Professional Documents
Culture Documents
Ion Exchange Chromatography - Amersham
Ion Exchange Chromatography - Amersham
ion
exchange media
Sephadex ion exchange media are widely used for process scale
applications. Their separation power, ease of use and overall
economy make them suitable for both column and batch
techniques.
Table 1 shows the full range of eight Sephadex ion
exchangers. Anion and cation exchangers are
designated A-25 or A-50 and C-25 or C-50
respectively.
18-1117-58
Edition AA
2
The terms strong and weak refer to the extent of
variation of ionization with pH and not to the
strength of binding. Strong exchangers (QAE and
SP Sephadex) are completely ionized over a wide
pH range whereas the charge of weak exchangers is
pH dependent. Weak anion exchangers loose
charge when pH increases whereas weak cation
exchangers gain charge.
Table 2 summarizes the main characteristics of
Sephadex ion exchangers.
Bead form
Sephadex is a dry, bead-formed gel prepared by
cross-linking dextran with epichlorohydrin. The gel
swells in aqueous solutions. Different types of
Sephadex belonging to the G-series differ in their
degree of cross-linking and hence in their degree of
swelling.
Sephadex ion exchangers are derived from either
Sephadex G-25 or Sephadex G-50. The G-25
matrix is more highly cross-linked than the G-50.
Ion exchangers based on Sephadex G-25 have
greater rigidity and thus swell less than those based
on G-50, which are less rigid (see Table 6).
These properties mean that A-25 and C-25 type ion
exchangers are a good choice for small molecules
up to about 30 000 MW (e.g. peptides,
oligosaccharides and oligonucleotides) whereas
A-50 and C-50 types are better suited to larger
biomolecules, such as proteins in the molecular
weight range 30 000 to 100 000. High molecular
weight molecules, which are excluded from the
bead, may be adsorbed to some extent on the outer
surface.
As described later, Sephadex A-50 and C-50 ion
exchangers are ideal for batch separations.
DEAE Sephadex QAE Sephadex CM Sephadex SP Sephadex
Type of exchanger Mixed weak and Strong anion Weak cation Strong cation
strong* anion exchanger exchanger exchanger exchanger
Main functional group Diethylaminoethyl Diethyl-(2-hydroxy- Carboxymethyl Sulphopropyl
propyl)aminoethyl
Counter ion Chloride Chloride Sodium Sodium
Rec. pH working range 29 210 610 210
Dynamic capacity See Tables 3 and 4.
Mol wt range A-25 and C-25 types: up to 30 000.
A-50 and C-50 types: 30 000100 000.
Bead form Spherical, 40-125 m in dry form
Bead structure Cross-linked dextran
Chemical stability Stable in water, salt solutions, organic solvents, alkaline and
weakly acidic solutions and denaturing solvents
Physical stability A-25 and C-25 types: robust have good ow properties and
negligible volume changes due to changes in pH and ionic strength.
A-50 and C-50 types: volume may vary due to changes in pH and ionic strength.
Autoclavable Swollen, in salt form for 30 min at 120 C.
Availability Supplied dry in a range of laboratory and process scale pack sizes.
See ordering information
Table 2. General characteristics of Sephadex ion exchange media.
* See Table 1.
Type Description
DEAE Sephadex A-25 Mixed weak and strong
A-50 anion exchanger*
QAE Sephadex A-25 Strong anion exchanger
A-50
CM Sephadex C-25 Weak cation exchanger
C-50
SP Sephadex C-25 Strong cation exchanger
C-50
Table 1. The range of Sephadex ion exchangers. See Table 2
for more detailed information.
* DEAE Sephadex contains functional groups that display both
strong and weak ion exchange groups (1/3 strong, 2/3 weak).
3
Capacity
Due to the differences in swelling, ion exchangers
based on Sephadex G-25 have a higher ionic
capacity per ml swollen gel than those based on
G-50. Dynamic capacity also depends on the pH,
ionic strength and the nature of the sample (see
Tables 3 and 4).
Stability
Sephadex ion exchangers are insoluble in all
solvents commonly used in liquid chromatography.
They are stable in water, salt solutions, organic
solvents, and alkaline and weakly acidic solutions
in the pH range of 210. The media can be
autoclaved as a slurry in the salt form for 30
minutes at 120 C and pH 7. Exposure to strong
oxidising agents or dextranases should be avoided.
When media are stored in the swollen state, a non-
ionic antimicrobial agent should be included in the
buffer.
The high mechanical stability of Sephadex A-25
and C-25 media gives outstanding ow properties,
which makes them ideal for packing and operating
in large scale chromatography columns.
The pressure/ow rate curve shown in Figure 1
illustrates the relationship between the pressure
drop over a packed bed of DEAE Sephadex A-25
and the linear ow rate in a 5 cm i.d. column with
a bed height of approximately 10 cm. The curve is
essentially linear in the typical operating range up
to 0.15 bar where the uid velocity is about
380 cm/h for this batch. The maximum pressure
drop i.e. that pressure drop where the ow rate
levels off was not determined in this case.
Thyroglobulin HSA -lactalbumin
Protein (MW) (669 000) (68 000) (14 300)
DEAE Sephadex A-25 1.0 30.0 140.0
A-50 2.0 110.0 50.0
QAE Sephadex A-25 1.5 10.0 110.0
A-50 1.2 80.0 30.0
Table 3. Dynamic capacity (mg/ml swollen gel) data for DEAE and QAE Sephadex
ion exchangers.
Capacities were determined at a ow rate of 75 cm/h. The buffer was 0.05 M Tris, pH 8.3.
IgG Bovine COHb
Protein (MW) (160 000) (69 000)
CM Sephadex C-25 1.6 70.0
C-50 7.0 140.0
SP Sephadex C-25 1.1 70.0
C-50 8.0 110.0
Table 4. Dynamic capacity (mg/ml swollen gel) data for CM and SP Sephadex ion
exchangers.
Capacities were determined at a ow rate of 75 cm/h. The buffer was 0.1 M acetate buffer,
pH 5.0.
Flow rate
(cm/h)
450
400
350
300
250
200
150
100
50
0
0 0.05 0.1 0.15 0.2
bar
Fig. 1. The pressure/ow rate curve for a 10 cm bed of DEAE
Sephadex A-25 in a 5 cm i.d. column is essentially linear,
which demonstrates the suitability of Sephadex A-25 and C-25
ion exchangers for column use.
4
Sephadex A-50 and C-50 media, which are less
rigid and therefore more prone to volume changes,
are better suited to the batch technique. Batch
separation is simple to perform and no technical
difficulties are caused by the swelling or shrinkage
of the ion exchanger.
Batch to batch reproducibility
Consistent quality and performance from batch-to-
batch is important for all separation media, but it
assumes extra signicance when the media are
routinely used in industrial processes, as is the case
with Sephadex ion exchangers. Some randomly
selected quality control data gathered from over
30 years prove beyond doubt that these media have
been produced with outstanding batch-to-batch
consistency (see Table 5).
Swelling varies with ionic strength
and pH
Ion exchangers based on Sephadex swell in
aqueous solutions. As an example, Table 6 shows
dry and hydrated bead sizes of Sephadex cation
and anion exchangers.
As dry media are swollen before use, it is the wet
bead diameter that is of practical importance when
choosing the correct type of equipment to use, e.g.
mesh size of the column nets.
Initial swelling of dry Sephadex ion exchangers
should be performed in 0.2 M salt. In distilled
water the beads will swell too much, too quickly,
which may cause breakage.
Swelling varies with ionic strength and pH. A-25
and C-25 exchangers have a fairly rigid bead
structure and size variations due to changes in pH
or ionic strength are therefore small. A-50 and
C-50 exchangers, on the other hand, swell more
than their A-25 and C-25 equivalents due to their
less rigid structure. In addition, swelling at a given
pH is highest at low ionic strengths as repulsion
between similarly charged groups on the matrix is
then maximal (see Fig 2). Fluctuations in swelling
will be minimized in buffers with ionic strengths
above 0.1.
A similar pattern can be seen in Figure 3, which
shows how pH affects the degree of swelling. Note,
however, that the swelling of the strong ion
exchangers QAE and SP Sephadex is virtually
independent of pH since, as strong exchangers,
they remain charged over a wide pH range.
Separation principle
The separation effect of ion exchange chromato-
graphy depends on the reversible adsorption of
charged solute molecules to immobilized groups of
opposite charge. Most separations can be described
in ve stages.
Flow rate at Function; salt conc. in elution peak; M NaCl Total capacity
Lot. No. p/L=10 [cm/h] CO Hb1 CO Hb2 HSA mmolCl
/g
(Limits) (min. 60) (0.040.07) (0.060.10) (0.160.22) (3.04.0)
5042 1972 0.06 0.09 0.20 3.40
18896 1981 97 0.06 0.09 0.19 3.30
2783 1986 83 0.05 0.07 0.16 3.40
13799 1991 103 0.05 0.07 0.17 3.42
226550 1994 90 0.05 0.07 0.17 3.29
Table 5. Batch to batch reproducibility is demonstrated by some typical data from the quality control of DEAE Sephadex A-50.
Hydrated median Diameter ratio
Product Medium diameter m* hydrated/dry*
DEAE Sephadex A-25 0.15 M NaCl 127 1.83
DEAE Sephadex A-25 0.50 M NaCl 121 1.75
DEAE Sephadex A-50 0.15 M NaCl 214 3.17
DEAE Sephadex A-50 0.50 M NaCl 182 2.69
CM Sephadex C-25 0.15 M NaCl 131 1.94
CM Sephadex C-25 0.50 M NaCl 125 1.86
CM Sephadex C-50 0.15 M NaCl 250 3.41
CM Sephadex C-50 0.50 M NaCl 221 3.02
Table 6. Hydrated bead sizes of Sephadex ion exchangers. Note that lower ionic strengths will give higher hydrated/dry
diameter ratios.
* Average values from three product batches of each ion exchanger.
5
Stage one is equilibration. The pH and ionic
strength of the equilibration buffer are adjusted to
favour binding of the molecules of interest in the
solute. Weak ion exchangers have their own
buffering capacities and need longer equilibration
times. At this stage the immobilized groups are
associated with exchangeable counter ions.
Stage two is sample application and adsorption.
Solute molecules of interest displace the counter
ions and bind reversibly to the gel. Unbound
substances can be washed out using starting buffer.
(An alternative strategy sometimes used is to bind
the contaminants at this stage, in which case, it is
the the substance of interest that is washed out of
the gel.)
Note that contaminants may compete with the
substance of interest and also bind at stage two,
thus reducing the capacity for binding the intended
60
50
40
30
20
10
B
e
d
v
o
l
u
m
e
m
l
/
g
d
r
y
g
e
l
SP Sephadex
C-50
C-25
0.1 0.2 0.3 0.4 0.5
Ionic strength
60
50
40
30
20
10
B
e
d
v
o
l
u
m
e
m
l
/
g
d
r
y
g
e
l
CM Sephadex
C-50
C-25
0.1 0.2 0.3 0.4 0.5
Ionic strength
60
50
40
30
20
10
B
e
d
v
o
l
u
m
e
m
l
/
g
d
r
y
g
e
l
QAE Sephadex
A-50
A-25
0.1 0.2 0.3 0.4 0.5
Ionic strength
60
50
40
30
20
10
B
e
d
v
o
l
u
m
e
m
l
/
g
d
r
y
g
e
l
DEAE Sephadex
A-50
A-25
0.1 0.2 0.3 0.4 0.5
Ionic strength
Effect of ionic strength on swelling
Fig. 2. Bed volumes obtained from 1 gram dry gel as a function of ionic strength. DEAE and QAE Sephadex were measured in
Tris HCl buffer pH 7.6 with varying NaCl concentration. CM and SP Sephadex were measured in acetate buffer pH 4.3 with
varying NaCl concentration.
product. If this occurs, the experimental conditions
and/or the chosen ion exchanger should be changed
to favour binding the substance of interest.
Stage three involves increasing the ionic strength of
the eluting buffer or changing its pH to conditions
that favour the elution of the bound substance of
interest.
The fourth and fth stages are the removal from
the column of substances not eluted under the
previous experimental conditions followed by re-
equilibration to the starting conditions for the next
separation cycle.
Ion exchange separations can be carried out in a
column or by a batch procedure. The basic
principle outlined in the ve stages described above
applies to both methods.
6
Working with Sephadex ion exchangers
Sephadex A-25 and C-25 ion exchangers are
highly suitable for column chromatography and
Sephadex A-50 and C-50 for batch techniques.
This versatility combined with low non-specic
interaction, consistent quality, batch to batch
reliability and excellent price performance, makes
Sephadex ion exchangers an obvious choice for
large scale applications.
Column chromatography
Good column design and good packing techniques
are important in realising the full separation
potential of ion exchange chromatography.
Amersham Biosciences has columns available for ion
exchange chromatography at laboratory, pilot and
full production scales.
Our range of process columns covers all stages
from process development to full scale production
and includes INdEX
columns, BPG
columns,
Process Stack columns (PS370), BioProcess
m
s
,
U
p
p
s
a
la
9
7
.
0
4
9
6
2
2
0
2
Fig. 5. A stainless steel batch tank equipped with a stirring
system.
The gel can also be packed in a column after the
washing step and be eluted stepwise in the same
way as during normal column chromatography.
Resolution will however be lower for such a
combined batch and column procedure compared
with a normal column procedure, since the sample
is bound uniformly throughout the gel slurry and
the subsequent chromatographic bed.
Under these conditions stepwise elution is
recommended since gradient elution will give
broader bands and often poorer resolution. Also
the amount of eluent will be lower in stepwise
elution.
Batch chromatography is useful for concentrating
dilute solutions and separating the substances of
interest from gross contaminants during the initial
capture stage of a purication scheme.
Ion exchangers used in batch processes are
discarded after use, so the operator does not have
to be concerned with regeneration or cleaning-in-
place procedures. The overall economy of
Sephadex ion exchangers also favours their one
time use.
Applications of the batch technique
Batch ion exchange with Sephadex A-50 and C-50
is ideal for the simple and economical Capture of
proteins and complexes from large volumes of
feedstocks. They are particularly useful for
processing crude feedstocks that are not suitable
for loading onto a column.
IgG and prothrombin complex are representative
of a number of plasma components puried on
DEAE Sephadex A-50. Removal of detergents and
the purication of whey proteins are common
applications of CM Sephadex C-50.
Further information is available in the Amersham
Biosciences handbook Ion Exchange Chromato-
graphy Principles and Methods (article no.
18-1114-21), which is a practical guide to the
technique, its applications and experimental
procedures. Ask your local representative of
Amersham Biosciences for details.
Columns
For more information about the range of process
scale columns, please contact you local sales office
of Amersham Biosciences.