 189 TLGB 20/110V Battery driven grease gun 175
SKF LubeSelect Grease selection and relubrication calculation 188 TLGH 1 Grease gun 172
SKF Lubrication Lubrication planning program 188 TLMP series Multi point automatic lubricator 168
Planner
TLRC Hose reel 179
SKF Vibracon Universal adjustable chock 93
TLRS Hose reel 179
SM SPS series Spherical shims 92
TLSD 125 Electro-mechanical single point automatic 164
SMSW series Spherical washers 94 lubricators
THAP 030E Air-driven pump 66 TLSD 250 Electro-mechanical single point automatic 164
lubricators
THAP 030E/SK1 Air-driven pump set 66
TLMR 101 Electro-mechanical single point automatic 166
THAP 150E Air-driven pump 66
lubricators
THAP 150E/SK1 Air-driven pump set 66
TLMR 201 Electro-mechanical single point automatic 166
THAP 300E Air-driven injector 66 lubricators
THAP 300E/SK1 Air-driven injector set 66 TMAS series (inches) Machinery shims 90
THAP 400E Air-driven injector 66 TMAS series (metric) Machinery shims 91
THAP 400E/SK1 Air-driven injector set 66 TMBA G11 Heat resistant gloves 51
THGD 100 Digital oil pressure gauge 67 TMBA G11D Disposable grease resistant gloves 181
THKI 300 Oil injector set 65 TMBA G11ET Extreme heat resistant gloves 51
THKI 400 Oil injector set 65 TMBA G11H Heat and oil resistant gloves 51
TIH 030m Induction heater 42 TMBH 1 Portable induction heater 42
TIH 100m Induction heater 42 TMBP 20E Blind housing puller kit 30
TIH 220m Induction heater 43 TMBR series Aluminium heating ring series 48
TIH L series Induction heater 43 TMBS 50E Strong back puller 28
TIL L MB series Solid workpiece heaters 45 TMBS 100E Strong back puller 28
TIH MC series Multi-core induction heaters 47 TMBS 150E Strong back puller 28
TKBA 10 Belt alignment tool 96 TMCD 10R Horizontal dial indicator, mm 54
TKBA 20 Belt alignment tool 96 TMCD 5P Vertical dial indicator 54
TKBA 40 Belt alignment tool 96 TMDC 1/2R Horizontal dial indicator, in 54
TKDT 10 Contact thermometer 101 TMDT 2-30 Standard surface probe 105
TKED 1 Electrical discharge detector pen 119 TMDT 2-31 Magnetic surface probe 105
TKES 10 series Video endoscope 114 TMDT 2-32 Insulated surface probe 105
TKGT 1 Grease test kit 186 TMDT 2-33 Right angle surface probe 105
TKRS 10 Stroboscope 112 TMDT 2-34 Gas and liquid probe 105
TKRS 20 Stroboscope 112 TMDT 2-34/1.5 Gas and liquid probe 105
TKRT 10 Tachometer 110 TMDT 2-35 Probe with sharp tip 105
TKRT 20 Tachometer 110 TMDT 2-36 Pipe clamp probe 105
TKSA 11 Shaft alignment tool 80 TMDT 2-37 Extension cable 105
191
Designation index
Designation Description Page Designation Description Page
TMDT 2-38 Wire probe 105 TMMA 100H/SET SKF EasyPull - Hydraulic jaw puller set 23
TMDT 2-39 High temperature wire probe 105 TMMD 100 Deep groove ball bearing puller kit 31
TMDT 2-40 Rotating probe 105 TMMK 10-35 Combi kit 18
TMDT 2-41 Non-ferrous foundry probe 105 TMMK 20-50 Combi kit 18
TMDT 2-42 Ambient temperature probe 105 TMMP 6 Heavy duty jaw puller 24
TMDT 2-43 Heavy duty surface probe 105 TMMP 10 Heavy duty jaw puller 24
TMEH 1 Oil check monitor 187 TMMP 15 Heavy duty jaw puller 24
TMEM 1500 SensorMount indicator 74 TMMP 2x65 Standard jaw puller 24
TMFN series Impact spanners 16 TMMP 2x170 Standard jaw puller 24
TMFS series Axial lock nut sockets 15 TMMP 3x185 Standard jaw puller 24
TMFT 24 Bearing fitting tool kit 10 TMMP 3x230 Standard jaw puller 24
TMFT 36 Bearing fitting tool kit 10 TMMP 3x300 Standard jaw puller 24
TMHC 110E Hydraulic puller kit 28 TMMR 4F/SET Reversible jaw puller set 27
TMHK 35 Mounting & dismounting kit for OK Couplings 75 TMMR 8F/SET Reversible jaw puller set 27
TMHK 36 Mounting & dismounting kit for OK Couplings 75 TMMR 8XL/SET Reversible jaw puller set 27
TMHK 37 Mounting & dismounting kit for OK Couplings 75 TMMR 40F Reversible jaw puller 26
TMHK 38 Mounting & dismounting kit for OK Couplings 75 TMMR 60F Reversible jaw puller 26
TMHK 38S Mounting & dismounting kit for OK Couplings 75 TMMR 80F Reversible jaw puller 26
TMHK 39 Mounting & dismounting kit for OK Couplings 75 TMMR 120F Reversible jaw puller 26
TMHK 40 Mounting & dismounting kit for OK Couplings 75 TMMR 160F Reversible jaw puller 26
TMHK 41 Mounting & dismounting kit for OK Couplings 75 TMMR 200F Reversible jaw puller 26
TMHN 7 Lock nut spanner kit 17 TMMR 250F Reversible jaw puller 26
TMHP 10E Hydraulic jaw puller kit 27 TMMR 350F Reversible jaw puller 26
TMHP 15 series Hydraulically assisted heavy duty jaw puller 25 TMMR 160XL Reversible jaw puller 26
TMHP 30 series Hydraulically assisted heavy duty jaw puller 25 TMMR 200XL Reversible jaw puller 26
TMHP 50 series Hydraulically assisted heavy duty jaw puller 25 TMMR 250XL Reversible jaw puller 26
TMHS 75 Advanced hydraulic spindle 36 TMMR 350XL Reversible jaw puller 26
TMHS 100 Advanced hydraulic spindle 36 TMMS 50 Tri-section pulling plate 37
TMIC 7-28 Internal bearing puller kit 33 TMMS 100 Tri-section pulling plate 37
TMIP 7-28 Internal bearing puller kit 33 TMMS 160 Tri-section pulling plate 37
TMIP 30-60 Internal bearing puller kit 33 TMMS 260 Tri-section pulling plate 37
TMJL 100 Hydraulic pump 63 TMMS 380 Tri-section pulling plate 37
TMJL 100DU Hydraulic pump with digital gauge 54 TMMX 210 Puller protection blanket 38
TMJL 50 Hydraulic pump 62 TMMX 280 Puller protection blanket 38
TMJL 50DU Hydraulic pump with digital gauge 54 TMMX 350 Puller protection blanket 38
TMMA 60 SKF EasyPull - Mechanical jaw puller 22 TMSP 1 Sound pressure meter 117
TMMA 80 SKF EasyPull - Mechanical jaw puller 22 TMST 3 Electronic stethoscope 116
TMMA 120 SKF EasyPull - Mechanical jaw puller 22 TMSU 1 Ultrasonic leak detector 118
TMMA 75H SKF EasyPull - Hydraulic jaw puller 22 TMTP 200 General purpose thermometer pen 101
TMMA 75H/SET SKF EasyPull - Hydraulic jaw puller set 23 VKN 550 Bearing packer 176
TMMA 100H SKF EasyPull - Hydraulic jaw puller 22
192
skf.com | mapro.skf.com | skf.com/lubrication
SKF, CARB, DUOFLEX, LUBRILEAN, MONOFLEX, MULTIFLEX, SENSORMOUNT, SYSTEM 24 and
VIBRACON are registered trademarks of the SKF Group.
KEVLAR is a registered trademark of DuPont.
Microsoft and Windows are either registered trademarks or trademarks of
Microsoft Corporation in the United States and/or other countries.
App Store is a service mark of Apple Inc. registered in the US and other countries.
Android and Google Play are trademarks of Google Inc.